commit 50f3beb50a fixed em28xx-alsa
locking schema. However, a backport macro was kept.
This patch removes the macro, since it is not needed for the module
compilation against upstream.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replaced usb_kill_usb for usb_unlink_usb
(wait until urb to fully stop require USB core to put the calling process to sleep).
Oops:
http://www.kerneloops.org/raw.php?rawid=71799&msgid=
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video device was part of the gspca device. On device disconnection
while streaming, the device structure is freed at close time.
In this case, the remaining close job on the video device run out of
allocated memory.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The previous subdriver protection against rmmod was done via the
file operations table in the device descriptor. On device disconnection
while streaming, the device structure was freed at close time, and the
module_put still used the module name in the freed area.
Now, explicit module get/put are done on open and close.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a side effect, the sd routine stop0 is called on disconnect.
This permits the subdriver to free its resources.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Newer versions of hald tries to open it to call QUERYCAP.
Due to the lack of a proper locking, it is possible to open the device
before it finishes initialization.
This patch adds a lock to avoid this risk, and to protect the list of
em28xx devices.
While here, remove the uneeded BKL lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that we have a polling task for IR, there's a race condition, since
IR can be polling while other operations are being doing. Also, we are
now sharing the same urb_buf for both read and write control urb
operations. So, we need a mutex.
Thanks to Davin Heitmueller <devin.heitmueller@gmail.com> for warning me.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before this patch, every register setup on em28xx were dynamically
allocating a temporary buffer for control URB's to be handled.
To avoid this ping-pong, use, instead a pre-allocated buffer.
Also, be sure that read control URB's also use the buffer, instead of
relying on a stack buffer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx_init_dev() has some error conditions that are not properly
de-allocating dev var, nor freeing the device number for a future usage.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Noticed by sparse:
drivers/media/video/s2255drv.c:2531:6: warning: restricted __le32 degrades to integer
Cc: Dean Anderson <dean@sensoray.com>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The attached patch makes the em28xx auxillary audio input work.
Tested with the HVR-950.
em28xx: make auxillary audio input work
The tuner audio input was working but the aux input wasn't. Tested with
the HVR-950.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before the patch, the used ioctl were printed as an hexadecimal code,
hard to be understand without consulting the way _IO macros work.
Instead, use the V4L default handler for printing such errors into a way
that would be easier to understand.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some comments are not clear enough. Improve it to allow a better
understanding of the driver behavior.
While there, remove an unneeded struct prototype.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There were no check about the limits of shadow.bytes array. This offers
a risk of writing values outside the limits, overriding other data
areas.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of storing the pointer for the proper entry at chip description
table, the driver were storing an indirect reference, by using an index.
Better to reference directly the data.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A driver used on several bttv boards since 2000 is not experimental
anymore ;) Remove it from the comments.
While there, update copyrights addind a quick note about the "recent"
updates since 2005.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch checks for volume, bass, treble, set mode and get mode
callbacks before actually enabling the code that would use them.
Instead of aborting the driver for load, this patch will allow it to
load with a reduced number of functionatities.
This prevents OOPS if some board entry is missing a needed callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
generic_checkmode() were called, via a callback, for some tvaudio chips.
There's just one callback code used on all those boards. So, it makes no
sense on keeping this as a callback.
Since there were some OOPS reported on tvaudio on kerneloops.org, this
patch removes this callback, adding the code at the only place were it
is called: inside chip_tread. A flag were added to indicate the need for
a kernel thread to set stereo mode on cards that needs it.
Using this more direct approach simplifies the code, making it more
robust against human errors.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Move DVB buffer transfer handling from irq handler to work_queue thread.
In order to properly lock the epu2cpu mailbox for driver to CX23418 commands,
the DVB/TS buffer handling needs to be moved from the IRQ handler and IRQ
context to a work queue. This work_queue implmentation is strikingly similar
to the ivtv implementation - for better or worse.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- touch only one register for brightness change
- no quality control
- don't probe again at streamon time.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the H flip and the R & B color inversion of mode 320x240.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Use correct Mailbox IRQ Ack values and misc IRQ handling cleanup.
