If DRBD lost all path to good data,
and the on-no-data-accessible policy is OND_SUSPEND_IO,
all pending and new IO requests are suspended (will block).
If that setting is OND_IO_ERROR, IO will still be completed.
READ to "clean" areas (e.g. on an D_INCONSISTENT device,
and bitmap indicates a block is already in sync) will succeed.
READ to "unclean" areas (bitmap indicates block is out-of-sync),
will return EIO.
If we are already D_DISKLESS (or D_FAILED), we also return EIO.
Unfortunately, on a former R_PRIMARY C_SYNC_TARGET D_INCONSISTENT,
after replication link loss, new WRITE requests still went through OK.
The would also set the "out-of-sync" bit on their way, so READ after
WRITE would still return EIO. Also, the data generation UUIDs had not
been bumped, we would cause data divergence, without being able to
detect it on the next sync handshake, given the right sequence of events
in a multiple error scenario and "improper" order of recovery actions.
The right thing to do is to return EIO for all new writes,
unless we have access to good, current, D_UP_TO_DATE data.
The "established best practices" way to avoid these situations in the
first place is to set OND_SUSPEND_IO, or even do a hard-reset from
the pri-on-incon-degr policy helper hook.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Possibly sequence of events:
SyncTarget is made Primary, then loses replication link
(only path to good data on SyncSource).
Behavior is then controlled by the on-no-data-accessible policy,
which defaults to OND_IO_ERROR (may be set to OND_SUSPEND_IO).
If OND_IO_ERROR is in fact the current policy, we clear the susp_fen
(IO suspended due to fencing policy) flag, do NOT set the susp_nod
(IO suspended due to no data) flag.
But we forgot to call the IO error completion for all pending,
suspended, requests.
While at it, also add a race check for a theoretically possible
race with a new handshake (network hickup), we may be able to
re-send requests, and can avoid passing IO errors up the stack.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When resync is finished, we already call the "after-resync-target"
handler (on the former sync target, obviously), once per volume.
Paired with the before-resync-target handler, you can create snapshots,
before the resync causes the volumes to become inconsistent,
and discard those snapshots again, once they are no longer needed.
It was also overloaded to be paired with the "fence-peer" handler,
to "unfence" once the volumes are up-to-date and known good.
This has some disadvantages, though: we call "fence-peer" for the whole
connection (once for the group of volumes), but would call unfence as
side-effect of after-resync-target once for each volume.
Also, we fence on a (current, or about to become) Primary,
which will later become the sync-source.
Calling unfence only as a side effect of the after-resync-target
handler opens a race window, between a new fence on the Primary
(SyncTarget) and the unfence on the SyncTarget, which is difficult to
close without some kind of "cluster wide lock" in those handlers.
We would not need those handlers if we could still communicate.
Which makes trying to aquire a cluster wide lock from those handlers
seem like a very bad idea.
This introduces the "unfence-peer" handler, which will be called
per connection (once for the group of volumes), just like the fence
handler, only once all volumes are back in sync, and on the SyncSource.
Which is expected to be the node that previously called "fence", the
node that is currently allowed to be Primary, and thus the only node
that could trigger a new "fence" that could race with this unfence.
Which makes us not need any cluster wide synchronization here,
serializing two scripts running on the same node is trivial.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If the replication link breaks exactly during "resync finished" detection,
finishing too early on the sync source could again lead to UUIDs rotated
too fast, and potentially a spurious full resync on next handshake.
Always wait for explicit resync finished state change notification from
the sync target.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Make sure we have at least 67 (> AL_UPDATES_PER_TRANSACTION)
al-extents available, and allow up to half of that to be
discarded in one bio.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For consistency, also zero-out partial unaligned chunks of discard
requests on the local backend.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we have the discard_zeroes_if_aligned setting, we should also
check it when setting up our queue parameters on the primary,
not only on the receiving side.
We announce discard support,
UNLESS
* we are connected to a peer that does not support TRIM
on the DRBD protocol level. Otherwise, it would either discard, or
do a fallback to zero-out, depending on its backend and configuration.
* our local backend does not support discards,
or (discard_zeroes_data=0 AND discard_zeroes_if_aligned=no).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We can avoid spurious data divergence caused by partially-ignored
discards on certain backends with discard_zeroes_data=0, if we
translate partial unaligned discard requests into explicit zero-out.
The relevant use case is LVM/DM thin.
If on different nodes, DRBD is backed by devices with differing
discard characteristics, discards may lead to data divergence
(old data or garbage left over on one backend, zeroes due to
unmapped areas on the other backend). Online verify would now
potentially report tons of spurious differences.
While probably harmless for most use cases (fstrim on a file system),
DRBD cannot have that, it would violate our promise to upper layers
that our data instances on the nodes are identical.
To be correct and play safe (make sure data is identical on both copies),
we would have to disable discard support, if our local backend (on a
Primary) does not support "discard_zeroes_data=true".
We'd also have to translate discards to explicit zero-out on the
receiving (typically: Secondary) side, unless the receiving side
supports "discard_zeroes_data=true".
Which both would allocate those blocks, instead of unmapping them,
in contrast with expectations.
LVM/DM thin does set discard_zeroes_data=0,
because it silently ignores discards to partial chunks.
We can work around this by checking the alignment first.
For unaligned (wrt. alignment and granularity) or too small discards,
we zero-out the initial (and/or) trailing unaligned partial chunks,
but discard all the aligned full chunks.
At least for LVM/DM thin, the result is effectively "discard_zeroes_data=1".
Arguably it should behave this way internally, by default,
and we'll try to make that happen.
But our workaround is still valid for already deployed setups,
and for other devices that may behave this way.
Setting discard-zeroes-if-aligned=yes will allow DRBD to use
discards, and to announce discard_zeroes_data=true, even on
backends that announce discard_zeroes_data=false.
Setting discard-zeroes-if-aligned=no will cause DRBD to always
fall-back to zero-out on the receiving side, and to not even
announce discard capabilities on the Primary, if the respective
backend announces discard_zeroes_data=false.
We used to ignore the discard_zeroes_data setting completely.
To not break established and expected behaviour, and suddenly
cause fstrim on thin-provisioned LVs to run out-of-space,
instead of freeing up space, the default value is "yes".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
To maintain write-order fidelity accros all volumes in a DRBD resource,
the receiver of a P_BARRIER needs to issue flushes to all volumes.
We used to do this by calling blkdev_issue_flush(), synchronously,
one volume at a time.
We now submit all flushes to all volumes in parallel, then wait for all
completions, to reduce worst-case latencies on multi-volume resources.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The command line parameter the kernel module uses to communicate the
device minor to userland helper is flawed in a way that the device
indentifier "minor-%d" is being truncated to minors with a maximum
of 5 digits.
But DRBD 8.4 allows 2^20 == 1048576 minors,
thus a minimum of 7 digits must be supported.
Reported by Veit Wahlich on drbd-dev.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Regression introduced with 8.4.5
drbd: application writes may set-in-sync in protocol != C
Overwriting the same block (LBA) while a former version is still
"in-flight" to the peer (to be exact: we did not receive the
P_BARRIER_ACK for its epoch yet) would wait for the full epoch of that
former version to be acknowledged by the peer.
In synchronous and quasi-synchronous protocols C and B,
this may double the latency on overwrites.
With protocol A, which is supposed to be asynchronous and only wait for
local completion, it is even worse: it would make overwrites
quasi-synchronous, they would be hit by the full RTT, which protocol A
was specifically meant to avoid, and possibly the additional time it
takes to drain the buffers first.
Particularly bad for databases, or anything else that
does frequent updates to the same blocks (various file system meta data).
No impact if >= rtt passes between updates to the same block.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If thinly provisioned volumes are used, during a resync the sync source
tries to find out if a block is deallocated. If it is deallocated, then
the resync target uses block_dev_issue_zeroout() on the range in
question.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
As long as the value is 0 the feature is disabled. With setting
it to a positive value, DRBD limits and aligns its resync requests
to the rs-discard-granularity setting. If the sync source detects
all zeros in such a block, the resync target discards the range
on disk.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If during resync we read only zeroes for a range of sectors assume
that these secotors can be discarded on the sync target node.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When leaving resync states because of disconnect,
do the bitmap write-out synchronously in the drbd_disconnected() path.
When leaving resync states because we go back to AHEAD/BEHIND, or
because resync actually finished, or some disk was lost during resync,
trigger the write-out from after_state_ch().
The bitmap write-out for resync -> ahead/behind was missing completely before.
Note that this is all only an optimization to avoid double-resyncs of
already completed blocks in case this node crashes.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The intention was to only suspend IO if some normal bitmap operation is
supposed to be locked out, not always. If the bulk operation is flaged
as BM_LOCKED_CHANGE_ALLOWED, we do not need to suspend IO.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Use BIO_MAX_PAGES instead and we will remove BIO_MAX_SIZE.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of overloading the discard support with the REQ_SECURE flag.
Use the opportunity to rename the queue flag as well, and remove the
dead checks for this flag in the RAID 1 and RAID 10 drivers that don't
claim support for secure erase.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Because we define WRITE/READ as REQ_OPs, we cannot do
switch (rq_data_dir(request))
case READ
....
case WRITE
...
without getting warnings about handling other REQ_OPs.
This just has mq_disk do a if/else like it does in other
places.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
After a migrate to another host (which may not have multiqueue
support), the number of rings (block hardware queues)
may be changed and the ring info structure will also be reallocated.
This patch fixes two related bugs:
* call blk_mq_update_nr_hw_queues() to make blk-core know the number
of hardware queues have been changed.
* Don't store rinfo pointer to hctx->driver_data, because rinfo may be
reallocated so use hctx->queue_num to get the rinfo structure instead.
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Sometimes blkfront may twice receive blkback_changed() notification
(XenbusStateConnected) after migration, which will cause
talk_to_blkback() to be called twice too and confuse xen-blkback.
The flow is as follow:
blkfront blkback
blkfront_resume()
> talk_to_blkback()
> Set blkfront to XenbusStateInitialised
front changed()
> Connect()
> Set blkback to XenbusStateConnected
blkback_changed()
> Skip talk_to_blkback()
because frontstate == XenbusStateInitialised
> blkfront_connect()
> Set blkfront to XenbusStateConnected
-----
And here we get another XenbusStateConnected notification leading
to:
-----
blkback_changed()
> because now frontstate != XenbusStateInitialised
talk_to_blkback() is also called again
> blkfront state changed from
XenbusStateConnected to XenbusStateInitialised
(Which is not correct!)
front_changed():
> Do nothing because blkback
already in XenbusStateConnected
Now blkback is in XenbusStateConnected but blkfront is still
in XenbusStateInitialised - leading to no disks.
