All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm/boot/dts/sun?i*.*
arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we can handle the generic pinctrl bindings, convert our DT to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The allwinner,pull property set to NO_PULL was really considered our
default (and wasn't even changing the default value in the code).
Remove these properties to make it obvious that we do not set anything in
such a case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add pmic / regulator nodes to Mele A1000G quad dts.
Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
marked as regulator-always-on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The blue led on the Mele A1000 is wired to light up as soon as the board
has powered (it will be on while the gpio is still in input / floating
mode), also its location on the top-set box clearly signals "power led".
Until now we've been treating this as a generic usr function led, which
means that when you plug power into the top-set box, the power-led lights
and then turns off as soon as the kernel loads, which looks wrong.
This renames the led from m9:blue:usr to a1000g:blue:pwr (fixing a copy
and paste error in the prefix while at it) and marks it as default on,
fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The Mele A1000G-quad has an usb to sata bridge connected to its otg
controller, this commit enables support for this. Since the otg is
hardwired to the sata bridge it gets enabled in host only mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele A1000G-quad and the Mele M9 have the same PCB, sofar we've been using
the same dts for both models. Unfortunately this does not work for the otg
controller, on the M9 this is routed to a micro-usb connector on the outside,
while as on the A1000G-quad it is connected to an usb to sata bridge
(which is not populated on the M9 pcb).
This commit adds a new dts for the Mele-A1000G-quad to allow using
different otg controller settings on the 2 boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai