The reconnect path is calling the init routines to clear a queue
structure. But the queue structure has state that perhaps needs
to persist as long as the controller is live.
Remove the nvme_fc_init_queue() calls on reconnect.
The nvme_fc_free_queue() calls will clear state bits and reset
any relevant queue state for a new connection.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The reinit_request routine is not necessary. Remove support for the
op callback.
As all that nvme_reinit_tagset() does is itterate and call the
reinit routine, it too has no purpose. Remove the call.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Current code follows the framework that has been in the transports
from the beginning where initial link-side controller connect occurs
as part of "creating the controller". Thus that first connect fully
talks to the controller and obtains values that can then be used in
for blk-mq setup, etc. It also means that everything about the
controller is fully know before the "create controller" call returns.
This has several weaknesses:
- The initial create_ctrl call made by the cli will block for a long
time as wire transactions are performed synchronously. This delay
becomes longer if errors occur or connectivity is lost and retries
need to be performed.
- Code wise, it means there is a separate connect path for initial
controller connect vs the (same) steps used in the reconnect path.
- And as there's separate paths, it means there's separate error
handling and retry logic. It also plays havoc with the NEW state
(should transition out of it after successful initial connect) vs
the RESETTING and CONNECTING (reconnect) states that want to be
transitioned to on error.
- As there's separate paths, to recover from errors and disruptions,
it requires separate recovery/retry paths as well and can severely
convolute the controller state.
This patch reworks the fc transport to use the same connect paths
for the initial connection as it uses for reconnect. This makes a
single path for error recovery and handling.
This patch:
- Removes the driving of the initial connect and replaces it with
a state transition to CONNECTING and initiating the reconnect
thread. A dummy state transition of RESETTING had to be traversed
as a direct transtion of NEW->CONNECTING is not allowed. Given
that the controller is "new", the RESETTING transition is a simple
no-op. Once in the reconnecting thread, the normal behaviors of
ctrl_loss_tmo (max_retries * connect_delay) and dev_loss_tmo will
apply before the controller is torn down.
- Only if the state transitions couldn't be traversed and the
reconnect thread not scheduled, will the controller be torn down
while in create_ctrl.
- The prior code used the controller state of NEW to indicate
whether request queues had been initialized or not. For the admin
queue, the request queue is always created, so there's no need to
check a state. For IO queues, change to tracking whether a successful
io request queue create has occurred (e.g. 1st successful connect).
- The initial controller id is initialized to the dynamic controller
id used in the initial connect message. It will be overwritten by
the real controller id once the controller is connected on the wire.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Don't optimize our namespace rescan based on the changed namespace list
log page as userspace might have changed the content through reading
it.
Suggested-by: Keith Busch <keith.busch@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@linux.intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Free smart-log buffer allocated in the function after use.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
After dma mapping the sgl, we map the sgl to nvme sgl descriptor. In case
of failure during the last mapping we never dma unmap the sgl.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Adding a tracepoint to trace bio remapping for native nvme multipath.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When using nvme-pci driver the nvmf_ctrl_options is NULL.
There is no need to check for discovery_nqn flag at non-fabrics controller.
Fixes: 181303d0 ("nvme-fabrics: allow duplicate connections to the discovery controller")
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The problem here is that set_bit() and test_bit() take a bit number so
we should be passing 0 but instead we're passing (1 << 0) which leads to
a double shift. It doesn't cause a runtime bug in the current code
because it's done consistently and we only set that one bit.
I decided to just re-use NVME_AER_NOTICE_NS_CHANGED instead of
introducing a new define for this.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A controller reset after a run time change of the CMB module parameter
breaks the driver. An 'on -> off' will have the driver use NULL for the
host memory queue, and 'off -> on' will use mismatched queue depth between
the device and the host.
We could fix both, but there isn't really a good reason to change this
at run time anyway, compared to at module load time, so this patch makes
parameter read-only after after modprobe.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch ensures the nvme namsepace request queues are not quiesced
on a surprise removal. It's possible the queues were previously killed
in a failed reset, so the queues need to be unquiesced to ensure all
requests are flushed to completion.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The controller is required to disable its host memory buffer use on
controller reset. We don't need to submit an admin command to delete it,
so this patch skips sending that command so we don't need to worry about
handling a timeout.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We've been ignoring NVMe error status on queue creations. Fortunately they
are uncommon, but we should handle these anyway. This patch adds checks
for the a positive error return value that indicates an NVMe status.
If we do see a negative return, the controller isn't usable, so this
patch returns immediately in since we can't unwind that failure.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The nvme pci driver never unmaps the doorbell registers while the requests
are active, so we can always safely update the completion queue head.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The nvme pci driver no longer handles completions under the cq lock,
so the nested locking is not necessary.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We should avoid consuming the newlines in traddr, trsvcid and
device_path. Add minimal processing to make sure they are gone.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The code was checking bit 20 instead of bit 2. Also fixed the log entry.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Only take nvmf_transports_rwsem when doing a lookup of registered
transports, so that a blocking ->create_ctrl doesn't prevent other
actions on /dev/nvme-fabrics.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
[hch: increased lock hold time a bit to be safe, added a comment
and updated the changelog]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Quote from Figure 106 in NVMe 1.3a:
The Identify Namespace data structure is returned to the host for the
namespace specified in the Namespace Identifier (CDW1.NSID) field if it
is an active NSID. If the specified namespace is not an active NSID,
then the controller returns a zero filled data structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@rimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nga/
-----END PGP SIGNATURE-----
Merge tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- clean up how we pass around gfp_t and
blk_mq_req_flags_t (Christoph)
- prepare us to defer scheduler attach (Christoph)
- clean up drivers handling of bounce buffers (Christoph)
- fix timeout handling corner cases (Christoph/Bart/Keith)
- bcache fixes (Coly)
- prep work for bcachefs and some block layer optimizations (Kent).
- convert users of bio_sets to using embedded structs (Kent).
- fixes for the BFQ io scheduler (Paolo/Davide/Filippo)
- lightnvm fixes and improvements (Matias, with contributions from Hans
and Javier)
- adding discard throttling to blk-wbt (me)
- sbitmap blk-mq-tag handling (me/Omar/Ming).
- remove the sparc jsflash block driver, acked by DaveM.
- Kyber scheduler improvement from Jianchao, making it more friendly
wrt merging.
- conversion of symbolic proc permissions to octal, from Joe Perches.
Previously the block parts were a mix of both.
- nbd fixes (Josef and Kevin Vigor)
- unify how we handle the various kinds of timestamps that the block
core and utility code uses (Omar)
- three NVMe pull requests from Keith and Christoph, bringing AEN to
feature completeness, file backed namespaces, cq/sq lock split, and
various fixes
- various little fixes and improvements all over the map
* tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block: (196 commits)
blk-mq: update nr_requests when switching to 'none' scheduler
block: don't use blocking queue entered for recursive bio submits
dm-crypt: fix warning in shutdown path
lightnvm: pblk: take bitmap alloc. out of critical section
lightnvm: pblk: kick writer on new flush points
lightnvm: pblk: only try to recover lines with written smeta
lightnvm: pblk: remove unnecessary bio_get/put
lightnvm: pblk: add possibility to set write buffer size manually
lightnvm: fix partial read error path
lightnvm: proper error handling for pblk_bio_add_pages
lightnvm: pblk: fix smeta write error path
lightnvm: pblk: garbage collect lines with failed writes
lightnvm: pblk: rework write error recovery path
lightnvm: pblk: remove dead function
lightnvm: pass flag on graceful teardown to targets
lightnvm: pblk: check for chunk size before allocating it
lightnvm: pblk: remove unnecessary argument
lightnvm: pblk: remove unnecessary indirection
lightnvm: pblk: return NVM_ error on failed submission
lightnvm: pblk: warn in case of corrupted write buffer
...
- bnxt netdev changes merged this cycle caused the bnxt RDMA driver to crash under
certain situations
- Arnd found (several, unfortunately) kconfig problems with the patches adding
INFINIBAND_ADDR_TRANS. Reverting this last part, will fix it more fully
outside -rc.
- Subtle change in error code for a uapi function caused breakage in userspace.
This was bug was subtly introduced cycle
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ppe+
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Just three small last minute regressions that were found in the last
week. The Broadcom fix is a bit big for rc7, but since it is fixing
driver crash regressions that were merged via netdev into rc1, I am
sending it.
- bnxt netdev changes merged this cycle caused the bnxt RDMA driver
to crash under certain situations
- Arnd found (several, unfortunately) kconfig problems with the
patches adding INFINIBAND_ADDR_TRANS. Reverting this last part,
will fix it more fully outside -rc.
- Subtle change in error code for a uapi function caused breakage in
userspace. This was bug was subtly introduced cycle"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/core: Fix error code for invalid GID entry
IB: Revert "remove redundant INFINIBAND kconfig dependencies"
RDMA/bnxt_re: Fix broken RoCE driver due to recent L2 driver changes
Pull NVMe changes from Christoph:
"Below is another set of NVMe updates for 4.18. Besides the usual bug
fixes this includes more feature completness in terms of AEN and log
page handling on the target."
* 'nvme-4.18' of git://git.infradead.org/nvme:
nvme: use the changed namespaces list log to clear ns data changed AENs
nvme: mark nvme_queue_scan static
nvme: submit AEN event configuration on startup
nvmet: mask pending AENs
nvmet: add AEN configuration support
nvmet: implement the changed namespaces log
nvmet: split log page implementation
nvmet: add a new nvmet_zero_sgl helper
nvme.h: add AEN configuration symbols
nvme.h: add the changed namespace list log
nvme.h: untangle AEN notice definitions
nvmet: fix error return code in nvmet_file_ns_enable()
nvmet: fix a typo in nvmet_file_ns_enable()
nvme-fabrics: allow internal passthrough command on deleting controllers
nvme-loop: add support for multiple ports
nvme-pci: simplify __nvme_submit_cmd
nvme-pci: Rate limit the nvme timeout warnings
nvme: allow duplicate controller if prior controller being deleted
Per section 5.2 we need to issue the corresponding log page to clear an
AEN, so for a namespace data changed AEN we need to read the changed
namespace list log. And once we read that log anyway we might as well
use it to optimize the rescan.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
And move it toward the top of the file to avoid a forward declaration.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
We should register for AEN events; some law-abiding targets might
not be sending us AENs otherwise.
Signed-off-by: Hannes Reinecke <hare@suse.com>
[hch: slight cleanups]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Per section 5.2 of the NVMe 1.3 spec:
"When the controller posts a completion queue entry for an outstanding
Asynchronous Event Request command and thus reports an asynchronous
event, subsequent events of that event type are automatically masked by
the controller until the host clears that event. An event is cleared by
reading the log page associated with that event using the Get Log Page
command (see section 5.14)."
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
AEN configuration via the 'Get Features' and 'Set Features' admin
command is mandatory, so we should be implemeting handling for it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
[hch: use WRITE_ONCE, check for invalid values]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Just keep a per-controller buffer of changed namespaces and copy it out
in the get log page implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Remove the common code to allocate a buffer and copy it into the SGL.
Instead the two no-op implementations just zero the SGL directly, and
the smart log allocates a buffer on its own. This prepares for the
more elaborate ANA log page.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Zeroes the SGL in the payload.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Stop including the event type in the definitions for the notice type.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Fix to return error code -ENOMEM from the memory alloc fail error
handling case instead of 0, as done elsewhere in this function.
Fixes: d5eff33ee6 ("nvmet: add simple file backed ns support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.e>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Without this we can't cleanly shut down.
Based on analysis an an earlier patch from Hannes Reinecke.
Fixes: bb06ec3145 ("nvme: expand nvmf_check_if_ready checks")
Reported-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: James Smart <james.smart@broadcom.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Dk2i
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20180530' of git://git.kernel.dk/linux-block
Pull block fix from Jens Axboe:
"Just a single fix that should make it into this release, fixing a
regression with T10-DIF on NVMe"
* tag 'for-linus-20180530' of git://git.kernel.dk/linux-block:
nvme: fix extended data LBA supported setting
We already check for started commands in all callbacks, but we should
also protect against already completed commands. Do this by taking
the checks to common code.
Acked-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With recent CQ handling improvements we can now move the locking into
__nvme_submit_cmd. Also remove the local tail variable to make the code
more obvious, remove the __ prefix in the name, and fix the comments
describing the function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
The block layer's timeout handling currently prevents drivers from
completing commands outside the timeout callback once blk-mq decides
they've expired. If a device breaks, this could potentially create many
thousands of timed out commands. There's nothing of value to be gleaned
from observing each of those messages, so this patch adds a rate limit
on them.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The current checks for whether a new controller request "matches" an
existing controller ignores controller state and checks identity strings.
