drivers/net/wireless/ath/ath11k/thermal.h:45:1:
warning: no return statement in function returning non-void [-Wreturn-type]
drivers/net/wireless/ath/ath11k/core.c:416:28: error:
passing argument 1 of 'ath11k_thermal_unregister' from incompatible pointer type [-Werror=incompatible-pointer-types]
Add missing return 0 in ath11k_thermal_set_throttling,
and fix ath11k_thermal_unregister param type.
Fixes: 2a63bbca06 ("ath11k: add thermal cooling device support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200403083414.31392-1-yuehaibing@huawei.com
The 2nd gmac of mediatek soc ethernet may not be connected to a PHY
and a phy-handle isn't always available.
Unfortunately, mt7530 dsa driver assumes that the 2nd gmac is always
connected to switch port 5 and setup mt7530 according to phy address
of 2nd gmac node, causing null pointer dereferencing when phy-handle
isn't defined in dts.
This commit fix this setup code by checking return value of
of_parse_phandle before using it.
Fixes: 38f790a805 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the power-down bit is cleared, the chip internally triggers a
global reset. According to the KSZ9031 documentation, we have to wait at
least 1ms for the reset to finish.
If the chip is accessed during reset, read will return 0xffff, while
write will be ignored. Depending on the system performance and MDIO bus
speed, we may or may not run in to this issue.
This bug was discovered on an iMX6QP system with KSZ9031 PHY and
attached PHY interrupt line. If IRQ was used, the link status update was
lost. In polling mode, the link status update was always correct.
The investigation showed, that during a read-modify-write access, the
read returned 0xffff (while the chip was still in reset) and
corresponding write hit the chip _after_ reset and triggered (due to the
0xffff) another reset in an undocumented bit (register 0x1f, bit 1),
resulting in the next write being lost due to the new reset cycle.
This patch fixes the issue by adding a 1...2 ms sleep after the
genphy_resume().
Fixes: 836384d250 ("net: phy: micrel: Add specific suspend")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9463c44559 ("net: stmmac: dwmac1000: Clear unused address
entries") cleared the unused mac address entries, but introduced an
out-of bounds mac address register programming bug -- After setting
the secondary unicast mac addresses, the "reg" value has reached
netdev_uc_count() + 1, thus we should only clear address entries
if (addr < perfect_addr_number)
Fixes: 9463c44559 ("net: stmmac: dwmac1000: Clear unused address entries")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=deWu
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Revert sysfs "rescan" renames that broke apps (Kelsey Skunberg)
- Add more 32 GT/s link speed decoding and improve the implementation
(Yicong Yang)
Resource management:
- Add support for sizing programmable host bridge apertures and fix a
related alpha Nautilus regression (Ivan Kokshaysky)
Interrupts:
- Add boot interrupt quirk mechanism for Xeon chipsets and document
boot interrupts (Sean V Kelley)
PCIe native device hotplug:
- When possible, disable in-band presence detect and use PDS
(Alexandru Gagniuc)
- Add DMI table for devices that don't use in-band presence detection
but don't advertise that correctly (Stuart Hayes)
- Fix hang when powering slots up/down via sysfs (Lukas Wunner)
- Fix an MSI interrupt race (Stuart Hayes)
Virtualization:
- Add ACS quirks for Zhaoxin devices (Raymond Pang)
Error handling:
- Add Error Disconnect Recover (EDR) support so firmware can report
devices disconnected via DPC and we can try to recover (Kuppuswamy
Sathyanarayanan)
Peer-to-peer DMA:
- Add Intel Sky Lake-E Root Ports B, C, D to the whitelist (Andrew
Maier)
ASPM:
- Reduce severity of common clock config message (Chris Packham)
- Clear the correct bits when enabling L1 substates, so we don't go
to the wrong state (Yicong Yang)
Endpoint framework:
- Replace EPF linkup ops with notifier call chain and improve locking
(Kishon Vijay Abraham I)
- Fix concurrent memory allocation in OB address region (Kishon Vijay
Abraham I)
- Move PF function number assignment to EPC core to support multiple
function creation methods (Kishon Vijay Abraham I)
- Fix issue with clearing configfs "start" entry (Kunihiko Hayashi)
- Fix issue with endpoint MSI-X ignoring BAR Indicator and Table
Offset (Kishon Vijay Abraham I)
- Add support for testing DMA transfers (Kishon Vijay Abraham I)
- Add support for testing > 10 endpoint devices (Kishon Vijay Abraham I)
- Add support for tests to clear IRQ (Kishon Vijay Abraham I)
- Add common DT schema for endpoint controllers (Kishon Vijay Abraham I)
Amlogic Meson PCIe controller driver:
- Add DT bindings for AXG PCIe PHY, shared MIPI/PCIe analog PHY (Remi
Pommarel)
- Add Amlogic AXG PCIe PHY, AXG MIPI/PCIe analog PHY drivers (Remi
Pommarel)
Cadence PCIe controller driver:
- Add Root Complex/Endpoint DT schema for Cadence PCIe (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Add two VMD Device IDs that require bus restriction mode (Sushma
Kalakota)
Mobiveil PCIe controller driver:
- Refactor and modularize mobiveil driver (Hou Zhiqiang)
- Add support for Mobiveil GPEX Gen4 host (Hou Zhiqiang)
Microsoft Hyper-V host bridge driver:
- Add support for Hyper-V PCI protocol version 1.3 and
PCI_BUS_RELATIONS2 (Long Li)
- Refactor to prepare for virtual PCI on non-x86 architectures (Boqun
Feng)
- Fix memory leak in hv_pci_probe()'s error path (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Use pci_parse_request_of_pci_ranges() (Rob Herring)
- Add support for endpoint mode and related DT updates (Vidya Sagar)
- Reduce -EPROBE_DEFER error message log level (Thierry Reding)
Qualcomm PCIe controller driver:
- Restrict class fixup to specific Qualcomm devices (Bjorn Andersson)
Synopsys DesignWare PCIe controller driver:
