Commit Graph

617 Commits

Author SHA1 Message Date
NeilBrown 1757128438 [PATCH] md: assorted md and raid1 one-liners
Fix few bugs that meant that:
  - superblocks weren't alway written at exactly the right time (this
    could show up if the array was not written to - writting to the array
    causes lots of superblock updates and so hides these errors).

  - restarting device recovery after a clean shutdown (version-1 metadata
    only) didn't work as intended (or at all).

1/ Ensure superblock is updated when a new device is added.
2/ Remove an inappropriate test on MD_RECOVERY_SYNC in md_do_sync.
   The body of this if takes one of two branches depending on whether
   MD_RECOVERY_SYNC is set, so testing it in the clause of the if
   is wrong.
3/ Flag superblock for updating after a resync/recovery finishes.
4/ If we find the neeed to restart a recovery in the middle (version-1
   metadata only) make sure a full recovery (not just as guided by
   bitmaps) does get done.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10 09:57:21 -08:00
NeilBrown c2b00852fb [PATCH] md: return a non-zero error to bi_end_io as appropriate in raid5
Currently raid5 depends on clearing the BIO_UPTODATE flag to signal an error
to higher levels.  While this should be sufficient, it is safer to explicitly
set the error code as well - less room for confusion.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10 09:57:21 -08:00
NeilBrown b8c6b64556 [PATCH] md: remove some old ifdefed-out code from raid5.c
There are some vestiges of old code that was used for bypassing the stripe
cache on reads in raid5.c.  This was never updated after the change from
buffer_heads to bios, but was left as a reminder.

That functionality has nowe been implemented in a completely different way, so
the old code can go.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10 09:57:21 -08:00
Jeff Garzik fdee8ae449 [PATCH] MD: conditionalize some code
The autorun code is only used if this module is built into the static
kernel image.  Adjust #ifdefs accordingly.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10 09:57:21 -08:00
NeilBrown b875e531fc [PATCH] md: fix innocuous bug in raid6 stripe_to_pdidx
stripe_to_pdidx finds the index of the parity disk for a given stripe.  It
assumes raid5 in that it uses "disks-1" to determine the number of data disks.

This is incorrect for raid6 but fortunately the two usages cancel each other
out.  The only way that 'data_disks' affects the calculation of pd_idx in
raid5_compute_sector is when it is divided into the sector number.  But as
that sector number is calculated by multiplying in the wrong value of
'data_disks' the division produces the right value.

So it is innocuous but needs to be fixed.

Also change the calculation of raid_disks in compute_blocknr to make it
more obviously correct (it seems at first to always use disks-1 too).

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10 09:57:21 -08:00
Raz Ben-Jehuda(caro) 5248861511 [PATCH] md: enable bypassing cache for reads
Call the chunk_aligned_read where appropriate.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10 09:57:20 -08:00
Raz Ben-Jehuda(caro) 46031f9a38 [PATCH] md: allow reads that have bypassed the cache to be retried on failure
If a bypass-the-cache read fails, we simply try again through the cache.  If
it fails again it will trigger normal recovery precedures.

update 1:

From: NeilBrown <neilb@suse.de>

1/
  chunk_aligned_read and retry_aligned_read assume that
      data_disks == raid_disks - 1
  which is not true for raid6.
  So when an aligned read request bypasses the cache, we can get the wrong data.

2/ The cloned bio is being used-after-free in raid5_align_endio
   (to test BIO_UPTODATE).

3/ We forgot to add rdev->data_offset when submitting
   a bio for aligned-read

4/ clone_bio calls blk_recount_segments and then we change bi_bdev,
   so we need to invalidate the segment counts.

5/ We don't de-reference the rdev when the read completes.
   This means we need to record the rdev to so it is still
   available in the end_io routine.  Fortunately
   bi_next in the original bio is unused at this point so
   we can stuff it in there.

6/ We leak a cloned bio if the target rdev is not usable.

From: NeilBrown <neilb@suse.de>

update 2:

1/ When aligned requests fail (read error) they need to be retried
   via the normal method (stripe cache).  As we cannot be sure that
   we can process a single read in one go (we may not be able to
   allocate all the stripes needed) we store a bio-being-retried
   and a list of bioes-that-still-need-to-be-retried.
   When find a bio that needs to be retried, we should add it to
   the list, not to single-bio...

2/ We were never incrementing 'scnt' when resubmitting failed
   aligned requests.

[akpm@osdl.org: build fix]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10 09:57:20 -08:00
Raz Ben-Jehuda(caro) f679623f50 [PATCH] md: handle bypassing the read cache (assuming nothing fails)
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10 09:57:20 -08:00
Raz Ben-Jehuda(caro) 23032a0eb9 [PATCH] md: define raid5_mergeable_bvec
This will encourage read request to be on only one device, so we will often be
able to bypass the cache for read requests.

Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10 09:57:20 -08:00
NeilBrown 0d4ca600fc [PATCH] md: tidy up device-change notification when an md array is stopped
An md array can be stopped leaving all the setting still in place, or it can
torn down and destroyed.  set_capacity and other change notifications only
happen in the latter case, but should happen in both.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10 09:57:20 -08:00
Adrian Bunk c642f9e03b [PATCH] make drivers/md/dm-snap.c:ksnapd static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:09 -08:00
Jonathan E Brassow 88b20a1a71 [PATCH] dm: raid1: reset sync_search on resume
Reset sync_search on resume.  The effect is to retry syncing all out-of-sync
regions when a mirror is resumed, including ones that previously failed.

Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:09 -08:00
Jonathan E Brassow f3ee6b2f62 [PATCH] dm: log: rename complete_resync_work
The complete_resync_work function only provides the ability to change an
out-of-sync region to in-sync.  This patch enhances the function to allow us
to change the status from in-sync to out-of-sync as well, something that is
needed when a mirror write to one of the devices or an initial resync on a
given region fails.

Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:09 -08:00
Milan Broz 31c93a0c29 [PATCH] dm: snapshot: abstract memory release
Move the code that releases memory used by a snapshot into a separate function.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:09 -08:00
Kiyoshi Ueda 45e157206c [PATCH] dm: mpath: use noflush suspending
Implement the pushback feature for the multipath target.

The pushback request is used when:
  1) there are no valid paths;
  2) queue_if_no_path was set;
  3) a suspend is being issued with the DMF_NOFLUSH_SUSPENDING flag.
     Otherwise bios are returned to applications with -EIO.

To check whether queue_if_no_path is specified or not, you need to check
both queue_if_no_path and saved_queue_if_no_path, because presuspend saves
the original queue_if_no_path value to saved_queue_if_no_path.

The check for 1 already exists in both map_io() and do_end_io().
So this patch adds __must_push_back() to check 2 and 3.

Test results:
See the test results in the preceding patch.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:09 -08:00
Kiyoshi Ueda 2e93ccc193 [PATCH] dm: suspend: add noflush pushback
In device-mapper I/O is sometimes queued within targets for later processing.
For example the multipath target can be configured to store I/O when no paths
are available instead of returning it -EIO.

This patch allows the device-mapper core to instruct a target to transfer the
contents of any such in-target queue back into the core.  This frees up the
resources used by the target so the core can replace that target with an
alternative one and then resend the I/O to it.  Without this patch the only
way to change the target in such circumstances involves returning the I/O with
an error back to the filesystem/application.  In the multipath case, this
patch will let us add new paths for existing I/O to try after all the existing
paths have failed.

    DMF_NOFLUSH_SUSPENDING
    ----------------------

If the DM_NOFLUSH_FLAG ioctl option is specified at suspend time, the
DMF_NOFLUSH_SUSPENDING flag is set in md->flags during dm_suspend().  It
is always cleared before dm_suspend() returns.

The flag must be visible while the target is flushing pending I/Os so it
is set before presuspend where the flush starts and unset after the wait
for md->pending where the flush ends.

Target drivers can check this flag by calling dm_noflush_suspending().

    DM_MAPIO_REQUEUE / DM_ENDIO_REQUEUE
    -----------------------------------

A target's map() function can now return DM_MAPIO_REQUEUE to request the
device mapper core queue the bio.

Similarly, a target's end_io() function can return DM_ENDIO_REQUEUE to request
the same.  This has been labelled 'pushback'.

The __map_bio() and clone_endio() functions in the core treat these return
values as errors and call dec_pending() to end the I/O.

    dec_pending
    -----------

dec_pending() saves the pushback request in struct dm_io->error.  Once all
the split clones have ended, dec_pending() will put the original bio on
the md->pushback list.  Note that this supercedes any I/O errors.

It is possible for the suspend with DM_NOFLUSH_FLAG to be aborted while
in progress (e.g. by user interrupt).  dec_pending() checks for this and
returns -EIO if it happened.

    pushdback list and pushback_lock
    --------------------------------

The bio is queued on md->pushback temporarily in dec_pending(), and after
all pending I/Os return, md->pushback is merged into md->deferred in
dm_suspend() for re-issuing at resume time.

md->pushback_lock protects md->pushback.
The lock should be held with irq disabled because dec_pending() can be
called from interrupt context.

Queueing bios to md->pushback in dec_pending() must be done atomically
with the check for DMF_NOFLUSH_SUSPENDING flag.  So md->pushback_lock is
held when checking the flag.  Otherwise dec_pending() may queue a bio to
md->pushback after the interrupted dm_suspend() flushes md->pushback.
Then the bio would be left in md->pushback.

Flag setting in dm_suspend() can be done without md->pushback_lock because
the flag is checked only after presuspend and the set value is already
made visible via the target's presuspend function.

The flag can be checked without md->pushback_lock (e.g. the first part of
the dec_pending() or target drivers), because the flag is checked again
with md->pushback_lock held when the bio is really queued to md->pushback
as described above.  So even if the flag is cleared after the lockless
checkings, the bio isn't left in md->pushback but returned to applications
with -EIO.

    Other notes on the current patch
    --------------------------------

- md->pushback is added to the struct mapped_device instead of using
  md->deferred directly because md->io_lock which protects md->deferred is
  rw_semaphore and can't be used in interrupt context like dec_pending(),
  and md->io_lock protects the DMF_BLOCK_IO flag of md->flags too.

- Don't issue lock_fs() in dm_suspend() if the DM_NOFLUSH_FLAG
  ioctl option is specified, because I/Os generated by lock_fs() would be
  pushed back and never return if there were no valid devices.

- If an error occurs in dm_suspend() after the DMF_NOFLUSH_SUSPENDING
  flag is set, md->pushback must be flushed because I/Os may be queued to
  the list already.  (flush_and_out label in dm_suspend())

    Test results
    ------------

I have tested using multipath target with the next patch.

The following tests are for regression/compatibility:
  - I/Os succeed when valid paths exist;
  - I/Os fail when there are no valid paths and queue_if_no_path is not
    set;
  - I/Os are queued in the multipath target when there are no valid paths and
    queue_if_no_path is set;
  - The queued I/Os above fail when suspend is issued without the
    DM_NOFLUSH_FLAG ioctl option.  I/Os spanning 2 multipath targets also
    fail.

The following tests are for the normal code path of new pushback feature:
  - Queued I/Os in the multipath target are flushed from the target
    but don't return when suspend is issued with the DM_NOFLUSH_FLAG
    ioctl option;
  - The I/Os above are queued in the multipath target again when
    resume is issued without path recovery;
  - The I/Os above succeed when resume is issued after path recovery
    or table load;
  - Queued I/Os in the multipath target succeed when resume is issued
    with the DM_NOFLUSH_FLAG ioctl option after table load. I/Os
    spanning 2 multipath targets also succeed.

The following tests are for the error paths of the new pushback feature:
  - When the bdget_disk() fails in dm_suspend(), the
    DMF_NOFLUSH_SUSPENDING flag is cleared and I/Os already queued to the
    pushback list are flushed properly.
  - When suspend with the DM_NOFLUSH_FLAG ioctl option is interrupted,
      o I/Os which had already been queued to the pushback list
        at the time don't return, and are re-issued at resume time;
      o I/Os which hadn't been returned at the time return with EIO.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:09 -08:00
Kiyoshi Ueda 81fdb096db [PATCH] dm: ioctl: add noflush suspend
Provide a dm ioctl option to request noflush suspending.  (See next patch for
what this is for.) As the interface is extended, the version number is
incremented.

Other than accepting the new option through the interface, There is no change
to existing behaviour.

Test results:
Confirmed the option is given from user-space correctly.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:09 -08:00
Kiyoshi Ueda d2a7ad29a8 [PATCH] dm: map and endio symbolic return codes
Update existing targets to use the new symbols for return values from target
map and end_io functions.

There is no effect on behaviour.

Test results:
Done build test without errors.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:09 -08:00
Kiyoshi Ueda 45cbcd7983 [PATCH] dm: map and endio return code clarification
Tighten the use of return values from the target map and end_io functions.
Values of 2 and above are now explictly reserved for future use.  There are no
existing targets using such values.

The patch has no effect on existing behaviour.

o Reserve return values of 2 and above from target map functions.
  Any positive value currently indicates "mapping complete", but all
  existing drivers use the value 1.  We now make that a requirement
  so we can assign new meaning to higher values in future.

  The new definition of return values from target map functions is:
      < 0 : error
      = 0 : The target will handle the io (DM_MAPIO_SUBMITTED).
      = 1 : Mapping completed (DM_MAPIO_REMAPPED).
      > 1 : Reserved (undefined).  Previously this was the same as '= 1'.

o Reserve return values of 2 and above from target end_io functions
  for similar reasons.
  DM_ENDIO_INCOMPLETE is introduced for a return value of 1.

Test results:

  I have tested by using the multipath target.

  I/Os succeed when valid paths exist.

  I/Os are queued in the multipath target when there are no valid paths and
queue_if_no_path is set.

  I/Os fail when there are no valid paths and queue_if_no_path is not set.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:09 -08:00
Kiyoshi Ueda a3d77d35be [PATCH] dm: suspend: parameter change
Change the interface of dm_suspend() so that we can pass several options
without increasing the number of parameters.  The existing 'do_lockfs' integer
parameter is replaced by a flag DM_SUSPEND_LOCKFS_FLAG.

There is no functional change to the code.

Test results:
I have tested 'dmsetup suspend' command with/without the '--nolockfs'
option and confirmed the do_lockfs value is correctly set.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:09 -08:00
Kiyoshi Ueda 7485936463 [PATCH] dm: tidy core formatting
Remove unnecessary spaces in dm.c.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:08 -08:00
Heinz Mauelshagen f00b16ad66 [PATCH] dm io: fix bi_max_vecs
The existing code allocates an extra slot in bi_io_vec[] and uses it to store
the region number.

This patch hides the extra slot from bio_add_page() so the region number can't
get overwritten.

Also remove a hard-coded SECTOR_SHIFT and fix a typo in a comment.

Signed-off-by: Heinz Mauelshagen <hjm@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Milan Broz <mbroz@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:08 -08:00
David Howells f0d1b0b30d [PATCH] LOG2: Implement a general integer log2 facility in the kernel
This facility provides three entry points:

	ilog2()		Log base 2 of unsigned long
	ilog2_u32()	Log base 2 of u32
	ilog2_u64()	Log base 2 of u64

These facilities can either be used inside functions on dynamic data:

	int do_something(long q)
	{
		...;
		y = ilog2(x)
		...;
	}

Or can be used to statically initialise global variables with constant values:

	unsigned n = ilog2(27);

When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant.  They treat negative numbers as
unsigned.

When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.

[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:28:51 -08:00
Josef Sipek c649bb9c55 [PATCH] struct path: convert md
Signed-off-by: Josef Sipek <jsipek@fsl.cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:28:47 -08:00
Josef "Jeff" Sipek c922d5f7f5 [PATCH] struct path: rename DM's struct path
Rename DM's struct path to struct dm_path to prevent name collision between it
and struct path from fs/namei.c.

Signed-off-by: Josef "Jeff" Sipek <jsipek@cs.sunysb.edu>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: <reiserfs-dev@namesys.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:28:40 -08:00
NeilBrown d63a5a74de [PATCH] lockdep: avoid lockdep warning in md
md_open takes ->reconfig_mutex which causes lockdep to complain.  This
(normally) doesn't have deadlock potential as the possible conflict is with a
reconfig_mutex in a different device.

