R-Mobile APE6, R-Car Gen2, and RZ/G1 SoCs have Cortex-A7 and/or
Cortex-A15 CPU cores, all of which have ARM architectured timers.
Force use of the ARM architectured timer on these SoCs.
This allows to:
- Remove the calls to shmobile_init_delay() from the corresponding
machine vectors,
- Remove a check in timer setup specific to R-Car Gen2,
- Remove a check in shmobile_init_delay().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
After the cleanup in r8a7779_smp_prepare_cpus(), the only remaining caller of
r8a7779_platform_cpu_kill() is in an ifdef, which leads to a build warning
without CONFIG_HOTPLUG_CPU:
arch/arm/mach-shmobile/smp-r8a7779.c:26:12: error: 'r8a7779_platform_cpu_kill' defined but not used [-Werror=unused-function]
This moves the function inside of that #ifdef to avoid the warning.
Fixes: 62f55ce683 ("ARM: shmobile: r8a7779: Stop powering down secondary CPUs during early boot")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit cad160ed0a ("ARM: shmobile: Convert file to use
cntvoff"), there's no non-SMP code left in headsmp-apmu.S.
Hence build the file for SMP only, and drop the no longer needed check
for CONFIG_SMP inside the file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
If the R-Car H1 system controller is described in DT, the rcar-sysc
driver configures SYSCIER and SYSCIMR based on the SoC-specific power
area definitions in r8a7779-sysc. The platform code still passed this
information to the rcar-sysc driver, for compatibility with old DTBs
predating commit b2df3aa487 ("ARM: dts: r8a7779: Add SYSC PM
Domains") in v4.7. The time has come to drop backwards compatibility,
and delegate everything to the DT enabled rcar-sysc driver.
After stopping powering down secondary CPUs during early boot, there is
no longer a need to force an early initialization of the rcar-sysc
driver. It will be initialized in time for secondary CPU bringup by its
early_initcall().
Hence all explicit SYSC configuration and initialization can be removed
from the R-Car H1 platform code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7779 SMP code calls rcar_sysc_power_{down,up}() to control power
to the SYSC power areas containing CPUs. This requires passing full CPU
power area parameter blocks.
Migrate the code to call the new rcar_sysc_power_{down,up}_cpu()
helpers, which just take a CPU index, and use the SYSC power area
definitions from the r8a7779-sysc driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
At .smp_prepare_cpus() time, CPUs 1-3 are still powered down:
- The bootloader doesn't enable CPUs 1-3,
- Non-boot CPUs are disabled by kexec before starting the new kernel.
Hence there is no need to try to power them down again, as it will fail
silently with -EIO anyway.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
If the R-Car system controller is described in DT, the rcar-sysc driver
configures SYSCIER and SYSCIMR based on the SoC-specific power area
definitions in r8a779*-sysc. The platform code still passed this
information to the rcar-sysc driver, for compatibility with old R-Car H2
and M2-W DTBs predating commit 8574de8619 ("ARM: dts: r8a7791: Add
SYSC PM Domains") in v4.7. The time has come to drop backwards
compatibility, and delegate everything to the DT enabled rcar-sysc
driver.
After the removal of the legacy SMP fallbacks, which powered up the SCUs
explicitly, there is no longer a need to force an early initialization
of the rcar-sysc driver. It will be initialized in time for secondary
CPU bringup by its early_initcall().
Hence all explicit SYSC configuration and initialization can be removed
from the R-Car Gen2 platform code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
After the removal of the legacy SMP fallbacks, platsmp-apmu.h is no
longer needed outside platsmp-apmu.c.
Hence remove platsmp-apmu.h, and make the functions exported previously
static. As the header file also provided forward declarations, the code
in platsmp-apmu.c must be reshuffled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
After the removal of the legacy SMP fallbacks, there are no more users
left of shmobile_smp_apmu_prepare_cpus().
Remove it, together with the legacy SMP config parser.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
cpu_leave_lowpower() is used for suspend only, not for CPU hotplug.
Hence move it from the HOTPLUG_CPU || SUSPEND section to the SUSPEND
section.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now r8a7791 no longer needs the SMP initialization fallback, it can use
the common R-Car Gen2 machine definition, and the r8a7791-specific one
can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit f89a51700d ("ARM: shmobile: r8a7791: Prioritize DT
APMU support") in v4.8, non-DT enablement of SMP was left as a fallback
for backwards compatibility with old DTBs.