The SCB field definitions for Ack IRQ's for mailboxes were inconsistent with
the bitmasks being loaded into those SCB fields and the SW2 Ack IRQ handling
logic. Renamed fields in SCB to make things consistent and did misc IRQ
handling cleanups: removing legacy ivtv dma_reg_lock, HPU IRQ flags, etc.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ok I made a patch that converts gspca kconfig file to a more standard=
one, with tabs + 2 white spaces, so that if a warning is added it still
compiles
please find it attached
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Mark CX18_CPU_DE_RELEASE_MDL as a slow API call.
Give the encoder time to complete the MDL release before destroying the
encoder internal task. This avoids an encoder lockup on the next digital
capture and error messages about buffers being returned for an inactive
encoder task handle.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Fix write retries for registers that always change - part 2.
Some registers, especially interrupt related ones, will never read
back the value just written. Modified interrupt register readback
checks to make sure the intended effect was achieved.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Final fix for when analogue only is selected
for compilation (ie, !CX88_DVB)
This tidies up previous fix and adds missing
de-alloc memory leak on fault (eg, if fe1 fails to alloc
where fe0 was allocated).
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Starts encoder not only on a read call but also on a poll command.
Signed-off-by: Frederic CAND <frederic.cand@anevia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ivtv used tvaudio in the past and at the time tvaudio required V4L1.
Since tvaudio is no longer dependent on V4L1 and since ivtv actually
no longer uses tvaudio at all, this is no removed from Kconfig.
Without this patch ivtv won't be build if V4L1 is disabled.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Disable write retries for registers that always change - part 1.
Interrupt related registers will likely not read back the value we just wrote.
Disable retries for these registers for now to avoid accidently discarding
interrupts. More intelligent read back verification criteria are needed for
these and other registers (e.g. GPIO line registers), which will be addressed in
subsequent changes.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Apparently the author of the saa7110 driver was confused by the
number of outputs returned by DECODER_GET_CAPABILITIES. Of course a
decoder chip has no analog ouputs, but it must have at least one
digital output.
* Fix an off-by-one error when checking the input value of
DECODER_SET_INPUT.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The attached patch fix VBI support cx88 card.
I'm running a capture for hours, getting the closed caption from it[1], and
it's working perfect - the output is the same of a bttv card.
Please apply this patch as soon as possible.
[1] - using zvbi-ntsc-cc of zvbi project.
Signed-off-by: Rafael Diniz <diniz@wimobilis.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There already is an report at kernel bugzilla about this issue:
http://bugzilla.kernel.org/show_bug.cgi?id=9455
When enabling extra checks for the i2c-bus of cx88 based cards by
loading i2c_algo_bit with bit_test=1 this may trigger an oops
when loading cx88_dvb.
This is caused by the extra check code that detects that the
sda-line is stuck high and thus does not register the i2c-bus.
cx88-dvb however does not check if the i2c-bus is valid and just
uses core->i2c_adap to attach dvb frontend modules.
This leads to an oops at the first call to i2c_transfer:
$ modprobe i2c_algo_bit bit_test=1
$ modprobe cx8802
cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
cx88[0]: quirk: PCIPCI_NATOMA -- set TBFX
cx88[0]: subsystem: 0070:9202, board: Hauppauge Nova-S-Plus DVB-S [card=37,autodetected], frontend(s): 1
cx88[0]: TV tuner type 4, Radio tuner type -1
cx88[0]: SDA stuck high!
