Since there might be more then one instance it is better to
show the base address when dumping registers to help
with debugging.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation to add colorspace conversion support to VIP,
we need to turn csc.c into its own kernel module.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add RAW8 and RAW16 data type to VPDMA.
To handle RAW format we are re-using the YUV CBY422
vpdma data type so that we use the vpdma to re-order
the incoming bytes, as the VIP parser assumes that the
first byte presented on the bus is the MSB of a 2
bytes value.
RAW8 handles from 1 to 8 bits.
RAW16 handles from 9 to 16 bits.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When scaler is to be used we need to make sure that the input and
output frame size do not exceed the maximum frame sizes that the
scaler h/w can handle otherwise streaming stall as the scaler
cannot proceed.
The scaler buffer is limited to 2047 pixels (i.e. 11 bits) when
attempting anything larger (2048 for example) the scaler stalls.
Realistically in an mem2mem device we can only check for this type
of issue when start_streaming is called. We can't do it during the
try_fmt/s_fmt because we do not have all of the info needed at that
point. So instead when start_streaming is called we need to check
that the input and output frames size do not exceed the scaler's
capability. The only time larger frame size are allowed is when
the input frame szie is the same as the output frame size.
Now in the case where we need to fail, start_streaming must return
all previously queued buffer back otherwise the vb2 framework
will issue kernel WARN messages.
In this case we also give an error message.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since there might be more then one instance it is better to
show the base address when dumping registers to help
with debugging.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation to add scaler support into VIP we need to
turn sc.c into its own kernel module.
Add support for multiple SC memory block as VIP contains
2 scaler instances.
This is done by passing the resource name to sc_create() and
modify the vpe invocation accordingly.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Allow VPE to be able to export DMA buffer.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For deinterlacing operation, VPE hardware uses motion vectors.
MV calculated in the previous iteration are used for next interation.
Therefore driver allocates two motion vectors in ping-pong fashion.
For every transaction, one MV is DMAed in and one is DMAed out.
All the outbound DMAs (DMA to memory) use output parameters, but as
the motion vectors is generated purely out of input fields, it should
use the input parameters for DMA.
Fix the add_out_dtd to use source q_data for creating descriptor.
If the output size is greater than input stride, without this change,
MV DMA may overwrite the buffer causing memory corruption.
This CRITICAL fix ensures that the motion vector DMA descriptor is
created based on the attributes with which the buffer was allocated.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
VPDMA buffer will be used by CPU as well as by the VPDMA.
CPU will write/update the VPDMA descriptors containing data
about the video buffer DMA addresses.
VPDMA will write the "write descriptor" containing the
data about the DMA operation.
When mapping/unmapping the buffer, driver has to take care of
WriteBack and invalidation of the cache so that all the
coherency is maintained from both directions.
Use DMA_BIDIRECTIONAL to maintain coherency between CPU and VPDMA.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
vpdma_create API is supposed to allocated the struct vpdma_data and
return it to the driver. Also, it would call the callback function
when the VPDMA firmware is loaded.
Typically, VPE driver have following function call:
dev->vpdma = vpdma_create(pdev, firmware_load_callback);
And the callback implementation would continue the probe further.
Also, the dev->vpdma is accessed from the callback implementation.
This may lead to race condition between assignment of dev->vpdma
and the callback function being triggered.
This would lead to kernel crash because of NULL pointer access.
Fix this by passing a driver wrapped &vpdma_data instead of allocating
inside vpdma_create.
Change the vpdma_create prototype accordingly and fix return paths.
Also, update the VPE driver to use the updated API and
initialize the dev->vpdma before hand so that the race condition
is avoided.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When stop_streaming is called we need to cleanup the queued
vb2 buffers properly.
This was not previously being done which caused kernel
warning when the application using the resources was killed.
Kernel warnings were also generated on successful completion
of a de-interlacing case as well as upon aborting a
conversion.
Make sure every vb2 buffers is properly handled in all cases.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Current scaler library implementation of sc_set_hs_coeffs and
sc_set_vs_coeffs tries to return immediately if the calculated
coefficient index is already being used.
As the same scaler block is going to be used for all the VPE contexts,
even if the calculated index is same, the parameters have to be
reconfigured for each of the context.
Because of this, when multiple contexts use the same coefficients,
all other contexts would have zero scaling coefficients.
Fix this and also remove the unnecessary hs_index and vs_index fields.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The VPDMA RGB data type definition have been updated
to match with Errata i839.
But some of the ARGB definition appeared to be wrong
in the document also. As they would yield RGBA instead.
They have been corrected based on experimentation.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The YUV data type definition below are taken from
both the TRM and i839 Errata information.
Use the correct data type considering byte
reordering of components.
Added the 2 missing YUV422 variant.
Also since the single use of "C" in the 422 case
to mean "Cr" (i.e. V component). It was decided
to explicitly label them CR to remove any confusion.
Bear in mind that the type label refer to the memory
packed order (LSB - MSB).
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ti_vpe module currently does not get loaded automatically.
Added MODULE_DEVICE_TABLE hint to the driver to assist.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
VPDMA block used in ti-vip and ti-vpe modules have support for
up to 8 hardware descriptor lists. A descriptor list can be
submitted to any of the 8 lists (as long as it's not busy).
When multiple clients want to transfer data in parallel, its easier
to allocate one list per client and let it use it. This way, the
list numbers need not be hard-coded into the driver.
Add support for allocating hwlist and maintain them with a priv data.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
VPE hardware can generate output in RGB565 or in RGB5551 format.
Add these formats in the supported format list for CAPTURE stream.
Also, for RGB5551 format, the alpha component is not processed,
so the alpha value is taken from the default color.
Set the default color to make alpha component full when the dst
format is of RGB color space.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
vpe_irq checks for the possible interrupt sources and prints the
errors for the DEI_ERROR and DS_UV interrupts. But it also post the
next descriptor list irrespective of whichever interrupt has occurred.
Because of this, driver may release the buffers even before DMA is
complete and also schedule next descriptor list.
Fix this by _actually_ handling the IRQ only when ListComplete IRQ
occurs.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For deinterlacing operation, each operation needs 2 fields in the
history. This is achieved by holding three buffers in
ctx->src_vbs[0,1,2] (f,f-1,f-2)
This is achieved by using the ctx->sequence which gets reset via the
s_fmt ioctl.
These buffers are dequeued in stream OFF by calling free_vbs()
But the corresponding references aren't removed anywhere.
When application tries to stream ON and OFF continuously, s_fmt ioctl
won't be called and it won't setup the srcdst parameters.
Setting source/destination parameters in stream ON ioctl would make
sure that the context is re-initialized before it is being used by
the driver.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Current driver configures the line mode of the DEI clients
from the open function directly. Even if the newly created context
is not yet scheduled, it updates some of the VPDMA registers.
This causes a problem in multi instance use case where just opening
the m2m device second time causes the running job to stall. This
happens especially if the source buffers used are NV12.
While all other configuration is being written to context specific
shadow registers, only line mode configuration is happening directly.
As there is no shadow register for line mode configuration, it's better
to separate the config_mode setting and line_mode setting. Call the
new "set_line_modes" functions only when actually loading the mmrs.
This makes sure that no non-running job will write to the registers
directly.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
VPDMA IRQs are registered for multiple lists
When clearing an IRQ for a list interrupt, all the
IRQs for the individual lists are to be cleared separately.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Writing to the "VPDMA list attribute" register is considered as a list
post. This informs the VPDMA firmware to load the list from the address
which should be taken from the "VPDMA list address" register.
As these two register writes are dependent, it is important that the two
writes happen in atomic manner. This ensures multiple slices (which share
same VPDMA) can post lists asynchronously and all of them point to the
correct addresses.