The time has come to drop backwards compatibility, hence remove the
fallback code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now r8a7790 no longer needs the SMP initialization fallback, it can use
the common R-Car Gen2 machine definition, and the r8a7790-specific one
can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit f5d70b9cee ("ARM: shmobile: r8a7790: Prioritize DT
APMU support") in v4.8, non-DT enablement of SMP was left as a fallback
for backwards compatibility with old DTBs.
The time has come to drop backwards compatibility, hence remove the
fallback code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Here are the main updates for SoC support (besides DT additions) for ARM
32- and 64-bit platforms. The branch also contains defconfig updates to
turn on drivers and options as needed on the various platforms.
The largest parts of the delta are from cleanups moving platform data
and board file setup of TI platforms to ti-sysc bus drivers. There are
also some sweeping changes of eeprom and nand setup on Davinci, i.MX
and other platforms.
Samsung is removing support for Exynos5440, which was an oddball SoC
that hasn't been seen much use in designs.
Renesas is adding support for new SoCs (R-Car E3, RZ/G1C and RZ/N1D).
Linus Walleij is also removing support for ux500 (Sony Ericsson)
U8540/9540 SoCs that never made it to significant mass production and
products.
-----BEGIN PGP SIGNATURE-----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=S5wc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Here are the main updates for SoC support (besides DT additions) for
ARM 32- and 64-bit platforms. The branch also contains defconfig
updates to turn on drivers and options as needed on the various
platforms.
The largest parts of the delta are from cleanups moving platform data
and board file setup of TI platforms to ti-sysc bus drivers. There are
also some sweeping changes of eeprom and nand setup on Davinci, i.MX
and other platforms.
Samsung is removing support for Exynos5440, which was an oddball SoC
that hasn't been seen much use in designs.
Renesas is adding support for new SoCs (R-Car E3, RZ/G1C and RZ/N1D).
Linus Walleij is also removing support for ux500 (Sony Ericsson)
U8540/9540 SoCs that never made it to significant mass production and
products"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
MAINTAINERS: add NXP linux team maillist as i.MX reviewer
ARM: stm32: Don't select DMA unconditionally on STM32MP157C
arm64: defconfig: Enable PCIe on msm8996 and db820c
ARM: pxa3xx: enable external wakeup pins
ARM: pxa: stargate2: use device properties for at24 eeprom
arm64: defconfig: Enable HISILICON_LPC
arm64: defconfig: enable drivers for Poplar support
arm64: defconfig: Enable UFS on msm8996
ARM: berlin: switch to SPDX license identifier
arm: berlin: remove non-necessary flush_cache_all()
ARM: berlin: extend BG2CD Kconfig entry
OMAP: CLK: CLKSRC: Add suspend resume hooks
ARM: AM43XX: Add functions to save/restore am43xx control registers
ASoC: ams_delta: use GPIO lookup table
ARM: OMAP1: ams-delta: add GPIO lookup tables
bus: ti-sysc: Fix optional clocks array access
ARM: OMAP2+: Make sure LOGICRETSTATE bits are not cleared
ARM: OMAP2+: prm44xx: Inroduce cpu_pm notifiers for context save/restore
ARM: OMAP2+: prm44xx: Introduce context save/restore for am43 PRCM IO
ARM: OMAP2+: powerdomain: Introduce cpu_pm notifiers for context save/restore
...
* SoC
- Change platform dependency to ARCH_RENESAS
Geert Uytterhoeven says "The Renesas Fine Display Processor driver is
used on Renesas R-Car SoCs only. Since commit 9b5ba0df4e ("ARM:
shmobile: Introduce ARCH_RENESAS") is ARCH_RENESAS a more appropriate
platform dependency than the legacy ARCH_SHMOBILE, hence use the
former.
This will allow to drop ARCH_SHMOBILE on ARM and ARM64 in the near
future."
- Add the to Kconfig RZ/N1D (r9a06g032) SoC
In preparation for upstream support of this SoC
- Identify R-Car E3 (r8a77990) SoC
- Identify and add minimal support for RZ/G1C (r8a77470) SoC
* R-Car SYSC
- Add support for R-Car E3 (r8a77990) SoC
Shimoda-san says this adds:
+ "Cortex-A53 CPU{0,1}, Cortex-A53 SCU, Cortex-R7, A3VC,
A2VC1 and 3DG-{A,B} power domain areas..."
+ "workaround for 3DG-{A,B} of R-Car E3 ES1.0 because
the SoC has a restriction about the order."
- Remove unused inclusion of <linux/sys_soc.h>,
- Make r8a77995_areas[] const.
* R-Car Reset
- Add support for R-Car E3 (r8a77990) SoC
This driver is needed for the clock driver to work
* Debug-LL
- Add support for RZ/G1C (r8a77470) SoC
RZ/G1C uses SCIF1 for the debug console
-----BEGIN PGP SIGNATURE-----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=xLPA
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Renesas ARM Based SoC Updates for v4.18
* SoC
- Change platform dependency to ARCH_RENESAS
This will allow to drop ARCH_SHMOBILE on ARM and ARM64 in the near
future.
- Add the to Kconfig RZ/N1D (r9a06g032) SoC
- Identify R-Car E3 (r8a77990) SoC
- Identify and add minimal support for RZ/G1C (r8a77470) SoC
* R-Car SYSC
- Add support for R-Car E3 (r8a77990) SoC
- Remove unused inclusion of <linux/sys_soc.h>,
- Make r8a77995_areas[] const.
* R-Car Reset
- Add support for R-Car E3 (r8a77990) SoC
* Debug-LL
- Add support for RZ/G1C (r8a77470) SoC
* tag 'renesas-soc-for-v4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
soc: renesas: r8a77990-sysc: Add workaround for 3DG-{A,B}
soc: renesas: rcar-sysc: Add support for R-Car E3 power areas
arm: shmobile: Add the RZ/N1D (R9A06G032) to the shmobile Kconfig
arm: shmobile: Change platform dependency to ARCH_RENESAS
soc: renesas: r8a77995-sysc: Cleanups
soc: renesas: rcar-rst: Add support for R-Car E3
soc: renesas: Add r8a77990 SYSC PM Domain Binding Definitions
soc: renesas: identify R-Car E3
ARM: debug-ll: Add support for r8a77470
ARM: shmobile: Add the RZ/N1 arch to the shmobile Kconfig
ARM: shmobile: r8a77470: basic SoC support
soc: renesas: rcar-sysc: Add r8a77470 support
soc: renesas: rcar-rst: Add support for RZ/G1C
soc: renesas: Identify RZ/G1C
Signed-off-by: Olof Johansson <olof@lixom.net>
Define this symbol if the architecture either uses 64-bit pointers or the
PHYS_ADDR_T_64BIT is set. This covers 95% of the old arch magic. We only
need an additional select for Xen on ARM (why anyway?), and we now always
set ARCH_DMA_ADDR_T_64BIT on mips boards with 64-bit physical addressing
instead of only doing it when highmem is set.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: James Hogan <jhogan@kernel.org>
Now that a common function is available for CNTVOFF's
initialization, let's convert shmobile-apmu code to use
this function.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the RZ/N1D SoC to the reset of the Renesas SoC Collection.
Signed-off-by: Michel Pollet <michel.pollet@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the RZ/N1 Family (Part #R9A06G0xx) ARCH config to the rest of
the Renesas SoC collection.
Signed-off-by: Michel Pollet <michel.pollet@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add minimal support for the RZ/G1C (R8A77470) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds watchdog support by installing shmobile_boot_vector_gen2
to ICRAM1 when enough memory is available, in which case we also keep a
copy of MPIDR to complete the reset vector logic.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On R-Car Gen2 and RZ/G1 platforms, we use the SBAR registers to make non
boot CPUs run a routine designed to bring up SMP and deal with hot plug.
The value contained in the SBAR registers is not initialized by a WDT
triggered reset, which means that after a WDT triggered reset we jump
to the SMP bring up routine, preventing the system from executing the
bootrom code.
The purpose of this patch is to jump to the bootrom code in case of a
WDT triggered reset, and keep the SMP functionality untouched.
In order to tell if the code had been called due to the WDT overflowing
we are testing WOVF from register RWTCSRA.
