Make it clearer that the index starts at 0.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a new function for digital video encoders such as HDMI transmitters.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The use of 'DTV' is very confusing since it normally refers to Digital
TV e.g. DVB etc.
Instead use 'DV' (Digital Video), which nicely corresponds to the
DV Timings API used to configure such receivers and transmitters.
We keep an alias to avoid breaking userspace applications.
Since this alias is only available if __KERNEL__ is *not* defined
(i.e. it is only available for userspace, not kernelspace), any
drivers that use it also have to be converted to the new define.
These drivers are adv7604, adv7842 and tda1997x.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Document the new struct media_v2_entity 'flags' field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Document the new struct media_v2_pad 'index' field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is no way to control the standard of subdevices which are part of
a media device. The ioctls which exists all target video devices
explicitly and the idea is that the video device should talk to the
subdevice. For subdevices part of a media graph this is not possible and
the standard must be controlled on the subdev device directly.
Add four new ioctls to be able to directly interact with subdevices and
control the video standard; VIDIOC_SUBDEV_ENUMSTD, VIDIOC_SUBDEV_G_STD,
VIDIOC_SUBDEV_S_STD and VIDIOC_SUBDEV_QUERYSTD.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a new control V4L2_CID_MPEG_VIDEO_VP9_PROFILE for VP9 profiles. This control
allows selecting the desired profile for VP9 encoder and querying for supported
profiles by VP9 encoder/decoder.
Though this control is similar to V4L2_CID_MPEG_VIDEO_VP8_PROFILE, we need to
separate this control from it because supported profiles usually differ between
VP8 and VP9.
Signed-off-by: Keiichi Watanabe <keiichiw@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a menu control V4L2_CID_MPEG_VIDEO_VP8_PROFILE for VP8 profile and make
V4L2_CID_MPEG_VIDEO_VPX_PROFILE an alias of it. This new control is used to
select the desired profile for VP8 encoder and query for supported profiles by
VP8 encoder/decoder.
Though we have originally a control V4L2_CID_MPEG_VIDEO_VPX_PROFILE and its name
contains 'VPX', it works only for VP8 because supported profiles usually differ
between VP8 and VP9. In addition, this control cannot be used for querying since
it is not a menu control but an integer control, which cannot return an
arbitrary set of supported profiles.
The new control V4L2_CID_MPEG_VIDEO_VP8_PROFILE is a menu control as with
controls for other codec profiles. (e.g. H264)
In addition, this patch also fixes the use of V4L2_CID_MPEG_VIDEO_VPX_PROFILE in
drivers of Qualcomm's venus and Samsung's s5p-mfc.
Signed-off-by: Keiichi Watanabe <keiichiw@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ycbcr_enc, quantization and xfer_func fields are __u16 and not enums.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Drop the '- .. row 1' lines to make it easier to add new rows to
the tables in the future without having to renumber these lines.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clarify the description of status bits, particularly w.r.t. ERROR and NACK.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The API limitation described here is about the CROP API, not about the
entire V4L2.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Split section "Comparison with old cropping API" in paragraphs for
easier reading and improve visible links text.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
These files have an automatically-generated numbering. Rename them
with a name that suggests their meaning.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Having two somewhat similar and largely overlapping APIs is confusing,
especially since the older one appears in the docs before the newer
and most featureful counterpart.
Clarify all of this in several ways:
- swap the two sections
- give a name to the two APIs in the section names
- add a note at the beginning of the CROP API section
- update note about VIDIOC_CROPCAP
Also remove a note that is incorrect (correct wording is in
vidioc-cropcap.rst).
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This fixes the warning:
Documentation/media/uapi/rc/lirc-func.rst:9: WARNING: toctree contains reference to nonexisting document 'media/uapi/rc/lirc-get-rec-timeout'
The ioctl is documented in lirc-set-rec-timeout.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are two places pointing to an unexisting "m.chehab@kernel.org"
email. I never had such email, so, I'm unsure how it ends there.
Anyway, it is plain wrong.
While here, use my canonical e-mail on a bunch of places that
are pointing to another e-mail. The idea is that, from now on,
all places will be pointing to the same SMTP server.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
From now on, I'll start using my @kernel.org as my development e-mail.
As such, let's remove the entries that point to the old
mchehab@s-opensource.com at MAINTAINERS file.
For the files written with a copyright with mchehab@s-opensource,
let's keep Samsung on their names, using mchehab+samsung@kernel.org,
in order to keep pointing to my employer, with sponsors the work.
For the files written before I join Samsung (on July, 4 2013),
let's just use mchehab@kernel.org.
For bug reports, we can simply point to just kernel.org, as
this will reach my mchehab+samsung inbox anyway.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Brian Warner <brian.warner@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since the kernel now modifies the timeout, make it possible to retrieve
the current value.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On the raspberry pi, we might have two lirc devices; one for sending and
one for receiving. This change makes it much more apparent which one
is which.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
V4L2_CID_DV_RX_POWER_PRESENT refers to a receiver, not a transmitter.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The MEDIA_ENT_F_* defines refer to functions, not types. Update the
documentation accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The size of the reserved arrays in the documentation is wrong. Sync
this with the actual header.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_pix_format documentation still had 'enum's as types.
Replace by __u32 and add a reference to the enum.
Also put ycbcr_enc and hsv_enc in a union.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_pix_format_mplane documentation still had 'enum's as types.
Replace by __u8 and add a reference to the enum.
Also put ycbcr_enc and hsv_enc in a union.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC Pin framework adds support for Error Injection.
Document all the error injections commands and how to use it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
LaTeX adjustbox is known to cause pdf documentation build breakages
with some newer Sphinx versions. So, don't use it.
While here, adjust table sizes in order to better produce the
pdf output.
Fixes: c0da55b95b ("media: v4l2: Documentation for HEVC CIDs")
Cc: Smitha T Murthy <smitha.t@samsung.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Added V4L2 controls for HEVC encoder.
with V4L2_MPEG_VIDEO_HEVC_PROFILE_MAIN_10 to match the code.
[s.nawrocki@samsung.com]: Replaced V4L2_MPEG_VIDEO_HEVC_PROFILE_MAIN10
Signed-off-by: Smitha T Murthy <smitha.t@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add V4L2 definition for HEVC compressed format which is also
known as H.265.
Signed-off-by: Smitha T Murthy <smitha.t@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Links like :ref:`VIDIOC_STREAMON` expand to "ioctl VIDIOC_STREAMON,
VIDIOC_STREAMOFF". Thus our reader will think we are talking about
STREAMON _and_ STREAMOFF, but only one of the two actually applies
in some cases.
Fix by adding a link title, so the reader will read only the correct
ioctl name.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* commit 'v4.16-rc4~0': (900 commits)
Linux 4.16-rc4
memremap: fix softlockup reports at teardown
libnvdimm: re-enable deep flush for pmem devices via fsync()
MAINTAINERS: take over Kconfig maintainership
vfio: disable filesystem-dax page pinning
kconfig: fix line number in recursive inclusion error message
Coccinelle: memdup: Fix typo in warning messages
i2c: octeon: Prevent error message on bus error
parisc: Reduce irq overhead when run in qemu
parisc: Use cr16 interval timers unconditionally on qemu
parisc: Check if secondary CPUs want own PDC calls
parisc: Hide virtual kernel memory layout
parisc: Fix ordering of cache and TLB flushes
kconfig: Update ncurses package names for menuconfig
kbuild/kallsyms: trivial typo fix
kbuild: test --build-id linker flag by ld-option instead of cc-ldoption
kbuild: drop superfluous GCC_PLUGINS_CFLAGS assignment
kconfig: Don't leak choice names during parsing
sh: fix build error for empty CONFIG_BUILTIN_DTB_SOURCE
kconfig: set SYMBOL_AUTO to the symbol marked with defconfig_list
...