I say "normally" because if a loop were created in the array->member hierarchy
a deadlock could happen.  However that causes bigger problems than a deadlock
and should be fixed independently.

So we flag the lock in md_open as a nested lock.  This requires defining
mutex_lock_interruptible_nested.

Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:28:39 -08:00
Peter Zijlstra 2e7b651df1 [PATCH] remove the old bd_mutex lockdep annotation
Remove the old complex and crufty bd_mutex annotation.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:28:38 -08:00
Linus Torvalds 2685b267bc Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (48 commits)
  [NETFILTER]: Fix non-ANSI func. decl.
  [TG3]: Identify Serdes devices more clearly.
  [TG3]: Use msleep.
  [TG3]: Use netif_msg_*.
  [TG3]: Allow partial speed advertisement.
  [TG3]: Add TG3_FLG2_IS_NIC flag.
  [TG3]: Add 5787F device ID.
  [TG3]: Fix Phy loopback.
  [WANROUTER]: Kill kmalloc debugging code.
  [TCP] inet_twdr_hangman: Delete unnecessary memory barrier().
  [NET]: Memory barrier cleanups
  [IPSEC]: Fix inetpeer leak in ipv4 xfrm dst entries.
  audit: disable ipsec auditing when CONFIG_AUDITSYSCALL=n
  audit: Add auditing to ipsec
  [IRDA] irlan: Fix compile warning when CONFIG_PROC_FS=n
  [IrDA]: Incorrect TTP header reservation
  [IrDA]: PXA FIR code device model conversion
  [GENETLINK]: Fix misplaced command flags.
  [NETLIK]: Add a pointer to the Generic Netlink wiki page.
  [IPV6] RAW: Don't release unlocked sock.
  ...
2006-12-07 09:05:15 -08:00
Nigel Cunningham 7dfb71030f [PATCH] Add include/linux/freezer.h and move definitions from sched.h
Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.

[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:27 -08:00
Christoph Lameter e18b890bb0 [PATCH] slab: remove kmem_cache_t
Replace all uses of kmem_cache_t with struct kmem_cache.

The patch was generated using the following script:

	#!/bin/sh
	#
	# Replace one string by another in all the kernel sources.
	#

	set -e

	for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
		quilt add $file
		sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
		mv /tmp/$$ $file
		quilt refresh
	done

The script was run like this

	sh replace kmem_cache_t "struct kmem_cache"

Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:25 -08:00
Herbert Xu 79066ad32b [CRYPTO] dm-crypt: Make iv_gen_private a union
Rather than stuffing integers into pointers with casts, let's use
a union.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-12-06 18:39:01 -08:00
Herbert Xu 45789328e5 [BLOCK] dm-crypt: Align IV to u64 for essiv
This patch makes the IV u64-aligned since essiv does a u64 store to it.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2006-12-06 18:38:48 -08:00
Rik Snel 48527fa7cf [BLOCK] dm-crypt: benbi IV, big endian narrow block count for LRW-32-AES
LRW-32-AES needs a certain IV. This IV should be provided dm-crypt.
The block cipher mode could, in principle generate the correct IV from
the plain IV, but I think that it is cleaner to supply the right IV
directly.

The sector -> narrow block calculation uses a shift for performance reasons.
This shift is computed in .ctr and stored in cc->iv_gen_private (as a void *).

Signed-off-by: Rik Snel <rsnel@cube.dyndns.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2006-12-06 18:38:47 -08:00
David Howells c4028958b6 WorkStruct: make allyesconfig
Fix up for make allyesconfig.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-11-22 14:57:56 +00:00
Rafael J. Wysocki 4b438a23fb [PATCH] md: do not freeze md threads for suspend
If there's a swap file on a software RAID, it should be possible to use this
file for saving the swsusp's suspend image.  Also, this file should be
available to the memory management subsystem when memory is being freed before
the suspend image is created.

For the above reasons it seems that md_threads should not be frozen during the
suspend and the appended patch makes this happen, but then there is the
question if they don't cause any data to be written to disks after the suspend
image has been created, provided that all filesystems are frozen at that time.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-08 18:29:24 -08:00
NeilBrown 0692c6b1cf [PATCH] md: fix sizing problem with raid5-reshape and CONFIG_LBD=n
I forgot to has the size-in-blocks to (loff_t) before shifting up to a
size-in-bytes.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-08 18:29:24 -08:00
NeilBrown 2f47130361 [PATCH] md: change ONLINE/OFFLINE events to a single CHANGE event
It turns out that CHANGE is preferred to ONLINE/OFFLINE for various reasons
(not least of which being that udev understands it already).

So remove the recently added KOBJ_OFFLINE (no-one is likely to care anyway)
and change the ONLINE to a CHANGE event

Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-08 18:29:23 -08:00
Jonathan E Brassow 33184048dc [PATCH] dm: raid1: fix waiting for io on suspend
All device-mapper targets must complete outstanding I/O before suspending.
The mirror target generates I/O in its recovery phase and fails to wait for
it.  It needs to be tracked so we can ensure that it has completed before we
suspend.

[akpm@osdl.org: cleanup]
Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <dm-devel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-08 18:29:23 -08:00
Jonathan E Brassow 5d55fdf949 [PATCH] dm: multipath: fix rr_add_path order
When adding paths to the round-robin path selector, their order gets inverted,
which is not desirable.

Fix by replacing list_add() with list_add_tail().

Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <dm-devel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-08 18:29:23 -08:00
Alasdair G Kergon d287483d6d [PATCH] dm: suspend: fix error path
If the device is already suspended, just return the error and skip the code
that would incorrectly wipe md->suspended_bdev.

(This isn't currently a problem because existing code avoids calling this
function if the device is already suspended.)

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <dm-devel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-08 18:29:23 -08:00
Alasdair G Kergon bfc5ecdf48 [PATCH] dm: fix find_device race
There is a race between dev_create() and find_device().

If the mdptr has not yet been stored against a device, find_device() needs to
behave as though no device was found.  It already returns NULL, but there is a
dm_put() missing: it must drop the reference dm_get_md() took.

The bug was introduced by dm-fix-mapped-device-ref-counting.patch.

It manifests itself if another dm ioctl attempts to reference a newly-created
device while the device creation ioctl is still running.  The consequence is
that the device cannot be removed until the machine is rebooted.  Certain udev
configurations can lead to this happening.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <dm-devel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-08 18:29:23 -08:00
NeilBrown 7870db4c7f [PATCH] md: send online/offline uevents when an md array starts/stops
This allows udev to do something intelligent when an array becomes
available.

Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-11-03 12:27:55 -08:00
Christophe Saout 37af6560f7 [PATCH] Fix dmsetup table output change
Fix dm-crypt after the block cipher API changes to correctly return the
backwards compatible cipher-chainmode[-ivmode] format for "dmsetup
table".

Signed-off-by: Christophe Saout <christophe@saout.de>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

diff linux-2.6.19-rc3.orig/drivers/md/dm-crypt.c linux-2.6.19-rc3/drivers/md/dm-crypt.c
2006-10-30 12:02:57 -08:00
Randy Dunlap 969b755aad [PATCH] md: fix printk format warnings, seen on powerpc64:
drivers/md/raid1.c:1479: warning: long long unsigned int format, long unsigned int arg (arg 4)
drivers/md/raid10.c:1475: warning: long long unsigned int format, long unsigned int arg (arg 4)

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-28 11:30:52 -07:00
NeilBrown 750a8f3e8f [PATCH] md: fix up maintenance of ->degraded in multipath
A recent fix which made sure ->degraded was initialised properly exposed a
second bug - ->degraded wasn't been updated when drives failed or were
hot-added.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-28 11:30:51 -07:00
NeilBrown 01ab5662f5 [PATCH] md: simplify checking of available size when resizing an array
When "mdadm --grow --size=xxx" is used to resize an array (use more or less of
each device), we check the new siza against the available space in each
device.

We already have that number recorded in rdev->size, so calculating it is
pointless (and wrong in one obscure case).

