Noidle should be the default for writes as seen by all the compounds
definitions in fs.h using it. In fact only direct I/O really should
be using NODILE, so turn the whole flag around to get the defaults
right, which will make our life much easier especially onces the
WRITE_* defines go away.
This assumes all the existing "raw" users of REQ_SYNC for writes
want noidle behavior, which seems to be spot on from a quick audit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The local variable "err" will be set to an appropriate value
by a following statement.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Multiplications for the size determination of memory allocations
indicated that array data structures should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A lot of the REQ_* flags are only used on struct requests, and only of
use to the block layer and a few drivers that dig into struct request
internals.
This patch adds a new req_flags_t rq_flags field to struct request for
them, and thus dramatically shrinks the number of common requests. It
also removes the unfortunate situation where we have to fit the fields
from the same enum into 32 bits for struct bio and 64 bits for
struct request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It makes the message hard to interpret correctly if a base 10 number is
prefixed by 0x. So change to a hex number.
Link: http://lkml.kernel.org/r/20161026125658.25728-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Discontinue having the brd driver destructively free all pages in the
ramdisk in response to the BLKFLSBUF ioctl. Doing so allows a BLKFLSBUF
ioctl issued to a logical partition to destroy pages of the parent brd
device (and all other partitions of that brd device).
This change breaks compatibility - but in this case the compatibility
breaks more than it helps.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently rd_size was int which lead to overflow and bogus device size
once the requested ramdisk size was 1 TB or more. Although these days
ramdisks with 1 TB size are mostly a mistake, the days when they are
useful are not far.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 0eadf37afc ("nbd: allow block mq to deal with timeouts")
changed normal usage of nbd->sock_lock to use spin_lock/spin_unlock
rather than the *_irq variants, but it missed this unlock in an
error path.
Found by Coverity, CID 1373871.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Fixes: 0eadf37afc ("nbd: allow block mq to deal with timeouts")
Signed-off-by: Jens Axboe <axboe@fb.com>
If the header object gets deleted (perhaps along with the entire pool),
there is no point in attempting to reregister the watch. Treat this
the same as blacklisting: fail all pending and new I/Os requiring the
lock.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
-EBLACKLISTED from __rbd_register_watch() means that our ceph_client
got blacklisted - we won't be able to restore the watch and reacquire
the lock. Wake up and fail all outstanding requests waiting for the
lock and arrange for all new requests that require the lock to fail
immediately.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Tested-by: Mike Christie <mchristi@redhat.com>
A good practice is to prefix the names of functions by the name
of the subsystem.
The kthread worker API is a mix of classic kthreads and workqueues. Each
worker has a dedicated kthread. It runs a generic function that process
queued works. It is implemented as part of the kthread subsystem.
This patch renames the existing kthread worker API to use
the corresponding name from the workqueues API prefixed by
kthread_:
__init_kthread_worker() -> __kthread_init_worker()
init_kthread_worker() -> kthread_init_worker()
init_kthread_work() -> kthread_init_work()
insert_kthread_work() -> kthread_insert_work()
queue_kthread_work() -> kthread_queue_work()
flush_kthread_work() -> kthread_flush_work()
flush_kthread_worker() -> kthread_flush_worker()
Note that the names of DEFINE_KTHREAD_WORK*() macros stay
as they are. It is common that the "DEFINE_" prefix has
precedence over the subsystem names.
Note that INIT() macros and init() functions use different
naming scheme. There is no good solution. There are several
reasons for this solution:
+ "init" in the function names stands for the verb "initialize"
aka "initialize worker". While "INIT" in the macro names
stands for the noun "INITIALIZER" aka "worker initializer".
+ INIT() macros are used only in DEFINE() macros
+ init() functions are used close to the other kthread()
functions. It looks much better if all the functions
use the same scheme.
+ There will be also kthread_destroy_worker() that will
be used close to kthread_cancel_work(). It is related
to the init() function. Again it looks better if all
functions use the same naming scheme.
+ there are several precedents for such init() function
names, e.g. amd_iommu_init_device(), free_area_init_node(),
jump_label_init_type(), regmap_init_mmio_clk(),
+ It is not an argument but it was inconsistent even before.
[arnd@arndb.de: fix linux-next merge conflict]
Link: http://lkml.kernel.org/r/20160908135724.1311726-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1470754545-17632-3-git-send-email-pmladek@suse.com
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
with maintenance operations offloaded to userspace (Douglas Fuller,
Mike Christie and myself). Another block device bullet is a series
fixing up layering error paths (myself).
On the filesystem side, we've got patches that improve our handling of
buffered vs dio write races (Neil Brown) and a few assorted fixes from
Zheng. Also included a couple of random cleanups and a minor CRUSH
update.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJX+PjZAAoJEEp/3jgCEfOLVuoH/RwtFLIb6/KZUYtBOrVVrTun
kReRlfq2xKYrGGtyQEqSuz7fBdwT1LVCVcL8kC4GFD4R67o+tNMAr6PfM/7pZABj
HRoRLgSZ9FLw4W5n0VpBIznih75QUbCdXiTCtH9eorMHU5q1YpTvVHHlF9W9Pm2I
eNGnBWpGyHVeiK66mpUCH+EQKQ4GkAVD9rneTNqLHgq2yotHkVl1j258+DL6JRGs
OBoh3RmNQaGOAS37Lss8erCSusAGEcAeGV6ubuK2lFUKyR41EkD3I0xkhNSPe+CD
RifFcpVziIeTu//cLgl0nnHGtmUytD7HgJubaPthArKIOen9ZDAfEkgI0o+JI2A=
=45O7
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-4.9-rc1' of git://github.com/ceph/ceph-client
Pull Ceph updates from Ilya Dryomov:
"The big ticket item here is support for rbd exclusive-lock feature,
with maintenance operations offloaded to userspace (Douglas Fuller,
Mike Christie and myself). Another block device bullet is a series
fixing up layering error paths (myself).
On the filesystem side, we've got patches that improve our handling of
buffered vs dio write races (Neil Brown) and a few assorted fixes from
Zheng. Also included a couple of random cleanups and a minor CRUSH
update"
* tag 'ceph-for-4.9-rc1' of git://github.com/ceph/ceph-client: (39 commits)
crush: remove redundant local variable
crush: don't normalize input of crush_ln iteratively
libceph: ceph_build_auth() doesn't need ceph_auth_build_hello()
libceph: use CEPH_AUTH_UNKNOWN in ceph_auth_build_hello()
ceph: fix description for rsize and rasize mount options
rbd: use kmalloc_array() in rbd_header_from_disk()
ceph: use list_move instead of list_del/list_add
ceph: handle CEPH_SESSION_REJECT message
ceph: avoid accessing / when mounting a subpath
ceph: fix mandatory flock check
ceph: remove warning when ceph_releasepage() is called on dirty page
ceph: ignore error from invalidate_inode_pages2_range() in direct write
ceph: fix error handling of start_read()
rbd: add rbd_obj_request_error() helper
rbd: img_data requests don't own their page array
rbd: don't call rbd_osd_req_format_read() for !img_data requests
rbd: rework rbd_img_obj_exists_submit() error paths
rbd: don't crash or leak on errors in rbd_img_obj_parent_read_full_callback()
rbd: move bumping img_request refcount into rbd_obj_request_submit()
rbd: mark the original request as done if stat request fails
...
Pull blk-mq irq/cpu mapping updates from Jens Axboe:
"This is the block-irq topic branch for 4.9-rc. It's mostly from
Christoph, and it allows drivers to specify their own mappings, and
more importantly, to share the blk-mq mappings with the IRQ affinity
mappings. It's a good step towards making this work better out of the
box"
* 'for-4.9/block-irq' of git://git.kernel.dk/linux-block:
blk_mq: linux/blk-mq.h does not include all the headers it depends on
blk-mq: kill unused blk_mq_create_mq_map()
blk-mq: get rid of the cpumask in struct blk_mq_tags
nvme: remove the post_scan callout
nvme: switch to use pci_alloc_irq_vectors
blk-mq: provide a default queue mapping for PCI device
blk-mq: allow the driver to pass in a queue mapping
blk-mq: remove ->map_queue
blk-mq: only allocate a single mq_map per tag_set
blk-mq: don't redistribute hardware queues on a CPU hotplug event
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Delete the local variable "size" which became unnecessary with
this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Pull setting an error and marking a request done code into a new
helper. obj_request_img_data_test() check isn't strictly needed right
now, but makes it applicable to !img_data requests and a bit safer.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Move the check into rbd_obj_request_destroy() to avoid use-after-free
on errors in rbd_img_request_fill(..., OBJ_REQUEST_PAGES, ...), where
pages, owned by the caller, gets freed in rbd_img_request_fill().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: David Disseldorp <ddiss@suse.de>
Accessing obj_request->img_request union field is only valid for object
requests associated with an image (i.e. if obj_request_img_data_test()
returns true). rbd_osd_req_format_read() used to do more, but now it
just sets osd_req->snap_id. Standalone and stat object requests always
go to the HEAD revision and are fine with CEPH_NOSNAP set by libceph,
so get around the invalid union field use by simply not calling
rbd_osd_req_format_read() in those places.
Reported-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: David Disseldorp <ddiss@suse.de>
- don't put obj_request before rbd_obj_request_get() if
rbd_obj_request_create() fails
- don't leak pages if rbd_obj_request_create() fails
- don't leak stat_request if rbd_osd_req_create() fails
Reported-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: David Disseldorp <ddiss@suse.de>
- fix parent_length == img_request->xferred assert to not fire on
copyup read failures
- don't leak pages if copyup read fails or we can't allocate a new osd
request
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: David Disseldorp <ddiss@suse.de>
Commit 0f2d5be792 ("rbd: use reference counts for image requests")
added rbd_img_request_get(), which rbd_img_request_fill() calls for
each obj_request added to img_request. It was an urgent band-aid for
the uglyness that is rbd_img_obj_callback() and none of the error paths
were updated.
Given that this img_request reference is meant to represent an
obj_request that hasn't passed through rbd_img_obj_callback() yet,
proper cleanup in appropriate destructors is a challenge. However,
noting that if we don't get a chance to call rbd_obj_request_complete(),
there is not going to be a call to rbd_img_obj_callback(), we can move
rbd_img_request_get() into rbd_obj_request_submit() and fixup the two
places that call rbd_obj_request_complete() directly and not through
rbd_obj_request_submit() to temporarily bump img_request, so that
rbd_img_obj_callback() can put as usual.
This takes care of img_request leaks on errors on the submit side.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
If stat request fails with something other than -ENOENT (which just
means that we need to copyup), the original object request is never
marked as done and therefore never completed. Fix this by moving the
mark done + complete snippet from rbd_img_obj_parent_read_full() into
rbd_img_obj_exists_callback(). The former remains covered, as the
latter is its only caller (through rbd_img_obj_request_submit()).
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: David Disseldorp <ddiss@suse.de>
Assert once in rbd_img_obj_request_submit().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: David Disseldorp <ddiss@suse.de>
Add a per-device option to acquire exclusive lock on reads (in addition
to writes and discards). The use case is iSCSI, where it will be used
to prevent execution of stale writes after the implicit failover.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Tested-by: Mike Christie <mchristi@redhat.com>
We take a mutex when sending commands and send stuff over the network, we need
to have queue_rq called asynchronously.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Fixes: fd8383fd88 ("nbd: convert to blkmq")
Signed-off-by: Jens Axboe <axboe@fb.com>
LightNVM compatible device drivers does not have a method to expose
LightNVM specific sysfs entries.
To enable LightNVM sysfs entries to be exposed, lightnvm device
drivers require a struct device to attach it to. To allow both the
actual device driver and lightnvm sysfs entries to coexist, the device
driver tracks the lifetime of the nvm_dev structure.
This patch refactors NVMe and null_blk to handle the lifetime of struct
nvm_dev, which eliminates the need for struct gendisk when a lightnvm
compatible device is provided.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
With LightNVM enabled devices, the gendisk structure is not exposed
to the user. This hides the device driver specific sysfs entries, and
prevents binding of LightNVM geometry information to the device.
Refactor the device registration process, so that gendisk and
non-gendisk devices are easily managed.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
All drivers use the default, so provide an inline version of it. If we
ever need other queue mapping we can add an optional method back,
although supporting will also require major changes to the queue setup
code.
This provides better code generation, and better debugability as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of rolling our own timer, just utilize the blk mq req timeout and do the
disconnect if any of our commands timeout.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In preparation for some future changes, change a few of the state bools over to
normal bits to set/clear properly.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We hit a warning when shutting down the nbd connection because we have irq's
disabled. We don't really need to do the shutdown under the lock, just clear
the nbd->sock. So do the shutdown outside of the irq. This gets rid of the
warning.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This moves NBD over to using blkmq, which allows us to get rid of the NBD
wide queue lock and the async submit kthread. We will start with 1 hw
queue for now, but I plan to add multiple tcp connection support in the
future and we'll fix how we set the hwqueue's.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We get 1 warning when biuld kernel with W=1:
drivers/block/mtip32xx/mtip32xx.c:3689:6: warning: no previous prototype for
'mtip_block_release' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is declared
and don't need a declaration, but can be made static.
so this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
This adds a force close option, so we can force the unmapping
of a rbd device that is open. If a path/device is blacklisted, apps
like multipathd can map a new device and then unmap the old one.
The unmapping cleanup would then be handled by the generic hotunplug
code paths in multipahd like is done for iSCSI, FC/FCOE, SAS, etc.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Export the info used to setup the rbd image, so it can be used to remap
the image.
Signed-off-by: Mike Christie <mchristi@redhat.com>
[idryomov@gmail.com: do_rbd_add() EH]
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Export snap id in sysfs, so tools like multipathd can use it in a uuid.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Export the cluster fsid, so tools like udev and multipath-tools can use
it for part of the uuid.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Export client addr/nonce, so userspace can check if a image is being
blacklisted.