Since commit a60d64b15c ("media: lirc: lirc interface should not be
a raw decoder"), the message in the documentation is incorrect as the
module name is rc_core, not lirc_dev. Since the message is not useful,
just make the message debug and remove it from the documentation.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These structures have reserved fields that were never documented.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The MEDIA_IOC_G_TOPOLOGY documentation didn't document the reservedX
fields. Related to that was that the documented type of the num_* fields
was also wrong.
Fix both.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
data conector -> connector
... -> etc.
'...' looked odd when my browser put the ... by itself on the next line, 'etc.'
is clearer IMHO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The source_id and sink_id descriptions were the same for interface-to-entity
links. The source_id is the interface ID, not the entity ID. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_mbus_fmt width and height corresponds directly with the
v4l2_pix_format definitions, yet the differences in documentation make
it ambiguous what to do in the event of field heights.
Clarify this using the same text as is provided for the v4l2_pix_format
which is explicit on the matter, and by matching the terminology of
'image height' rather than the misleading 'frame height'.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The description for VIDIOC_PREPARE_BUF results in the following
sentence: "...before actually enqueuing it, using the ioctl VIDIOC_QBUF,
VIDIOC_DQBUF ioctl...".
The intent is to only refer to VIDIOC_QBUF though, so fix this.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The link was showing both VIDIOC_QBUF, VIDIOC_DQBUF while it should show
only VIDIOC_QBUF in this case.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While userspace can detect discontinuity errors, it is useful to
also let Kernelspace reporting discontinuity, as it can help to
identify if the data loss happened either at Kernel or userspace side.
Update documentation accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a new media entity function definition for digital TV decoders:
MEDIA_ENT_F_DTV_DECODER
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The specification mentions that type can be V4L2_BUF_TYPE_VIDEO_CAPTURE,
but the v4l2 core implementation also allows the _MPLANE variant.
Document this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ioctl change the current mode or return the current mode; they
do not tell you which modes are possible (use the lirc features
ioctl for that).
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit 9b6192589b ("media: lirc: implement scancode sending"),
and commit de142c3241 ("media: lirc: implement reading scancode")
the lirc features ioctl for raw IR devices advertises two modes for
sending and receiving.
The lirc daemon now fails to detect a raw IR device, both for transmit
and receive.
To fix this, do not advertise the scancode mode in the lirc features
for raw IR devices (however do keep it for scancode devices). The mode
can still be used via the LIRC_SET_{REC,SEND}_MODE ioctl.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a pixel format, used by the UVC driver to stream metadata.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The references in Intel IPU3 Bayer format documentation were wrong. Fix
them.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The "reserved" field was a way, used at V4L2 API, to add new
data to existing structs without breaking userspace. However,
there are now clever ways of doing that, without needing to add
an uneeded overhead. So, get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
5 new ioctls were added to the DVB demux API, in order to
handle memory maped I/O. Add documentation for them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With the new dmx mmap interface, those two syscalls are now
handled by the subsystem. Document them.
This patch is based on the V4L2 text for those ioctls.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This commit adds a new property DTV_SCRAMBLING_SEQUENCE_INDEX.
This 18 bit field, when present, carries the index of the DVB-S2 physical
layer scrambling sequence as defined in clause 5.5.4 of EN 302 307.
There is no explicit signalling method to convey scrambling sequence index
to the receiver. If S2 satellite delivery system descriptor is available
it can be used to read the scrambling sequence index (EN 300 468 table 41).
By default, gold scrambling sequence index 0 is used. The valid scrambling
sequence index range is from 0 to 262142.
Increase the DVB API version in order userspace to be aware of the changes.
Signed-off-by: Athanasios Oikonomou <athoik@gmail.com>
Acked-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The semantics for lirc IR transmit with raw IR is that the write call
should block until the IR is transmitted. Some drivers have no idea
when this actually is (e.g. mceusb), so there is a wait.
This is useful for userspace, as it might want to send a IR button press,
a gap of a predefined number of milliseconds, and then send a repeat
message.
It turns out that for transmitting scancodes this feature is even more
useful, as user space has no idea how long the IR is. So, maintain
the existing semantics for IR scancode transmit.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The description of V4L2_DV_FL_HALF_LINE mixed up frontporch with backporch.
It's the backporch that has different sizes for interlaced formats, the frontporch
remains constant.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is part of the uAPI. Add it to the documentation again,
and fix cross-references.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Sean Young <sean@mess.org>
Lirc supports a new mode which requires documentation.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
LIRCCODE is a lirc mode where a driver produces driver-dependent
codes for receive and transmit. No driver uses this any more. The
LIRC_GET_LENGTH ioctl was used for this mode only.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=d9nT
-----END PGP SIGNATURE-----
Merge tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation for digital TV (both kAPI and uAPI) are now in sync
with the implementation (except for legacy/deprecated ioctls). This
is a major step, as there were always a gap there
- New sensor driver: imx274
- New cec driver: cec-gpio
- New platform driver for rockship rga and tegra CEC
- New RC driver: tango-ir
- Several cleanups at atomisp driver
- Core improvements for RC, CEC, V4L2 async probing support and DVB
- Lots of drivers cleanup, fixes and improvements.
* tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (332 commits)
dvb_frontend: don't use-after-free the frontend struct
media: dib0700: fix invalid dvb_detach argument
media: v4l2-ctrls: Don't validate BITMASK twice
media: s5p-mfc: fix lockdep warning
media: dvb-core: always call invoke_release() in fe_free()
media: usb: dvb-usb-v2: dvb_usb_core: remove redundant code in dvb_usb_fe_sleep
media: au0828: make const array addr_list static
media: cx88: make const arrays default_addr_list and pvr2000_addr_list static
media: drxd: make const array fastIncrDecLUT static
media: usb: fix spelling mistake: "synchronuously" -> "synchronously"
media: ddbridge: fix build warnings
media: av7110: avoid 2038 overflow in debug print
media: Don't do DMA on stack for firmware upload in the AS102 driver
media: v4l: async: fix unregister for implicitly registered sub-device notifiers
media: v4l: async: fix return of unitialized variable ret
media: imx274: fix missing return assignment from call to imx274_mode_regs
media: camss-vfe: always initialize reg at vfe_set_xbar_cfg()
media: atomisp: make function calls cleaner
media: atomisp: get rid of storage_class.h
media: atomisp: get rid of wrong stddef.h include
...
That section is too outdated and got superseded by DVBv5 and
by libdvbv5.
Maybe some day we'll end adding updated examples there, but
while nobody has time or interest of doing that, just mention
that there and get rid of the current examples for good.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several problems with regards to the return of
FE_SET_PROPERTY. The original idea were to return per-property
return codes via tvp->result field, and to return an updated
set of values.
However, that never worked. What's actually implemented is:
- the FE_SET_PROPERTY implementation doesn't call .get_frontend
callback in order to get the actual parameters after return;
- the tvp->result field is only filled if there's no error.
So, it is always filled with zero;
- FE_SET_PROPERTY doesn't call memdup_user() nor any other
copy_to_user() function. So, any changes to the properties
will be lost;
- FE_SET_PROPERTY is declared as a write-only ioctl (IOW).
While we could fix the above, it could cause regressions.
So, let's just assume what the code really does, updating
the documentation accordingly and removing the logic that
would update the discarded tvp->result.
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CEC_TX_STATUS_ERROR can be used if the HW cannot tell LOST_ARB and
LOW_DRIVE apart, or when some other error occurs. It is not a
replacement for NACK.
So the hardware must be able to tell the difference between OK, NACK and
'something else'.
Clarify the documentation (both public and kernel API) on this point.
Also fix two small typos (this messages -> this message).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The documentation talked about INITIAL_VALUE when the actual define is
INITIAL_STATE.
Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's a chapter for the legacy APIs. Move the frontend DVBv3
API to it, and update the chapter's introduction accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adjust the table to be better displayed on PDF output.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There appears to be an issue in using \small in certain cases on Sphinx
1.4 and 1.5. Other format documents don't use \small either, remove it
from here as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
[mchehab@s-opensource.com: kept tabularcolumns - readjusted - and
add a few blank lines for it to display better]
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On several tables, the color sample location table preamble is
written as:
Color Sample Location..