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-28 11:30:51 -07:00
NeilBrown 2b6e845986 [PATCH] md: fix bug where spares don't always get rebuilt properly when they become live
If save_raid_disk is >= 0, then the device could be a device that is already
in sync that is being re-added.  So we need to default this value to -1.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-28 11:30:51 -07:00
NeilBrown 4f2e639af4 [PATCH] md: endian annotations for the bitmap superblock
And a couple of bug fixes found by sparse.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-21 13:35:05 -07:00
NeilBrown 1c05b4bc22 [PATCH] md: endian annotation for v1 superblock access
Includes a couple of bugfixes found by sparse.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-21 13:35:05 -07:00
NeilBrown 2e333e8986 [PATCH] md: fix calculation of ->degraded for multipath and raid10
Two less-used md personalities have bugs in the calculation of ->degraded (the
extent to which the array is degraded).

Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-21 13:35:05 -07:00
Andrew Morton 3fcfab16c5 [PATCH] separate bdi congestion functions from queue congestion functions
Separate out the concept of "queue congestion" from "backing-dev congestion".
Congestion is a backing-dev concept, not a queue concept.

The blk_* congestion functions are retained, as wrappers around the core
backing-dev congestion functions.

This proper layering is needed so that NFS can cleanly use the congestion
functions, and so that CONFIG_BLOCK=n actually links.

Cc: "Thomas Maier" <balagi@justmail.de>
Cc: "Jens Axboe" <jens.axboe@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: David Howells <dhowells@redhat.com>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-20 10:26:35 -07:00
Akinobu Mita e24650c2e7 [PATCH] md: fix /proc/mdstat refcounting
I have seen mdadm oops after successfully unloading md module.

This patch privents from unloading md module while
mdadm is polling /proc/mdstat.

Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Akinbou Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-17 08:18:43 -07:00
Alexey Dobriyan 5f6e3c8365 [PATCH] md: use BUILD_BUG_ON
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-11 11:14:26 -07:00
NeilBrown 5842730de1 [PATCH] md: fix bug where new drives added to an md array sometimes don't sync properly
This fixes a bug introduced in 2.6.18.

If a drive is added to a raid1 using older tools (mdadm-1.x or raidtools)
then it will be included in the array without any resync happening.

It has been submitted for 2.6.18.1.

Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-06 08:53:41 -07:00
Eric Sesterhenn 52e5f9d1cf BUG_ON cleanup for drivers/md/
This changes two if() BUG(); usages to BUG_ON(); so people
can disable it safely.

Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-10-03 23:33:23 +02:00
NeilBrown 3a0f5bbb1a [PATCH] md: add error reporting to superblock write failure
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:19 -07:00
Paul Clements a638b2dc95 [PATCH] md: use ffz instead of find_first_set to convert multiplier to shift
find_first_set doesn't find the least-significant bit on bigendian machines,
so it is really wrong to use it.

ffs is closer, but takes an 'int' and we have a 'unsigned long'.  So use
ffz(~X) to convert a chunksize into a chunkshift.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:18 -07:00
NeilBrown 14f50b49fd [PATCH] md: remove 'experimental' classification from raid5 reshape
I have had enough success reports not to believe that this is safe for 2.6.19.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:18 -07:00
NeilBrown e8703fe1f5 [PATCH] md: remove MAX_MD_DEVS which is an arbitrary limit
Once upon a time we needed to fixed limit to the number of md devices,
probably because we preallocated some array.  This need no longer exists, but
we still have an arbitrary limit.

So remove MAX_MD_DEVS and allow as many devices as we can fit into the 'minor'
part of a device number.

Also remove some useless noise at init time (which reports MAX_MD_DEVS) and
remove MD_THREAD_NAME_MAX which hasn't been used for a while.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:18 -07:00
NeilBrown 61df9d91e9 [PATCH] md: make messages about resync/recovery etc more specific
It is possible to request a 'check' of an md/raid array where the whole array
is read and consistancies are reported.

This uses the same mechanisms as 'resync' and so reports in the kernel logs
that a resync is being started.  This understandably confuses/worries people.

Also the text in /proc/mdstat suggests a 'resync' is happen when it is just a
check.

This patch changes those messages to be more specific about what is happening.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:18 -07:00
NeilBrown f022b2fddd [PATCH] md: add a ->congested_fn function for raid5/6
This is very different from other raid levels and all requests go through a
'stripe cache', and it has congestion management already.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:18 -07:00
NeilBrown 0d12922823 [PATCH] md: define ->congested_fn for raid1, raid10, and multipath
raid1, raid10 and multipath don't report their 'congested' status through
bdi_*_congested, but should.

This patch adds the appropriate functions which just check the 'congested'
status of all active members (with appropriate locking).

raid1 read_balance should be modified to prefer devices where
bdi_read_congested returns false.  Then we could use the '&' branch rather
than the '|' branch.  However that should would need some benchmarking first
to make sure it is actually a good idea.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:18 -07:00
NeilBrown 26be34dc3a [PATCH] md: define backing_dev_info.congested_fn for raid0 and linear
Each backing_dev needs to be able to report whether it is congested, either by
modulating BDI_*_congested in ->state, or by defining a ->congested_fn.
md/raid did neither of these.  This patch add a congested_fn which simply
checks all component devices to see if they are congested.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:18 -07:00
NeilBrown c04be0aa82 [PATCH] md: Improve locking around error handling
The error handling routines don't use proper locking, and so two concurrent
errors could trigger a problem.

So:
  - use test-and-set and test-and-clear to synchonise
    the In_sync bits with the ->degraded count
  - use the spinlock to protect updates to the
    degraded count (could use an atomic_t but that
    would be a bigger change in code, and isn't
    really justified)
  - remove un-necessary locking in raid5

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:18 -07:00
NeilBrown 11ce99e625 [PATCH] md: Remove working_disks from raid1 state data
It is equivalent to conf->raid_disks - conf->mddev->degraded.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:17 -07:00
NeilBrown 867868fb55 [PATCH] md: Factor out part of raid1d into a separate function
raid1d has toooo many nested block, so take the fix_read_error functionality
out into a separate function.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:17 -07:00
Coywolf Qi Hunt 2d2063ceae [PATCH] md: remove unnecessary variable x in stripe_to_pdidx()
Signed-off-by: Coywolf Qi Hunt <qiyong@freeforge.net>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:17 -07:00
Paul Clements 9b1d1dac18 [PATCH] md: new sysfs interface for setting bits in the write-intent-bitmap
Add a new sysfs interface that allows the bitmap of an array to be dirtied.
The interface is write-only, and is used as follows:

echo "1000" > /sys/block/md2/md/bitmap

(dirty the bit for chunk 1000 [offset 0] in the in-memory and on-disk
bitmaps of array md2)

echo "1000-2000" > /sys/block/md1/md/bitmap

(dirty the bits for chunks 1000-2000 in md1's bitmap)

This is useful, for example, in cluster environments where you may need to
combine two disjoint bitmaps into one (following a server failure, after a
secondary server has taken over the array).  By combining the bitmaps on
the two servers, a full resync can be avoided (This was discussed on the
list back on March 18, 2005, "[PATCH 1/2] md bitmap bug fixes" thread).

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:17 -07:00
NeilBrown 76186dd8b7 [PATCH] md: remove 'working_disks' from raid10 state
It isn't needed as mddev->degraded contains equivalent info.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:17 -07:00
NeilBrown 02c2de8cc8 [PATCH] md: remove the working_disks and failed_disks from raid5 state data.
They are not needed.  conf->failed_disks is the same as mddev->degraded and
conf->working_disks is conf->raid_disks - mddev->degraded.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:17 -07:00
NeilBrown 850b2b420c [PATCH] md: replace magic numbers in sb_dirty with well defined bit flags
Instead of magic numbers (0,1,2,3) in sb_dirty, we have
some flags instead:
MD_CHANGE_DEVS
   Some device state has changed requiring superblock update
   on all devices.
MD_CHANGE_CLEAN
   The array has transitions from 'clean' to 'dirty' or back,
   requiring a superblock update on active devices, but possibly
   not on spares
MD_CHANGE_PENDING
   A superblock update is underway.