The new function shmobile_boot_vector_gen2 isn't replacing
shmobile_boot_vector for backward compatibility reasons. The kernel
will install the best option (either shmobile_boot_vector or
shmobile_boot_vector_gen2) to ICRAM1 after parsing the device tree,
according to the amount of memory available.
Since shmobile_boot_vector has become bigger, "reg" property of nodes
compatible with "renesas,smp-sram" now need to be set to a value
greater or equal to "<0 0x60>".
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: dropped #ifdef from common.h]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On systems with two regulators, a bogus error message is printed on
success:
i2c 6-0058: i2c error 2
While adding support for Stout, the number of messages to send was
made variable, but the corresponding return value check of
i2c_transfer() wasn't updated.
Fixes: ff938cd14d ("ARM: shmobile: stout: enable R-Car Gen2 regulator quirk")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Regulator setup is suboptimal on H2 Stout too. The Stout newly has
two DA9210 regulators, so the quirk is extended to handle another
DA9210 at i2c address 0x70.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are
OMAP, Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now
with a Quad-Core ARM Cortex-A7. According to the manufacturer,
it is intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family
of chips meant for managed gigabit ethernet switches, based
around a Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2
and Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jlJ2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are OMAP,
Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now with a
Quad-Core ARM Cortex-A7. According to the manufacturer, it is
intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of
chips meant for managed gigabit ethernet switches, based around a
Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2 and
Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module
ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER
arm64: defconfig: enable CONFIG_GPIO_UNIPHIER
ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b
ARM: meson: Add SMP bringup code for Meson8 and Meson8b
ARM: smp_scu: allow the platform code to read the SCU CPU status
ARM: smp_scu: add a helper for powering on a specific CPU
dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation
ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init()
ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init()
ARM: defconfig: select the right SX150X driver
arm64: defconfig: Enable QCOM_IOMMU
arm64: Add ThunderX drivers to defconfig
arm64: defconfig: Enable Tegra PCI controller
cpufreq: imx6q: Move speed grading check to cpufreq driver
arm64: defconfig: re-enable Qualcomm DB410c USB
ARM: configs: stm32: Add MDMA support in STM32 defconfig
ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
...
* pm-domains:
PM / Domains: Fix genpd to deal with drivers returning 1 from ->prepare()
PM / domains: Rework governor code to be more consistent
PM / Domains: Remove gpd_dev_ops.active_wakeup() callback
soc: rockchip: power-domain: Use GENPD_FLAG_ACTIVE_WAKEUP
soc: mediatek: Use GENPD_FLAG_ACTIVE_WAKEUP
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ACTIVE_WAKEUP
PM / Domains: Allow genpd users to specify default active wakeup behavior
PM / Domains: Add support to select performance-state of domains
PM / Domains: Rename genpd internals from pm_genpd_* to genpd_*
Set the newly introduced GENPD_FLAG_ACTIVE_WAKEUP, which allows to
remove the driver's own "always true" callback.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bugfix for the SMP case broke the build for the UP case:
arch/arm/mach-shmobile/headsmp-apmu.o: In function `shmobile_boot_apmu':
(.text+0x34): undefined reference to `secondary_startup'
The assembler file mixes code that is used for SMP with code
that we also need on a single-CPU build, so I'm leaving it
always enabled in the Makefile, but enclose the SMP code
in an #ifdef.
Fixes: fd45a136ff6 ("ARM: shmobile: rcar-gen2: Make sure CNTVOFF is initialized on CA7/15")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On Cortex-A7, the arch timer CNTVOFF register is uninitialized.
Ideally it should be initialized by the boot loader, but it isn't.
For the boot CPU, CNTVOFF is initialized by Linux since commit
9ce3fa6816 ("ARM: shmobile: rcar-gen2: Add CA7 arch_timer
initialization for r8a7794").
For secondary CPU cores, no such initialization is done.
Hence when enabling SMP on r8a7794, the kernel log is spammed with:
WARNING: Underflow in clocksource 'arch_sys_counter' observed, time update ignored.
Please report this, consider using a different clocksource, if possible.
Your kernel is probably still fine.
As Marc Zyngier pointed out that Cortex-A15 and Cortex-A7 are similar with
respect to CNTVOFF, we have been very lucky this just worked on R-Car
Gen2 SoCs with Cortex-A15 cores.