Signed-off-by: Mike Christie <mchristi@redhat.com>
[idryomov@gmail.com: ceph_client_addr(), endianess fix]
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
With exclusive-lock added and more to come, print features into dmesg.
Change capacity to decimal while at it.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Add basic support for RBD_FEATURE_EXCLUSIVE_LOCK feature. Maintenance
operations (resize, snapshot create, etc) are offloaded to librbd via
returning -EOPNOTSUPP - librbd should request the lock and execute the
operation.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Tested-by: Mike Christie <mchristi@redhat.com>
Revamp watch code to support retrying watch re-registration:
- add rbd_dev->watch_state for more robust errcb handling
- store watch cookie separately to avoid dereferencing watch_handle
which is set to NULL on unwatch
- move re-register code into a delayed work and retry re-registration
every second, unless the client is blacklisted
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Tested-by: Mike Christie <mchristi@redhat.com>
This is going to be used for re-registering watch requests and
exclusive-lock tasks: acquire/request lock, notify-acquired, release
lock, notify-released. Some refactoring in the map/unmap paths was
necessary to give this workqueue a meaningful name: "rbdX-tasks".
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
It's gid / global_id in other places.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Current code forgets to free resources in the failure path of
xlvbd_alloc_gendisk(), this patch fix it.
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
blk_mq_update_nr_hw_queues() reset all queue limits to default which it's
not as xen-blkfront expected, introducing blkif_set_queue_limits() to reset
limits with initial correct values.
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Two places didn't get updated when 64KB page granularity was introduced,
this patch fix them.
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
- Misc fixes and cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXq0ruAAoJECgfDbjSjVRp5P8H/2OlDJdSS1l+TwOXbY95ntQ1
vxUX4vGCX5IujC+Rbt7sQV2prE3b6IktFNagpbRoWn21JkpoDMvPtYJrn5BhLtoh
fvDkZE6Wo3QztFSjaUBZWEABBt03KPX0yrAIZplu8ne/Z8KAT3zK57BPnKfmxwv+
dpxt+1wlnqAvYsoUUQZBFT4Gmk2oDiTofiIbQq7W9W/fooznLtLB+ArYtdfNJizC
JnI/vJuWceEXfjT26HexCRhA2OZskrA4ZadDhOjAqkTPN5DHfweLDuHh7IsVfDd1
wXqjc4ks3cYG0CloJ2qY2K7RpDOFIxIizixeDIuAbn9aX4sPOYYfqRm+4iRwmqQ=
=9aUO
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost fixes and cleanups from Michael Tsirkin:
"Misc fixes and cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio/s390: deprecate old transport
virtio/s390: keep early_put_chars
virtio_blk: Fix a slient kernel panic
virtio-vsock: fix include guard typo
vhost/vsock: fix vhost virtio_vsock_pkt use-after-free
9p/trans_virtio: use kvfree() for iov_iter_get_pages_alloc()
virtio: fix error handling for debug builds
virtio: fix memory leak in virtqueue_add()
ceph_file_layout::pool_id is now s64. rbd_add_get_pool_id() and
ceph_pg_poolid_by_name() both return an int, so it's bogus anyway.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
We do a lot of memory allocation in function init_vq, and don't handle
the allocation failure properly. Then this function will return 0,
although initialization fails due to lacking memory. At that moment,
kernel will panic in guest machine, if virtio is used to drive disk.
To fix this bug, we should take care of allocation failure, and return
correct value to let caller know what happen.
Tested-by: Chao Fan <fanc.fnst@cn.fujitsu.com>
Signed-off-by: Minfei Huang <mnghuan@gmail.com>
Signed-off-by: Minfei Huang <minfei.hmf@alibaba-inc.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Purely cosmetic at this point, as rbd doesn't use RADOS namespaces and
hence rbd_dev->header_oloc->pool_ns is always NULL.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Since commit 63a4cc2486, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit abf545484d changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.
Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The rw_page users were not converted to use bio/req ops. As a result
bdev_write_page is not passing down REQ_OP_WRITE and the IOs will
be sent down as reads.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixes: 4e1b2d52a8 ("block, fs, drivers: remove REQ_OP compat defs and related code")
Modified by me to:
1) Drop op_flags passing into ->rw_page(), as we don't use it.
2) Make op_is_write() and friends safe to use for !CONFIG_BLOCK
Signed-off-by: Jens Axboe <axboe@fb.com>
Fix a fat-fingered conversion to the req_op accessors, and also
use a switch statement to make it more obvious what is being checked.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Dave Chinner <david@fromorbit.com>
Fixes: c2df40 ("drivers: use req op accessor");
Reviewed-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Quentin ran into this bug:
WARNING: CPU: 64 PID: 10085 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x65/0x80
sysfs: cannot create duplicate filename '/devices/virtual/block/nbd3/pid'
Modules linked in: nbd
CPU: 64 PID: 10085 Comm: qemu-nbd Tainted: G D 4.6.0+ #7
0000000000000000 ffff8820330bba68 ffffffff814b8791 ffff8820330bbac8
0000000000000000 ffff8820330bbab8 ffffffff810d04ab ffff8820330bbaa8
0000001f00000296 0000000000017681 ffff8810380bf000 ffffffffa0001790
Call Trace:
[<ffffffff814b8791>] dump_stack+0x4d/0x6c
[<ffffffff810d04ab>] __warn+0xdb/0x100
[<ffffffff810d0574>] warn_slowpath_fmt+0x44/0x50
[<ffffffff81218c65>] sysfs_warn_dup+0x65/0x80
[<ffffffff81218a02>] sysfs_add_file_mode_ns+0x172/0x180
[<ffffffff81218a35>] sysfs_create_file_ns+0x25/0x30
[<ffffffff81594a76>] device_create_file+0x36/0x90
[<ffffffffa0000e8d>] __nbd_ioctl+0x32d/0x9b0 [nbd]
[<ffffffff814cc8e8>] ? find_next_bit+0x18/0x20
[<ffffffff810f7c29>] ? select_idle_sibling+0xe9/0x120
[<ffffffff810f6cd7>] ? __enqueue_entity+0x67/0x70
[<ffffffff810f9bf0>] ? enqueue_task_fair+0x630/0xe20
[<ffffffff810efa76>] ? resched_curr+0x36/0x70
[<ffffffff810f0078>] ? check_preempt_curr+0x78/0x90
[<ffffffff810f00a2>] ? ttwu_do_wakeup+0x12/0x80
[<ffffffff810f01b1>] ? ttwu_do_activate.constprop.86+0x61/0x70
[<ffffffff810f0c15>] ? try_to_wake_up+0x185/0x2d0
[<ffffffff810f0d6d>] ? default_wake_function+0xd/0x10
[<ffffffff81105471>] ? autoremove_wake_function+0x11/0x40
[<ffffffffa0001577>] nbd_ioctl+0x67/0x94 [nbd]
[<ffffffff814ac0fd>] blkdev_ioctl+0x14d/0x940
[<ffffffff811b0da2>] ? put_pipe_info+0x22/0x60
[<ffffffff811d96cc>] block_ioctl+0x3c/0x40
[<ffffffff811ba08d>] do_vfs_ioctl+0x8d/0x5e0
[<ffffffff811aa329>] ? ____fput+0x9/0x10
[<ffffffff810e9092>] ? task_work_run+0x72/0x90
[<ffffffff811ba627>] SyS_ioctl+0x47/0x80
[<ffffffff8185f5df>] entry_SYSCALL_64_fastpath+0x17/0x93
---[ end trace 7899b295e4f850c8 ]---
It seems fairly obvious that device_create_file() is not being protected
from being run concurrently on the same nbd.
Quentin found the following relevant commits:
1a2ad21 nbd: add locking to nbd_ioctl
90b8f28 [PATCH] end of methods switch: remove the old ones
d4430d6 [PATCH] beginning of methods conversion
08f8585 [PATCH] move block_device_operations to blkdev.h
It would seem that the race was introduced in the process of moving nbd
from BKL to unlocked ioctls.
By setting nbd->task_recv while the mutex is held, we can prevent other
processes from running concurrently (since nbd->task_recv is also checked
while the mutex is held).
Reported-and-tested-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Pavel Machek <pavel@suse.cz>
Cc: Jens Axboe <axboe@fb.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 09954bad4 ("floppy: refactor open() flags handling"), as a
side-effect, causes open(/dev/fdX, O_ACCMODE) to fail. It turns out that
this is being used setfdprm userspace for ioctl-only open().
Reintroduce back the original behavior wrt !(FMODE_READ|FMODE_WRITE)
modes, while still keeping the original O_NDELAY bug fixed.
Cc: stable@vger.kernel.org # v4.5+
Reported-by: Wim Osterholt <wim@djo.tudelft.nl>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Merge yet more updates from Andrew Morton:
- the rest of ocfs2
- various hotfixes, mainly MM
- quite a bit of misc stuff - drivers, fork, exec, signals, etc.
- printk updates
- firmware
- checkpatch
- nilfs2
- more kexec stuff than usual
- rapidio updates
- w1 things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (111 commits)
ipc: delete "nr_ipc_ns"
kcov: allow more fine-grained coverage instrumentation
init/Kconfig: add clarification for out-of-tree modules
config: add android config fragments
init/Kconfig: ban CONFIG_LOCALVERSION_AUTO with allmodconfig
relay: add global mode support for buffer-only channels
init: allow blacklisting of module_init functions
w1:omap_hdq: fix regression
w1: add helper macro module_w1_family
w1: remove need for ida and use PLATFORM_DEVID_AUTO
rapidio/switches: add driver for IDT gen3 switches
powerpc/fsl_rio: apply changes for RIO spec rev 3
rapidio: modify for rev.3 specification changes
rapidio: change inbound window size type to u64
rapidio/idt_gen2: fix locking warning
rapidio: fix error handling in mbox request/release functions
rapidio/tsi721_dma: advance queue processing from transfer submit call
rapidio/tsi721: add messaging mbox selector parameter
rapidio/tsi721: add PCIe MRRS override parameter
rapidio/tsi721_dma: add channel mask and queue size parameters
...
* RADOS namespace support in libceph and CephFS (Zheng Yan and myself).
The stopgaps added in 4.5 to deny access to inodes in namespaces are
removed and CEPH_FEATURE_FS_FILE_LAYOUT_V2 feature bit is now fully
supported.
* A large rework of the MDS cap flushing code (Zheng Yan).
* Handle some of ->d_revalidate() in RCU mode (Jeff Layton). We were
overly pessimistic before, bailing at the first sight of LOOKUP_RCU.
On top of that we've got a few CephFS bug fixes, a couple of cleanups
and Arnd's workaround for a weird genksyms issue.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJXoKLJAAoJEEp/3jgCEfOLDTUIAIcctpKUiNBokc95mQaXYl34
j7lPIaD0/Ur7JPt4nMdtlywYJYSVV2c+SglHztj/+fv0G4bWbLVEFRruh9SwKIci
PzttcmycIAqSn1f5gBZwyQbGuffd/F0EnBj7fFjcukt01i3s1ZQ7t4XtLGtAV0Ts
aIfFtx9SqWig57Z1OZqNgnhnOoh6IqNbic3FL5Hvdl5N5pFbBcQho6Vzoa5O1osH
URG6RmCcO4nykfSoxiivE7UZ+CImsXHkRD7rupBuIjqjZ8wvmZqQF5qxnkb9Dw2F
IkNhrHkTSIiv4EsNPLAETTnFSozrL1nEykKr2FBW+ti8nxNcav+8FgVapqLvFIw=
=gQ0/
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-4.8-rc1' of git://github.com/ceph/ceph-client
Pull Ceph updates from Ilya Dryomov:
"The highlights are:
- RADOS namespace support in libceph and CephFS (Zheng Yan and
myself). The stopgaps added in 4.5 to deny access to inodes in
namespaces are removed and CEPH_FEATURE_FS_FILE_LAYOUT_V2 feature
bit is now fully supported
- A large rework of the MDS cap flushing code (Zheng Yan)
- Handle some of ->d_revalidate() in RCU mode (Jeff Layton). We were
overly pessimistic before, bailing at the first sight of LOOKUP_RCU
On top of that we've got a few CephFS bug fixes, a couple of cleanups
and Arnd's workaround for a weird genksyms issue"
* tag 'ceph-for-4.8-rc1' of git://github.com/ceph/ceph-client: (34 commits)
ceph: fix symbol versioning for ceph_monc_do_statfs
ceph: Correctly return NXIO errors from ceph_llseek
ceph: Mark the file cache as unreclaimable
ceph: optimize cap flush waiting
ceph: cleanup ceph_flush_snaps()
ceph: kick cap flushes before sending other cap message
ceph: introduce an inode flag to indicates if snapflush is needed
ceph: avoid sending duplicated cap flush message
ceph: unify cap flush and snapcap flush
ceph: use list instead of rbtree to track cap flushes
ceph: update types of some local varibles
ceph: include 'follows' of pending snapflush in cap reconnect message
ceph: update cap reconnect message to version 3
ceph: mount non-default filesystem by name
libceph: fsmap.user subscription support
ceph: handle LOOKUP_RCU in ceph_d_revalidate
ceph: allow dentry_lease_is_valid to work under RCU walk
ceph: clear d_fsinfo pointer under d_lock
ceph: remove ceph_mdsc_lease_release
ceph: don't use ->d_time
...
kernel.h header doesn't directly use dynamic debug, instead we can
include it in module.c (which used it via kernel.h). printk.h only uses
it if CONFIG_DYNAMIC_DEBUG is on, changing the inclusion to only happen
in that case.
Link: http://lkml.kernel.org/r/1468429793-16917-1-git-send-email-luisbg@osg.samsung.com
[luisbg@osg.samsung.com: include dynamic_debug.h in drb_int.h]
Link: http://lkml.kernel.org/r/1468447828-18558-2-git-send-email-luisbg@osg.samsung.com
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1/ Replace pcommit with ADR / directed-flushing:
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement either
ADR, or provide one or more flush addresses per nvdimm. ADR
(Asynchronous DRAM Refresh) flushes data in posted write buffers to the
memory controller on a power-fail event. Flush addresses are defined in
ACPI 6.x as an NVDIMM Firmware Interface Table (NFIT) sub-structure:
"Flush Hint Address Structure". A flush hint is an mmio address that
when written and fenced assures that all previous posted writes
targeting a given dimm have been flushed to media.
2/ On-demand ARS (address range scrub):
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the media
to refresh the bad block list, userspace can also request a re-scrub at
any time.
3/ Support for the Microsoft DSM (device specific method) command format.
4/ Support for EDK2/OVMF virtual disk device memory ranges.
5/ Various fixes and cleanups across the subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xCBG
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
- Replace pcommit with ADR / directed-flushing.
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement
either ADR, or provide one or more flush addresses per nvdimm.
ADR (Asynchronous DRAM Refresh) flushes data in posted write buffers
to the memory controller on a power-fail event.
Flush addresses are defined in ACPI 6.x as an NVDIMM Firmware
Interface Table (NFIT) sub-structure: "Flush Hint Address Structure".
A flush hint is an mmio address that when written and fenced assures
that all previous posted writes targeting a given dimm have been
flushed to media.
- On-demand ARS (address range scrub).
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the
media to refresh the bad block list, userspace can also request a
re-scrub at any time.
- Support for the Microsoft DSM (device specific method) command
format.
- Support for EDK2/OVMF virtual disk device memory ranges.
- Various fixes and cleanups across the subsystem.
* tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (41 commits)
libnvdimm-btt: Delete an unnecessary check before the function call "__nd_device_register"
nfit: do an ARS scrub on hitting a latent media error
nfit: move to nfit/ sub-directory
nfit, libnvdimm: allow an ARS scrub to be triggered on demand
libnvdimm: register nvdimm_bus devices with an nd_bus driver
pmem: clarify a debug print in pmem_clear_poison
x86/insn: remove pcommit
Revert "KVM: x86: add pcommit support"
nfit, tools/testing/nvdimm/: unify shutdown paths
libnvdimm: move ->module to struct nvdimm_bus_descriptor
nfit: cleanup acpi_nfit_init calling convention
nfit: fix _FIT evaluation memory leak + use after free
tools/testing/nvdimm: add manufacturing_{date|location} dimm properties
tools/testing/nvdimm: add virtual ramdisk range
acpi, nfit: treat virtual ramdisk SPA as pmem region
pmem: kill __pmem address space
pmem: kill wmb_pmem()
libnvdimm, pmem: use nvdimm_flush() for namespace I/O writes
fs/dax: remove wmb_pmem()
libnvdimm, pmem: flush posted-write queues on shutdown
...
Pull vfs updates from Al Viro:
"Assorted cleanups and fixes.
Probably the most interesting part long-term is ->d_init() - that will
have a bunch of followups in (at least) ceph and lustre, but we'll
need to sort the barrier-related rules before it can get used for
really non-trivial stuff.
Another fun thing is the merge of ->d_iput() callers (dentry_iput()
and dentry_unlink_inode()) and a bunch of ->d_compare() ones (all
except the one in __d_lookup_lru())"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (26 commits)
fs/dcache.c: avoid soft-lockup in dput()
vfs: new d_init method
vfs: Update lookup_dcache() comment
bdev: get rid of ->bd_inodes
Remove last traces of ->sync_page
new helper: d_same_name()
dentry_cmp(): use lockless_dereference() instead of smp_read_barrier_depends()
vfs: clean up documentation
vfs: document ->d_real()
vfs: merge .d_select_inode() into .d_real()
unify dentry_iput() and dentry_unlink_inode()
binfmt_misc: ->s_root is not going anywhere
drop redundant ->owner initializations
ufs: get rid of redundant checks
orangefs: constify inode_operations
missed comment updates from ->direct_IO() prototype change
file_inode(f)->i_mapping is f->f_mapping
trim fsnotify hooks a bit
9p: new helper - v9fs_parent_fid()
debugfs: ->d_parent is never NULL or negative
...
Add pool namesapce pointer to struct ceph_file_layout and struct
ceph_object_locator. Pool namespace is used by when mapping object
to PG, it's also used when composing OSD request.
The namespace pointer in struct ceph_file_layout is RCU protected.
So libceph can read namespace without taking lock.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
[idryomov@gmail.com: ceph_oloc_destroy(), misc minor changes]
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Define new ceph_file_layout structure and rename old ceph_file_layout
to ceph_file_layout_legacy. This is preparation for adding namespace
to ceph_file_layout structure.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
- ACPI support for guests on ARM platforms.
- Generic steal time support for arm and x86.
- Support cases where kernel cpu is not Xen VCPU number (e.g., if
in-guest kexec is used).
- Use the system workqueue instead of a custom workqueue in various
places.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXmLlrAAoJEFxbo/MsZsTRvRQH/1wOMF8BmlbZfR7H3qwDfjst
ApNifCiZE08xDtWBlwUaBFAQxyflQS9BBiNZDVK0sysIdXeOdpWV7V0ZjRoLL+xr
czsaaGXDcmXxJxApoMDVuT7FeP6rEk6LVAYRoHpVjJjMZGW3BbX1vZaMW4DXl2WM
9YNaF2Lj+rpc1f8iG31nUxwkpmcXFog6ct4tu7HiyCFT3hDkHt/a4ghuBdQItCkd
vqBa1pTpcGtQBhSmWzlylN/PV2+NKcRd+kGiwd09/O/rNzogTMCTTWeHKAtMpPYb
Cu6oSqJtlK5o0vtr0qyLSWEGIoyjE2gE92s0wN3iCzFY1PldqdsxUO622nIj+6o=
=G6q3
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.8-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Features and fixes for 4.8-rc0:
- ACPI support for guests on ARM platforms.
- Generic steal time support for arm and x86.
- Support cases where kernel cpu is not Xen VCPU number (e.g., if
in-guest kexec is used).
