When writing to a delalloc region in the data fork, commit the new
allocations (of the da reservation) as unwritten so that the mappings
are only marked written once writeback completes successfully. This
fixes the problem of stale data exposure if the system goes down during
targeted writeback of a specific region of a file, as tested by
generic/042.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Refactor xfs_iomap_prealloc_size to be the function that dynamically
computes the per-file preallocation size by moving the allocsize= case
to the caller. Break up the huge comment preceding the function to
annotate the relevant parts of the code, and remove the impossible
check_writeio case.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
When we're estimating a new speculative preallocation length for an
extending write, we should walk backwards through the extent list to
determine the number of number of blocks that are physically and
logically contiguous with the write offset, and use that as an input to
the preallocation size computation.
This way, preallocation length is truly measured by the effectiveness of
the allocator in giving us contiguous allocations without being
influenced by the state of a given extent. This fixes both the problem
where ZERO_RANGE within an EOF can reduce preallocation, and prevents
the unnecessary shrinkage of preallocation when delalloc extents are
turned into unwritten extents.
This was found as a regression in xfs/014 after changing delalloc writes
to create unwritten extents during writeback.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
During writeback, it's possible for the quota block reservation in
xfs_iomap_write_unwritten to fail with EDQUOT because we hit the quota
limit. This causes writeback errors for data that was already written
to disk, when it's not even guaranteed that the bmbt will expand to
exceed the quota limit. Irritatingly, this condition is reported to
userspace as EIO by fsync, which is confusing.
We wrote the data, so allow the reservation. That might put us slightly
above the hard limit, but it's better than losing data after a write.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The perag structure already has a pointer to the xfs_mount, so we don't
need to pass that separately and can drop it. Having done that, move
iter_flags so that the argument order is the same between xfs_inode_walk
and xfs_inode_walk_ag. The latter will make things less confusing for a
future patch that enables background scanning work to be done in
parallel.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
We're not very consistent about function names for the incore inode
iteration function. Turn them all into xfs_inode_walk* variants.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the xfs_inode_ag_iterator function to be nearer xfs_inode_ag_walk
so that we don't have to scroll back and forth to figure out how the
incore inode walking function works. No functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
This is a boolean variable, so use the bool type.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
There are a number of predicate functions that help the incore inode
walking code decide if we really want to apply the iteration function to
the inode. These are boolean decisions, so change the return types to
boolean to match.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Refactor the two eofb-matching logics into a single helper so that we
don't repeat ourselves.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
This is now a pointless wrapper, so kill it.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
The incore inode walk code passes a flags argument and a pointer from
the xfs_inode_ag_iterator caller all the way to the iteration function.
We can reduce the function complexity by passing flags through the
private pointer.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Combine xfs_inode_ag_iterator_flags and xfs_inode_ag_iterator_tag into a
single wrapper function since there's only one caller of the _flags
variant.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Not used by anyone, so get rid of it.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Use XFS_ICI_NO_TAG instead of -1 when appropriate.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Move xfs_fs_eofblocks_from_user into the only file that actually uses
it, so that we don't have this function cluttering up the header file.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
The only grace period which can be set in the kernel today is for id 0,
i.e. the default grace period for all users. However, setting an
individual grace period is useful; for example:
Alice has a soft quota of 100 inodes, and a hard quota of 200 inodes
Alice uses 150 inodes, and enters a short grace period
Alice really needs to use those 150 inodes past the grace period
The administrator extends Alice's grace period until next Monday
vfs quota users such as ext4 can do this today, with setquota -T
To enable this for XFS, we simply move the timelimit assignment out
from under the (id == 0) test. Default setting remains under (id == 0).
Note that this now is consistent with how we set warnings.
(Userspace requires updates to enable this as well; xfs_quota needs to
parse new options, and setquota needs to set appropriate field flags.)
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Move timers and warnings out of xfs_quotainfo and into xfs_def_quota
so that we can utilize them on a per-type basis, rather than enforcing
them based on the values found in the first enabled quota type.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
[zlang: new way to get defquota in xfs_qm_init_timelimits]
[zlang: remove redundant defq assign]
Signed-off-by: Zorro Lang <zlang@redhat.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
xfs_get_defquota() currently takes an xfs_dquot, and from that obtains
the type of default quota we should get (user/group/project).
But early in init, we don't have access to a fully set up quota, so
that's not possible. The next patch needs go set up default quota
timers early, so switch xfs_get_defquota to take an explicit type
and add a helper function to obtain that type from an xfs_dquot
for the existing callers.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Pass xfs_dquot rather than xfs_disk_dquot to xfs_qm_adjust_dqtimers;
this makes it symmetric with xfs_qm_adjust_dqlimits and will help
the next patch.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
There is a fair bit of whitespace damage in the quota code, so
fix up enough of it that subsequent patches are restricted to
functional change to aid review.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
XFS project quota treats project hierarchies as "mini filesysems" and
so rather than -EDQUOT, the intent is to return -ENOSPC when a quota
reservation fails, but this behavior is not consistent.
The only place we make a decision between -EDQUOT and -ENOSPC
returns based on quota type is in xfs_trans_dqresv().
This behavior is currently controlled by whether or not the
XFS_QMOPT_ENOSPC flag gets passed into the quota reservation. However,
its use is not consistent; paths such as xfs_create() and xfs_symlink()
don't set the flag, so a reservation failure will return -EDQUOT for
project quota reservation failures rather than -ENOSPC for these sorts
of operations, even for project quota:
# mkdir mnt/project
# xfs_quota -x -c "project -s -p mnt/project 42" mnt
# xfs_quota -x -c 'limit -p isoft=2 ihard=3 42' mnt
# touch mnt/project/file{1,2,3}
touch: cannot touch ‘mnt/project/file3’: Disk quota exceeded
We can make this consistent by not requiring the flag to be set at the
top of the callchain; instead we can simply test whether we are
reserving a project quota with XFS_QM_ISPDQ in xfs_trans_dqresv and if
so, return -ENOSPC for that failure. This removes the need for the
XFS_QMOPT_ENOSPC altogether and simplifies the code a fair bit.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Long ago, group & project quota were mutually exclusive, and so
when we turned on XFS_QMOPT_ENOSPC ("return ENOSPC if project quota
is exceeded") when project quota was enabled, we only needed to
disable it again for user quota.
When group & project quota got separated, this got missed, and as a
result if project quota is enabled and group quota is exceeded, the
error code returned is incorrectly returned as ENOSPC not EDQUOT.
Fix this by stripping XFS_QMOPT_ENOSPC out of flags for group
quota when we try to reserve the space.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
It's a global atomic counter, and we are hitting it at a rate of
half a million transactions a second, so it's bouncing the counter
cacheline all over the place on large machines. We don't actually
need it anymore - it used to be required because the VFS freeze code
could not track/prevent filesystem transactions that were running,
but that problem no longer exists.
Hence to remove the counter, we simply have to ensure that nothing
calls xfs_sync_sb() while we are trying to quiesce the filesytem.
That only happens if the log worker is still running when we call
xfs_quiesce_attr(). The log worker is cancelled at the end of
xfs_quiesce_attr() by calling xfs_log_quiesce(), so just call it
early here and then we can remove the counter altogether.
Concurrent create, 50 million inodes, identical 16p/16GB virtual
machines on different physical hosts. Machine A has twice the CPU
cores per socket of machine B:
unpatched patched
machine A: 3m16s 2m00s
machine B: 4m04s 4m05s
Create rates:
unpatched patched
machine A: 282k+/-31k 468k+/-21k
machine B: 231k+/-8k 233k+/-11k
Concurrent rm of same 50 million inodes:
unpatched patched
machine A: 6m42s 2m33s
machine B: 4m47s 4m47s
The transaction rate on the fast machine went from just under
300k/sec to 700k/sec, which indicates just how much of a bottleneck
this atomic counter was.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Seeing massive cpu usage from xfs_agino_range() on one machine;
instruction level profiles look similar to another machine running
the same workload, only one machine is consuming 10x as much CPU as
the other and going much slower. The only real difference between
the two machines is core count per socket. Both are running
identical 16p/16GB virtual machine configurations
Machine A:
25.83% [k] xfs_agino_range
12.68% [k] __xfs_dir3_data_check
6.95% [k] xfs_verify_ino
6.78% [k] xfs_dir2_data_entry_tag_p
3.56% [k] xfs_buf_find
2.31% [k] xfs_verify_dir_ino
2.02% [k] xfs_dabuf_map.constprop.0
1.65% [k] xfs_ag_block_count
And takes around 13 minutes to remove 50 million inodes.
Machine B:
13.90% [k] __pv_queued_spin_lock_slowpath
3.76% [k] do_raw_spin_lock
2.83% [k] xfs_dir3_leaf_check_int
2.75% [k] xfs_agino_range
2.51% [k] __raw_callee_save___pv_queued_spin_unlock
2.18% [k] __xfs_dir3_data_check
2.02% [k] xfs_log_commit_cil
And takes around 5m30s to remove 50 million inodes.
Suspect is cacheline contention on m_sectbb_log which is used in one
of the macros in xfs_agino_range. This is a read-only variable but
shares a cacheline with m_active_trans which is a global atomic that
gets bounced all around the machine.
The workload is trying to run hundreds of thousands of transactions
per second and hence cacheline contention will be occurring on this
atomic counter. Hence xfs_agino_range() is likely just be an
innocent bystander as the cache coherency protocol fights over the
cacheline between CPU cores and sockets.
On machine A, this rearrangement of the struct xfs_mount
results in the profile changing to:
9.77% [kernel] [k] xfs_agino_range
6.27% [kernel] [k] __xfs_dir3_data_check
5.31% [kernel] [k] __pv_queued_spin_lock_slowpath
4.54% [kernel] [k] xfs_buf_find
3.79% [kernel] [k] do_raw_spin_lock
3.39% [kernel] [k] xfs_verify_ino
2.73% [kernel] [k] __raw_callee_save___pv_queued_spin_unlock
Vastly less CPU usage in xfs_agino_range(), but still 3x the amount
of machine B and still runs substantially slower than it should.
Current rm -rf of 50 million files:
vanilla patched
machine A 13m20s 6m42s
machine B 5m30s 5m02s
It's an improvement, hence indicating that separation and further
optimisation of read-only global filesystem data is worthwhile, but
it clearly isn't the underlying issue causing this specific
performance degradation.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Shaokun Zhang reported that XFS was using substantial CPU time in
percpu_count_sum() when running a single threaded benchmark on
a high CPU count (128p) machine from xfs_mod_ifree(). The issue
is that the filesystem is empty when the benchmark runs, so inode
allocation is running with a very low inode free count.
With the percpu counter batching, this means comparisons when the
counter is less that 128 * 256 = 32768 use the slow path of adding
up all the counters across the CPUs, and this is expensive on high
CPU count machines.
The summing in xfs_mod_ifree() is only used to fire an assert if an
underrun occurs. The error is ignored by the higher level code.
Hence this is really just debug code and we don't need to run it
on production kernels, nor do we need such debug checks to return
error values just to trigger an assert.
Finally, xfs_mod_icount/xfs_mod_ifree are only called from
xfs_trans_unreserve_and_mod_sb(), so get rid of them and just
directly call the percpu_counter_add/percpu_counter_compare
functions. The compare functions are now run only on debug builds as
they are internal to ASSERT() checks and so only compiled in when
ASSERTs are active (CONFIG_XFS_DEBUG=y or CONFIG_XFS_WARN=y).
Reported-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
xfs: gut error handling in xfs_trans_unreserve_and_mod_sb()
From: Dave Chinner <dchinner@redhat.com>
The error handling in xfs_trans_unreserve_and_mod_sb() is largely
incorrect - rolling back the changes in the transaction if only one
counter underruns makes all the other counters incorrect. We still
allow the change to proceed and committing the transaction, except
now we have multiple incorrect counters instead of a single
underflow.
Further, we don't actually report the error to the caller, so this
is completely silent except on debug kernels that will assert on
failure before we even get to the rollback code. Hence this error
handling is broken, untested, and largely unnecessary complexity.
Just remove it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The argument isn't used by any caller, and drivers don't fill out
bi_sector for flush requests either.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move freeing the dynamically allocated attr and COW fork, as well
as zeroing the pointers where actually needed into the callers, and
just pass the xfs_ifork structure to xfs_idestroy_fork. Also simplify
the kmem_free calls by not checking for NULL first.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Both the data and attr fork have a format that is stored in the legacy
idinode. Move it into the xfs_ifork structure instead, where it uses
up padding.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
There are there are three extents counters per inode, one for each of
the forks. Two are in the legacy icdinode and one is directly in
struct xfs_inode. Switch to a single counter in the xfs_ifork structure
where it uses up padding at the end of the structure. This simplifies
various bits of code that just wants the number of extents counter and
can now directly dereference it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
xfs_ifree only need to free inline data in the data fork, as we've
already taken care of the attr fork before (and in fact freed the
fork structure). Just open code the freeing of the inline data.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Just checking di_forkoff directly is a little easier to follow.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
XFS_IFORK_Q is supposed to be a predicate, not a function returning a
value. Its usage is in xchk_bmap_check_rmaps is incorrect, but that
function only cares about whether or not the "size" of the data is zero
or not. Convert that logic to use a proper boolean, and teach the
caller to skip the call entirely if the end result would be that we'd do
nothing anyway. This avoids a crash later in this series.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[hch: generalized the NULL ifor check]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Now that we fully verify the inode forks before they are added to the
inode cache, the crash reported in
https://bugzilla.kernel.org/show_bug.cgi?id=204031
can't happen anymore, as we'll never let an inode that has inconsistent
nextents counts vs the presence of an in-core attr fork leak into the
inactivate code path. So remove the work around to try to handle the
case, and just return an error and warn if the fork is not present.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
We don't call xfs_bmapi_read for the COW fork anymore, so remove the
special casing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Call the data/attr local fork verifiers as soon as we are ready for them.
This keeps them close to the code setting up the forks, and avoids a
few branches later on. Also open code xfs_inode_verify_forks in the
only remaining caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The split between xfs_inode_verify_forks and the two helpers
implementing the actual functionality is a little strange. Reshuffle
it so that xfs_inode_verify_forks verifies if the data and attr forks
are actually in local format and only call the low-level helpers if
that is the case. Handle the actual error reporting in the low-level
handlers to streamline the caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
xfs_ifork_ops add up to two indirect calls per inode read and flush,
despite just having a single instance in the kernel. In xfsprogs
phase6 in xfs_repair overrides the verify_dir method to deal with inodes
that do not have a valid parent, but that can be fixed pretty easily
by ensuring they always have a valid looking parent.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
There is not much point in the xfs_iread function, as it has a single
caller and not a whole lot of code. Move it into the only caller,
and trim down the overdocumentation to just documenting the important
"why" instead of a lot of redundant "what".
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
i_delayed_blks is set to 0 in xfs_inode_alloc and can't have anything
assigned to it until the inode is visible to the VFS.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Keep the code dealing with the dinode together, and also ensure we verify
the dinode in the owner change log recovery case as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Handle inodes with a 0 di_mode in xfs_inode_from_disk, instead of partially
duplicating inode reading in xfs_iread.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
xfs_iformat_fork is a weird catchall. Split it into one helper for
the data fork and one for the attr fork, and then call both helper
as well as the COW fork initialization from xfs_inode_from_disk. Order
the COW fork initialization after the attr fork initialization given
that it can't fail to simplify the error handling.