We wait for an update to complete by waiting for all flags to be clear.  A
flag can be set at any time, even during an update, without risk that the
change will be lost.

Stop exporting md_update_sb - isn't needed.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:17 -07:00
NeilBrown 6814d5368d [PATCH] md: factor out part of raid10d into a separate function.
raid10d has toooo many nested block, so take the fix_read_error functionality
out into a separate function.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:17 -07:00
Adrian Bunk fbedac04fa [PATCH] md: the scheduled removal of the START_ARRAY ioctl for md
This patch contains the scheduled removal of the START_ARRAY ioctl for md.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:16 -07:00
Bryn Reeves 999d816851 [PATCH] dm table: add target flush
This patch adds support for a per-target dm_flush_fn method.  This is needed
to allow dm-loop to invalidate page cache mappings in response to BLKFLSBUF
ioctl commands.

Signed-off-by: Bryn Reeves <breeves@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:16 -07:00
Bryn Reeves 3cb4021453 [PATCH] dm: extract device limit setting
Separate the setting of device I/O limits from dm_get_device().  dm-loop will
use this.

Signed-off-by: Bryn Reeves <breeves@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:16 -07:00
Stefan Bader 9faf400f7e [PATCH] dm: use private biosets
I found a problem within device-mapper that occurs in low-mem situations.  It
was found using a mirror target but I think in theory it would hit any setup
that stacks device-mapper devices (like LVM on top of multipath).

Since device-mapper core uses the common fs_bioset in clone_bio(), and a
private, but still global, bio_set in split_bvec() it is possible that the
filesystem and the first level target successfully get bios but the lower
level target doesn't because there is no more memory and the pool was drained
by upper layers.  So the remapping will be stuck forever.  To solve this
device-mapper core needs to use a private bio_set for each device.

Signed-off-by: Stefan Bader <Stefan.Bader@de.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:16 -07:00
Milan Broz 6a24c71843 [PATCH] dm crypt: use private biosets
In the low memory situation dm-crypt needs to use a private mempool of bios to
avoid blocking.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:16 -07:00
Milan Broz 23541d2d28 [PATCH] dm crypt: move io to workqueue
This patch is designed to help dm-crypt comply with the
new constraints imposed by the following patch in -mm:
  md-dm-reduce-stack-usage-with-stacked-block-devices.patch

Under low memory the existing implementation relies upon waiting for I/O
submitted recursively to generic_make_request() completing before the original
generic_make_request() call can return.

This patch moves the I/O submission to a workqueue so the original
generic_make_request() can return immediately.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:16 -07:00
Milan Broz 93e605c237 [PATCH] dm crypt: restructure write processing
Restructure the dm-crypt write processing in preparation for workqueue changes
in the next patches.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:15 -07:00
Milan Broz 8b00445716 [PATCH] dm crypt: restructure for workqueue change
Restructure part of the dm-crypt code in preparation for workqueue changes.

Use 'base_bio' or 'clone' variable names consistently throughout.  No
functional changes are included in this patch.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:15 -07:00
Milan Broz e48d4bbf96 [PATCH] dm crypt: add key msg
Add the facility to wipe the encryption key from memory (for example while a
laptop is suspended) and reinstate it later (when the laptop gets resumed).

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:15 -07:00
Milan Broz 8757b7764f [PATCH] dm table: add target preresume
This patch adds a target preresume hook.

It is called before the targets are resumed and if it returns an error the
resume gets cancelled.

The crypt target will use this to indicate that it is unable to process I/O
because no encryption key has been supplied.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:15 -07:00
Bryn Reeves cc1092019c [PATCH] dm: add debug macro
Add CONFIG_DM_DEBUG and DMDEBUG() macro.

Signed-off-by: Bryn Reeves <breeves@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:15 -07:00
Hannes Reinecke 8560ed6fa8 [PATCH] dm: add uevent change event on resume
Device-mapper devices are not accessible until a 'resume' ioctl has been
issued.  For userspace to find out when this happens we need to generate an
uevent for udev to take appropriate action.

As discussed at OLS we should send 'change' events for 'resume'.  We can think
of no useful purpose served by also having 'suspend' events.

Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:15 -07:00
Micha³ Miros³aw e69fae561f [PATCH] dm mpath: use kzalloc
Use kzalloc() instead of kmalloc() + memset().

Signed-off-by: Micha³ Miros³aw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:15 -07:00
Micha³ Miros³aw 28f16c2039 [PATCH] dm mpath: tidy ctr
After initialising m->ti, there's no need to pass it in subsequent calls to
static functions used for parsing parameters.

Signed-off-by: Micha³ Miros³aw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:15 -07:00
Jonathan Brassow e52b8f6dbe [PATCH] dm mirror: remove trailing space from table
Remove trailing space from 'dmsetup table' output.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:15 -07:00
Alasdair G Kergon 695368ac33 [PATCH] dm snapshot: fix freeing pending exception
If a snapshot became invalid while there are outstanding pending_exceptions,
when pending_complete() processes each one it forgets to remove the
corresponding exception from its exception table before freeing it.

Fix this by moving the 'out:' label up one statement so that
remove_exception() is always called.  Then __invalidate_exception() no longer
needs to call it and its 'pe' argument become superfluous.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:15 -07:00
Alasdair G Kergon 4b832e8de2 [PATCH] dm snapshot: tidy pe ref counting
Rename sibling_count to ref_count and introduce get and put functions.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:14 -07:00
Alasdair G Kergon ca3a931fd3 [PATCH] dm snapshot: add workqueue
Add a workqueue so that I/O can be queued up to be flushed from a separate
thread (e.g.  if local interrupts are disabled).

A new per-snapshot spinlock pe_lock is introduced to protect queued_bios.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:14 -07:00
Alasdair G Kergon 9d493fa8c9 [PATCH] dm snapshot: tidy pending_complete
This patch rearranges the pending_complete() code so that the functional
changes in subsequent patches are clearer.

By consolidating the error and the non-error paths, we can move
error_snapshot_bios() and __flush_bios() in line.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:14 -07:00
Alasdair G Kergon ba40a2aa6e [PATCH] dm snapshot: tidy snapshot_map
This patch rearranges the snapshot_map code so that the functional changes in
subsequent patches are clearer.

The only functional change is to replace the existing read lock with a write
lock which the next patch needs.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:14 -07:00
Mark McLoughlin 927ffe7c9a [PATCH] dm snapshot: fix metadata writing when suspending
When suspending a device-mapper device, dm_suspend() sleeps until all
necessary I/O is completed.  This state is triggered by a callback from
persistent_commit().  But some I/O can still be issued *after* the callback
(to prepare the next metadata area for use if the current one is full).  This
patch delays the callback until after that I/O is complete.

Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:14 -07:00
Mark McLoughlin e4ff496db7 [PATCH] dm snapshot: make read and write exception functions void
read_exception() and write_exception() only return an error if supplied with
an out-of-range index.  If this ever happens it's the result of a bug in the
calling code so we handle this with an assertion and remove the error handling
in the callers.

Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:14 -07:00
Mark McLoughlin f9cea4f707 [PATCH] dm snapshot: fix metadata error handling
Fix the error handling when store.read_metadata is called: the error should be
returned immediately.

Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:14 -07:00
Mark McLoughlin 4c7e3bf44d [PATCH] dm snapshot: allow zero chunk_size
The chunk size of snapshots cannot be changed so it is redundant to require it
as a parameter when activating an existing snapshot.  Allow a value of zero in
this case and ignore it.  For a new snapshot, use a default value if zero is
specified.

Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:14 -07:00
Milan Broz 92c060a692 [PATCH] dm snapshot: fix invalidation ENOMEM
Fix ENOMEM error sign.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:14 -07:00
Ishai Rabinovitz e3f6ac6123 [PATCH] dm: fix alloc_dev error path
While reading the code I found a bug in the error path in alloc_dev in dm.c

When blk_alloc_queue fails there is no call to free_minor.

This patch fixes the problem.

Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:14 -07:00
Milan Broz e90dae1f58 [PATCH] dm: support ioctls on mapped devices: fix with fake file
The new ioctl code passes the wrong file pointer to the underlying device.
No file pointer is available so make a temporary fake one.

ioctl_by_bdev() does set_fs(KERNEL_DS) so it's for ioctls originating
within the kernel and unsuitable here.  We are processing ioctls that
originated in userspace and mapping them to different devices.  Fixing the
existing callers that pass a NULL file struct and consolidating the
fake_file users are separate matters to solve in later patches.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:13 -07:00
Alasdair G Kergon 7006f6eca8 [PATCH] dm: export blkdev_driver_ioctl
Export blkdev_driver_ioctl for device-mapper.

If we get as far as the device-mapper ioctl handler, we know the ioctl is not
a standard block layer BLK* one, so we don't need to check for them a second
time and can call blkdev_driver_ioctl() directly.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:13 -07:00
Milan Broz 9af4aa30b7 [PATCH] dm mpath: support ioctls
When an ioctl is performed on a multipath device simply pass it on to the
underlying block device through current_path.  If current path is not yet
selected, select it.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:13 -07:00
Milan Broz ab17ffa440 [PATCH] dm linear: support ioctls
When an ioctl is performed on a device with a linear target, simply pass it on
to the underlying block device.

Note that the ioctl will pass through the filtering in blkdev_ioctl() twice.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:13 -07:00
Milan Broz aa129a2247 [PATCH] dm: support ioctls on mapped devices
Extend the core device-mapper infrastructure to accept arbitrary ioctls on a
mapped device provided that it has exactly one target and it is capable of
supporting ioctls.

[We can't use unlocked_ioctl because we need 'inode': 'file' might be NULL.
Is it worth changing this?]

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Arnd Bergmann <arnd@arndb.de> wrote:

> Am Wednesday 21 June 2006 21:31 schrieb Alasdair G Kergon:
> > static struct block_device_operations dm_blk_dops = {
> > .open = dm_blk_open,
> > .release = dm_blk_close,
> > +.ioctl = dm_blk_ioctl,
> > .getgeo = dm_blk_getgeo,
> > .owner = THIS_MODULE
>
> I guess this also needs a ->compat_ioctl method, otherwise it won't
> work for ioctl numbers that have a compat_ioctl implementation in the
> low-level device driver.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:13 -07:00
David Howells 9361401eb7 [PATCH] BLOCK: Make it possible to disable the block layer [try #6]
Make it possible to disable the block layer.  Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.

This patch does the following:

 (*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
     support.

 (*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
     an item that uses the block layer.  This includes:

     (*) Block I/O tracing.

     (*) Disk partition code.

     (*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.

     (*) The SCSI layer.  As far as I can tell, even SCSI chardevs use the
     	 block layer to do scheduling.  Some drivers that use SCSI facilities -
     	 such as USB storage - end up disabled indirectly from this.

     (*) Various block-based device drivers, such as IDE and the old CDROM
     	 drivers.

     (*) MTD blockdev handling and FTL.

     (*) JFFS - which uses set_bdev_super(), something it could avoid doing by
     	 taking a leaf out of JFFS2's book.

 (*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
     linux/elevator.h contingent on CONFIG_BLOCK being set.  sector_div() is,
     however, still used in places, and so is still available.

 (*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
     parts of linux/fs.h.

 (*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.

 (*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.

 (*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
     is not enabled.

 (*) fs/no-block.c is created to hold out-of-line stubs and things that are
     required when CONFIG_BLOCK is not set:

     (*) Default blockdev file operations (to give error ENODEV on opening).

 (*) Makes some /proc changes:

     (*) /proc/devices does not list any blockdevs.

     (*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.

 (*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.

 (*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
     given command other than Q_SYNC or if a special device is specified.

 (*) In init/do_mounts.c, no reference is made to the blockdev routines if
     CONFIG_BLOCK is not defined.  This does not prohibit NFS roots or JFFS2.

 (*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
     error ENOSYS by way of cond_syscall if so).

 (*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
     CONFIG_BLOCK is not set, since they can't then happen.

Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2006-09-30 20:52:31 +02:00
Jens Axboe 4aff5e2333 [PATCH] Split struct request ->flags into two parts
Right now ->flags is a bit of a mess: some are request types, and
others are just modifiers. Clean this up by splitting it into
->cmd_type and ->cmd_flags. This allows introduction of generic
Linux block message types, useful for sending generic Linux commands
to block devices.

Signed-off-by: Jens Axboe <axboe@suse.de>
2006-09-30 20:23:37 +02:00
Rik Snel 3c164bd815 [BLOCK] dm-crypt: trivial comment improvements
Just some minor comment nits.

- little-endian is better than low-endian
- and since it is called essiv everywere it should also be essiv
  in the comments (and not ess_iv)

Signed-off-by: Rik Snel <rsnel@cube.dyndns.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2006-09-21 11:46:27 +10:00
Herbert Xu 3505868791 [CRYPTO] users: Use crypto_hash interface instead of crypto_digest
This patch converts all remaining crypto_digest users to use the new
crypto_hash interface.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2006-09-21 11:46:21 +10:00
Herbert Xu d1806f6a97 [BLOCK] dm-crypt: Use block ciphers where applicable
This patch converts dm-crypt to use the new block cipher type where
applicable.  It also changes simple cipher operations to use the new
encrypt_one/decrypt_one interface.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2006-09-21 11:46:13 +10:00
NeilBrown ddac7c7e3a [PATCH] md: Fix issues with referencing rdev in md/raid1
We need to be careful when referencing mirrors[i].rdev.  It can disappear
under us at various times.

So:
  fix a couple of problem places.
  comment a couple of non-problem places
  move an 'atomic_add' which deferences rdev down a little
    way to some where where it is sure to not be NULL.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-01 11:39:08 -07:00
NeilBrown 6394cca548 [PATCH] md: fix recent breakage of md/raid1 array checking
A recent patch broke the ability to do a user-request check of a raid1.
This patch fixes the breakage and also moves a comment that was dislocated
by the same patch.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-08-27 11:01:31 -07:00
NeilBrown 8469219596 [PATCH] md: avoid backward event updates in md superblock when degraded.
If we
  - shut down a clean array,
  - restart with one (or more) drive(s) missing
  - make some changes
  - pause, so that they array gets marked 'clean',
the event count on the superblock of included drives
will be the same as that of the removed drives.
So adding the removed drive back in will cause it
to be included with no resync.

To avoid this, we only update the eventcount backwards when the array
is not degraded.  In this case there can (should) be no non-connected
drives that we can get confused with, and this is the particular case
where updating-backwards is valuable.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-08-27 11:01:31 -07:00
Daniel Kobras c06aad854f [PATCH] dm: Fix deadlock under high i/o load in raid1 setup.
On an nForce4-equipped machine with two SATA disk in raid1 setup using dmraid,
we experienced frequent deadlock of the system under high i/o load.  'cat
/dev/zero > ~/zero' was the most reliable way to reproduce them: Randomly
after a few GB, 'cp' would be left in 'D' state along with kjournald and
kmirrord.  The functions cp and kjournald were blocked in did vary, but
kmirrord's wchan always pointed to 'mempool_alloc()'.  We've seen this pattern
on 2.6.15 and 2.6.17 kernels.  http://lkml.org/lkml/2005/4/20/142 indicates
that this problem has been around even before.

So much for the facts, here's my interpretation: mempool_alloc() first tries
to atomically allocate the requested memory, or falls back to hand out
preallocated chunks from the mempool.  If both fail, it puts the calling
process (kmirrord in this case) on a private waitqueue until somebody refills
the pool.  Where the only 'somebody' is kmirrord itself, so we have a
deadlock.

I worked around this problem by falling back to a (blocking) kmalloc when
before kmirrord would have ended up on the waitqueue.  This defeats part of
the benefits of using the mempool, but at least keeps the system running.  And
it could be done with a two-line change.  Note that mempool_alloc() clears the
GFP_NOIO flag internally, and only uses it to decide whether to wait or return
an error if immediate allocation fails, so the attached patch doesn't change
behaviour in the non-deadlocking case.  Path is against current git
(2.6.18-rc4), but should apply to earlier versions as well.  I've tested on
2.6.15, where this patch makes the difference between random lockup and a
stable system.