- Use the system workqueue instead of a custom workqueue in various
places"
* tag 'for-linus-4.8-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (47 commits)
xen: add static initialization of steal_clock op to xen_time_ops
xen/pvhvm: run xen_vcpu_setup() for the boot CPU
xen/evtchn: use xen_vcpu_id mapping
xen/events: fifo: use xen_vcpu_id mapping
xen/events: use xen_vcpu_id mapping in events_base
x86/xen: use xen_vcpu_id mapping when pointing vcpu_info to shared_info
x86/xen: use xen_vcpu_id mapping for HYPERVISOR_vcpu_op
xen: introduce xen_vcpu_id mapping
x86/acpi: store ACPI ids from MADT for future usage
x86/xen: update cpuid.h from Xen-4.7
xen/evtchn: add IOCTL_EVTCHN_RESTRICT
xen-blkback: really don't leak mode property
xen-blkback: constify instance of "struct attribute_group"
xen-blkfront: prefer xenbus_scanf() over xenbus_gather()
xen-blkback: prefer xenbus_scanf() over xenbus_gather()
xen: support runqueue steal time on xen
arm/xen: add support for vm_assist hypercall
xen: update xen headers
xen-pciback: drop superfluous variables
xen-pciback: short-circuit read path used for merging write values
...
Merge updates from Andrew Morton:
- a few misc bits
- ocfs2
- most(?) of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (125 commits)
thp: fix comments of __pmd_trans_huge_lock()
cgroup: remove unnecessary 0 check from css_from_id()
cgroup: fix idr leak for the first cgroup root
mm: memcontrol: fix documentation for compound parameter
mm: memcontrol: remove BUG_ON in uncharge_list
mm: fix build warnings in <linux/compaction.h>
mm, thp: convert from optimistic swapin collapsing to conservative
mm, thp: fix comment inconsistency for swapin readahead functions
thp: update Documentation/{vm/transhuge,filesystems/proc}.txt
shmem: split huge pages beyond i_size under memory pressure
thp: introduce CONFIG_TRANSPARENT_HUGE_PAGECACHE
khugepaged: add support of collapse for tmpfs/shmem pages
shmem: make shmem_inode_info::lock irq-safe
khugepaged: move up_read(mmap_sem) out of khugepaged_alloc_page()
thp: extract khugepaged from mm/huge_memory.c
shmem, thp: respect MADV_{NO,}HUGEPAGE for file mappings
shmem: add huge pages support
shmem: get_unmapped_area align huge page
shmem: prepare huge= mount option and sysfs knob
mm, rmap: account shmem thp pages
...
We now allocate streams from CPU_UP hot-plug path, there are no
context-dependent stream allocations anymore and we can schedule from
zcomp_strm_alloc(). Use GFP_KERNEL directly and drop a gfp_t parameter.
Link: http://lkml.kernel.org/r/20160531122017.2878-9-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add "deflate", "lz4hc", "842" algorithms to the list of known
compression backends. The real availability of those algorithms,
however, depends on the corresponding CONFIG_CRYPTO_FOO config options.
[sergey.senozhatsky@gmail.com: zram-add-more-compression-algorithms-v3]
Link: http://lkml.kernel.org/r/20160604024902.11778-7-sergey.senozhatsky@gmail.com
Link: http://lkml.kernel.org/r/20160531122017.2878-8-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no way to get a string with all the crypto comp algorithms
supported by the crypto comp engine, so we need to maintain our own
backends list. At the same time we additionally need to use
crypto_has_comp() to make sure that the user has requested a compression
algorithm that is recognized by the crypto comp engine. Relying on
/proc/crypto is not an options here, because it does not show
not-yet-inserted compression modules.
Example:
modprobe zram
cat /proc/crypto | grep -i lz4
modprobe lz4
cat /proc/crypto | grep -i lz4
name : lz4
driver : lz4-generic
module : lz4
So the user can't tell exactly if the lz4 is really supported from
/proc/crypto output, unless someone or something has loaded it.
This patch also adds crypto_has_comp() to zcomp_available_show(). We
store all the compression algorithms names in zcomp's `backends' array,
regardless the CONFIG_CRYPTO_FOO configuration, but show only those that
are also supported by crypto engine. This helps user to know the exact
list of compression algorithms that can be used.
Example:
module lz4 is not loaded yet, but is supported by the crypto
engine. /proc/crypto has no information on this module, while
zram's `comp_algorithm' lists it:
cat /proc/crypto | grep -i lz4
cat /sys/block/zram0/comp_algorithm
[lzo] lz4 deflate lz4hc 842
We still use the `backends' array to determine if the requested
compression backend is known to crypto api. This array, however, may not
contain some entries, therefore as the last step we call crypto_has_comp()
function which attempts to insmod the requested compression algorithm to
determine if crypto api supports it. The advantage of this method is that
now we permit the usage of out-of-tree crypto compression modules
(implementing S/W or H/W compression).
[sergey.senozhatsky@gmail.com: zram-use-crypto-api-to-check-alg-availability-v3]
Link: http://lkml.kernel.org/r/20160604024902.11778-4-sergey.senozhatsky@gmail.com
Link: http://lkml.kernel.org/r/20160531122017.2878-5-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This has started as a 'add zlib support' work, but after some thinking I
saw no blockers for a bigger change -- a switch to crypto API.
We don't have an idle zstreams list anymore and our write path now works
absolutely differently, preventing preemption during compression. This
removes possibilities of read paths preempting writes at wrong places
and opens the door for a move from custom LZO/LZ4 compression backends
implementation to a more generic one, using crypto compress API.
This patch set also eliminates the need of a new context-less crypto API
interface, which was quite hard to sell, so we can move along faster.
benchmarks:
(x86_64, 4GB, zram-perf script)
perf reported run-time fio (max jobs=3). I performed fio test with the
increasing number of parallel jobs (max to 3) on a 3G zram device, using
`static' data and the following crypto comp algorithms:
842, deflate, lz4, lz4hc, lzo
the output was:
- test running time (which can tell us what algorithms performs faster)
and
- zram mm_stat (which tells the compressed memory size, max used memory, etc).
It's just for information. for example, LZ4HC has twice the running
time of LZO, but the compressed memory size is: 23592960 vs 34603008
bytes.
test-fio-zram-842
197.907655282 seconds time elapsed
201.623142884 seconds time elapsed
226.854291345 seconds time elapsed
test-fio-zram-DEFLATE
253.259516155 seconds time elapsed
258.148563401 seconds time elapsed
290.251909365 seconds time elapsed
test-fio-zram-LZ4
27.022598717 seconds time elapsed
29.580522717 seconds time elapsed
33.293463430 seconds time elapsed
test-fio-zram-LZ4HC
56.393954615 seconds time elapsed
74.904659747 seconds time elapsed
101.940998564 seconds time elapsed
test-fio-zram-LZO
28.155948075 seconds time elapsed
30.390036330 seconds time elapsed
34.455773159 seconds time elapsed
zram mm_stat-s (max fio jobs=3)
test-fio-zram-842
mm_stat (jobs1): 3221225472 673185792 690266112 0 690266112 0 0
mm_stat (jobs2): 3221225472 673185792 690266112 0 690266112 0 0
mm_stat (jobs3): 3221225472 673185792 690266112 0 690266112 0 0
test-fio-zram-DEFLATE
mm_stat (jobs1): 3221225472 24379392 37761024 0 37761024 0 0
mm_stat (jobs2): 3221225472 24379392 37761024 0 37761024 0 0
mm_stat (jobs3): 3221225472 24379392 37761024 0 37761024 0 0
test-fio-zram-LZ4
mm_stat (jobs1): 3221225472 23592960 37761024 0 37761024 0 0
mm_stat (jobs2): 3221225472 23592960 37761024 0 37761024 0 0
mm_stat (jobs3): 3221225472 23592960 37761024 0 37761024 0 0
test-fio-zram-LZ4HC
mm_stat (jobs1): 3221225472 23592960 37761024 0 37761024 0 0
mm_stat (jobs2): 3221225472 23592960 37761024 0 37761024 0 0
mm_stat (jobs3): 3221225472 23592960 37761024 0 37761024 0 0
test-fio-zram-LZO
mm_stat (jobs1): 3221225472 34603008 50335744 0 50335744 0 0
mm_stat (jobs2): 3221225472 34603008 50335744 0 50335744 0 0
mm_stat (jobs3): 3221225472 34603008 50335744 0 50339840 0 0
This patch (of 8):
We don't perform any zstream idle list lookup anymore, so
zcomp_strm_find()/zcomp_strm_release() names are not representative.
Rename to zcomp_stream_get()/zcomp_stream_put().
Link: http://lkml.kernel.org/r/20160531122017.2878-2-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull block driver updates from Jens Axboe:
"This branch also contains core changes. I've come to the conclusion
that from 4.9 and forward, I'll be doing just a single branch. We
often have dependencies between core and drivers, and it's hard to
always split them up appropriately without pulling core into drivers
when that happens.
That said, this contains:
- separate secure erase type for the core block layer, from
Christoph.
- set of discard fixes, from Christoph.
- bio shrinking fixes from Christoph, as a followup up to the
op/flags change in the core branch.
- map and append request fixes from Christoph.
- NVMeF (NVMe over Fabrics) code from Christoph. This is pretty
exciting!
- nvme-loop fixes from Arnd.
- removal of ->driverfs_dev from Dan, after providing a
device_add_disk() helper.
- bcache fixes from Bhaktipriya and Yijing.
- cdrom subchannel read fix from Vchannaiah.
- set of lightnvm updates from Wenwei, Matias, Johannes, and Javier.
- set of drbd updates and fixes from Fabian, Lars, and Philipp.
- mg_disk error path fix from Bart.
- user notification for failed device add for loop, from Minfei.
- NVMe in general:
+ NVMe delay quirk from Guilherme.
+ SR-IOV support and command retry limits from Keith.
+ fix for memory-less NUMA node from Masayoshi.
+ use UINT_MAX for discard sectors, from Minfei.
+ cancel IO fixes from Ming.
+ don't allocate unused major, from Neil.
+ error code fixup from Dan.
+ use constants for PSDT/FUSE from James.
+ variable init fix from Jay.
+ fabrics fixes from Ming, Sagi, and Wei.
+ various fixes"
* 'for-4.8/drivers' of git://git.kernel.dk/linux-block: (115 commits)
nvme/pci: Provide SR-IOV support
nvme: initialize variable before logical OR'ing it
block: unexport various bio mapping helpers
scsi/osd: open code blk_make_request
target: stop using blk_make_request
block: simplify and export blk_rq_append_bio
block: ensure bios return from blk_get_request are properly initialized
virtio_blk: use blk_rq_map_kern
memstick: don't allow REQ_TYPE_BLOCK_PC requests
block: shrink bio size again
block: simplify and cleanup bvec pool handling
block: get rid of bio_rw and READA
block: don't ignore -EOPNOTSUPP blkdev_issue_write_same
block: introduce BLKDEV_DISCARD_ZERO to fix zeroout
NVMe: don't allocate unused nvme_major
nvme: avoid crashes when node 0 is memoryless node.
nvme: Limit command retries
loop: Make user notify for adding loop device failed
nvme-loop: fix nvme-loop Kconfig dependencies
nvmet: fix return value check in nvmet_subsys_alloc()
...
Pull core block updates from Jens Axboe:
- the big change is the cleanup from Mike Christie, cleaning up our
uses of command types and modified flags. This is what will throw
some merge conflicts
- regression fix for the above for btrfs, from Vincent
- following up to the above, better packing of struct request from
Christoph
- a 2038 fix for blktrace from Arnd
- a few trivial/spelling fixes from Bart Van Assche
- a front merge check fix from Damien, which could cause issues on
SMR drives
- Atari partition fix from Gabriel
- convert cfq to highres timers, since jiffies isn't granular enough
for some devices these days. From Jan and Jeff
- CFQ priority boost fix idle classes, from me
- cleanup series from Ming, improving our bio/bvec iteration
- a direct issue fix for blk-mq from Omar
- fix for plug merging not involving the IO scheduler, like we do for
other types of merges. From Tahsin
- expose DAX type internally and through sysfs. From Toshi and Yigal
* 'for-4.8/core' of git://git.kernel.dk/linux-block: (76 commits)
block: Fix front merge check
block: do not merge requests without consulting with io scheduler
block: Fix spelling in a source code comment
block: expose QUEUE_FLAG_DAX in sysfs
block: add QUEUE_FLAG_DAX for devices to advertise their DAX support
Btrfs: fix comparison in __btrfs_map_block()
block: atari: Return early for unsupported sector size
Doc: block: Fix a typo in queue-sysfs.txt
cfq-iosched: Charge at least 1 jiffie instead of 1 ns
cfq-iosched: Fix regression in bonnie++ rewrite performance
cfq-iosched: Convert slice_resid from u64 to s64
block: Convert fifo_time from ulong to u64
blktrace: avoid using timespec
block/blk-cgroup.c: Declare local symbols static
block/bio-integrity.c: Add #include "blk.h"
block/partition-generic.c: Remove a set-but-not-used variable
block: bio: kill BIO_MAX_SIZE
cfq-iosched: temporarily boost queue priority for idle classes
block: drbd: avoid to use BIO_MAX_SIZE
block: bio: remove BIO_MAX_SECTORS
...
Commit 9d092603cc ("xen-blkback: do not leak mode property") left one
path unfixed; correct this.
Acked-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The functions these get passed to have been taking pointers to const
since at least 2.6.16.
Acked-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
... for single items being collected: It is more typesafe (as the
compiler can check format string and to-be-written-to variable match)
and requires one less parameter to be passed.
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
... for single items being collected: It is more typesafe (as the
compiler can check format string and to-be-written-to variable match)
and requires one less parameter to be passed.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Currently, presence of direct_access() in block_device_operations
indicates support of DAX on its block device. Because
block_device_operations is instantiated with 'const', this DAX
capablity may not be enabled conditinally.
In preparation for supporting DAX to device-mapper devices, add
QUEUE_FLAG_DAX to request_queue flags to advertise their DAX
support. This will allow to set the DAX capability based on how
mapped device is composed.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <linux-s390@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_get_request is used for BLOCK_PC and similar passthrough requests.