Note that the newly split helpers are moved down the file in
xfs_inode_fork.c to avoid the need for forward declarations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
We always need to fill out the fork structures when reading the inode,
so call xfs_iformat_fork from the tail of xfs_inode_from_disk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The last argument to xfs_bmapi_raad contains XFS_BMAPI_* flags, not the
fork. Given that XFS_DATA_FORK evaluates to 0 no real harm is done,
but let's fix this anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Fix this error message to complain about project and group quota flag
bits instead of "PUOTA" and "QUOTA".
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Since the old SWAPEXT ioctl doesn't know how to adjust quota ids,
bail out of the ids don't match and quotas are enabled.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
While QAing the new xfs_repair quotacheck code, I uncovered a quota
corruption bug resulting from a bad interaction between dquot buffer
initialization and quotacheck. The bug can be reproduced with the
following sequence:
# mkfs.xfs -f /dev/sdf
# mount /dev/sdf /opt -o usrquota
# su nobody -s /bin/bash -c 'touch /opt/barf'
# sync
# xfs_quota -x -c 'report -ahi' /opt
User quota on /opt (/dev/sdf)
Inodes
User ID Used Soft Hard Warn/Grace
---------- ---------------------------------
root 3 0 0 00 [------]
nobody 1 0 0 00 [------]
# xfs_io -x -c 'shutdown' /opt
# umount /opt
# mount /dev/sdf /opt -o usrquota
# touch /opt/man2
# xfs_quota -x -c 'report -ahi' /opt
User quota on /opt (/dev/sdf)
Inodes
User ID Used Soft Hard Warn/Grace
---------- ---------------------------------
root 1 0 0 00 [------]
nobody 1 0 0 00 [------]
# umount /opt
Notice how the initial quotacheck set the root dquot icount to 3
(rootino, rbmino, rsumino), but after shutdown -> remount -> recovery,
xfs_quota reports that the root dquot has only 1 icount. We haven't
deleted anything from the filesystem, which means that quota is now
under-counting. This behavior is not limited to icount or the root
dquot, but this is the shortest reproducer.
I traced the cause of this discrepancy to the way that we handle ondisk
dquot updates during quotacheck vs. regular fs activity. Normally, when
we allocate a disk block for a dquot, we log the buffer as a regular
(dquot) buffer. Subsequent updates to the dquots backed by that block
are done via separate dquot log item updates, which means that they
depend on the logged buffer update being written to disk before the
dquot items. Because individual dquots have their own LSN fields, that
initial dquot buffer must always be recovered.
However, the story changes for quotacheck, which can cause dquot block
allocations but persists the final dquot counter values via a delwri
list. Because recovery doesn't gate dquot buffer replay on an LSN, this
means that the initial dquot buffer can be replayed over the (newer)
contents that were delwritten at the end of quotacheck. In effect, this
re-initializes the dquot counters after they've been updated. If the
log does not contain any other dquot items to recover, the obsolete
dquot contents will not be corrected by log recovery.
Because quotacheck uses a transaction to log the setting of the CHKD
flags in the superblock, we skip quotacheck during the second mount
call, which allows the incorrect icount to remain.
Fix this by changing the ondisk dquot initialization function to use
ordered buffers to write out fresh dquot blocks if it detects that we're
running quotacheck. If the system goes down before quotacheck can
complete, the CHKD flags will not be set in the superblock and the next
mount will run quotacheck again, which can fix uninitialized dquot
buffers. This requires amending the defer code to maintaine ordered
buffer state across defer rolls for the sake of the dquot allocation
code.
For regular operations we preserve the current behavior since the dquot
items require properly initialized ondisk dquot records.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The attr fork can transition from shortform to leaf format while
empty if the first xattr doesn't fit in shortform. While this empty
leaf block state is intended to be transient, it is technically not
due to the transactional implementation of the xattr set operation.
We historically have a couple of bandaids to work around this
problem. The first is to hold the buffer after the format conversion
to prevent premature writeback of the empty leaf buffer and the
second is to bypass the xattr count check in the verifier during
recovery. The latter assumes that the xattr set is also in the log
and will be recovered into the buffer soon after the empty leaf
buffer is reconstructed. This is not guaranteed, however.
