Shut up sparse warnings by making GPIO_IRQ_MASK unisgned
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Set up the IRQ line for the WM9713 device on the Zylonite.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-tosa.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert set/reset_scoop_gpio to generic gpio calls.
This patch depends on the pxaficp_ir hooks patch.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SPI information got placed in the middle of the SMC91x data.
Lets move it up a few lines so that we keep related things grouped
together.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
TOSA_GPIO_ON_KEY can't wakeup the device. But the board
provides TOSA_GPIO_POWERON which is OR of (on_ac) and (on_button).
Use it for wake up.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Although the GPIO alternate functions should be correctly set
by the bootloader, configure them here to be sure.
To save power, FFUART/BTUART/STUART are left unconfigured (output, low)
until they are needed by pxaficp or the magician GSM chipset driver.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch enables LEDs and the 1-wire bus (connected to
a DS2760 battery monitor) on the magician.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a call to pxa_set_i2c_info() to force i2c registration
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clean up all pins configuration to use currently proposed MFP table
schema.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All magician devices I've encountered so far have featured the Toppoly
TD028STEB1 display, so the Samsung LTP280QV support is untested.
The power-on sequence is not correct because pxafb doesn't yet support
enabling the LCD controller in the middle of the it.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This enables rootfs on StrataFlash if the bootloader supplies the
partition list.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
needed for power management (audio, BT, charging, GSM, LCD, SD), GSM, flash and SD operation and audio routing.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since recent PXA changes the (non-power-)I2C bus has to be explicitly
enabled from board initialisation code.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PXA3xx will not suspend if there are no wakeup sources configured.
Print a diagnostic message to make it easier for the user to see what's
happening.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mainstone has the primary I2C bus exposed for use on plugin modules.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch implements support for Gumstix-F flash, udc and mci. Fixes since the last time are:
- Steve Sakoman as maintainer
- cleanup for udc and mci setup
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is partial because mainstone's keypad is really special, some of
the keys like '1', '2', ... are actually connected to two row/column
juntions, thus pressing '1' is equivalent to pressing 'A' & 'H'.
This is really brain damanged since it makes distinguishing between
pressing '1' and multiple keys pressing of 'A' & 'H' difficult.
So these special keys are not supported for the time being.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
also update the clk definitions in pxa27x and pxa3xx.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
NOTE: currently don't know if the key code of KEY_SUSPEND is fit for
such usage.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Changes include:
1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate
the board capability of this pin to wakeup the system
2. add gpio_set_wake() and keypad_set_wake() to allow dynamically
enable/disable wakeup from GPIOs and keypad GPIO
* these functions are currently kept in mfp-pxa2xx.c due to their
dependency to the MFP configuration
3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP
is set on incorrect pins
So that the GPIO's wakeup capability is now decided by the following:
a) processor's capability: (only those GPIOs which have dedicated
bits within PWER/PRER/PFER can wakeup the system), this is
initialized by pxa{25x,27x}_init_mfp()
b) board design decides:
- whether the pin is designed to wakeup the system (some of
the GPIOs are configured as other functions, which is not
intended to be a wakeup source), by OR'ing the pin config
with MFP_LPM_CAN_WAKEUP
- which edge the pin is designed to wakeup the system, this
may depends on external peripherals/connections, which is
totally board specific; this is indicated by MFP_LPM_EDGE_*
c) the corresponding device's (most likely the gpio_keys.c) wakeup
attribute:
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. the following code to configure PGSRx is no way portable and
intuitive:
- PGSR0 = 0x00008800;
- PGSR1 = 0x00000002;
- PGSR2 = 0x0001FC00;
- PGSR3 = 0x00001F81;
this is removed as low power state has already been encoded in
the pin configuration definitions.
Note: there is no specific reason for some of the GPIOs to drive
high in low power mode as indicated by the above setting, those
bits are ignored, and the result is validated to work.
2. the following code to configure GPIO wakeup is removed as this
is now totally handled by pxa2xx_mfp_config():
- PWER = 0xC0000002;
- PRER = 0x00000002;
- PFER = 0x00000002;
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs. A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.
A pin configuration on pxa{25x,27x} is composed of:
- alternate function selection (or pin mux as commonly called)
- low power state or sleep state
- wakeup enabling from low power mode
The following MFP_xxx bit definitions in mfp.h are re-used:
- MFP_PIN(x)
- MFP_AFx
- MFP_LPM_DRIVE_{LOW, HIGH}
- MFP_LPM_EDGE_*
Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:
- MFP_CFG_IN : for input alternate functions
- MFP_CFG_OUT : for output alternate functions
Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT(). As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.
Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output. The actual
direction of the GPIO is configured by gpio_direction_{input, output}
Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.
E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:
enable_irq_wake( gpio_to_irq(35) );
To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).
Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:
- MFP_LPM_WAKEUP_ENABLE
The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:
- WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
- WAKEUP_ON_LEVEL_HIGH
The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.
These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.
The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
two reasons:
1. GPIO namings and their mode definitions are conceptually not part
of the PXA register definitions
2. this is actually a temporary move in the transition of PXA2xx to
use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
code will still work and new code can be added in step by step
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MFP configurations after resume should be done before the GPIO registers
are restored. Move the mfp sysdev registeration to the same place where
GPIO and IRQ sysdev(s) are registered to better control the order.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The main issue here is that pxa3xx does not have GAFRx registers,
access directly to these registers should be avoided for pxa3xx:
1. introduce __gpio_is_occupied() to indicate the GAFRx and GPDRx
registers are already configured on pxa{25x,27x} while returns
0 always on pxa3xx
2. pxa_gpio_mode(gpio | GPIO_IN) is replaced directly with assign-
ment of GPDRx, the side effect of this change is that the pin
_must_ be configured before use, pxa_gpio_irq_type() will not
change the pin to GPIO, as this restriction is sane, esp. with
the new MFP framework
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To further clean up the GPIO and IRQ structure:
1. pxa_init_irq_gpio() and pxa_init_gpio() combines into a single
function pxa_init_gpio()
2. assignment of set_wake merged into pxa_init_{irq,gpio}() as
an argument
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes the code better organized and simplified a bit. The change
will lose a bit of performance when performing IRQ ack/mask/unmask,but
that's not too much after checking the result binary.
This patch also removes the ugly #ifdef CONFIG_PXA27x .. #endif by
carefully not to access those pxa{27x,3xx} specific registers, this
is done by keeping an internal IRQ number variable. The pxa-regs.h
is also modified so registers for IRQ > PXA_IRQ(31) are made public
even if CONFIG_PXA{27x,3xx} isn't defined (for pxa25x's sake)
The incorrect assumption in the original code that internal irq starts
from 0 is also corrected by comparing with PXA_IRQ(0).
"struct sys_device" for the IRQ are reduced into one single device on
pxa{27x,3xx}.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
by
1. wrapping long lines and making comments tidy
2. using IRQ_TYPE_* instead of migration macros __IRQT_*
3. introduce a pr_debug() for the commented printk(KERN_DEBUG ...)
stuff
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
by:
1. introduce dedicated pxa_{mask,unmask}_low_gpio()
2. remove set_irq_chip(IRQ_GPIO_2_x, ...) which has already been
initialized in pxa_init_irq()
3. introduce dedicated pxa_init_gpio_set_wake()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. As David Brownell suggests, using ffs() is going to make the loop
a bit faster (by avoiding unnecessary shift and iteration)
2. Russell suggested find_{first,next}_bit() being used with the
gedr[] array
Signed-off-by: eric miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AC97 clock rate on PXA3xx is generated with a configurable divider
from sys_pll.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Expose control of the PXA3xx 13MHz CLK_POUT pin via the clock API
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is unnecessary since it is already protected by
spin_lock_irq{save, restore} in clock.c.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert debug-only (and removed) MODULE_PARM() to module_param().
Compiles cleanly (with DEBUG=1).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The .get method is needed for suspend/resume. Otherwise you
get this in dmesg:
cpufreq: suspend failed to assert current frequency is what timing core thinks it is.
cpufreq: resume failed to assert current frequency is what timing core thinks it is.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that the clock lookup always finds an entry for a specific
device and ID before it falls back to finding just by ID. This
fixes a problem reported by Holger Schurig where the BTUART was
assigned the wrong clock.
Tested-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to PXA300/310 and PXA320 Developer manuals,
the ASCR[RDH] "bit needs to be cleared as part of the software
initialization coming out of any reset and coming out of D3".
The latter requirement is addressed by commit
"c4d1fb627ff3072", as for the former (coming out of any reset),
the kernel relies on boot loaders and assumes that RDH bit
is cleared there. Though, not all bootloaders follow the rule
so we have to clear the bit in kernel.
We clear the RDH bit in pxa3xx_init() function since
it is always invoked after any reset. We also preserve D1S, D2S
and D3S bits from being cleared in case we invoke pxa3xx_init()
function not from normal hardware reset (e.g. kexec scenario),
so these bits can be properly referenced later.
Signed-off-by: Dmitry Krivoschekov <dmitry.krivoschekov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds gpiolib support for the PXA architecture:
- move all GPIO API functions from generic.c into gpio.c
- convert the gpio_get/set_value macros into inline functions
This makes it easier to hook up GPIOs provided by external chips like
ASICs and CPLDs.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Minor ARM fixup from David Brownell folded into this ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
...
This patch adds a PXA2xx specific header file to control chip setup.
Without, the PCM027 BSP can't be built.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The is caused by the patch below:
[ARM] 4737/1: Refactor corgi_lcd to improve readability + bugfix
It renamed the confusing get_hsync_len() to get_hsync_invperiod(), which
unfortunately leaves poodle.c un-modified.
Signed-off-by: eric miao <eric.miao@marvell.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some machines are missing "pxa2xx-regs.h" due to the following patch:
[ARM] pxa: move memory controller registers into pxa2xx-regs.h
This patch fixes the issue by including the pxa2xx-regs.h where necessary.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce a sysdev for pxa3xx static memory controller, mainly
for register saving/restoring in PM
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. clear RDH bit after resuming back from D3, otherwise, the multi function
pins will retain the low power state
2. save/restore essential system registers
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The header file <asm/arch/ohci.h> was missing in the original file,
include it to fix the warning.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use gpio_vbus instead of udc_is_connected for udc on tosa.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for Toradex' PXA27x based Colibri module.
It's kept as simple as possible to only provide basic functionality.
A default config is also included.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix all those PXA mci_init functions which return -1 rather than
propagating the error code to the higher levels. Remove the silly
set_irq_type() calls as well - use the flags for request_irq()
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch refactors the code in corgi_lcd.c moving it to the board
specific corgi and spitz files where appropriate instead of the
existing ifdef mess which hinders readability.
Fix spitz_get_hsync_len() to call get_hsync_invperiod so pxafb can be
compiled as a module.
The confusing variables which represent the inverse horizintal sync
period are renamed to "invperiod" consistently.
An incorrect comment in corgi_ts.c is also corrected.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds baseboard support for the phyCORE-PXA270 development
kit (aka PCM-990).
This example shows how to use some phyCORE-PXA270 CPU module features
on a baseboard in a standard manner. It could be used as a starting
point for custom baseboard development.
V2:
After comments by Eric Miao:
- IRQ chained handler fixed
- video/graphic support moved to separate patch
- ifdef/endif hell reduced ;-)
V3:
After comments by Russell King
- initialise the mmci platform data statically
V4:
After comments by Russell King
- wrong return value in pcm990_mci_init() fixed
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds main support for the generic phyCORE-PXA270 CPU module
(aka PCM-027). Its as generic as possible to support any kind of baseboard.
Note: Neither the CPU module nor the pcm027.c implementation can work without
a baseboard support. Baseboard support can be added by the PCM-990 or any
custom variant.
V2:
After comments by Eric Miao:
- Currently unsupported devices moved into separate patch
- direct call of baseboard initialisation
V3:
After comments by Russell King
- sort include files
- setting RTC bit for power control removed
- style problems fixed (discovered by checkpatch.pl)
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
smc91x is shared between many different platforms. Each platform needs
to specify the interrupt type, and in some cases the irq type depends
on more than just the build configuration - it depends on runtime
checks.
Rather than throwing this code into the SMC_IRQ_FLAGS definition, provide
a way for these flags to be passed via the IRQ resource itself.
Note that IRQF_TRIGGER_* constants are intentionally defined to correspond
with the IORESOURCE_IRQ_* interrupt type flags, in much the same way that
the low bits of PCI iomem resources correspond with the BAR flag bits.
Also provide a way to configure smc91x to read the IRQ flags from the
resource. Once all platforms have been converted over (signified
by all definitions of SMC_IRQ_FLAGS being -1) SMC_IRQ_FLAGS should
be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
This includes irda, gpio keys, pxafb, backlight, ohci and flash
(read-only).
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch contains the base code to boot the Toshiba e330, e740,
e750, e400, and e800 PDAs.
Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds back the registration of HWUART clock on pxa25x
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The original code incorrectly returns Hz instead of KHz.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add polling I2C transfer implementation for PXA I2C. This is needed
for cases where I2C transactions have to occur at times interrups are
disabled.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
registers are retained during standby mode, thus it's not necessary
to save/restore and checksum
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When PXA27x wakes up, tick_resume_oneshot() tries to set a timer
interrupt to occur immediately. Since PXA27x requires at least
MIN_OSCR_DELTA, this causes us to flag an error.
tick_program_event() then increments the next event time by
min_delta_ns. However, by the time we get back to programming
the next event, the OSCR has incremented such that we fail again.
We repeatedly retry, but the OSCR is too fast for us - we never
catch up, so we never break out of the loop - resulting in us
never apparantly resuming.
Fix this by doubling min_delta_ns.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PXA manuals indicate that when in standby or sleep modes, clocks to
peripherals are shut off by the processor itself. Eg:
PXA270 standby: "In standby mode, all clocks are disabled except those
for the power manager and the RTC."
PXA270 sleep: "In sleep mode, all clocks are disabled to the processor
and to all peripherals except the RTC."
PXA255 sleep: "In Sleep Mode, all processor and peripheral clocks are
disabled, except the RTC."
Therefore, it should be safe to leave the clock enable register alone
prior to entering low power modes for these SoCs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Wakeup sources on PXA3 are enabled at two levels. First, the MFP
configuration has to be set to enable which edges a specific pin
will trigger a wakeup. The pin also has to be routed to a functional
unit. Lastly, the functional unit must be enabled as a wakeup source
in the appropriate AD*ER registers (AD2D0ER for standby resume.)
This doesn't fit well with the IRQ wake scheme - we currently do a
best effort conversion from IRQ numbers to functional unit wake enable
bits. For instance, there's several USB client related enable bits but
there's no corresponding IRQs to determine which you'd want. Conversely,
there's a single enable bit covering several functional units.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hook the MFP code into the power management code so that the MFPs can
be reconfigured when suspending and resuming. However, note the FIXME
- low power mode MFP configuration may depend on the system state being
entered.
Also note that we have to clear any detected edge events prior to
entering a low power mode - otherwise we immediately wake up.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are two reasons for making the MFP configuration to be processor
independent, i.e. removing the relationship of configuration bits with
actual MFPR register settings:
1. power management sometimes requires the MFP to be configured
differently when in run mode or in low power mode
2. for future integration of pxa{25x,27x} GPIO configurations
The modifications include:
1. introducing of processor independent MFP configuration bits, as
defined in [include/asm-arm/arch-pxa/mfp.h]:
bit 0.. 9 - MFP Pin Number (1024 Pins Maximum)
bit 10..12 - Alternate Function Selection
bit 13..15 - Drive Strength
bit 16..18 - Low Power Mode State
bit 19..20 - Low Power Mode Edge Detection
bit 21..22 - Run Mode Pull State
and so on,
2. moving the processor dependent code from mfp.h into mfp-pxa3xx.h
3. cleaning up of the MFPR bit definitions
4. mapping of processor independent MFP configuration into processor
specific MFPR register settings is now totally encapsulated within
pxa3xx_mfp_config()
5. using of "unsigned long" instead of invented type of "mfp_cfg_t"
according to Documentation/CodingStyle Chapter 5, usage of this
in platform code will be slowly removed in later patches
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa3xx_mfp_set_xxx() functions are originally provided for overwriting
MFP configurations performed by pxa3xx_mfp_config(), the usage of such
a dirtry trick is not recommended, since there is currently no user of
these functions, they are safely removed
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PXA3 has a different memory controller from PXA2 platforms. Avoid
clashing definitions by moving the PXA2 definitions to pxa2xx-regs.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mapping for physical address 0x48000000 is not sufficient
to allow access to the dynamic memory controller configuration
registers on PXA3. These registers need to be accessed to
reconfigure the SDRAM when waking from a low power mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to add the third mmc controller support _only_
for pxa310.
On zylonite, the third controller support one slot.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to add the second mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.
On zylonite, the second controller has no slot.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patchis to add the first mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.
On zylonite, the first controller supports two slots, this patch
only support the first one right now.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Considering that generic.c is getting more and more bloated by device
information, moving that part out side will be much cleaner.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to move pxamci DMA specific code to corresponding
platform layer because using DRCMRRXMMC/DRCMRTXMMC in pxamci.c makes
the driver code dedicated to platform which is not extensible.
It is applicable to all pxa platforms.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There have been patches hanging around for ages to add support for
cpufreq to PXA255 processors. It's about time we applied one.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initialise the SSP driver at arch_initcall() time, so it's available
for other drivers to use it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only register the "cpld_irq" sysclass for mainstone/lubbock if we're
running on one of those platforms.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. make pxa2xx_spi.c use ssp_request() and ssp_free() to get the common
information of the designated SSP port.
2. remove those IRQ/memory request code, ssp_request() has done that for
the driver
3. the SPI platform device is thus made psuedo, no resource (memory/IRQ)
has to be defined, all will be retreived by ssp_request()
4. introduce ssp_get_clk_div() to handle controller difference in clock
divisor setting
5. use clk_xxx() API for clock enable/disable, and clk_get_rate() to
handle the different SSP clock frequency between different processors
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. change SSP register definitions from absolute virtual addresses to
offsets
2. use __raw_writel()/__raw_readl() for functions of ssp_xxxx()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. define "struct ssp_device" for SSP information, which is requested
and released by function ssp_request()/ssp_free()
2. modify the ssp_init() and ssp_exit() to use the interface
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OSCR is supposed to monotonically increment; however restoring it
to a time prior to OSMR0 may result in it being wound backwards.
