This patch cleans up the way device tree support is added in mdio-gpio
driver. I found lot of code duplication which is not necessary.
Also strangely a new platform driver was also introduced for device tree
support. All this forced me to do this cleanup patch.
After this patch, the driver probe checks the of_node pointer to get the
data from device tree.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an initial merge in of Eric Biederman's work to start adding
user namespace support to the networking.
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
1. Change the TX path to stop queues earlier and avoid returning
NETDEV_TX_BUSY.
2. Remove some inefficiencies in soft-TSO.
3. Fix various bugs involving device state transitions and/or reset
scheduling by error handlers.
4. Take advantage of my previous change to operstate initialisation.
5. Miscellaneous cleanup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This is a batch of updates intended for 3.7. The bulk of it is
mac80211 changes, including some mesh work from Thomas Pederson and
some multi-channel work from Johannes. A variety of driver updates
and other bits are scattered in there as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Following commit 8f4cccb ('net: Set device operstate at registration
time') it is now correct and preferable to set the carrier off before
registering a device.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We also stop clearing *efx in efx_init_struct(). This is safe because
alloc_etherdev_mq() already clears it for us.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
RX DMA is limited by the length specified in each descriptor and not
by the MAC. Over-length frames may get into the RX FIFO regardless of
the MAC settings, due to a hardware bug, but they will be truncated by
the packet DMA engine and reported as such in the completion event.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We try to defer resets while the device is not READY, but we're not
doing this quite correctly. In particular, changes to efx_nic::state
are documented as serialised by the RTNL lock, but they aren't.
1. We check whether a reset was requested during probe (suggesting
broken hardware) before we allow requested resets to be scheduled.
This leaves a window where a requested reset would be deferred
indefinitely.
2. Although we cancel the reset work item during device removal,
there are still later operations that can cause it to be scheduled
again. We need to check the state before scheduling it.
3. Since the state can change between scheduling and running of
the work item, we still need to check it there, and we need to
do so *after* acquiring the RTNL lock which serialises state
changes.
4. We must cancel the reset work item during device removal, if the
state could ever have been READY. This wasn't done in some of the
failure paths from efx_pci_probe(). Move the cancellation to
efx_pci_remove_main().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The current informational message doesn't properly explain what
happens, and could also appear if we defer a reset during
suspend/resume.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_change_mtu() and efx_realloc_channels() each stop and start much
of the NIC, even if it has been disabled. Since efx_start_all() is a
no-op when the NIC is disabled, this is probably harmless in the case
of efx_change_mtu(), but efx_realloc_channels() also reenables
interrupts which could be a bad thing to do.
Change efx_start_all() and efx_start_interrupts() to assert that the
NIC is not disabled, but make efx_stop_interrupts() do nothing if the
NIC is disabled (since it is already stopped), consistent with
efx_stop_all().
Update comments for efx_start_all() and efx_stop_all() to describe
their purpose and preconditions more accurately.
Add a common function to check and log if the NIC is disabled, and use
it in efx_net_open(), efx_change_mtu() and efx_realloc_channels().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Interrupt state should be consistently guarded by the RTNL lock once
the net device is registered.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
I don't think these PM functions can race with userland net device
operations, but it's much easier to reason about locking if state is
consistently guarded by the same lock.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
STATE_INIT and STATE_FINI are equivalent and represent incompletely
initialised states; combine them as STATE_UNINIT.
Rename STATE_RUNNING to STATE_READY, to avoid confusion with
netif_running() and IFF_RUNNING.
The comments do not quite match current usage, but this will be
corrected in subsequent fixes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We only use tso_state::full_packet_space to calculate the IPv4 tot_len
or IPv6 payload_len, not to set tso_state::packet_space. Replace it
with an ip_base_len field holding the value of tot_len or payload_len
before including the TCP payload, which is much more useful when
constructing the new headers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
TSO header buffers contain a control structure immediately followed by
the packet headers, and are kept on a free list when not in use. This
complicates buffer management and tends to result in cache read misses
when we recycle such buffers (particularly if DMA-coherent memory
requires caches to be disabled).
Replace the free list with a simple mapping by descriptor index. We
know that there is always a payload descriptor between any two
descriptors with TSO header buffers, so we can allocate only one
such buffer for each two descriptors.
While we're at it, use a standard error code for allocation failure,
not -1.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We now have a definite upper bound on the number of descriptors per
skb; use that to stop the queue when the next packet might not fit.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add a flags field to struct efx_tx_buffer, replacing the
continuation and map_single booleans.
Since a single descriptor cannot be both a TSO header and the last
descriptor for an skb, unionise efx_tx_buffer::{skb,tsoh} and add
flags for validity of these fields.
Clear all flags in free buffers (whereas previously the continuation
flag would be set).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
When no one is listening on NL socket, -ESRCH is returned and warning
message is printed. This message is confusing people and in fact has no
meaning. So do not print it in this case.
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using eth_hw_addr_random() to generate a random Ethernet address
(MAC) to be used by a net device and set addr_assign_type.
