Use the new AdminQ functions for safely accessing the Rx control
registers that may be affected by heavy small packet traffic.
Change-ID: Ibb00983e8dcba71f4b760222a609a5fcaa726f18
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the new opcodes and struct used for asking the firmware to update Rx
control registers that need extra care when being accessed while under
heavy traffic - e.g. sustained 64byte packets at line rate on all ports.
The firmware will take extra steps to be sure the register accesses
are successful.
The registers involved are:
PFQF_CTL_0
PFQF_HENA
PFQF_FDALLOC
PFQF_HREGION
PFLAN_QALLOC
VPQF_CTL
VFQF_HENA
VFQF_HREGION
VSIQF_CTL
VSILAN_QBASE
VSILAN_QTABLE
VSIQF_TCREGION
PFQF_HKEY
VFQF_HKEY
PRTQF_CTL_0
GLFCOE_RCTL
GLFCOE_RSOF
GLQF_CTL
GLQF_SWAP
GLQF_HASH_MSK
GLQF_HASH_INSET
GLQF_HSYM
GLQF_FC_MSK
GLQF_FC_INSET
GLQF_FD_MSK
PRTQF_FD_INSET
PRTQF_FD_FLXINSET
PRTQF_FD_MSK
Change-ID: I56c8144000da66ad99f68948d8a184b2ec2aeb3e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds functions to blink led on devices using
10GBaseT PHY since MAC registers used in other designs
do not work in this device configuration.
Change-ID: Id4b88c93c649fd2b88073a00b42867a77c761ca3
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On all of the other Intel drivers we place checksum close to TSO as they
have a significant amount in common and it can help to reduce the decision
tree for how to handle the frame as the first check in TSO is to see if
checksumming is offloaded, and if it is not we can skip _BOTH_ TSO and Tx
checksum offload based on a single check.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to rewrite the logic for how we determine if we can
transmit the frame or if it needs to be linearized.
The previous code for this function was using a mix of division and modulus
division as a part of computing if we need to take the slow path. Instead
I have replaced this by simply working with a sliding window which will
tell us if the frame would be capable of causing a single packet to span
several descriptors.
The logic for the scan is fairly simple. If any given group of 6 fragments
is less than gso_size - 1 then it is possible for us to have one byte
coming out of the first fragment, 6 fragments, and one or more bytes coming
out of the last fragment. This gives us a total of 8 fragments
which exceeds what we can allow so we send such frames to be linearized.
Arguably the use of modulus might be more exact as the approach I propose
may generate some false positives. However the likelihood of us taking much
of a hit for those false positives is fairly low, and I would rather not
add more overhead in the case where we are receiving a frame composed of 4K
pages.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In an upcoming patch I would like to have access to the descriptor count
used for the data portion of the frame. For this reason I am splitting up
the descriptor count function from the function that stops the ring.
Also in order to try and reduce unnecessary duplication of code I am moving
the slow-path portions of the code out of being inline calls so that we can
just jump to them and process them instead of having to build them into
each function that calls them.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent changes should have enabled support for IPv6 based tunnels and
support for TSO with outer UDP checksums. As such we can update the
feature flags to reflect that.
In addition we can clean-up the flags that aren't needed such as SCTP and
RXCSUM since having the bits there doesn't add any value.
I also found one spot where we were setting the same flag twice. It looks
like it was probably a git merge error that resulted in the line being
duplicated. As such I have dropped it in this patch.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The XL722 has support for providing the outer UDP tunnel checksum on
transmits. Make use of this feature to support segmenting UDP tunnels with
outer checksums enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is mostly a minor clean-up for the Rx checksum path in order to avoid
some of the unnecessary conditional checks that were being applied.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add exception handling to the Tx checksum path so that we can handle cases
of TSO where the frame is bad, or Tx checksum where we didn't recognize a
protocol
Drop I40E_TX_FLAGS_CSUM as it is unused, move the CHECKSUM_PARTIAL check
into the function itself so that we can decrease indent.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch defers writing to the Tx descriptor bits until we know we have
successfully completed a given operation. So for example we defer updating
the tunnelling portion of the context descriptor until we have fully
identified the type.
The advantage to this approach is that we can assemble values as we go
instead of having to try and kludge everything together all at once. As a
result we can significantly clean up the tunneling configuration for
instance as we can just do a pointer walk and do the math for the distance
between each set of points.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for IPv6 extension headers in setting up the Tx
checksum. Without this patch extension headers would cause IPv6 traffic to
fail as the transport protocol could not be identified.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes two issues. First was the fact that iphdr(skb)->protocl
was being used to test for the outer transport protocol. This completely
breaks IPv6 support. Second was the fact that we cleared the flag for v4
going to v6, but we didn't take care of txflags going the other way. As
such we would have the v6 flag still set even if the inner header was v4.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Tx checksum path was maintaining a set of 3 pointers and two lengths in
order to prepare the packet for being checksummed. The thing is we only
really needed 2 pointers, and the lengths that were being maintained can
easily be computed.
As such we can replace the IPv4 and IPv6 header pointers with one single
union that represents both, or a generic pointer to the start of the
network header. For the L4 headers we can do the same with TCP and a
generic pointer to the start of the transport header. The length of the
TCP header is obtained by simply multiplying doff by 4, and the network
header length can be obtained by subtracting the network header pointer
from the transport header pointer.
While I was at it I renamed l4_hdr to l4_proto to make it a bit more clear
and less likely to be confused with l4.hdr which is the transport header
pointer.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch goes through and pulls all of the spots where we were updating
either the TCP or IP checksums in the TSO and checksum path into the TSO
function. The general idea here is that we should only be updating the
header after we verify we have completed a skb_cow_head check to verify the
head is writable.
One other advantage to doing this is that it makes things much more
obvious. For example, in the case of IPv6 there was one spot where the
offset of the IPv4 header checksum was being updated which is obviously
incorrect.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes it so that the L4 header offsets and such can be ignored
when dealing with the L3 checksum and length update. This is done making
use of two things.
First we can just use the offset from the L4 header to the start of the
packet to determine the L4 offset, and from that we can then make use of
the data offset to determine the full length of the headers.
As far as adjusting the checksum to remove the length we can simply add the
inverse of the length instead of having to recompute the entire
pseudo-header without the length. In the case of an IPv6 header this
should be significantly cheaper since we can make use of a value we already
needed instead of having to read the source and destination address out of
the packet.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of casing u32 values to u64 it makes more sense to just start out
with u64 values in the first place. This way we don't need to create a
mess with all of the casts needed to populate a 64b value.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e and i40evf drivers contained code for inserting an outer checksum
on UDP tunnels. The issue however is that the upper levels of the stack
never requested such an offload and it results in possible errors.
In addition the same logic was being applied to the Rx side where it was
attempting to validate the outer checksum, but the logic there was
incorrect in that it was testing for the resultant sum to be equal to the
header checksum instead of being equal to 0.
Since this code is so massively flawed, and doing things that we didn't ask
for it to do I am just dropping it, and will bring it back later to use as
an offload for SKB_GSO_UDP_TUNNEL_CSUM which can make use of such a
feature.
As far as the Rx feature I am dropping it completely since it would need to
be massively expanded and applied to IPv4 and IPv6 checksums for all parts,
not just the one that supports Tx checksum offload for the outer.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In MFP mode particularly when we were setting the PF VSI in limited
promiscuous, the HW switch was still mirroring the outgoing packets
from other VSIs (VF/VMdq) onto the PF VSI.
With this new bit set, the mirroring doesn't happen any more and so
we are in limited promiscuous on the PF VSI in MFP which is similar
to defport.
An API check is not required, since this bit is reserved for FW API
version < 1.5
Also update copyright year in file headers.
Change-ID: I9840cb95f11dde733d943cb03ce84f68b9611bc8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In one obscure corner case, it was possible to clear the NVM update wait
flag when no update_done message was actually received. This patch
cleans the event descriptor before use, and moves the opcode check to
where it won't get done if there was no event to clean.
Also update copyright year in file headers.
Change-ID: I68bbc41965e93f4adf07cbe98b9dfd63d41509a4
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a reset fails to complete, the driver gets its affairs in order and
awaits the cold solace of rmmod. Unfortunately, it was not properly
setting the adapter state, which would cause a panic on rmmod, instead
of the desired surcease.
Set the adapter state to DOWN in this case, and avoid a panic.
Change-ID: I6fdd9906da52e023f8dc744f7da44b5d95278ca9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the case where we have a page fully used by receive data, we need to
release the page fully to the stack. Instead of calling get_page (which
increments the page count) followed by free_page (which decrements the
page count), just donate our reference to the stack. Although this
donation is not tax deductible, it does allow us to avoid two very
expensive atomic operations that reverse each other.
Change-ID: If70739792d5748995fc175ec92ac2171ed4ad8fc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a workaround for cases where we might have
interrupts that got lost but WB happened.
If that happens without this patch we will see a tx_timeout.
To work around it, this patch goes ahead and reschedules NAPI
in that situation, if NAPI is not already scheduled.
We also add a counter in ethtool to keep track of when
we detect a case of tx_lost_interrupt.
Note: napi_reschedule() can be safely called from process/service_task
context and is done in other drivers as well without an issue.
Change-ID: I00f98f1ce3774524d9421227652bef20fcbd0d20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Support packet split receive on VFs. This is off by default but can be
enabled using ethtool private flags. Because we need to trigger a reset
from outside of i40evf_main.c, create a new function to do so, and
export it.
Also update copyright year in file headers.
Change-ID: I721aa5d70113d3d6d94102e5f31526f6fc57cbbb
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version to i40e-1.4.13 and i40evf-1.4.9
Change-ID: I9db37f9d4899141c3e5455dfb456d45465b8c035
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Get rid of the unused hsplit field in the ring struct and use the
existing macro to detect packet split enablement. This allows debugfs
dumps of the VSI to properly show which Rx routine is in use.
Change-ID: Ic4e9589e6a788ab196ed0850703f704e30c03781
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mr. Spock would certainly raise an eyebrow to see us using bitwise
operators, when we should clearly be relying on logic. Fascinating.