If the filesystem crashes after the format conversion but before the
xattr set that induced it, only the format conversion may exist in
the log. When recovered, this creates a latent corrupted state on
the inode as any subsequent attempts to read the buffer fail due to
verifier failure. This includes further attempts to set xattrs on
the inode or attempts to destroy the attr fork, which prevents the
inode from ever being removed from the unlinked list.
To avoid this condition, accept that an empty attr leaf block is a
valid state and remove the count check from the verifier. This means
that on rare occasions an attr fork might exist in an unexpected
state, but is otherwise consistent and functional. Note that we
retain the logic to avoid racing with metadata writeback to reduce
the window where this can occur.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
This patch corrects the SPDX License Identifier style in header files
related to XFS File System support. For C header files
Documentation/process/license-rules.rst mandates C-like comments.
(opposed to C source files where C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
DCACHE_DONTCACHE indicates a dentry should not be cached on final
dput().
Also add a helper function to mark DCACHE_DONTCACHE on all dentries
pointing to a specific inode when that inode is being set I_DONTCACHE.
This facilitates dropping dentry references to inodes sooner which
require eviction to swap S_DAX mode.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
DAX effective mode (S_DAX) changes requires inode eviction.
XFS has an advisory flag (XFS_IDONTCACHE) to prevent caching of the
inode if no other additional references are taken. We lift this flag to
the VFS layer and change the behavior slightly by allowing the flag to
remain even if multiple references are taken.
This will expedite the eviction of inodes to change S_DAX.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Remove duplicate headers which are included twice.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The random buffer write failure errortag patch introduced a local
mount pointer variable for the test macro, but the macro is compiled
out on !DEBUG kernels. This results in an unused variable warning.
Access the mount structure through the buffer pointer and remove the
local mount pointer to address the warning.
Fixes: 7376d74547 ("xfs: random buffer write failure errortag")
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Remove unnecessary includes from the log recovery code.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Move the helpers that handle incore buffer cancellation records to
xfs_buf_item_recover.c since they're not directly related to the main
log recovery machinery. No functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The only purpose of XFS_LI_RECOVERED is to prevent log recovery from
trying to replay recovered intents more than once. Therefore, we can
move the bit setting up to the ->iop_recover caller.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Now that we've made the recovered item tests all the same, we can hoist
the test and the ail locking code to the ->iop_recover caller and call
the recovery function directly.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Rename XFS_{EFI,BUI,RUI,CUI}_RECOVERED to XFS_LI_RECOVERED so that we
track recovery status in the log item, then get rid of the now unused
flags fields in each of those log item types.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
During recovery, every intent that we recover from the log has to be
added to the AIL. Replace the open-coded addition with a helper.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Replace the open-coded AIL item walking with a proper helper when we're
trying to release an intent item that has been finished. We add a new
->iop_match method to decide if an intent item matches a supplied ID.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Now that we've finished converting all types of log intent items to
provide an ->iop_recover function, we can convert the "is this an intent
item?" predicate to look for a non-null iop_recover pointer.
Move the predicate closer to the functions that use it.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the code that processes the log items created from the recovered
log items into the per-item source code files and use dispatch functions
to call them. No functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the code that processes the log items created from the recovered
log items into the per-item source code files and use dispatch functions
to call them. No functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the code that processes the log items created from the recovered
log items into the per-item source code files and use dispatch functions
to call them. No functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the code that processes the log items created from the recovered
log items into the per-item source code files and use dispatch functions
to call them. No functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Quotaoff doesn't actually do anything, so take advantage of the
commit_pass2 pointer being optional and get rid of the switch
statement clause.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the bmap update intent and intent-done pass2 commit code into the
per-item source code files and use dispatch functions to call them. We
do these one at a time because there's a lot of code to move. No
functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the refcount update intent and intent-done pass2 commit code into
the per-item source code files and use dispatch functions to call them.
We do these one at a time because there's a lot of code to move. No
functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the rmap update intent and intent-done pass2 commit code into the
per-item source code files and use dispatch functions to call them. We
do these one at a time because there's a lot of code to move. No
functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the extent free intent and intent-done pass2 commit code into the
per-item source code files and use dispatch functions to call them. We
do these one at a time because there's a lot of code to move. No
functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the log icreate item pass2 commit code into the per-item source code
files and use the dispatch function to call it. We do these one at a
time because there's a lot of code to move. No functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the log dquot item pass2 commit code into the per-item source code
files and use the dispatch function to call it. We do these one at a
time because there's a lot of code to move. No functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the log inode item pass2 commit code into the per-item source code
files and use the dispatch function to call it. We do these one at a
time because there's a lot of code to move. No functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the log buffer item pass2 commit code into the per-item source code
files and use the dispatch function to call it. We do these one at a
time because there's a lot of code to move. No functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the pass1 commit code into the per-item source code files and use
the dispatch function to call them.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the pass2 readhead code into the per-item source code files and use
the dispatch function to call them.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Create a generic dispatch structure to delegate recovery of different
log item types into various code modules. This will enable us to move
code specific to a particular log item type out of xfs_log_recover.c and
into the log item source.
The first operation we virtualize is the log item sorting.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Remove the old typedefs.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
iget_flags is unused in xfs_imap_to_bp(). Remove the parameter and
fix up the callers.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Both types control shutdown messaging and neither is used in the
current codebase.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Introduce an error tag to randomly fail async buffer writes. This is
primarily to facilitate testing of the XFS error configuration
mechanism.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The stale parameter was used to control the now unused shutdown
parameter of xfs_trans_ail_remove().
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Now that the functions and callers of
xfs_trans_ail_[remove|delete]() have been fixed up appropriately,
the only difference between the two is the shutdown behavior. There
are only a few callers of the _remove() variant, so make the
shutdown conditional on the parameter and combine the two functions.
Suggested-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The shutdown parameter of xfs_trans_ail_remove() is no longer used.
The remaining callers use it for items that legitimately might not
be in the AIL or from contexts where AIL state has already been
checked. Remove the unnecessary parameter and fix up the callers.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Various intent log items call xfs_trans_ail_remove() with a log I/O
error shutdown type, but this helper historically checks whether an
item is in the AIL before calling xfs_trans_ail_delete(). This means
the shutdown check is essentially a no-op for users of
xfs_trans_ail_remove().
It is possible that some items might not be AIL resident when the
AIL remove attempt occurs, but this should be isolated to cases
where the filesystem has already shutdown. For example, this
includes abort of the transaction committing the intent and I/O
error of the iclog buffer committing the intent to the log.
Therefore, update these callsites to use xfs_trans_ail_delete() to
provide AIL state validation for the common path of items being
released and removed when associated done items commit to the
physical log.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Several callers acquire the lock just prior to the call. Callers
that require ->ail_lock for other purposes already check IN_AIL
state and thus don't require the additional shutdown check in the
helper. Push the lock down into xfs_trans_ail_delete(), open code
the instances that still acquire it, and remove the unnecessary ailp
parameter.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The dquot flush handler effectively aborts the dquot flush if the
filesystem is already shut down, but doesn't actually shut down if
the flush fails. Update xfs_qm_dqflush() to consistently abort the
dquot flush and shutdown the fs if the flush fails with an
unexpected error.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The pre-flush dquot verification in xfs_qm_dqflush() duplicates the
read verifier by checking the dquot in the on-disk buffer. Instead,
verify the in-core variant before it is flushed to the buffer.
Fixes: 7224fa482a ("xfs: add full xfs_dqblk verifier")
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
At unmount time, XFS emits an alert for every in-core buffer that
might have undergone a write error. In practice this behavior is
probably reasonable given that the filesystem is likely short lived
once I/O errors begin to occur consistently. Under certain test or
otherwise expected error conditions, this can spam the logs and slow
down the unmount.
Now that we have a ratelimit mechanism specifically for buffer
alerts, reuse it for the per-buffer alerts in xfs_wait_buftarg().
Also lift the final repair message out of the loop so it always
prints and assert that the metadata error handling code has shut
down the fs.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
XFS has some inconsistent log message rate limiting with respect to
buffer alerts. The metadata I/O error notification uses the generic
ratelimited alert, the buffer push code uses a custom rate limit and
the similar quiesce time failure checks are not rate limited at all
(when they should be).
The custom rate limit defined in the buf item code is specifically
crafted for buffer alerts. It is more aggressive than generic rate
limiting code because it must accommodate a high frequency of I/O
error events in a relative short timeframe.
Factor out the custom rate limit state from the buf item code into a
per-buftarg rate limit so various alerts are limited based on the
target. Define a buffer alert helper function and use it for the
buffer alerts that are already ratelimited.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The buffer write failure flag is intended to control the internal
write retry that XFS has historically implemented to help mitigate
the severity of transient I/O errors. The flag is set when a buffer
is resubmitted from the I/O completion path due to a previous
failure. It is checked on subsequent I/O completions to skip the
internal retry and fall through to the higher level configurable
error handling mechanism. The flag is cleared in the synchronous and
delwri submission paths and also checked in various places to log
write failure messages.
There are a couple minor problems with the current usage of this
flag. One is that we issue an internal retry after every submission
from xfsaild due to how delwri submission clears the flag. This
results in double the expected or configured number of write
attempts when under sustained failures. Another more subtle issue is
that the flag is never cleared on successful I/O completion. This
can cause xfs_wait_buftarg() to suggest that dirty buffers are being
thrown away due to the existence of the flag, when the reality is
that the flag might still be set because the write succeeded on the
retry.
Clear the write failure flag on successful I/O completion to address
both of these problems. This means that the internal retry attempt
occurs once since the last time a buffer write failed and that
various other contexts only see the flag set when the immediately
previous write attempt has failed.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The shutdown check in xfs_iflush() duplicates checks down in the
buffer code. If the fs is shut down, xfs_trans_read_buf_map() always
returns an error and falls into the same error path. Remove the
unnecessary check along with the warning in xfs_imap_to_bp()
that generates excessive noise in the log if the fs is shut down.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The inode flush code has several layers of error handling between
the inode and cluster flushing code. If the inode flush fails before
acquiring the backing buffer, the inode flush is aborted. If the
cluster flush fails, the current inode flush is aborted and the
cluster buffer is failed to handle the initial inode and any others
that might have been attached before the error.
Since xfs_iflush() is the only caller of xfs_iflush_cluster(), the
error handling between the two can be condensed in the top-level
function. If we update xfs_iflush_int() to always fall through to
the log item update and attach the item completion handler to the
buffer, any errors that occur after the first call to
xfs_iflush_int() can be handled with a buffer I/O failure.
Lift the error handling from xfs_iflush_cluster() into xfs_iflush()
and consolidate with the existing error handling. This also replaces
the need to release the buffer because failing the buffer with
XBF_ASYNC drops the current reference.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
We use the same buffer I/O failure code in a few different places.
It's not much code, but it's not necessarily self-explanatory.
Factor it into a helper and document it in one place.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Flush locked log items whose underlying buffers fail metadata
writeback are tagged with a special flag to indicate that the flush
lock is already held. This is currently implemented in the type
specific ->iop_push() callback, but the processing required for such
items is not type specific because we're only doing basic state
management on the underlying buffer.
Factor the failed log item handling out of the inode and dquot
->iop_push() callbacks and open code the buffer resubmit helper into
a single helper called from xfsaild_push_item(). This provides a
generic mechanism for handling failed metadata buffer writeback with
a bit less code.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Make sure we release resources properly if we cannot clean out the COW
extents in preparation for an extent swap.
Fixes: 96987eea53 ("xfs: cancel COW blocks before swapext")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Darrick J. Wong