There are cases where an existing controller may be in its last steps of
deletion when they are "matched" by a new connection.
Change the behavior so that the new connection ignores controllers that
are deleted.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Pull NVMe changes from Christoph:
"Here is the current batch of nvme updates for 4.18, we have a few more
patches in the queue, but I'd like to get this pile into your tree
and linux-next ASAP.
The biggest item is support for file-backed namespaces in the NVMe
target from Chaitanya, in addition to that we mostly small fixes from
all the usual suspects."
* 'nvme-4.18-2' of git://git.infradead.org/nvme:
nvme: fixup memory leak in nvme_init_identify()
nvme: fix KASAN warning when parsing host nqn
nvmet-loop: use nr_phys_segments when map rq to sgl
nvmet-fc: increase LS buffer count per fc port
nvmet: add simple file backed ns support
nvmet: remove duplicate NULL initialization for req->ns
nvmet: make a few error messages more generic
nvme-fabrics: allow duplicate connections to the discovery controller
nvme-fabrics: centralize discovery controller defaults
nvme-fabrics: remove unnecessary controller subnqn validation
nvme-fc: remove setting DNR on exception conditions
nvme-rdma: stop admin queue before freeing it
nvme-pci: Fix AER reset handling
nvme-pci: set nvmeq->cq_vector after alloc cq/sq
nvme: host: core: fix precedence of ternary operator
nvme: fix lockdep warning in nvme_mpath_clear_current_path
This value depands on the metadata support value, so reorder the
initialization to fit.
Fixes: b5be3b392 ("nvme: always unregister the integrity profile in __nvme_revalidate_disk")
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
NVMe always completes the request before returning from ->timeout, either
by polling for it, or by disabling the controller. Return BLK_EH_DONE so
that the block layer doesn't even try to complete it again.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Several subsystems depend on INFINIBAND_ADDR_TRANS, which in turn depends
on INFINIBAND. However, when with CONFIG_INIFIBAND=m, this leads to a
link error when another driver using it is built-in. The
INFINIBAND_ADDR_TRANS dependency is insufficient here as this is
a 'bool' symbol that does not force anything to be a module in turn.
fs/cifs/smbdirect.o: In function `smbd_disconnect_rdma_work':
smbdirect.c:(.text+0x1e4): undefined reference to `rdma_disconnect'
net/9p/trans_rdma.o: In function `rdma_request':
trans_rdma.c:(.text+0x7bc): undefined reference to `rdma_disconnect'
net/9p/trans_rdma.o: In function `rdma_destroy_trans':
trans_rdma.c:(.text+0x830): undefined reference to `ib_destroy_qp'
trans_rdma.c:(.text+0x858): undefined reference to `ib_dealloc_pd'
Fixes: 9533b292a7 ("IB: remove redundant INFINIBAND kconfig dependencies")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
If nvme_get_effects_log() failed the 'id' buffer from the previous
nvme_identify_ctrl() call will never be freed.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The host nqn actually is smaller than the space reserved for it,
so we should be using strlcpy to keep KASAN happy.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use blk_rq_nr_phys_segments() instead of blk_rq_payload_bytes() to check
if a command contains data to me mapped. This fixes the case where
a struct requests contains LBAs, but no data will actually be send,
e.g. the pending Write Zeroes support.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Todays limit on concurrent LS's is very small - 4 buffers. With large
subsystem counts or large numbers of initiators connecting, the limit
may be exceeded.
Raise the LS buffer count to 256.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds simple file backed namespace support for NVMeOF target.
The new file io-cmd-file.c is responsible for handling the code for I/O
commands when ns is file backed. Also, we introduce mempools based slow
path using sync I/Os for file backed ns to ensure forward progress under
reclaim.
The old block device based implementation is moved to io-cmd-bdev.c and
use a "nvmet_bdev_" symbol prefix. The enable/disable calls are also
move into the respective files.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
[hch: updated changelog, fixed double req->ns lookup in bdev case]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Christoph Hellwig