- Refactor core initialization code for endpoint mode (Vidya Sagar)
- Fix endpoint MSI-X to use correct table address (Kishon Vijay
Abraham I)
TI DRA7xx PCIe controller driver:
- Fix MSI IRQ handling (Vignesh Raghavendra)
TI Keystone PCIe controller driver:
- Allow AM654 endpoint to raise MSI-X interrupt (Kishon Vijay Abraham I)
Miscellaneous:
- Quirk ASMedia XHCI USB to avoid "PME# from D0" defect (Kai-Heng
Feng)
- Use ioremap(), not phys_to_virt(), for platform ROM to fix video
ROM mapping with CONFIG_HIGHMEM (Mikel Rychliski)"
* tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (96 commits)
misc: pci_endpoint_test: remove duplicate macro PCI_ENDPOINT_TEST_STATUS
PCI: tegra: Print -EPROBE_DEFER error message at debug level
misc: pci_endpoint_test: Use full pci-endpoint-test name in request_irq()
misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
tools: PCI: Add 'e' to clear IRQ
misc: pci_endpoint_test: Add ioctl to clear IRQ
misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
PCI: keystone: Allow AM654 PCIe Endpoint to raise MSI-X interrupt
PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address
PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments
misc: pci_endpoint_test: Add support to get DMA option from userspace
tools: PCI: Add 'd' command line option to support DMA
misc: pci_endpoint_test: Use streaming DMA APIs for buffer allocation
PCI: endpoint: functions/pci-epf-test: Print throughput information
PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data
PCI: pciehp: Fix MSI interrupt race
PCI: pciehp: Fix indefinite wait on sysfs requests
PCI: endpoint: Fix clearing start entry in configfs
PCI: tegra: Add support for PCIe endpoint mode in Tegra194
PCI: sysfs: Revert "rescan" file renames
...
Here are 3 SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your current
tree, that should be trivial to handle (one file modified by two things,
one file deleted.)
All 3 of these have been in linux-next for a while, with no reported
issues other than the merge conflict.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodg5A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykySQCgy9YDrkz7nWq6v3Gohl6+lW/L+rMAnRM4uTZm
m5AuCzO3Azt9KBi7NL+L
=2Lm5
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here are three SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your
current tree, that should be trivial to handle (one file modified by
two things, one file deleted.)
All three of these have been in linux-next for a while, with no
reported issues other than the merge conflict"
* tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
ASoC: MT6660: make spdxcheck.py happy
.gitignore: add SPDX License Identifier
.gitignore: remove too obvious comments
Shifting the integer value 1 is evaluated using 32-bit
arithmetic and then used in an expression that expects a 64-bit
value, so there is potentially an integer overflow. Fix this
by using the BIT_ULL macro to perform the shift and avoid the
overflow.
Addresses-Coverity: ("Unintentional integer overflow")
Fixes: 13f2e64b94 ("mlxsw: spectrum_trap: Add devlink-trap policer support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove pegasus' own workqueue and replace it with system_long_wq.
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 907a076881, forgot that we need to clear old values of
XGMAC_VLAN_TAG register when we switch from VLAN perfect matching to
HASH matching.
Fix it.
Fixes: 907a076881 ("net: stmmac: xgmac: fix incorrect XGMAC_VLAN_TAG register writting")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CAVIUM_PTP is m and THUNDER_NIC_VF is y, build fails:
drivers/net/ethernet/cavium/thunder/nicvf_main.o: In function 'nicvf_remove':
nicvf_main.c:(.text+0x1f0): undefined reference to 'cavium_ptp_put'
drivers/net/ethernet/cavium/thunder/nicvf_main.o: In function `nicvf_probe':
nicvf_main.c:(.text+0x557c): undefined reference to 'cavium_ptp_get'
THUNDER_NIC_VF imply CAVIUM_PTP, which allow the config now,
Use IS_REACHABLE() to avoid the vmlinux link error for this case.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: def2fbffe6 ("kconfig: allow symbols implied by y to become m")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rec->llc is currently being assigned twice, once with the lower 8 bits
from packed_record[8] and then re-assigned afterwards with data from
packed_record[9]. This looks like a type, I believe the second assignment
should be using the |= operator rather than a direct assignment.
Addresses-Coverity: ("Unused value")
Fixes: b8f8a0b7b5 ("net: atlantic: MACSec ingress offload HW bindings")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Igor Russkikh <irusskikh@marell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows the changelink operation to succeed if the mux_id was
specified as an argument. Note that the mux_id must match the
existing mux_id of the rmnet device or should be an unused mux_id.
Fixes: 1dc49e9d16 ("net: rmnet: do not allow to change mux id if mux id is duplicated")
Reported-and-tested-by: Alex Elder <elder@linaro.org>
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The majority of the patches are cleanups, refactorings and clarity
improvements
- Various driver updates for siw, bnxt_re, rxe, efa, mlx5, hfi1
- Lots of cleanup patches for hns
- Convert more places to use refcount
- Aggressively lock the RDMA CM code that syzkaller says isn't working
- Work to clarify ib_cm
- Use the new ib_device lifecycle model in bnxt_re
- Fix mlx5's MR cache which seems to be failing more often with the new
ODP code
- mlx5 'dynamic uar' and 'tx steering' user interfaces
-----BEGIN PGP SIGNATURE-----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=ae+a
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"The majority of the patches are cleanups, refactorings and clarity
improvements.
