- add "async" gpn_ft, gnn_ft, gfpn_id, gnn_id switch commands.
- For 8G and newer adapters, use async commands when it comes to
fabric scan to reduce bottle neck.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When connection type is N_Port to N_Port (point-to-point), there
is a possibilty where initiator will not send PLOGI request and
will directly send PRLI. In N2N connection the port has higher
port name sends the PLOGI but not allow to send PRLI if is a
target mode. Only initiator is allowed to send PRLI.
Current driver code deletes old session when it receives PLOGI
request. If we will not receive PLOGI request then we will not
delete old session and create new session. Add check for N2N
with PRLI receive only and trigger cleanup. For this case, the
cleanup requires individual cmd abort instead of using implicit
logout as a broad stroke flush.
Signed-off-by: Krishna Kant <krishna.kant@purestorage.com>
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For Dual Mode, Initiator side of the driver finish login,
target side receive PRLI, but driver terminates PRLI.
This patch allows target side to go ahead and accept PRLI.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The logo ELS command allocates dma coherent memory for the
data payload and serialize the completions. When this command
times out, the timeout routine completes the thread waiting
for completion which in turn cleanup resources allocated for
this ELS command processing. Don't call generic sp->free
routine when this ELS command times out to avoid to double
freeing of the same resources.
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add ability to send Implicit PRLO to flush IOs
from FW back to driver.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add option to tell FW to reserve 1/2 of emergency exchanges for ELS.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
DPC thread can stall during switch scan due to slow switch response.
This will stall other work element that needs attention. Moving work
element processing and relogin logic out of DPC thread and into its
own work queue.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace call to Get Port DataBase MB with PDO_FORCE_ADISC
flag with async ADISC command so driver can see ADISC command
has error or not.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adjusts and reallocates fw_dump memory for target mode
to save for extended login and exchange offload buffers into
dump captured.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use IOCB patch to submit Control VP MBX command to reduce
bottle-neck for mbx interface.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
when processing iocb in a timeout case, driver was trying to log messages
without verifying if the fcport structure could have valid data. This
results in a NULL pointer access.
Fixes: 726b85487067("qla2xxx: Add framework for async fabric discovery")
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driver is loaded in Target/Dual mode, it creates QPair to support
MQ and allocates resources for each QPair. This Qpair initialization is
delayed until the FW personality is changed to Dual/Target mode by
issuing chip reset. At the time of chip reset firmware is re-initilized
in correct personality all the QPairs are initialized by sending
MBC_INITIALIZE_MULTIQ (001Fh).
This patch fixes memory leak by adding check to issue
MBC_INITIALIZE_MULTIQ command only while deleting rsp/req queue when the
flag is set for initiator mode, and clean up QPair resources correctly
during the driver unload. This MBX does not need to be issued for
Target/Dual mode because chip reset will reset ISP.
Fixes: d65237c7f0 ("scsi: qla2xxx: Fix mailbox failure while deleting Queue pairs")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If user swaps one target port for another target port for same switch
port, the new target port is not being recognized by the driver. Current
code assumes that old Target port has recovered from link down. The fix
will ask switch what is the WWPN of a specific NportID (GPNID) rather
than assuming it's the same Target port which has came back.
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch returns discovery state machine back to Login Complete.
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When NPort Handle is in use, driver needs to mark the handle as used and
pick another. Instead, the code clears the handle and re-pick the same
handle.
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3O85
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: qla2xxx-upstream@qlogic.com
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Tested-by: Bart Van Assche <Bart.VanAssche@wdc.com>
In some environments, user can choose to not enable SCSI-MQ but wants to
use FC-NVMe feature of the driver. Since driver relies on Q-Pairs to
allocate FC-NVMe resources, use existing module parameter to create
Q-Pairs when FC-NVMe is enabled.
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we discovered a topology that is N2N then we will issue a login to
the target. If our WWPN is bigger than the target's WWPN then we will
initiate login, otherwise we will just wait for the target to initiate
login.
[mkp: many whitespace errors]
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use *_pool_zalloc rather than *_pool_alloc followed by memset with 0.
Found by coccinelle spatch "api/alloc/pool_zalloc-simple.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After relogin is sucessful, "send_els_logo" flag needs to be
reinitialized. This will allow next re-login to happen successfully.
In target mode, this flag was not reset correctly, causing IO's failure
during reset recovery and port ON/OFF test cases from initiator.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Darren Trap <darren.trap@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When RSCN is delivered for specific remote port. Use ADISC to verify the
session is still valid or not.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If SNS fabric login fails, set loop resync flag to retry via dpc.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SFP can come in 2 formats: short range/SR and long range/LR. For LR,
user the can increase the number of Buffer to Buffer credits between end
points via Cavium's command line tool. By default, FW uses a lower BB
Credit value optimized for SR. This patch will read the SFP for each
link up event and during chip reset sequence. If the SFP type and
setting are mismatch, then the chip is reset 1 time to use the
appropriate setting.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For NPIV ports, call configure_hba() so that NPIV ports can proceed to
loop initialization.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver held spinlocks during callbacks for NVME errors which
resulted in a deadlock because recovery LS cmds needed the same lock.
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following typos/spelling mistakes:
"attribure" -> "attribute"
"suppored" -> "supported"
"Symobilic" -> "Symbolic"
"iteself" -> "itself"
"reqeust" -> "request"
"nvme_wait_on_comand" -> "nvme_wait_on_command"
"bount" -> "bound"
"captrue_mask" -> "capture_mask"
"tempelate" -> "template"
..and also unwrap a line to fix a checkpatch warning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds switch command support for FC-4 type of FC-NVMe (0x28)
for resgistering HBA port to the management server. RFT_ID command is
used to register FC-4 type of 0x28 and RFF_ID is used to register FC-4
features bits for FC-NVMe port.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-By: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code provides the interfaces to register remote and local ports of
FC4 type 0x28 with the FC-NVMe transport and transports the requests
(FC-NVMe FC link services and FC-NVMe commands IUs) to the fabric. It
also provides the support for allocating h/w queues and aborting FC-NVMe
FC requests.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added logic to change the login process into an optional PRIL step for
FC-NVMe ports as a separate operation, such that we can change type to
0x28 (NVMe).
Currently, the driver performs the PLOGI/PRLI together as one operation,
but if the discovered port is an NVMe port then we first issue the PLOGI
and then we issue the PRLI. Also, the fabric discovery logic was changed
to mark each discovered FC NVMe port, so that we can register them with
the FC-NVMe transport later.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add call back to door bell for qpair. This help reduce access to
qla_hw_data structure, in order to reduce cach thrash.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For ISP27XX, use shadow register to read FW provided REQQ's consumer
index. The shadow register is dma'ed by firmware.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Move chip_reset, enable_class_2 fields from qla_hw_data to qla_qpair
to reduce cache thrash for target MQ.
- Optimizations to reduce unnecessary memory load for good path io.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add fw_started flag to qpair to reduce cache thrash. This reduce access
to qla_hw_data structure by each qpair.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In target mode driver, queue pairs are not created during driver load
time, instead they are created at the configuration time after chip
reset. If a user tries to load/unload driver after queue pairs are
created, then there would be mailbox failure, while deleting queue
pairs. Flag is added to check if queue pairs are created or not. Queue
pairs will be deleted only If they were created during target
configuration.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable Multi Queue for Target mode. At Initiator LUN scan time, each LUN
is assign to a QPair. Each QPair is affinitize to certain CPU. When new
cmd arrives from the wire, the lunid is used to search for qpair. The
qpair's affinitized cpuid will be used to queue up the work element.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In Current code, Req Q 0, RespQ 0 & hardware_lock are the main resources
for sending and process completion of Target IO. These resources are now
referenced behind a new qpair/"struct qla_qpair base_qpair". Main path
IO handle will access those resources via the qpair pointer in
preparation for Target MQ.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes following 0-day kernel build warnings:
drivers/scsi/qla2xxx/qla_init.c:6407:50: warning: format '%lx' expects
argument of type 'long unsigned int', but argument 5 has type 'unsigned
int' [-Wformat=]
drivers/scsi/qla2xxx/qla_init.c:6709:50: warning: format '%lx'
expects argument of type 'long unsigned int', but argument 5 has
type 'unsigned int' [-Wformat=]
Fixes: b95b9452aa ("scsi: qla2xxx: Fix crash due to mismatch mumber of Q-pair creation for Multi queue")
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Accelerate generation of SCSI busy to let initiators slow down when
target is running low in resources.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Previously, the ql2xexchoffld module parameter was used to control the
max number of exchanges to be offload onto host memory.
Module parameter ql_dm_tgt_ex_pct was used to control the percentage of
exchanges allocated to the Target side.
With this patch, module parameter ql_dm_tgt_ex_pct is no longer used to
control exchanges for the driver. New module parameter ql2xiniexchg is
added to control exchanges between target mode and initiator mode.
With the updated module parameters, users can control the exact number
of exchanges for either Initiator or Target. The exchange offload
feature will be automatically enabled when the total number of exchanges
exceeds 2048 limit.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tell FW to track exchange/cmd state to prevent driver from using stale
exchange or exchange that is not meant for this command.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Assign unique id to all traces and logs for debug purpose.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Name server login is normally handle by FW. In some rare case where one
of the switches is being updated, name server login could get
affected. Trigger relogin to name server when driver detects this
condition.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver added mechanism to move ABTS/PUREX/RIDA mailbox to
ATIO queue as part of commit id 41dc529a46
("qla2xxx: Improve RSCN handling in driver").
This patch adds a check to only allow ABTS/PURX/RIDA
to be moved to ATIO Queue for ISP83XX and ISP27XX.
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
when driver is loaded with Multi Queue enabled, it was noticed that
there was one less queue pair created.
Following message would indicate this:
"No resources to create additional q pair."
The result of one less queue pair means that system can crash, if the
block mq layer thinks there is an extra hardware queue available, and
the driver will use a NULL ptr qpair in that instance.
Following stack trace is seen in one of the crash:
irq_create_affinity_masks+0x98/0x530
irq_create_affinity_masks+0x98/0x530
__pci_enable_msix+0x321/0x4e0
mutex_lock+0x12/0x40
pci_alloc_irq_vectors_affinity+0xb5/0x140
qla24xx_enable_msix+0x79/0x530 [qla2xxx]
qla2x00_request_irqs+0x61/0x2d0 [qla2xxx]
qla2x00_probe_one+0xc73/0x2390 [qla2xxx]
ida_simple_get+0x98/0x100
kernfs_next_descendant_post+0x40/0x50
local_pci_probe+0x45/0xa0
pci_device_probe+0xfc/0x140
driver_probe_device+0x2c5/0x470
__driver_attach+0xdd/0xe0
driver_probe_device+0x470/0x470
bus_for_each_dev+0x6c/0xc0
driver_attach+0x1e/0x20
bus_add_driver+0x45/0x270
driver_register+0x60/0xe0
__pci_register_driver+0x4c/0x50
qla2x00_module_init+0x1ce/0x21e [qla2xxx]
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Milan P Gandhi <mgandhi@redhat.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current driver wait for FW to be in the ready state before
processing in-coming commands. For Arbitrated Loop or
Point-to- Point (not switch), FW Ready state can take a while.
FW will transition to ready state after all Nports have been
logged in. In the mean time, certain initiators have completed
the login and starts IO. Driver needs to start processing all
queues if FW is already started.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
For target mode, when new scsi command arrive, driver first performs
a look up of the SCSI Host. The current look up method is based on
the ALPA portion of the NPort ID. For Cisco switch, the ALPA can
not be used as the index. Instead, the new search method is based
on the full value of the Nport_ID via btree lib.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The Mailbox interface is currently over subscribed. We like
to reserve the Mailbox interface for the chip managment and
link initialization. Any non essential Mailbox command will
be routed through the IOCB interface. The IOCB interface is
able to absorb more commands.
Following commands are being routed through IOCB interface
- Get ID List (007Ch)
- Get Port DB (0064h)
- Get Link Priv Stats (006Dh)
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If the remote port have started the login process, then the
PLOGI and PRLI should be back to back. Driver will allow
the remote port to complete the process. For the case where
the remote port decide to back off from sending PRLI, this
local port sets an expiration timer for the PRLI. Once the
expiration time passes, the relogin retry logic is allowed
to go through and perform login with the remote port.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- enable dual mode (initiator + target) qla2xxx operation. (Quinn +
Himanshu)
- add a framework for qla2xxx async fabric discovery. (Quinn +
Himanshu)
- enable iscsi PDU DDP completion offload in cxgbit/T6 NICs. (Varun)
- fix target-core handling of aborted failed commands. (Bart)
- fix a long standing target-core issue NULL pointer dereference with
active I/O LUN shutdown. (Rob Millner + Bryant + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (44 commits)
target: Add counters for ABORT_TASK success + failure
iscsi-target: Fix early login failure statistics misses
target: Fix NULL dereference during LUN lookup + active I/O shutdown
target: Delete tmr from list before processing
target: Fix handling of aborted failed commands
uapi: fix linux/target_core_user.h userspace compilation errors
target: export protocol identifier
qla2xxx: Fix a warning reported by the "smatch" static checker
target/iscsi: Fix unsolicited data seq_end_offset calculation
target/cxgbit: add T6 iSCSI DDP completion feature
target/cxgbit: Enable DDP for T6 only if data sequence and pdu are in order
target/cxgbit: Use T6 specific macros to get ETH/IP hdr len
target/cxgbit: use cxgb4_tp_smt_idx() to get smt idx
target/iscsi: split iscsit_check_dataout_hdr()
target: Remove command flag CMD_T_DEV_ACTIVE
target: Remove command flag CMD_T_BUSY
target: Move session check from target_put_sess_cmd() into target_release_cmd_kref()
target: Inline transport_cmd_check_stop()
target: Remove an overly chatty debug message
target: Stop execution if CMD_T_STOP has been set
...
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following warning reported by the "smatch" static checker:
drivers/scsi/qla2xxx/qla_init.c:3910 qla2x00_alloc_fcport()
warn: use 'flags' here instead of GFP_XXX?
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch simplifies SRB structure usage in driver.
- Simplify sp->done() and sp->free() interfaces.
- Remove sp->fcport->vha to use vha pointer from sp.
- Use sp->vha context in qla2x00_rel_sp().
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Current code blindly does State Change Registration when
the link is up. Move SCR behind fabric scan, so that arbitrated
loop scan would not get erroneous error message.
Some of the other improvements are as follows
- Add session deletion for TPRLO and send acknowledgment for TPRLO.
- Enable FW option to move ABTS, RIDA & PUREX from RSPQ to ATIOQ.
- Save NPort ID early in link init.
- Move ABTS & RIDA to ATIOQ helps in keeping command ordering and
link up sequence ordering.
- Save Nport ID and update VP map so that SCSI CMD/ATIO won't be dropped.
- fcport alloc does the initializes memory to zero. Remove memset to
zero since It might corrupt link list.
- Turn off Registration for State Change MB in loop mode.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add switch to allow both Initiator Mode & Target
mode to operate at the same time.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Currently code performs a full scan of the fabric for
every RSCN. Its an expensive process in a noisy large SAN.
This patch optimizes expensive fabric discovery process by
scanning switch for the affected port when RSCN is received.
Currently Initiator Mode code makes login/logout decision without
knowledge of target mode. This causes driver and firmware to go
out-of-sync. This framework synchronizes both initiator mode
personality and target mode personality in making login/logout
decision.
This patch adds following capabilities in the driver
- Send Notification Acknowledgement asynchronously.
- Update session/fcport state asynchronously.
- Create a session or fcport struct asynchronously.
- Send GNL asynchronously. The command will ask FW to
provide a list of FC Port entries FW knows about.
- Send GPDB asynchronously. The command will ask FW to
provide detail data of an FC Port FW knows about or
perform ADISC to verify the state of the session.
- Send GPNID asynchronously. The command will ask switch
to provide WWPN for provided NPort ID.
- Send GPSC asynchronously. The command will ask switch
to provide registered port speed for provided WWPN.
- Send GIDPN asynchronously. The command will ask the
switch to provide Nport ID for provided WWPN.
- In driver unload path, schedule all session for deletion
and wait for deletion to complete before allowing driver
unload to proceed.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
[ bvanassche: fixed spelling in patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Current code merges qla_tgt_sess and fc_port structure
into single fc_port structure representing same I-T nexus.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
[ bvanassche: fixed spelling of patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Soft reset and Risc reset should take 100uS to complete.
This change pad the timeout up to 400uS, which should be
plenty.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
- Fix race condition between dpc_thread accessing Multiqueue resources
and qla2x00_remove_one thread trying to free resource.
- Fix out of order free for Multiqueue resources. Also, Multiqueue
interrupts needs a workqueue. Interrupt needed to stop before
the wq can be destroyed.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replaced existing multiple queue functionality with framework
that allows for the creation of pairs of request and response queues,
either at start of day or dynamically.
Queue pair creation depend on module parameter "ql2xmqsupport",
which need to be enabled to create queue pair.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Properly initialize IO statistics to avoid initial 0xFFFFFFF (-1) values.
Cleanup/simplify usage of pointer to statistics structure.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When VP decoupling enabled, there could be a window where, FLOGI from initiators
can be dropped before VP0 is enabled, causing link level recovery.
Retry FLOGI to avoid link level recovery.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we fail to queue an srb for an async login we should set the
relogin flag so it will be retried as the reason for the queuing
failure was most likely transient. Failure to do this can lead to
failed paths as login is never retried if the relogin flag is not
set.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set bit 12 of additional firmware options 3 to let firmware
hold status IOCB until ABTS response is received from Target.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ Upstream Commit 84e32a06f4 ]
Commit 84e32a0 ("qla2xxx: Use pci_enable_msix_range() instead of
pci_enable_msix()") introduced a regression when target mode is enabled.
In qla24xx_enable_msix(), ha->max_rsp_queues was incorrectly set
to a value higher than the number of response queues allocated causing
an invalid dereference. Specifically here in qla2x00_init_rings():
*rsp->in_ptr = 0;
Add additional check to make sure the pointer is valid. following
call stack will be seen
---- 8< ----
RIP: 0010:[<ffffffffa02ccadc>] [<ffffffffa02ccadc>] qla2x00_init_rings+0xdc/0x320 [qla2xxx]
RSP: 0018:ffff880429447dd8 EFLAGS: 00010082
....
Call Trace:
[<ffffffffa02ceb40>] qla2x00_abort_isp+0x170/0x6b0 [qla2xxx]
[<ffffffffa02c6f77>] qla2x00_do_dpc+0x357/0x7f0 [qla2xxx]
[<ffffffffa02c6c20>] ? qla2x00_relogin+0x260/0x260 [qla2xxx]
[<ffffffff8107d2c9>] kthread+0xc9/0xe0
[<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90
[<ffffffff8172cc6f>] ret_from_fork+0x3f/0x70
[<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90
---- 8< ----
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Driver has following initialization sequence for Target mode
1. Driver initialization starts
2. ISP Abort is scheduled when the target is enabled.
qla2xxx [0000:04:00.0]-4807:25: ISP abort scheduled
qla2xxx [0000:04:00.0]-00af:25: Performing ISP error recovery - ha=ffff880caa9e0000.
3. DPC thread starts the ISP Abort
4. While DPC is resetting the chip and initializing the firmware, we get
async events from the firmware about P2P mode, LOOP UP and PORT UPDATE.
5. PRLI from a initiator is delivered to us followed by a PLOGI and then a
SCSI command which creates a session.
6. If the SCSI command is a WRITE in this case, we issue XFR RDY and it
gets dropped as can be seen with messages RESET-XFR because ISP Abort
is still active
qla2xxx [0000:04:00.0]-e902:25: RESET-XFR active/old-count/new-count = 1/1/1.
7. If the SCSI command is a READ, we issue RESPONSE and they get dropped
as well because Abort is still active.
qla2xxx [0000:04:00.0]-e901:25: RESET-RSP active/old-count/new-count = 1/1/1
8. Now eventually, ISP Abort finishes clearing the DPC flags.
qla2xxx [0000:04:00.0]-8822:25: qla2x00_abort_isp succeeded.
qla2xxx [0000:04:00.0]-4808:25: ISP abort end.
9. Since we dropped SCSI commands silently (without any responses sent
to the initiator) initiator waits for a SCSI timeout (which is 60
seconds in our case), Sends an ABTS which fails since there
no se_cmd found for the tag that ABTS is referencing as the
commands were cleaned up in Step 6 and 7.
10. Initiator send an IO after the ABTS which succeed fine.
To fix the above case, the following changes have been made:
- To prevent target from dropping commands silently, use the online flag
instead to check for an active chip reset. Once the port is online during
a chip reset phase, we are good to process the commands.
- Clean up qla2x00_restart_isp to not set the online flag and process ATIO
as it is unnecessary. During a chip reset, interrupts are enabled only
after setting the online flag to 1, so ATIO's won't be missed and hence
no need to process ATIO's after setting the online flag.
Signed-off-by: Dilip Kumar Uppugandla <dilip@purestorage.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
99% of the time the ATIOQ has SCSI command. The other 1% of time
is something else. Most of the time this interrupt does not need
to hold the hardware_lock. We're moving the ATIO interrupt thread
to a different lock to reduce lock contention.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
DebugFS now will show fw_resource_count node.
FW Resource count
Original TGT exchg count[0]
current TGT exchg count[0]
original Initiator Exchange count[2048]
Current Initiator Exchange count[2048]
Original IOCB count[2078]
Current IOCB count[2067]
MAX VP count[254]
MAX FCF count[0]
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch enables Exchange offload support in Qlogic ISP.
To enable exchange offload with Qlogic ISP24XX/25XX/26XX,
set module parameter ql2xexchoffld to any non-zero number.
This will alow ISP firmware to store exchange data structures
used by firmware to host memory provided by driver. ISP firmware
can supports upto 32k total active exchanges.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch enables Extended Logins support in Qlogic ISP.
To enable extended login with Qlogic ISP24XX/25XX/26XX,
set module parameter ql2xexlogins to any non-zero number.
This will alow ISP firmware to store port database structure
information of remote login sessions to host memory provided
by driver. ISP firmware supports upto 16k total logins.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This includes one new driver: cxlflash plus the usual grab bag of updates for
the major drivers: qla2xxx, ipr, storvsc, pm80xx, hptiop, plus a few assorted
fixes.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJV5eGiAAoJEDeqqVYsXL0MCpwH/AoneZOPeCx0YdTlyiojasi4
Kc7ECmV9IJJoMoCbP8grwStvynYyCHDSphYmqopZPRlD021eG8ota2uRTHEGJI+q
SoiZUlq8ti8xgnD55mubwO+UNF+zoELMyHUok2pGzBoZN5alA6nvKuNY7Hif3P3b
YMT490oWQLjWmJkMW8TbpMn9nHpW0dfbP323uaggWsMy3CSI707+x36FLi1/ICg6
MZRyv4aESAcauZGUI5EG+SrIl3OBQX7snsYXyuqD3biGqzbGc3p3L9uWG1qXHDbM
OSGXhN+our0WYHCV1/UrGz7/IAWW1UU0W2qgCBwkXkDjkXJ4jqd36zLJxeuhSpE=
=KOmP
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This includes one new driver: cxlflash plus the usual grab bag of
updates for the major drivers: qla2xxx, ipr, storvsc, pm80xx, hptiop,
plus a few assorted fixes.
There's another tranch coming, but I want to incubate it another few
days in the checkers, plus it includes a mpt2sas separated lifetime
fix, which Avago won't get done testing until Friday"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (85 commits)
aic94xx: set an error code on failure
storvsc: Set the error code correctly in failure conditions
storvsc: Allow write_same when host is windows 10
storvsc: use storage protocol version to determine storage capabilities
storvsc: use correct defaults for values determined by protocol negotiation
storvsc: Untangle the storage protocol negotiation from the vmbus protocol negotiation.
storvsc: Use a single value to track protocol versions
storvsc: Rather than look for sets of specific protocol versions, make decisions based on ranges.
cxlflash: Remove unused variable from queuecommand
cxlflash: shift wrapping bug in afu_link_reset()
cxlflash: off by one bug in cxlflash_show_port_status()
cxlflash: Virtual LUN support
cxlflash: Superpipe support
cxlflash: Base error recovery support
qla2xxx: Update driver version to 8.07.00.26-k
qla2xxx: Add pci device id 0x2261.
qla2xxx: Fix missing device login retries.
qla2xxx: do not clear slot in outstanding cmd array
qla2xxx: Remove decrement of sp reference count in abort handler.
qla2xxx: Add support to show MPI and PEP FW version for ISP27xx.
...
Execute qla25xx_manipulate_risc_semaphore() only for
ssdid 0x0175 and 0x0240.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Whether htonl() or __constant_htonl() is used, if the argument
is a constant the conversion happens at compile time. Hence leave
out the __constant_ prefix for this and other endianness
conversion functions. This improves source code readability.
[jejb: checkpatch fixes]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Detected these variables by building with W=1.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
There are multiple reasons for disabling this:
1. It provides no functional benefit. We pretty much only get a few more
sysfs entries for each port, but all that information is already
available from /sys/kernel/debug/target/qla-session-X
2. It already only works in private-loop mode. By disabling we'll be
getting more uniform behavior with fabric mode.
3. It creates complications for the new PLOGI handling mechanism:
scsi_transport_fc port deletion timer could race with new session
from initiator and cause logout after successful login.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
RSCN processing in qla2xxx driver can run in parallel with ELS/IO
processing. As such the decision to remove disappeared fc port's
session could be stale, because a new login sequence has occurred
since and created a brand new session.
Previous mechanism of dealing with this by delaying deletion request
was prone to erroneous deletions if the event that was supposed to
cancel the deletion never arrived or has been delayed in processing.
New mechanism relies on a time-like generation counter to serialize
RSCN updates relative to ELS/IO updates.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- keep qla_tgt_sess object on the session list until it's freed
- modify use of sess->deleted flag to differentiate delayed
session deletion that can be cancelled from irreversible one:
QLA_SESS_DELETION_PENDING vs QLA_SESS_DELETION_IN_PROGRESS
- during IN_PROGRESS deletion all newly arrived commands and TMRs will
be rejected, existing commands and TMRs will be terminated when
given by the core to the fabric or simply dropped if session logout
has already happened (logout terminates all existing exchanges)
- new PLOGI will initiate deletion of the following sessions
(unless deletion is already IN_PROGRESS):
- with the same port_name (with logout)
- different port_name, different loop_id but the same port_id
(with logout)
- different port_name, different port_id, but the same loop_id
(without logout)
- additionally each new PLOGI will store imm notify iocb in the
same port_name session being deleted. When deletion process
completes this iocb will be acked. Only the most recent PLOGI
iocb is stored. The older ones will be terminated when replaced.
- new PRLI will initiate deletion of the following sessions
(unless deletion is already IN_PROGRESS):
- different port_name, different port_id, but the same loop_id
(without logout)
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To fix some issues talking to ESX, this patch modifies the qla2xxx driver
so that it never logs into remote ports. This has the side effect of
getting rid of the "rports" entirely, which means we never log out of
initiators and never tear down sessions when an initiator goes away.
This is mostly OK, except that we can run into trouble if we have
initiator A assigned FC address X:Y:Z by the fabric talking to us, and
then initiator A goes away. Some time (could be a long time) later,
initiator B comes along and also gets FC address X:Y:Z (which is
available again, because initiator A is gone). If initiator B starts
talking to us, then we'll still have the session for initiator A, and
since we look up incoming IO based on the FC address X:Y:Z, initiator B
will end up using ACLs for initiator A.
Fix this by:
1. Handling RSCN events somewhat differently; instead of completely
skipping the processing of fcports, we look through the list, and if
an fcport disappears, we tell the target code the tear down the
session and tell the HBA FW to release the N_Port handle.
2. Handling "port down" events by flushing all of our sessions. The
firmware was already releasing the N_Port handle but we want the
target code to drop all the sessions too.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[ Upstream commit ef86cb2059 ]
This patch fixes a kernel panic for qla2xxx Target core
Module driver introduced by a fix in the qla2xxx initiator code.
Commit ef86cb2 ("qla2xxx: Mark port lost when we receive an RSCN for it.")
introduced the regression for qla2xxx Target driver.
Stack trace will have following signature
--- <NMI exception stack> ---
[ffff88081faa3cc8] _raw_spin_lock_irqsave at ffffffff815b1f03
[ffff88081faa3cd0] qlt_fc_port_deleted at ffffffffa096ccd0 [qla2xxx]
[ffff88081faa3d20] qla2x00_schedule_rport_del at ffffffffa0913831[qla2xxx]
[ffff88081faa3d50] qla2x00_mark_device_lost at ffffffffa09159c5[qla2xxx]
[ffff88081faa3db0] qla2x00_async_event at ffffffffa0938d59 [qla2xxx]
[ffff88081faa3e30] qla24xx_msix_default at ffffffffa093a326 [qla2xxx]
[ffff88081faa3e90] handle_irq_event_percpu at ffffffff810a7b8d
[ffff88081faa3ee0] handle_irq_event at ffffffff810a7d32
[ffff88081faa3f10] handle_edge_irq at ffffffff810ab6b9
[ffff88081faa3f30] handle_irq at ffffffff8100619c
[ffff88081faa3f70] do_IRQ at ffffffff815b4b1c
--- <IRQ stack> ---
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is the usual grab bag of driver updates (lpfc, qla2xxx, storvsc, aacraid,
ipr) plus an assortment of minor updates. There's also a major update to
aic1542 which moves the driver into this millenium.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVL/DEAAoJEDeqqVYsXL0MOwgIALPlgI0aMAtX5wLxzPMLB/2j
fhNlsB9XZ6TeYIqE7syOY7geVJqsbACMGmDhGHs5Gt6jkTnwix/G49x3T1PXBODZ
frz8GgNB6iGSqfCp+YbhJkTNHdudDIy2LrQ92EzNMb2+x0v6KTYTSq2dekgrC1zK
8GUZ9bEzuxEGaBx9TK/Sy6H8QpvMtqqJig2eCL189U3JMMU3okWtSGya708u5Whh
knbUgraMxFWNs+oHJHFclVYvekP+61i/TVyacQEM4KLDsmlxsLn49eRdiGMY6rpX
LgDIvMjggQhbY2WcCXzetF7tsFFl0joJp1wFK1fUn9YN5e+J3MRWYVBDt8FMPX8=
=OBny
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, qla2xxx, storvsc,
aacraid, ipr) plus an assortment of minor updates. There's also a
major update to aic1542 which moves the driver into this millenium"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (106 commits)
change SCSI Maintainer email
sd, mmc, virtio_blk, string_helpers: fix block size units
ufs: add support to allow non standard behaviours (quirks)
ufs-qcom: save controller revision info in internal structure
qla2xxx: Update driver version to 8.07.00.18-k
qla2xxx: Restore physical port WWPN only, when port down detected for FA-WWPN port.
qla2xxx: Fix virtual port configuration, when switch port is disabled/enabled.
qla2xxx: Prevent multiple firmware dump collection for ISP27XX.
qla2xxx: Disable Interrupt handshake for ISP27XX.
qla2xxx: Add debugging info for MBX timeout.
qla2xxx: Add serdes read/write support for ISP27XX
qla2xxx: Add udev notification to save fw dump for ISP27XX
qla2xxx: Add message for sucessful FW dump collected for ISP27XX.
qla2xxx: Add support to load firmware from file for ISP 26XX/27XX.
qla2xxx: Fix beacon blink for ISP27XX.
qla2xxx: Increase the wait time for firmware to be ready for P3P.
qla2xxx: Fix crash due to wrong casting of reg for ISP27XX.
qla2xxx: Fix warnings reported by static checker.
lpfc: Update version to 10.5.0.0 for upstream patch set
lpfc: Update copyright to 2015
...
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
When we have an rport disconnect we race during rport deletion and
re-connection resulting in a panic. When we do this, we call
fc_remote_port_del() just before we do the calls to re-establish the
session with the FC transport with fc_remote_port_add() and then
fc_remote_port_rolechg().
If we remove the call to fc_remote_port_del() before re-establishing
the connection this prevents the race. This patch has resolved this
for multiple customers via test kernels.
Suggested by Chad Dupuis, implemented and tested by Laurence Oberman.
Signed-off-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A chip reset can occur after driver submits command to the stack. Abort
command processing if a chip reset has occurred or in progress when you
get a follow up for a command.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If we fail to load one of the segments of firmware fail the operation
instead of trying to continue which will lead to a system crash since
the pointers to the next segment will not be updated correctly.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For FA-WWPN capable device, ISP2031 and ISP27XX, when loop
dead is detected by a driver, restore WWPN from NVRAM.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Declaration error of mb array in qla2x00_iidma_fcport cause data
to be written beyond the array. This ends up causing stack corruption.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add support for the D-port (diagnostic port) fabric switch feature.
(Fabric Switch initiates loopback style port testing)
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use the zeroing function instead of dma_alloc_coherent & memset(,0,)
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Attempting to do any logins from the SCSI reset handler can lead to a deadlock
scenario if a rport times out and the FC transport layer. Move doing any port
logins to the DPC thread so as not to impede the progress of the SCSI error
handler thread and avoid deadlock situations.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For ISP27xx use the request/response queue index shadow registers
to avoid directly access them on the PCI bus.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes some build warnings such as:
drivers/scsi/qla2xxx/qla_attr.c:162:6: warning: format '%lx' expects argument of
type 'long unsigned int', but argument 6 has type 'size_t'"
and
drivers/scsi/qla2xxx/qla_init.c:5198:7: warning: format '%lx' expects argument
of type 'long unsigned int', but argument 5 has type 'uint32_t' [-Wformat]
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Send aborts to the firmware via the request/response queue mechanism.
Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Fix interpreting the wrong IOCB type for task management
functions in the response path.
- Merge the task management function handling for various adapters.
Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the execute firmware command fails we do not stop the rest of the
initialization process which will continue to fail so if we encounter an error
simply short circuit the process.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For supported ISPS, Read asic temperature by calling the
GET PARAMS (type C) mailbox command.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The patch changes a specifier used to output some variables. Instead of using
stack for each byte the '%*ph[CN]' allows to take a one pointer and prints
entire buffer as a hexadecimal string with the separator ':' or ''.
Signed-off-by: Oleksandr Khoshaba <Oleksandr.Khoshaba@gmail.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
At the end of qla2x00_configure_hba() we know that rval == QLA_SUCCESS.
Hence remove the dead code.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
System crashes, in initiator mode operation, with
qla2xxx_copy_atioqueues() in stack trace when firmware dump is
attempted.
Check for atio_q_length alone does not indicate if atio_ring is
allocated, make explicit check of atio_ring to avoid the crash.
Applicable to ISP24xx, ISP25xx, ISP81xx & ISP83xx line of HBAs.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The original patch was not covering all the adapters and firmwares.
This commit reverts 3a11711ad0.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Give priority to I2C thermal.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently,the driver is processes RSCNs for each new NPIV ports that is created.
Processing the RSCN includes a name server query to see what has changed at the
name server side. The name server query is performed by the physical port and
each virtual port on the physical adapter (since the RSCN is passed to each
virtual port for processing). As the number of virtual ports being created
increases, this causes a lot of traffic and busies the firmware.
Processing the RSCN for a virtual port we already have a priori knowledge of is
not necessary so check the 24-bit fabric ID of the RSCN entry and skip
processing it if the RSCN is for a virtual port we already know about.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
BSG code path increments ref count in the send path, but does not
decrement in the return path leading to hang during unload of the
driver.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
To avoid continually doing ISP resets when get loop id fails to
obtain the adapter loop id, first try to do a link initialization.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Base the number of outstanding requests the driver will keep track of on the
available resources instead of being hard-coded.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Parameterize qla2x00_get_link_speed_str() to be generic on link speed.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Try to acquire the semaphore; if semaphore is hung then acquire it by force.
The ISP reset clears the semaphore, thereby implicitly releasing it.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Rather than returning stale mailbox values.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Lockdep reports:
=== [ cut here ] ===
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
3.6.0-0.0.0.28.36b5ec9-default #1 Not tainted
---------------------------------------------------------
qla2xxx_1_dpc/368 just changed the state of lock:
(&(&ha->vport_slock)->rlock){+.....}, at: [<ffffffffa009b377>] qla2x00_configure_hba+0x197/0x3c0 [qla2xxx]
but this lock was taken by another, HARDIRQ-safe lock in the past:
(&(&ha->hardware_lock)->rlock){-.....}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&ha->vport_slock)->rlock);
local_irq_disable();
lock(&(&ha->hardware_lock)->rlock);
lock(&(&ha->vport_slock)->rlock);
<Interrupt>
lock(&(&ha->hardware_lock)->rlock);
=== [ cut here ] ===
Fix the potential deadlock by disabling IRQs while holding ha->vport_slock.
Reported-and-tested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Stale information in the temporary fcport created in
qla2x00_configure_local_loop() causes qla2x00_get_port_database() call
to fail. This reschedules scan, which gets stuck continuously in the
rescheduling-of-scan loop due to the failure.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Update the driver copyright from 2003-2011 to 2003-2012.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Minor changes to support loopback functionality with ISP83xx CNAs.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Store used fcport loop_id's in a bitmap so that as opposed to looping through
all fcports to find the next free loop_id, new loop_id lookup can be just be
done via bitops.
[jejb: plus fix for incorrect LOOPID_MAP_SIZE from Andrew Vasquez]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The PCIE capability offset is saved during PCI bus walking. It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it. Also, pci_is_pcie is a
better way of determining if the device is PCIE or not (as it uses the
same saved PCIE capability offset).
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add LLD target mode for >= 24xx series HW. This code was originally based on
external qla2x00t module based on 8.02.01-k4, and has been refactored to
push the bulk of code into mainline qla2xxx.ko LLD -> qla_target.c.
The implementation uses internal workqueues for I/O context submission
into tcm_qla2xxx code, and includes the struct qla_tgt_func_tmpl API for
external interaction to allow qla2xxx LDD to function without direct
target-core dependencies:
It also enables qla_target.c usage within existing qla2xxx LLD code.
This includes:
*) Addition of target mode specific members to existing data
structures in qla_def.h and struct qla_hw_data->tgt_ops using
qla_target.h:struct qla_tgt_func_tmpl
*) Addition of struct qla_tgt_func_tmpl and direct calls into
qla_target.c logic w/ qlt_* prefixed functions.
*) Addition of qla_iocb.c:qla2x00_req_pkt() for ring processing, and
qla2x00_issue_marker() for handling request/response queue processing
for target mode operation
*) Addition of various qla_tgt_mode_enabled() logic checks in
qla24xx_nvram_config(), qla2x00_initialize_adapter(), qla2x00_rff_id(),
qla2x00_abort_isp(), qla24xx_modify_vp_config(), and
qla2x00_vp_abort_isp().
By default the new qlini_mode module parameter is setting initiator-mode
to 'enabled' in order for 'modprobe qla2xxx' to continue to function as
expected in initiator only mode. Enabling target-mode operation will
currently require a:
modprobe qla2xxx qlini_mode="disabled"
in order to explictly disabled initiator mode and allow target-mode
to be enabled via tcm_qla2xxx configfs fabric callers.
(nab: Convert to qlini_mode='enabled' by default in qla_target.c)
(joern: Remove loop_id from qla_tgt_make_local_sess() arguments +
Remove unused s_id + fix s_id endianness bug +
simplify qla_tgt_abort_work)
(gerard: fix section __exit mismatch in qla_tgt_exit)
(arun: Capture ATIO queue during firmware dump + Send SCR in target mode +
Target mode review comments)
(roland: Don't create duplicate target sessions to address tearing down
ACLs with IO in flight + Add missing call to qlt_fc_port_deleted
call during qla2x00_schedule_rport_del timeout)
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The field vp_idx in struct fc_port is a redundant/mirror copy of
the same field in struct scsi_qla_host;
struct fc_port has a pointer vha to scsi_qla_host which allows
the original copy of vp_idx to be readily accessed.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently stats is part of ha data structure, common for physical and virtual
ports. Moved the stats to vha, each port will have its own stat.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Replace "Inconisistent" with "Inconsistent" in drivers/scsi/qla2xxx/qla_init.c
Signed-off-by: Raul Porcel <armin76@gentoo.org>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A device logout sent in the delete path of a fcport would clear the
port handle binding inside the firmware. This could lead to queued
work items for the fcport, if any, getting incorrect results. This
patch fixes the issue by checking for device name changes after a
call to get port database.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add a field to the qla_hw_data struct to allow us to set the maximum number of
fabric devices on a per adapter basis based on ISP type.
[jejb: fix up missing rval = QLA_SUCCESS to prevent uninit var warning]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Rather than continuously allocating and freeing swl within the discovery
process, simply pre-allocate it the first time that it's needed, cache it
through the rest of the lifecycle of the driver and free it at module unload.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make sure that all calls to ha->isp_ops->fabric_login() check the
return value for failure.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of processing each RSCN individually, use only the name server results
from the switch to tell the existance of a given fcport.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Rework the structures related to SRB processing to minimize the memory
allocations per I/O and manage resources associated with and completions
from common routines.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Original 'defaults' were not OUI valid.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The driver should ensure there's a sufficient number of IOCBs
to satisfy the number of scatter-gather entries specified in the
command. Add a 'count' to the control structure, srb_ctx, to use
in qla2x00_alloc_iocbs().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This provides a capability to set a priority in the FCP packet.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch contains minor fixes to our new logging infrastructure:
- Remove extranous messages.
- Re-add 'nexus' and 'hdl' information.
- Adjusted the message ids to fill up the holes.
- Display FCP_CMND priority on update.
- Log only mail box error conditions.
- Do not print "Firmware ready **** FAILED ****" if cable is unplugged.
- Drop noisy 'fw_state...curr time...' message.
- Correct nexus display during abort.
- Add a special case error-logging set to '1'.
- Catagorize I/O exception display handling.
- Correct the bsg msg code printing.
- Dont use dynamic logging after host is removed.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Minidump allows us to catpure a snapshot of the firmware/hardware states at the
time of failure for further analysis.
[jejb: added missing #include <linux/vmalloc.h>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> ]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Transitioning to a LOOP_UPDATE loop-state could cause the driver
to miss normal link/target processing. LOOP_UPDATE is a crufty
artifact leftover from at time the driver performed it's own
internal command-queuing. Safely remove this state.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The code is changed to support the new dynamic logging infrastructure.
Following are the levels added.
Default is 0 - no logging. 0x40000000 - Module Init & Probe.
0x20000000 - Mailbox Cmnds. 0x10000000 - Device Discovery.
0x08000000 - IO tracing. 0x04000000 - DPC Thread.
0x02000000 - Async events. 0x01000000 - Timer routines.
0x00800000 - User space. 0x00400000 - Task Management.
0x00200000 - AER/EEH. 0x00100000 - Multi Q.
0x00080000 - P3P Specific. 0x00040000 - Virtual Port.
0x00020000 - Buffer Dump. 0x00010000 - Misc.
0x7fffffff - For enabling all logs, can be too many logs.
Setting ql2xextended_error_logging module parameter to any of the above
value, will enable the debug for that particular level.
Do LOGICAL OR of the value to enable more than one level.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds the dynamic logging framework to the qla2xxx driver.
The user will be able to change the logging levels on the fly i.e.
without load/unload of the driver. This also enables logging to be
enabled for a particular section of the driver such as initialization,
device discovery etc.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use proper init_cb_size member which takes into account
MID/non-MID init-cb structure sizes.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The driver keeps a copy of the fw_version within the ha structure.
For ISP82xx, this local copy doesn't get updated, and as a result,
the old firmware version ends up getting displayed. This patch fixes
this issue.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add the inline function qla2x00_set_port_state() so that when a fcport state
transition happens we can log the state transition if debug messages are
enabled.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Before driver's own internal state is marked as PLOGI/PRLI
complete. This additional check closes a window seen with
dual-personality initiator/target devices where a driver's
PLOGI/PRLI request occurs within the window after the target's
PLOGI request has completed, but prior to the target's PRLI
arriving and processed by the firmware. Without this additional
check, the firmware will return port-information stating that the
port neither supports target nor initiator functions, causing the
driver to register the rport prematurely to the FC-transport
without the proper 'roles' being set.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If fabric device has invalid loop id (FC_NO_LOOP_ID) then call
qla2x00_find_new_loop_id() to attempt to obtain valid loop id.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The bit is already set upon entry.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Modifying qla24xx_get_fcp_prio() to return a 'found' status
allows the driver to short circuit the 'set FCP-priority' call
and reduce the amount of noise generated in the messages file:
scsi(5): Unable to activate fcp priority, ret=0x102
scsi(5): Unable to activate fcp priority, ret=0x102
Also make qla24xx_get_fcp_prio() static.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Quinn Tran