Instead of:
Color Sample Location:
I suspect that the repetition of such pattern was due to some
copy-and-paste (or perhaps some error during DocBook conversion).
Anyway, fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While doing a visual inspection with Sphinx 1.5, I noticed that
one of the columns was smaller than the text written there.
As this is the only thing I noticed with Sphinx 1.5, I suspect
that this was also a problem with Sphinx 1.4. Yet, I opted to
touch it in a way that wouldn't cause backward issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It doesn't make any sense having a driver programming's chapter
at the uAPI book, as this is related to kernel API. Also,
we now have such kAPI book where V4L2 driver programming is covered.
So, get rid of this left-over.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's an important note there, but it is not using the
ReST markup. So, it doesn't get any visual highlight on
the output.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The "Table of Contents" of a PDF file is generated only once,
at the beginning fo the output. It doesn't produce it on
each part.
So, don't output this text on each part of the document.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several tables at this media book chapter have issues
when PDF is produced. Adjust them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A literal box provides a better visual when pdf and html output
is generated for things like the output of a sysfs devnode.
It alsod matches other conventions used within the media book.
So, use it.
While here, use literals for protocol names.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit 70b074df4e ("media: fix pdf build with Spinx 1.6") caused
a regression at Sphinx 1.4 PDF build: although it produces a full
document in batch mode, it returns errors on interactive mode:
[63]
Runaway argument?
{\relax
! Paragraph ended before \multicolumn was complete.
<to be read again>
\par
l.7703 \hline\end{tabulary}
The error seems to be due to some bug at Sphinx PDF output:
when multicolumns is used, it doesn't accept an empty string.
Just removing the :cpan:`1` and replacing by two empty
columns fix the issue.
Fixes: 70b074df4e ("media: fix pdf build with Spinx 1.6")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On tests with Spinx 1.4, some tables are still writing text
outside cells. Adjust those tables.
PS.: As this was revisited several times, I suspect that this
will only be fully fixed if we add tabularcolumns to all tables
at the V4L2 part of the book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Tuner Audio Matrix table is broken: the first row has 7
columns instead of 6, causing it to be parsed wrong and displayed
very badly on PDF output.
Fix it and adjust the table to look nice at PDF output
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the past, V4L2 versions were 0.x.y, but that changed years
ago. Since Kernel 3.1, however, the numbering schema was changed
to match the Kernel version.
However, the presented example still uses the old numerating
schema, with is a misleading information.
So, update it to the new schema.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several ioctls are missing descriptions for the third argument
of the ioctl() command. They should have a description, as
otherwise the output won't be ok, and will sound like something
is missing.
So, add them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Usually, CA messages are sent/received via reading/writing at
the CA device node. However, two drivers (dst_ca and firedtv-ci)
also implement it via ioctls.
Apparently, on both cases, the net result is the same.
Anyway, let's document it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The av7110 driver uses CA_SET_DESCR to store the descrambler
control words at the CA descrambler slots.
Document it.
Thanks-to: Honza Petrouš <jpetrous@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we did with frontend.h, ca.h and dmx.h, move the struct
definition to net.h.
That should help to keep it updated, as more stuff gets
added there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Originally, when DVB was introduced, all codecs would be part of
MPEG2 standard. That's not true anymore, as there are a large
number of codec standards used on digital TV nowadays.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The hardware description mentions that some parts are optional.
Make it clearer at the drawing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This ioctl is supported by the DVB core, but was never
documented.
Add a documentation for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Do minor editorial changes to improve documentation readability:
- mark literals as such;
- add table markups to hint sizes;
- define what PES means;
- instead of hardcoding devnode numbers to zero (like adapter0/) use a
question mark, to indicate that multiple devnodes may exist;
- add cross-references where useful.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several missing items at the API history. Yet,
as we're doing a significant change there, add a new entry.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The struct that contains an union of DVB parameters is
called dvb_frontend_parameters (and not FrontendParameters).
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the past, the documentation used to say that, if a CRC error
was found, a "-ECRC" error would be returned. That's not true:
the DVB core will just silently ignore such errors.
So, add an explicit note about that.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The usage of the term "DVB" at the dvb API docs is confusing,
as, right now, it can refer to either the European digital TV
standard or to the subsystem.
So, prefer calling it as "Digital TV" on most places, to avoid
ambiguity.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The device node name for CA is wrong since ever. I suspect
that the name there was before DVBv3 (with was the first API
introduced at the Kernel).
Anyway, use the right name there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several issues on the return value for ioctls:
- Text is confusing;
- Some error codes don't exist;
- The non-generic error codes should come before the text
that points to the generic error codes;
- Tables don't contain column size hints;
- Some references are not marked as such.
Correct them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This error can be produced at least at the DVB subsystem.
As it is generic enough, document it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of having one chapter per file, place all of them at
the same chapter. That better organize the chapters at the uAPI
documentation.
As a side effect, now all uAPI headers are at the same page,
at the html output, with makes easier to use it as a reference
index for the spec.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Right now, the same undocumented structs are on two places:
at ca_data_types.rst and together with their ioctls.
Move them to just one place and use the standard way to
represent them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While we don't have any documentation for it, based on what's
there at Kaffeine and VDR, it seems that this command should
be issued before start using CA. So, document it as such.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For most of the stuff there, documenting is easy, as the
header file contains information.
Yet, I was unable to document two data structs:
ca_msg and ca_descr
As those two structs are used by a few drivers, keep them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This ioctl seems to be some attempt to support a feature
at the bt8xx dst_ca driver. Yet, as said there, it
"needs more work". Right now, the code there is just
a boilerplate.
At the end of the day, no driver uses this ioctl, nor it is
documented anywhere (except for "needs more work").
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to a mistake, the DVB net chapter was actually broken
into two different chapters. Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The demux documentation is pretty poor nowadays: most of the
structs and enums aren't documented at all.
Add proper kernel-doc markups for them and use it.
Now, the demux API data structures are fully documented :-)
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This seems to be a pure fictional API :-)
It only exists at the DVB book, with no code implemeting it.
So, just get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's no driver currently using it; it is also not
documented about what it would be supposed to do.
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's a flag defined for Digital TV demux that is not used
anywhere, called DMX_KERNEL_CLIENT. Get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several frontend properties are specific to a subset of the
delivery systems. Make it clearer when describing each
property.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that frontend.h contains most documentation for the frontend,
remove the duplicated information from Documentation/ and use the
kernel-doc auto-generated one instead.
That should simplify maintainership of DVB frontend uAPI, as most
of the documentation will stick with the header file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Both CA and decoders are optional. Also, the presence or
absence has nothing to do on being a PCI card or not.
Nowadays, most hardware leaves the decoders to either the
GPU or to some ISP inside the SoC, instead of implementing
it inside the Digital TV part of the device.
So, change the wording to reflect the hardware changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The references there are only for DVB. Add missing references for
ATSC and ISDB standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On several places at the introduction, a digital TV board and its
kernel support is called as DVB. The reason is simple: by the
time the document was written, there were no other digital TV
standards :-)
Modernize the specs by referring to them as Digital TV.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Recently added FE_NONE to the enum fe_status, so update the
documentation accordingly.
[mchehab@s-opensource.com: change description to actually
reflect what FE_NONE means: no lock of any kind]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Do some minor editorial changes to make this chapter visually
better, and the example a little bit clearer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The description of the DVBv5 API was written a long time ago,
where the API was still new, and there were not apps using it.
Now that the API is stable and used by new applications, clarify
that DVBv3 calls should not be used and why.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ATSC 3.0 uses MPEG Media Transport, with is not currently
supported. Yet, we'll need to implement it sooner or later.
So, mention about it at the specs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The description of what SEC means fits well as a footnote.