Slightly modified to implementation for the original patch to use
spin_lock instead of mutex as the list post is also called from
interrupt context.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Whenever VPDMA processes a data descriptor of a list, it processes it
and sets up the channel for the DMA transaction. List manager holds the
descriptor in the list until the DMA is complete. If sync_on_channel
descriptor, or another descriptor for the same channel is present in
the FIFO, list manager keeps them until the current channel is free.
When the capture stream is closed suddenly while there are pending
descriptors in the FIFO (streamON failed, application killed), it would
keep the VPDMA in a busy state. Any further list post would fail with
EBUSY.
To avoid this, drivers need to stop the current processing list and
cleanup all the resources VPDMA has taken and also clear the internal FSM
of list manager. The state machine is cleared by issuing channel specific
abort descriptor.
Therefore, the vpdma_list_cleanup accepts an array of channels for which
abort_channel descriptors should be posted. It is driver's responsibility
to post for all the channels or the channels which were used in the last
context.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a helper function to be able to set the maximum
VPDMA transfer size to limit potential buffer overrun.
Added enums for max_width and max_height fields of the
outbound data descriptor.
Changed vpdma_add_out_dtd to accept two more arguments
for max width and height.
Make use of different max width & height sets for different
of capture module (i.e. slices).
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
get_q_data can be called with different values for type
e.g. vpe_try_crop calls it with the buffer type which gets passed
from user space
Framework doesn't check wheather its correct type or not
If user space passes wrong type, kernel should not crash.
Return NULL when the passed type is invalid.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The video source can generate the data in the SEQ_TB buffer format.
In the case of TI SoC, the IVA_HD can generate the interlaced content in
the SEQ_TB buffer format. This is the format where the top and bottom field
data can be contained in a single buffer. For example, for NV12, interlaced
format, the data in Y buffer will be arranged as Y-top followed by
Y-bottom. And likewise for UV plane.
Also, queuing one buffer of SEQ_TB is equivalent to queuing two different
buffers for top and bottom fields. Driver needs to take care of this when
handling source buffer lists.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Current VPE driver does not start the job until all the buffers for
a transaction are queued. When running in multiple context, this might
increase the processing latency.
Alternate solution would be to try to continue the same context as long as
buffers for the transaction are ready; else switch the context. This may
increase number of context switches but it reduces latency significantly.
In this approach, the job_ready always succeeds as long as there are
buffers on the CAPTURE and OUTPUT stream. Processing may start immediately
as the first 2 iterations don't need extra source buffers. Shift all the
source buffers after each iteration and remove the oldest buffer.
Also, with this removes the constraint of pre buffering 3 buffers before
call to STREAMON in case of de-interlacing.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The motion detection block requires 3 fields to create the motion vector
data. This means that using the default method the first progressive
frame is only generated after 3rd field is consumed.
Hence by default for N input field we would generate N - 2 progressive
frames.
In order to generate N progressive frames from N fields we use the
line averaging mode of the de-interlacer for the first 2 fields and then
revert back to the preferred Edge Directed Interpolation method (using
the motion vector).
Thus creating 2 line averaged frames + N - 2 motion based frames for a
total of N frames.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On DRA7 since l3_noc event are being reported it was found that
when the write descriptor was being written it was consistently
causing bus error events.
The write address was improperly programmed.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a helper to set the background color during vpdma transfer.
This is needed when VPDMA is generating 32 bits RGB format
to have the Alpha channel set to an appropriate value.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The VPDMA (Video Port DMA) as found in devices such as DRA7xx is
used for both the Video Processing Engine (VPE) and the Video Input
Port (VIP). Some devices may have multiple VIP instances each with
its own VPDMA engine. Within VIP two slices can use a single VPDMA
engine simultaneously. So support for multi instances and multiple
clients has been added to VPDMA. Needed modification to the existing
helper functions were then reflected to VPE.
Multi-clients registers offset have also been added in preparation.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The VPDMA (Video Port DMA) as found in devices such as DRA7xx is
used for both the Video Processing Engine (VPE) and the Video Input
Port (VIP).
In preparation for this we need to turn vpdma into its own
kernel module.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While checking why we need i386 checking, I noticed that
the serial code referred at the driver was moved to another
place. Update it to make clear from where such code came from.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some CEC adapters will receive messages that they initiated. Add a
check that will ignore such messages.
Most hardware behaves correctly in this respect, but I have seen
adapters that don't, so just filter this out in the framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It can fix known problems with embedded video_device structs.
Signed-off-by: Minghsiu Tsai <minghsiu.tsai@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Trivial fix to spelling mistake "unnsupported" to "unsupported"
in debug message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The maximum 'Max TMDS Rate' in the HDMI VSDB block is 340 MHz, not 600.
Higher rates are advertised in the HDMI Forum VSDB block.
So lower the Max TMDS rate in the HDMI VSDB block that the vivid driver
uses to 300 MHz, which is typical of most HDMI 1.4b devices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix to return error code -ENODEV from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
Remove another reduntdant include, that managed to sneak by commit
97139d4a6f ("treewide: remove redundant #include <linux/kconfig.h>").
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Many lirc drivers have their own receive buffers which are freed on
unplug (e.g. ir_lirc_unregister). This means that ir->buf->wait_poll
will be freed directly after unplug so do not remove yourself from the
wait queue.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If you unplug an lirc device while reading from it, you will get an
use after free as the cdev is freed while still in use.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[ 101.457944] ------------[ cut here ]------------
[ 101.457954] WARNING: CPU: 3 PID: 1819 at kernel/sched/core.c:7708 __might_sleep+0x7e/0x80
[ 101.457960] do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffffc0364bc2>] lirc_dev_fop_read+0x292/0x4e0 [lirc_dev]
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In learning mode, you can get much longer messages which can run out
of lengths. The usb message will slightly larger.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The wideband receiver is a little awkward on the redrat3. Data arrives
on a different endpoint, and the learning command must be reissued
every time data is learned.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If redrat3_delete() is called, ensure ep_in and udev members are set
up so we don't dereference null in the error path. Also ensure that
rc dev device exists before we enable the receiver and that the
led urb exists before we create the led device.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cleanup the error logic, removing checks for things that
should be always initialized when the routines are called,
and remove some bogus messages.
[mchehab@s-opensource.com: fix some merge conflicts]
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Rename the pnp driver in sysfs from /sys/bus/pnp/drivers/Winbond CIR
to /sys/bus/pnp/drivers/winbond-cir
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix to return error code -ENODEV from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
'buf' is malloced in dibusb_rc_query() and should be freed before
leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: ff1c123545 ("[media] dibusb: handle error code on RC query")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A previous patch tried to fix a build error, but introduced another
warning:
drivers/media/platform/mtk-mdp/mtk_mdp_core.c:71:13: error: ‘mtk_mdp_clock_off’ defined but not used [-Werror=unused-function]
drivers/media/platform/mtk-mdp/mtk_mdp_core.c:62:13: error: ‘mtk_mdp_clock_on’ defined but not used [-Werror=unused-function]
This marks all the PM functions as __maybe_unused and removes
the #ifdef around them, as that will always do the right thing.
Fixes: 1b06fcf56a ("[media] media: mtk-mdp: fix build error")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While this patch sounded a good idea, unfortunately, it causes
bad dependencies, as drivers that would otherwise work without
the DVB core will now break:
ERROR: "dvb_tuner_simple_release" [drivers/media/tuners/tea5767.ko] undefined!
ERROR: "dvb_tuner_simple_release" [drivers/media/tuners/tea5761.ko] undefined!
ERROR: "dvb_tuner_simple_release" [drivers/media/tuners/tda827x.ko] undefined!
ERROR: "dvb_tuner_simple_release" [drivers/media/tuners/tda18218.ko] undefined!
ERROR: "dvb_tuner_simple_release" [drivers/media/tuners/qt1010.ko] undefined!
ERROR: "dvb_tuner_simple_release" [drivers/media/tuners/mt2266.ko] undefined!
ERROR: "dvb_tuner_simple_release" [drivers/media/tuners/mt20xx.ko] undefined!
ERROR: "dvb_tuner_simple_release" [drivers/media/tuners/mt2060.ko] undefined!
ERROR: "dvb_tuner_simple_release" [drivers/media/tuners/mc44s803.ko] undefined!
ERROR: "dvb_tuner_simple_release" [drivers/media/tuners/fc0013.ko] undefined!
ERROR: "dvb_tuner_simple_release" [drivers/media/tuners/fc0012.ko] undefined!
ERROR: "dvb_tuner_simple_release" [drivers/media/tuners/fc0011.ko] undefined!
So, we have to revert it.
Note: as the argument for the release ops changed from "int"
to "void", we needed to change it at the revert patch, to
avoid compilation issues like:
drivers/media/tuners/tea5767.c:437:23: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.release = tea5767_release,
^~~~~~~~~~~~~~~
This reverts commit 22a613e898.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On some weird randconfigs, it is possible to select DVB
drivers, without having the DVB_CORE:
CONFIG_DVB_AU8522=m
CONFIG_DVB_AU8522_V4L=m
CONFIG_DVB_TUNER_DIB0090=m
This was never supposed to work, but changeset 22a613e898
("[media] dvb_frontend: merge duplicate dvb_tuner_ops.release implementations")
caused it to be exposed:
drivers/built-in.o: In function `fc0011_attach':
(.text+0x1598fb): undefined reference to `dvb_tuner_simple_release'
drivers/built-in.o:(.rodata+0x55e58): undefined reference to `dvb_tuner_simple_release'
drivers/built-in.o:(.rodata+0x57398): undefined reference to `dvb_tuner_simple_release'
Fixes: 22a613e898 ("[media] dvb_frontend: merge duplicate dvb_tuner_ops.release implementations")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Kernel takes care that interrupts from one source are serialized.
So there's no need to use spinlock_irq_save.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Spinlock nvt_lock is a member of struct nvt_dev and there's no need
to prefix it with nvt_. So remove this prefix.
[mchehab@s-opensource.org: change the prefix also at the open function,
as the patch removing it were not applied (yet?)]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Using a separate spinlock to protect access to substruct tx of struct
nvt_dev doesn't provide any actual benefit. We can use spinlock
nvt_lock to protect all access to struct nvt_dev and get rid of
nvt->tx.lock.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Member pdev of struct nvt_dev is needed only to access &pdev->dev.
We can get rid of this it by using rdev->dev.parent instead
(both point to the same struct device).
Setting rdev->dev.parent can be removed from the probe function
as this is done by devm_rc_allocate_device now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While removing all interfaces in media_device_unregister(), all
media_interface pointers are freed. This is illegal and results in
double kfree() if any media_interface is still linked at this point;
maybe because a userspace process still has a file handle. Once the
process closes the file handle, dvb_media_device_free() gets called,
which frees the dvb_device.intf_devnode again.
This patch removes the unnecessary kfree() call, and documents who's
responsible for really freeing it.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
media_gobj_destroy() may be called twice on one instance - once by
media_device_unregister() and again by dvb_media_device_free(). The
function media_remove_intf_links() establishes and documents the
convention that mdev==NULL means that the object is not registered,
but nobody ever NULLs this variable. So this patch really implements
this behavior, and adds another mdev==NULL check to
media_gobj_destroy() to protect against double removal.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Ensure that STB0899_POSTPROC_GPIO_POWER is set synchronously.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Prepare for making "release" asynchronous (via kref). Some operations
may need to be run synchronously in dvb_frontend_detach(), and that's
why we need a "detach" callback.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This code duplication is confusing and error prone. Let's merge them
by moving the release/dvb_detach call into one function with one
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It is not clear what this return value means. All implemenations
return 0, and the one caller ignores the value. Let's remove this
useless return value completely.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most release callback functions are identical: free the "tuner_priv"
and clear it. Let's eliminate some bloat by providing this simple
implementation in the dvb_frontend library.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit da677fe143 ("[media] dvb-core/en50221: use kref to manage
struct dvb_ca_private") moved the dvb_unregister_device() call to the
kref callback, but that left lots of stale device state visible to
userspace (e.g. in sysfs). By using dvb_remove_device() and
dvb_free_device() instead of dvb_unregister_device(), we can avoid
that.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dvb_unregister_device() has a major problem: it combines unregistering
with memory disposal. Sometimes, it is necessary to unregister a
device, but no memory can be freed yet, because a process still has a
(stale) file handle. Therefore, we need to split
dvb_unregister_device(). This will allow sanitizing a few callers.
With my new design, dvb_unregister_device() appears misnamed, but to
reduce patch noise, I'm not renaming it just yet.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These are immutable. Making them "const" allows the compiler to move
them to the "rodata" section.
Note that cxd2841er_t_c_ops cannot be made "const", because
cxd2841er_attach() modifies it. Ouch!
[mchehab@s-opensource.com: fix merge conflicts]
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
rc_unregister_device() will first call ir_free_table(), and later
device_del(); however, the latter causes a call to rc_dev_uevent(),
which prints rc_map.name, which at this point has already bee freed.
This fixes a use-after-free bug found with KASAN.
As reported by Shuah:
"I am seeing the following when I do rmmod on au0828
BUG: KASAN: use-after-free in string+0x170/0x1f0 at addr ffff8801bd513000
Read of size 1 by task rmmod/1831
CPU: 1 PID: 1831 Comm: rmmod Tainted: G W 4.9.0-rc5 #5
Hardware name: Hewlett-Packard HP ProBook 6475b/180F, BIOS 68TTU Ver. F.04 08/03/2012
ffff8801aea2f680 ffffffff81b37ad3 ffff8801fa403b80 ffff8801bd513000
ffff8801aea2f6a8 ffffffff8156c301 ffff8801aea2f738 ffff8801bd513000
ffff8801fa403b80 ffff8801aea2f728 ffffffff8156c59a ffff8801aea2f770
Call Trace:
dump_stack+0x67/0x94
[<ffffffff8156c301>] kasan_object_err+0x21/0x70
[<ffffffff8156c59a>] kasan_report_error+0x1fa/0x4d0
[<ffffffffa116f05f>] ? au0828_exit+0x10/0x21 [au0828]
[<ffffffff8156c8b3>] __asan_report_load1_noabort+0x43/0x50
[<ffffffff81b58b20>] ? string+0x170/0x1f0
[<ffffffff81b58b20>] string+0x170/0x1f0
[<ffffffff81b621c4>] vsnprintf+0x374/0x1c50
[<ffffffff81b61e50>] ? pointer+0xa80/0xa80
[<ffffffff8156b676>] ? save_stack+0x46/0xd0
[<ffffffff81566faa>] ? __kmalloc+0x14a/0x2a0
[<ffffffff81b3d70a>] ? kobject_get_path+0x9a/0x200
[<ffffffff81b408c2>] ? kobject_uevent_env+0x282/0xca0
[<ffffffff81b412eb>] ? kobject_uevent+0xb/0x10
[<ffffffff81f10104>] ? device_del+0x434/0x6d0
[<ffffffffa0fea717>] ? rc_unregister_device+0x177/0x240 [rc_core]
[<ffffffffa116eeb0>] ? au0828_rc_unregister+0x60/0xb0 [au0828]
The problem is fixed with this patch on Linux 4.9-rc4"
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Tested-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
devm_pinctrl_get() can fail so we should check for that.
Fixes: 0a6824bc10 ('[media] v4l2: blackfin: select proper pinctrl state in ppi_set_params if CONFIG_PINCTRL is enabled')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is no need to check for CONFIG_COMPAT and consequently
assign the compat_ioctl.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When saa7134 module driving a Medion 7134 card is reloaded reads of this
card EEPROM (required for automatic detection of tuner model) will be
corrupted due to I2C gate in DVB-T demod being left closed.
This sometimes also happens on first saa7134 module load after a warm
reboot.
Fix this by opening this I2C gate before doing EEPROM read during i2c
initialization.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that CLK_PROC_STFE is defined as a critical clock in
DT, we can remove the commented clk_disable_unprepare from
the c8sectpfe driver. This means we now have balanced
clk*enable/disable calls in the driver, but on STiH407
family the clock in reality will never actually be disabled.
This is due to a HW bug where once the IP has been configured
and the SLIM core is running, disabling the clock causes a
unrecoverable bus lockup.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
-----BEGIN PGP SIGNATURE-----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=5WN9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Return directly after a call of the function "rc_allocate_device" failed
at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The local variable "ret" will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The local variable "rc" will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* Return directly after a call of the function "kcalloc" failed
at the beginning.
* Reorder two calls for the function "kfree" at the end.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the specification of a data type by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script "checkpatch.pl" pointed information out like the following.
WARNING: Possible unnecessary 'out of memory' message
Thus remove such a logging statement in five functions.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* Multiplications for the size determination of memory allocations
indicated that array data structures should be processed.
Thus use the corresponding function "kcalloc".
This issue was detected by using the Coccinelle software.
* Replace the specification of data types by pointer dereferences
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Unfortunately, the callers of tveeprom don't do the right
thing to initialize the device. So, it produces log messages
like:
[ 267.533010] (null): Hauppauge model 42012, rev C186, serial# 2819348
[ 267.533012] (null): tuner model is Philips FQ1236 MK3 (idx 86, type 43)
[ 267.533013] (null): TV standards NTSC(M) (eeprom 0x08)
[ 267.533014] (null): audio processor is MSP3445 (idx 12)
[ 267.533015] (null): has radio
So, replace it to pr_foo(), as it should work fine.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of calling printk() directly, use pr_foo() macro.
That should make the rc_core messages be formatted with the
right prefix.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Unfortunately, KERN_CONT doesn't work with dev_foo(),
producing weird messages like:
tvp5150 6-005c: tvp5150: read 0xf6 = 0xff
ff
So, we need to get rid of it.
As we're always printing read/write in hexa when dumping
multiple register values, also remove the "0x" from the
read/write debug messages too.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When returning results via v4l2_subdev_core_ops.log_status,
use dev_foo() call, instead of just calling printk()
directly, without even specifying the log message level.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of using pr_foo(), use dev_foo(), with provides a
better output. As this device is a multi-interface one,
we'll set the device name to show the chipset and the driver
used.
While here, get rid of printk continuation messages.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of using the v4l_foo() macros, just use the
kernel-wide dev_foo() macros, as there's no good reason
to use something else.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drivers using dev_foo() macro should not use KERN_CONT, as, internally,
those macros work as if all strings were terminated by a \n. So, doing:
dev_info(&client->dev, "%s ", client->name);
printk(KERN_CONT "supports radio, mode is autodetect and autoselect");
Would produce the following output:
msp3400 6-0044: msp3400
supports radio, mode is autodetect and autoselect
As there's no good reason to use KERN_CONT, let's rewrite the code
to avoid that, allowing this driver to be converted to dev_foo().
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Tuner core uses its own printk internal macros, instead of the
standard debug ones, for no good reason.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dvb-usb system has its own macro to print hexa dumps
(debug_dump). Such macro doesn't support messages with
KERN_CONT after commit 563873318d ("Merge branch 'printk-cleanups'").
So, let's get rid of a printk() that would be assuming that
this would work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dprintk() macro relies on continuation lines. This is not
a good practice and will break after commit 563873318d
("Merge branch 'printk-cleanups'").
So, instead of directly calling printk(), use pr_foo() macros,
adding a \n leading char on each macro call.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dprintk() macro relies on continuation lines. This is not
a good practice and will break after commit 563873318d
("Merge branch 'printk-cleanups'").
So, instead of directly calling printk(), use pr_foo() macros,
adding a\n leading char on each macro call.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dprintk() macro relies on continuation lines. This is not
a good practice and will break after commit 563873318d
("Merge branch 'printk-cleanups'").
So, instead of directly calling printk(), use pr_foo() macros,
adding a\n leading char on each macro call.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dprintk() macro relies on continuation lines. This is not
a good practice and will break after commit 563873318d
("Merge branch 'printk-cleanups'").
So, instead of directly calling printk(), use pr_foo() macros,
adding a \n leading char on each macro call.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dprintk() macro relies on continuation lines. This is not
a good practice and will break after commit 563873318d
("Merge branch 'printk-cleanups'").
So, instead of directly calling printk(), use pr_foo() macros,
adding a \n leading char on each macro call.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dprintk() macro relies on continuation lines. This is not
a good practice and will break after commit 563873318d
("Merge branch 'printk-cleanups'").
So, instead of directly calling printk(), use pr_foo() macros,
adding a \n leading char on each macro call.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dprintk() macro relies on continuation lines. This is not
a good practice and will break after commit 563873318d
("Merge branch 'printk-cleanups'").
So, instead of directly calling printk(), use pr_foo() macros,
adding a \n leading char on each macro call.
The frontend settings also rely on continuation lines. Change
it to avoid the need of adding pr_cont() calls.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dprintk() macro relies on continuation lines. This is not
a good practice and will break after commit 563873318d
("Merge branch 'printk-cleanups").
So, instead of directly calling printk(), use pr_foo() macros,
adding a \n leading char on each macro call.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dprintk() macro relies on continuation lines. This is not
a good practice and will break after commit 563873318d
("Merge branch 'printk-cleanups").
So, instead of directly calling printk(), use pr_foo() macros,
adding a \n leading char on each macro call.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Continuation lines without KERN_CONT won't work anymore.
However, the way dprintk() was defined leads to the usage
of continuation lines, with should be avoided when possible.
So, redefine those macros.
While hre, remove some dead code at av7110.c with also
relies on continuation lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some continuation messages are not using KERNEL_CONT.
Since commit 563873318d ("Merge branch 'printk-cleanups"),
this won't work as expected anymore. So, let's add KERN_CONT
to those lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some continuation messages are not using KERNEL_CONT.
Since commit 563873318d ("Merge branch 'printk-cleanups"),
this won't work as expected anymore. So, let's add KERN_CONT
to those lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some continuation messages are not using KERNEL_CONT.
Since commit 563873318d ("Merge branch 'printk-cleanups"),
this won't work as expected anymore. So, let's add KERN_CONT
to those lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some continuation messages are not using KERN_CONT.
Since commit 563873318d ("Merge branch 'printk-cleanups"),
this won't work as expected anymore. So, let's add KERN_CONT
to those lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some continuation messages are not using KERN_CONT.
Since commit 563873318d ("Merge branch 'printk-cleanups"),
this won't work as expected anymore. So, let's add KERN_CONT
to those lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver is old, and have lots of checkpatch violations.
As we're touching a lot on this driver due to the printk
conversions, let's run checkpatch --fix on it, in order to
solve some of those issues.
Also, do a few manual adjustments:
- remove the FSF address and use the usual coding style
for the initial comments;
- use WARN_ON() instead of BUG_ON();
- remove an unused typedef;
- break a few long lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of calling printk() directly, use pr_foo()
macros, as suggested at the Kernel's coding style.
Please notice that a conversion to dev_foo() is not trivial,
as several parts on this driver uses pr_cont().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some continuation messages are not using KERN_CONT.
Since commit 563873318d ("Merge branch 'printk-cleanups'"),
this won't work as expected anymore. So, let's add KERN_CONT
to those lines.
While here, add missing log level annotations.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of calling printk() directly, use pr_foo()
macros, as suggested at the Kernel's coding style.
Please notice that a conversion to dev_foo() is not trivial,
as several parts on this driver uses pr_cont().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This file was converted to a separate module at commit 7a0786c19d
("gp8psk: Fix DVB frontend attach"), because the DVB attach routines
require it to work. However, I forgot to copy the MODULE_foo() macros
from the original module, causing this warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/media/dvb-frontends/gp8psk-fe.o
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 7a0786c19d ("gp8psk: Fix DVB frontend attach")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some continuation messages are not using KERN_CONT.
Since commit 563873318d ("Merge branch 'printk-cleanups'"),
this won't work as expected anymore. So, let's add KERN_CONT
to those lines.
While here, add missing log level annotations.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace printk() macros by their pr_foo() counterparts, using
pr_cont() for continuation lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver uses a weird, non-standard macro to print errors.
It allows hiding all messages, including error ones, with doesn't
seem a good idea.
Instead, replace it to pr_foo(), and, for error messages,
use pr_err().
The remaining messages were previouly classified as notice,
info or debug, but they all looked like debug messages.
So, add a dprintk() macro using the "verbose" modprobe
argument to select what will be displayed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver has printk continuation lines for debugging purposes.
Since commit 563873318d ("Merge branch 'printk-cleanups'")',
this won't work as expected anymore.
So, use %*ph and get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver has printk continuation lines for debugging purposes.
Since commit 563873318d ("Merge branch 'printk-cleanups'")',
this won't work as expected anymore.
So, use %*ph and get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Clock control indirectly requires access to MFC device, so call it only
if we are sure that the device exists in s5p_mfc_release function.
s5p_mfc_remove() calls s5p_mfc_final_pm(), which releases all PM related
resources, including clocks, so any call to clocks related functions
is not valid after s5p_mfc_final_pm().
Fixes: d695c12 ("[media] media: s5p-mfc fix invalid memory access from
s5p_mfc_release()")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Newer MFC hardware have internal clock gating feature, so additional
software-triggered clock gating sometimes causes misbehavior of the MFC
firmware and results in freeze or crash. This patch changes the driver
to use software-triggered clock gating only when working with v5 MFC
hardware, where it has been proven to work properly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, when incomplete frame is received in the middle of
decoding, driver treats it as an error, so src/dst queue and
clock are cleaned. Although it is obviously error case, it is
needed to maintain video decoding in case of necessity. This
patch supports skip incomplete frame to next.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Driver complains about too small scratch buffer size. After adjusting
it according to vendor code, decoding works.
[mszyprow: moved the change to the header file]
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds support for Exynos5433 specific version of the GScaler
module. The main difference between Exynos 5433 and earlier is addition
of new clocks that have to be controlled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver can be also used on Exynos5433, which is ARM64-based
platform, which selects only ARCH_EXYNOS symbol.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
System PM callbacks only ensure that device is runtime suspended/resumed,
so remove them and use generic pm_runtime_force_suspend/resume helper.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It's not needed to keep a local flag about the current system PM state.
Let's just remove that code and the corresponding debug print.
[mszyprow: rebased onto v4.9-rc4]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
To potentially save more power in runtime PM suspend state, let's
also prepare/unprepare the clock from the runtime PM callbacks.
[mszyprow: rebased onto v4.9-rc4]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
To make sure the clock is fully gated in ->remove(), we first need to
to bring the device into full power by invoking pm_runtime_get_sync().
Then, let's both unprepare and disable the clock.
[mszyprow: rebased onto v4.9-rc4]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are no need to set up the PM callbacks (runtime and system) unless
they are being used. It also causes compiler warnings about unused
functions.
Silence the warnings by making them available for CONFIG_PM (runtime
callbacks) and CONFIG_PM_SLEEP (system sleep callbacks).
[mszyprow: squashed two patches into one to avoid potential build
break, changed patch subject and updated commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver depended on CONFIG_PM to be functional. Let's remove that
dependency, by enable the runtime PM resourses during ->probe() and
update the device's runtime PM status to reflect this.
[mszyprow: rebased onto v4.9-rc4]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of having separate functions that fetches, prepares and
unprepares the clock, let's encapsulate this code into ->probe().
This makes error handling easier and decreases the lines of code.
[mszyprow: rebased onto v4.9-rc4]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Include buffer size in s5p_mfc_alloc_priv_buf() the error message
when it fails to allocate the buffer.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Media drivers that use the videobuf2 framework have to give back to vb2
all the buffers that received from vb2 using its .buf_queue callback.
But the exynos-gsc driver isn't doing a proper cleanup so vb2 complains
that the number of buffers enqueued and received are not balanced:
WARNING: CPU: 2 PID: 660 at drivers/media/v4l2-core/videobuf2-core.c:1654 __vb2_queue_cancel+0xec/0x150 [videobuf2_core]
Modules linked in: mwifiex_sdio mwifiex uvcvideo exynos_gsc videobuf2_vmalloc s5p_mfc s5p_jpeg
CPU: 2 PID: 660 Comm: lt-gst-validate Not tainted 4.8.0
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c010e24c>] (unwind_backtrace) from [<c010af30>] (show_stack+0x10/0x14)
[<c010af30>] (show_stack) from [<c03291a4>] (dump_stack+0x88/0x9c)
[<c03291a4>] (dump_stack) from [<c011a858>] (__warn+0xe8/0x100)
[<c011a858>] (__warn) from [<c011a920>] (warn_slowpath_null+0x20/0x28)
[<c011a920>] (warn_slowpath_null) from [<bf0b6ed0>] (__vb2_queue_cancel+0xec/0x150 [videobuf2_core])
[<bf0b6ed0>] (__vb2_queue_cancel [videobuf2_core]) from [<bf0b7464>] (vb2_core_streamoff+0x34/0x9c [videobuf2_core])
[<bf0b7464>] (vb2_core_streamoff [videobuf2_core]) from [<bf11b9e8>] (v4l2_m2m_streamoff+0x2c/0xe4 [v4l2_mem2mem])
[<bf11b9e8>] (v4l2_m2m_streamoff [v4l2_mem2mem]) from [<bf01b84c>] (__video_do_ioctl+0x298/0x30c [videodev])
[<bf01b84c>] (__video_do_ioctl [videodev]) from [<bf01b234>] (video_usercopy+0x174/0x4e8 [videodev])
[<bf01b234>] (video_usercopy [videodev]) from [<bf0165c8>] (v4l2_ioctl+0xc4/0xd8 [videodev])
[<bf0165c8>] (v4l2_ioctl [videodev]) from [<c01f291c>] (do_vfs_ioctl+0x9c/0x8f4)
[<c01f291c>] (do_vfs_ioctl) from [<c01f31a8>] (SyS_ioctl+0x34/0x5c)
[<c01f31a8>] (SyS_ioctl) from [<c01078c0>] (ret_fast_syscall+0x0/0x3c)
Fix this by passing back to vb2 all the received buffers that were not
processed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The struct v4l2_device instance for the G-Scaler is not dyanmically
allocated but a member of the struct gsc_dev. In fact, the assigned
.release callback is video_device_release_empty().