Poking of the XenbusStateConnected state is allowed (to deal with
block disk change) and has to be dealt with. The most likely
cause of this bug are custom udev scripts hooking up the disks
and then validating the size.
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We were passing in &nbd for the private data in debugfs_create_file() for the
flags entry. We expect it to just be nbd, fix this so we get proper output from
this debugfs entry.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
To avoid confusion between REQ_OP_FLUSH, which is handled by
request_fn drivers, and upper layers requesting the block layer
perform a flush sequence along with possibly a WRITE, this patch
renames REQ_FLUSH to REQ_PREFLUSH.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The last patch added a REQ_OP_FLUSH for request_fn drivers
and the next patch renames REQ_FLUSH to REQ_PREFLUSH which
will be used by file systems and make_request_fn drivers so
they can send a write/flush combo.
This patch drops xen's use of REQ_FLUSH to track if it supports
REQ_OP_FLUSH requests, so REQ_FLUSH can be deleted.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Juergen Gross <kernel@pfupf.net>
Signed-off-by: Jens Axboe <axboe@fb.com>
This adds a REQ_OP_FLUSH operation that is sent to request_fn
based drivers by the block layer's flush code, instead of
sending requests with the request->cmd_flags REQ_FLUSH bit set.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The req operation REQ_OP is separated from the rq_flag_bits
definition. This converts the block layer drivers to
use req_op to get the op from the request struct.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Separate the op from the rq_flag_bits and have xen
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Separate the op from the rq_flag_bits and have drbd
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch converts the simple bi_rw use cases in the block,
drivers, mm and fs code to set/get the bio operation using
bio_set_op_attrs/bio_op
These should be simple one or two liner cases, so I just did them
in one patch. The next patches handle the more complicated
cases in a module per patch.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We currently set REQ_WRITE/WRITE for all non READ IOs
like discard, flush, writesame, etc. In the next patches where we
no longer set up the op as a bitmap, we will not be able to
detect a operation direction like writesame by testing if REQ_WRITE is
set.
This patch converts the drivers and cgroup to use the
op_is_write helper. This should just cover the simple
cases. I did dm, md and bcache in their own patches
because they were more involved.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This has callers of submit_bio/submit_bio_wait set the bio->bi_rw
instead of passing it in. This makes that use the same as
generic_make_request and how we set the other bio fields.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixed up fs/ext4/crypto.c
Signed-off-by: Jens Axboe <axboe@fb.com>
- Until now, dax has been disabled if media errors were found on
any device. This enables the use of DAX in the presence of these
errors by making all sector-aligned zeroing go through the driver.
- The driver (already) has the ability to clear errors on writes that
are sent through the block layer using 'DSMs' defined in ACPI 6.1.
Other misc changes:
- When mounting DAX filesystems, check to make sure the partition
is page aligned. This is a requirement for DAX, and previously, we
allowed such unaligned mounts to succeed, but subsequent reads/writes
would fail.
- Misc/cleanup fixes from Jan that remove unused code from DAX related to
zeroing, writeback, and some size checks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=v6Of
-----END PGP SIGNATURE-----
Merge tag 'dax-misc-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull misc DAX updates from Vishal Verma:
"DAX error handling for 4.7
- Until now, dax has been disabled if media errors were found on any
device. This enables the use of DAX in the presence of these
errors by making all sector-aligned zeroing go through the driver.
- The driver (already) has the ability to clear errors on writes that
are sent through the block layer using 'DSMs' defined in ACPI 6.1.
Other misc changes:
- When mounting DAX filesystems, check to make sure the partition is
page aligned. This is a requirement for DAX, and previously, we
allowed such unaligned mounts to succeed, but subsequent
reads/writes would fail.
- Misc/cleanup fixes from Jan that remove unused code from DAX
related to zeroing, writeback, and some size checks"
* tag 'dax-misc-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: fix a comment in dax_zero_page_range and dax_truncate_page
dax: for truncate/hole-punch, do zeroing through the driver if possible
dax: export a low-level __dax_zero_page_range helper
dax: use sb_issue_zerout instead of calling dax_clear_sectors
dax: enable dax in the presence of known media errors (badblocks)
dax: fallback from pmd to pte on error
block: Update blkdev_dax_capable() for consistency
xfs: Add alignment check for DAX mount
ext2: Add alignment check for DAX mount
ext4: Add alignment check for DAX mount
block: Add bdev_dax_supported() for dax mount checks
block: Add vfs_msg() interface
dax: Remove redundant inode size checks
dax: Remove pointless writeback from dax_do_io()
dax: Remove zeroing from dax_io()
dax: Remove dead zeroing code from fault handlers
ext2: Avoid DAX zeroing to corrupt data
ext2: Fix block zeroing in ext2_get_blocks() for DAX
dax: Remove complete_unwritten argument
DAX: move RADIX_DAX_ definitions to dax.c
Pull Ceph updates from Sage Weil:
"This changeset has a few main parts:
- Ilya has finished a huge refactoring effort to sync up the
client-side logic in libceph with the user-space client code, which
has evolved significantly over the last couple years, with lots of
additional behaviors (e.g., how requests are handled when cluster
is full and transitions from full to non-full).
This structure of the code is more closely aligned with userspace
now such that it will be much easier to maintain going forward when
behavior changes take place. There are some locking improvements
bundled in as well.
- Zheng adds multi-filesystem support (multiple namespaces within the
same Ceph cluster)
- Zheng has changed the readdir offsets and directory enumeration so
that dentry offsets are hash-based and therefore stable across
directory fragmentation events on the MDS.
- Zheng has a smorgasbord of bug fixes across fs/ceph"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (71 commits)
ceph: fix wake_up_session_cb()
ceph: don't use truncate_pagecache() to invalidate read cache
ceph: SetPageError() for writeback pages if writepages fails
ceph: handle interrupted ceph_writepage()
ceph: make ceph_update_writeable_page() uninterruptible
libceph: make ceph_osdc_wait_request() uninterruptible
ceph: handle -EAGAIN returned by ceph_update_writeable_page()
ceph: make fault/page_mkwrite return VM_FAULT_OOM for -ENOMEM
ceph: block non-fatal signals for fault/page_mkwrite
ceph: make logical calculation functions return bool
ceph: tolerate bad i_size for symlink inode
ceph: improve fragtree change detection
ceph: keep leaf frag when updating fragtree
ceph: fix dir_auth check in ceph_fill_dirfrag()
ceph: don't assume frag tree splits in mds reply are sorted
ceph: fix inode reference leak
ceph: using hash value to compose dentry offset
ceph: don't forbid marking directory complete after forward seek
ceph: record 'offset' for each entry of readdir result
ceph: define 'end/complete' in readdir reply as bit flags
...
For map check, we are going to need to send CEPH_MSG_MON_GET_VERSION
messages asynchronously and get a callback on completion. Refactor MON
client to allow firing off generic requests asynchronously and add an
async variant of ceph_monc_get_version(). ceph_monc_do_statfs() is
switched over and remains sync.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
This adds support and switches rbd to a new, more reliable version of
watch/notify protocol. As with the OSD client update, this is mostly
about getting the right structures linked into the right places so that
reconnects are properly sent when needed. watch/notify v2 also
requires sending regular pings to the OSDs - send_linger_ping().
A major change from the old watch/notify implementation is the
introduction of ceph_osd_linger_request - linger requests no longer
piggy back on ceph_osd_request. ceph_osd_event has been merged into
ceph_osd_linger_request.
All the details are now hidden within libceph, the interface consists
of a simple pair of watch/unwatch functions and ceph_osdc_notify_ack().
ceph_osdc_watch() does return ceph_osd_linger_request, but only to keep
the lifetime management simple.
ceph_osdc_notify_ack() accepts an optional data payload, which is
relayed back to the notifier.
Portions of this patch are loosely based on work by Douglas Fuller
<dfuller@redhat.com> and Mike Christie <michaelc@cs.wisc.edu>.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Introduce __rbd_dev_header_unwatch_sync(), which doesn't flush notify
callbacks. This is for the new rados_watcherrcb_t, which would be
called from a notify callback.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
finish_read(), its only user, uses it to get to hdr.data_len, which is
what ->r_result is set to on success. This gains us the ability to
safely call callbacks from contexts other than reply, e.g. map check.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The crux of this is getting rid of ceph_osdc_build_request(), so that
MOSDOp can be encoded not before but after calc_target() calculates the
actual target. Encoding now happens within ceph_osdc_start_request().
Also nuked is the accompanying bunch of pointers into the encoded
buffer that was used to update fields on each send - instead, the
entire front is re-encoded. If we want to support target->name_len !=
base->name_len in the future, there is no other way, because oid is
surrounded by other fields in the encoded buffer.
Encoding OSD ops and adding data items to the request message were
mixed together in osd_req_encode_op(). While we want to re-encode OSD
ops, we don't want to add duplicate data items to the message when
resending, so all call to ceph_osdc_msg_data_add() are factored out
into a new setup_request_data().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Switch to ceph_object_id and use ceph_oid_aprintf() instead of a bare
const char *. This reduces noise in rbd_dev_header_name().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Currently ceph_object_id can hold object names of up to 100
(CEPH_MAX_OID_NAME_LEN) characters. This is enough for all use cases,
expect one - long rbd image names:
- a format 1 header is named "<imgname>.rbd"
- an object that points to a format 2 header is named "rbd_id.<imgname>"
We operate on these potentially long-named objects during rbd map, and,
for format 1 images, during header refresh. (A format 2 header name is
a small system-generated string.)
Lift this 100 character limit by making ceph_object_id be able to point
to an externally-allocated string. Apart from being able to work with
almost arbitrarily-long named objects, this allows us to reduce the
size of ceph_object_id from >100 bytes to 64 bytes.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The size of ->r_request and ->r_reply messages depends on the size of
the object name (ceph_object_id), while the size of ceph_osd_request is
fixed. Move message allocation into a separate function that would
have to be called after ceph_object_id and ceph_object_locator (which
is also going to become variable in size with RADOS namespaces) have
been filled in:
req = ceph_osdc_alloc_request(...);
<fill in req->r_base_oid>
<fill in req->r_base_oloc>
ceph_osdc_alloc_messages(req);
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
By the time we get to checking for_each_obj_request_safe(img_request)
terminating condition, all obj_requests may be complete and img_request
ref, that rbd_img_request_submit() takes away from its caller, may be
put. Moving the next_obj_request cursor is then a use-after-free on
img_request.
It's totally benign, as the value that's read is never used, but
I think it's still worth fixing.
Cc: Alex Elder <elder@linaro.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
debug_stat sysfs is read-only and represents various debugging data that
zram developers may need. This file is not meant to be used by anyone
else: its content is not documented and will change any time w/o any
notice. Therefore, the output of debug_stat file contains a version
string. To avoid any confusion, we will increase the version number
every time we modify the output.
At the moment this file exports only one value -- the number of
re-compressions, IOW, the number of times compression fast path has
failed. This stat is temporary any will be useful in case if any
per-cpu compression streams regressions will be reported.
Link: http://lkml.kernel.org/r/20160513230834.GB26763@bbox
Link: http://lkml.kernel.org/r/20160511134553.12655-1-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the internal part of max_comp_streams interface, since we
switched to per-cpu streams. We will keep RW max_comp_streams attr
around, because:
a) we may (silently) switch back to idle compression streams list and
don't want to disturb user space
b) max_comp_streams attr must wait for the next 'lay off cycle'; we
give user space 2 years to adjust before we remove/downgrade the attr,
and there are already several attrs scheduled for removal in 4.11, so
it's too late for max_comp_streams.
This slightly change a user visible behaviour:
- First, reading from max_comp_stream file now will always return the
number of online CPUs.
- Second, writing to max_comp_stream will not take any effect.
Link: http://lkml.kernel.org/r/20160503165546.25201-1-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass GFP flags to zs_malloc() instead of using a fixed mask supplied to
zs_create_pool(), so we can be more flexible, but, more importantly, we
need this to switch zram to per-cpu compression streams -- zram will try
to allocate handle with preemption disabled in a fast path and switch to
a slow path (using different gfp mask) if the fast one has failed.
Apart from that, this also align zs_malloc() interface with zspool/zbud.
[sergey.senozhatsky@gmail.com: pass GFP flags to zs_malloc() instead of using a fixed mask]
Link: http://lkml.kernel.org/r/20160429150942.GA637@swordfish
Link: http://lkml.kernel.org/r/20160429150942.GA637@swordfish
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many developers already know that field for reference count of the
struct page is _count and atomic type. They would try to handle it
directly and this could break the purpose of page reference count
tracepoint. To prevent direct _count modification, this patch rename it
to _refcount and add warning message on the code. After that, developer
who need to handle reference count will find that field should not be
accessed directly.
[akpm@linux-foundation.org: fix comments, per Vlastimil]
[akpm@linux-foundation.org: Documentation/vm/transhuge.txt too]
[sfr@canb.auug.org.au: sync ethernet driver changes]
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Yuval Mintz <yuval.mintz@qlogic.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1/ If a mapping overlaps a bad sector fail the request.
2/ Do not opportunistically report more dax-capable capacity than is
requested when errors present.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[vishal: fix a conflict with system RAM collision patches]
[vishal: add a 'size' parameter to ->direct_access]
[vishal: fix a conflict with DAX alignment check patches]
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Support SPI based w5100 devices, from Akinobu Mita.
2) Partial Segmentation Offload, from Alexander Duyck.
3) Add GMAC4 support to stmmac driver, from Alexandre TORGUE.
4) Allow cls_flower stats offload, from Amir Vadai.
5) Implement bpf blinding, from Daniel Borkmann.
6) Optimize _ASYNC_ bit twiddling on sockets, unless the socket is
actually using FASYNC these atomics are superfluous. From Eric
Dumazet.
7) Run TCP more preemptibly, also from Eric Dumazet.
8) Support LED blinking, EEPROM dumps, and rxvlan offloading in mlx5e
driver, from Gal Pressman.
9) Allow creating ppp devices via rtnetlink, from Guillaume Nault.
10) Improve BPF usage documentation, from Jesper Dangaard Brouer.
11) Support tunneling offloads in qed, from Manish Chopra.
12) aRFS offloading in mlx5e, from Maor Gottlieb.
13) Add RFS and RPS support to SCTP protocol, from Marcelo Ricardo
Leitner.
14) Add MSG_EOR support to TCP, this allows controlling packet
coalescing on application record boundaries for more accurate
socket timestamp sampling. From Martin KaFai Lau.
15) Fix alignment of 64-bit netlink attributes across the board, from
Nicolas Dichtel.
16) Per-vlan stats in bridging, from Nikolay Aleksandrov.
17) Several conversions of drivers to ethtool ksettings, from Philippe
Reynes.
18) Checksum neutral ILA in ipv6, from Tom Herbert.
19) Factorize all of the various marvell dsa drivers into one, from
Vivien Didelot
20) Add VF support to qed driver, from Yuval Mintz"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1649 commits)
Revert "phy dp83867: Fix compilation with CONFIG_OF_MDIO=m"
Revert "phy dp83867: Make rgmii parameters optional"
r8169: default to 64-bit DMA on recent PCIe chips
phy dp83867: Make rgmii parameters optional
phy dp83867: Fix compilation with CONFIG_OF_MDIO=m
bpf: arm64: remove callee-save registers use for tmp registers
asix: Fix offset calculation in asix_rx_fixup() causing slow transmissions
switchdev: pass pointer to fib_info instead of copy
net_sched: close another race condition in tcf_mirred_release()
tipc: fix nametable publication field in nl compat
drivers: net: Don't print unpopulated net_device name
qed: add support for dcbx.
ravb: Add missing free_irq() calls to ravb_close()
qed: Remove a stray tab
net: ethernet: fec-mpc52xx: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fec-mpc52xx: use phydev from struct net_device
bpf, doc: fix typo on bpf_asm descriptions
stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set
net: ethernet: fs-enet: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fs-enet: use phydev from struct net_device
...
Pull block driver updates from Jens Axboe:
"On top of the core pull request, this is the drivers pull request for
this merge window. This contains:
- Switch drivers to the new write back cache API, and kill off the
flush flags. From me.
- Kill the discard support for the STEC pci-e flash driver. It's
trivially broken, and apparently unmaintained, so it's safer to
just remove it. From Jeff Moyer.
- A set of lightnvm updates from the usual suspects (Matias/Javier,
and Simon), and fixes from Arnd, Jeff Mahoney, Sagi, and Wenwei
Tao.
- A set of updates for NVMe:
- Turn the controller state management into a proper state
machine. From Christoph.
- Shuffling of code in preparation for NVMe-over-fabrics, also
from Christoph.
- Cleanup of the command prep part from Ming Lin.
- Rewrite of the discard support from Ming Lin.
- Deadlock fix for namespace removal from Ming Lin.
- Use the now exported blk-mq tag helper for IO termination.
From Sagi.
- Various little fixes from Christoph, Guilherme, Keith, Ming
Lin, Wang Sheng-Hui.
- Convert mtip32xx to use the now exported blk-mq tag iter function,
from Keith"
* 'for-4.7/drivers' of git://git.kernel.dk/linux-block: (74 commits)
lightnvm: reserved space calculation incorrect
lightnvm: rename nr_pages to nr_ppas on nvm_rq
lightnvm: add is_cached entry to struct ppa_addr
lightnvm: expose gennvm_mark_blk to targets
lightnvm: remove mgt targets on mgt removal
lightnvm: pass dma address to hardware rather than pointer
lightnvm: do not assume sequential lun alloc.
nvme/lightnvm: Log using the ctrl named device
lightnvm: rename dma helper functions
lightnvm: enable metadata to be sent to device
lightnvm: do not free unused metadata on rrpc
lightnvm: fix out of bound ppa lun id on bb tbl
lightnvm: refactor set_bb_tbl for accepting ppa list
lightnvm: move responsibility for bad blk mgmt to target
lightnvm: make nvm_set_rqd_ppalist() aware of vblks
lightnvm: remove struct factory_blks
lightnvm: refactor device ops->get_bb_tbl()
lightnvm: introduce nvm_for_each_lun_ppa() macro
lightnvm: refactor dev->online_target to global nvm_targets
lightnvm: rename nvm_targets to nvm_tgt_type
...
Pull core block layer updates from Jens Axboe:
"This is the core block IO changes for this merge window. Nothing
earth shattering in here, it's mostly just fixes. In detail:
- Fix for a long standing issue where wrong ordering in blk-mq caused
order_to_size() to spew a warning. From Bart.
- Async discard support from Christoph. Basically just splitting our
sync interface into a submit + wait part.
- Add a cleaner interface for flagging whether a device has a write
back cache or not. We've previously overloaded blk_queue_flush()
with this, but let's make it more explicit. Drivers cleaned up and
updated in the drivers pull request. From me.
- Fix for a double check for whether IO accounting is enabled or not.
From Michael Callahan.
- Fix for the async discard from Mike Snitzer, reinstating the early
EOPNOTSUPP return if the device doesn't support discards.
- Also from Mike, export bio_inc_remaining() so dm can drop it's
private copy of it.
- From Ming Lin, add support for passing in an offset for request
payloads.
- Tag function export from Sagi, which will be used in NVMe in the
drivers pull.
- Two blktrace related fixes from Shaohua.
- Propagate NOMERGE flag when making a request from a bio, also from
Shaohua.
- An optimization to not parse cgroup paths in blk-throttle, if we
don't need to. From Shaohua"
* 'for-4.7/core' of git://git.kernel.dk/linux-block:
blk-mq: fix undefined behaviour in order_to_size()
blk-throttle: don't parse cgroup path if trace isn't enabled
blktrace: add missed mask name
blktrace: delete garbage for message trace
block: make bio_inc_remaining() interface accessible again
block: reinstate early return of -EOPNOTSUPP from blkdev_issue_discard
block: Minor blk_account_io_start usage cleanup
block: add __blkdev_issue_discard
block: remove struct bio_batch
block: copy NOMERGE flag from bio to request
block: add ability to flag write back caching on a device
blk-mq: Export tagset iter function
block: add offset in blk_add_request_payload()
writeback: Fix performance regression in wb_over_bg_thresh()
The attribute 0 is never used in drbd, so let's use it as pad attribute
in netlink messages. This minimizes the patch.
Note that this patch is only compile-tested.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A while ago, commit 9875201e10 ("rbd: fix use-after free of
rbd_dev->disk") fixed rbd unmap vs notify race by introducing
an exported wrapper for flushing notifies and sticking it into
do_rbd_remove().