That makes the need of saying that SEC is only for Satellite
when it was mentioned, as the footnote already says that.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The introduction for the frontend chapter is not quite
correct:
- it tells that it supports only three types of
delivery systems, in opposite to three *groups*;
- It adds ISDB-C to the list of supported systems,
but, this is not true.
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The device numbering for DVB uses "M" and "N" as vars for the
number of the device, but sometimes this is printed using normal
font instead of verbatim.
While here, remove an extra space after quotation marks.
This is a minor cleanup with no changes at the text.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sphinx 1.6 generates some LaTeX code before each table,
starting its own environment before calling tabulary,
apparently to improve table layout.
The problem is that such environment is incompatible with
adjustbox. While, in thesis, it should be possible to override
it or to redefine tabulary, I was unable to produce such patch.
Also, that would likely break on some future Sphinx version.
So, instead, let's just change the font size on bigger tables,
in order for them to fit into the page size. That is not as
good as adjustbox, and require some manual work, but it should
be less sensitive to Sphinx changes.
While here, adjust a few other tables whose text is exceeding
the cell boundaries.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These formats are compressed 12-bit raw bayer formats with four different
pixel orders. They are similar to 10-bit variants. The formats added by
this patch are
V4L2_PIX_FMT_SBGGR12P
V4L2_PIX_FMT_SGBRG12P
V4L2_PIX_FMT_SGRBG12P
V4L2_PIX_FMT_SRGGB12P
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC_EVENT_PIN_LOW/HIGH defines and the cec_queue_pin_event() function
did not specify that these were about CEC pin events.
Since in the future there will also be HPD pin events it is wise to rename
the event defines and function to CEC_EVENT_PIN_CEC_LOW/HIGH and
cec_queue_pin_cec_event() now before these become part of the ABI.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The description of how messages are processed by the core was not
always very clear. Reword it to improve this.
In particular for the USER_CONTROL_* messages a critical bit was
missing in that the core also checks for the CEC_LOG_ADDRS_FL_ALLOW_RC_PASSTHRU
flag. This was confusing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
`CEC_LOG_ADDRS_FL_CDC_ONLY` should be ``CEC_LOG_ADDRS_FL_CDC_ONLY``.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Various references to open() et al were wrong. Fix this so following
the link will get you to the correct place.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make note of the different luminance ranges between HDR and SDR.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a note stating that bt.2020 is often used in combination with the
smpte 2084 transfer function.
Also use the right references to the documentation of that transfer
function.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
After the DocBook conversion a number of pixfmt description files just
had a number in the filename (pix-fmt-004, 006, etc) which was not very
descriptive.
Rename them.
Note that pixfmt-008.rst was folded into colorspaces-details.rst, so
that file is deleted. It's easier to maintain that way.
Also moved the colorspace sections to the end of the chapter. The old
order was weird: the "Standard Image Formats" section (an intro into
pixel formats) was followed by the colorspace sections instead of the
pixel format descriptions.
Moving it to the end resolved that issue.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The rectangle which the sink compose rectangle is related to is documented
to be the source compose bounds rectangle. This is in obvious conflict with
the ground rule of the format propagation (from sink to source). The reason
behind this is that this was always supposed to be the sink compose bounds
rectangle. Fix it.
Fixes: 955f645aea ("[media] v4l: Add subdev selections documentation")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC version, vendor ID and OSD name were not cleared when clearing the
current set of logical addresses. This was unexpected and somewhat confusing,
so reset all these fields to their default values. Also document this since
the documentation wasn't quite clear either.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sending patches with SVG files via e-mail has a drawback: line
size could be bigger than 998, with is the limit given by
RFC 5322[1]. So, we need to enforce a lower limit, in order to
allow those patches to be properly reviewed.
[1] https://tools.ietf.org/html/rfc5322#section-2.1.1
So, use this small Perl script to limit columns size to ~900.
use Text::Wrap;
$Text::Wrap::columns = 900;
$t.=$_ while (<>);
print wrap("","",$t);
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Debian's ImageMagick is currently unable to decode those
images. Use scour to simplify the SVG, and provide only
one font type, in order to make it more palatable.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This file is too big, with cause it to require a lot
of memory when parsed by texlive.
Optimize it, in order to avoid the need of touching at
main_memory at texmf.cnf.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZapWhAAoJEHm+PkMAQRiGKb0IAJM6b7SbWaw69Og7+qiFB+zZ
xp29iXqbE9fPISC6a5BRQV1ONjeDM6opGixGHqGC8Hla6k2IYz25VDNoF8wd0MXN
cz/Ih20vd3C5afxXGe5cTT8lsPAlV0mWXxForlu6j8jPeL62FPfq6RhEkw7AcrYL
yfYy3k3qSdOrrvBdII0WAAUi46UfIs+we9BQgbsMbkHOiqV2K0MOrzKE84Xbgepq
RAy2xg6P4b4+hTx8xTrYc1MXwpnqjRc0oJ08gdmiwW3AOOU7LxYFn7zDkLPWi9Rr
g4x6r4YhBTGxT4wNvovLIiqd9QFs//dMCuPWYwEtTICG48umIqqq24beQ0mvCdg=
=08Ic
-----END PGP SIGNATURE-----
Merge tag 'v4.13-rc1' into patchwork
Linux v4.13-rc1
* tag 'v4.13-rc1': (11136 commits)
Linux v4.13-rc1
random: reorder READ_ONCE() in get_random_uXX
random: suppress spammy warnings about unseeded randomness
replace incorrect strscpy use in FORTIFY_SOURCE
kmod: throttle kmod thread limit
kmod: add test driver to stress test the module loader
MAINTAINERS: give kmod some maintainer love
xtensa: use generic fb.h
fault-inject: add /proc/<pid>/fail-nth
fault-inject: simplify access check for fail-nth
fault-inject: make fail-nth read/write interface symmetric
fault-inject: parse as natural 1-based value for fail-nth write interface
fault-inject: automatically detect the number base for fail-nth write interface
kernel/watchdog.c: use better pr_fmt prefix
MAINTAINERS: move the befs tree to kernel.org
lib/atomic64_test.c: add a test that atomic64_inc_not_zero() returns an int
mm: fix overflow check in expand_upwards()
ubifs: Set double hash cookie also for RENAME_EXCHANGE
ubifs: Massage assert in ubifs_xattr_set() wrt. init_xattrs
ubifs: Don't leak kernel memory to the MTD
...
-----BEGIN PGP SIGNATURE-----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=RtxO
-----END PGP SIGNATURE-----
Merge tag 'media/v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- addition of fwnode support at V4L2 core
- addition of a few more SDR formats
- new imx driver to support i.MX6 cameras
- new driver for Qualcon venus codecs
- new I2C sensor drivers: dw9714, max2175, ov13858, ov5640
- new CEC driver: stm32-cec
- some improvements to DVB frontend documentation and a few fixups
- several driver improvements and fixups
* tag 'media/v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (361 commits)
[media] media: entity: Catch unbalanced media_pipeline_stop calls
[media] media/uapi/v4l: clarify cropcap/crop/selection behavior
[media] v4l2-ioctl/exynos: fix G/S_SELECTION's type handling
[media] vimc: sen: Declare vimc_sen_video_ops as static
[media] vimc: sca: Add scaler
[media] vimc: deb: Add debayer filter
[media] vimc: Subdevices as modules
[media] vimc: cap: Support several image formats
[media] vimc: sen: Support several image formats
[media] vimc: common: Add vimc_colorimetry_clamp
[media] vimc: common: Add vimc_link_validate
[media] vimc: common: Add vimc_pipeline_s_stream helper
[media] vimc: common: Add vimc_ent_sd_* helper
[media] vimc: Move common code from the core
[media] vimc: sen: Integrate the tpg on the sensor
[media] media: i2c: ov772x: Force use of SCCB protocol
[media] dvb uapi docs: enums are passed by value, not reference
[media] dvb: don't use 'time_t' in event ioctl
[media] media: venus: enable building with COMPILE_TEST
[media] af9013: refactor power control
...
Hans Verkuil