Signed-off-by: Daniel Kobras <kobras@linux.de>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-08-27 11:01:28 -07:00
Michal Miroslaw 485311a23c [PATCH] dm: BUG/OOPS fix
Fix BUG I tripped on while testing failover and multipathing.

BUG shows up on error path in multipath_ctr() when parse_priority_group()
fails after returning at least once without error.  The fix is to
initialize m->ti early - just after alloc()ing it.

BUG: unable to handle kernel NULL pointer dereference at virtual address 00000000
 printing eip:
c027c3d2
*pde = 00000000
Oops: 0000 [#3]
Modules linked in: qla2xxx ext3 jbd mbcache sg ide_cd cdrom floppy
CPU:    0
EIP:    0060:[<c027c3d2>]    Not tainted VLI
EFLAGS: 00010202   (2.6.17.3 #1)
EIP is at dm_put_device+0xf/0x3b
eax: 00000001   ebx: ee4fcac0   ecx: 00000000   edx: ee4fcac0
esi: ee4fc4e0   edi: ee4fc4e0   ebp: 00000000   esp: c5db3e78
ds: 007b   es: 007b   ss: 0068
Process multipathd (pid: 15912, threadinfo=c5db2000 task=ef485a90)
Stack: ec4eda40 c02816bd ee4fc4c0 00000000 f7e89498 f883e0bc c02816f6 f7e89480
       f7e8948c c0281801 ffffffea f7e89480 f883e080 c0281ffe 00000001 00000000
       00000004 dfe9cab8 f7a693c0 f883e080 f883e0c0 ca4b99c0 c027c6ee 01400000
Call Trace:
 <c02816bd> free_pgpaths+0x31/0x45  <c02816f6> free_priority_group+0x25/0x2e
 <c0281801> free_multipath+0x35/0x67  <c0281ffe> multipath_ctr+0x123/0x12d
 <c027c6ee> dm_table_add_target+0x11e/0x18b  <c027e5b4> populate_table+0x8a/0xaf
 <c027e62b> table_load+0x52/0xf9  <c027ec23> ctl_ioctl+0xca/0xfc
 <c027e5d9> table_load+0x0/0xf9  <c0152146> do_ioctl+0x3e/0x43
 <c0152360> vfs_ioctl+0x16c/0x178  <c01523b4> sys_ioctl+0x48/0x60
 <c01029b3> syscall_call+0x7/0xb
Code: 97 f0 00 00 00 89 c1 83 c9 01 80 e2 01 0f 44 c1 88 43 14 8b 04 24 59 5b 5e 5f 5d c3 53 89 c1 89 d3 ff 4a 08 0f 94 c0 84 c0 74 2a <8b> 01 8b 10 89 d8 e8 f6 fb ff ff 8b 03 8b 53 04 89 50 04 89 02
EIP: [<c027c3d2>] dm_put_device+0xf/0x3b SS:ESP 0068:c5db3e78

Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-08-14 12:54:29 -07:00
NeilBrown f9abd1ace4 [PATCH] md: Fix a bug that recently crept into md/linear
A recent patch that allowed linear arrays to be reconfigured on-line
allowed in a bug which results in divide by zero - not all
mddev->array_size were converted to conf->array_size.

This patch finished the conversion and fixed the bug.

The offending patch was commit 7c7546ccf6.

Thanks to Simon Kirby <sim@netnation.com> for the bug report.

Cc: Simon Kirby <sim@netnation.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-08-06 08:57:46 -07:00
Andrew Morton d0a0a5ee7a [PATCH] md: fix oops in error-handling
During early MD setup (superblock reading), we don't have a personality yet.
But the error-handling code tries to dereference mddev->pers.  Fix.

Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:17 -07:00
NeilBrown d695043259 [PATCH] md: include sector number in messages about corrected read errors
This is generally useful, but particularly helps see if it is the same sector
that always needs correcting, or different ones.

[akpm@osdl.org: fix printk warnings]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:17 -07:00
NeilBrown 67463acb64 [PATCH] md: require CAP_SYS_ADMIN for (re-)configuring md devices via sysfs
The ioctl requires CAP_SYS_ADMIN, so sysfs should too.  Note that we don't
require CAP_SYS_ADMIN for reading attributes even though the ioctl does.
There is no reason to limit the read access, and much of the information is
already available via /proc/mdstat

Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:17 -07:00
NeilBrown 80ca3a44f5 [PATCH] md: unify usage of symbolic names for perms
Some places we use number (0660) someplaces names (S_IRUGO).  Change all
numbers to be names, and change 0655 to be what it should be.

Also make some formatting more consistent.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:17 -07:00
NeilBrown 5e3db645f8 [PATCH] md: fix usage of wrong variable in raid1
Though it rarely matters, we should be using 's' rather than r1_bio->sector
here.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:17 -07:00
NeilBrown ae3c20ccf8 [PATCH] md: fix some small races in bitmap plugging in raid5
The comment gives more details, but I didn't quite have the sequencing write,
so there was room for races to leave bits unset in the on-disk bitmap for
short periods of time.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:17 -07:00
NeilBrown 7c785b7a18 [PATCH] md: fix a plug/unplug race in raid5
When a device is unplugged, requests are moved from one or two (depending on
whether a bitmap is in use) queues to the main request queue.

So whenever requests are put on either of those queues, we should make sure
the raid5 array is 'plugged'.  However we don't.  We currently plug the raid5
queue just before putting requests on queues, so there is room for a race.  If
something unplugs the queue at just the wrong time, requests will be left on
the queue and nothing will want to unplug them.  Normally something else will
plug and unplug the queue fairly soon, but there is a risk that nothing will.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:16 -07:00
NeilBrown ff4e8d9a9f [PATCH] md: fix resync speed calculation for restarted resyncs
We introduced 'io_sectors' recently so we could count the sectors that causes
io during resync separate from sectors which didn't cause IO - there can be a
difference if a bitmap is being used to accelerate resync.

However when a speed is reported, we find the number of sectors processed
recently by subtracting an oldish io_sectors count from a current
'curr_resync' count.  This is wrong because curr_resync counts all sectors,
not just io sectors.

So, add a field to mddev to store the curren io_sectors separately from
curr_resync, and use that in the calculations.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:16 -07:00
NeilBrown 0b8c9de05c [PATCH] md: delay starting md threads until array is completely setup
When an array is started we start one or two threads (two if there is a
reshape or recovery that needs to be completed).

We currently start these *before* the array is completely set up and in
particular before queue->queuedata is set.  If the thread actually starts
very quickly on another CPU, we can end up dereferencing queue->queuedata
and oops.

This patch also makes sure we don't try to start a recovery if a reshape is
being restarted.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:16 -07:00
NeilBrown 31b65a0d38 [PATCH] md: set desc_nr correctly for version-1 superblocks
This has to be done in ->load_super, not ->validate_super

Without this, hot-adding devices to an array doesn't always
work right - though there is a work around in mdadm-2.5.2 to
make this less of an issue.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:16 -07:00
NeilBrown f4370781d8 [PATCH] md: possible fix for unplug problem
I have reports of a problem with raid5 which turns out to be because the raid5
device gets stuck in a 'plugged' state.  This shouldn't be able to happen as
3msec after it gets plugged it should get unplugged.  However it happens
none-the-less.  This patch fixes the problem and is a reasonable thing to do,
though it might hurt performance slightly in some cases.

Until I can find the real problem, we should probably have this workaround in
place.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:16 -07:00
Ingo Molnar 663d440eaa [PATCH] lockdep: annotate blkdev nesting
Teach special (recursive) locking code to the lock validator.

Effects on non-lockdep kernels:

- the introduction of the following function variants:

  extern struct block_device *open_partition_by_devnum(dev_t, unsigned);

  extern int blkdev_put_partition(struct block_device *);

  static int
  blkdev_get_whole(struct block_device *bdev, mode_t mode, unsigned flags);

 which on non-lockdep are the same as open_by_devnum(), blkdev_put()
 and blkdev_get().

- a subclass parameter to do_open(). [unused on non-lockdep]

- a subclass parameter to __blkdev_put(), which is a new internal
  function for the main blkdev_put*() functions. [parameter unused
  on non-lockdep kernels, except for two sanity check WARN_ON()s]

these functions carry no semantical difference - they only express
object dependencies towards the lockdep subsystem.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-03 15:27:10 -07:00
Jörn Engel 6ab3d5624e Remove obsolete #include <linux/config.h>
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-30 19:25:36 +02:00
Linus Torvalds 602cada851 Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
  [PATCH] devfs: Remove it from the feature_removal.txt file
  [PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
  [PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
  [PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
  [PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
  [PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
  [PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
  [PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
  [PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
  [PATCH] devfs: Remove devfs_remove() function from the kernel tree
  [PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
  [PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
  [PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
  [PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
  [PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
  [PATCH] devfs: Remove devfs support from the sound subsystem
  [PATCH] devfs: Remove devfs support from the ide subsystem.
  [PATCH] devfs: Remove devfs support from the serial subsystem
  [PATCH] devfs: Remove devfs from the init code
  [PATCH] devfs: Remove devfs from the partition code
  ...
2006-06-29 14:19:21 -07:00
Adrian Bunk cfb9e32f2f [PATCH] drivers/md/raid5.c: remove an unused variable
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-29 10:26:21 -07:00
Greg Kroah-Hartman 890fbae281 [PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
Just removes a few unused #defines and fixes some comments due to
devfs now being gone.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-26 12:25:09 -07:00
Greg Kroah-Hartman ce7b0f46bb [PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
And remove the now unneeded number field.
Also fixes all drivers that set these fields.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-26 12:25:08 -07:00
Greg Kroah-Hartman 96192ff1a9 [PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
Also fixes all drivers that set this field.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-26 12:25:08 -07:00
Greg Kroah-Hartman ff23eca3e8 [PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
Also fixes up all files that #include it.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-26 12:25:08 -07:00
Greg Kroah-Hartman 8ab5e4c15b [PATCH] devfs: Remove devfs_remove() function from the kernel tree
Removes the devfs_remove() function and all callers of it.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-26 12:25:07 -07:00
Greg Kroah-Hartman 1a715c5cf9 [PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
Removes the devfs_mk_bdev() function and all callers of it.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-26 12:25:06 -07:00
Greg Kroah-Hartman 95dc112a57 [PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
Removes the devfs_mk_dir() function and all callers of it.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-26 12:25:06 -07:00
Adrian Bunk 0538195424 [PATCH] drivers/md/md.c: make code static
Make needlessly global code static.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:40 -07:00
NeilBrown f655675b3f [PATCH] md: Allow the write_mostly flag to be set via sysfs
It appears in /sys/mdX/md/dev-YYY/state
and can be set or cleared by writing 'writemostly' or '-writemostly'
respectively.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:40 -07:00
NeilBrown a94213b1fa [PATCH] md: Allow resync_start to be set and queried via sysfs
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:40 -07:00
NeilBrown d4dbd0250e [PATCH] md: Allow raid 'layout' to be read and set via sysfs
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown 45dc2de1e5 [PATCH] md: Allow rdev state to be set via sysfs
The md/dev-XXX/state file can now be written:

 "faulty" simulates an error on the device
 "remove" removes the device from the array (if it is not busy)

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown 9e653b6342 [PATCH] md: Set/get state of array via sysfs
This allows the state of an md/array to be directly controlled via sysfs and
adds the ability to stop and array without tearing it down.

Array states/settings:

 clear
     No devices, no size, no level
     Equivalent to STOP_ARRAY ioctl
 inactive
     May have some settings, but array is not active
        all IO results in error
     When written, doesn't tear down array, but just stops it
 suspended (not supported yet)
     All IO requests will block. The array can be reconfigured.
     Writing this, if accepted, will block until array is quiescent
 readonly
     no resync can happen.  no superblocks get written.
     write requests fail
 read-auto
     like readonly, but behaves like 'clean' on a write request.

 clean - no pending writes, but otherwise active.
     When written to inactive array, starts without resync
     If a write request arrives then
       if metadata is known, mark 'dirty' and switch to 'active'.
       if not known, block and switch to write-pending
     If written to an active array that has pending writes, then fails.
 active
     fully active: IO and resync can be happening.
     When written to inactive array, starts with resync

 write-pending (not supported yet)
     clean, but writes are blocked waiting for 'active' to be written.

 active-idle
     like active, but no writes have been seen for a while (100msec).

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown 4254376914 [PATCH] md: Don't write dirty/clean update to spares - leave them alone
- record the 'event' count on each individual device (they
  might sometimes be slightly different now)
- add a new value for 'sb_dirty': '3' means that the super
  block only needs to be updated to record a clean<->dirty
  transition.
- Prefer odd event numbers for dirty states and even numbers
  for clean states
- Using all the above, don't update the superblock on
  a spare device if the update is just doing a clean-dirty
  transition.  To accomodate this, a transition from
  dirty back to clean might now decrement the events counter
  if nothing else has changed.

The net effect of this is that spare drives will not see any IO requests
during normal running of the array, so they can go to sleep if that is what
they want to do.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown 07d84d109d [PATCH] md: Allow re-add to work on array without bitmaps
When an array has a bitmap, a device can be removed and re-added and only
blocks changes since the removal (as recorded in the bitmap) will be resynced.

It should be possible to do a similar thing to arrays without bitmaps.  i.e.
if a device is removed and re-added and *no* changes have been made in the
interim, then the add should not require a resync.

This patch allows that option.  This means that when assembling an array one
device at a time (e.g.  during device discovery) the array can be enabled
read-only as soon as enough devices are available, but extra devices can still
be added without causing a resync.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown 3285edf152 [PATCH] md: Fix bug that stops raid5 resync from happening
As data_disks is *less* than raid_disks, the current test here is obviously
wrong.  And as the difference is already available in conf->max_degraded, it
makes much more sense to use that.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
akpm@osdl.org b3cc9ec76b [PATCH] md: Fix Kconfig error
RAID5 recently changed to RAID456

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
Justin Piszcz 4d2554d045 [PATCH] md: md Kconfig speeling feex
I was experimenting with Linux SW raid today and found a spelling error when
reading the help menus...  (and fly spell found more).

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown 8838832830 [PATCH] md: Calculate correct array size for raid10 in new offset mode
The size calculation made assumtion which the new offset mode didn't
follow.  This gets the size right in all cases.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown ce25c31bdd [PATCH] md: Change md/bitmap file handling to use bmap to file blocks-fix
Fix problems with new bmap based access to bitmap files.

1/ When not using a file based bitmap, attach a NULL list of buffers
   to each page so the common free_buffer routine can cope.
2/ Use submit_bh to read as well as write, rather than vfs_read.
   This makes read and write more symetric.
3/ sync the file before reading, to ensure that the page cache has no
   dirty pages that might get written out later.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:38 -07:00
NeilBrown d785a06a0b [PATCH] md/bitmap: change md/bitmap file handling to use bmap to file blocks
If md is asked to store a bitmap in a file, it tries to hold onto the page
cache pages for that file, manipulate them directly, and call a cocktail of
operations to write the file out.  I don't believe this is a supportable
approach.

This patch changes the approach to use the same approach as swap files.  i.e.
bmap is used to enumerate all the block address of parts of the file and we
write directly to those blocks of the device.

swapfile only uses parts of the file that provide a full pages at contiguous
addresses.  We don't have that luxury so we have to cope with pages that are
non-contiguous in storage.  To handle this we attach buffers to each page, and
store the addresses in those buffers.

With this approach the pagecache may contain data which is inconsistent with
what is on disk.  To alleviate the problems this can cause, md invalidates the
pagecache when releasing the file.  If the file is to be examined while the
array is active (a non-critical but occasionally useful function), O_DIRECT io
must be used.  And new version of mdadm will have support for this.

This approach simplifies a lot of code:
 - we no longer need to keep a list of pages which we need to wait for,
   as the b_endio function can keep track of how many outstanding
   writes there are.  This saves a mempool.
 - -EAGAIN returns from write_page are no longer possible (not sure if
    they ever were actually).

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:38 -07:00