Instead, if OSMR0 is within the minimum expiry time, wind OSMR0
forwards.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Apparantly, the generic time subsystem can accurately emulate periodic
mode via the one-shot support code, so we don't need our own periodic
emulation code anymore. Just ensure that we build support for one shot
into the generic time subsystem.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linux has framebuffer backlight support infrastructure which should
be used to expose backlight attributes. Mainstone should use it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only register the MMC, framebuffer, I2C and FICP devices when the
platform supplies the necessary platform data structures for the
devices.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add keyboard support on tosa (Sharp Zaurus SL-6000x).
Largely based on patches by Dirk Opfer.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
r2 is not guaranteed to be preserved over a function call, so relying
on it to store the link register over the call to sleep_phys_sp() is
unreliable. Store the link register on the stack instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suspend/resume on the pxa25x was fairly obviously broken in revision
711be5ccfe.
This patch fixes the damage by adding back the missing code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change printk to dev_dbg in ITE 8152 driver and remove printk in ITE 8152 ISR.
Move PCI intialization from ->scan to ->preinit method
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: bridge wu <bridge.wu@marvell.com>
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CKEN_USBHOST should be used instead of CKEN_USB for usb host
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PXA3xx uses its own clk_pxa3xx_cken_ops, modify the code to use the
PXA3xx specific macros to define its clocks
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
One-shot timer mode on PXA has various bugs which prevent kernels
build with NO_HZ enabled booting. They end up spinning on a
permanently asserted timer interrupt because we don't properly
clear it down - clearing the OIER bit does not stop the pending
interrupt status. Fix this in the set_mode handler as well.
Moreover, the code which sets the next expiry point may race with
the hardware, and we might not set the match register sufficiently
in the future. If we encounter that situation, return -ETIME so
the generic time code retries.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Resolve:
CC arch/arm/mach-pxa/time.o
arch/arm/mach-pxa/time.c: In function `pxa_osmr0_set_mode':
arch/arm/mach-pxa/time.c:154: warning: enumeration value `CLOCK_EVT_MODE_RESUME' not handled in switch
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a typo in MFP address map.
Signed-off-by: Aleksey Makarov <amakarov@ru.mvista.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The name of 'struct pm_ops' suggests that it is related to the power
management in general, but in fact it is only related to suspend. Moreover,
its name should indicate what this structure is used for, so it seems
reasonable to change it to 'struct platform_suspend_ops'. In that case, the
name of the global variable of this type used by the PM core and the names of
related functions should be changed accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the definition of 'struct pm_ops' and related functions from <linux/pm.h>
to <linux/suspend.h> .
There are, at least, the following reasons to do that:
* 'struct pm_ops' is specifically related to suspend and not to the power
management in general.
* As long as 'struct pm_ops' is defined in <linux/pm.h>, any modification of it
causes the entire kernel to be recompiled, which is unnecessary and annoying.
* Some suspend-related features are already defined in <linux/suspend.h>, so it
is logical to move the definition of 'struct pm_ops' into there.
* 'struct hibernation_ops', being the hibernation-related counterpart of
'struct pm_ops', is defined in <linux/suspend.h> .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch provides core support for CM-X270 platform.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa_gpio_mode() is a universal call that fiddles with the GAFR
(gpio alternate function register.) GAFR does not exist on PXA3
CPUs, but instead the alternate functions are controlled via the
MFP support code.
Platforms are expected to configure the MFP according to their
needs in their platform support code rather than drivers. We
extend this idea to the GAFR, and make the gpio_direction_*()
functions purely operate on the GPIO level.
This means platform support code is entirely responsible for
configuring the GPIOs alternate functions on all PXA CPU types.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
a function pxa_init_irq_set_wake() was introduced, so that
processor specific code could install their own version
code setting PFER and PRER registers within pxa_gpio_irq_type
are removed, and the edge configuration is postponed to the
(*set_wake) and copies the GRER and GFER register, which will
always be set up correctly by pxa_gpio_irq_type()
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This definition produces processor specific code in generic function
pxa_gpio_mode(), thus creating inconsistencies for support of pxa25x
and pxa27x in a single zImage.
As David Brownell suggests, make it a run-time variable and initialize
at run-time according to the number of GPIOs on the processor. For now
the initialization happens in pxa_init_irq_gpio(), since there is
already a parameter for that, besides, this is and MUST be earlier
than any subsequent calls to pxa_gpio_mode().
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the generic clock support code to fiddle with the CKEN register
and mark pxa_set_cken() deprecated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
get_lcdclk_frequency_10khz() is now redundant, remove it. Hide
pxa27x_get_lcdclk_frequency_10khz() from public view.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename pxa25x and pxa27x memory/lcd/core clock functions, and
select the correct version at run time.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than using the compile-time constant CLOCK_TICK_RATE, select
the clock tick rate at run time. We organise the selection so that
PXA3 automatically falls out with the right tick rate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The previous implementation was relying on compile time optimizations
based on a constant clock rate. However, support for different PXA
flavors in the same kernel binary requires that the clock be selected at
run time, so here it is.
Let's move this code to a more appropriate location while at it.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the corgi backlight driver to a more generic version
so it can be reused by other code rather than being Zaurus/PXA
specific.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
As pointed out by Jrgen, we are overflowing the number of GPIOs
in pxa_init_irq_gpio(). I'm seeing the same problem on my HTC
Universal PXA270 based PDA.
According to Eric, the function argument is the number of GPIOs,
so we should keep the semantics and reduce the number of
iteration by 1.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Jrgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reimplements arch/arm/mach-pxa/time.c using a clock_event_device based
on OSMR0. Tested on PXA270, linux-2.6.22+arm:pxa patches.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. split pxa_cpu_suspend to pxa25x_cpu_suspend and pxa27x_cpu_suspend
and make pxa25x_cpu_pm_enter() and pxa27x_cpu_pm_enter() to invoke
the corresponding _suspend functions, thus remove all those ugly
#ifdef .. #endif out of sleep.S
2. move the declarations of those suspend functions to pm.h
note: this is not a clean enough solution until all the pxa25x and
pxa27x specific part is further removed out of sleep.S, sleep.S is
supposed to contain generic code only
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. introduce a structure pxa_cpu_pm_fns for pxa25x/pxa27x specific
operations as follows:
struct pxa_cpu_pm_fns {
int save_size;
void (*save)(unsigned long *);
void (*restore)(unsigned long *);
int (*valid)(suspend_state_t state);
void (*enter)(suspend_state_t state);
}
2. processor specific registers saving and restoring are performed
by calling the corresponding (*save) and (*restore)
3. pxa_cpu_pm_fns->save_size should be initialized to the required
size for processor specific registers saving, the allocated
memory address will be passed to (*save) and (*restore)
memory allocation happens early in pxa_pm_init(), and save_size
should be assigned prior to this (which is usually true, since
pxa_pm_init() happens in device_initcall()
4. there're some redundancies for those SLEEP_SAVE_XXX and related
macros, will be fixed later, one way possible is for the system
devices to handle the specific registers saving and restoring
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. for common devices across all the pxa variants, the names
are changed to be:
"pxa_device_xxx"
2. for pxa25x or pxa27x specific devices, the names are
changed to be:
"pxa25x_device_xxx", or
"pxa27x_device_xxx"
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows individual CPU support to determine which platform
devices should be registered. Also fix a copy-n-paste bug in
the I2C power platform device entry.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The RTC library code contains everything necessary to set the
system time from the RTC; for similar reasons as the previous
commit, it's far better to let the RTC library code sort this
out rather than implement something which might not be
appropriate for everyone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the RTC management over a suspend/resume cycle. Firstly,
we may not be using the internal RTC for time keeping; some
platforms have an external RTC for this inspite of the PXA having
an internal RTC. Secondly, the RTC library code handles updating
system time on resume.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the number of dma channels varies between pxa25x and pxa27x, it
introduces some specific code in dma.c. This patch moves the specific
code to pxa25x.c and pxa27x.c and makes dma.c more generic.
1. add pxa_init_dma() for dma initialization, the number of channels
are passed in by the argument
2. add a "prio" field to the "struct pxa_dma_channel" for the channel
priority, and is initialized in pxa_init_dma()
3. use a general priority comparison with the channels "prio" field so
to remove the processor specific pxa_for_each_dma_prio macro, this
is not lightning fast as the original one, but it is acceptable as
it happens when requesting dma, which is usually not so performance
critical
Signed-off-by: eric miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
/* should be ok this time, I aligned this patch to your arm:pxa2.mbox */
1. move pxa25x specific IRQ initialization code to pxa25x_init_irq()
and pxa27x code to pxa27x_init_irq(), remove pxa_init_irq()
2. replace all pxa_init_irq() with their PXA25x or PXA27x specific
functions
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. use GPIO_IRQ_mask[] to select those bits of interest, actually
only those "unmasked" GPIO IRQs with their corresponding bits
in GPIO_IRQ_mask[] set to "1" should be checked
2. remove #ifdef PXA_LAST_GPIO > 96 .. #endif, GPIO_IRQ_mask[]
is used to mask out the irrelevant bits, so that even though
the GEDR3 on PXA25x is reserved, it will be masked, and the
following code will never run. Another point is that GPIO85-
GPIO95 bits within GEDR2 will also be masked out on PXA25x
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
move the GPIO IRQ initialization code to pxa_init_irq_gpio()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. move low IRQ initialization code to pxa_init_irq_low()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. define PXA_GPIO_IRQ_BASE to be right after the internal IRQs,
and define PXA_GPIO_IRQ_NUM to be 128 for all PXA2xx variants
2. make the code specific to the high IRQ numbers (32..64) to be
PXA27x specific
3. add a function pxa_init_irq_high() to initialize the internal
high IRQ chip, the invoke of this function could be moved to
PXA27x specific initialization code
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. PXA_IRQ_SKIP is defined to be 7 on PXA25x so that the first IRQ
starts from zero. This makes IRQ numbering inconsistent between
PXA25x and PXA27x. Remove this macro so that the same IRQ_XXXXX
definition has the same value on both PXA25x and PXA27x.
2. make IRQ_SSP3..IRQ_PWRI2C valid only if PXA27x is defined, this
avoids unintentional use of these macros on PXA25x
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa_pm_prepare() tried to validate the suspend method type. As
noted in previous commits:
eb9289eb209c372d06cee8c9c50269
the checking of the suspend type in the 'prepare' method is the
wrong place to do this; use the 'valid' method instead. This
means that pxa_pm_prepare() can be entirely removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the pm_ops structure into the PXA25x and PXA27x support
files. Remove the old pxa_pm_prepare() function, and rename
the both pxa_cpu_pm_prepare() functions as pxa_pm_prepare().
We'll fix that later.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa_pm_finish() does nothing but return zero. The core code
does nothing with this return value, and will not try to call
the finish method in the pm_ops structure if it is NULL.
Therefore, we can remove this useless function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PXA CKEN changes broken syspend/resume on the pxa27x. This patch
corrects the problem and fixes another couple of bad references.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This update for trizeps4 SoM contains:
- support for new TFT on more recent ConXS evalboard
- correct partition of flash device
- update of "trizeps4_defconfig"
Signed-off-by: Jrgen Schindele (linux@schindele.name)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add IRQF_IRQPOLL for each timer interrupt.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Almost all users of pm_ops only support mem sleep, don't check in .valid and
don't reject any others in .prepare so users can be confused if they check
/sys/power/state, especially when new states are added (these would then
result in s-t-r although they're supposed to be something different).
This patch implements a generic pm_valid_only_mem function that is then
exported for users and puts it to use in almost all existing pm_ops.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: linux-pm@lists.linux-foundation.org
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series cleans up some misconceptions about pm_ops. Some users of
the pm_ops structure attempt to use it to stop the user from entering suspend
to disk, this, however, is not possible since the user can always use
"shutdown" in /sys/power/disk and then the pm_ops are never invoked. Also,
platforms that don't support suspend to disk simply should not allow
configuring SOFTWARE_SUSPEND (read the help text on it, it only selects
suspend to disk and nothing else, all the other stuff depends on PM).
The pm_ops structure is actually intended to provide a way to enter
platform-defined sleep states (currently supported states are "standby" and
"mem" (suspend to ram)) and additionally (if SOFTWARE_SUSPEND is configured)
allows a platform to support a platform specific way to enter low-power mode
once everything has been saved to disk. This is currently only used by ACPI
(S4).
This patch:
The pm_ops.pm_disk_mode is used in totally bogus ways since nobody really
seems to understand what it actually does.
This patch clarifies the pm_disk_mode description.
It also removes all the arm and sh users that think they can veto suspend to
disk via pm_ops; not so since the user can always do echo shutdown >
/sys/power/disk, they need to find a better way involving Kconfig or such.
ACPI is the only user left with a non-zero pm_disk_mode.
The patch also sets the default mode to shutdown again, but when a new pm_ops
is registered its pm_disk_mode is selected as default, that way the default
stays for ACPI where it is apparently required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that
CKEN0_PWM0 --> CKEN_PWM0
CKEN1_PWM1 --> CKEN_PWM1
...
CKEN24_CAMERA --> CKEN_CAMERA
The reasons for the change of these defitions are:
1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24
2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for
3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off
Another change in the patch is to make the definitions equal to its
clock bit index, so that
#define CKEN_CAMERA (24)
instead of
#define CKEN_CAMERA (1 << 24)
this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Lots of places in arch/arm were needlessly including linux/ptrace.h,
resumably because we used to pass a struct pt_regs to interrupt
handlers. Now that we don't, all these ptrace.h includes are
redundant.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix tosa compile failure from commit
32f3f49910
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based on the discussion last december (http://lkml.org/lkml/2006/12/20/242),
this patch:
- moves the PXA_LAST_GPIO check into pxa_gpio_mode
- fixes comment and includes in gpio.h
- replaces the gpio_set/get_value macros with inline
functions and adds a non-inline version to avoid
code explosion when gpio is not a constant.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits)
[ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports
[ARM] 4140/1: AACI stability add ac97 timeout and retries
[ARM] 4139/1: AACI record support
[ARM] 4138/1: AACI: multiple channel support for IRQ handling
[ARM] 4211/1: Provide a defconfig for ns9xxx
[ARM] 4210/1: base for new machine type "NetSilicon NS9360"
[ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM
[ARM] 4221/1: S3C2443: DMA support
[ARM] 4220/1: S3C24XX: DMA system initialised from sysdev
[ARM] 4219/1: S3C2443: DMA source definitions
[ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443
[ARM] 4217/1: S3C24XX: remove the dma channel show at startup
[ARM] 4090/2: avoid clash between PXA and SA1111 defines
[ARM] 4216/1: add .gitignore entries for ARM specific files
[ARM] 4214/2: S3C2410: Add Armzone QT2410
[ARM] 4215/1: s3c2410 usb device: per-platform vbus_draw
[ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST
[ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos
[ARM] 4137/1: Add kexec support
[ARM] 4201/1: SMP barriers pair needed for the secondary boot process
...
Fix up conflict due to typedef removal in sound/arm/aaci.h
Fixup the is_contionous replacement by a flag field.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch the i2c-pxa driver to actually using the platform device information and let it handle the power i2c bus on pxa27x too. Original version of this patch didn't compile with CONFIG_I2C_PXA_SLAVE set.
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4017/1: [Jornada7xx] - Updating Jornada720.c
[ARM] 3992/1: i.MX/MX1 CPU Frequency scaling support
[ARM] Provide a method to alter the control register
[ARM] 4016/1: prefetch macro is wrong wrt gcc's "delete-null-pointer-checks"
[ARM] Remove empty fixup function
[ARM] 4014/1: include drivers/hid/Kconfig
[ARM] 4013/1: clocksource driver for netx
[ARM] 4012/1: Clocksource for pxa
[ARM] Clean up ioremap code
[ARM] Unuse another Linux PTE bit
[ARM] Clean up KERNEL_RAM_ADDR
[ARM] Add sys_*at syscalls
[ARM] 4004/1: S3C24XX: UDC remove implict addition of VA to regs
[ARM] Formalise the ARMv6 processor name string
[ARM] Handle HWCAP_VFP in VFP support code
[ARM] 4011/1: AT91SAM9260: Fix compilation with NAND driver
[ARM] 4010/1: AT91SAM9260-EK board: Prepare for MACB Ethernet support
Add a clocksource driver for pxa2xx systems
Signed-off-by: Luotao Fu <lfu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Standardize the miniscule percentage of occurrences of "depends" in
Kconfig files to "depends on", and update kconfig-language.txt to
reflect that.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (76 commits)
[ARM] 4002/1: S3C24XX: leave parent IRQs unmasked
[ARM] 4001/1: S3C24XX: shorten reboot time
[ARM] 3983/2: remove unused argument to __bug()
[ARM] 4000/1: Osiris: add third serial port in
[ARM] 3999/1: RX3715: suspend to RAM support
[ARM] 3998/1: VR1000: LED platform devices
[ARM] 3995/1: iop13xx: add iop13xx support
[ARM] 3968/1: iop13xx: add iop13xx_defconfig
[ARM] Update mach-types
[ARM] Allow gcc to optimise arm_add_memory a little more
[ARM] 3991/1: i.MX/MX1 high resolution time source
[ARM] 3990/1: i.MX/MX1 more precise PLL decode
[ARM] 3986/1: H1940: suspend to RAM support
[ARM] 3985/1: ixp4xx clocksource cleanup
[ARM] 3984/1: ixp4xx/nslu2: Fix disk LED numbering (take 2)
[ARM] 3994/1: ixp23xx: fix handling of pci master aborts
[ARM] 3981/1: sched_clock for PXA2xx
[ARM] 3980/1: extend the ARM Versatile sched_clock implementation from 32 to 63 bit
[ARM] 3979/1: extend the SA11x0 sched_clock implementation from 32 to 63 bit period
[ARM] 3978/1: macro to provide a 63-bit value from a 32-bit hardware counter
...
Merge:
Atmel AT91RM9200 and AT91SAM9260 changes
General ARM developments
Disconfiguous memory cleanups
64-bit/32-bit division and sched_clock extension patches
EP93xx support changes
IOP support changes
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here's a 63-bit implementation of shed_clock() for PXA2xx. The actual
period depends on the value of CLOCK_TICK_RATE and whether or not
reduced scaling factors were provided for it.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dmitry Baryshkov