Currently we always need to call blk_rq_set_block_pc or an open coded
version of it to allow appending bios using the request mapping helpers
later on, which is a somewhat awkward API. Instead move the
initialization part of blk_rq_set_block_pc into blk_get_request, so that
we always have a safe to use request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Similar to how SCSI and NVMe prepare passthrough requests. This avoids
poking into request internals too much.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
These two are confusing leftover of the old world order, combining
values of the REQ_OP_ and REQ_ namespaces. For callers that don't
special case we mostly just replace bi_rw with bio_data_dir or
op_is_write, except for the few cases where a switch over the REQ_OP_
values makes more sense. Any check for READA is replaced with an
explicit check for REQ_RAHEAD. Also remove the READA alias for
REQ_RAHEAD.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The __pmem address space was meant to annotate codepaths that touch
persistent memory and need to coordinate a call to wmb_pmem(). Now that
wmb_pmem() is gone, there is little need to keep this annotation.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is no error number returned if loop driver fails in function
alloc_disk to add new loop device. Add a correct error number to make
user notify in this case.
Signed-off-by: Minfei Huang <mnghuan@gmail.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Dan writes:
"The removal of ->driverfs_dev in favor of just passing the parent
device in as a parameter to add_disk(). See below, it has received a
"Reviewed-by" from Christoph, Bart, and Johannes.
It is also a pre-requisite for Fam Zheng's work to cleanup gendisk
uevents vs attribute visibility [1]. We would extend device_add_disk()
to take an attribute_group list.
This is based off a branch of block.git/for-4.8/drivers and has
received a positive build success notification from the kbuild robot
across several configs.
[1]: "gendisk: Generate uevent after attribute available"
http://marc.info/?l=linux-virtualization&m=146725201522201&w=2"
Pull block IO fixes from Jens Axboe:
"Three small fixes that have been queued up and tested for this series:
- A bug fix for xen-blkfront from Bob Liu, fixing an issue with
incomplete requests during migration.
- A fix for an ancient issue in retrieving the IO priority of a
different PID than self, preventing that task from going away while
we access it. From Omar.
- A writeback fix from Tahsin, fixing a case where we'd call ihold()
with a zero ref count inode"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix use-after-free in sys_ioprio_get()
writeback: inode cgroup wb switch should not call ihold()
xen-blkfront: save uncompleted reqs in blkfront_resume()
Uncompleted reqs used to be 'saved and resubmitted' in blkfront_recover() during
migration, but that's too late after multi-queue was introduced.
After a migrate to another host (which may not have multiqueue support), the
number of rings (block hardware queues) may be changed and the ring and shadow
structure will also be reallocated.
The blkfront_recover() then can't 'save and resubmit' the real
uncompleted reqs because shadow structure have been reallocated.
This patch fixes this issue by moving the 'save' logic out of
blkfront_recover() to earlier place in blkfront_resume().
The 'resubmit' is not changed and still in blkfront_recover().
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: stable@vger.kernel.org
MG_DISK_MAJ is defined as 0 so dynamic block major number
allocation is used by the driver and the assigned major
number is stored in host->major. This patch fixes error
path in mg_probe() to use host->major instead of using
MG_DISK_MAJ.
Cc: unsik Kim <donari75@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For block drivers that specify a parent device, convert them to use
device_add_disk().
This conversion was done with the following semantic patch:
@@
struct gendisk *disk;
expression E;
@@
- disk->driverfs_dev = E;
...
- add_disk(disk);
+ device_add_disk(E, disk);
@@
struct gendisk *disk;
expression E1, E2;
@@
- disk->driverfs_dev = E1;
...
E2 = disk;
...
- add_disk(E2);
+ device_add_disk(E1, E2);
...plus some manual fixups for a few missed conversions.
Cc: Jens Axboe <axboe@fb.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This is the third version of the patchset previously sent [1]. I have
basically only rebased it on top of 4.7-rc1 tree and dropped "dm: get
rid of superfluous gfp flags" which went through dm tree. I am sending
it now because it is tree wide and chances for conflicts are reduced
considerably when we want to target rc2. I plan to send the next step
and rename the flag and move to a better semantic later during this
release cycle so we will have a new semantic ready for 4.8 merge window
hopefully.
Motivation:
While working on something unrelated I've checked the current usage of
__GFP_REPEAT in the tree. It seems that a majority of the usage is and
always has been bogus because __GFP_REPEAT has always been about costly
high order allocations while we are using it for order-0 or very small
orders very often. It seems that a big pile of them is just a
copy&paste when a code has been adopted from one arch to another.
I think it makes some sense to get rid of them because they are just
making the semantic more unclear. Please note that GFP_REPEAT is
documented as
* __GFP_REPEAT: Try hard to allocate the memory, but the allocation attempt
* _might_ fail. This depends upon the particular VM implementation.
while !costly requests have basically nofail semantic. So one could
reasonably expect that order-0 request with __GFP_REPEAT will not loop
for ever. This is not implemented right now though.
I would like to move on with __GFP_REPEAT and define a better semantic
for it.
$ git grep __GFP_REPEAT origin/master | wc -l
111
$ git grep __GFP_REPEAT | wc -l
36
So we are down to the third after this patch series. The remaining
places really seem to be relying on __GFP_REPEAT due to large allocation
requests. This still needs some double checking which I will do later
after all the simple ones are sorted out.
I am touching a lot of arch specific code here and I hope I got it right
but as a matter of fact I even didn't compile test for some archs as I
do not have cross compiler for them. Patches should be quite trivial to
review for stupid compile mistakes though. The tricky parts are usually
hidden by macro definitions and thats where I would appreciate help from
arch maintainers.
[1] http://lkml.kernel.org/r/1461849846-27209-1-git-send-email-mhocko@kernel.org
This patch (of 19):
__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations. Yet we
have the full kernel tree with its usage for apparently order-0
allocations. This is really confusing because __GFP_REPEAT is
explicitly documented to allow allocation failures which is a weaker
semantic than the current order-0 has (basically nofail).
Let's simply drop __GFP_REPEAT from those places. This would allow to
identify place which really need allocator to retry harder and formulate
a more specific semantic for what the flag is supposed to do actually.
Link: http://lkml.kernel.org/r/1464599699-30131-2-git-send-email-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com> [for tile]
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: John Crispin <blogic@openwrt.org>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
crypto_alloc_hash returns an ERR_PTR(), not NULL.
Also reset peer_integrity_tfm to NULL, to not call crypto_free_hash()
on an errno in the cleanup path.
Reported-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For larger devices, the array of bitmap page pointers can grow very
large (8000 pointers per TB of storage).
For each activity log transaction, we need to flush the associated
bitmap pages to stable storage. Currently, we just "mark" the respective
pages while setting up the transaction, then tell the bitmap code to
write out all marked pages, but skip unchanged pages.
But one such transaction can affect only a small number of bitmap pages,
there is no need to scan the full array of several (ten-)thousand
page pointers to find the few marked ones.
Instead, remember the index numbers of the few affected pages,
and later only re-check those to skip duplicates and unchanged ones.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Also skip the message unless bitmap IO took longer than 5 ms.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Christoph Hellwig