Change-ID: Ie338010c016f93e9faa2002c07c90b15134b7477
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor the packet split Rx code to properly use half-pages for
receives. The previous code was doing way more mapping and unmapping
than it needed to, and wasn't properly using half-pages.
Increment the page use count each time we give a half-page to an skb,
knowing that the stack will probably process and release the page before
we need it again. Only free and reallocate pages if the count shows that
both half-pages are in use. Add counters to track reallocations and page
reuse.
Change-ID: I534b299196036b64be82b4861a0a4036310a8f22
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e and i40evf drivers now cleanly handle allocation
failures and can avoid kernel log spew from the memory allocator
when allocations fail, so set __GFP_NOWARN on Rx buffer alloc.
Change-ID: Ic9e1b83c495e2a3ef6b069ba7fb6e52ce134cd23
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the "Don't Give Up" patch. Previously the
driver could fail an allocation, and then possibly stall
a queue forever, by never coming back to continue receiving
or allocating buffers.
With this patch, the driver will keep polling trying to allocate
receive buffers until it succeeds. This should keep all receive
queues running even in the face of memory pressure.
Also update copyright year in file header.
Change-ID: I2b103d1ce95b9831288a7222c3343ffa1988b81b
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While re-enabling interrupts the driver would clear all pending
causes. This meant that if an interrupt was generated while the driver
was cleaning or polling with interrupts disabled, then that interrupt
was lost. This could cause a queue to become dead, especially for
receive. Refactored the enable_icr0 function in order to allow
it to be decided by the caller whether the CLEARPBA (clear pending
events) bit will be set while re-enabling the interrupt.
Also update copyright year in file headers.
Change-ID: Ic1db100a05e13c98919057696db147a258ca365a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the driver string to 40-10 Gigabit instead of XL710/X710 for X722
and all future products.
Also update copyright year in file header.
Change-ID: I57fae656b36dc4eb682b2b7a054f8f48f3589149
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that the Force-WriteBack functionality in X710/XL710 devices
has been moved out of the clean routine and into the service task,
we need to make sure WriteBack-On-ITR is separated out since it
is still called from clean.
In the X722 devices, Force-WriteBack implies WriteBack-On-ITR but
without the interrupt, which put the driver into a missed
interrupt scenario and a potential tx-timeout report.
With this patch, we break the two functions out, and call the
appropriate ones at the right place. This will avoid creating missed
interrupt like scenarios for X722 devices.
Also update copyright year in file headers.
Change-ID: Iacbde39f95f332f82be8736864675052c3583a40
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't bother trying to set up a TSO if the skb->ip_summed is not
set to CHECKSUM_PARTIAL.
Change-ID: I6495b3568e404907a2965b48cf3e2effa7c9ab55
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver was using an offset based off a DMA handle while mapping and
unmapping using sync_single_range_for[cpu|device], where it should
be using DMA handle (returned from alloc_coherent) and the offset of the
memory to be sync'd.
Change-ID: I208256565b1595ff0e9171ab852de06b997917c6
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Nelson, Shannon <shannon.nelson@intel.com>
Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF is reset via VFLR, the device will be knocked out of bus
master mode, and the driver will fail to recover from the reset. Fix
this by enabling bus mastering after every reset. In a non-VFLR case,
the bus master bit will not be disabled, and this call will have no effect.
Change-ID: Id515859ac7a691db478222228add6d149e96801a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were not doing write-back on interrupt throttle for Legacy case in X722.
This patch fixes that, so we do WB_ON_ITR for Legacy as well. Plus the issue
that we should still be setting NO_ITR if we are touching the DYN_CTLN register
since we do not want to change ITR setting here.
Change-ID: I5db8491ee1544118a389db839cecc93e1bbc480e
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump AQ minor version to 1.5 for new FW features.
Change-ID: I5a790f7f519a2a8921aaa1c5663727dd1897ffec
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the new AQ command and struct for managing a thermal sensor.
Change-ID: I6f5631839a0f3dca352a6c222f1269a960e2310a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the new Cisco VXLAN-GPE cloud tunnel type for the Add Cloud Filter
and UDP tunnel AQ commands.
Change-ID: I2c093c7d79726c7fca08a36e5c63581a905da3d2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the new Set Switch Config AdminQ command, and mark the L2 Filter
bit as deprecated in the Add VEB command.
Change-ID: I5b24790f14c56f0ddf3f70df1e486844146b039f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add flags to MAC allocation requests to signify that the MAC VLAN filters
should come from the shared resource pool rather than the dedicated PF
resource pools.
Change-ID: I4c2da64c01856edcb0982bc4aab75c5a91047a7a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the new External Device Power Ability field to the get_link_status data
structure, using space from the reserved field at the end of the struct.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the name of the new cloud tunnel type from the place-holder NGE
name to the official Geneve. Also fix the spelling of the VXLAN type.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Add the AQ opcode and struct definitions for the Run PHY Activity command
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the new proxy-wake-on-lan capability bit available with the
new X722 device.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jesse Brandeburg