This cycle saw some more activity from Syzkaller, I think we are now
clean on all but one of those bugs, including the long standing and
obnoxious rdma_cm locking design defect. Continue to see many drivers
getting cleanups, with a few new user visible features.
Summary:
- Various driver updates for siw, bnxt_re, rxe, efa, mlx5, hfi1
- Lots of cleanup patches for hns
- Convert more places to use refcount
- Aggressively lock the RDMA CM code that syzkaller says isn't
working
- Work to clarify ib_cm
- Use the new ib_device lifecycle model in bnxt_re
- Fix mlx5's MR cache which seems to be failing more often with the
new ODP code
- mlx5 'dynamic uar' and 'tx steering' user interfaces"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (144 commits)
RDMA/bnxt_re: make bnxt_re_ib_init static
IB/qib: Delete struct qib_ivdev.qp_rnd
RDMA/hns: Fix uninitialized variable bug
RDMA/hns: Modify the mask of QP number for CQE of hip08
RDMA/hns: Reduce the maximum number of extend SGE per WQE
RDMA/hns: Reduce PFC frames in congestion scenarios
RDMA/mlx5: Add support for RDMA TX flow table
net/mlx5: Add support for RDMA TX steering
IB/hfi1: Call kobject_put() when kobject_init_and_add() fails
IB/hfi1: Fix memory leaks in sysfs registration and unregistration
IB/mlx5: Move to fully dynamic UAR mode once user space supports it
IB/mlx5: Limit the scope of struct mlx5_bfreg_info to mlx5_ib
IB/mlx5: Extend QP creation to get uar page index from user space
IB/mlx5: Extend CQ creation to get uar page index from user space
IB/mlx5: Expose UAR object and its alloc/destroy commands
IB/hfi1: Get rid of a warning
RDMA/hns: Remove redundant judgment of qp_type
RDMA/hns: Remove redundant assignment of wc->smac when polling cq
RDMA/hns: Remove redundant qpc setup operations
RDMA/hns: Remove meaningless prints
...
If we don't have any filters available we can't rely upon the return
code of stmmac_add_hw_vlan_rx_fltr() / stmmac_del_hw_vlan_rx_fltr(). Add
a check for this.
Fixes: ed64639bc1 ("net: stmmac: Add support for VLAN Rx filtering")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not right in grammar to spell "Its not". The right one is "It's
not".
And this line is also over 80 characters. So I broke it into two lines
as well in order to make that line not be more than 80 characters.
Signed-off-by: Hu Haowen <xianfengting221@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"its not" is wrong. The words should be "it's not".
Signed-off-by: Hu Haowen <xianfengting221@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct can_frame contains some padding which is not explicitly zeroed in
slc_bump. This uninitialized data will then be transmitted if the stack
initialization hardening feature is not enabled (CONFIG_INIT_STACK_ALL).
This commit just zeroes the whole struct including the padding.
Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com>
Fixes: a1044e36e4 ("can: add slcan driver for serial/USB-serial CAN adapters")
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: security@kernel.org
Cc: wg@grandegger.com
Cc: mkl@pengutronix.de
Cc: davem@davemloft.net
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The masks in priv->clk_25m_reg and priv->clk_25m_mask are one-bits-set
for the values that comprise the fields, not zero-bits-set.
This patch fixes the clock frequency configuration for ATH8030 and
ATH8035 Atheros PHYs by removing the erroneous "~".
To reproduce this bug, configure the PHY with the device tree binding
"qca,clk-out-frequency" and remove the machine specific PHY fixups.
Fixes: 2f664823a4 ("net: phy: at803x: add device tree binding")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4_update_mac_filt() earlier requests firmware to add a new MAC
address into MPS TCAM. The MPS TCAM index returned by firmware is
stored in pi->xact_addr_filt. However, the saved MPS TCAM index gets
overwritten again with the return value of cxgb4_update_mac_filt(),
which is wrong.
When trying to update to another MAC address later, the wrong MPS TCAM
index is sent to firmware, which causes firmware to return error,
because it's not the same MPS TCAM index that firmware had sent
earlier to driver.
So, fix by removing the wrong overwrite being done after call to
cxgb4_update_mac_filt().
Fixes: 3f8cfd0d95 ("cxgb4/cxgb4vf: Program hash region for {t4/t4vf}_change_mac()")
Signed-off-by: Herat Ramani <herat@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, CONFIG_VHOST depends on CONFIG_VIRTUALIZATION. But vhost is
not necessarily for VM since it's a generic userspace and kernel
communication protocol. Such dependency may prevent archs without
virtualization support from using vhost.
To solve this, a dedicated vhost menu is created under drivers so
CONIFG_VHOST can be decoupled out of CONFIG_VIRTUALIZATION.
While at it, also squash Kconfig.vringh into vhost Kconfig file. This
avoids the trick of conditional inclusion from VOP or CAIF. Then it
will be easier to introduce new vringh users and common dependency for
both vringh and vhost.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20200326140125.19794-2-jasowang@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
[Build system]
- add CONFIG_UNUSED_KSYMS_WHITELIST, which will be useful to define
a fixed set of export symbols for Generic Kernel Image (GKI)
- allow to run 'make dt_binding_check' without .config
- use full schema for checking DT examples in *.yaml files
- make modpost fail for missing MODULE_IMPORT_NS(), which makes more
sense because we know the produced modules are never loadable
- Remove unused 'AS' variable
[Kconfig]
- sanitize DEFCONFIG_LIST, and remove ARCH_DEFCONFIG from Kconfig files
- relax the 'imply' behavior so that symbols implied by y can become m
- make 'imply' obey 'depends on' in order to make 'imply' really weak
[Misc]
- add documentation on building the kernel with Clang/LLVM
- revive __HAVE_ARCH_STRLEN for 32bit sparc to use optimized strlen()
- fix warning from deb-pkg builds when CONFIG_DEBUG_INFO=n
- various script and Makefile cleanups
-----BEGIN PGP SIGNATURE-----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=wT8A
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
"Build system:
- add CONFIG_UNUSED_KSYMS_WHITELIST, which will be useful to define a
fixed set of export symbols for Generic Kernel Image (GKI)
- allow to run 'make dt_binding_check' without .config
- use full schema for checking DT examples in *.yaml files
- make modpost fail for missing MODULE_IMPORT_NS(), which makes more
sense because we know the produced modules are never loadable
- Remove unused 'AS' variable
Kconfig:
- sanitize DEFCONFIG_LIST, and remove ARCH_DEFCONFIG from Kconfig
files
- relax the 'imply' behavior so that symbols implied by 'y' can
become 'm'
- make 'imply' obey 'depends on' in order to make 'imply' really weak
Misc:
- add documentation on building the kernel with Clang/LLVM
- revive __HAVE_ARCH_STRLEN for 32bit sparc to use optimized strlen()
- fix warning from deb-pkg builds when CONFIG_DEBUG_INFO=n
- various script and Makefile cleanups"
* tag 'kbuild-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (34 commits)
Makefile: Update kselftest help information
kbuild: deb-pkg: fix warning when CONFIG_DEBUG_INFO is unset
kbuild: add outputmakefile to no-dot-config-targets
kbuild: remove AS variable
net: wan: wanxl: refactor the firmware rebuild rule
net: wan: wanxl: use $(M68KCC) instead of $(M68KAS) for rebuilding firmware
net: wan: wanxl: use allow to pass CROSS_COMPILE_M68k for rebuilding firmware
kbuild: add comment about grouped target
kbuild: add -Wall to KBUILD_HOSTCXXFLAGS
kconfig: remove unused variable in qconf.cc
sparc: revive __HAVE_ARCH_STRLEN for 32bit sparc
kbuild: refactor Makefile.dtbinst more
kbuild: compute the dtbs_install destination more simply
Makefile: disallow data races on gcc-10 as well
kconfig: make 'imply' obey the direct dependency
kconfig: allow symbols implied by y to become m
net: drop_monitor: use IS_REACHABLE() to guard net_dm_hw_report()
modpost: return error if module is missing ns imports and MODULE_ALLOW_MISSING_NAMESPACE_IMPORTS=n
modpost: rework and consolidate logging interface
kbuild: allow to run dt_binding_check without kernel configuration
...
Included nic tls statistics in ethtool stats.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixed-link nodes are treated as PHY nodes by of_mdiobus_child_is_phy().
We must check if the interface is a fixed-link before looking up for PHY
nodes.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ protocol tag is needed by the KSZ DSA drivers.
Fixes: 0b9f9dfbfa ("dsa: Allow tag drivers to be built as modules")
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case memory resources for dummy_data were allocated, release them
before return.
Addresses-Coverity-ID: 1491997 ("Resource leak")
Fixes: 7ef19d3b1d ("devlink: report error once U32_MAX snapshot ids have been used")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add EHL PSE0/1 RGMII & SGMII 1Gbps PCI info and PCI ID
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As stmmac_pci.c file is getting bigger and more complex, it is reasonable
to separate all the Intel specific dwmac pci device to a different file.
This move includes Intel Quark, TGL and EHL. A new kernel config
CONFIG_DWMAC_INTEL is introduced and depends on X86. For this initial
patch, all the necessary function such as probe() and exit() are identical
besides the function name.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port to which the ASP is connected on 7278 is not capable of
processing VLAN tags as part of the Ethernet frame, so allow an user to
configure the egress VLAN policy they want to see applied by purposing
the h_ext.data[1] field. Bit 0 is used to indicate that 0=tagged,
1=untagged.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update relevant code paths to support the programming and matching of
VLAN TCI, this is the only member of the ethtool_flow_ext that we can
match, the switch does not permit matching the VLAN Ethernet Type field.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for matching VLANs, move the writing of CFP_DATA(5) into
the IPv4 and IPv6 slicing logic since they are part of the per-flow
configuration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not currently support matching on FLOW_EXT or FLOW_MAC_EXT, but we
were not checking for those bits being set in the flow specification.
The check for FLOW_EXT and FLOW_MAC_EXT are separated out because a
subsequent commit will add support for matching VLAN TCI which are
covered by FLOW_EXT.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't want to enable learning for the ASP port since it only receives
directed traffic, this allows us to bypass ARL-driven forwarding rules
which could conflict with Broadcom tags and/or CFP forwarding.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 7278, port 7 connects to the ASP which should only receive frames
through the use of CFP rules, it is not desirable to have it be part of
a bridge at all since that would make it pick up unwanted traffic that
it may not even be able to filter or sustain.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 7278, port 7 of the switch connects to the ASP UniMAC which is not
capable of processing VLAN tagged frames. We can still allow the port to
be part of a VLAN entry, and we may want it to be untagged on egress on
that VLAN because of that limitation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first time b53_configure_vlan() is called we have not configured any
VLAN entries yet, since that happens later when interfaces get brought
up. When b53_configure_vlan() is called again from suspend/resume we
need to restore all VLAN entries though.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f949a12fd6 ("net: dsa: bcm_sf2: fix buffer overflow doing
set_rxnfc") tried to fix the some user controlled buffer overflows in
bcm_sf2_cfp_rule_set() and bcm_sf2_cfp_rule_del() but the fix was using
CFP_NUM_RULES, which while it is correct not to overflow the bitmaps, is
not representative of what the device actually supports. Correct that by
using bcm_sf2_cfp_rule_size() instead.
The latter subtracts the number of rules by 1, so change the checks from
greater than or equal to greater than accordingly.
Fixes: f949a12fd6 ("net: dsa: bcm_sf2: fix buffer overflow doing set_rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vzalloc_node(), already rounds the total size to whole pages, and
sizeof(u64) is smaller than sizeof(struct recv_comp_data). So
round_up of recv_completion_cnt is not necessary, and may cause extra
memory allocation.
To save memory, remove this unnecessary round_up for recv_completion_cnt.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for setting of packet trap group parameters by
invoking the trap_group_init() callback with the new parameters.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some packet traps are currently exposed to user space as being member of
"l3_drops" trap group, but internally they are member of a different
group.
Switch these traps to use the correct group so that they are all subject
to the same policer, as exposed to user space.
Set the trap priority of packets trapped due to loopback error during
routing to the lowest priority. Such packets are not routed again by the
kernel and therefore should not mask other traps (e.g., host miss) that
should be routed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The policer is now initialized as part of the registration with devlink,
so there is no need to initialize it before the registration.
Remove the initialization.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register supported packet trap policers with devlink and implement
callbacks to change their parameters and read their counters.
Prevent user space from passing invalid policer parameters down to the
device by checking their validity and communicating the failure via an
appropriate extack message.
v2:
* Remove the max/min validity checks from __mlxsw_sp_trap_policer_set()
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare an array of policer IDs to register with devlink and their
associated parameters.
The array is composed from both policers that are currently bound to
exposed trap groups and policers that are not bound to any trap group.
v2:
* Provide max/min rate/burst size when registering policers
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization the driver configures various packet trap groups
and binds policers to them.
Currently, most of these groups are not exposed to user space and
therefore their policers should not be exposed as well. Otherwise, user
space will be able to alter policer parameters without knowing which
packet traps are policed by the policer.
Use a bitmap to track the used policer IDs so that these policers will
not be registered with devlink in a subsequent patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QoS Policer Configuration Register (QPCR) is used to configure
hardware policers. Extend this register with following fields and
defines which will be used by subsequent patches:
1. Violate counter: reads number of packets dropped by the policer
2. Clear counter: to ensure we start counting from 0
3. Rate and burst size limits
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dummy callback to set trap group parameters. Return an error when
the 'fail_trap_group_set' debugfs file is set in order to exercise error
paths and verify that error is propagated to user space when should.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet trap groups are used to aggregate logically related packet traps.
Currently, these groups allow user space to batch operations such as
setting the trap action of all member traps.
In order to prevent the CPU from being overwhelmed by too many trapped
packets, it is desirable to bind a packet trap policer to these groups.
For example, to limit all the packets that encountered an exception
during routing to 10Kpps.
Allow device drivers to bind default packet trap policers to packet trap
groups when the latter are registered with devlink.
The next patch will enable user space to change this default binding.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register three dummy packet trap policers with devlink and implement
callbacks to change their parameters and read their counters.
This will be used later on in the series to test the devlink-trap
policer infrastructure.
v2:
* Remove check about burst size being a power of 2 and instead add a
debugfs knob to fail the operation
* Provide max/min rate/burst size when registering policers and remove
the validity checks from nsim_dev_devlink_trap_policer_set()
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued user-access cleanups in the futex code.
- percpu-rwsem rewrite that uses its own waitqueue and atomic_t
instead of an embedded rwsem. This addresses a couple of
weaknesses, but the primary motivation was complications on the -rt
kernel.
- Introduce raw lock nesting detection on lockdep
(CONFIG_PROVE_RAW_LOCK_NESTING=y), document the raw_lock vs. normal
lock differences. This too originates from -rt.
- Reuse lockdep zapped chain_hlocks entries, to conserve RAM
footprint on distro-ish kernels running into the "BUG:
MAX_LOCKDEP_CHAIN_HLOCKS too low!" depletion of the lockdep
chain-entries pool.
- Misc cleanups, smaller fixes and enhancements - see the changelog
for details"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (55 commits)
fs/buffer: Make BH_Uptodate_Lock bit_spin_lock a regular spinlock_t
thermal/x86_pkg_temp: Make pkg_temp_lock a raw_spinlock_t
Documentation/locking/locktypes: Minor copy editor fixes
Documentation/locking/locktypes: Further clarifications and wordsmithing
m68knommu: Remove mm.h include from uaccess_no.h
x86: get rid of user_atomic_cmpxchg_inatomic()
generic arch_futex_atomic_op_inuser() doesn't need access_ok()
x86: don't reload after cmpxchg in unsafe_atomic_op2() loop
x86: convert arch_futex_atomic_op_inuser() to user_access_begin/user_access_end()
objtool: whitelist __sanitizer_cov_trace_switch()
[parisc, s390, sparc64] no need for access_ok() in futex handling
sh: no need of access_ok() in arch_futex_atomic_op_inuser()
futex: arch_futex_atomic_op_inuser() calling conventions change
completion: Use lockdep_assert_RT_in_threaded_ctx() in complete_all()
lockdep: Add posixtimer context tracing bits
lockdep: Annotate irq_work
lockdep: Add hrtimer context tracing bits
lockdep: Introduce wait-type checks
completion: Use simple wait queues
sched/swait: Prepare usage in completions
...
- Clean up and rework the PM QoS API to simplify the code and
reduce the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370
and similar platforms where the USB plug/unplug events are
handled by the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to
run on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate driver
and update its documentation (Rafael Wysocki, Alex Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file
and use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result (Leonard
Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level
PM QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences
in a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies).
-----BEGIN PGP SIGNATURE-----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=cBQd
-----END PGP SIGNATURE-----
Merge tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These clean up and rework the PM QoS API, address a suspend-to-idle
wakeup regression on some ACPI-based platforms, clean up and extend a
few cpuidle drivers, update multiple cpufreq drivers and cpufreq
documentation, and fix a number of issues in devfreq and several other
things all over.
Specifics:
- Clean up and rework the PM QoS API to simplify the code and reduce
the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370 and
similar platforms where the USB plug/unplug events are handled by
the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to run
on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate
driver and update its documentation (Rafael Wysocki, Alex
Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file and
use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result
(Leonard Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level PM
QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences in
a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies)"
* tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (78 commits)
cpufreq: intel_pstate: Simplify intel_pstate_cpu_init()
tools/power/x86/intel_pstate_tracer: fix a broken y-axis scale
ACPI: PM: s2idle: Refine active GPEs check
ACPICA: Allow acpi_any_gpe_status_set() to skip one GPE
PM: sleep: wakeup: Skip wakeup_source_sysfs_remove() if device is not there
PM / devfreq: Get rid of some doc warnings
PM / devfreq: Fix handling dev_pm_qos_remove_request result
PM / devfreq: Fix a typo in a comment
PM / devfreq: Change to DEVFREQ_GOV_UPDATE_INTERVAL event name
PM / devfreq: Remove unneeded extern keyword
PM / devfreq: Use constant name of userspace governor
ACPI: PM: s2idle: Fix comment in acpi_s2idle_prepare_late()
cpufreq: qcom: Add support for krait based socs
cpufreq: imx6q-cpufreq: Improve the logic of -EPROBE_DEFER handling
cpufreq: Use scnprintf() for avoiding potential buffer overflow
cpuidle: psci: Split psci_dt_cpu_init_idle()
PM / Domains: Allow no domain-idle-states DT property in genpd when parsing
PM / hibernate: Remove unnecessary compat ioctl overrides
PM: hibernate: fix docs for ioctls that return loff_t via pointer
Documentation: intel_pstate: update links for references
...
Add a separate set of PCS operations, which MAC drivers can use to
couple phylink with their associated MAC PCS layer. The PCS
operations include:
- pcs_get_state() - reads the link up/down, resolved speed, duplex
and pause from the PCS.
- pcs_config() - configures the PCS for the specified mode, PHY
interface type, and setting the advertisement.
- pcs_an_restart() - restarts 802.3 in-band negotiation with the
link partner
- pcs_link_up() - informs the PCS that link has come up, and the
parameters of the link. Link parameters are used to program the
PCS for fixed speed and non-inband modes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the bland 'ops' member of struct phylink to be a more
descriptive 'mac_ops' - this is necessary as we're about to introduce
another set of operations.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change phylink_mii_c22_pcs_set_advertisement() to take only the PHY
interface and advertisement mask, rather than the full phylink state.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out mapping the tx skb to a new function rtl8169_tx_map(). This
allows to remove redundancies, and rtl8169_get_txd_opts1() has only
one user left, so it can be inlined.
As a result rtl8169_xmit_frags() is significantly simplified, and in
rtl8169_start_xmit() the code is simplified and better readable.
No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qed_chain data structure was modified in
commit 1a4a69751f ("qed: Chain support for external PBL") to support
receiving an external pbl (due to iWARP FW requirements).
The pages pointed to by the pbl are allocated in qed_chain_alloc
and their virtual address are stored in an virtual addresses array to
enable accessing and freeing the data. The physical addresses however
weren't stored and were accessed directly from the external-pbl
during free.
Destroy-qp flow, leads to freeing the external pbl before the chain is
freed, when the chain is freed it tries accessing the already freed
external pbl, leading to a use-after-free. Therefore we need to store
the physical addresses in additional to the virtual addresses in a
new data structure.
Fixes: 1a4a69751f ("qed: Chain support for external PBL")
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Yuval Bason <ybason@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the mtu is greater than TD_MSS_MAX, then TSO is disabled, see
rtl8169_fix_features(). Because mss is less than mtu, we can't have
the case mss > TD_MSS_MAX in the TSO path.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds complete support for manipulating the L2 Policing Tables
from this switch. There are 45 table entries, one entry per each port
and traffic class, and one dedicated entry for broadcast traffic for
each ingress port.
Policing entries are shareable, and we use this functionality to support
shared block filters.
We are modeling broadcast policers as simple tc-flower matches on
dst_mac. As for the traffic class policers, the switch only deduces the
traffic class from the VLAN PCP field, so it makes sense to model this
as a tc-flower match on vlan_prio.
How to limit broadcast traffic coming from all front-panel ports to a
cumulated total of 10 Mbit/s:
tc qdisc add dev sw0p0 ingress_block 1 clsact
tc qdisc add dev sw0p1 ingress_block 1 clsact
tc qdisc add dev sw0p2 ingress_block 1 clsact
tc qdisc add dev sw0p3 ingress_block 1 clsact
tc filter add block 1 flower skip_sw dst_mac ff:ff:ff:ff:ff:ff \
action police rate 10mbit burst 64k
How to limit traffic with VLAN PCP 0 (also includes untagged traffic) to
100 Mbit/s on port 0 only:
tc filter add dev sw0p0 ingress protocol 802.1Q flower skip_sw \
vlan_prio 0 action police rate 100mbit burst 64k
The broadcast, VLAN PCP and port policers are compatible with one
another (can be installed at the same time on a port).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds partial configuration support for the L2 Policing Table. Out
of the 45 policing entries, only 5 are used (one for each port), in a
shared manner. All 8 traffic classes, and the broadcast policer, are
redirected to a common instance which belongs to the ingress port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a trivial passthrough towards the ocelot library, which
support port policers since commit 2c1d029a01 ("net: mscc: ocelot:
Implement port policers via tc command").
Some data structure conversion between the DSA core and the Ocelot
library is necessary, for policer parameters.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot has 384 policers that can be allocated to ingress ports,
QoS classes per port, and VCAP IS2 entries. ocelot_police.c
supports to set policers which can be allocated to police action
of VCAP IS2. We allocate policers from maximum pol_id, and
decrease the pol_id when add a new vcap_is2 entry which is
police action.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the FW RESET event comes to the driver from the firmware,
or the fw_status goes to 0 (stopped) or to 0xff (no PCI
connection), then shut down the driver activity. This event
signals a FW upgrade where we need to quiesce all operations and
wait for the FW to restart. The FW will continue the update
process once it sees all the LIFs are reset. When the update
process is done it will set the fw_status back to RUNNING.
Meanwhile, the heartbeat check continues and when the fw_status
is seen as set to running we can restart the driver operations.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link goes down, we need to disable the queues on the
NIC in addition to stopping the netdev stack. This lets the
FW know that the driver has stopped queue activity, and then
the FW can do internal reconfiguration work, whether actually
Link related, or for other internal FW needs. To do this,
we pull out the queue enable and disable from ionic_open()
and ionic_stop() so they can be used by other routines.
To help keep things sane, we swap the queue enables so that
the rx queue and its napi are enabled before the tx queue
which rides on the rx queues napi.
We also drop the ionic_lif_quiesce() as it doesn't do anything
more than what the queue disable has already taken care of.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the queue structures exist before trying
to delete them. This addresses a couple of error
recovery issues.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean out tx requests that didn't get finished before
shutting down the queue.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the irq request and free out of the qcq_init and deinit
and into the alloc and free routines where they belong for
better resource management.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the qcq debugfs add to the queue alloc, and likewise move
the debugfs delete to the queue free. The LIF debugfs add
also needs to be moved, but the del is already in the LIF free.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a link_status_check to the heartbeat watchdog.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange the link_up/link_down messages so that we announce
link up when we first notice that the link is up when the
driver loads, and decouple the link_up/link_down messages from
the UP and DOWN netdev state.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cited commit extended the enums 'hwtstamp_tx_types' and
'hwtstamp_rx_filters' with values that were not accounted for in the
switch statements, resulting in the build warnings below.
Fix by adding a default case.
drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c: In function ‘mlxsw_sp_ptp_get_message_types’:
drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c:915:2: warning: enumeration value ‘__HWTSTAMP_TX_CNT’ not handled in switch [-Wswitch]
915 | switch (tx_type) {
| ^~~~~~
drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c:927:2: warning: enumeration value ‘__HWTSTAMP_FILTER_CNT’ not handled in switch [-Wswitch]
927 | switch (rx_filter) {
| ^~~~~~
Fixes: f76510b458 ("ethtool: add timestamping related string sets")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When health reporter is registered to devlink, devlink will implicitly set
auto recover if and only if the reporter has a recover method. No reason
to explicitly get the auto recover flag from the driver.
Remove this flag from all drivers that called
devlink_health_reporter_create.
All existing health reporters set auto recovery to true if they have a
recover method.
Yet, administrator can unset auto recover via netlink command as prior to
this patch.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Health reporters should be registered with auto recover set to true.
Align dummy reporter behaviour with that, as in later patch the option to
set auto recover behaviour will be removed.
In addition, align netdevsim selftest to the new default value.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP Hardware Clock (PHC) subsystem offers an API for configuring
programmable pins. User space sets or gets the settings using ioctls,
and drivers verify dialed settings via a callback. Drivers may also
query pin settings by calling the ptp_find_pin() method.
Although the core subsystem protects concurrent access to the pin
settings, the implementation places illogical restrictions on how
drivers may call ptp_find_pin(). When enabling an auxiliary function
via the .enable(on=1) callback, drivers may invoke the pin finding
method, but when disabling with .enable(on=0) drivers are not
permitted to do so. With the exception of the mv88e6xxx, all of the
PHC drivers do respect this restriction, but still the locking pattern
is both confusing and unnecessary.
This patch changes the locking implementation to allow PHC drivers to
freely call ptp_find_pin() from their .enable() and .verify()
callbacks.
V2 ChangeLog:
- fixed spelling in the kernel doc
- add Vladimir's tested by tag
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may be up to the driver (in case ANY HW stats is passed) to select
which type of HW stats he is going to use. Add an infrastructure to
expose this information to user.
$ tc filter add dev enp3s0np1 ingress proto ip handle 1 pref 1 flower dst_ip 192.168.1.1 action drop
$ tc -s filter show dev enp3s0np1 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
dst_ip 192.168.1.1
in_hw in_hw_count 2
action order 1: gact action drop
random type none pass val 0
index 1 ref 1 bind 1 installed 10 sec used 10 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats immediate <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is not open, the service task which update the port
information per second is not running. In this case, the port
capabilities, including speed ability, autoneg ability, media type,
may be incorrect. Then get/set link ksetting may fail.
This patch fixes it by updating the port information before getting/
setting link ksettings when device is not open, and start timer
task immediately by setting delay time to 0 when device opens.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, VF's RSS configuration would be set to default
after VF reset, the the user's one will loss.
To fix it, this patch separates hclgevf_rss_init_hw() into
two parts, one sets up the default RSS configuration and
just be called when driver loading, one configures the hardware
and be called by driver loading or reset.
Fixes: d97b307213 ("net: hns3: Add RSS tuples support for VF")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the fraglist SKB headlen is larger than zero, current code
still handle the fraglist SKB linear data as frag data, which may
cause TX error.
This patch adds a new DESC_TYPE_FRAGLIST_SKB type to handle the
mapping and unmapping of the fraglist SKB linear data buffer.
Fixes: 8ae10cfb50 ("net: hns3: support tx-scatter-gather-fraglist feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/amazon/ena/ena_netdev.c:460:6: warning: symbol 'ena_xdp_exchange_program_rx_in_range' was not declared. Should it be static?
drivers/net/ethernet/amazon/ena/ena_netdev.c:481:6: warning: symbol 'ena_xdp_exchange_program' was not declared. Should it be static?
drivers/net/ethernet/amazon/ena/ena_netdev.c:1555:5: warning: symbol 'ena_xdp_handle_buff' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2065:5:
warning: symbol 'dpaa_a050385_wa' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for VLAN ID-based filtering by the MAC controller for MAC
drivers that support it. Only the 12-bit VID field is used.
Signed-off-by: Chuah Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a dev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mlx5e_rep_indr_setup_ft_cb to support indr block setup
in FT mode.
Both tc rules and flow table rules are of the same format,
It can re-use tc parsing for that, and move the flow table rules
to their steering domain(the specific chain_index), the indr
block offload in FT also follow this scenario.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Refactor indr setup block for support ft indr setup in the
next patch. The function mlx5e_rep_indr_offload exposes
'flags' in order set additional flag for FT in next patch.
Rename mlx5e_rep_indr_setup_tc_block to mlx5e_rep_indr_setup_block
and add flow_setup_cb_t callback parameters in order set the
specific callback for FT in next patch.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
eswitch_offloads_chains.{c,h} were just introduced this kernel release
cycle, eswitch is in high development demand right now and many
features are planned to be added to it. eswitch deserves its own
directory and here we move these new files to there, in preparation for
upcoming eswitch features and new files.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
In VF lag mode when remove the bonding module without bring down the
bond device first, we could potentially have circular dependency when we
unload IB devices and also handle fib events:
1. The bond work starts first;
2. The "modprobe -rv bonding" process tries to release the bond device,
with the "pernet_ops_rwsem" lock hold;
3. The bond work blocks in unregister_netdevice_notifier() and waits for
the lock because fib event came right before;
4. The kernel fib module tries to free all the fib entries by broadcasting
the "FIB_EVENT_NH_DEL" event;
5. Upon the fib event this lag_mp module holds the fib lock and queue a
fib work.
So:
bond work -> modprobe task -> kernel fib module -> lag_mp -> bond work
Today we either reload IB devices in roce lag in nic mode or either handle
fib events in switchdev mode, but a new feature could change that we'll
need to reload IB devices also in switchdev mode so this is a future proof
fix as one may not notice this later.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
mlx5: Remove uninitialized use of key in mlx5_core_create_mkey
{IB,net}/mlx5: Move asynchronous mkey creation to mlx5_ib
{IB,net}/mlx5: Assign mkey variant in mlx5_ib only
{IB,net}/mlx5: Setup mkey variant before mr create command invocation
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
A recent commit e893768179 ("devlink: prepare to support region
operations") used the region_cr_space_str and region_fw_health_str
variables as initializers for the devlink_region_ops structures.
This can result in compiler errors:
drivers/net/ethernet/mellanox//mlx4/crdump.c:45:10: error: initializer
element is not constant
.name = region_cr_space_str,
^
drivers/net/ethernet/mellanox//mlx4/crdump.c:45:10: note: (near
initialization for ‘region_cr_space_ops.name’)
drivers/net/ethernet/mellanox//mlx4/crdump.c:50:10: error: initializer
element is not constant
.name = region_fw_health_str,
The variables were made to be "const char * const", indicating that both
the pointer and data were constant. This was enough to resolve this on
recent GCC (gcc (GCC) 9.2.1 20190827 (Red Hat 9.2.1-1) for this author).
Unfortunately this is not enough for older compilers to realize that the
variable can be treated as a constant expression.
Fix this by introducing macros for the string and use those instead of
the variable name in the region ops structures.
Reported-by: tanhuazhong <tanhuazhong@huawei.com>
Fixes: e893768179 ("devlink: prepare to support region operations")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the mt7530 switch driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().
Signed-off-by: René van Dorst <opensource@vdorst.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the P/Q/R/S series supports some more counters,
generically named "Ethernet statistics counter", which we were not
printing. Add them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling queue_delayed_work concurrently with
destroy_workqueue might race to an unexpected outcome -
scheduled task after wq is destroyed or other resources
(like ptt_pool) are freed (yields NULL pointer dereference).
cancel_delayed_work prevents the race by cancelling
the timer triggered for scheduling a new task.
Fixes: 59ccf86fe ("qed: Add driver infrastucture for handling mfw requests")
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Yuval Basson <ybason@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9131 provides DLL controlled delays on RXC and TXC lines. This
patch makes use of those delays. The information which delays should
be enabled or disabled comes from the interface names, documented in
ethernet-controller.yaml:
rgmii: Disable RXC and TXC delays
rgmii-id: Enable RXC and TXC delays
rgmii-txid: Enable only TXC delay, disable RXC delay
rgmii-rxid: Enable onlx RXC delay, disable TXC delay
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new netlink attribute to allow a user to (optionally)
specify the desired offload mode immediately upon MACSec link creation.
Separate iproute patch will be required to support this from user space.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the big recipe into 3 stages: compile, link, and hexdump.
After this commit, the build log with CONFIG_WANXL_BUILD_FIRMWARE
will look like this:
M68KAS drivers/net/wan/wanxlfw.o
M68KLD drivers/net/wan/wanxlfw.bin
BLDFW drivers/net/wan/wanxlfw.inc
CC [M] drivers/net/wan/wanxl.o
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The firmware source, wanxlfw.S, is currently compiled by the combo of
$(CPP) and $(M68KAS). This is not what we usually do for compiling *.S
files. In fact, this Makefile is the only user of $(AS) in the kernel
build.
Instead of combining $(CPP) and (AS) from different tool sets, using
$(M68KCC) as an assembler driver is simpler, and saner.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
YueHaibing