But gsc_register_m2m_device() attempts to release the v4l2_device by
calling video_device_release() in its error path. This is wrong since
the v4l2_device wasn't allocated directly and will be freed once its
parent struct gsc_dev is freed.
While being there, rename the remaining goto label in the error path
to something that better explains the error path cleanup.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver don't take into account the differences between packed, semi
planar and multi planar formats when calculating the pixel format bytes
per lines and image size values. This makes GStreamer to fail when the
following formats are used NV12, NV21, NV16, NV61, YV12, I420 and Y42B:
"gst_video_frame_map_id: failed to map video frame plane 1"
Nicolas suggested to use the logic found in the Exynos FIMC v4l2 driver
since does this correctly. So this patch changes the bytes per line and
image size calculation according to what's done in this media driver.
After this patch most supported formats work correctly. There are still
issues with the NV21 and NV61 formats, but that seems to be a separate
problem since NV12 and NV16 work and these formats use the same values.
So this can be fixed as a follow-up and shouldn't be a blocker for this
change that improves the driver's support.
Suggested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver exposes 32-bit A/XRGB 8-8-8-8 as supported format but testing
shows that using this format produces frames with wrong colors. The test
was done with the following GStreamer pipeline:
$ gst-launch-1.0 videotestsrc num-buffers=20 ! video/x-raw,format=UYVY \
! v4l2video3convert ! video/x-raw,format=xRGB ! videoconvert ! kmssink
The manual seems to state that the Pixel Format are in Little Endianness
so instead use the 32-bit BGRA/X 8-8-8-8 pixel format. This format works
correctly when using the following pipeline:
$ gst-launch-1.0 videotestsrc num-buffers=20 ! video/x-raw,format=UYVY \
! v4l2video3convert ! video/x-raw,format=BGRx ! kmssink
This change is similar to commit 7f2816e51e ("[media] s5p-fimc: Changed
RGB32 to BGR32") that fixed the same issue on a different Samsung driver.
Suggested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
User-space applications can use the VIDIOC_REQBUFS ioctl to determine if a
memory mapped, user pointer or DMABUF based I/O is supported by a driver.
For example, GStreamer attempts to determine the I/O methods supported by
the driver by doing many VIDIOC_REQBUFS ioctl calls with different memory
types and count 0. And then the real VIDIOC_REQBUFS call with count == n
is be made to allocate the buffers. But for count 0, the driver not only
frees the buffers but also clears the format set before with VIDIOC_S_FMT.
This is a problem since STREAMON fails if a format isn't set but GStreamer
first sets a format and then tries to determine the supported I/O methods,
so the format will be cleared on REQBUFS(0), before the call to STREAMON.
To avoid this issue, only free the buffers on VIDIOC_REQBUFS(0) but don't
clear the format. Since is completely valid to set the format and then do
different calls to REQBUFS before a call to STREAMON.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver try_fmt handler prints a message each time that the image
size has been changed due the maximum and minimum width and height.
Since user-space can try different format and sizes, this logs a lot
of unnecessary messages. Change the message log level to debug and
while being there, also add a new line to the message.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
s5p_mfc_alloc_priv_buf() prints two message to report invalid memory
configuration error. Collapse them into a single message.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For tiled format, we need to allocated a multiple of the row size. A
good example is for 1280x720, wich get adjusted to 1280x736. In tiles,
this mean Y plane is 20x23 and UV plane 20x12. Because of the rounding,
the previous code would only have enough space to fit half of the last
row.
[mchehab@s-opensource.com: fix coding style]
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The FDP1 driver performs advanced de-interlacing on a memory 2 memory
based video stream, and supports conversion from YCbCr/YUV
to RGB pixel formats
Signed-off-by: Kieran Bingham <kieran+renesas@bingham.xyz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The menu control selects the operation mode of a video deinterlacer. The
menu entries are driver specific.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran@bingham.xyz>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When requesting the DMA channel it was mandatory that we do not have DMA
resource nor valid DMA channel via DT. In this case the
dma_request_slave_channel_compat() would fall back and request any channel
with SW trigger.
The same can be achieved with the dma_request_chan_by_mask() without the
misleading use of the DMAengine API - implying that the omap3isp does
need to have DMA resource or valid dma binding in DT.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When parsing the graph the driver loops over all endpoints using
of_graph_get_next_endpoint(). The function handles reference counting of
the passed and returned nodes, so the returned node's reference count
must not be decreased manually in the normal path.
Move the offending of_node_put() call to the error path that requires
manual reference count handling.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Rift CV1 Sensor has bInterfaceClass set to vendor specific, so we
need an entry in uvc_ids to probe it. Just as the Rift DK2 IR tracker,
it misreports the pixel format as YUYV instead of Y8.
The sensor is configured with a low exposure time and high black level
by default, so that only bright IR sources can be seen.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure the TX counters are zeroed in the cec_msg struct.
Non-zero TX counters make no sense when a message is received,
and applications should not see non-zero values here.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that the CEC framework has been moved out of staging and into the
mainline kernel we can do the same for the pulse8-cec driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
An inner for-loop reused the outer loop variable. This was
only noticeable with CEC adapters supporting more than one
logical address.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC_MSG_FL_REPLY_TO_FOLLOWERS message flag only makes sense for transmitted
messages where you want to wait for the reply.
Clear the flag in all other cases.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The last open issues have been addressed, so it is time to move
this out of staging and into the mainline and to move the public
cec headers to include/uapi/linux.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The vmr_stat variable was filled with the contents of the control register,
not the status register. Classic copy-and-paste error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
vb2_qbuf will check the buffer index. If a driver overrides
vidioc_qbuf and use the buffer index, the driver needs to check
the index.
Signed-off-by: Wu-Cheng Li <wuchengli@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use a direct assignment for an array element which can be set over the
pointer variable "inp" instead of calling the function "memcpy" here.
Suggested-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* A function was called over the pointer "setup_if_config" in the data
structure "venc_platform_data". But the return value was not used so far.
Thus assign it to the local variable "ret" which will be checked with
the next statement.
Fixes: 9a7f95ad1c ("[media] davinci vpbe: add dm365 VPBE display driver changes")
* Pass a value to this function call without storing it in an intermediate
variable before.
* Delete the local variable "if_params" which became unnecessary with
this refactoring.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Obtain the correct timings based on the VIC code from the AVI InfoFrame.
It does a sanity check to see if at least the measured width and height
are in line with what the VIC code reports. If not, then use the timings
instead of the VIC code (as per the CEA-861 spec).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that the timings contain picture aspect ratio information,
we can support cropcap to return the pixel aspect ratio.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a helper to find timings based on the CEA-861 VIC code. Also,
add a helper that returns the pixel aspect ratio based on the
v4l2_dv_timings struct.
[mchehab@s-opensource.com: fix coding style]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a reworking of a patch originally submitted by Ryley Angus,
modified by Hans Verkuil and then seemingly forgotten before changes
suggested by Keith Pyle here:
http://www.mail-archive.com/linux-media@vger.kernel.org/msg75163.html
were made and tested.
I have implemented the suggested changes and have been testing for the
last 2 months. I am no longer experiencing lockups while recording
(with blue light on, requiring power cycling) which had been a long
standing problem with the HD-PVR. I have not noticed any other problems
since applying the patch.
Signed-off-by: Jonathan Sims <jonathan.625266@earthlink.net>
Reported-by: Ryley Angus <ryleyjangus@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The second check for an error on hva->lmi_err_reg appears
to be a copy-and-paste error, it should be hva->emi_err_reg
instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jean-Christophe Trotin <jean-christophe.trotin@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/platform/mtk-mdp/mtk_mdp_core.c:284:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Minghsiu Tsai <minghsiu.tsai@mediatek.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fixes a lockup at device probing which happens on some solo6010
hardware samples. This is a regression introduced by commit e1ceb25a15
("[media] SOLO6x10: remove unneeded register locking and barriers")
The observed lockup happens in solo_set_motion_threshold() called from
solo_motion_config().
This extra "flushing" is not fundamentally needed for every write, but
apparently the code in driver assumes such behaviour at last in some
places.
Actual fix was proposed by Hans Verkuil.
Fixes: e1ceb25a15 ("[media] SOLO6x10: remove unneeded register locking and barriers")
Cc: stable@vger.kernel.org # 4.3 and up
Signed-off-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/media/rc/meson-ir.ko | grep alias
$
After this patch:
$ modinfo drivers/media/rc/meson-ir.ko | grep alias
alias: of:N*T*Camlogic,meson-gxbb-irC*
alias: of:N*T*Camlogic,meson-gxbb-ir
alias: of:N*T*Camlogic,meson8b-irC*
alias: of:N*T*Camlogic,meson8b-ir
alias: of:N*T*Camlogic,meson6-irC*
alias: of:N*T*Camlogic,meson6-ir
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/media/platform/rcar-fcp.ko | grep alias
alias: rcar-fcp
After this patch:
$ modinfo drivers/media/platform/rcar-fcp.ko | grep alias
alias: rcar-fcp
alias: of:N*T*Crenesas,fcpvC*
alias: of:N*T*Crenesas,fcpv
alias: of:N*T*Crenesas,fcpfC*
alias: of:N*T*Crenesas,fcpf
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/media/platform/vsp1/vsp1.ko | grep alias
alias: vsp1
After this patch:
$ modinfo drivers/media/platform/vsp1/vsp1.ko | grep alias
alias: vsp1
alias: of:N*T*Crenesas,vsp2C*
alias: of:N*T*Crenesas,vsp2
alias: of:N*T*Crenesas,vsp1C*
alias: of:N*T*Crenesas,vsp1
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As reported by smatch:
drivers/media/usb/usbtv/usbtv-video.c:716 usbtv_s_ctrl() error: doing dma on the stack (data)
drivers/media/usb/usbtv/usbtv-video.c:758 usbtv_s_ctrl() error: doing dma on the stack (data)
We should not do it, as it won't work on Kernels 4.9 and upper.
So, alloc a buffer for it.
Fixes: c53a846c48 ("[media] usbtv: add video controls")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The devm_ioremap_resource() returns error pointers, never NULL. The
platform_get_resource() returns NULL on error, never error pointers.
The error code needs to be set, as well. The current code returns
PTR_ERR(NULL) which is success.
Fixes: 57b2c0628b ("[media] st-hva: multi-format video encoder V4L2 driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jean-Christophe Trotin <jean-christophe.trotin@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The local variable "addr" will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The local variable "channel_id" will be reassigned with the following
statement at the beginning. Thus omit the explicit initialisation.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script "checkpatch.pl" pointed information out like the following.
Comparison to NULL could be written...
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kcalloc".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The local variable "channel_id" will be set to an appropriate value
a bit later. Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The local variable "ret" will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script "checkpatch.pl" pointed information out like the following.
Comparison to NULL could be written ...
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kcalloc".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script "checkpatch.pl" pointed information out like the following.
WARNING: void function return statements are not generally useful
Thus remove such a statement here.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Do not use curly brackets at one source code place
where a single statement should be sufficient.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move assignments for two local variables into an else branch so that
their setting will only be performed after corresponding data processing
succeeded by this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The local variable "ret" will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert comparisons with the preprocessor symbol "NULL" to condition checks
without it.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* Return an error code as a constant after a failed call of
the function "vpfe_initialize".
* The local variable "ret" will be set then to an appropriate value
a bit later. Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script "checkpatch.pl" pointed information out like the following.
WARNING: Possible unnecessary 'out of memory' message
Thus remove such a logging statement in two functions.
Link: http://events.linuxfoundation.org/sites/events/files/slides/LCJ16-Refactor_Strings-WSang_0.pdf
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The local variable "ret" will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adjust jump labels according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* Move the definition for the variable "ret" into an if branch
so that an extra initialisation can be avoided at the beginning
by this refactoring.
* Return a success code as a constant at the end.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* Return a success code without storing it in an intermediate variable.
* Delete the local variable "ret" which became unnecessary with
this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* Return an error code without storing it in an intermediate variable.
* Delete the local variable "ret" which became unnecessary with
this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script "checkpatch.pl" pointed information out like the following.
Comparison to NULL could be written ...
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script "checkpatch.pl" pointed information out like the following.
WARNING: Possible unnecessary 'out of memory' message
Thus remove such a logging statement in two functions.
Link: http://events.linuxfoundation.org/sites/events/files/slides/LCJ16-Refactor_Strings-WSang_0.pdf
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script "checkpatch.pl" pointed information out like the following.
WARNING: Possible unnecessary 'out of memory' message
Thus remove such a statement here.
Link: http://events.linuxfoundation.org/sites/events/files/slides/LCJ16-Refactor_Strings-WSang_0.pdf
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus reuse the corresponding function "kcalloc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use space characters at some source code places according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adjust a jump label according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This file was converted to a separate module at commit 7a0786c19d
("gp8psk: Fix DVB frontend attach"), because the DVB attach routines
require it to work. However, I forgot to copy the MODULE_foo() macros
from the original module, causing this warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/media/dvb-frontends/gp8psk-fe.o
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 7a0786c19d ("gp8psk: Fix DVB frontend attach")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DVB binding schema at the DVB core assumes that the frontend is a
separate driver. Faling to do that causes OOPS when the module is
removed, as it tries to do a symbol_put_addr on an internal symbol,
causing craches like:
WARNING: CPU: 1 PID: 28102 at kernel/module.c:1108 module_put+0x57/0x70
Modules linked in: dvb_usb_gp8psk(-) dvb_usb dvb_core nvidia_drm(PO) nvidia_modeset(PO) snd_hda_codec_hdmi snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm snd_timer snd soundcore nvidia(PO) [last unloaded: rc_core]
CPU: 1 PID: 28102 Comm: rmmod Tainted: P WC O 4.8.4-build.1 #1
Hardware name: MSI MS-7309/MS-7309, BIOS V1.12 02/23/2009
Call Trace:
dump_stack+0x44/0x64
__warn+0xfa/0x120
module_put+0x57/0x70
module_put+0x57/0x70
warn_slowpath_null+0x23/0x30
module_put+0x57/0x70
gp8psk_fe_set_frontend+0x460/0x460 [dvb_usb_gp8psk]
symbol_put_addr+0x27/0x50
dvb_usb_adapter_frontend_exit+0x3a/0x70 [dvb_usb]
From Derek's tests:
"Attach bug is fixed, tuning works, module unloads without
crashing. Everything seems ok!"
Reported-by: Derek <user.vdr@gmail.com>
Tested-by: Derek <user.vdr@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit bc29131ecb10 ("[media] gp8psk: don't do DMA on stack") fixed the
usage of DMA on stack, but the memcpy was wrong for gp8psk_usb_in_op().
Fix it.
From Derek's email:
"Fix confirmed using 2 different Skywalker models with
HD mpeg4, SD mpeg2."
Suggested-by: Johannes Stezenbach <js@linuxtv.org>
Fixes: bc29131ecb10 ("[media] gp8psk: don't do DMA on stack")
Tested-by: Derek <user.vdr@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A recent rework accidentally left a debugging printk untouched while
changing the meaning of the variables, leading to an uninitialized
variable being printed:
drivers/media/i2c/ir-kbd-i2c.c: In function 'get_key_haup_common':
drivers/media/i2c/ir-kbd-i2c.c:62:2: error: 'toggle' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This prints the correct one instead, as we did before the patch.
Fixes: 00bb820755 ("[media] rc: Hauppauge z8f0811 can decode RC6")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When receiving a nec repeat, ensure the correct scancode is repeated
rather than a random value from the stack. This removes the need for
the bogus uninitialized_var() and also fixes the warnings:
drivers/media/usb/dvb-usb/dib0700_core.c: In function ‘dib0700_rc_urb_completion’:
drivers/media/usb/dvb-usb/dib0700_core.c:679: warning: ‘protocol’ may be used uninitialized in this function
[sean addon: So after writing the patch and submitting it, I've bought the
hardware on ebay. Without this patch you get random scancodes
on nec repeats, which the patch indeed fixes.]
Signed-off-by: Sean Young <sean@mess.org>
Tested-by: Sean Young <sean@mess.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=MRLH
-----END PGP SIGNATURE-----
Merge tag 'media/v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A series of fixup patches meant to fix the usage of DMA on stack, plus
one warning fixup"
* tag 'media/v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (32 commits)
[media] radio-bcm2048: don't ignore errors
[media] pctv452e: fix semicolon.cocci warnings
[media] flexcop-usb: don't use stack for DMA
[media] stk-webcam: don't use stack for DMA
[media] s2255drv: don't use stack for DMA
[media] cpia2_usb: don't use stack for DMA
[media] digitv: handle error code on RC query
[media] dw2102: return error if su3000_power_ctrl() fails
[media] nova-t-usb2: handle error code on RC query
[media] technisat-usb2: use DMA buffers for I2C transfers
[media] pctv452e: don't call BUG_ON() on non-fatal error
[media] pctv452e: don't do DMA on stack
[media] nova-t-usb2: don't do DMA on stack
[media] gp8psk: don't go past the buffer size
[media] gp8psk: don't do DMA on stack
[media] dtv5100: don't do DMA on stack
[media] dtt200u: handle USB control message errors
[media] dtt200u: don't do DMA on stack
[media] dtt200u-fe: handle errors on USB control messages
[media] dtt200u-fe: don't do DMA on stack
...
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: <linux-media@vger.kernel.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 079933dbcb ("[media] v4l: flash led class: Fix of_node release
in probe() error path") removed the need of an ancillary var at
the release function, as reported by smatch:
drivers/media/v4l2-core/v4l2-flash-led-class.c: In function 'v4l2_flash_release':
drivers/media/v4l2-core/v4l2-flash-led-class.c:678:23: warning: variable 'led_cdev' set but not used [-Wunused-but-set-variable]
struct led_classdev *led_cdev;
^~~~~~~~
Get rid of it.
Fixes: commit 079933dbcb ("[media] v4l: flash led class: Fix of_node release in probe() error path")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The sub-device's OF node was used (of_node_get()) if it was set, but
device's OF node was always put. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the case of coda_firmware_request() failure, we should release the
prevously acquired resources.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch derives from previous one(s) by CrazyCat. I used the commit adding rev.3 to mainline Linux kernel as an example, so credits go to its author(s).
The hardware seems to scan and tune OK.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Simplify the remove function and the error path in the probe function by
using the managed versions of rc_allocate_device and rc_register_device.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Introduce managed versions of both functions.
They allows to simplify the error path in the probe function of
rc drivers, and usually also to simplify the remove function.
New element managed_alloc in struct rc_dev is needed to correctly
handle mixed use, e.g. managed version of rc_register_device and
normal version of rc_allocate_device.
In addition devm_rc_allocate_device sets rc->dev.parent as having a
reference to the parent device might be useful for future extensions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If a new vb buf is added to vb queue, the queue is
empty and steaming, dma should be started.
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Changing available_protocols to atomic64_t allows to get rid of the
mutex protecting access to the variable. This helps to simplify
the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
During sensors binding, there is a window where the sensor is switched
off, while there is a call it to set a new format, which can end up in
an access to the sensor, especially an I2C based sensor.
Remove this window by activating the sensor.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously, width of 720 was used, but it gives 16-pixel wide black bar
at right side of encoded picture.
Signed-off-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix to return error code -ENODEV from the error handling case
instead of 0(err maybe overwrited to 0 in the for loop), as
done elsewhere in this function.
[mchehab@s-opensource.com: remove a now uneeded set for err = -ENODEV]
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix to return error code -EINVAL from the platform_get_resource() error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It's not necessary to free memory allocated with devm_kzalloc
and using kfree leads to a double free.
Fixes: 7aae6e2df1 ("[media] Add GS1662 driver, a video serializer")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Moving the pxa_camera driver from soc_camera lots the implied
VIDEO_V4L2 Kconfig dependency, and building the driver without
V4L2 results in a kernel that cannot link:
drivers/media/platform/pxa_camera.o: In function `pxa_camera_remove':
pxa_camera.c:(.text.pxa_camera_remove+0x10): undefined reference to `v4l2_clk_unregister'
pxa_camera.c:(.text.pxa_camera_remove+0x18): undefined reference to `v4l2_device_unregister'
drivers/media/platform/pxa_camera.o: In function `pxa_camera_probe':
pxa_camera.c:(.text.pxa_camera_probe+0x458): undefined reference to `v4l2_of_parse_endpoint'
drivers/media/v4l2-core/videobuf2-core.o: In function `__enqueue_in_driver':
drivers/media/v4l2-core/videobuf2-core.o: In function `vb2_core_streamon':
videobuf2-core.c:(.text.vb2_core_streamon+0x1b4): undefined reference to `v4l_vb2q_enable_media_source'
drivers/media/v4l2-core/videobuf2-v4l2.o: In function `vb2_ioctl_reqbufs':
videobuf2-v4l2.c:(.text.vb2_ioctl_reqbufs+0xc): undefined reference to `video_devdata'
This adds back an explicit dependency.
Fixes: 3050b99850 ("[media] media: platform: pxa_camera: move pxa_camera out of soc_camera")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is only one waiter for the completion, therefore there is no need
to use complete_all(). Let's make that clear by using complete() instead
of complete_all().
While we are at it, we do a small optimization with the reinitialization
of the completion before we use it.
The usage pattern of the completion is:
waiter context waker context
send_packet()
init_completion()
usb_submit_urb()
wait_for_completion_interruptible()
usb_tx_callback()
complete()
imon_disonnect()
complete()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use a type with explicit endianness in machine to big endian conversion.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Documentation states that the "default-input" property should reside
directly in the node of the device. This adjusts the parsing to make the
implementation consistent with the documentation.
Based on patch by William Towle <william.towle@codethink.co.uk>.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The advertised V4L2 pixel format and Media Bus code don't match.
The current media bud code advertised is MEDIA_BUS_FMT_YUYV8_2X8
which does not reflect what the encoder actually outputs.
This encoder generate MEDIA_BUS_FMT_UYVY8_2X8 so advertise as such.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Function ite_set_carrier_params() uses variable use_demodulator after
having initialized it to false in some if branches, but this variable is
never set to true otherwise.
This bug has been found using clang -Wsometimes-uninitialized warning
flag.
Fixes: 620a32bba4 ("[media] rc: New rc-based ite-cir driver for
several ITE CIRs")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In mb86a20s_read_status_and_stats(), when mb86a20s_read_status() fails,
the function returns the value in variable rc without initializing it
first. Fix this by propagating the error code from variable status_nr.
This bug has been found using clang and -Wsometimes-uninitialized
warning flag.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
TechnoTrend TT-connect S2-4650 CI seems to be a variation of
the DVBSky S960CI device.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The variable name is always assigned to a literal string in the
proceeding switch statement, so it is never null and hence the
null check is redundant. Remove null the check.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Benoit Parrot