To fix this:
- Move the existing inline asm code to initialize CNTVOFF to an
assembler source file (adding comments and replacing hardcoded
constants by definitions in the process), so it can be reused,
- Perform the initialization of CNTVOFF on the boot CPU (Cortex-A15 or
Cortex-A7) on all R-Car Gen2 and RZ/G1 parts,
- Wrap the standard secondary_startup() routine inside a routine which
initializes CNTVOFF.
Based on patches by Hisashi Nakamura in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Add debug-ll support to RZ/G1M (r8a7743) SoC
Chris Paterson says, "RZ/G1M uses SCIF0 for the debug console, like most
of the R-Car Gen2 SoCs."
* Remove ARCH_SHMOBILE_MULTI
Geert Uytterhoeven says, "The migration from ARCH_SHMOBILE_MULTI to
ARCH_RENESAS has been completed in v4.12..."
* Correct arch timer frequency on RZ/G1M (r8a7743) SoC
Geert Uytterhoeven says, "According to the datasheet, the frequency of
the ARM architecture timer on RZ/G1E depends on the frequency of the ZS
clock..."
* Add support for CPG/MSSR bindings
Geert Uytterhoeven says, "When using the new CPG/MSSR bindings, there is
no longer a "renesas,rcar-gen2-cpg-clocks" node, and the code to obtain
the external clock crystal frequency falls back to a default of 20 MHz.
While this is correct for all upstream R-Car Gen2 and RZ/G1 boards, this
is not necessarily the case for out-of-tree third party boards.
Add support for finding the external clock crystal oscillator on RZ/G1M,
and on R-Car H2, M2-W, and M2-N using the new CPG/MSSR bindings, through
the corresponding "renesas,r8a77xx-cpg-mssr" nodes."
* Obtain jump stub region from DT
Geert Uytterhoeven says, "Add support for obtaining from DT the SRAM
region to store the jump stub for CPU core bringup, according to the
renesas,smp-sram DT bindings."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZf0J3AAoJENfPZGlqN0++GfAP/21nuyREfKfOBV2B3DOAXVWS
VhqOSgOaK/oAVfIfk7dSrk+ZqRF0fgF14EDQyzaNgi/coPb0cL2Xt8fpbYIp/H1/
BBjJg/Q+XptMRWGbh4oshgO2W4wNCXyPJRQ/x7ciDFkygJqgmbu0sF1CF6spis/K
n3sDS4w/bJVOnTZhOG6v0U0p80X0nc0W4M8fQPZjhecBjPCXGmqOekH7Tm9HmJgu
HktXX8OsngGMfI9NUPQcl8KgPWNfBi4U0X4Ep5cTGutJ25WsQiW4LDoSFFrF1JIY
Kll985IvAgLfAOEeezrua+/cM1FsOOZBQyXmV9awBmLEmzicyxOr7Lp1eK3RfADw
RQ2foFnUYakMfJcnVVjZD8tNg+eNafN0VjSwbvlvQH+1P+vy5EvUKovjyed7u9n9
TIuewlrrJdMAMx2wwFEeotzU3JjZB0rIJb0hzy9zk/qekC0II4O25Y1gH16tfYJa
65UC172dQmjt3mP7aK88V0bJX5NNKU7/1YALHplih3qRuqov2CgCUtdEdzqHJgYh
C4Thd1ejdFTgWSqaBUInQfBs3lNDO1JfwfdVCmLq7tG8jEpV/zZTeywxqizMEIsH
6f/cd7oTkIbZ9i2UVOMnhWQhyGIkOJD+/ylr4D7iqhL0yC7/mCcalHR8FsNps81J
qA4Hy70ALb/D8A9PMjgE
=PJul
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Renesas ARM Based SoC Updates for v4.14" Simon Horman:
* Add debug-ll support to RZ/G1M (r8a7743) SoC
Chris Paterson says, "RZ/G1M uses SCIF0 for the debug console, like most
of the R-Car Gen2 SoCs."
* Remove ARCH_SHMOBILE_MULTI
Geert Uytterhoeven says, "The migration from ARCH_SHMOBILE_MULTI to
ARCH_RENESAS has been completed in v4.12..."
* Correct arch timer frequency on RZ/G1M (r8a7743) SoC
Geert Uytterhoeven says, "According to the datasheet, the frequency of
the ARM architecture timer on RZ/G1E depends on the frequency of the ZS
clock..."
* Add support for CPG/MSSR bindings
Geert Uytterhoeven says, "When using the new CPG/MSSR bindings, there is
no longer a "renesas,rcar-gen2-cpg-clocks" node, and the code to obtain
the external clock crystal frequency falls back to a default of 20 MHz.
While this is correct for all upstream R-Car Gen2 and RZ/G1 boards, this
is not necessarily the case for out-of-tree third party boards.
Add support for finding the external clock crystal oscillator on RZ/G1M,
and on R-Car H2, M2-W, and M2-N using the new CPG/MSSR bindings, through
the corresponding "renesas,r8a77xx-cpg-mssr" nodes."
* Obtain jump stub region from DT
Geert Uytterhoeven says, "Add support for obtaining from DT the SRAM
region to store the jump stub for CPU core bringup, according to the
renesas,smp-sram DT bindings."
* tag 'renesas-soc-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove ARCH_SHMOBILE_MULTI
ARM: shmobile: rcar-gen2: Correct arch timer frequency on RZ/G1E
ARM: shmobile: rcar-gen2: Add support for CPG/MSSR bindings
ARM: shmobile: rcar-gen2: Obtain jump stub region from DT
ARM: debug-ll: Add support for r8a7743
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix deadlock in regulator quirk for R-Car Gen 2 SoCs
The da9063/da9210 regulator quirk for R-Car Gen2 boards uses a bus
notifier, and unregisters the notifier when it is no longer needed.
However, a notifier must not be unregistered from within the call chain.
This bug went unnoticed, as blocking_notifier_chain_unregister() didn't
take the semaphore during early boot. This is no longer the case as of
upstream commit 1c3c5eab17 ("sched/core: Enable might_sleep() and
smp_processor_id() checks early") and a deadlock occurs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=N5ig
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes3-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Third Round of Renesas ARM Based SoC Fixes for v4.13" from Simon Horman:
Fix deadlock in regulator quirk for R-Car Gen 2 SoCs
The da9063/da9210 regulator quirk for R-Car Gen2 boards uses a bus
notifier, and unregisters the notifier when it is no longer needed.
However, a notifier must not be unregistered from within the call chain.
This bug went unnoticed, as blocking_notifier_chain_unregister() didn't
take the semaphore during early boot. This is no longer the case as of
upstream commit 1c3c5eab17 ("sched/core: Enable might_sleep() and
smp_processor_id() checks early") and a deadlock occurs.
* tag 'renesas-fixes3-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: rcar-gen2: Fix deadlock in regulator quirk
Simon Horman reported that Koelsch and Lager hang during boot, and
bisected this to commit 1c3c5eab17 ("sched/core: Enable
might_sleep() and smp_processor_id() checks early").
The da9063/da9210 regulator quirk for R-Car Gen2 boards uses a bus
notifier, and unregisters the notifier when it is no longer needed.
However, a notifier must not be unregistered from within the call chain.
This bug went unnoticed, as blocking_notifier_chain_unregister() didn't
take the semaphore during early boot. The aforementioned commit changed
that behavior, leading to a deadlock.
Fix this by removing the call to bus_unregister_notifier(), and keeping
local completion state instead.
Reported-by: Simon Horman <horms+renesas@verge.net.au>
Fixes: 663fbb5215 ("ARM: shmobile: R-Car Gen2: Add da9063/da9210 regulator quirk")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The migration from ARCH_SHMOBILE_MULTI to ARCH_RENESAS has been
completed in v4.12 by commit 9ed2d4bc5c ("ARM: dts: renesas:
Switch from ARCH_SHMOBILE_MULTI to ARCH_RENESAS"), so the
ARCH_SHMOBILE_MULTI symbol can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to the datasheet, the frequency of the ARM architecture timer
on RZ/G1E depends on the frequency of the ZS clock, just like on R-Car
E2 and V2H.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When using the new CPG/MSSR bindings, there is no longer a
"renesas,rcar-gen2-cpg-clocks" node, and the code to obtain the external
clock crystal frequency falls back to a default of 20 MHz.
While this is correct for all upstream R-Car Gen2 and RZ/G1 boards, this
is not necessarily the case for out-of-tree third party boards.
Add support for finding the external clock crystal oscillator on RZ/G1M,
and on R-Car H2, M2-W, and M2-N using the new CPG/MSSR bindings, through
the corresponding "renesas,r8a77xx-cpg-mssr" nodes.
Note that this is not needed on R-Car V2H and E2, and on RZ/G1E, as on
those SoCs the arch_timer and generic counter clock is derived from the
ZS clock instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for obtaining from DT the SRAM region to store the jump stub
for CPU core bringup, according to the renesas,smp-sram DT bindings.
If no region is specified in DT, the code falls back to hardcoded ICRAM1
as before, to maintain backwards compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SoC platform changes (arch/arm/mach-*). This merge window, the bulk is
for a few platforms:
- Andres Färber adds initial support for the Actions Semi S500 (a.k.a.
'owl') platform, a close relative of the S900 platform he adds for arm64.
- in mach-omap2, we remove more legacy code
- Rockchips gains support for the RV1108 SoC designed for camera
applications.
- For Atmel, we gain support for MMU-less SoCs (SAME70/V71/S70/V70)
- Minor updates for other platforms, including davinci, s3c64xx,
prima2, stm32, broadcom nsp, amlogic, pxa, imx and renesas
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8F3w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"SoC platform changes (arch/arm/mach-*). This merge window, the bulk is
for a few platforms:
- Andres Färber adds initial support for the Actions Semi S500 (aka
'owl') platform, a close relative of the S900 platform he adds for
arm64.
- in mach-omap2, we remove more legacy code
- Rockchips gains support for the RV1108 SoC designed for camera
applications.
- For Atmel, we gain support for MMU-less SoCs (SAME70/V71/S70/V70)
- Minor updates for other platforms, including davinci, s3c64xx,
prima2, stm32, broadcom nsp, amlogic, pxa, imx and renesas"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (74 commits)
ARM: owl: smp: Drop bogus holding pen
ARM: owl: Drop custom machine
ARM: owl: smp: Implement SPS power-gating for CPU2 and CPU3
soc: actions: owl-sps: Factor out owl_sps_set_pg() for power-gating
soc: actions: Add Owl SPS
dt-bindings: power: Add Owl SPS power domains
MAINTAINERS: Update Actions Semi section with SPS
ARM: owl: Implement CPU enable-method for S500
MAINTAINERS: Add Actions Semi Owl section
ARM: Prepare Actions Semi S500
ARM: socfpga: Increase max number of GPIOs
ARM: stm32: Introduce MACH_STM32F469 flag
ARM: prima2: remove redundant select CPU_V7
ARM: davinci: fix const warnings
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ALWAYS_ON
ARM: OMAP4: hwmod_data: add SHAM crypto accelerator
ARM: OMAP4: hwmod data: add des
ARM: OMAP4: hwmod data: add aes2
ARM: OMAP4: hwmod data: add aes1
ARM: pxa: Delete an error message for a failed memory allocation in pxa3xx_u2d_probe()
...
The function name is now renamed to 'timer_probe' for consistency with
the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Improve handling of always-on PM domains by using the
GENPD_FLAG_ALWAYS_ON flag introduced in commit ffaa42e8a4 ("PM /
Domains: Enable users of genpd to specify always on PM domains").
Note that the PM domain containing the serial console is still handled
locally.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Even though L2C is specified in the DT, you still need to add the aux
settings in the machine_desc.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Pull ARM updates from Russell King:
- nommu updates from Afzal Mohammed cleaning up the vectors support
- allow DMA memory "mapping" for nommu Benjamin Gaignard
- fixing a correctness issue with R_ARM_PREL31 relocations in the
module linker
- add strlen() prototype for the decompressor
- support for DEBUG_VIRTUAL from Florian Fainelli
- adjusting memory bounds after memory reservations have been
registered
- unipher cache handling updates from Masahiro Yamada
- initrd and Thumb Kconfig cleanups
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (23 commits)
ARM: mm: round the initrd reservation to page boundaries
ARM: mm: clean up initrd initialisation
ARM: mm: move initrd init code out of arm_memblock_init()
ARM: 8655/1: improve NOMMU definition of pgprot_*()
ARM: 8654/1: decompressor: add strlen prototype
ARM: 8652/1: cache-uniphier: clean up active way setup code
ARM: 8651/1: cache-uniphier: include <linux/errno.h> instead of <linux/types.h>
ARM: 8650/1: module: handle negative R_ARM_PREL31 addends correctly
ARM: 8649/2: nommu: remove Hivecs configuration is asm
ARM: 8648/2: nommu: display vectors base
ARM: 8647/2: nommu: dynamic exception base address setting
ARM: 8646/1: mmu: decouple VECTORS_BASE from Kconfig
ARM: 8644/1: Reduce "CPU: shutdown" message to debug level
ARM: 8641/1: treewide: Replace uses of virt_to_phys with __pa_symbol
ARM: 8640/1: Add support for CONFIG_DEBUG_VIRTUAL
ARM: 8639/1: Define KERNEL_START and KERNEL_END
ARM: 8638/1: mtd: lart: Rename partition defines to be prefixed with PART_
ARM: 8637/1: Adjust memory boundaries after reservations
ARM: 8636/1: Cleanup sanity_check_meminfo
ARM: add CPU_THUMB_CAPABLE to indicate possible Thumb support
...
All low-level PM/SMP code using virt_to_phys() should actually use
__pa_symbol() against kernel symbols. Update code where relevant to move
away from virt_to_phys().
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the SoC branch we normally collect classic arch/arm/mach-* contents, i.e.
C code changes for SoC platforms. This release cycle the diffstat is quite
nice, in that we're removing 3x the amount of code that's being added.
The main reason for this is that there's a removal of camera drivers for
Freescale i.MX chips (driver was removed so the device registration isn't
needed any more). There's also removal of display initialization code for OMAP
that is no longer needed.
The rest are mostly minor tweaks and cleanups; constification on Samsung
platforms, cleanup of ux500 platform data, purge of other unused platform
data/device seutp on i.MX and other good stuff.
New SoC support this cycle is for two Allwinner platforms, H2+ and V3s.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YE8v
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"In the SoC branch we normally collect classic arch/arm/mach-*
contents, i.e. C code changes for SoC platforms. This release cycle
the diffstat is quite nice, in that we're removing 3x the amount of
code that's being added.
The main reason for this is that there's a removal of camera drivers
for Freescale i.MX chips (driver was removed so the device
registration isn't needed any more). There's also removal of display
initialization code for OMAP that is no longer needed.
The rest are mostly minor tweaks and cleanups; constification on
Samsung platforms, cleanup of ux500 platform data, purge of other
unused platform data/device seutp on i.MX and other good stuff.
New SoC support this cycle is for two Allwinner platforms, H2+ and
V3s"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (55 commits)
ARM: ux500: remove deleted file from Makefile
ARM: ep93xx: Disable TS-72xx watchdog before uncompressing
ARM: ux500: cut some platform data
MAINTAINERS: Update for the current location of the bcm2835 tree.
ARM: davinci: remove BUG_ON() from da850_register_sata()
ARM: davinci: da850: model the SATA refclk
ARM: davinci: da850: add con_id for the SATA clock
ARM: davinci: da8xx-dt: add OF_DEV_AUXDATA entry for SATA
arm: mvebu: support for SMP on 98DX3336 SoC
dt-bindings: video: exynos7-decon: Remove obsolete samsung,power-domain property
soc: dove: constify reset_control_ops structures
ARM: mv78xx0: fix possible PCI buffer overflow
MAINTAINERS: transfer maintainership for the EZX platform
ARM: shmobile: rcar-gen2: Add more register documentation
ARM: tegra: paz00: Fix __initdata placement
ARM: OMAP: clock: Remove unused mpurate cmdline option
ARM: davinci: add skeleton for pdata-quirks
arm: sunxi: add support for V3s SoC
ARM: OMAP2+: omap_hwmod: Add support for earlycon
arm: hisi: drop extern hip01_cpu_die
...
This patch adds a OSTM driver for the Renesas architecture.
The OS Timer (OSTM) has independent channels that can be
used as a freerun or interval times.
This driver uses the first probed device as a clocksource
and then any additional devices as clock events.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Geert Uytterhoeven