Not need to duplicating its implementation.
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using eth_hw_addr_random() to generate a random Ethernet address
(MAC) to be used by a net device and set addr_assign_type.
Not need to duplicating its implementation.
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using is_zero_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is all
zeros.
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to fsl_pq_mdio.c, this driver is for the 10G MDIO controller on
Freescale Frame Manager Ethernet controllers.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper functions which translate IEEE MDIO Manageable Device (MMD)
Energy-Efficient Ethernet (EEE) registers 3.20, 7.60 and 7.61 to and from
the comparable ethtool supported/advertised settings will be needed by
drivers other than those in PHYLIB (e.g. e1000e in a follow-on patch).
In the same fashion as similar translation functions in linux/mii.h, move
these functions from the PHYLIB core to the linux/mdio.h header file so the
code will not have to be duplicated in each driver needing MMD-to-ethtool
(and vice-versa) translations. The function and some variable names have
been renamed to be more descriptive.
Not tested on the only hardware that currently calls the related functions,
stmmac, because I don't have access to any. Has been compile tested and
the translations have been tested on a locally modified version of e1000e.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the "bonding" driver does not support load balancing outgoing
traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4)
are currently supported; this patch adds transmit hashing for IPv6 (and
TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the
bonding driver. In addition, bounds checking has been added to all
transmit hashing functions.
The algorithm chosen (xor'ing the bottom three quads of the source and
destination addresses together, then xor'ing each byte of that result into
the bottom byte, finally xor'ing with the last bytes of the MAC addresses)
was selected after testing almost 400,000 unique IPv6 addresses harvested
from server logs. This algorithm had the most even distribution for both
big- and little-endian architectures while still using few instructions. Its
behavior also attempts to closely match that of the IPv4 algorithm.
The IPv6 flow label was intentionally not included in the hash as it appears
to be unset in the vast majority of IPv6 traffic sampled, and the current
algorithm not using the flow label already offers a very even distribution.
Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets,
ie, they are not balanced based on layer 4 information. Additionally,
IPv6 packets with intermediate headers are not balanced based on layer
4 information. In practice these intermediate headers are not common and
this should not cause any problems, and the alternative (a packet-parsing
loop and look-up table) seemed slow and complicated for little gain.
Tested-by: John Eaglesham <linux@8192.net>
Signed-off-by: John Eaglesham <linux@8192.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to ethtool.h, e1000, e1000e, and igb to
implement MDI/MDIx control.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking update from David Miller:
"A couple weeks of bug fixing in there. The largest chunk is all the
broken crap Amerigo Wang found in the netpoll layer."
1) netpoll and it's users has several serious bugs:
a) uses GFP_KERNEL with locks held
b) interfaces requiring interrupts disabled are called with them
enabled
c) and vice versa
d) VLAN tag demuxing, as per all other RX packet input paths, is not
applied
All from Amerigo Wang.
2) Hopefully cure the ipv4 mapped ipv6 address TCP early demux bugs for
good, from Neal Cardwell.
3) Unlike AF_UNIX, AF_PACKET sockets don't set a default credentials
when the user doesn't specify one explicitly during sendmsg().
Instead we attach an empty (zero) SCM credential block which is
definitely not what we want. Fix from Eric Dumazet.
4) IPv6 illegally invokes netdevice notifiers with RCU lock held, fix
from Ben Hutchings.
5) inet_csk_route_child_sock() checks wrong inet options pointer, fix
from Christoph Paasch.
6) When AF_PACKET is used for transmit, packet loopback doesn't behave
properly when a socket fanout is enabled, from Eric Leblond.
7) On bluetooth l2cap channel create failure, we leak the socket, from
Jaganath Kanakkassery.
8) Fix all the netprio file handling bugs found by Al Viro, from John
Fastabend.
9) Several error return and NULL deref bug fixes in networking drivers
from Julia Lawall.
10) A large smattering of struct padding et al. kernel memory leaks to
userspace found of Mathias Krause.
11) Conntrack expections in netfilter can access an uninitialized timer,
fix from Pablo Neira Ayuso.
12) Several netfilter SIP tracker bug fixes from Patrick McHardy.
13) IPSEC ipv6 routes are not initialized correctly all the time,
resulting in an OOPS in inet_putpeer(). Also from Patrick McHardy.
14) Bridging does rcu_dereference() outside of RCU protected area, from
Stephen Hemminger.
15) Fix routing cache removal performance regression when looking up
output routes that have a local destination. From Zheng Yan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
af_netlink: force credentials passing [CVE-2012-3520]
ipv4: fix ip header ident selection in __ip_make_skb()
ipv4: Use newinet->inet_opt in inet_csk_route_child_sock()
tcp: fix possible socket refcount problem
net: tcp: move sk_rx_dst_set call after tcp_create_openreq_child()
net/core/dev.c: fix kernel-doc warning
netconsole: remove a redundant netconsole_target_put()
net: ipv6: fix oops in inet_putpeer()
net/stmmac: fix issue of clk_get for Loongson1B.
caif: Do not dereference NULL in chnl_recv_cb()
af_packet: don't emit packet on orig fanout group
drivers/net/irda: fix error return code
drivers/net/wan/dscc4.c: fix error return code
drivers/net/wimax/i2400m/fw.c: fix error return code
smsc75xx: add missing entry to MAINTAINERS
net: qmi_wwan: new devices: UML290 and K5006-Z
net: sh_eth: Add eth support for R8A7779 device
netdev/phy: skip disabled mdio-mux nodes
dt: introduce for_each_available_child_of_node, of_get_next_available_child
net: netprio: fix cgrp create and write priomap race
...
Because the hardware reports whenever an frame
was either at the start, in the middle or at
the end of a A-MPDU, we can easily report the
information for radiotap.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of changes in the supported rates set for a given station, it is now
possible to use this callback to update the current internal state of the
station in the htc driver.
Reported-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When unregistered with mac80211, we can't call its functionality
for FW restart, so avoid it and prevent automatic FW restart for
the init firmware.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no need to check if the ownership has been
relinquished but we should rather try to get it in a
loop.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is the implementation for igb to allow forcing MDI state
via ethtool, allowing users to work around some improperly
behaving switches.
Forcing in this driver is for now only allowed when auto-neg is
enabled.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown aaron.f.brown@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some users report issues with link failing when connected to certain
switches. This gives the user the ability to control the MDI state
from the driver, allowing users to work around some improperly
behaving switches.
Forcing in this driver is for now only allowed when auto-neg is
enabled.
This is in regards to the related ethtool app patch and
bugzilla.kernel.org bug 11998
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: bruce.w.allan@intel.com
CC: n.poppelier@xs4all.nl
CC: bastien@durel.org
CC: jsveiga@it.eng.br
Tested-by: Aaron Brown aaron.f.brown@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the implementation in e1000 to allow ethtool to force
MDI state, allowing users to work around some improperly
behaving switches.
Forcing in this driver is for now only allowed when auto-neg is enabled.
To use must have the matching version of ethtool app that supports
this functionality.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown aaron.f.brown@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order for igb to support MDI setting support via
ethtool this code is needed to allow setting the MDI state
via software.
This is in regards to the related ethtool patch
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown aaron.f.brown@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order for e1000e to support MDI setting support via
ethtool this code is needed to allow setting the MDI state
via software.
This is in regards to the related ethtool patch and
fixes bugzilla.kernel.org bug 11998
Signed-off-by: Bruce W Allan <bruce.w.allan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown aaron.f.brown@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Here are 10 more USB patches for 3.6-rc3. They all fix reported
problems (build problems for one of them, and easily repeatable oopses
for the others.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAyjj4ACgkQMUfUDdst+yn8gQCgkNpc92Ux5hBYJIX/AQYoBrTB
ktAAoLiXxIhVP+D4C42R1VLw9vGeB1QH
=+8kb
-----END PGP SIGNATURE-----
Merge tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull more USB patches from Greg Kroah-Hartman:
"Here are 10 more USB patches for 3.6-rc3. They all fix reported
problems (build problems for one of them, and easily repeatable oopses
for the others.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
gpu/mfd/usb: Fix USB randconfig problems
USB: CDC ACM: Fix NULL pointer dereference
USB: emi62: remove __devinit* from the struct usb_device_id table
USB: winbond: remove __devinit* from the struct usb_device_id table
USB: vt6656: remove __devinit* from the struct usb_device_id table
USB: rtl8187: remove __devinit* from the struct usb_device_id table
USB: p54usb: remove __devinit* from the struct usb_device_id table
USB: spca506: remove __devinit* from the struct usb_device_id table
USB: jl2005bcd: remove __devinit* from the struct usb_device_id table
USB: smsusb: remove __devinit* from the struct usb_device_id table
This netconsole_target_put() is obviously redundant, and it
causes a kernel segfault when removing a bridge device which has
netconsole running on it.
This is caused by:
commit 8d8fc29d02
Author: Amerigo Wang <amwang@redhat.com>
Date: Thu May 19 21:39:10 2011 +0000
netpoll: disable netpoll when enslave a device
Cc: David Miller <davem@davemloft.net>
(for all 3.x stable releases)
Cc: stable@vger.kernel.org
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When getting clock, give a chance to the CPUs without DT support,
which use Common Clock Framework, such as Loongson1B.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is resolved by two things:
1) allow dev_addr of different length than ETH_ALEN
2) during port add, check for dev->type and change it if necessary
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e1,e2;
@@
if (ret < 0)
{ ... return ret; }
... when != ret = e1
when forall
*if(...)
{
... when != ret = e2
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move up the initialization of rc so that failure of pci_alloc_consistent
returns -ENOMEM as well.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e1,e2;
@@
if (ret < 0)
{ ... return ret; }
... when != ret = e1
when forall
*if(...)
{
... when != ret = e2
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Srinivas Kandagatla