A similar problem exists on the rbd map path, though: the watch is
registered in rbd_dev_image_probe(), while the disk is set up quite
a few steps later, in rbd_dev_device_setup(). Nothing prevents
a notify from coming in and crashing on a NULL rbd_dev->disk:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
Call Trace:
[<ffffffffa0508344>] rbd_watch_cb+0x34/0x180 [rbd]
[<ffffffffa04bd290>] do_event_work+0x40/0xb0 [libceph]
[<ffffffff8109d5db>] process_one_work+0x17b/0x470
[<ffffffff8109e3ab>] worker_thread+0x11b/0x400
[<ffffffff8109e290>] ? rescuer_thread+0x400/0x400
[<ffffffff810a5acf>] kthread+0xcf/0xe0
[<ffffffff810b41b3>] ? finish_task_switch+0x53/0x170
[<ffffffff810a5a00>] ? kthread_create_on_node+0x140/0x140
[<ffffffff81645dd8>] ret_from_fork+0x58/0x90
[<ffffffff810a5a00>] ? kthread_create_on_node+0x140/0x140
RIP [<ffffffffa050828a>] rbd_dev_refresh+0xfa/0x180 [rbd]
If an error occurs during rbd map, we have to error out, potentially
tearing down a watch. Just like on rbd unmap, notifies have to be
flushed, otherwise rbd_watch_cb() may end up trying to read in the
image header after rbd_dev_image_release() has run:
Assertion failure in rbd_dev_header_info() at line 4722:
rbd_assert(rbd_image_format_valid(rbd_dev->image_format));
Call Trace:
[<ffffffff81cccee0>] ? rbd_parent_request_create+0x150/0x150
[<ffffffff81cd4e59>] rbd_dev_refresh+0x59/0x390
[<ffffffff81cd5229>] rbd_watch_cb+0x69/0x290
[<ffffffff81fde9bf>] do_event_work+0x10f/0x1c0
[<ffffffff81107799>] process_one_work+0x689/0x1a80
[<ffffffff811076f7>] ? process_one_work+0x5e7/0x1a80
[<ffffffff81132065>] ? finish_task_switch+0x225/0x640
[<ffffffff81107110>] ? pwq_dec_nr_in_flight+0x2b0/0x2b0
[<ffffffff81108c69>] worker_thread+0xd9/0x1320
[<ffffffff81108b90>] ? process_one_work+0x1a80/0x1a80
[<ffffffff8111b02d>] kthread+0x21d/0x2e0
[<ffffffff8111ae10>] ? kthread_stop+0x550/0x550
[<ffffffff82022802>] ret_from_fork+0x22/0x40
[<ffffffff8111ae10>] ? kthread_stop+0x550/0x550
RIP [<ffffffff81ccd8f9>] rbd_dev_header_info+0xa19/0x1e30
To fix this, a) check if RBD_DEV_FLAG_EXISTS is set before calling
revalidate_disk(), b) move ceph_osdc_flush_notifies() call into
rbd_dev_header_unwatch_sync() to cover rbd map error paths and c) turn
header read-in into a critical section. The latter also happens to
take care of rbd map foo@bar vs rbd snap rm foo@bar race.
Fixes: http://tracker.ceph.com/issues/15490
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Simply creating a file system on an skd device, followed by mount and
fstrim will result in errors in the logs and then a BUG(). Let's remove
discard support from that driver. As far as I can tell, it hasn't
worked right since it was merged. This patch also has a side-effect of
cleaning up an unintentional shadowed declaration inside of
skd_end_request.
I tested to ensure that I can still do I/O to the device using xfstests
./check -g quick. I didn't do anything more extensive than that,
though.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block fixes from Jens Axboe:
"A few fixes for the current series. This contains:
- Two fixes for NVMe:
One fixes a reset race that can be triggered by repeated
insert/removal of the module.
The other fixes an issue on some platforms, where we get probe
timeouts since legacy interrupts isn't working. This used not to
be a problem since we had the worker thread poll for completions,
but since that was killed off, it means those poor souls can't
successfully probe their NVMe device. Use a proper IRQ check and
probe (msi-x -> msi ->legacy), like most other drivers to work
around this. Both from Keith.
- A loop corruption issue with offset in iters, from Ming Lei.
- A fix for not having the partition stat per cpu ref count
initialized before sending out the KOBJ_ADD, which could cause user
space to access the counter prior to initialization. Also from
Ming Lei.
- A fix for using the wrong congestion state, from Kaixu Xia"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: loop: fix filesystem corruption in case of aio/dio
NVMe: Always use MSI/MSI-x interrupts
NVMe: Fix reset/remove race
writeback: fix the wrong congested state variable definition
block: partition: initialize percpuref before sending out KOBJ_ADD
Starting from commit e36f620428(block: split bios to max possible length),
block core starts to split bio in the middle of bvec.
Unfortunately loop dio/aio doesn't consider this situation, and
always treat 'iter.iov_offset' as zero. Then filesystem corruption
is observed.
This patch figures out the offset of the base bvevc via
'bio->bi_iter.bi_bvec_done' and fixes the issue by passing the offset
to iov iterator.
Fixes: e36f620428 (block: split bios to max possible length)
Cc: Keith Busch <keith.busch@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org (4.5)
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we converted everything to the newer block write cache
interface, kill off the queue flush_flags and queueable flush
entries.
Signed-off-by: Jens Axboe <axboe@fb.com>
The driver calls it with 0 for flags, since it doesn't have a writeback
cache. Just remove the call, as it's a no-op right now.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Only a single tags array anyway.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
We could kmalloc() the payload, so need the offset in page.
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull Ceph fix from Sage Weil:
"This just fixes a few remaining memory allocations in RBD to use
GFP_NOIO instead of GFP_ATOMIC"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use GFP_NOIO consistently for request allocations
As of 5a60e87603, RBD object request
allocations are made via rbd_obj_request_create() with GFP_NOIO.
However, subsequent OSD request allocations in rbd_osd_req_create*()
use GFP_ATOMIC.
With heavy page cache usage (e.g. OSDs running on same host as krbd
client), rbd_osd_req_create() order-1 GFP_ATOMIC allocations have been
observed to fail, where direct reclaim would have allowed GFP_NOIO
allocations to succeed.
Cc: stable@vger.kernel.org # 3.18+
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Suggested-by: Neil Brown <neilb@suse.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Mostly direct substitution with occasional adjustment or removing
outdated comments.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull Ceph updates from Sage Weil:
"There is quite a bit here, including some overdue refactoring and
cleanup on the mon_client and osd_client code from Ilya, scattered
writeback support for CephFS and a pile of bug fixes from Zheng, and a
few random cleanups and fixes from others"
[ I already decided not to pull this because of it having been rebased
recently, but ended up changing my mind after all. Next time I'll
really hold people to it. Oh well. - Linus ]
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (34 commits)
libceph: use KMEM_CACHE macro
ceph: use kmem_cache_zalloc
rbd: use KMEM_CACHE macro
ceph: use lookup request to revalidate dentry
ceph: kill ceph_get_dentry_parent_inode()
ceph: fix security xattr deadlock
ceph: don't request vxattrs from MDS
ceph: fix mounting same fs multiple times
ceph: remove unnecessary NULL check
ceph: avoid updating directory inode's i_size accidentally
ceph: fix race during filling readdir cache
libceph: use sizeof_footer() more
ceph: kill ceph_empty_snapc
ceph: fix a wrong comparison
ceph: replace CURRENT_TIME by current_fs_time()
ceph: scattered page writeback
libceph: add helper that duplicates last extent operation
libceph: enable large, variable-sized OSD requests
libceph: osdc->req_mempool should be backed by a slab pool
libceph: make r_request msg_size calculation clearer
...
Use KMEM_CACHE() instead of kmem_cache_create() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Turn r_ops into a flexible array member to enable large, consisting of
up to 16 ops, OSD requests. The use case is scattered writeback in
cephfs and, as far as the kernel client is concerned, 16 is just a made
up number.
r_ops had size 3 for copyup+hint+write, but copyup is really a special
case - it can only happen once. ceph_osd_request_cache is therefore
stuffed with num_ops=2 requests, anything bigger than that is allocated
with kmalloc(). req_mempool is backed by ceph_osd_request_cache, which
means either num_ops=1 or num_ops=2 for use_mempool=true - all existing
users (ceph_writepages_start(), ceph_osdc_writepages()) are fine with
that.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
This avoids defining large array of r_reply_op_{len,result} in
in struct ceph_osd_request.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Pull block fixes from Jens Axboe:
"Final round of fixes for this merge window - some of this has come up
after the initial pull request, and some of it was put in a post-merge
branch before the merge window.
This contains:
- Fix for a bad check for an error on dma mapping in the mtip32xx
driver, from Alexey Khoroshilov.
- A set of fixes for lightnvm, from Javier, Matias, and Wenwei.
- An NVMe completion record corruption fix from Marta, ensuring that
we read things in the right order.
- Two writeback fixes from Tejun, marked for stable@ as well.
- A blk-mq sw queue iterator fix from Thomas, fixing an oops for
sparse CPU maps. They hit this in the hot plug/unplug rework"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: avoid cqe corruption when update at the same time as read
writeback, cgroup: fix use of the wrong bdi_writeback which mismatches the inode
writeback, cgroup: fix premature wb_put() in locked_inode_to_wb_and_lock_list()
blk-mq: Use proper cpumask iterator
mtip32xx: fix checks for dma mapping errors
lightnvm: do not load L2P table if not supported
lightnvm: do not reserve lun on l2p loading
nvme: lightnvm: return ppa completion status
lightnvm: add a bitmap of luns
lightnvm: specify target's logical address area
null_blk: add lightnvm null_blk device to the nullb_list
This adds basic polling support for vhost.
Reworks virtio to optionally use DMA API, fixing it on Xen.
Balloon stats gained a new entry.
Using the new napi_alloc_skb speeds up virtio net.
virtio blk stats can now be read while another VCPU
us busy inflating or deflating the balloon.
Plus misc cleanups in various places.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW7qRJAAoJECgfDbjSjVRpVNoH/A7z+lZ6nooSJ9fUBtAAlwit
mE1VKi8g0G6naV1NVLFVe7hPAejExGiHfR3ZUrVoenJKj2yeW/DFojFC10YR/KTe
ac7Imuc+owA3UOE/QpeGBs59+EEWKTZUYt6r8HSJVwoodeosw9v2ecP/Iwhbax8H
a4V3HqOADjKnHg73R9o3u+bAgA1GrGYHeK0AfhCBSTNwlPdxkvf0463HgfOpM4nl
/sNoFWO3vOyekk+loIk+jpmWVIoIfG2NFzW4lPwEPkfqUBX7r0ei/NR23hIqHL7r
QZ6vMj1Ew9qctUONbJu4kXjuV2Vk9NhxwbDjoJtm8plKL2hz2prJynUEogkHh2g=
=VMD0
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost updates from Michael Tsirkin:
"New features, performance improvements, cleanups:
- basic polling support for vhost
- rework virtio to optionally use DMA API, fixing it on Xen
- balloon stats gained a new entry
- using the new napi_alloc_skb speeds up virtio net
- virtio blk stats can now be read while another VCPU is busy
inflating or deflating the balloon
plus misc cleanups in various places"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_net: replace netdev_alloc_skb_ip_align() with napi_alloc_skb()
vhost_net: basic polling support
vhost: introduce vhost_vq_avail_empty()
vhost: introduce vhost_has_work()
virtio_balloon: Allow to resize and update the balloon stats in parallel
virtio_balloon: Use a workqueue instead of "vballoon" kthread
virtio/s390: size of SET_IND payload
virtio/s390: use dev_to_virtio
vhost: rename vhost_init_used()
vhost: rename cross-endian helpers
virtio_blk: VIRTIO_BLK_F_WCE->VIRTIO_BLK_F_FLUSH
vring: Use the DMA API on Xen
virtio_pci: Use the DMA API if enabled
virtio_mmio: Use the DMA API if enabled
virtio: Add improved queue allocation API
virtio_ring: Support DMA APIs
vring: Introduce vring_use_dma_api()
s390/dma: Allow per device dma ops
alpha/dma: use common noop dma ops
dma: Provide simple noop dma ops
Merge second patch-bomb from Andrew Morton:
- a couple of hotfixes
- the rest of MM
- a new timer slack control in procfs
- a couple of procfs fixes
- a few misc things
- some printk tweaks
- lib/ updates, notably to radix-tree.
- add my and Nick Piggin's old userspace radix-tree test harness to
tools/testing/radix-tree/. Matthew said it was a godsend during the
radix-tree work he did.
- a few code-size improvements, switching to __always_inline where gcc
screwed up.
- partially implement character sets in sscanf
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
sscanf: implement basic character sets
lib/bug.c: use common WARN helper
param: convert some "on"/"off" users to strtobool
lib: add "on"/"off" support to kstrtobool
lib: update single-char callers of strtobool()
lib: move strtobool() to kstrtobool()
include/linux/unaligned: force inlining of byteswap operations
include/uapi/linux/byteorder, swab: force inlining of some byteswap operations
include/asm-generic/atomic-long.h: force inlining of some atomic_long operations
usb: common: convert to use match_string() helper
ide: hpt366: convert to use match_string() helper
ata: hpt366: convert to use match_string() helper
power: ab8500: convert to use match_string() helper
power: charger_manager: convert to use match_string() helper
drm/edid: convert to use match_string() helper
pinctrl: convert to use match_string() helper
device property: convert to use match_string() helper
lib/string: introduce match_string() helper
radix-tree tests: add test for radix_tree_iter_next
radix-tree tests: add regression3 test
...
exec_drive_taskfile() checks for dma mapping errors by comparison
returned address with zero, while pci_dma_mapping_error() should be used.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Jens Axboe <axboe@fb.com>
After register null_blk devices into lightnvm, we forget
to add these devices to the the nullb_list, makes them
invisible to the null_blk driver.
Signed-off-by: Wenwei Tao <ww.tao0320@gmail.com>
Fixes: a514379b0c ("null_blk: oops when initializing without lightnvm")
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block driver updates from Jens Axboe:
"This is the block driver pull request for this merge window. It sits
on top of for-4.6/core, that was just sent out.
This contains:
- A set of fixes for lightnvm. One from Alan, fixing an overflow,
and the rest from the usual suspects, Javier and Matias.
- A set of fixes for nbd from Markus and Dan, and a fixup from Arnd
for correct usage of the signed 64-bit divider.
- A set of bug fixes for the Micron mtip32xx, from Asai.
- A fix for the brd discard handling from Bart.
- Update the maintainers entry for cciss, since that hardware has
transferred ownership.
- Three bug fixes for bcache from Eric Wheeler.
- Set of fixes for xen-blk{back,front} from Jan and Konrad.
- Removal of the cpqarray driver. It has been disabled in Kconfig
since 2013, and we were initially scheduled to remove it in 3.15.
- Various updates and fixes for NVMe, with the most important being:
- Removal of the per-device NVMe thread, replacing that with a
watchdog timer instead. From Christoph.
- Exposing the namespace WWID through sysfs, from Keith.
- Set of cleanups from Ming Lin.
- Logging the controller device name instead of the underlying
PCI device name, from Sagi.
- And a bunch of fixes and optimizations from the usual suspects
in this area"
* 'for-4.6/drivers' of git://git.kernel.dk/linux-block: (49 commits)
NVMe: Expose ns wwid through single sysfs entry
drivers:block: cpqarray clean up
brd: Fix discard request processing
cpqarray: remove it from the kernel
cciss: update MAINTAINERS
NVMe: Remove unused sq_head read in completion path
bcache: fix cache_set_flush() NULL pointer dereference on OOM
bcache: cleaned up error handling around register_cache()
bcache: fix race of writeback thread starting before complete initialization
NVMe: Create discard zero quirk white list
nbd: use correct div_s64 helper
mtip32xx: remove unneeded variable in mtip_cmd_timeout()
lightnvm: generalize rrpc ppa calculations
lightnvm: remove struct nvm_dev->total_blocks
lightnvm: rename ->nr_pages to ->nr_sects
lightnvm: update closed list outside of intr context
xen/blback: Fit the important information of the thread in 17 characters
lightnvm: fold get bb tbl when using dual/quad plane mode
lightnvm: fix up nonsensical configure overrun checking
xen-blkback: advertise indirect segment support earlier
...
The success of CMA allocation largely depends on the success of
migration and key factor of it is page reference count. Until now, page
reference is manipulated by direct calling atomic functions so we cannot
follow up who and where manipulate it. Then, it is hard to find actual
reason of CMA allocation failure. CMA allocation should be guaranteed
to succeed so finding offending place is really important.
In this patch, call sites where page reference is manipulated are
converted to introduced wrapper function. This is preparation step to
add tracepoint to each page reference manipulation function. With this
facility, we can easily find reason of CMA allocation failure. There is
no functional change in this patch.
In addition, this patch also converts reference read sites. It will
help a second step that renames page._count to something else and
prevents later attempt to direct access to it (Suggested by Andrew).
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.6:
API:
- Convert remaining crypto_hash users to shash or ahash, also convert
blkcipher/ablkcipher users to skcipher.
- Remove crypto_hash interface.
- Remove crypto_pcomp interface.
- Add crypto engine for async cipher drivers.
- Add akcipher documentation.
- Add skcipher documentation.
Algorithms:
- Rename crypto/crc32 to avoid name clash with lib/crc32.
- Fix bug in keywrap where we zero the wrong pointer.
Drivers:
- Support T5/M5, T7/M7 SPARC CPUs in n2 hwrng driver.
- Add PIC32 hwrng driver.
- Support BCM6368 in bcm63xx hwrng driver.
- Pack structs for 32-bit compat users in qat.
- Use crypto engine in omap-aes.
- Add support for sama5d2x SoCs in atmel-sha.
- Make atmel-sha available again.
- Make sahara hashing available again.
- Make ccp hashing available again.
- Make sha1-mb available again.
- Add support for multiple devices in ccp.
- Improve DMA performance in caam.
- Add hashing support to rockchip"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (116 commits)
crypto: qat - remove redundant arbiter configuration
crypto: ux500 - fix checks of error code returned by devm_ioremap_resource()
crypto: atmel - fix checks of error code returned by devm_ioremap_resource()
crypto: qat - Change the definition of icp_qat_uof_regtype
hwrng: exynos - use __maybe_unused to hide pm functions
crypto: ccp - Add abstraction for device-specific calls
crypto: ccp - CCP versioning support
crypto: ccp - Support for multiple CCPs
crypto: ccp - Remove check for x86 family and model
crypto: ccp - memset request context to zero during import
lib/mpi: use "static inline" instead of "extern inline"
lib/mpi: avoid assembler warning
hwrng: bcm63xx - fix non device tree compatibility
crypto: testmgr - allow rfc3686 aes-ctr variants in fips mode.
crypto: qat - The AE id should be less than the maximal AE number
lib/mpi: Endianness fix
crypto: rockchip - add hash support for crypto engine in rk3288
crypto: xts - fix compile errors
crypto: doc - add skcipher API documentation
crypto: doc - update AEAD AD handling
...
gcc-6.0 found an ancient bug in the paride driver, which had a
"module_param(verbose, bool, 0);" since before 2.6.12, but actually uses
it to accept '0', '1' or '2' as arguments:
drivers/block/paride/pd.c: In function 'pd_init_dev_parms':
drivers/block/paride/pd.c:298:29: warning: comparison of constant '1' with boolean expression is always false [-Wbool-compare]
#define DBMSG(msg) ((verbose>1)?(msg):NULL)
In 2012, Rusty did a cleanup patch that also changed the type of the
variable to 'bool', which introduced what is now a gcc warning.
This changes the type back to 'int' and adapts the module_param() line
instead, so it should work as documented in case anyone ever cares about
running the ancient driver with debugging.
Fixes: 90ab5ee941 ("module_param: make bool parameters really bool (drivers & misc)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rusty Russell <rusty@rustcorp.com.au>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit d436641439 ("cpqarray: remove it from the kernel") removes the
Kconfig option BLK_CPQ_DA and cpqarray.
Remove the dead build rule in the Makefile.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Avoid that discard requests with size => PAGE_SIZE fail with
-EIO. Refuse discard requests if the discard size is not a
multiple of the page size.
Fixes: 2dbe549576 ("brd: Refuse improperly aligned discard requests")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Jan Kara <jack@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robert Elliot <elliott@hp.com>
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Jens Axboe <axboe@fb.com>
We disabled the ability to enable this driver back in October of 2013,
we should be able to safely remove it at this point. The initial goal
was to remove it in 3.15, so now is the time.
Signed-off-by: Jens Axboe <axboe@fb.com>
The do_div() macro now checks its arguments for the correct type,
and refuses anything other than u64, so we get a warning about
nbd_ioctl passing in an loff_t:
drivers/block/nbd.c: In function '__nbd_ioctl':
drivers/block/nbd.c:757:77: error: comparison of distinct pointer types lacks a cast [-Werror]
This changes the nbd code to use div_s64() instead, which takes
a signed argument.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 37091fdd83 ("nbd: Create size change events for userspace")
Signed-off-by: Jens Axboe <axboe@fb.com>
The processes names are truncated to 17, while we had the length
of the process as name 20 - which meant that while we filled
it out with various details - the last 3 characters (which had
the queue number) never surfaced to the user-space.
To simplify this and be able to fit the device name, domain id,
and the queue number we remove the 'blkback' from the name.
Prior to this patch the device name is "blkback.<domid>.<name>"
for example: blkback.8.xvda, blkback.11.hda.
With the multiqueue block backend we add "-%d" for the queue.
But sadly this is already way past the limit so it gets stripped.
Possible solution had been identified by Ian:
http://lists.xenproject.org/archives/html/xen-devel/2015-05/msg03516.html
"
If you are pressed for space then the "xvd" is probably a bit redundant
in a string which starts blkbk.
The guest may not even call the device xvdN (iirc BSD has another
prefix) any how, so having blkback say so seems of limited use anyway.
Since this seems to not include a partition number how does this work in
the split partition scheme? (i.e. one where the guest is given xvda1 and
xvda2 rather than xvda with a partition table)
[It will be 'blkback.8.xvda1', and 'blkback.11.xvda2']
Perhaps something derived from one of the schemes in
http://xenbits.xen.org/docs/unstable/misc/vbd-interface.txt might be a
better fit?
After a bit of discussion (see
http://lists.xenproject.org/archives/html/xen-devel/2015-12/msg01588.html)
we settled on dropping the "blback" part.
This will make it possible to have the <domid>.<name>-<queue>:
[1.xvda-0]
[1.xvda-1]
And we enough space to make it go up to:
[32100.xvdfg9-5]
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
There's no reason to defer this until the connect phase, and in fact
there are frontend implementations expecting this to be available
earlier. Move it into the probe function.
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
"max" is rather ambiguous and carries pretty little meaning, the more
that there are also "max_queues" and "max_ring_page_order". Make this
"max_indirect_segments" instead, and at once change the type from int
to uint (to match the respective variable's type).
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Fail all pending requests after surprise removal of a drive.
Signed-off-by: Vignesh Gunasekaran <vgunasekaran@micron.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Allow device initialization to finish gracefully when it is in
FTL rebuild failure state. Also, recover device out of this state
after successfully secure erasing it.
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Vignesh Gunasekaran <vgunasekaran@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Flush inflight IOs using fsync_bdev() when the device is safely
removed. Also, block further IOs in device open function.
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Rajesh Kumar Sambandam <rsambandam@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
When FTL rebuild is in progress, alloc_disk() initializes the disk
but device node will be created by add_disk() only after successful
completion of FTL rebuild. So, skip deletion of device node in
removal path when FTL rebuild is in progress.
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Prevent standby immediate command from being issued in remove,
suspend and shutdown paths, while drive is in FTL rebuild process.
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Vignesh Gunasekaran <vgunasekaran@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Print exact time when an internal command is interrupted.
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Rajesh Kumar Sambandam <rsambandam@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Remove setting and clearing MTIP_PF_EH_ACTIVE_BIT flag in
mtip_handle_tfe() as they are redundant. Also avoid waking
up service thread from mtip_handle_tfe() because it is
already woken up in case of taskfile error.
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Rajesh Kumar Sambandam <rsambandam@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Service thread does not detect the need for taskfile error hanlding. Fixed the
flag condition to process taskfile error.
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Latest virtio spec says the feature bit name is VIRTIO_BLK_F_FLUSH,
VIRTIO_BLK_F_WCE is the legacy name. virtio blk header says exactly the
reverse - fix that and update driver code to match.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The userspace needs to know when nbd devices are ready for use.
Currently no events are created for the userspace which doesn't work for
systemd.
See the discussion here: https://github.com/systemd/systemd/pull/358
This patch uses a central point to setup the nbd-internal sizes. A ioctl
to set a size does not lead to a visible size change. The size of the
block device will be kept at 0 until nbd is connected. As soon as it
connects, the size will be changed to the real value and a uevent is
created. When disconnecting, the blockdevice is set to 0 size and
another uevent is generated.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
If the LightNVM subsystem is not compiled into the kernel, and the
null_blk device driver requests lightnvm to be initialized. The call to
nvm_register fails and the null_add_dev function cleans up the
initialization. However, at this point the null block device has
already been added to the nullb_list and thus a second cleanup will
occur when the function has returned, that leads to a double call to
blk_cleanup_queue.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
In case /dev/fdX is open with O_NDELAY / O_NONBLOCK, floppy_open() immediately
succeeds, without performing any further media / controller preparations.
That's "correct" wrt. the NODELAY flag, but is hardly correct wrt. the rest
of the floppy driver, that is not really O_NONBLOCK ready, at all. Therefore
it's not too surprising, that subsequent attempts to work with the
filedescriptor produce bad results. Namely, syzkaller tool has been able
to livelock mmap() on the returned fd to keep waiting on the page unlock
bit forever.
Quite frankly, I have trouble defining what non-blocking behavior would be for
floppies. Is waiting ages for the driver to actually succeed reading a sector
blocking operation? Is waiting for drive motor to start blocking operation? How
about in case of virtualized floppies?
One option would be returning EWOULDBLOCK in case O_NDLEAY / O_NONBLOCK is
being passed to open(). That has a theoretical potential of breaking some
arcane and archaic userspace though.
Let's take a more conservative aproach, and accept the O_NDLEAY flag, and let
the driver behave as usual.
While at it, clean up a bit handling of !(mode & (FMODE_READ|FMODE_WRITE))
case and return EINVAL instead of succeeding as well.
Spotted by syzkaller tool.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make the "Attempted send on closed socket" error messages generated in
nbd_request_handler() ratelimited.
When the nbd socket is shutdown, the nbd_request_handler() function emits
an error message for every request remaining in its queue. If the queue
is large, this will spam a large amount of messages to the log. There's
no need for a separate error message for each request, so this patch
ratelimits it.
In the specific case this was found, the system was virtual and the error
messages were logged to the serial port, which overwhelmed it.
Fixes: 4d48a542b4 ("nbd: fix I/O hang on disconnected nbds")
Signed-off-by: Dan Streetman <dan.streetman@canonical.com>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
nbd changes properties of the blockdevice depending on flags that were
received. This patch moves this flag parsing into a separate function
nbd_parse_flags().
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Group all variables that are reset after a disconnect into reset
functions. This patch adds two of these functions, nbd_reset() and
nbd_bdev_reset().
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
It may be useful to know in the client that a connection timed out. The
current code returns success for a timeout.
This patch reports the error code -ETIMEDOUT for a timeout.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
As discussed on the mailing list, the usage of signals for timeout
handling has a lot of potential issues. The nbd driver used for some
time signals for timeouts. These signals where able to get the threads
out of the blocking socket operations.
This patch removes all signal usage and uses a socket shutdown instead.
The socket descriptor itself is cleared later when the whole nbd device
is closed.
The tasks_lock is removed as we do not depend on this anymore. Instead
a new lock for the socket is introduced so we can safely work with the
socket in the timeout handler outside of the two main threads.
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
System block allows the device to initialize with its configured media
manager. The system blocks is written to disk, and read again when media
manager is determined. For this to work, the backend must store the
data. Device drivers, such as null_blk, does not have any backend
storage. This patch allows the media manager to be initialized without a
storage backend.
It also fix incorrect configuration of capabilities in null_blk, as it
does not support get/set bad block interface.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Static checker complains about the implemented error handling. It is
indeed wrong. We don't care about the return values of created debugfs
files.
We only have to check the return values of created dirs for NULL
pointer. If we use a null pointer as parent directory for files, this
may lead to debugfs files in wrong places.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
floppy_revalidate() doesn't perform any error handling on lock_fdc()
result. lock_fdc() might actually be interrupted by a signal (it waits for
fdc becoming non-busy interruptibly). In such case, floppy_revalidate()
proceeds as if it had claimed the lock, but it fact it doesn't.
In case of multiple threads trying to open("/dev/fdX"), this leads to
serious corruptions all over the place, because all of a sudden there is
no critical section protection (that'd otherwise be guaranteed by locked
fd) whatsoever.
While at this, fix the fact that the 'interruptible' parameter to
lock_fdc() doesn't make any sense whatsoever, because we always wait
interruptibly anyway.
Most of the lock_fdc() callsites do properly handle error (and propagate
EINTR), but floppy_revalidate() and floppy_check_events() don't. Fix this.
Spotted by 'syzkaller' tool.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Need to reallocate ring info in the resume path, because info->rinfo was freed
in blkif_free(). And 'multi-queue-max-queues' backend reports may have been
changed.
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Reported-and-Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This patch replaces uses of the long obsolete hash interface with
either shash (for non-SG users) or ahash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull Ceph updates from Sage Weil:
"The two main changes are aio support in CephFS, and a series that
fixes several issues in the authentication key timeout/renewal code.
On top of that are a variety of cleanups and minor bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: remove outdated comment
libceph: kill off ceph_x_ticket_handler::validity
libceph: invalidate AUTH in addition to a service ticket
libceph: fix authorizer invalidation, take 2
libceph: clear messenger auth_retry flag if we fault
libceph: fix ceph_msg_revoke()
libceph: use list_for_each_entry_safe
ceph: use i_size_{read,write} to get/set i_size
ceph: re-send AIO write request when getting -EOLDSNAP error
ceph: Asynchronous IO support
ceph: Avoid to propagate the invalid page point
ceph: fix double page_unlock() in page_mkwrite()
rbd: delete an unnecessary check before rbd_dev_destroy()
libceph: use list_next_entry instead of list_entry_next
ceph: ceph_frag_contains_value can be boolean
ceph: remove unused functions in ceph_frag.h
Pull final vfs updates from Al Viro:
- The ->i_mutex wrappers (with small prereq in lustre)
- a fix for too early freeing of symlink bodies on shmem (they need to
be RCU-delayed) (-stable fodder)
- followup to dedupe stuff merged this cycle
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: abort dedupe loop if fatal signals are pending
make sure that freeing shmem fast symlinks is RCU-delayed
wrappers for ->i_mutex access
lustre: remove unused declaration
There are many locations that do
if (memory_was_allocated_by_vmalloc)
vfree(ptr);
else
kfree(ptr);
but kvfree() can handle both kmalloc()ed memory and vmalloc()ed memory
using is_vmalloc_addr(). Unless callers have special reasons, we can
replace this branch with kvfree(). Please check and reply if you found
problems.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Jan Kara <jack@suse.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Acked-by: David Rientjes <rientjes@google.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Boris Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
parallel to mutex_{lock,unlock,trylock,is_locked,lock_nested},
inode_foo(inode) being mutex_foo(&inode->i_mutex).
