Add a simplefb template node for u-boot to further fill and activate.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a simplefb template node for u-boot to further fill and activate.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a simplefb template node for u-boot to further fill and activate.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele M9 has an ethernet board, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
PLL6 on sun6i has multiple outputs, just like the other sunxi platforms.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele M9 / A1000G quad has a blue status led, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele M9 / A1000G quad uses both usb-ports, one goes to an internal
usb wifi card, the other to a build-in usb-hub, so neither need their
OHCI companion controller to be enabled since the are always connected at
USB-2 speeds.
The controller which is attached to the wifi also does not need a vbus
regulator.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This avoids it getting briefly turned off between when the regulator getting
registered and the ahci driver turning it back on, thus avoiding the disk
going into emergency head park mode.
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cubietruck uses different pin for the USB OTG VBUS that
is why we override the one defined in sunxi-common-regulators.dtsi
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Until now the regulator nodes for powering USB VBUS
existed only for the two host controllers. Now the regulator
is added for USB OTG too.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the LeMaker Banana Pi, probing the external ethernet PHY connected
to the SoC's internal GMAC module sometimes fails. The PHY power
supply is handled via a GPIO-controlled regulator, and the existing
regulator startup-delay of 50000us is too short to make sure that the
PHY is always fully powered up when it is queried by phylib. Tests
have shown that to provide a reliable PHY detection, the startup-delay
has to be increased to at least 60000us. To have a certain safety margin
and to cater for manufacturing variations between different boards,
the delay gets set to 100000us as discussed on the linux-arm-kernel
mailinglist.
Signed-off-by: Karsten Merker <merker@debian.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Roman Byshko <rbyshko@gmail.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Zoltan HERPAI <wigyori@uid0.hu>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Zoltan HERPAI <wigyori@uid0.hu>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: FUKAUMI Naoki <naobsd@gmail.com>
The A80 Optimus board exposes uart4 on the GPIO expansion header.
Enable it so we can use it.
Also enable the internal pull-ups, as there doesn't seem to be
external pull-up resistors for pins on the expansion header.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
uart4 only has one possible pinmux setting on the A80 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 Optimus board has 3 usable LEDs that are controlled via GPIO.
This patch adds support for 2 of them which are driver by GPIOs in the
main pin controller. The remaining one uses GPIO from the R_PIO
controller, which we don't support yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
i2c3 is exposed on the GPIO extension header. Enable it so we can use it.
Also enable internal pull-ups on the pins, as they don't seem to have
external pull-up resistors.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
i2c3 has only one possible pinmux setting on the A80 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 has 5 i2c controllers in the main processor block.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the UART0 muxing, as set up by the bootloader.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The A80 pinctrl driver is just as usual our pinctrl/gpio/external interrupt
controller.
Nothing really out of the extraordinary here...
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Roman Byshko <rbyshko@gmail.com>
During the GPL to GPL/X11 licensing migration, the GPL notice introduced
mentionned the device trees as a library, which is not really accurate. It
began to spread by copy and paste. Fix all these library mentions to reflect
the file that it's actually just a file.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Now that we have driver support for the basic clocks, add them to the
dtsi and update existing peripherals. Also add reset controls to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The A80 Optimus Board is was launched with the Allwinner A80 SoC.
It was jointly developed by Allwinner and Merrii.
This board has a UART port, a JTAG connector, USB host ports, a USB
3.0 OTG connector, an HDMI output, a micro SD slot, 8G NAND flash,
4G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone
jack, IR receiver, and additional GPIO headers.
This patch adds only basic support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Andreas Färber <afaerber@suse.de>
The Allwinner A80 is a new multi-purpose SoC with 4 Cortex-A7 and
4 Cortex-A15 cores in a big.LITTLE architecture, and a 64-core
PowerVR G6230 GPU.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Andreas Färber <afaerber@suse.de>
This adds support for the Olimex A20-OLinuXino-Lime2
https://www.olimex.com/Products/OLinuXino/A20/A20-OLinuXIno-LIME2
Differences to previous Lime boards are 1GB RAM and gigabit ethernet
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele M3 is yet another Allwinnner based Android top set box from Mele.
It uses a housing similar to the A2000, but without the USM sata storage slot
at the top.
It features an A20 SoC, 1G RAM, 4G eMMC (unique for Allwinner devices),
100Mbit ethernet, HDMI out, 3 USB A receptacles, VGA, and A/V OUT connections.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Banana Pi is an A20 based development board using Raspberry Pi compatible
IO headers. It comes with 1 GB RAM, 1 Gb ethernet, 2x USB host, sata, hdmi
and stereo audio out + various expenansion headers:
http://www.lemaker.org/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede