The octeon-ethernet driver needs to check for additional chip specific
features, we add them to the octeon_has_feature() framework.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The bootloader now uses additional board type constants. The
octeon-ethernet driver needs some of the new values.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The various Octeon ethernet drivers use these new functions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace a few open-coded GPIO register accesses with gpio calls.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace a few GPIO register accesses in the board init code with calls to
the gpio api.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace a few GPIO register accesses in the board init code with calls
to the gpio api.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current in-kernel Alchemy GPIO support is far too inflexible for
all my use cases. To address this, the following changes are made:
* create generic functions which deal with manipulating the on-chip
GPIO1/2 blocks. Such functions are universally useful.
* Macros for GPIO2 shared interrupt management and block control.
* support for both built-in CONFIG_GPIOLIB and fast, inlined GPIO macros.
If CONFIG_GPIOLIB is not enabled, provide linux gpio framework
compatibility by directly inlining the GPIO1/2 functions. GPIO access
is limited to on-chip ones and they can be accessed as documented in
the datasheets (GPIO0-31 and 200-215).
If CONFIG_GPIOLIB is selected, two (2) gpio_chip-s, one for GPIO1 and
one for GPIO2, are registered. GPIOs can still be accessed by using
the numberspace established in the databooks.
However this is not yet flexible enough for my uses: My Alchemy
systems have a documented "external" gpio interface (fixed, different
numberspace) and can support a variety of baseboards, some of which
are equipped with I2C gpio expanders. I want to be able to provide
the default 16 GPIOs of the CPU board numbered as 0..15 and also
support gpio expanders, if present, starting as gpio16.
To achieve this, a new Kconfig symbol for Alchemy is introduced,
CONFIG_ALCHEMY_GPIO_INDIRECT, which boards can enable to signal
that they don't want the Alchemy numberspace exposed to the outside
world, but instead want to provide their own. Boards are now respon-
sible for providing the linux gpio interface glue code (either in a
custom gpio.h header (in board include directory) or with gpio_chips).
To make the board-specific inlined gpio functions work, the MIPS
Makefile must be changed so that the mach-au1x00/gpio.h header is
included _after_ the board headers, by moving the inclusion of
the mach-au1x00/ to the end of the header list.
See arch/mips/include/asm/mach-au1x00/gpio.h for more info.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
gpio_direction_output should also set an output value according to the API.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Rewrite to use <asm-generic/ioctl.h>. Cuts down the file from 40 to
16 lines.
o Delete _IOC_VOID, _IOC_OUT, _IOC_IN and _IOC_INOUT. They were added
for 2.1.14 but I was not able to find any user - not even historical
ones.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a sysdev to access SRAM in TXx9 SoCs via sysfs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CFE is the only supported and used bootloader on the SiByte boards,
the standalone kernel support has been never used outside Broadcom.
Remove it and make the kernel use CFE by default.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes the SiByte simulation Kconfig option, which only modified
a printk.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch makes sure that we are not going to clear
or change the interrupt status of a GPIO interrupt
superior to 13 as this is the maximum number of GPIO
interrupt source (p.232 of the RC32434 reference manual).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CPU_CAVIUM_OCTEON is mips_r2 which is handled before the switch. This
label in the switch statement is dead code, so we remove it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Octeon has no execution hazards, so we can remove them and save an
instruction per TLB handler invocation.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some CPUs do not need ehb instructions after writing CP0 registers.
By allowing ehb generation to be overridden in
cpu-feature-overrides.h, we can save a few instructions in the TLB
handler hot paths.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Try to fold the 64-bit TLB refill handler opportunistically at the
beginning of the vmalloc path so as to avoid splitting execution flow in
half and wasting cycles for a branch required at that point then. Resort
to doing the split if either of the newly created parts would not fit into
its designated slot.
Original-patch-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The logic used to split the r4000 refill handler is liberally
sprinkled with magic numbers. We attempt to explain what they are and
normalize them against a new symbolic value (MIPS64_REFILL_INSNS).
CC: David VomLehn <dvomlehn@cisco.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add platform support for ACLC of TXx9 SoCs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for PCI and PCIe to the base Cavium OCTEON
processor support.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Here we add the register definitions for the processor blocks used by
the following PCI support patch.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the integrated DMAC of the TXx9 family.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use container structure for clocksource, clock_event_device and hold a
pointer to txx9_tmr_reg in it.
This saves a few instructions in clocksource and clock_event handlers.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A wrong resolution of a merge conflict made the recently deleted wrong
error check in sb1250_set_affinity. Send the zombie back to the empire
of the undead.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds initial support for the PCI-Express module in the SH7786,
particularly as it relates to the urquell platform. Presently it is
only supported in root complex mode, with endpoint mode still requiring
more debugging. 29/32-bit mode and lane configurations are selectable via
board mode pins, and are otherwise fixed.
Only 4x and 1x PCI channels are presently handled, the PCI bridge still
requires additional debugging and stabilization in hardware.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables support for the generic software-based perf counters.
Hardware counter support could be added in the future, but the lack
of a performance counter IRQ makes this rather dubious.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch refactors clock.c by replacing printk calls with
pr_info/pr_cont, and uses '=' in output to connect key/value pairs
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Unify i2c camera device platform data to point to struct soc_camera_link
for a smooth transition to soc-camera as a platform driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
and remove redundant parameter for r8a66597-hcd.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
and remove redundant parameter for r8a66597-hcd.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
and remove redundant parameter for r8a66597-hcd.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
and remove redundant parameter for r8a66597-hcd.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
and remove redundant parameter for r8a66597-hcd.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the shared clock cpg code from bootmem to slab.
Without this patch the current bootmem code triggers
WARN_ON() because the slab is available.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix WARN_ON() by modifying the bug trap handling code to
always return in the in-kernel instruction pointer case.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency,
while MPC52xx used mpc52xx_find_ipb_freq(). Despite the different
clock names (IPS vs. IPB) the code was identical.
Use common code for both processor families.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a node for the i2c eeprom and delete the superflous gpio-example.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
Now we have __initconst, we can finally move the external declarations for
the various Linux logo structures to <linux/linux_logo.h>.
James' ack dates back to the previous submission (way to long ago), when the
logos were still __initdata, which caused failures on some platforms with some
toolchain versions.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: James Simmons <jsimmons@infradead.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert most arches to use asm-generic/kmap_types.h.
Move the KM_FENCE_ macro additions into asm-generic/kmap_types.h,
controlled by __WITH_KM_FENCE from each arch's kmap_types.h file.
Would be nice to be able to add custom KM_types per arch, but I don't yet
see a nice, clean way to do that.
Built on x86_64, i386, mips, sparc, alpha(tonyb), powerpc(tonyb), and
68k(tonyb).
Note: avr32 should be able to remove KM_PTE2 (since it's not used) and
then just use the generic kmap_types.h file. Get avr32 maintainer
approval.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Luck Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are some places to be able to use printk_once instead of hard coding.
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
put_cpu_no_resched() is an optimization of put_cpu() which unfortunately
can cause high latencies.
The nfs iostats code uses put_cpu_no_resched() in a code sequence where a
reschedule request caused by an interrupt between the get_cpu() and the
put_cpu_no_resched() can delay the reschedule for at least HZ.
The other users of put_cpu_no_resched() optimize correctly in interrupt
code, but there is no real harm in using the put_cpu() function which is
an alias for preempt_enable(). The extra check of the preemmpt count is
not as critical as the potential source of missing a reschedule.
Debugged in the preempt-rt tree and verified in mainline.
Impact: remove a high latency source
[akpm@linux-foundation.org: build fix]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
`ELF_CORE_COPY_REGS(x, y)' will make expansions like:
`(y)[0] = (x)->x.gp[0]' but correct is `(y)[0] = (x)->regs.gp[0]'
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: WANG Cong <amwang@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When compiling uml on x86_64:
MODPOST vmlinux.o
WARNING: vmlinux.o (.__syscall_stub.2): unexpected non-allocatable section.
Did you forget to use "ax"/"aw" in a .S file?
Note that for example <linux/init.h> contains
section definitions for use in .S files.
Because modpost checks for missing SHF_ALLOC section flag. So just add
it.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have
been kept around for migration reasons. After more than two years it's
time to remove them finally.
This patch cleans up one of the remaining users. When all such patches
hit mainline we can remove the defines and typedefs finally.
Impact: cleanup
Convert the last remaining users to struct irq_chip and remove the
define.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
See ancient discussion at
http://marc.info/?l=user-mode-linux-devel&m=101990155831279&w=2
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=7854
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Roland Kletzing <devzero@web.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have
been kept around for migration reasons. After more than two years it's
time to remove them finally.
This patch cleans up one of the remaining users. When all such patches
hit mainline we can remove the defines and typedefs finally.
Impact: cleanup
Convert the last remaining users to struct irq_chip and remove the
define.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
`for_each_mem_cluster(x, y, z)' will expand to
`for ((x) = (y)->x ...' but correct is `for ((x) = (y)->cluster ...'
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have
been kept around for migration reasons. After more than two years it's
time to remove them finally.
This patch cleans up one of the remaining users. When all such patches
hit mainline we can remove the defines and typedefs finally.
Impact: cleanup
Convert the last remaining users to struct irq_chip and remove the
define.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ALLOC_WMARK_MIN, ALLOC_WMARK_LOW and ALLOC_WMARK_HIGH determin whether
pages_min, pages_low or pages_high is used as the zone watermark when
allocating the pages. Two branches in the allocator hotpath determine
which watermark to use.
This patch uses the flags as an array index into a watermark array that is
indexed with WMARK_* defines accessed via helpers. All call sites that
use zone->pages_* are updated to use the helpers for accessing the values
and the array offsets for setting.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Callers of alloc_pages_node() can optionally specify -1 as a node to mean
"allocate from the current node". However, a number of the callers in
fast paths know for a fact their node is valid. To avoid a comparison and
branch, this patch adds alloc_pages_exact_node() that only checks the nid
with VM_BUG_ON(). Callers that know their node is valid are then
converted.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Paul Mundt <lethal@linux-sh.org> [for the SLOB NUMA bits]
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* create mm/init-mm.c, move init_mm there
* remove INIT_MM, initialize init_mm with C99 initializer
* unexport init_mm on all arches:
init_mm is already unexported on x86.
One strange place is some OMAP driver (drivers/video/omap/) which
won't build modular, but it's already wants get_vm_area() export.
Somebody should look there.
[akpm@linux-foundation.org: add missing #includes]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PIT_TICK_RATE is currently defined in four architectures, but in three
different places. While linux/timex.h is not the perfect place for it, it
is still a reasonable replacement for those drivers that traditionally use
asm/timex.h to get CLOCK_TICK_RATE and expect it to be the PIT frequency.
Note that for Alpha, the actual value changed from 1193182UL to 1193180UL.
This is unlikely to make a difference, and probably can only improve
accuracy. There was a discussion on the correct value of CLOCK_TICK_RATE
a few years ago, after which every existing instance was getting changed
to 1193182. According to the specification, it should be
1193181.818181...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use .code16gcc to compile arch/x86/boot/bioscall.S rather than
.code16, since some older versions of binutils can't generate 32-bit
addressing expressions (67 prefixes) in .code16 mode, only in
.code16gcc mode.
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch causes all the EFI_RESERVED_TYPE memory reservations to be recorded
in the e820 table as type E820_RESERVED.
(This patch replaces one called 'x86: vendor reserved memory type'.
This version has been discussed a bit with Peter and Yinghai but not given
a final opinion.)
Without this patch EFI_RESERVED_TYPE memory reservations may be
marked usable in the e820 table. There may be a collision between
kernel use and some reserver's use of this memory.
(An example use of this functionality is the UV system, which
will access extremely large areas of memory with a memory engine
that allows a user to address beyond the processor's range. Such
areas are reserved in the EFI table by the BIOS.
Some loaders have a restricted number of entries possible in the e820 table,
hence the need to record the reservations in the unrestricted EFI table.)
The call to do_add_efi_memmap() is only made if "add_efi_memmap" is specified
on the kernel command line.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
iomem_resource is by default initialized to -1, which means 64 bits of
physical address space if 64-bit resources are enabled. However, x86
CPUs cannot address 64 bits of physical address space. Thus, we want
to cap the physical address space to what the union of all CPU can
actually address.
Without this patch, we may end up assigning inaccessible values to
uninitialized 64-bit PCI memory resources.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Martin Mares <mj@ucw.cz>
Cc: stable@kernel.org
Rename files that are no longer 64bit specific:
mce_amd_64.c => mce_amd.c
mce_intel_64.c => mce_intel.c
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Now all symbols in the header are static. Remove the header.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
move intel_init_thermal() into therm_throt.c
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Put common functions into therm_throt.c, modify Makefile.
unexpected_thermal_interrupt
intel_thermal_interrupt
smp_thermal_interrupt
intel_set_thermal_handler
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Break smp_thermal_interrupt() into two functions.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Remove unused argument regs from handlers, and use inc_irq_stat.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The mce_disabled on 32bit is a tristate variable [1,0,-1],
while 64bit version is boolean [0,1].
This patch makes mce_disabled always boolean, and use mce_p5_enabled
to indicate the third state instead.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
There are 2 headers:
arch/x86/include/asm/mce.h
arch/x86/kernel/cpu/mcheck/mce.h
and in the latter small header:
#include <asm/mce.h>
This patch move all contents in the latter header into the former,
and fix all files using the latter to include the former instead.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add sysfs interface for admins who want to tweak these options without
rebooting the system.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
"trigger" is not straight forward name for valiable that holds name
of user mode helper program which triggered by machine check events.
This patch renames this valiable and kins to more recognizable names.
trigger => mce_helper
trigger_argv => mce_helper_argv
notify_user => mce_need_notify
No functional changes.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add __read_mostly to data written during setup.
Suggested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Simplify interface of mce_start():
- no_way_out = mce_start(no_way_out, &order);
+ order = mce_start(&no_way_out);
Now Monarch and Subjects share same exit(return) in usual path.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
In mce_cpu_restart, mce_init_timer is called unconditionally.
If !mce_available (e.g. mce is disabled), there are no useful work
for timer. Stop running it.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
If one CPU has no_way_out == 1, all other CPUs should have no_way_out
== 1. But despite global_nwo is read after mce_callin, global_nwo is
updated after mce_callin too. So it is possible that some CPU read
global_nwo before some other CPU update global_nwo, so that no_way_out
== 1 for some CPU, while no_way_out == 0 for some other CPU.
This patch fixes this race condition via moving mce_callin updating
after global_nwo updating, with a smp_wmb in between. A smp_rmb is
added between their reading too.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
This patch introduces the Openmoko GTA02 machine definition.
Much of the code is based on Harald Welte's work, although it
has been largely rewritten several times.
This is intended to be the minimum machine definition to boot and
be able to run a rootfs from NAND on GTA02 / FreeRunner. It does
not bring up the framebuffer / Glamo and lacks many other peripheral
drivers from outside the SoC. But once we have this basis in
mainline kernel, we will be able to introduce the other drivers
and add them here.
Thanks to Sven Rebhan <odinshorse@googlemail.com> for his fixes to this
patch (Kconfig and defconfig files).
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: Fix the GPIO definitions]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch provides initial support for CPU frequency scaling on the
Samsung S3C ARM processors. Currently only S3C6410 processors are
supported, though addition of another data table with supported clock
rates should be sufficient to enable support for further CPUs.
Use the regulator framework to provide optional support for DVFS in
the S3C cpufreq driver. When a software controllable regulator is
configured the driver will use it to lower the supply voltage when
running at a lower frequency, giving improved power savings.
When regulator support is disabled or no regulator can be obtained
for VDDARM the driver will fall back to scaling only the frequency.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This allows the S3C64XX IIS drivers to be converted to the standard
driver model and allows fixes there for problems with attempting to
acquire the clocks for the IIS blocks via the clock API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Issue a warning if _CRS returns too many resource descriptors to be
accommodated by the fixed size resource array instances. If there is no
transparent bridge on the root bus "too many" is the
PCI_BUS_NUM_RESOURCES size of the resource array. Otherwise, the last 3
slots of the resource array must be excluded making the maximum
(PCI_BUS_NUM_RESOURCES - 3).
The current code:
- is silent when _CRS returns too many resource descriptors and
- incorrectly allows use of the last 3 slots of the resource array
for a root bus with a transparent bridge
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Based on PCI Express AER specs, a root port might receive multiple
TLP errors while it could only save a correctable error source id
and an uncorrectable error source id at the same time. In addition,
some root port hardware might be unable to provide a correct source
id, i.e., the source id, or the bus id part of the source id provided
by root port might be equal to 0.
The patchset implements the support in kernel by searching the device
tree under the root port.
Patch 1 changes parameter cb of function pci_walk_bus to return a value.
When cb return non-zero, pci_walk_bus stops more searching on the
device tree.
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently pcm990 camera bus-width management functions request a GPIO and never
free it again. With this approach the GPIO extender driver cannot be unloaded
once camera drivers have been loaded, also unloading theb i2c-pxa bus driver
produces errors, because the GPIO extender driver cannot unregister properly.
Another problem is, that if camera drivers are once loaded before the GPIO
extender driver, the platform code marks the GPIO unavailable and only a reboot
helps to recover. Adding an explicit free_bus method and using it in mt9m001
and mt9v022 drivers fixes these problems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ia64 doesn't have old and new versions of the umount system call.
It just has the new version.
Fixes this build warning:
<stdin>:395:2: warning: #warning syscall umount2 not implemented
Signed-off-by: Tony Luck <tony.luck@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (64 commits)
debugfs: use specified mode to possibly mark files read/write only
debugfs: Fix terminology inconsistency of dir name to mount debugfs filesystem.
xen: remove driver_data direct access of struct device from more drivers
usb: gadget: at91_udc: remove driver_data direct access of struct device
uml: remove driver_data direct access of struct device
block/ps3: remove driver_data direct access of struct device
s390: remove driver_data direct access of struct device
parport: remove driver_data direct access of struct device
parisc: remove driver_data direct access of struct device
of_serial: remove driver_data direct access of struct device
mips: remove driver_data direct access of struct device
ipmi: remove driver_data direct access of struct device
infiniband: ehca: remove driver_data direct access of struct device
ibmvscsi: gadget: at91_udc: remove driver_data direct access of struct device
hvcs: remove driver_data direct access of struct device
xen block: remove driver_data direct access of struct device
thermal: remove driver_data direct access of struct device
scsi: remove driver_data direct access of struct device
pcmcia: remove driver_data direct access of struct device
PCIE: remove driver_data direct access of struct device
...
Manually fix up trivial conflicts due to different direct driver_data
direct access fixups in drivers/block/{ps3disk.c,ps3vram.c}
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6: (30 commits)
sparc64: Update defconfig.
sparc: Wire up sys_rt_tgsigqueueinfo().
openprom: Squelch useless GCC warning.
sparc: replace uses of CPU_MASK_ALL_PTR
sparc64: Add proper dynamic ftrace support.
sparc: Simplify code using is_power_of_2() routine.
sparc: move of_device common code to of_device_common
sparc: remove dma-mapping_{32|64}.h
sparc: use dma_map_page instead of dma_map_single
sparc: add sync_single_for_device and sync_sg_for_device to struct dma_ops
sparc: move the duplication in dma-mapping_{32|64}.h to dma-mapping.h
p9100: use standard fields for framebuffer physical address and length
leo: use standard fields for framebuffer physical address and length
cg6: use standard fields for framebuffer physical address and length
cg3: use standard fields for framebuffer physical address and length
cg14: use standard fields for framebuffer physical address and length
bw2: use standard fields for framebuffer physical address and length
sparc64: fix and optimize irq distribution
sparc64: Use new dynamic per-cpu allocator.
sparc64: Only allocate per-cpu areas for possible cpus.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (27 commits)
Blackfin: hook up new rt_tgsigqueueinfo syscall
Blackfin: improve CLKIN_HZ config default
Blackfin: initial support for ftrace grapher
Blackfin: initial support for ftrace
Blackfin: enable support for LOCKDEP
Blackfin: add preliminary support for STACKTRACE
Blackfin: move custom sections into sections.h
Blackfin: punt unused/wrong mutex-dec.h
Blackfin: add support for irqflags
Blackfin: add support for bzip2/lzma compressed kernel images
Blackfin: convert Kconfig style to def_bool
Blackfin: bf548-ezkit: update smsc911x resources
Blackfin: update aedos-ipipe code to upstream 1.10-00
Blackfin: bf537-stamp: update ADP5520 resources
Blackfin: bf518f-ezbrd: fix SPI CS for SPI flash
Blackfin: define SPI IRQ in board resources
Blackfin: do not configure the UART early if on wrong processor
Blackfin: fix deadlock in SMP IPI handler
Blackfin: fix flag storage for irq funcs
Blackfin: push down exception oops checking
...
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (38 commits)
ps3flash: Always read chunks of 256 KiB, and cache them
ps3flash: Cache the last accessed FLASH chunk
ps3: Replace direct file operations by callback
ps3: Switch ps3_os_area_[gs]et_rtc_diff to EXPORT_SYMBOL_GPL()
ps3: Correct debug message in dma_ioc0_map_pages()
drivers/ps3: Add missing annotations
ps3fb: Use ps3_system_bus_[gs]et_drvdata() instead of direct access
ps3flash: Use ps3_system_bus_[gs]et_drvdata() instead of direct access
ps3: shorten ps3_system_bus_[gs]et_driver_data to ps3_system_bus_[gs]et_drvdata
ps3: Use dev_[gs]et_drvdata() instead of direct access for system bus devices
block/ps3: remove driver_data direct access of struct device
ps3vram: Make ps3vram_priv.reports a void *
ps3vram: Remove no longer used ps3vram_priv.ddr_base
ps3vram: Replace mutex by spinlock + bio_list
block: Add bio_list_peek()
powerpc: Use generic atomic64_t implementation on 32-bit processors
lib: Provide generic atomic64_t implementation
powerpc: Add compiler memory barrier to mtmsr macro
powerpc/iseries: Mark signal_vsp_instruction() as maybe unused
powerpc/iseries: Fix unused function warning in iSeries DT code
...
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
therm_windtunnel: Convert to a new-style i2c driver
therm_adt746x: Convert to a new-style i2c driver
windfarm: Convert to new-style i2c drivers
therm_pm72: Convert to a new-style i2c driver
i2c-viapro: Add new PCI device ID for VX855
i2c/chips: Move max6875 to drivers/misc/eeprom
i2c: Do not give adapters a default parent
i2c: Do not probe for TV chips on Voodoo3 adapters
i2c: Retry automatically on arbitration loss
i2c: Remove void casts
The wm8731 driver has been converted to register using the standard I2C
device registration mechanism so we can now do the registration in the
arch/arm code as normal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Maxim 1586 V3 gain can be configured by external resistors
(R24, R25) connected to the FB3 pin. To avoid accidental
overvoltage, it now requires this gain to be configured
explicitly.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
On this board, the PXA272 CPU voltage VCC_CORE is provided
by a Maxim 1586 voltage regulator. Use the regulator
framework to provide VCC_CORE control. When cpufreq will be
updated to ask for vcc_core, this will optimize power
drained by the board.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
On this board, the PXA270 CPU voltage VCC_CORE is provided
by a Maxim 1587A voltage regulator configured to provide
1.55 V maximum voltage for 624 MHz operation.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
After commit 6b849bcff0 (ASoC: Convert PXA
AC97 driver to probe with the platform device) AC97 controller device
should be registered explicitly for both ASoC and generic AC97 drivers
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Register userspace-consumer devices to allow userspace control of
voltage regulators supplying GPS and GPRS modules
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
CPU_MASK_ALL is the (deprecated) "all bits set" cpumask, defined as so:
#define CPU_MASK_ALL (cpumask_t) { { ... } }
Taking the address of such a temporary is questionable at best,
unfortunately 321a8e9d (cpumask: add CPU_MASK_ALL_PTR macro) added
CPU_MASK_ALL_PTR:
#define CPU_MASK_ALL_PTR (&CPU_MASK_ALL)
Which formalizes this practice. One day gcc could bite us over this
usage (though we seem to have gotten away with it so far).
[Description by Rusty Russell]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves code common to of_device_32.c and of_device_64.c into
of_device_common.h and of_device_common.c.
The only functional difference is in sparc32 where of_bus_default_map is
used in place of of_bus_sbus_map because they are equivelent.
There is still room for further code consolidation with some minor
refactoring.
Boot tested on sparc32 and compile tested on sparc64.
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This modifies SPARC32 to use struct dma_map ops. It means that we can
remove dma-mapping_{32|64}.h.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts dma_map_single and dma_unmap_single to use
map_page and unmap_page respectively and removes unnecessary
map_single and unmap_single. map_page can be used to implement
map_single but the opposite is impossible. Having only dma_map_page in
struct dma_ops is enough.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds sync_single_for_device() and sync_sg_for_device() to struct
dma_ops in order to unify dma-mpping_{32|64}.h. dma-mpping_32.h needs them though dma-mpping_64.h doesn't.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
irq_choose_cpu() should compare the affinity mask against cpu_online_map
rather than CPU_MASK_ALL, since irq_select_affinity() sets the interrupt's
affinity mask to cpu_online_map "and" CPU_MASK_ALL (which ends up being
just cpu_online_map). The mask comparison in irq_choose_cpu() will always
fail since the two masks are not the same. So the CPU chosen is the first CPU
in the intersection of cpu_online_map and CPU_MASK_ALL, which is always CPU0.
That means all interrupts are reassigned to CPU0...
Distributing interrupts to CPUs in a linearly increasing round robin fashion
is not optimal for the UltraSPARC T1/T2. Also, the irq_rover in
irq_choose_cpu() causes an interrupt to be assigned to a different
processor each time the interrupt is allocated and released. This may lead
to an unbalanced distribution over time.
A static mapping of interrupts to processors is done to optimize and balance
interrupt distribution. For the T1/T2, interrupts are spread to different
cores first, and then to strands within a core.
The following is some benchmarks showing the effects of interrupt
distribution on a T2. The test was done with iperf using a pair of T5220
boxes, each with a 10GBe NIU (XAUI) connected back to back.
TCP | Stock Linear RR IRQ Optimized IRQ
Streams | 2.6.30-rc5 Distribution Distribution
| GBits/sec GBits/sec GBits/sec
--------+-----------------------------------------
1 0.839 0.862 0.868
8 1.16 4.96 5.88
16 1.15 6.40 8.04
100 1.09 7.28 8.68
Signed-off-by: Hong H. Pham <hong.pham@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This gets us real close to the generic implementation of
setup_per_cpu_areas() except:
1) We store the per-cpu offset into the trap_block[], whereas
the generic code has it's own static array.
2) We have to initialize the %g5 register to hold the boot cpu's
per-cpu area offset.
3) The OBP/MDESC cpu info scan is performed at the end.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we defer the cpu_data() initializations to the end of per-cpu
setup, we can get rid of this local hack we had to setup the per-cpu
areas eary.
This is a necessary step in order to support HAVE_DYNAMIC_PER_CPU_AREA
since the per-cpu setup must run when page structs are available.
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to split up the cpu present mask setup from the cpu_data
initialization, and this is a first step towards that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Later we're going to want to get at these definitions from
asm/percpu.h and that's not possible via cpudata.h because
of the set of dependencies the non-trap_block[] stuff has.
Signed-off-by: David S. Miller <davem@davemloft.net>
This really isn't necessary at all, a local variable suits the
job just fine.
This frees up 8 bytes in the trap_block[] that we can use later
to store the per-cpu base addresses.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the hibernation backend support to the
s390 architecture. Now it is possible to suspend a mainframe Linux
guest using the following command:
echo disk > /sys/power/state
Signed-off-by: Hans-Joachim Picht <hans@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If something goes wrong in a suspend / resume cycle a ccw based console
if very likely in the suspended state and cannot print anything.
Introduce ccw_device_force_console to force the wake up of the console
device to be able to print the oops message. The console device drivers
should use this function only if the system paniced.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the following build failure caused by make allyesconfig using
CONFIG_HIBERNATION and CONFIG_DEBUG_PAGEALLOC
kernel/built-in.o: In function `saveable_page':
kernel/power/snapshot.c:897: undefined reference to `kernel_page_present'
kernel/built-in.o: In function `safe_copy_page':
kernel/power/snapshot.c:948: undefined reference to `kernel_page_present'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Hans-Joachim Picht <hans@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Prefetch instructions can generate spurious faults on certain
models of older CPUs. The faults themselves cannot be stopped
and they can occur pretty much anywhere - so the way we solve
them is that we detect certain patterns and ignore the fault.
There is one small path of code where we must not take faults
though: the #PF handler execution leading up to the reading
of the CR2 (the faulting address). If we take a fault there
then we destroy the CR2 value (with that of the prefetching
instruction's) and possibly mishandle user-space or
kernel-space pagefaults.
It turns out that in current upstream we do exactly that:
prefetchw(&mm->mmap_sem);
/* Get the faulting address: */
address = read_cr2();
This is not good.
So turn around the order: first read the cr2 then prefetch
the lock address. Reading cr2 is plenty fast (2 cycles) so
delaying the prefetch by this amount shouldnt be a big issue
performance-wise.
[ And this might explain a mystery fault.c warning that sometimes
occurs on one an old AMD/Semptron based test-system i have -
which does have such prefetch problems. ]
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
LKML-Reference: <20090616030522.GA22162@Krystal>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that enable_iommus() will call iommu_disable() for each iommu,
the call to disable_iommus() during resume is redundant. Also, the order
for an invalidation is to invalidate device table entries first, then
domain translations.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Clock function was changed, but highlander used old function.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Driver support for the new high-speed/OtG block that is
in the newer line of Samsung SoC devices such as the
S3C64XX series.
This driver does not currntly have DMA support enabled due
to issues with buffer alignment which need to be sorted out.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: linux-mips@linux-mips.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support to the x86 cpuid and msr drivers to report the proper
device name to userspace for their devices.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for misc devices to report their requested nodename to
userspace. It also updates a number of misc drivers to provide the
needed subdirectory and device name to be used for them.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without this clobber, mtspr can be re-ordered by gcc vs. surrounding
memory accesses. While this might be ok for some cases, it's not in
others and I'm not confident that all callers get it right (In fact
I'm sure some of them don't).
So for now, let's make mtspr() itself contain a memory clobber until
we can audit and fix everything, at which point we can remove it
if we think it's worth doing so.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit 5b7c3c918c introduced an invalid
construct in our CPU selection. This caused warnings, though it still
appeared to do the right thing.
This fixes it properly by having separate formal definitions of
PPC_BOOK3S_32 and PPC_BOOK3S_64 and one statement defining
PPC_BOOK3S based on the two above.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add the option to build the code under arch/powerpc with -Werror.
The intention is to make it harder for people to inadvertantly introduce
warnings in the arch/powerpc code. It needs to be configurable so that
if a warning is introduced, people can easily work around it while it's
being fixed.
The option is a negative, ie. don't enable -Werror, so that it will be
turned on for allyes and allmodconfig builds.
The default is n, in the hope that developers will build with -Werror,
that will probably lead to some build breaks, I am prepared to be flamed.
It's not enabled for math-emu, which is a steaming pile of warnings.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The macro spin_event_timeout() takes a condition and timeout value
(in microseconds) as parameters. It spins until either the condition is true
or the timeout expires. It returns the result of the condition when the loop
was terminated.
This primary purpose of this macro is to poll on a hardware register until a
status bit changes. The timeout ensures that the loop still terminates if the
bit doesn't change as expected. This macro makes it easier for driver
developers to perform this kind of operation properly.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If no device is passed to __dma_alloc_coherent, it defaults to using ISA_DMA_THRESHOLD
for the mask. This patch provides a reasonable default rather than 0.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some XPedite52xx boards have a legacy boot loader requiring some special
care in the boot wrapper. The use of cuboot-85xx is needed to fix
up embedded device trees, and a custom link address is specified to
accommodate the boot loader and larger kernel image sizes used on X-ES
MPC85xx platforms.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add device tree source files for various MPC85xx boards from Extreme
Engineering Solutions. Supported boards include XPedite5370,
XPedite5200, XPedite5301, XPedite5330, and XCalibur1501.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for X-ES single-board computers based on the Freescale
MPC85xx processors.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following series implements basic board support for
the kmeter1 board from keymile, based on a MPC8360.
This series provides the following functionality:
- The board can boot with a serial console on UART1
- Ethernet:
UCC1 in RGMII mode
UCC2 in RGMII mode
UCC4 in RMII mode
UCC5 in RMII mode
UCC6 in RMII mode
UCC7 in RMII mode
UCC8 in RMII mode
following patch is necessary for working UCC in RMII mode:
http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/070804.html
- Flash accessed via MTD layer
On this hardware there is an Intel P30 flash, following patch
series is necessary for working with this hardware:
http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/070624.html
- I2C using I2C Bus 1 from the MPC8360 cpu
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add 4 partitions in nor flash. Also fix nor flash bank width bug. The
flash is capable of x8/x16 width but is configured for x8.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently the fsl,*lbc devices support 8 banks (ie OR and BR registers).
This is adequate for most pq2 and pq3 processors, but not the MPC8280 which
has 12 banks.
Signed-Off-By: Mark Ware <mware@elphinstone.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some MPC85xx platforms do support 4 ethernet ports, so make sure the boot
wrapper fixes up all of them in the fdt.
Since MAC addresses are at the end of the bd_t structure there is no harm
in expanding to support 4 MAC address on older 85xx systems that might not
have that many.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently the kernel expects the additional four IBAT and DBAT registers
to be available, but doesn't enable these registers on 745x CPUs, which
have them disabled after reset. Thus set the HIGH_BAT_EN bit in HID0
register, if the corresponding MMU feature is defined.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
usb0 and usb1 mux settings in the sicrl register were swapped (twice!)
in mpc834x_usb_cfg(), leading to various strange issues with fsl-ehci
and full speed devices.
The USB port config on mpc834x is done using 2 muxes: Port 0 is always
used for MPH port 0, and port 1 can either be used for MPH port 1 or DR
(unless DR uses UTMI phy or OTG, then it uses both ports) - See 8349 RM
figure 1-4..
mpc8349_usb_cfg() had this inverted for the DR, and it also had the bit
positions of the usb0 / usb1 mux settings swapped. It would basically
work if you specified port1 instead of port0 for the MPH controller (and
happened to use ULPI phys), which is what all the 834x dts have done,
even though that configuration is physically invalid.
Instead fix mpc8349_usb_cfg() and adjust the dts files to match reality.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCIe MSI interrupts are missing from the device tree source, and
thus were not enabled. This patch adds them.
Tested to work on MPC8315E-RDB with custom FPGA PCIe device.
Signed-off-by: Leon Woestenberg <leon@sidebranch.com>
Tested-by: Leon Woestenberg <leon@sidebranch.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mappings for temperature sensors (adt7461 and lm92) are missing from the
SBC610's DTS file.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As of commit 404614728f ("Update FSL
esdhc binding"), we use "fsl,esdhc" compatible entry as a base
match. U-Boot will use the same compatible to fixup esdhc nodes.
This patch updates 83xx dts files so that they conform to the new
bindings.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some boot loaders may not enable L1 instruction/data cache. Check if
data and instruction caches are enabled, and enable them if needed.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current device tree for the MPC8272ADS assumes a mapping of 32 MB
of NOR flash at 0xFE00.0000, while there are actually only 8 MB on
the boards, mapped at 0xFF80.0000. When booting an uImage with such a
device tree, the kernel crashes because 0xFE00.0000 is not mapped.
Also introduce aliases for serial[01] and ethernet[01].
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the platform-specific code for enabling SWIOTLB if needed on P2020DS,
MPC85xx DS, and MPC85xx MDS boards as they are capable of having >4G of
memory.
We determine if we need to enable swiotlb based on how much memory is in
the board and if it exceeds 4G or what we can map via PCI inbound
windows.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is the final bit of code to allow enabling swiotlb on
mpc86xx. The platform-specific code is very small and consists
of enabling SWIOTLB in the config file, registering the
swiotlb_setup_bus_notifier initcall, and setting pci_dma_ops
to point to swiotlb_pci_dma_ops if we have more memory than
can be mapped by the inbound PCI windows.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have
been kept around for migration reasons. After more than two years it's
time to remove them finally.
This patch cleans up one of the remaining users. When all such patches
hit mainline we can remove the defines and typedefs finally.
Impact: cleanup
Convert the last remaining users to struct irq_chip and remove the
define.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have
been kept around for migration reasons. After more than two years it's
time to remove them finally.
This patch cleans up one of the remaining users. When all such patches
hit mainline we can remove the defines and typedefs finally.
Impact: cleanup
Convert the last remaining users and remove the typedef.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have
been kept around for migration reasons. After more than two years it's
time to remove them finally.
This patch cleans up one of the remaining users. When all such patches
hit mainline we can remove the defines and typedefs finally.
Impact: cleanup
convert the last remaining users to no_irq_chip
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
fpswa.h is not relevant for userspace,
so do not export it.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This adds in preliminary support for the SH7786 PCIe module PCI ops,
and the corresponding module definitions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Just a working, starting point config file for the board.
Signed-off-by: Michel Pollet <buserror@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The MINI2440 is a chinese made s3c2440 development board with
a large set of peripherals.
This patch provides machine support for almost all the features
of the board.
Since it can come with various "options" fitted, a kernel parameter
is used to specify the lcd size, backlight control and touchscreen.
Signed-off-by: Michel Pollet <buserror@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Some host controllers (such as SH7786) have overlapping regions that are
fixed in hardware. The resource allocator does the right thing in
managing this space already, so the conflict case is non-fatal.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the LAN9118 ethernet on rsk7203.
The LAN9118 controller is hooked up using a 16-bit data bus,
but the rsk7203 board does not swap the byte lanes as needed
between the sh7203 processor and the the ethernet controller.
In the processor the CS memory window is configured in 16-bit
mode but the smsc911x driver is told to do 32-bit accesses to
improve performance. The SMSC911X_SWAP_FIFO flag is used
to tell the driver to do software byte swapping of fifo data.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'timers-for-linus-migration' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: Logic to move non pinned timers
timers: /proc/sys sysctl hook to enable timer migration
timers: Identifying the existing pinned timers
timers: Framework for identifying pinned timers
timers: allow deferrable timers for intervals tv2-tv5 to be deferred
Fix up conflicts in kernel/sched.c and kernel/timer.c manually
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (103 commits)
powerpc: Fix bug in move of altivec code to vector.S
powerpc: Add support for swiotlb on 32-bit
powerpc/spufs: Remove unused error path
powerpc: Fix warning when printing a resource_size_t
powerpc/xmon: Remove unused variable in xmon.c
powerpc/pseries: Fix warnings when printing resource_size_t
powerpc: Shield code specific to 64-bit server processors
powerpc: Separate PACA fields for server CPUs
powerpc: Split exception handling out of head_64.S
powerpc: Introduce CONFIG_PPC_BOOK3S
powerpc: Move VMX and VSX asm code to vector.S
powerpc: Set init_bootmem_done on NUMA platforms as well
powerpc/mm: Fix a AB->BA deadlock scenario with nohash MMU context lock
powerpc/mm: Fix some SMP issues with MMU context handling
powerpc: Add PTRACE_SINGLEBLOCK support
fbdev: Add PLB support and cleanup DCR in xilinxfb driver.
powerpc/virtex: Add ml510 reference design device tree
powerpc/virtex: Add Xilinx ML510 reference design support
powerpc/virtex: refactor intc driver and add support for i8259 cascading
powerpc/virtex: Add support for Xilinx PCI host bridge
...
ad6561dffa ("module: trim exception table on init
free.") put a bogus trim_init_extable() function into ia64 which didn't compile.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This driver only reads the user EEPROM of that chip, so we can move it
to the eeprom-directory in order to further clean up (and later remove)
drivers/i2c/chips.
The Kconfig text was updated to match the current functionality,
dropping the meanwhile obsoleted parts.
Defconfigs have been adapted.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove all old-style cpumask operators, and cpumask_t.
Also: get rid of the unused define_siblings function.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Mark Langsdorf <mark.langsdorf@amd.com>
Tested-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
cpumask: avoid playing with cpus_allowed in powernow-k8.c
It's generally a very bad idea to mug some process's cpumask: it could
legitimately and reasonably be changed by root, which could break us
(if done before our code) or them (if we restore the wrong value).
I did not replace powernowk8_target; it needs fixing, but it grabs a
mutex (so no smp_call_function_single here) but Mark points out it can
be called multiple times per second, so work_on_cpu is too heavy.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
To: cpufreq@vger.kernel.org
Acked-by: Mark Langsdorf <mark.langsdorf@amd.com>
Tested-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Impact: don't play with current's cpumask
It's generally a very bad idea to mug some process's cpumask: it could
legitimately and reasonably be changed by root, which could break us
(if done before our code) or them (if we restore the wrong value).
Use rdmsr_on_cpu and wrmsr_on_cpu instead.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
To: cpufreq@vger.kernel.org
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Impact: don't play with current's cpumask
It's generally a very bad idea to mug some process's cpumask: it could
legitimately and reasonably be changed by root, which could break us
(if done before our code) or them (if we restore the wrong value).
We use smp_call_function_single: this had the advantage of being more
efficient, too.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
To: cpufreq@vger.kernel.org
Cc: Dominik Brodowski <linux@brodo.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Make powernowk8_get() similar to powernowk8_target() and powernowk8_verify()
in the way it obtains "powernow_data" for a given CPU.
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Langsdorf, Mark <mark.langsdorf@amd.com>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Tested-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Langsdorf, Mark <mark.langsdorf@amd.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
By definition, "cpuinfo_cur_freq" should report the value from HW. So, don't
depend on the cached value. Instead read P-state directly from HW, while
taking into account the erratum 311 workaround for Fam 11h processors.
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Langsdorf, Mark <mark.langsdorf@amd.com>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Tested-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Langsdorf, Mark <mark.langsdorf@amd.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
This symbol doesn't need file-global scope.
Cc: "Zhang, Rui" <rui.zhang@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Langsdorf, Mark <mark.langsdorf@amd.com>
Cc: Leo Milano <lmilano@gmx.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Christoph Hellwig noticed the following potential uninitialised use:
> arch/x86/kernel/tsc.c: In function 'time_cpufreq_notifier':
> arch/x86/kernel/tsc.c:634: warning: 'dummy' may be used uninitialized in this function
>
> where we do have CONFIG_SMP set, freq->flags & CPUFREQ_CONST_LOOPS is
> true and ref_freq is false.
It seems plausable, though the circumstances for hitting it are really low.
Nearly all SMP capable cpufreq drivers set CPUFREQ_CONST_LOOPS.
powernow-k8 is really the only exception. The older CPUs were typically
only ever UP. (powernow-k7 never supported SMP for eg)
It's worth fixing regardless, as it cleans up the code.
Fix possible uninitialized use of dummy, by just removing it,
and making the setting of lpj more obvious.
Signed-off-by: Dave Jones <davej@redhat.com>
This doesn't fix anything, but it's expected that a transition latency of 0
could cause trouble in the future.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Cc: Langsdorf, Mark <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
I just realized this has a kmap_atomic bug in...
The below would fix it - but it's complicating this code
some more.
Alternatively I would have to introduce something like
pte_offset_map_irq() which would make the irq/nmi detection and leave
the regular code paths alone, however that would mean either duplicating
the gup_fast() pagewalk or passing down a pte function pointer, which
would only duplicate the gup_pte_range() bit, neither is really
attractive ...
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Nick Piggin <npiggin@suse.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
At present, every architecture that supports perf_counters has to
declare set_perf_counter_pending() in its arch-specific headers.
This consolidates the declarations into a single declaration in one
common place, include/linux/perf_counter.h. On powerpc, we continue
to provide a static inline definition of set_perf_counter_pending()
in the powerpc hw_irq.h.
Also, this removes from the x86 perf_counter.h the unused null
definitions of {test,clear}_perf_counter_pending.
Reported-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: benh@kernel.crashing.org
LKML-Reference: <18998.13388.920691.523227@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes a couple of compile warnings that crept into the powerpc
perf_counter code recently:
CC arch/powerpc/kernel/perf_counter.o
arch/powerpc/kernel/perf_counter.c: In function 'record_and_restart':
arch/powerpc/kernel/perf_counter.c:1016: warning: unused variable 'addr'
arch/powerpc/kernel/perf_counter.c: In function 'hw_perf_counter_init':
arch/powerpc/kernel/perf_counter.c:891: warning: 'ev' may be used uninitialized in this function
Stephen Rothwell reported this against linux-next as well.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <18998.12884.787039.22202@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
These registers may contain values from previous kernels. So reset them
to known values before enable the event buffer again.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
__copy_from_user_inatomic() isn't NMI safe in that it can trigger
the page fault handler which is another trap and its return path
invokes IRET which will also close the NMI context.
Therefore use a GUP based approach to copy the stack frames over.
We tried an alternative solution as well: we used a forward ported
version of Mathieu Desnoyers's "NMI safe INT3 and Page Fault" patch
that modifies the exception return path to use an open-coded IRET with
explicit stack unrolling and TF checking.
This didnt work as it interacted with faulting user-space instructions,
causing them not to restart properly, which corrupts user-space
registers.
Solving that would probably involve disassembling those instructions
and backtracing the RIP. But even without that, the code was deemed
rather complex to the already non-trivial x86 entry assembly code,
so instead we went for this GUP based method that does a
software-walk of the pagetables.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Two new kmap_atomic slots for NMI context. And teach pte_offset_map()
about NMI context.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Nick Piggin <npiggin@suse.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce a gup_fast() variant which is usable from IRQ/NMI context.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Nick Piggin <npiggin@suse.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The IOMMU spec states that IOMMU behavior may be undefined when the
IOMMU registers are rewritten while command or event buffer is enabled.
Disable them in IOMMU disable path.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
We've had some troubles in the past with weird instructions. This
patch adds a self-test framework which can be used to verify that
a certain set of opcodes are decoded correctly. Of course, the
opcodes which are not tested can still give the wrong results.
In short, this is just a safeguard to catch unintentional changes
in the opcode decoder. It does not mean that errors can't still
occur!
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Only _PAGE_HIDDEN when CONFIG_KMEMCHECK is defined, otherwise set it
to 0. Allows later cleanups.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
The Kconfig options of kmemcheck are hidden under arch/x86 which makes porting
to other architectures harder. To fix that, move the Kconfig bits to
lib/Kconfig.kmemcheck and introduce a CONFIG_HAVE_ARCH_KMEMCHECK config option
that architectures can define.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
let it rip!
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegardno@ifi.uio.no>
This adds support for tracking the initializedness of memory that
was allocated with the page allocator. Highmem requests are not
tracked.
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
[build fix for !CONFIG_KMEMCHECK]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
When kexec'ing to a new kernel (for example, when crashing and launching
a kdump session), the AMD IOMMU may have cached translations. The kexec'd
kernel, during initialization, will invalidate the IOMMU device table
entries, but not the domain translations. These stale entries can cause
a device's DMA to fail, makes it rough to write a dump to disk when the
disk controller can't DMA ;-)
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
If the IOMMUs are still enabled when the kexec kernel boots access to
the disk is not possible. This is bad for tools like kdump or anything
else which wants to use PCI devices.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
When the IOMMU stays enabled the BIOS may not be able to finish the
machine shutdown properly. So disable the hardware on shutdown.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This is needed for page allocator support to prevent false positives
when accessing pages which are dma-mapped.
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
As these are allocated using the page allocator, we need to pass
__GFP_NOTRACK before we add page allocator support to kmemcheck.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
This patch hooks into the DMA API to prevent the reporting of the
false positives that would otherwise be reported when memory is
accessed that is also used directly by devices.
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
With kmemcheck enabled, the slab allocator needs to do this:
1. Tell kmemcheck to allocate the shadow memory which stores the status of
each byte in the allocation proper, e.g. whether it is initialized or
uninitialized.
2. Tell kmemcheck which parts of memory that should be marked uninitialized.
There are actually a few more states, such as "not yet allocated" and
"recently freed".
If a slab cache is set up using the SLAB_NOTRACK flag, it will never return
memory that can take page faults because of kmemcheck.
If a slab cache is NOT set up using the SLAB_NOTRACK flag, callers can still
request memory with the __GFP_NOTRACK flag. This does not prevent the page
faults from occuring, however, but marks the object in question as being
initialized so that no warnings will ever be produced for this object.
In addition to (and in contrast to) __GFP_NOTRACK, the
__GFP_NOTRACK_FALSE_POSITIVE flag indicates that the allocation should
not be tracked _because_ it would produce a false positive. Their values
are identical, but need not be so in the future (for example, we could now
enable/disable false positives with a config option).
Parts of this patch were contributed by Pekka Enberg but merged for
atomicity.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
The hooks that we modify are:
- Page fault handler (to handle kmemcheck faults)
- Debug exception handler (to hide pages after single-stepping
the instruction that caused the page fault)
Also redefine memset() to use the optimized version if kmemcheck is
enabled.
(Thanks to Pekka Enberg for minimizing the impact on the page fault
handler.)
As kmemcheck doesn't handle MMX/SSE instructions (yet), we also disable
the optimized xor code, and rely instead on the generic C implementation
in order to avoid false-positive warnings.
Signed-off-by: Vegard Nossum <vegardno@ifi.uio.no>
[whitespace fixlet]
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegardno@ifi.uio.no>
Lets use kmemcheck_pte_lookup() in kmemcheck_fault() instead of
open-coding it there.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
This patch moves the CONFIG_X86_64 ifdef out of kmemcheck_opcode_decode() by
introducing a version of the function that always returns false for
CONFIG_X86_32.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Multiple ifdef'd definitions of the same global variable is ugly and
error-prone. Fix that up.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
The "Bugs, beware!" printout during is cute but confuses users that something
bad happened so change the text to the more boring "Initialized" message.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
This patch reorders code in error.c so that we can get rid of the forward
declarations.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Urquell has a system FPGA capable of reading the mode pin states from
software, wire this up in the machvec.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Kernel-space call-chains were trimmed at the first entry because
we never processed anything beyond the first stack context.
Allow the backtrace to jump from NMI to IRQ stack then to task stack
and finally user-space stack.
Also calculate the stack and bp variables correctly so that the
stack walker does not exit early.
We can get deep traces as a result, visible in perf report -D output:
0x32af0 [0xe0]: PERF_EVENT (IP, 5): 15134: 0xffffffff815225fd period: 1
... chain: u:2, k:22, nr:24
..... 0: 0xffffffff815225fd
..... 1: 0xffffffff810ac51c
..... 2: 0xffffffff81018e29
..... 3: 0xffffffff81523939
..... 4: 0xffffffff81524b8f
..... 5: 0xffffffff81524bd9
..... 6: 0xffffffff8105e498
..... 7: 0xffffffff8152315a
..... 8: 0xffffffff81522c3a
..... 9: 0xffffffff810d9b74
..... 10: 0xffffffff810dbeec
..... 11: 0xffffffff810dc3fb
This is a 22-entries kernel-space chain.
(We still only record reliable stack entries.)
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the FLASH database is updated by the kernel using file operations,
meant for userspace only. While this works for us because copy_{from,to}_user()
on powerpc can handle kernel pointers, this is unportable and a bad example.
Replace the file operations by callbacks, registered by the ps3flash driver.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
They were never intended to be exported using EXPORT_SYMBOL() anyway
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It reports the failure of a call to lv1_put_iopte(), not
lv1_map_device_dma_region().
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
David Daney