Please, use those for access to ->i_mutex; over the coming cycle
->i_mutex will become rwsem, with ->lookup() done with it held
only shared.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull lightnvm fixes and updates from Jens Axboe:
"This should have been part of the drivers branch, but it arrived a bit
late and wasn't based on the official core block driver branch. So
they got a small scolding, but got a pass since it's still new. Hence
it's in a separate branch.
This is mostly pure fixes, contained to lightnvm/, and minor feature
additions"
* 'for-4.5/lightnvm' of git://git.kernel.dk/linux-block: (26 commits)
lightnvm: ensure that nvm_dev_ops can be used without CONFIG_NVM
lightnvm: introduce factory reset
lightnvm: use system block for mm initialization
lightnvm: introduce ioctl to initialize device
lightnvm: core on-disk initialization
lightnvm: introduce mlc lower page table mappings
lightnvm: add mccap support
lightnvm: manage open and closed blocks separately
lightnvm: fix missing grown bad block type
lightnvm: reference rrpc lun in rrpc block
lightnvm: introduce nvm_submit_ppa
lightnvm: move rq->error to nvm_rq->error
lightnvm: support multiple ppas in nvm_erase_ppa
lightnvm: move the pages per block check out of the loop
lightnvm: sectors first in ppa list
lightnvm: fix locking and mempool in rrpc_lun_gc
lightnvm: put block back to gc list on its reclaim fail
lightnvm: check bi_error in gc
lightnvm: return the get_bb_tbl return value
lightnvm: refactor end_io functions for sync
...
Pull block driver updates from Jens Axboe:
"This is the block driver pull request for 4.5, with the exception of
NVMe, which is in a separate branch and will be posted after this one.
This pull request contains:
- A set of bcache stability fixes, which have been acked by Kent.
These have been used and tested for more than a year by the
community, so it's about time that they got in.
- A set of drbd updates from the drbd team (Andreas, Lars, Philipp)
and Markus Elfring, Oleg Drokin.
- A set of fixes for xen blkback/front from the usual suspects, (Bob,
Konrad) as well as community based fixes from Kiri, Julien, and
Peng.
- A 2038 time fix for sx8 from Shraddha, with a fix from me.
- A small mtip32xx cleanup from Zhu Yanjun.
- A null_blk division fix from Arnd"
* 'for-4.5/drivers' of git://git.kernel.dk/linux-block: (71 commits)
null_blk: use sector_div instead of do_div
mtip32xx: restrict variables visible in current code module
xen/blkfront: Fix crash if backend doesn't follow the right states.
xen/blkback: Fix two memory leaks.
xen/blkback: make st_ statistics per ring
xen/blkfront: Handle non-indirect grant with 64KB pages
xen-blkfront: Introduce blkif_ring_get_request
xen-blkback: clear PF_NOFREEZE for xen_blkif_schedule()
xen/blkback: Free resources if connect_ring failed.
xen/blocks: Return -EXX instead of -1
xen/blkback: make pool of persistent grants and free pages per-queue
xen/blkback: get the number of hardware queues/rings from blkfront
xen/blkback: pseudo support for multi hardware queues/rings
xen/blkback: separate ring information out of struct xen_blkif
xen/blkfront: correct setting for xen_blkif_max_ring_order
xen/blkfront: make persistent grants pool per-queue
xen/blkfront: Remove duplicate setting of ->xbdev.
xen/blkfront: Cleanup of comments, fix unaligned variables, and syntax errors.
xen/blkfront: negotiate number of queues/rings to be used with backend
xen/blkfront: split per device io_lock
...
The rbd_dev_destroy() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Pull core block updates from Jens Axboe:
"We don't have a lot of core changes this time around, it's mostly in
drivers, which will come in a subsequent pull.
The cores changes include:
- blk-mq
- Prep patch from Christoph, changing blk_mq_alloc_request() to
take flags instead of just using gfp_t for sleep/nosleep.
- Doc patch from me, clarifying the difference between legacy
and blk-mq for timer usage.
- Fixes from Raghavendra for memory-less numa nodes, and a reuse
of CPU masks.
- Cleanup from Geliang Tang, using offset_in_page() instead of open
coding it.
- From Ilya, rename request_queue slab to it reflects what it holds,
and a fix for proper use of bdgrab/put.
- A real fix for the split across stripe boundaries from Keith. We
yanked a broken version of this from 4.4-rc final, this one works.
- From Mike Krinkin, emit a trace message when we split.
- From Wei Tang, two small cleanups, not explicitly clearing memory
that is already cleared"
* 'for-4.5/core' of git://git.kernel.dk/linux-block:
block: use bd{grab,put}() instead of open-coding
block: split bios to max possible length
block: add call to split trace point
blk-mq: Avoid memoryless numa node encoded in hctx numa_node
blk-mq: Reuse hardware context cpumask for tags
blk-mq: add a flags parameter to blk_mq_alloc_request
Revert "blk-flush: Queue through IO scheduler when flush not required"
block: clarify blk_add_timer() use case for blk-mq
bio: use offset_in_page macro
block: do not initialise statics to 0 or NULL
block: do not initialise globals to 0 or NULL
block: rename request_queue slab cache
For the purpose of communicating the optional presence of a 'struct
page' for the pfn returned from ->direct_access(), introduce a type that
encapsulates a page-frame-number plus flags. These flags contain the
historical "page_link" encoding for a scatterlist entry, but can also
denote "device memory". Where "device memory" is a set of pfns that are
not part of the kernel's linear mapping by default, but are accessed via
the same memory controller as ram.
The motivation for this new type is large capacity persistent memory
that needs struct page entries in the 'memmap' to support 3rd party DMA
(i.e. O_DIRECT I/O with a persistent memory source/target). However,
we also need it in support of maintaining a list of mapped inodes which
need to be unmapped at driver teardown or freeze_bdev() time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Hansen <dave@sr71.net>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The use of idr_remove() is forbidden in the callback functions of
idr_for_each(). It is therefore unsafe to call idr_remove in
zram_remove().
This patch moves the call to idr_remove() from zram_remove() to
hot_remove_store(). In the detroy_devices() path, idrs are removed by
idr_destroy(). This solves an use-after-free detected by KASan.
[akpm@linux-foundation.org: fix coding stype, per Sergey]
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: <stable@vger.kernel.org> [4.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge first patch-bomb from Andrew Morton:
- A few hotfixes which missed 4.4 becasue I was asleep. cc'ed to
-stable
- A few misc fixes
- OCFS2 updates
- Part of MM. Including pretty large changes to page-flags handling
and to thp management which have been buffered up for 2-3 cycles now.
I have a lot of MM material this time.
[ It turns out the THP part wasn't quite ready, so that got dropped from
this series - Linus ]
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (117 commits)
zsmalloc: reorganize struct size_class to pack 4 bytes hole
mm/zbud.c: use list_last_entry() instead of list_tail_entry()
zram/zcomp: do not zero out zcomp private pages
zram: pass gfp from zcomp frontend to backend
zram: try vmalloc() after kmalloc()
zram/zcomp: use GFP_NOIO to allocate streams
mm: add tracepoint for scanning pages
drivers/base/memory.c: fix kernel warning during memory hotplug on ppc64
mm/page_isolation: use macro to judge the alignment
mm: fix noisy sparse warning in LIBCFS_ALLOC_PRE()
mm: rework virtual memory accounting
include/linux/memblock.h: fix ordering of 'flags' argument in comments
mm: move lru_to_page to mm_inline.h
Documentation/filesystems: describe the shared memory usage/accounting
memory-hotplug: don't BUG() in register_memory_resource()
hugetlb: make mm and fs code explicitly non-modular
mm/swapfile.c: use list_for_each_entry_safe in free_swap_count_continuations
mm: /proc/pid/clear_refs: no need to clear VM_SOFTDIRTY in clear_soft_dirty_pmd()
mm: make sure isolate_lru_page() is never called for tail page
vmstat: make vmstat_updater deferrable again and shut down on idle
...
Do not __GFP_ZERO allocated zcomp ->private pages. We keep allocated
streams around and use them for read/write requests, so we supply a
zeroed out ->private to compression algorithm as a scratch buffer only
once -- the first time we use that stream. For the rest of IO requests
served by this stream ->private usually contains some temporarily data
from the previous requests.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Each zcomp backend uses own gfp flag but it's pointless because the
context they could be called is driven by upper layer(ie, zcomp
frontend). As well, zcomp frondend could call them in different
context. One context(ie, zram init part) is it should be better to make
sure successful allocation other context(ie, further stream allocation
part for accelarating I/O speed) is just optional so let's pass gfp down
from driver (ie, zcomp frontend) like normal MM convention.
[sergey.senozhatsky@gmail.com: add missing __vmalloc zero and highmem gfps]
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we're using LZ4 multi compression streams for zram swap, we found
out page allocation failure message in system running test. That was
not only once, but a few(2 - 5 times per test). Also, some failure
cases were continually occurring to try allocation order 3.
In order to make parallel compression private data, we should call
kzalloc() with order 2/3 in runtime(lzo/lz4). But if there is no order
2/3 size memory to allocate in that time, page allocation fails. This
patch makes to use vmalloc() as fallback of kmalloc(), this prevents
page alloc failure warning.
After using this, we never found warning message in running test, also
It could reduce process startup latency about 60-120ms in each case.
For reference a call trace :
Binder_1: page allocation failure: order:3, mode:0x10c0d0
CPU: 0 PID: 424 Comm: Binder_1 Tainted: GW 3.10.49-perf-g991d02b-dirty #20
Call trace:
dump_backtrace+0x0/0x270
show_stack+0x10/0x1c
dump_stack+0x1c/0x28
warn_alloc_failed+0xfc/0x11c
__alloc_pages_nodemask+0x724/0x7f0
__get_free_pages+0x14/0x5c
kmalloc_order_trace+0x38/0xd8
zcomp_lz4_create+0x2c/0x38
zcomp_strm_alloc+0x34/0x78
zcomp_strm_multi_find+0x124/0x1ec
zcomp_strm_find+0xc/0x18
zram_bvec_rw+0x2fc/0x780
zram_make_request+0x25c/0x2d4
generic_make_request+0x80/0xbc
submit_bio+0xa4/0x15c
__swap_writepage+0x218/0x230
swap_writepage+0x3c/0x4c
shrink_page_list+0x51c/0x8d0
shrink_inactive_list+0x3f8/0x60c
shrink_lruvec+0x33c/0x4cc
shrink_zone+0x3c/0x100
try_to_free_pages+0x2b8/0x54c
__alloc_pages_nodemask+0x514/0x7f0
__get_free_pages+0x14/0x5c
proc_info_read+0x50/0xe4
vfs_read+0xa0/0x12c
SyS_read+0x44/0x74
DMA: 3397*4kB (MC) 26*8kB (RC) 0*16kB 0*32kB 0*64kB 0*128kB 0*256kB
0*512kB 0*1024kB 0*2048kB 0*4096kB = 13796kB
[minchan@kernel.org: change vmalloc gfp and adding comment about gfp]
[sergey.senozhatsky@gmail.com: tweak comments and styles]
Signed-off-by: Kyeongdon Kim <kyeongdon.kim@lge.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can end up allocating a new compression stream with GFP_KERNEL from
within the IO path, which may result is nested (recursive) IO
operations. That can introduce problems if the IO path in question is a
reclaimer, holding some locks that will deadlock nested IOs.
Allocate streams and working memory using GFP_NOIO flag, forbidding
recursive IO and FS operations.
An example:
inconsistent {IN-RECLAIM_FS-W} -> {RECLAIM_FS-ON-W} usage.
git/20158 [HC0[0]:SC0[0]:HE1:SE1] takes:
(jbd2_handle){+.+.?.}, at: start_this_handle+0x4ca/0x555
{IN-RECLAIM_FS-W} state was registered at:
__lock_acquire+0x8da/0x117b
lock_acquire+0x10c/0x1a7
start_this_handle+0x52d/0x555
jbd2__journal_start+0xb4/0x237
__ext4_journal_start_sb+0x108/0x17e
ext4_dirty_inode+0x32/0x61
__mark_inode_dirty+0x16b/0x60c
iput+0x11e/0x274
__dentry_kill+0x148/0x1b8
shrink_dentry_list+0x274/0x44a
prune_dcache_sb+0x4a/0x55
super_cache_scan+0xfc/0x176
shrink_slab.part.14.constprop.25+0x2a2/0x4d3
shrink_zone+0x74/0x140
kswapd+0x6b7/0x930
kthread+0x107/0x10f
ret_from_fork+0x3f/0x70
irq event stamp: 138297
hardirqs last enabled at (138297): debug_check_no_locks_freed+0x113/0x12f
hardirqs last disabled at (138296): debug_check_no_locks_freed+0x33/0x12f
softirqs last enabled at (137818): __do_softirq+0x2d3/0x3e9
softirqs last disabled at (137813): irq_exit+0x41/0x95
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(jbd2_handle);
<Interrupt>
lock(jbd2_handle);
*** DEADLOCK ***
5 locks held by git/20158:
#0: (sb_writers#7){.+.+.+}, at: [<ffffffff81155411>] mnt_want_write+0x24/0x4b
#1: (&type->i_mutex_dir_key#2/1){+.+.+.}, at: [<ffffffff81145087>] lock_rename+0xd9/0xe3
#2: (&sb->s_type->i_mutex_key#11){+.+.+.}, at: [<ffffffff8114f8e2>] lock_two_nondirectories+0x3f/0x6b
#3: (&sb->s_type->i_mutex_key#11/4){+.+.+.}, at: [<ffffffff8114f909>] lock_two_nondirectories+0x66/0x6b
#4: (jbd2_handle){+.+.?.}, at: [<ffffffff811e31db>] start_this_handle+0x4ca/0x555
stack backtrace:
CPU: 2 PID: 20158 Comm: git Not tainted 4.1.0-rc7-next-20150615-dbg-00016-g8bdf555-dirty #211
Call Trace:
dump_stack+0x4c/0x6e
mark_lock+0x384/0x56d
mark_held_locks+0x5f/0x76
lockdep_trace_alloc+0xb2/0xb5
kmem_cache_alloc_trace+0x32/0x1e2
zcomp_strm_alloc+0x25/0x73 [zram]
zcomp_strm_multi_find+0xe7/0x173 [zram]
zcomp_strm_find+0xc/0xe [zram]
zram_bvec_rw+0x2ca/0x7e0 [zram]
zram_make_request+0x1fa/0x301 [zram]
generic_make_request+0x9c/0xdb
submit_bio+0xf7/0x120
ext4_io_submit+0x2e/0x43
ext4_bio_write_page+0x1b7/0x300
mpage_submit_page+0x60/0x77
mpage_map_and_submit_buffers+0x10f/0x21d
ext4_writepages+0xc8c/0xe1b
do_writepages+0x23/0x2c
__filemap_fdatawrite_range+0x84/0x8b
filemap_flush+0x1c/0x1e
ext4_alloc_da_blocks+0xb8/0x117
ext4_rename+0x132/0x6dc
? mark_held_locks+0x5f/0x76
ext4_rename2+0x29/0x2b
vfs_rename+0x540/0x636
SyS_renameat2+0x359/0x44d
SyS_rename+0x1e/0x20
entry_SYSCALL_64_fastpath+0x12/0x6f
[minchan@kernel.org: add stable mark]
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Kyeongdon Kim <kyeongdon.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
floppy: make local variable non-static
exynos: fixes an incorrect header guard
dt-bindings: fixes some incorrect header guards
cpufreq-dt: correct dead link in documentation
cpufreq: ARM big LITTLE: correct dead link in documentation
treewide: Fix typos in printk
Documentation: filesystem: Fix typo in fs/eventfd.c
fs/super.c: use && instead of & for warn_on condition
Documentation: fix sysfs-ptp
lib: scatterlist: fix Kconfig description
This pull includes driver updates from the usual suspects (bfa, arcmsr,
scsi_dh_alua, lpfc, storvsc, cxlflash). The major change is the addition of
the hisi_sas driver, which is an ARM platform device for SAS. The other
change of note is an enormous style transformation to the atp870u driver
(which is our worst written SCSI driver).
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJWluqqAAoJEDeqqVYsXL0McuwH/1oqvFOagsvoDcwDyNAUR/eW
VAH454ndIJ0eSXORNfA7ko3ZQKa53x1WN9eKr+RHI7lpGCjwBz2MjnvQsnKISvXp
K0owkJTcAAF+Wdq7rdNlm1VlQHuLvG8TMTnno+NY3CtxCR2yiRWlctkNkjr0rWUv
leXJkXZSThkkiY/rEDZZXee8Ajwac87QT+ELEqCT2HueGZD+J8s59JpsOtZdt6Bj
n94ydOuct8hF3Xt3pdu1oDRpWpoJIyjHtYhdrvzSiKKBHTWtuq1oN0Cwnp0qtEDD
X3K1Mr0yBmAjTOsK+y+bZnJ1y7qJLLt5ZHmVixkzFWujXPNbrIsyYkV5eI432XA=
=ggNi
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This includes driver updates from the usual suspects (bfa, arcmsr,
scsi_dh_alua, lpfc, storvsc, cxlflash).
The major change is the addition of the hisi_sas driver, which is an
ARM platform device for SAS. The other change of note is an enormous
style transformation to the atp870u driver (which is our worst written
SCSI driver)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (169 commits)
cxlflash: Enable device id for future IBM CXL adapter
cxlflash: Resolve oops in wait_port_offline
cxlflash: Fix to resolve cmd leak after host reset
cxlflash: Removed driver date print
cxlflash: Fix to avoid virtual LUN failover failure
cxlflash: Fix to escalate LINK_RESET also on port 1
storvsc: Tighten up the interrupt path
storvsc: Refactor the code in storvsc_channel_init()
storvsc: Properly support Fibre Channel devices
storvsc: Fix a bug in the layout of the hv_fc_wwn_packet
mvsas: Add SGPIO support to Marvell 94xx
mpt3sas: A correction in unmap_resources
hpsa: Add box and bay information for enclosure devices
hpsa: Change SAS transport devices to bus 0.
hpsa: fix path_info_show
cciss: print max outstanding commands as a hex value
scsi_debug: Increase the reported optimal transfer length
lpfc: Update version to 11.0.0.10 for upstream patch set
lpfc: Use kzalloc instead of kmalloc
lpfc: Delete unnecessary checks before the function call "mempool_destroy"
...
Dividing a sector_t number should be done using sector_div rather than do_div
to optimize the 32-bit sector_t case, and with the latest do_div optimizations,
we now get a compile-time warning for this:
arch/arm/include/asm/div64.h:32:95: note: expected 'uint64_t * {aka long long unsigned int *}' but argument is of type 'sector_t * {aka long unsigned int *}'
drivers/block/null_blk.c:521:81: warning: comparison of distinct pointer types lacks a cast
This changes the newly added code to use sector_div. It is a simplified version
of the original patch, as Linus Torvalds pointed out that we should not be using
an expensive division function in the first place.
This version was suggested by Matias Bjorling.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Matias Bjorling <m@bjorling.me>
Fixes: b2b7e00148 ("null_blk: register as a LightNVM device")
Signed-off-by: Jens Axboe <axboe@fb.com>
Konrad writes:
The pull is based on converting the backend driver into an multiqueue
driver and exposing more than one queue to the frontend. As such we had
to modify the frontend and also fix a bunch of bugs around this.
The original work is based on Arianna Avanzini's work as an OPW intern.
Bob took over the work and had been massaging it for quite some time.
Also included are are features to 64KB page support for ARM and various
bug-fixes.
To implement sync I/O support within the LightNVM core, the end_io
functions are refactored to take an end_io function pointer instead of
testing for initialized media manager, followed by calling its end_io
function.
Sync I/O can then be implemented using a callback that signal I/O
completion. This is similar to the logic found in blk_to_execute_io().
By implementing it this way, the underlying device I/Os submission logic
is abstracted away from core, targets, and media managers.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The modified variables are only used in the file mtip32xx.c.
As such, the static keyword is inserted to define that object
to be only visible to the current code module during compilation.
Signed-off-by: Zhu Yanjun <zyjzyj2000@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Lars Ellenberg