cx88[0]: i2c register FAILED
input: cx88 IR (Hauppauge Nova-S-Plus as /class/input/input5
cx88[0]/2: cx2388x 8802 Driver Manager
cx88-mpeg driver manager 0000:00:10.2: enabling device (0154 -> 0156)
cx88-mpeg driver manager 0000:00:10.2: PCI INT A -> Link[LNKD] -> GSI 9 (level, low) -> IRQ 9
cx88[0]/2: found at 0000:00:10.2, rev: 5, irq: 9, latency: 64, mmio: 0xfb000000
cx8802_probe() allocating 1 frontend(s)
cx88/2: cx2388x dvb driver version 0.0.6 loaded
cx88/2: registering cx8802 driver, type: dvb access: shared
cx88[0]/2: subsystem: 0070:9202, board: Hauppauge Nova-S-Plus DVB-S [card=37]
cx88[0]/2: cx2388x based DVB/ATSC card
BUG: unable to handle kernel NULL pointer dereference at 00000000
IP: [<e084d4ef>] :i2c_core:i2c_transfer+0x1f/0x80
*pde = 00000000
Modules linked in: cx88_dvb(+) cx8802 cx88xx ir_common i2c_algo_bit tveeprom videobuf_dvb btcx_risc
mga drm ipv6 fscpos eeprom nfsd exportfs stv0299 b2c2_flexcop_pci b2c2_flexcop cx24123 s5h1420 ves1x93
dvb_ttpci dvb_core saa7146_vv saa7146 videobuf_dma_sg videobuf_core videodev v4l1_compat ttpci_eeprom
lirc_serial lirc_dev usbhid rtc uhci_hcd 8139too i2c_piix4 i2c_core usbcore evdev
Pid: 4249, comm: modprobe Not tainted (2.6.27-gentoo #3)
EIP: 0060:[<e084d4ef>] EFLAGS: 00010296 CPU: 0
EIP is at i2c_transfer+0x1f/0x80 [i2c_core]
EAX: 00000000 EBX: ffffffa1 ECX: 00000002 EDX: d6c71e3c
ESI: d80cd050 EDI: d8093c00 EBP: d6c71e20 ESP: d6c71e0c
DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Impact: driver could possibly stomp on resources outside of its scope
{mchehab@redhat.com: I got two versions of the same patch (identical,
except for whitespacing). One authored by Andy Burns and another
authored by Suresh Siddha. Due to that, I'm applying the one that has
less CodingStyle errors. I'm also adding both comments and the SOB's for
both patches, since they are both interesting}
Suresh Siddha commented:
Alexey Fisher reported:
> resource map sanity check conflict: 0xcfeff800 0xcff007ff 0xcfe00000
> 0xcfefffff PCI Bus 0000:01
BAR base is located in the middle of the 4K page and the hardcoded
size argument makes the request span two pages causing the conflict.
Fix the hard coded size argument in ioremap().
Andy Burns commented:
I have already sent this patch on the linux-dvb list, but it didn't get
much attention, so re-sending direct, I hope you all don't mind.
While attempting to run mythtv in a xen domU, I encountered problems
loading the driver for my saa7134 card, with an error from ioremap().
This error was due to the driver allocating an incorrectly sized mmio
area, which was trapped by xen's permission checks, but this would go
un-noticed on a kernel without xen.
My card has a 1K sized mmio area, I've had information that other cards
have 2K areas, perhaps others have different sizes, yet the driver
always attempts to map 4K. I realise that the granularity of mapping is
the page size, which typically would be 4K, but unless the card's base
address happens to fall on a 4K boundary (mine does not) then the
base+4K will end up spanning two pages, and this is when the error
occurs under xen.
My patch uses the pci_resource_len macro to determine the size required
for the user's particular card, instead of the hardcoded 4K value. I've
tested with a couple of printk() inside ioremap() that the start address
and size do get rounded to the closest page boundary.
With this patch I am able to successfully load the saa7134 driver and
run mythtv under xen with my card, subject to correct pollirq settings
in case of shared IRQ, I am still seeing occasional DMA panics, which I
think are related to swiotlb handling by dom0/domU, usually the panic
occurs when changing mux, once tuned to a mux, 12 hour continuous
recordings are possible without errors.
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andy Burns <andy@burns.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove lock_kernel() call from cafe_ccic.c
Commit d56dc61265 added lock_kernel()
calls to cafe_ccic.c. But that driver was written with proper locking
and does not need the BKL, so take it back out.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the missing compat ioctls that are needed to
operate Skype in combination with libv4l and a MJPEG only camera.
If you think it's trivial enough please submit it to -stable, too.
Signed-off-by: Gregor Jasny <gjasny@web.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by David Ellingsworth:
> I'm not sure if it matters or not, but the ibmcam driver in the
> Mauro's linux-2.6 git tree in the for_linus branch is currently
> broken.
uvd is equal to NULL during most of ibmcam_probe. Due to that, an OOPS is
generated at dev_info. This patch replaces uvd->dev->dev to dev->dev
inside this routine.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reviewed-by: David Ellingsworth <david@identd.dyndns.org>
This creates a self contained frontend de-allocator
for the instances where an adapter has not been
registered yet frontend de-allocation may
be required.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab