Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_sourcesink we only need to store in ep->driver_data pointer
to struct f_sourcesink, as it's used in source_sink_complete() callback.
All other uses of ep->driver_data are now meaningless and can be safely
removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_serial, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_rndis, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_printer we only need to store in ep->driver_data pointer to
struct printer_dev, as it's used in rx_complete() and tx_complete()
callbacks. All other uses of ep->driver_data are now meaningless and can
be safely removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_phonet we only need to store in ep->driver_data pointer to
struct f_phonet, as it's used in pn_tx_complete() and pn_rx_complete()
callbacks. All other uses of ep->driver_data are now meaningless and can
be safely removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_obex, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_ncm, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_midi we only need to store in ep->driver_data pointer to
struct f_midi, as it's used in f_midi_complete() callback and related
functions. All other uses of ep->driver_data are now meaningless and
can be safely removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_mass_storage we only need to store in ep->driver_data
pointer to struct fsg_common, which is used in bulk_in_complete() and
bulk_out_complete() callbacks. All other uses of ep->driver_data are now
meaningless and can be safely removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_hid we only need to store in ep->driver_data pointer to
struct f_loopback, as it's used in loopback_complete() callback. All
other uses of ep->driver_data are now meaningless and can be safely
removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_hid we only need to store in ep->driver_data pointer to
struct f_hidg, as it's used in f_hidg_req_complete() callback. All
other uses of ep->driver_data are now meaningless and can be safely
removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_ecm, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_acm we only need to store in ep->driver_data pointer to
struct f_acm, as it's used in acm_complete_set_line_coding() callback.
All other uses of ep->driver_data are now meaningless and can be safely
removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_ecm, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces usb_ep_autoconfig_release() function which allows
to release endpoint previously obtained from usb_ep_autoconfig() during
USB function bind.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The 'driver_data' field in ep0 is never set to pointer to cdev, so we
have to obtain it from another source as in this context ep->driver_data
contains invalid data.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix comments in code to make them up to date.
composite: claiming endpoint is now done by setting ep->claimed flag,
not ep->driver_data.
epautoconf: usb_ep_autoconfig() and usb_ep_autoconfig_ss() return
claimed endpoint with ep->claimed flag already set.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The millisecond of the last second will be normal if tv_sec is
overflowed. But for y2038 consistency and demonstration purpose,
and avoiding further risks, we need to remove 'timeval' in this
driver, to avoid similair problems.
Signed-off-by: Pingbo Wen <pingbo.wen@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the host and gadget can't agree with transfer length before
each transfer, but they agree with max packet size for each
endpoint, we use max packet size to format data pattern.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB network adapters support Jumbo frames. The only thing blocking
that feature is the code in the gadget driver that disposes of
packets larger than 1518 bytes, and the limit on the ioctl to set
the mtu.
This patch relaxes these limits, and allows up to 15k frames sizes.
The 15k value was chosen because 16k does not work on all platforms,
and usingclose to 16k will result in allocating 5 or 8 4k pages to
store the skb, wasting pages at no measurable performance gain.
On a topic-miami board (Zynq-7000), iperf3 performance reports:
MTU= 1500, PC-to-gadget: 139 Mbps, Gadget-to-PC: 116 Mbps
MTU=15000, PC-to-gadget: 239 Mbps, Gadget-to-PC: 361 Mbps
On boards with slower CPUs the performance improvement will be
relatively much larger, e.g. an OMAP-L138 increased from 40 to
220 Mbps using a similar patch on an 2.6.37 kernel.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Felipe Balbi <balbi@ti.com>
struct at91_udc_data is now only used inside the driver, move it to its
include.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
f_midi is not checking whether there is an error on usb_ep_queue
request, ignoring potential problems, such as memory leaks.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of allowing a range of 2 to 4 requests,
let's allow the user choose up to 32 requests
as that will give us a better chance of keeping
controller busy.
We still maintain default of 2 so users shouldn't
be affected.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dummy_timer uses transfer() to update transfer limit. However,
limit passed to dummy_timer changes depending on transfer type,
so the actual limit is overwritten.
This can cause unpredictably slow / fast bulk transfers when
coupled with control / interrupt transfers.
Fix by returning actual amount of data sent in transfer() and
substracting from total.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
transfer() schedules a rescan for transfers larger than
maxpacket, which is wrong for transfers that are multiples
of maxpacket.
Rewrite to fix and clarify packet multiple / remainder
transfer logic.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We already know at this point that to_host is false.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
currently, when a zlp flag is set and an urb/usb_request
buffer is filled without a short packet, transfer() leaves
its status at -EINPROGRESS and does not rescan for short
packet.
In a scenario where ep.maxpacket bytes are copied,
URB_ZERO_PACKET is set, urb buffer is filled and usb_request
buffer is not, transfer() returns with an urb with
-EINPROGRESS status, which dummy_hcd treats as incomplete
transfer.
Check for zlp and rescan appropriately.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The recently added endpoint capabilities flags verification breaks Atmel
USBA because the endpoint configuration was only added when the driver
is bound using the legacy pdata interface.
Convert endpoint configuration to new capabilities model when driver is
bound to a device tree as well.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Fixes: 47bef38651 ("usb: gadget: atmel_usba_udc: add ep capabilities support")
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If a failure happens early in udc_pci_probe(), error handling code
just kfree(dev) and returns. The patch adds proper resource
deallocations in udc_pci_probe() itself,
since udc_pci_remove() is not suitabe to be called so early
in initialization process.
By the way, iounmap(dev->regs) is replaced by iounmap(dev->virt_addr)
in udc_pci_remove() for clarity.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes possible regression introduced by
patch reworking endpoint claiming mechanism. It restores
setring ep->driver_data to NULL in usb_ep_autoconfig_reset(),
which was removed by patch commit cc476b42a3.
Fixes: cc476b42a3 ("usb: gadget: encapsulate endpoint
claiming mechanism")
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Definitions from linux/platform_data/atmel.h are not used, remove the
include.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New support for Allwinne SoC on the MUSB driver has been added to the list of
glue layers. MUSB also got support for building all DMA engines in one binary;
this will be great for distros.
DWC3 now has no trace of dev_dbg()/dev_vdbg() usage. We will rely solely on
tracing to debug DWC3. There was also a fix for memory corruption with EP0 when
maxpacket size transfers are > 512 bytes.
Robert's EP capabilities flags is making EP selection a lot simpler. UDCs are
now required to set these flags up when adding endpoints to the framework.
Other than these, we have the usual set of miscelaneous cleanups and minor
fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WuIB
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.3 merge window
New support for Allwinne SoC on the MUSB driver has been added to the list of
glue layers. MUSB also got support for building all DMA engines in one binary;
this will be great for distros.
DWC3 now has no trace of dev_dbg()/dev_vdbg() usage. We will rely solely on
tracing to debug DWC3. There was also a fix for memory corruption with EP0 when
maxpacket size transfers are > 512 bytes.
Robert's EP capabilities flags is making EP selection a lot simpler. UDCs are
now required to set these flags up when adding endpoints to the framework.
Other than these, we have the usual set of miscelaneous cleanups and minor
fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Looks like the word "contiguous" is often mistyped.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
<linux/uaccess.h> was originally being pulled
indirectly through some other header, however
it's not anymore, so we need to include it
directly
Reported-by: Jim Davis <jim.epost@gmail.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This header file contains helpers for quirks based on UDC controller name.
Since we have generic quirk bitfields in usb_gadget structure for all of
these quirks we don't need to have this header any longer.
This patch removes gadget_chips.h file and makes sure that it's no longer
included anywhere in kernel sources.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add 'match_ep' callback to utilize chip-specific knowledge in endpoint matching
process. Function does the same that was done by chip-specific code inside
of epautoconf. Now this code can be removed from there to separate generic code
from platform specific logic.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add 'match_ep' callback to utilize chip-specific knowledge in endpoint matching
process. Function does the same that was done by chip-specific code inside
of epautoconf. Now this code can be removed from there to separate generic code
from platform specific logic.
[ balbi@ti.com : fix build breakage ]
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add 'match_ep' callback to utilize chip-specific knowledge in endpoint matching
process. Function does the same that was done by chip-specific code inside
of epautoconf. Now this code can be removed from there to separate generic code
from platform specific logic.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move find_ep() to udc-core and rename it to gadget_find_ep_by_name().
It can be used in UDC drivers, especially in 'match_ep' callback after
moving chip-specific endpoint matching logic from epautoconf to UDC
drivers.
Replace all calls of find_ep() function with gadget_find_ep_by_name().
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move ep_matches() function to udc-core and rename it to
usb_gadget_ep_match_desc(). This function can be used by UDC drivers
in 'match_ep' callback to avoid writing lots of repetitive code.
Replace all calls of ep_matches() with usb_gadget_ep_match_desc().
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add callback that is called by epautoconf to allow UDC driver match the
best endpoint for specific descriptor. It's intended to supply mechanism
which allows to get rid of chip-specific endpoint matching code from
epautoconf.
If gadget has set 'ep_match' callback we prefer to call it first, and
if it fails to find matching endpoint, then we try to use default matching
algorithm.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Rework ep_matches() function to make it shorter and more readable.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As function ep_matches() is used to match endpoint with usb descriptor it's
highly unintuitive that it modifies endpoint and descriptor structures fields.
This patch moves code configuring ep and desc from ep_matches() to
usb_ep_autoconfig_ss(), so now function ep_matches() does nothing more than
its name suggests.
[ balbi@ti.com : fix build warning ]
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The same effect can be achieved by using capabilities flags, so now we can
get rid of handling of hardware specific limitations in generic code.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Introduce endpoint matching mechanism basing on endpoint capabilities
flags. We check if endpoint supports transfer type and direction requested
in ep descriptor. Since we have this new endpoint matching mechanism
there is no need to have old code guessing endpoint capabilities basing
on its name, so we are getting rid of it. Remove also the obsolete comment.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So far it was necessary for usb functions to set ep->driver_data in
endpoint obtained from autoconfig to non-null value, to indicate that
endpoint is claimed by function (in autoconfig it was checked if endpoint
has set this field to non-null value, and if it has, it was assumed that
it is claimed). It could cause bugs because if some function doesn't
set this field autoconfig could return the same endpoint more than one
time.
To help to avoid such bugs this patch adds claimed flag to struct usb_ep,
and encapsulates endpoint claiming mechanism inside usb_ep_autoconfig_ss()
and usb_ep_autoconfig_reset(), so now usb functions don't need to perform
any additional actions to mark endpoint obtained from autoconfig as claimed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 913e4a90b6 ("usb: gadget: f_uac2:
finalize wMaxPacketSize according to bandwidth")
added a possible build warning when calling
min(). In order to fix the warning, we just
make sure to call min_t() and tell that its
arguments should be u16.
Cc: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes a bug in the error pathway of
usb_add_gadget_udc_release() in udc-core.c. If the udc registration
fails, the gadget registration is not fully undone; there's a
put_device(&gadget->dev) call but no device_del().
CC: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function printer_func_disable() has called spinlock on printer_dev->lock,
and it'll call function chain of
printer_reset_interface()
|
+---dwc3_gadget_ep_disable()
|
+---__dwc3_gadget_ep_disable()
|
+---dwc3_remove_requests()
|
+---dwc3_gadget_giveback()
|
+---rx_complete()
in the protected block.
However, rx_complete() in f_printer.c calls spinlock on printer_dev->lock
again, which will cause system hang.
The following steps can reproduce this hang:
1. Build the test program from Documentation/usb/gadget_printer.txt as
g_printer
2. Plug in the USB device to a host(such as Ubuntu).
3. on the USB device system run:
#modprobe g_printer.ko
#./g_printer -read_data
4. Unplug the USB device from the host
The system will hang later.
In order to avoid this deadlock, moving the spinlock from
printer_func_disable() into printer_reset_interface() and excluding the block
of calling dwc3_gadget_ep_disable(), in which the critical resource will be
protected by its spinlock in rx_complete().
This commit will fix the system hang with the following calltrace:
INFO: rcu_preempt detected stalls on CPUs/tasks: { 3} (detected by 0, t=21006 jiffies, g=524, c=523, q=2)
sending NMI to all CPUs:
NMI backtrace for cpu 3
CPU: 3 PID: 718 Comm: irq/22-dwc3 Not tainted 3.10.38-ltsi-WR6.0.0.11_standard #2
Hardware name: Intel Corp. VALLEYVIEW B3 PLATFORM/NOTEBOOK, BIOS BYTICRB1.86C.0092.R32.1410021707 10/02/2014
task: f44f4c20 ti: f40f6000 task.ti: f40f6000
EIP: 0060:[<c1824955>] EFLAGS: 00000097 CPU: 3
EIP is at _raw_spin_lock_irqsave+0x35/0x40
EAX: 00000076 EBX: f80fad00 ECX: 00000076 EDX: 00000075
ESI: 00000096 EDI: ffffff94 EBP: f40f7e20 ESP: f40f7e18
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 8005003b CR2: b77ac000 CR3: 01c30000 CR4: 001007f0
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
Stack:
f474a720 f80fad00 f40f7e3c f80f93cc c135d486 00000000 f474a720 f468fb00
f4bea894 f40f7e54 f7e35f19 ffffff00 f468fb00 f468fb24 00000086 f40f7e64
f7e36577 f468fb00 f4bea810 f40f7e74 f7e365a8 f468fb00 f4bea894 f40f7e9c
Call Trace:
[<f80f93cc>] rx_complete+0x1c/0xb0 [g_printer]
[<c135d486>] ? vsnprintf+0x166/0x390
[<f7e35f19>] dwc3_gadget_giveback+0xc9/0xf0 [dwc3]
[<f7e36577>] dwc3_remove_requests+0x57/0x70 [dwc3]
[<f7e365a8>] __dwc3_gadget_ep_disable+0x18/0x60 [dwc3]
[<f7e366e9>] dwc3_gadget_ep_disable+0x89/0xf0 [dwc3]
[<f80f9031>] printer_reset_interface+0x31/0x50 [g_printer]
[<f80f9270>] printer_func_disable+0x20/0x30 [g_printer]
[<f80e6d8b>] composite_disconnect+0x4b/0x90 [libcomposite]
[<f7e39a8b>] dwc3_disconnect_gadget+0x38/0x43 [dwc3]
[<f7e39ad4>] dwc3_gadget_disconnect_interrupt+0x3e/0x5a [dwc3]
[<f7e373b8>] dwc3_thread_interrupt+0x5c8/0x610 [dwc3]
[<c10ac518>] irq_thread_fn+0x18/0x30
[<c10ac800>] irq_thread+0x100/0x130
[<c10ac500>] ? irq_finalize_oneshot.part.29+0xb0/0xb0
[<c10ac650>] ? wake_threads_waitq+0x40/0x40
[<c10ac700>] ? irq_thread_dtor+0xb0/0xb0
[<c1057224>] kthread+0x94/0xa0
[<c182b337>] ret_from_kernel_thread+0x1b/0x28
[<c1057190>] ? kthread_create_on_node+0xc0/0xc0
Signed-off-by: Fupan Li <fupan.li@windriver.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch replace dynamicly allocated luns array with static one.
This simplifies the code of mass storage function and modules.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Add missing return value check. In case of error print debug message
and return error code.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function midi registers two interfaces with single set_alt() function
which means that f_midi_set_alt() is called twice when configuration
is set. That means that endpoint initialization and ep request allocation
is done two times. To avoid this problem we do such things only once,
for interface number 1 (MIDI Streaming interface).
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function ffs_do_functionfs_bind() calls functionfs_bind() which allocates
usb request and increments refcounts. These things needs to be cleaned
up by if further steps of initialization fail by calling functionfs_unbind().
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to USB Audio Device 2.0 Spec, Ch4.10.1.1:
wMaxPacketSize is defined as follows:
Maximum packet size this endpoint is capable of sending or receiving
when this configuration is selected.
This is determined by the audio bandwidth constraints of the endpoint.
In current code, the wMaxPacketSize is defined as the maximum packet size
for ISO endpoint, and it will let the host reserve much more space than
it really needs, so that we can't let more endpoints work together at
one frame.
We find this issue when we try to let 4 f_uac2 gadgets work together [1]
at FS connection.
[1]http://www.spinics.net/lists/linux-usb/msg123478.html
Acked-by: Daniel Mack <zonque@gmail.com>
Cc: andrzej.p@samsung.com
Cc: Daniel Mack <zonque@gmail.com>
Cc: tiwai@suse.de
Cc: <stable@vger.kernel.org> #v3.18+
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After the worker thread is launched, bind function is doing further
configuration. In case of failure stop the thread.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sanjay Singh Rawat <snjsrwt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is an "&&" vs "||" typo here so this loops 3000 times or if we get
unlucky it could loop forever.
Fixes: ceaa0a6eea ('usb: gadget: m66592-udc: add support for TEST_MODE')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We handle the "if (!req->req.length)" condition at the start of the
function and return. We can delete this dead code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace calls of gadget_supports_altsettings() function (which check altset
support by comparing UDC controller name with hardcoded names) with
gadget_is_altset_supported() which checks generic quirk bitfield.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use generic mechanism to check if UDC controller supports zlp.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use generic mechanism to check if UDC controller supports stalling.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to some UDC controllers may not support stalling, usb gadget layer
needs to provide a generic way to inform gadget functions about non-standard
hardware limitations.
This patch adds 'quirk_stall_not_supp' field to struct usb_gadget and helper
function gadget_is_stall_supported(). It also sets 'quirk_stall_not_supp'
to 1 in at91_udc driver, which has such limitation.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to some UDC controllers may not support altsettings, usb gadget layer
needs to provide a generic way to inform gadget functions about non-standard
hardware limitations.
This patch adds 'quirk_altset_not_supp' field to struct usb_gadget and helper
function gadget_is_altset_supported(). It also sets 'quirk_altset_not_supp'
to 1 in pxa25x_udc and pxa27x_udc drivers, which have such limitation.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations, free it while
ether unbind. If otg capability is not defined, keep its otg
descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations, free it while
composite unbind. If otg capability is not defined, keep its otg
descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate usb otg descriptor and initialize it according to gadget's otg
capabilities, if usb_otg_caps is not set, keep settings as current gadget
drivers. With this 2 new interfaces, gadget can use usb_otg_descriptor
for OTG 1.x, and usb_otg20_descriptor for OTG 2.0 or above, and otg
features can be decided by the combination of usb hardware property
and driver config.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Copy usb_otg_descriptor from config's descriptor if host requests
USB_DT_OTG.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use bind_deactivated flag instead of calling usb_function_deactivate()
in function bind(). Field 'can_activate' in struct f_obex is no longer
needed as setting 'bind_deactivated' flag makes us sure, that the function
will be binded only if deactivation can be performed successfully.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use bind_deactivated flag instead of calling usb_function_deactivate()
in function bind().
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces 'bind_deactivated' flag in struct usb_function.
Functions which don't want to be activated automatically after bind should
set this flag, and when they start to be ready to work they should call
usb_function_activate().
When USB function sets 'bind_deactivated' flag, initial deactivation
counter is incremented automatically, so there is no need to call
usb_function_deactivate() in function bind.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using usb_gadget_disconnect to make gadget temporarily invisible to host
doesn't provide desired result, because gadget is connected immediately
after binding regardless to previous usb_gadget_disconnect() calls.
For this reason we use usb_gadget_deactivate() instead of
usb_gadget_disconnect() to make it working as expected.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mass storage spec allows up to 16 LUNs, so let's not
add some more restrictive limits.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
EXPORT_SYMBOL_GPL() is usually placed after function definition
not before.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Creation of LUN 0 may fail (for example due to ENOMEM).
As fsg_common_set_num_buffers() does some memory allocation
we should free it before it becomes unavailable.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Currently this parameter is made optional with the help of a cpp trick.
To allow dropping this hack convert callers to explictly pass a value
for flags.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In big endian cases, the macro cpu_to_le{16,32} unfolds to __swab{16,32}
which provides special case for constants. In little endian cases,
__constant_cpu_to_le{16,32} and cpu_to_le{16,32} expand directly to
the same expression. So, replace __constant_cpu_to_le{16,32} with
cpu_to_le{16,32} with the goal of getting rid of the definition of
__constant_cpu_to_le{16,32} completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
(
- __constant_cpu_to_le16(x)
+ cpu_to_le16(x)
|
- __constant_cpu_to_le32(x)
+ cpu_to_le32(x)
)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
I18N should be spelled as i18n because it's not
an acronym
Signed-off-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In big endian cases, macro cpu_to_le16 unfolds to __swab16 which
provides special case for constants. In little endian cases,
__constant_cpu_to_le16 and cpu_to_le16 expand directly to the
same expression. So, replace __constant_cpu_to_le16 with
cpu_to_le16 with the goal of getting rid of the definition of
__constant_cpu_to_le16 completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_cpu_to_le16(x)
+ cpu_to_le16(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As SourceSink function has been reworked for ConfigFS
composite gadget this comment is no longer valid.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As loopback function has been reworked for ConfigFS
composite gadget this comment is no longer valid.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds removable mass storage support to g_nokia gadget (for N900).
It means that at runtime block device can be exported or unexported.
So it does not export anything by default and thus allows to use MyDocs
partition as before...
[ balbi@ti.com: make it build ]
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a predefined maximum number of printer instances, currently 4.
A chrdev region is allocated accordingly, but with configfs the user
can create as many printer function directories as they like. To make the
number of printer instances consistent with the number of allocated
minors, the limit is enforced at directory creation time.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a predefined maximum number of hid instances, currently 4.
A chrdev region is allocated accordingly, but with configfs the user
can create as many hid function directories as they like. To make
the number of hid instances consistent with the number of allocated minors,
the limit is enforced at directory creation time.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The p_interval should be less if the 'bInterval' at the descriptor
is larger, eg, if 'bInterval' is 5 for HS, the p_interval should be
8000 / 16 = 500.
It fixes the patch 9bb87f1689 ("usb: gadget: f_uac2: send
reasonably sized packets")
Cc: <stable@vger.kernel.org> # v3.18+
Fixes: 9bb87f1689 ("usb: gadget: f_uac2: send reasonably sized packets")
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ep_dequeue() in bdc_ep.c was capturing the hw dequeue pointer
incorrectly by reading the wrong register for the upper 32 bits.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dma_map_single and dma_unmap_single should set "gadget->dev.parent"
instead of "&gadget->dev" in the first argument because the parent has
a udc controller's device pointer.
Otherwise, iommu functions are not called in ARM environment.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was an omission in transition to devm_xxx resource handling.
iounmap(udc->phy_regs) were removed, but ioremap() was left
without devm_.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 3517c31a8e ("usb: gadget: mv_udc: use devm_xxx for probe")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some modules call config_item_init_type_name() and config_group_init_type_name()
with parameter "name" directly controlled by userspace. These two
functions call config_item_set_name() with this name used as a format
string, which can be used to leak information such as content of the
stack to userspace.
For example, make_netconsole_target() in netconsole module calls
config_item_init_type_name() with the name of a newly-created directory.
This means that the following commands give some unexpected output, with
configfs mounted in /sys/kernel/config/ and on a system with a
configured eth0 ethernet interface:
# modprobe netconsole
# mkdir /sys/kernel/config/netconsole/target_%lx
# echo eth0 > /sys/kernel/config/netconsole/target_%lx/dev_name
# echo 1 > /sys/kernel/config/netconsole/target_%lx/enabled
# echo eth0 > /sys/kernel/config/netconsole/target_%lx/dev_name
# dmesg |tail -n1
[ 142.697668] netconsole: target (target_ffffffffc0ae8080) is
enabled, disable to update parameters
The directory name is correct but %lx has been interpreted in the
internal item name, displayed here in the error message used by
store_dev_name() in drivers/net/netconsole.c.
To fix this, update every caller of config_item_set_name to use "%s"
when operating on untrusted input.
This issue was found using -Wformat-security gcc flag, once a __printf
attribute has been added to config_item_set_name().
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case kstrdup() fails the resources to release are
midi->in_port[] and midi. No cards have been registered,
so no need to unregister any.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
My static checker detected the mistake. I fix this by changing "goto
err_irq" to "goto err_req". The label err_irq is not used now
so this patch also removes it.
Signed-off-by: Takeshi Yoshimura <yos@sslab.ics.keio.ac.jp>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit f563d23090 ("usb: gadget: composite: add req_match method
to usb_function") accesses cdev->config even before set config
is invoked causing a NULL pointer dereferencing error while running
Lecroy Mass Storage Compliance test.
Fix it here by accessing cdev->config only if it is non NULL.
Fixes: commit f563d23090 ("usb: gadget: composite: add req_match
method to usb_function").
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
do not try to set cancel function in synchronous operations in
ffs_epfile_{read,write}_iter.
Cc: <stable@vger.kernel.org> # v4.0+
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mass storage function created via configfs always reports eight LUNs
to the hosts even if only one LUN has been configured. Adjust the
number when the USB function is allocated based on LUNs that user
has created.
Cc: <stable@vger.kernel.org>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull more vfs updates from Al Viro:
"Assorted VFS fixes and related cleanups (IMO the most interesting in
that part are f_path-related things and Eric's descriptor-related
stuff). UFS regression fixes (it got broken last cycle). 9P fixes.
fs-cache series, DAX patches, Jan's file_remove_suid() work"
[ I'd say this is much more than "fixes and related cleanups". The
file_table locking rule change by Eric Dumazet is a rather big and
fundamental update even if the patch isn't huge. - Linus ]
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (49 commits)
9p: cope with bogus responses from server in p9_client_{read,write}
p9_client_write(): avoid double p9_free_req()
9p: forgetting to cancel request on interrupted zero-copy RPC
dax: bdev_direct_access() may sleep
block: Add support for DAX reads/writes to block devices
dax: Use copy_from_iter_nocache
dax: Add block size note to documentation
fs/file.c: __fget() and dup2() atomicity rules
fs/file.c: don't acquire files->file_lock in fd_install()
fs:super:get_anon_bdev: fix race condition could cause dev exceed its upper limitation
vfs: avoid creation of inode number 0 in get_next_ino
namei: make set_root_rcu() return void
make simple_positive() public
ufs: use dir_pages instead of ufs_dir_pages()
pagemap.h: move dir_pages() over there
remove the pointless include of lglock.h
fs: cleanup slight list_entry abuse
xfs: Correctly lock inode when removing suid and file capabilities
fs: Call security_ops->inode_killpriv on truncate
fs: Provide function telling whether file_remove_privs() will do anything
...
Pull SCSI target updates from Nicholas Bellinger:
"It's been a busy development cycle for target-core in a number of
different areas.
The fabric API usage for se_node_acl allocation is now within
target-core code, dropping the external API callers for all fabric
drivers tree-wide.
There is a new conversion to RCU hlists for se_node_acl and
se_portal_group LUN mappings, that turns fast-past LUN lookup into a
completely lockless code-path. It also removes the original
hard-coded limitation of 256 LUNs per fabric endpoint.
The configfs attributes for backends can now be shared between core
and driver code, allowing existing drivers to use common code while
still allowing flexibility for new backend provided attributes.
The highlights include:
- Merge sbc_verify_dif_* into common code (sagi)
- Remove iscsi-target support for obsolete IFMarker/OFMarker
(Christophe Vu-Brugier)
- Add bidi support in target/user backend (ilias + vangelis + agover)
- Move se_node_acl allocation into target-core code (hch)
- Add crc_t10dif_update common helper (akinobu + mkp)
- Handle target-core odd SGL mapping for data transfer memory
(akinobu)
- Move transport ID handling into target-core (hch)
- Move task tag into struct se_cmd + support 64-bit tags (bart)
- Convert se_node_acl->device_list[] to RCU hlist (nab + hch +
paulmck)
- Convert se_portal_group->tpg_lun_list[] to RCU hlist (nab + hch +
paulmck)
- Simplify target backend driver registration (hch)
- Consolidate + simplify target backend attribute implementations
(hch + nab)
- Subsume se_port + t10_alua_tg_pt_gp_member into se_lun (hch)
- Drop lun_sep_lock for se_lun->lun_se_dev RCU usage (hch + nab)
- Drop unnecessary core_tpg_register TFO parameter (nab)
- Use 64-bit LUNs tree-wide (hannes)
- Drop left-over TARGET_MAX_LUNS_PER_TRANSPORT limit (hannes)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (76 commits)
target: Bump core version to v5.0
target: remove target_core_configfs.h
target: remove unused TARGET_CORE_CONFIG_ROOT define
target: consolidate version defines
target: implement WRITE_SAME with UNMAP bit using ->execute_unmap
target: simplify UNMAP handling
target: replace se_cmd->execute_rw with a protocol_data field
target/user: Fix inconsistent kmap_atomic/kunmap_atomic
target: Send UA when changing LUN inventory
target: Send UA upon LUN RESET tmr completion
target: Send UA on ALUA target port group change
target: Convert se_lun->lun_deve_lock to normal spinlock
target: use 'se_dev_entry' when allocating UAs
target: Remove 'ua_nacl' pointer from se_ua structure
target_core_alua: Correct UA handling when switching states
xen-scsiback: Fix compile warning for 64-bit LUN
target: Remove TARGET_MAX_LUNS_PER_TRANSPORT
target: use 64-bit LUNs
target: Drop duplicate + unused se_dev_check_wce
target: Drop unnecessary core_tpg_register TFO parameter
...
Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNobIACgkQMUfUDdst+ylXtQCgwTnzFBzly+3h1Npa2CWkr/Lw
TWAAn31qEP28MLjm8iVJLNPwdVd2kt1w
=hrdz
-----END PGP SIGNATURE-----
Merge tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (175 commits)
usb: dwc3: Use ASCII space in Kconfig
usb: chipidea: add work-around for Marvell HSIC PHY startup
usb: chipidea: allow multiple instances to use default ci_default_pdata
dt-bindings: Consolidate ChipIdea USB ci13xxx bindings
phy: add Marvell HSIC 28nm PHY
phy: Add Marvell USB 2.0 OTG 28nm PHY
dt-bindings: Add Marvell PXA1928 USB and HSIC PHY bindings
USB: ssb: use devm_kzalloc
USB: ssb: fix error handling in ssb_hcd_create_pdev()
usb: isp1760: check for null return from kzalloc
cdc-acm: Add support of ATOL FPrint fiscal printers
usb: chipidea: usbmisc_imx: Remove unneeded semicolon
USB: usbtmc: add device quirk for Rigol DS6104
USB: serial: mos7840: Use setup_timer
phy: twl4030-usb: add ABI documentation
phy: twl4030-usb: remove incorrect pm_runtime_get_sync() in probe function.
phy: twl4030-usb: remove pointless 'suspended' test in 'suspend' callback.
phy: twl4030-usb: make runtime pm more reliable.
drivers:usb:fsl: Fix compilation error for fsl ehci drv
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
...
This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There are also one new driver: the Cisco snic; the advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions).
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJViKWdAAoJEDeqqVYsXL0MAr8IAMmlA6HBVjMJJFCEOY9corHj
e70MNQa7LUgf+JCdOtzGcvHXTiFFd4IHZAwXUJAnsC4IU2QWEfi1bjUTErlqBIGk
LoZlXXpEHnFpmWot3OluOzzcGcxede8rVgPiKWVVdojIngBC2+LL/i2vPCJ84ri9
WCVlk6KBvWZXuU6JuOKAb2FO9HOX7Q61wuKAMast2Qc6RNc2ksgc7VbstsITqzZ9
FVEsjmQ5lqUj+xdxBpiUOdUpc22IJ4VcpBgQ2HrThvg6vf4aq937RJ/g4vi/g0SU
Utk0a3bUw1H/WnYAfJVFx83nVEsS/954Z7/ERDg1sjlfLYwQtQnpov0XIbPIbZU=
=k9IT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There is also one new driver: the Cisco snic. The advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (156 commits)
snic: driver for Cisco SCSI HBA
qla2xxx: Fix indentation
qla2xxx: Comment out unreachable code
fusion: remove dead MTRR code
advansys: fix compilation errors and warnings when CONFIG_PCI is not set
mptsas: fix depth param in scsi_track_queue_full
megaraid: fix irq setup process regression
lpfc: Update version to 10.7.0.0 for upstream patch set.
lpfc: Fix to drop PLOGIs from fabric node till LOGO processing completes
lpfc: Fix scsi task management error message.
lpfc: Fix cq_id masking problem.
lpfc: Fix scsi prep dma buf error.
lpfc: Add support for using block multi-queue
lpfc: Devices are not discovered during takeaway/giveback testing
lpfc: Fix vport deletion failure.
lpfc: Check for active portpeerbeacon.
lpfc: Update driver version for upstream patch set 10.6.0.1.
lpfc: Change buffer pool empty message to miscellaneous category
lpfc: Fix incorrect log message reported for empty FCF record.
lpfc: Fix rport leak.
...
This patch drops unnecessary target_core_fabric_ops parameter usage
for core_tpg_register() during fabric driver TFO->fabric_make_tpg()
se_portal_group creation callback execution.
Instead, use the existing se_wwn->wwn_tf->tf_ops pointer to ensure
fabric driver is really using the same TFO provided at module_init
time.
Also go ahead and drop the forward TFO declarations tree-wide, and
handling the special case for iscsi-target discovery TPG.
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This resolves a merge issue in musb_core.c and we want the fixes that
were in Linus's tree in this branch as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only include SCSI initiator header files in target code that needs
these header files, namely the SCSI pass-through code and the tcm_loop
driver. Change SCSI_SENSE_BUFFERSIZE into TRANSPORT_SENSE_BUFFER in
target code because the former is intended for initiator code and the
latter for target code. With this patch the only initiator include
directives in target code that remain are as follows:
$ git grep -nHE 'include .scsi/(scsi.h|scsi_host.h|scsi_device.h|scsi_cmnd.h)' drivers/target drivers/infiniband/ulp/{isert,srpt} drivers/usb/gadget/legacy/tcm_*.[ch] drivers/{vhost,xen} include/{target,trace/events/target.h}
drivers/target/loopback/tcm_loop.c:29:#include <scsi/scsi.h>
drivers/target/loopback/tcm_loop.c:31:#include <scsi/scsi_host.h>
drivers/target/loopback/tcm_loop.c:32:#include <scsi/scsi_device.h>
drivers/target/loopback/tcm_loop.c:33:#include <scsi/scsi_cmnd.h>
drivers/target/target_core_pscsi.c:39:#include <scsi/scsi_device.h>
drivers/target/target_core_pscsi.c:40:#include <scsi/scsi_host.h>
drivers/xen/xen-scsiback.c:52:#include <scsi/scsi_host.h> /* SG_ALL */
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Jqzf
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.2 merge window
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
Simplify target core and target drivers by storing the task tag
a.k.a. command identifier inside struct se_cmd.
For several transports (e.g. SRP) tags are 64 bits wide.
Hence add support for 64-bit tags.
(Fix core_tmr_abort_task conversion spec warnings - nab)
(Fix up usb-gadget to use 16-bit tags - HCH + bart)
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that struct se_portal_group contains a protocol identifier field we can
take all the code to format an parse protocol identifiers in CDBs into common
code instead of leaving this to low-level drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that we store the protocol identifier in the tpg structure we don't
need this method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove the unneeded fabric_ptr argument, and change the type argument
to pass in a SPC protocol identifier.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
By always allocating and adding, respectively removing and freeing
the se_node_acl structure in core code we can remove tons of repeated
code in the init_nodeacl and drop_nodeacl routines. Additionally
this now respects the get_default_queue_depth method in this code
path as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All fabric drivers except for iSCSI always return 1, so implement
that as default behavior.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Except for the embedded struct se_node_acl none of the fields were
ever used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes the following build warnings:
drivers/usb/gadget/udc/atmel_usba_udc.c:2207:12: warning:
‘usba_udc_suspend’ defined but not used [-Wunused-function] static int
usba_udc_suspend(struct device *dev)
drivers/usb/gadget/udc/atmel_usba_udc.c:2236:12: warning:
‘usba_udc_resume’ defined but not used [-Wunused-function] static int
usba_udc_resume(struct device *dev)
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following build warning:
drivers/usb/gadget/udc/atmel_usba_udc.c:707:2: warning: format ‘%x’
expects argument of type ‘unsigned int’, but argument 4 has type
‘dma_addr_t’ [-Wformat=]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Gadget must be informed about disconnection when pullup is removed.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reset configuration in ep_cfg on disable to physically disable the
endpoint.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB3380 GPEP can be used in IN and OUT directions however, both
directions should use same endpoint address. Fulfil this requirement
by mapping usb endpoint to hardware endpoint with the same address.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB3380 enhanced mode allows GPEP to be used in both IN and OUT
directions. However, IN and OUT endpoints must use same USB endpoint
address (bEndpointAddress). Fix this by setting the ep_cfg.ep_number
during initialization and keep it in net2280_enable()
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB3380 in enhanced mode has 4 IN and 4 OUT endpoints. Check
interrupts for all of them.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Default 0 value can result in unintentional zlp for IN endpoints.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB3380 ep_cfg.direction bit is reserved in enhanced mode. Don't set
it.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If ep->dma is set, abort_dma() takes care of dma clean-up. If ep->dma
is not set, unconditionally reset dma channel.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sequence number can be out of sync if endpoint is disabled after some
data transfers and enabled again. Reset it to stay in sync with host.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ffs_closed can race with configfs_rmdir which will call config_item_release, so
add an extra check to avoid calling the unregister_gadget_item with an null
gadget item.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
when copying to iter the size can be different then the iov count,
the check for full iov is wrong and make any read on request which
is not the exactly size of iov to return -EFAULT.
So, just check the success of the copy.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Not checking config_ep_by_speed could lead to a kernel
NULL pointer dereference error in usb_ep_enable
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Originally FFS_FL_CALL_CLOSED_CALLBACK flag has been used to
indicate if we should call ffs_closed_callback().
Commit 4b187fceec ("usb: gadget: FunctionFS: add devices
management code") changed its semantic to indicate if we should
call ffs_closed() function which does a little bit more.
This situation leads to:
[ 122.362269] ------------[ cut here ]------------
[ 122.362287] WARNING: CPU: 2 PID: 2384 at drivers/usb/gadget/function/f_fs.c:3417 ffs_ep0_write+0x730/0x810 [usb_f_fs]()
[ 122.362292] Modules linked in:
[ 122.362555] CPU: 2 PID: 2384 Comm: adbd Tainted: G W 4.1.0-0.rc4.git0.1.1.fc22.i686 #1
[ 122.362561] Hardware name: To be filled by O.E.M. To be filled by O.E.M./Aptio CRB, BIOS 5.6.5 07/25/2014
[ 122.362567] c0d1f947 415badfa 00000000 d1029e64 c0a86e54 00000000 d1029e94 c045b937
[ 122.362584] c0c37f94 00000002 00000950 f9b313d4 00000d59 f9b2ebf0 f9b2ebf0 fffffff0
[ 122.362600] 00000003 deb53d00 d1029ea4 c045ba42 00000009 00000000 d1029f08 f9b2ebf0
[ 122.362617] Call Trace:
[ 122.362633] [<c0a86e54>] dump_stack+0x41/0x52
[ 122.362645] [<c045b937>] warn_slowpath_common+0x87/0xc0
[ 122.362658] [<f9b2ebf0>] ? ffs_ep0_write+0x730/0x810 [usb_f_fs]
[ 122.362668] [<f9b2ebf0>] ? ffs_ep0_write+0x730/0x810 [usb_f_fs]
[ 122.362678] [<c045ba42>] warn_slowpath_null+0x22/0x30
[ 122.362689] [<f9b2ebf0>] ffs_ep0_write+0x730/0x810 [usb_f_fs]
[ 122.362702] [<f9b2e4c0>] ? ffs_ep0_read+0x380/0x380 [usb_f_fs]
[ 122.362712] [<c05a1c1f>] __vfs_write+0x2f/0x100
[ 122.362722] [<c05a42f2>] ? __sb_start_write+0x52/0x110
[ 122.362731] [<c05a2534>] vfs_write+0x94/0x1b0
[ 122.362740] [<c0a8a1c0>] ? mutex_lock+0x10/0x30
[ 122.362749] [<c05a2f41>] SyS_write+0x51/0xb0
[ 122.362759] [<c0a8c71f>] sysenter_do_call+0x12/0x12
[ 122.362766] ---[ end trace 0673d3467cecf8db ]---
in some cases (reproduction path below). This commit get back
semantic of that flag and ensures that ffs_closed() is called
always when needed but ffs_closed_callback() is called only
if this flag is set.
Reproduction path:
Compile kernel without any UDC driver or bound some gadget
to existing one and then:
$ modprobe g_ffs
$ mount none -t functionfs mount_point
$ ffs-example mount_point
This will fail with -ENODEV as there is no udc.
$ ffs-example mount_point
This will fail with -EBUSY because ffs_data has not been
properly cleaned up.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Returning non-zero value from ready callback makes ffs instance
return error from writing strings and enter FFS_CLOSING state.
This means that this this function is not truly ready and
close callback will not be called. This commit fix
ffs_ready_callback() to undo all side effects of this function
in case of error.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For some reason the code has always been disabling pullup
when asked to do the opposite. According to surrounding code
and gadget API this seems to be a mistake. This fix allows
UDC to be detected by host controller on recent kernels.
Signed-off-by: Sergiy Kibrik <sakib@meta.ua>
Signed-off-by: Felipe Balbi <balbi@ti.com>
rndis_get_nr() returns either a non-negative value on success
or a negative value on failure. In case of failure an error code
is returned to the caller of rndis_register().
If the "i" is unsigned, the information about error from rndis_get_nr()
is lost. If there is no error but rndis_get_nr() returns a value greater
than 256 the least significant bits of i are zero effectively limiting the
number of configs to 256.
This patch fixes that.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If CONFIG_USB_GADGET_DEBUG_FILES is set then a block is opened and inside
it there is a local variable "i" which hides the "i" local to the
rndis_deregister(). Consequently, a random value is formatted
into the "name" buffer.
This patch removes the block-local i.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The patch:
83210e59ee
usb: gadget: rndis: use rndis_params instead of configNr
should change all invocations of rndis_signal_(dis)connect().
This patch fixes that.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Al Viro <viro@zeniv.linux.org.uk>
CC: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
CC: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
RNDIS function has a limitation on the number of allowed instances.
So far it has been RNDIS_MAX_CONFIGS, which happens to be one.
In order to eliminate this kind of arbitrary limitation we should not
preallocate a predefined (RNDIS_MAX_CONFIGS) array of struct rndis_params
instances but instead allow allocating them on demand.
This patch allocates struct rndis_params on demand in rndis_register().
Coversly, the structure is free()'d in rndis_deregister().
If CONFIG_USB_GADGET_DEBUG_FILES is set, the proc files are created which
is the same behaviour as before, but the moment of creation is delayed
until struct rndis_params is actually allocated.
rnids_init() and rndis_exit() have nothing to do, so they are eliminated.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Don't use a space between function name and parameter list opening bracket.
All other functions in this file comply wich checkpatch rules.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
RNDIS function has a limitation on the number of allowed instances.
So far it has been RNDIS_MAX_CONFIGS, which happens to be one.
In order to eliminate this kind of arbitrary limitation we should not
preallocate a predefined (RNDIS_MAX_CONFIGS) array of struct rndis_params
instances but instead allow allocating them on demand.
This patch prepares the elimination of the said limit by converting all the
functions which accept rndis config number to accept a pointer to the
actual struct rndis_params. Consequently, rndis_register() returns
a pointer to a corresponding struct rndis_params instance. The pointer
is then always used by f_rndis.c instead of config number when it talks
to rndis.c API.
A nice side-effect of the changes is that many lines of code in rndis.c
become shorter and fit in 80 columns.
If a function prototype changes in rndis.h a style cleanup is made
at the same time, otherwise checkpatch complains that the patch
has style problems.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using unnecessary static char buffers isn't good.
Use the %pV extension instead.
Miscellanea:
o the dprintk return value is unused, make it void
o add __printf format and argument verification
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A recent change introduced a link error for the composite
printer gadget driver:
`printer_unbind' referenced in section `.ref.data' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
Evidently the unbind function should not be marked __exit here,
because it is called through a callback pointer that is not necessarily
discarded, __composite_unbind() is indeed called from the error path of
composite_bind(), which can never work for a built-in driver.
Looking at the surrounding code, I found the same problem in all other
composite gadget drivers in both the bind and unbind functions, as
well as the udc platform driver 'remove' functions. Those will break
if anyone uses the 'unbind' sysfs attribute to detach a device from a
built-in driver.
This patch removes the incorrect annotations from all the gadget
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a single thread is sending out data over the gadget serial port,
gs_start_tx() will be called both from the sender context and from the
write completion. Since the port lock is released before the packet is
queued, the order in which the URBs are submitted is not guaranteed.
E.g.
sending thread completion (interrupt)
gs_write()
LOCK
gs_write_complete()
LOCK (wait)
gs_start_tx()
req1 = list_entry(pool->next)
UNLOCK
LOCK (acquired)
gs_start_tx()
req2 = list_entry(pool->next)
UNLOCK
usb_ep_queue(req2)
usb_ep_queue(req1)
I.e., req2 is submitted before req1 but it contains the data that
comes after req1.
To reproduce, use SMP with sending thread and completion pinned to
different CPUs, or use PREEMPT_RT, and add the following delay just
before the call to usb_ep_queue():
if (port->write_started > 0 && !list_empty(pool))
udelay(1000);
To work around this problem, make sure that only one thread is running
through the gs_start_tx() loop with an extra flag write_busy. Since
gs_start_tx() is always called with the port lock held, no further
synchronisation is needed. The original caller will continue through
the loop when the request was successfully submitted.
Signed-off-by: Philip Oberstaller <Philip.Oberstaller@septentrio.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we have multiple instances of hid function, each of
them may have different report descriptor, also their
length may be different.
Currently we are using static hidg_desc varable which
is being filled in hidg_bind(). Then we send its content
to host in hidg_setup() function. This content may
have been already overwriten if another instance
has executed hidg_bind().
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
devm_ioremap_resource() returns IOMEM_ERR_PTR() and it never
returns NULL, fix the check to prevent access to invalid
virtual address.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity in target land the last months.
The highlights include:
- Convert fabric drivers tree-wide to target_register_template() (hch
+ bart)
- iser-target hardening fixes + v1.0 improvements (sagi)
- Convert iscsi_thread_set usage to kthread.h + kill
iscsi_target_tq.c (sagi + nab)
- Add support for T10-PI WRITE_STRIP + READ_INSERT operation (mkp +
sagi + nab)
- DIF fixes for CONFIG_DEBUG_SG=y + UNMAP file emulation (akinobu +
sagi + mkp)
- Extended TCMU ABI v2 for future BIDI + DIF support (andy + ilias)
- Fix COMPARE_AND_WRITE handling for NO_ALLLOC drivers (hch + nab)
Thanks to everyone who contributed this round with new features,
bug-reports, fixes, cleanups and improvements.
Looking forward, it's currently shaping up to be a busy v4.2 as well"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (69 commits)
target: Put TCMU under a new config option
target: Version 2 of TCMU ABI
target: fix tcm_mod_builder.py
target/file: Fix UNMAP with DIF protection support
target/file: Fix SG table for prot_buf initialization
target/file: Fix BUG() when CONFIG_DEBUG_SG=y and DIF protection enabled
target: Make core_tmr_abort_task() skip TMFs
target/sbc: Update sbc_dif_generate pr_debug output
target/sbc: Make internal DIF emulation honor ->prot_checks
target/sbc: Return INVALID_CDB_FIELD if DIF + sess_prot_type disabled
target: Ensure sess_prot_type is saved across session restart
target/rd: Don't pass incomplete scatterlist entries to sbc_dif_verify_*
target: Remove the unused flag SCF_ACK_KREF
target: Fix two sparse warnings
target: Fix COMPARE_AND_WRITE with SG_TO_MEM_NOALLOC handling
target: simplify the target template registration API
target: simplify target_xcopy_init_pt_lun
target: remove the unused SCF_CMD_XCOPY_PASSTHROUGH flag
target/rd: reduce code duplication in rd_execute_rw()
tcm_loop: fixup tpgt string to integer conversion
...
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
hexdump: avoid warning in test function
fs: take i_mutex during prepare_binprm for set[ug]id executables
smp: Fix error case handling in smp_call_function_*()
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
Break up monolithic iommu table/lock into finer graularity pools and lock
sparc: Revert generic IOMMU allocator.
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
Bluetooth: hidp: Fix regression with older userspace and flags validation
config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
...
That solves several merge conflicts:
Documentation/DocBook/media/v4l/subdev-formats.xml
Documentation/devicetree/bindings/vendor-prefixes.txt
drivers/staging/media/mn88473/mn88473.c
include/linux/kconfig.h
include/uapi/linux/media-bus-format.h
The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.
Pull second vfs update from Al Viro:
"Now that net-next went in... Here's the next big chunk - killing
->aio_read() and ->aio_write().
There'll be one more pile today (direct_IO changes and
generic_write_checks() cleanups/fixes), but I'd prefer to keep that
one separate"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
->aio_read and ->aio_write removed
pcm: another weird API abuse
infinibad: weird APIs switched to ->write_iter()
kill do_sync_read/do_sync_write
fuse: use iov_iter_get_pages() for non-splice path
fuse: switch to ->read_iter/->write_iter
switch drivers/char/mem.c to ->read_iter/->write_iter
make new_sync_{read,write}() static
coredump: accept any write method
switch /dev/loop to vfs_iter_write()
serial2002: switch to __vfs_read/__vfs_write
ashmem: use __vfs_read()
export __vfs_read()
autofs: switch to __vfs_write()
new helper: __vfs_write()
switch hugetlbfs to ->read_iter()
coda: switch to ->read_iter/->write_iter
ncpfs: switch to ->read_iter/->write_iter
net/9p: remove (now-)unused helpers
p9_client_attach(): set fid->uid correctly
...
Pull vfs update from Al Viro:
"Part one:
- struct filename-related cleanups
- saner iov_iter_init() replacements (and switching the syscalls to
use of those)
- ntfs switch to ->write_iter() (Anton)
- aio cleanups and splitting iocb into common and async parts
(Christoph)
- assorted fixes (me, bfields, Andrew Elble)
There's a lot more, including the completion of switchover to
->{read,write}_iter(), d_inode/d_backing_inode annotations, f_flags
race fixes, etc, but that goes after #for-davem merge. David has
pulled it, and once it's in I'll send the next vfs pull request"
* 'for-linus-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (35 commits)
sg_start_req(): use import_iovec()
sg_start_req(): make sure that there's not too many elements in iovec
blk_rq_map_user(): use import_single_range()
sg_io(): use import_iovec()
process_vm_access: switch to {compat_,}import_iovec()
switch keyctl_instantiate_key_common() to iov_iter
switch {compat_,}do_readv_writev() to {compat_,}import_iovec()
aio_setup_vectored_rw(): switch to {compat_,}import_iovec()
vmsplice_to_user(): switch to import_iovec()
kill aio_setup_single_vector()
aio: simplify arguments of aio_setup_..._rw()
aio: lift iov_iter_init() into aio_setup_..._rw()
lift iov_iter into {compat_,}do_readv_writev()
NFS: fix BUG() crash in notify_change() with patch to chown_common()
dcache: return -ESTALE not -EBUSY on distributed fs race
NTFS: Version 2.1.32 - Update file write from aio_write to write_iter.
VFS: Add iov_iter_fault_in_multipages_readable()
drop bogus check in file_open_root()
switch security_inode_getattr() to struct path *
constify tomoyo_realpath_from_path()
...
Instead of calling target_fabric_configfs_init() +
target_fabric_configfs_register() / target_fabric_configfs_deregister()
target_fabric_configfs_free() from every target driver, rewrite the API
so that we have simple register/unregister functions that operate on
a const operations vector.
This patch also fixes a memory leak in several target drivers. Several
target drivers namely called target_fabric_configfs_deregister()
without calling target_fabric_configfs_free().
A large part of this patch is based on earlier changes from
Bart Van Assche <bart.vanassche@sandisk.com>.
(v2: Add a new TF_CIT_SETUP_DRV macro so that the core configfs code
can declare attributes as either core only or for drivers)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All places outside of core VFS that checked ->read and ->write for being NULL or
called the methods directly are gone now, so NULL {read,write} with non-NULL
{read,write}_iter will do the right thing in all cases.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix using the bare numbers to set the 'bDescriptorType' field of the Hub
Descriptors while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
struct kiocb now is a generic I/O container, so move it to fs.h.
Also do a #include diet for aio.h while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=U+M2
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.1 merge window
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If f_printer is selected without legacy g_printer, it should
depend on USB_CONFIGFS which pulls in libcomposite.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here's a number of USB and PHY driver fixes for 4.0-rc5. Largest thing
here is a revert of a gadget function driver patch that removes 500
lines of code. Other than that, it's a number of reported bugs fixes
and new quirk/id entries.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlUOmk4ACgkQMUfUDdst+ym94wCdGs4iVQbrTA9p+561H8jhCCxh
79oAn3y24kql3ob9/iuV6+N36+HQsp+0
=IPei
-----END PGP SIGNATURE-----
Merge tag 'usb-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY driver fixes from Greg KH:
"Here's a number of USB and PHY driver fixes for 4.0-rc5.
The largest thing here is a revert of a gadget function driver patch
that removes 500 lines of code. Other than that, it's a number of
reported bugs fixes and new quirk/id entries.
All have been in linux-next for a while"
* tag 'usb-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: common: otg-fsm: only signal connect after switching to peripheral
uas: Add US_FL_NO_ATA_1X for Initio Corporation controllers / devices
USB: ehci-atmel: rework clk handling
MAINTAINERS: add entry for USB OTG FSM
usb: chipidea: otg: add a_alt_hnp_support response for B device
phy: omap-usb2: Fix missing clk_prepare call when using old dt name
phy: ti/omap: Fix modalias
phy: core: Fixup return value of phy_exit when !pm_runtime_enabled
phy: miphy28lp: Convert to devm_kcalloc and fix wrong sizof
phy: miphy365x: Convert to devm_kcalloc and fix wrong sizeof
phy: twl4030-usb: Remove redundant assignment for twl->linkstat
phy: exynos5-usbdrd: Fix off-by-one valid value checking for args->args[0]
phy: Find the right match in devm_phy_destroy()
phy: rockchip-usb: Fixup rockchip_usb_phy_power_on failure path
phy: ti-pipe3: Simplify ti_pipe3_dpll_wait_lock implementation
phy: samsung-usb2: Remove NULL terminating entry from phys array
phy: hix5hd2-sata: Check return value of platform_get_resource
phy: exynos-dp-video: Kill exynos_dp_video_phy_pwr_isol function
Revert "usb: gadget: zero: Add support for interrupt EP"
Revert "xhci: Clear the host side toggle manually when endpoint is 'soft reset'"
...
Pull SCSI target fixes from Nicholas Bellinger:
"Here are current target-pending fixes for v4.0-rc5 code that have made
their way into the queue over the last weeks.
The fixes this round include:
- Fix long-standing iser-target logout bug related to early
conn_logout_comp completion, resulting in iscsi_conn use-after-tree
OOpsen. (Sagi + nab)
- Fix long-standing tcm_fc bug in ft_invl_hw_context() failure
handing for DDP hw offload. (DanC)
- Fix incorrect use of unprotected __transport_register_session() in
tcm_qla2xxx + other single local se_node_acl fabrics. (Bart)
- Fix reference leak in target_submit_cmd() -> target_get_sess_cmd()
for ack_kref=1 failure path. (Bart)
- Fix pSCSI backend ->get_device_type() statistics OOPs with
un-configured device. (Olaf + nab)
- Fix virtual LUN=0 target_configure_device failure OOPs at modprobe
time. (Claudio + nab)
- Fix FUA write false positive failure regression in v4.0-rc1 code.
(Christophe Vu-Brugier + HCH)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: do not reject FUA CDBs when write cache is enabled but emulate_write_cache is 0
target: Fix virtual LUN=0 target_configure_device failure OOPs
target/pscsi: Fix NULL pointer dereference in get_device_type
tcm_fc: missing curly braces in ft_invl_hw_context()
target: Fix reference leak in target_get_sess_cmd() error path
loop/usb/vhost-scsi/xen-scsiback: Fix use of __transport_register_session
tcm_qla2xxx: Fix incorrect use of __transport_register_session
iscsi-target: Avoid early conn_logout_comp for iser connections
Revert "iscsi-target: Avoid IN_LOGOUT failure case for iser-target"
target: Disallow changing of WRITE cache/FUA attrs after export
This patch changes loopback, usb-gadget, vhost-scsi and xen-scsiback
fabric code to invoke transport_register_session() instead of the
unprotected flavour, to ensure se_tpg->session_lock is taken when
adding new session list nodes to se_tpg->tpg_sess_list.
Note that since these four fabric drivers already hold their own
internal TPG mutexes when accessing se_tpg->tpg_sess_list, and
consist of a single se_session created through configfs attribute
access, no list corruption can currently occur.
So for correctness sake, go ahead and use the se_tpg->session_lock
protected version for these four fabric drivers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Change from using the __raw IO accesors to the endian agnostic versions
of readl/writel_relaxed when not on AVR32. This fixes issues with running
big endian on ARMv7.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
--
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Felipe Balbi <balbi@ti.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The seq_printf/seq_puts/seq_putc return values, because they
are frequently misused, will eventually be converted to void.
See: commit 1f33c41c03 ("seq_file: Rename seq_overflow() to
seq_has_overflowed() and make public")
Miscellanea:
o Coalesce formats, realign arguments
o Create static functions for statement expression macros
o Use c90 style comments instead of c99
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit updates udc core vbus status, and try to connect
or disconnect gadget.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of iterate to find usb_udc according to usb_gadget, this
way is easier.
Alan Stern suggests this way too:
http://marc.info/?l=linux-usb&m=142168496528894&w=2
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of manual device_create_file() and device_remove_file() calls,
assign the static attribute groups to the lun device to register.
The RO or RW permissions for some entries are decided in is_visible
callback. This simplifies the code (also the logic) and avoids the
possible races, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull gadgetfs fixes from Al Viro:
"Assorted fixes around AIO on gadgetfs: leaks, use-after-free, troubles
caused by ->f_op flipping"
* 'gadget' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
gadgetfs: really get rid of switching ->f_op
gadgetfs: get rid of flipping ->f_op in ep_config()
gadget: switch ep_io_operations to ->read_iter/->write_iter
gadgetfs: use-after-free in ->aio_read()
gadget/function/f_fs.c: switch to ->{read,write}_iter()
gadget/function/f_fs.c: use put iov_iter into io_data
gadget/function/f_fs.c: close leaks
move iov_iter.c from mm/ to lib/
new helper: dup_iter()
Most callers in the kernel want to perform synchronous file I/O, but
still have to bloat the stack with a full struct kiocb. Split out
the parts needed in filesystem code from those in the aio code, and
only allocate those needed to pass down argument on the stack. The
aio code embedds the generic iocb in the one it allocates and can
easily get back to it by using container_of.
Also add a ->ki_complete method to struct kiocb, this is used to call
into the aio code and thus removes the dependency on aio for filesystems
impementing asynchronous operations. It will also allow other callers
to substitute their own completion callback.
We also add a new ->ki_flags field to work around the nasty layering
violation recently introduced in commit 5e33f6 ("usb: gadget: ffs: add
eventfd notification about ffs events").
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
USB_DIR_OUT happens to be zero, so the result of bitwise and is always 0.
Consequently, break will never happen in the SOFT_RESET case.
This patch uses a compatible condition with a non-zero USB_DIR_IN,
which might or might not evaluate to zero.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was a missing goto so we free "opts" and then dereference it.
Fixes: ee1cd515e8 ('usb: gadget: printer: add configfs support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"num" is a u16 so it can't go higher than 65535. kstrtou16() has a
range check built in so this is already handled.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use %ps for actual addresses, otherwise you'll get bad output
on arches like ppc64 where %pf expects a function descriptor
(which is not what __builtin_return_address returns).
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: linux-usb@vger.kernel.org
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
udc is then checked for NULL, if NULL, it is then dereferenced as
udc->dev, it is found using Coccinelle.
We simplify the code to fix this problem, and we delete some conditions
at if {} which will never be met.
Reported-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Reported-by : Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function usb_ep_disable() causes completion of all requests queued
for given endpoint, so there is no need to dequeue them after endpoint
disabling.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Not everybody uses a utf8 locale (unfortunately), so let's avoid
non-ascii characters in the kernel log. Replace the 3-byte utf8
sequence with a 3-byte ascii equivalent.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch add suspend/resume with wakeup support for Atmel USBA.
On suspend: We stay continuously clocked if Vbus signal is not
available. If Vbus signal is available we set the Vbus signal as a wake
up source then we stop the USBA itself and all clocks used by USBA.
On resume: We recover clocks and USBA if we stopped them. If a device is
currently connected at resume time we enable the controller.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If USB PLL is not necessary for other USB drivers (e.g. OHCI and EHCI)
we will reduce power consumption by switching off the USB PLL if no USB
Host is currently connected to this USB Device.
We are using Vbus GPIO signal to detect Host presence. If Vbus signal is
not available then the device stays continuously clocked.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Vbus IRQ handler needs a started UDC driver to work because it uses
udc->driver, which is set by the UDC start handler. The previous way
chosen was to return from interrupt if udc->driver is NULL using a
spinlock around the check.
We now request an auto disabled (IRQ_NOAUTOEN) Vbus signal IRQ instead
of an auto enabled IRQ followed by disable_irq(). This way we remove the
very small timeslot of enabled IRQ which existed previously between
request() and disable(). We don't need anymore to check if udc->driver
is NULL in IRQ handler.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If vbus gpio is high at init, we should set vbus_prev to true
accordingly to the current vbus state. Without that, we skip the first
vbus interrupt because the saved vbus state is not consistent.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
replace numeric value with TYPE_NO_LUN (defined in <scsi/scsi.h>)
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fix some spelling typo found in gadget.xml.
It is because this file is generated from comments in sources,
I had to fix comments in the source, instead of xml file itself.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit ef11982dd7.
That commit creates a problem for some UDCs (at least musb)
where it allocates an endpoints with a 64-byte FIFO, but later
tries to use that same FIFO for 1024-byte packets.
Before implementing this, composite framework needs to be
modified so we only allocate endpoints after we know negotiated
speed, however that needs quite a bit of extra work.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for configfs interface so that f_printer can be used as a
component of usb gadgets composed with it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Substitute some boilerplate code with a dedicated macro.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no old interface users left, so it can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The goal is to remove the old function interface, so its (only) user
must be converted to the new interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to add configfs support, a usb function must be converted to use
the new interface. This patch converts the function to the new interface
and provides backward compatiblity layer, which can be removed after
all its users are converted to use the new interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The legacy printer gadget now contains both a reusable printer function
and legacy gadget proper implementations interwoven, but logically
separate. This patch factors out a reusable f_printer.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
With all the obstacles removed it is possible to allow more than one
instance of the printer function. Since the function requires allocating
character device region, a maximum number of allowed instances is defined.
Such an approach is used in f_acm and in f_hid.
With multiple instances it does not make sense to depend on a
lock_printer_io member of a dynamically allocated (and destroyed) struct
printer_dev to clean up after all instances of the printer function.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Verify that a given usb_ctrlrequest is meant for printer function.
The following parts of the request are tested:
- bmRequestType:Data transfer direction
- bmRequestType:Type
- bmRequestType:Recipient
- bRequest
- wValue for bRequest 1 and 2
- wLength
Additionally, the request is considered meant for this function
iff the decoded interface number matches dev->interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Non-standard requests can encode the actual interface number in a
non-standard way. For example composite_setup() assumes
that it is w_index && 0xFF, but the printer function encodes the interface
number in a context-dependet way (either w_index or w_index >> 8).
This can lead to such requests being directed to wrong functions.
This patch adds req_match() method to usb_function. Its purpose is to
verify that a given request can be handled by a given function.
If any function within a configuration provides the method and it returns
true, then it is assumed that the right function is found.
If a function uses req_match(), it should try as hard as possible to
determine if the request is meant for it.
If no functions in a configuration provide req_match or none of them
returns true, then fall back to the usual approach.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
5 uses of container_of() in the same context justify wrapping it
in a static inline function.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The printer_dev can be recovered from printer_func_unbind() function's
parameters.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The mutex is a legacy after semi-automatic Big Kernel Lock removal.
printer_open() does its own locking, so no need to duplicate it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Call gprinter_setup() from gadget's bind instead of module's init.
Call gprinter_cleaup() corerspondingly. This detaches printer function's
logic from legacy printer gadget's implementation.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Factor out gprinter_setup() and gprinter_cleanup() so that it is
easy to change the place they are called from.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to factor out a reusable f_printer, the function's code should
not use file global variables related to legacy printer gadget's
implementation.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to factor out a reusable f_printer.c, the code related to the
function should be placed in functions related to the function.
printer_cfg_unbind() becomes empty, so it is removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conversion to the new function interface requires splitting a
<something>_bind_config() function into two parts: allocation of
container_of struct usb_function and invocation of usb_add_function().
This patch moves the latter to the end of the f_printer_bind_config()
in order to enable conversion to the new interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to factor out a reusable f_printer.c, the code related to the
function should be placed in functions related to the function.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Follow the convention of distributing source code between
<something>_do_config() and <something>_bind_config().
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Legacy gadgets, before converting them to the new function framework,
used to use the name <something>_do_config() for usb_add_config()'s
callback.
This patch changes the name so that it is easier to follow
the convention.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The pdev member of struct printer_dev is not used outside
printer_bind_config(), so it can just as well be a local variable there.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If cdev_add() in printer_bind_config() fails, care is taken to
reverse the effects of initializations completed until the fail
happens. But if printer_req_alloc() fails, it is just one of the
two lists that is cleaned up while the effects of cdev_add()
and device_create() are not reverted.
This patch changes error handling so that at least as much cleanup is done
as when a failure happens before printer_req_alloc() invocations.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whenever the "goto fail" branch is taken, the effect of usb_add_function()
should be reverted.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
struct printer_dev contains 3 list heads: tx_reqs, rx_reqs and rx_buffers.
There is just one instance of this structure in the driver and it is
file static, and as such initialized with all zeros.
If device_create() or cdev_add() fails then "goto fail" branch is taken,
which results in printer_cfg_unbind() call. The latter checks if
tx_reqs, rx_reqs and rx_buffers lists are empty. The check for emptiness
is in fact a check whether the "next" member of struct list_head points
to the head of the list. But the heads of the lists in question have
not been initialized yet and, as mentioned above, contain all zeros,
so list_empty() returns false and respective "while" loop body starts
executing. Here, container_of() just subtracts the offset of a struct
usb_request member from an address of this same member, which results in
a value somewhere near 0 or 0xfff...ff. And the argument to list_del()
dereferences such a pointer which causes a disaster.
This patch moves respective INIT_LIST_HEAD() invocations to a point before
"goto fail" branch can be taken.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The unbind() method is optional is usb_composite_driver.
In this particular driver the method does nothing so it can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function-specific setup requests should be handled in such a way, that
apart from filling in the data buffer, the requests are also actually
enqueued: if function-specific setup is called from composte_setup(),
the "usb_ep_queue()" block of code in composite_setup() is skipped.
The printer function lacks this part and it results in e.g. get device id
requests failing: the host expects some response, the device prepares it
but does not equeue it for sending to the host, so the host finally asserts
timeout.
This patch adds enqueueing the prepared responses.
Cc: <stable@vger.kernel.org> # v3.4+
Fixes: 2e87edf49227: "usb: gadget: make g_printer use composite"
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If a non-standard request is processed and its parameters just happen
to match those of some standard request, the logic of composite_setup()
can be fooled, so don't even try any switch cases, just go to the
proper place where unknown requests are handled.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Silence the following warning:
drivers/usb/gadget/udc/net2280.c:3176:33: warning: context imbalance in
'handle_stat1_irqs' - unexpected unlock
Signed-off-by: Felipe Balbi <balbi@ti.com>
net2280_start can be called with pullup disabled. Don't set
softconnect flag in it. Let net2280_pullup handle the connection part.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Hopefully, these prints will help localize the problems faster.
[ balbi@ti.com: removed 2 unnecessary OOM error messages ]
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove fiforegs from struct net2280 and net2280_ep as it is unused.
By the way, ep->fiforegs = &dev->fiforegs[i] assignment is incorrect.
It should be ep->fiforegs = &dev->fiforegs[ne[i]], but it doesn't
matter now.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Each struct usb_ep added for net2280 can be used in either direction.
Whereas, each struct usb_ep for usb3380 has fixed direction. Use
ep_autoconf compatible names so that endpoint with correct direction
can be selected.
Name sequence is due to the logic in usb_reinit_338x() in ne[] and
ep_reg_addr[].
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The seq_printf return value, because it's frequently misused,
will eventually be converted to void.
See: commit 1f33c41c03 ("seq_file: Rename seq_overflow() to
seq_has_overflowed() and make public")
While there, simplify the error handler logic by returning
immediately and remove the unnecessary labels.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Final methods start with get_ready_ep(), which will fail unless we have
->state == STATE_EP_ENABLED. So they'd be failing just fine until that
first write() anyway. Let's do the following:
* get_ready_ep() gets a new argument - true when called from
ep_write_iter(), false otherwise.
* make it quiet when it finds STATE_EP_READY (no printk, that is;
the case won't be impossible after that change).
* when that new argument is true, treat STATE_EP_READY the same
way as STATE_EP_ENABLED (i.e. return zero and do not unlock).
* in ep_write_iter(), after success of get_ready_ep() turn
if (!usb_endpoint_dir_in(&epdata->desc)) {
into
if (epdata->state == STATE_EP_ENABLED &&
!usb_endpoint_dir_in(&epdata->desc)) {
- that logics only applies after config.
* have ep_config() take kernel-side buffer (i.e. use memcpy()
instead of copy_from_user() in there) and in the "let's call ep_io or
ep_aio" (again, in ep_write_iter()) add "... or ep_config() in case it's
not configured yet"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The V4L2 core will warn if this is not done. Unfortunately this driver
wasn't updated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of .ioctl use unlocked_ioctl. This allows us to finally remove
the old .ioctl op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Switch this driver over to the V4L2 core locking mechanism in preparation
for switching to unlocked_ioctl. Suggested by Laurent Pinchart.
This patch introduces a new mutex at the struct uvc_video level and
drops the old mutex at the queue level. The new lock is now used for all
ioctl locking and in the release file operation (the driver always has
to take care of locking in file operations, the core only serializes
ioctls).
Note that the mmap and get_unmapped_area file operations no longer take
a lock. Commit f035eb4e97 fixed a AB-BA
deadlock by moving all the locking down into vb2, so the mmap and
get_unmapped_area file operations should no longer do any locking before
calling into vb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The "Extended Compat ID OS Feature Descriptor Specification" does not
require the (sub)compatible ids to be NUL-terminated, because they
are placed in a fixed-size buffer and only unused parts of it should
contain NULs. If the buffer is fully utilized, there is no place for NULs.
Consequently, the code which uses desc->ext_compat_id never expects the
data contained to be NUL terminated.
If the compatible id is stored after sub-compatible id, and the compatible
id is full length (8 bytes), the (useless) NUL terminator overwrites the
first byte of the sub-compatible id.
If the sub-compatible id is full length (8 bytes), the (useless) NUL
terminator ends up out of the buffer. The situation can happen in the RNDIS
function, where the buffer is a part of struct f_rndis_opts. The next
member of struct f_rndis_opts is a mutex, so its first byte gets
overwritten. The said byte is a part of a mutex'es member which contains
the information on whether the muext is locked or not. This can lead to a
deadlock, because, in a configfs-composed gadget when a function is linked
into a configuration with config_usb_cfg_link(), usb_get_function()
is called, which then calls rndis_alloc(), which tries locking the same
mutex and (wrongly) finds it already locked.
This patch eliminates NUL terminating of the (sub)compatible id.
Cc: <stable@vger.kernel.org> # v3.16+
Fixes: da4243145fb1: "usb: gadget: configfs: OS Extended Compatibility descriptors support"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
uvc_v4l2.c:264:29: warning: symbol 'uvc_v4l2_ioctl_ops' was not declared. Should it be static?
uvc_v4l2.c:355:29: warning: symbol 'uvc_v4l2_fops' was not declared. Should it be static?
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
g_ffs.c:136:3: warning: symbol 'gfs_configurations' was not declared. Should it be static?
g_ffs.c:281:16: warning: Using plain integer as NULL pointer
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
uvc_video.c:283:5: warning: symbol 'uvcg_video_pump' was not declared. Should it be static?
uvc_video.c:342:5: warning: symbol 'uvcg_video_enable' was not declared. Should it be static?
uvc_video.c:381:5: warning: symbol 'uvcg_video_init' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
f_sourcesink.c:347:34: warning: symbol 'ss_int_source_comp_desc' was not declared. Should it be static?
f_sourcesink.c:365:34: warning: symbol 'ss_int_sink_comp_desc' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
f_uac2.c:57:12: warning: symbol 'uac2_name' was not declared. Should it be static?
f_uac2.c:637:36: warning: symbol 'in_clk_src_desc' was not declared. Should it be static?
f_uac2.c:649:36: warning: symbol 'out_clk_src_desc' was not declared. Should it be static?
f_uac2.c:661:39: warning: symbol 'usb_out_it_desc' was not declared. Should it be static?
f_uac2.c:675:39: warning: symbol 'io_in_it_desc' was not declared. Should it be static?
f_uac2.c:689:40: warning: symbol 'usb_in_ot_desc' was not declared. Should it be static?
f_uac2.c:703:40: warning: symbol 'io_out_ot_desc' was not declared. Should it be static?
f_uac2.c:716:34: warning: symbol 'ac_hdr_desc' was not declared. Should it be static?
f_uac2.c:754:34: warning: symbol 'as_out_hdr_desc' was not declared. Should it be static?
f_uac2.c:767:38: warning: symbol 'as_out_fmt1_desc' was not declared. Should it be static?
f_uac2.c:775:32: warning: symbol 'fs_epout_desc' was not declared. Should it be static?
f_uac2.c:785:32: warning: symbol 'hs_epout_desc' was not declared. Should it be static?
f_uac2.c:831:34: warning: symbol 'as_in_hdr_desc' was not declared. Should it be static?
f_uac2.c:844:38: warning: symbol 'as_in_fmt1_desc' was not declared. Should it be static?
f_uac2.c:852:32: warning: symbol 'fs_epin_desc' was not declared. Should it be static?
f_uac2.c:862:32: warning: symbol 'hs_epin_desc' was not declared. Should it be static?
f_uac2.c:1566:21: warning: symbol 'afunc_alloc' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warning:
f_hid.c:572:30: warning: symbol 'f_hidg_fops' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
f_phonet's ->set_alt() method will call usb_ep_disable()
potentially on an endpoint which is already disabled. That's
something the gadget/function driver must guarantee that it's
always balanced.
In order to balance the calls, just make sure the endpoint
was enabled before by means of checking the validity of
driver_data.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
AIO_PREAD requests call ->aio_read() with iovec on caller's stack, so if
we are going to access it asynchronously, we'd better get ourselves
a copy - the one on kernel stack of aio_run_iocb() won't be there
anymore. function/f_fs.c take care of doing that, legacy/inode.c
doesn't...
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull debugfs patches from Al Viro:
"debugfs patches, mostly to make it possible for something like tracefs
to be transparently automounted on given directory in debugfs.
New primitive in there is debugfs_create_automount(name, parent, func,
arg), which creates a directory and makes its ->d_automount() return
func(arg). Another missing primitive was debugfs_create_file_size() -
open-coded in quite a few places. Dave's patch adds it and converts
the open-code instances to calling it"
* 'debugfs_automount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
debugfs: Provide a file creation function that also takes an initial size
new primitive: debugfs_create_automount()
debugfs: split end_creating() into success and failure cases
debugfs: take mode-dependent parts of debugfs_get_inode() into callers
fold debugfs_mknod() into callers
fold debugfs_create() into caller
fold debugfs_mkdir() into caller
debugfs_mknod(): get rid useless arguments
fold debugfs_link() into caller
debugfs: kill __create_file()
debugfs: split the beginning and the end of __create_file() off
debugfs_{mkdir,create,link}(): get rid of redundant argument
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
This time around, much of this is for at91, with the bulk of it being syscon
and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=T7R2
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
This time around, much of this is for at91, with the bulk of it being
syscon and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
soc: ti: knav_qmss_queue: change knav_range_setup_acc_irq to static
soc: ti: knav_qmss_queue: makefile tweak to build as dynamic module
pcmcia: at91_cf: depend on !ARCH_MULTIPLATFORM
soc: ti: knav_qmss_queue: export API calls for use by user driver
of/platform: teardown DMA mappings on device destruction
usb: gadget: at91_udc: Allocate udc instance
usb: gadget: at91_udc: Update DT binding documentation
usb: gadget: at91_udc: Rework for multi-platform kernel support
usb: gadget: at91_udc: Simplify probe and remove functions
usb: gadget: at91_udc: Remove non-DT handling code
usb: gadget: at91_udc: Document DT clocks and clock-names property
usb: gadget: at91_udc: Drop uclk clock
usb: gadget: at91_udc: Fix clock names
mfd: syscon: Add Atmel SMC binding doc
mfd: syscon: Add atmel-smc registers definition
mfd: syscon: Add Atmel Matrix bus DT binding documentation
mfd: syscon: Add atmel-matrix registers definition
clk: shmobile: fix sparse NULL pointer warning
...
Provide a file creation function that also takes an initial size so that the
caller doesn't have to set i_size, thus meaning that we don't have to call
deal with ->d_inode in the callers.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtrcACgkQMUfUDdst+yn0tACgygJPNvu1l3ukNJCCpWuOErIj
3KsAnjiEXv90DLYJiVLJ4EbLPw0V9wAv
=DrJx
-----END PGP SIGNATURE-----
Merge tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (299 commits)
usb: musb: fix device hotplug behind hub
usb: dwc2: Fix a bug in reading the endpoint directions from reg.
staging: emxx_udc: fix the build error
usb: Retry port status check on resume to work around RH bugs
Revert "usb: Reset USB-3 devices on USB-3 link bounce"
uhci-hub: use HUB_CHAR_*
usb: kconfig: replace PPC_OF with PPC
ehci-pci: disable for Intel MID platforms (update)
usb: gadget: Kconfig: use bool instead of boolean
usb: musb: blackfin: remove incorrect __exit_p()
USB: fix use-after-free bug in usb_hcd_unlink_urb()
ehci-pci: disable for Intel MID platforms
usb: host: pci_quirks: joing string literals
USB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)
USB: usbfs: allow URBs to be reaped after disconnection
cdc-acm: kill unnecessary messages
cdc-acm: add sanity checks
usb: phy: phy-generic: Fix USB PHY gpio reset
usb: dwc2: fix USB core dependencies
usb: renesas_usbhs: fix NULL pointer dereference in dma_release_channel()
...
This one was driving me mad, with several lines of warnings during the
allmodconfig build for a single bogus pointer cast. The warning was so
verbose due to the indirect macro expansion explanation, and the whole
thing was just for a debug printout.
The bogus pointer-to-integer cast was pointless anyway, so just remove
it, and use '%p' to show the pointer.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fsl udc core assumes itself always self powered, so set is_selfpowered
is 1.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Robert Baldyga