Commit Graph

378 Commits

Author SHA1 Message Date
Jiri Pirko e5e2a8fd83 bonding: wipe out printk's
I did not introduce new lines over 80 chars. I even eliminated some of
them.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-13 16:43:32 -07:00
David S. Miller da8120355e Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/wireless/orinoco/main.c
2009-07-16 20:21:24 -07:00
Moni Shoua e36b9d16c6 bonding: clean muticast addresses when device changes type
Bonding device forbids slave device of different types under the same
master.

However, it is possible for a bonding master to change type during its
lifetime.  This can be either from ARPHRD_ETHER to ARPHRD_INFINIBAND
or the other way arround.  The change of type requires device level
multicast address cleanup because device level multicast addresses
depend on the device type.

The patch adds a call to dev_close() before the bonding master changes
type and dev_open() just after that.

In the example below I enslaved an IPoIB device (ib0) under
bond0. Since each bonding master starts as device of type ARPHRD_ETHER
by default, a change of type occurs when ib0 is enslaved.

This is how /proc/net/dev_mcast looks like without the patch

5    bond0           1     0     00ffffffff12601bffff000000000001ff96ca05
5    bond0           1     0     01005e000116
5    bond0           1     0     01005e7ffffd
5    bond0           1     0     01005e000001
5    bond0           1     0     333300000001
6    ib0             1     0     00ffffffff12601bffff000000000001ff96ca05
6    ib0             1     0     333300000001
6    ib0             1     0     01005e000001
6    ib0             1     0     01005e7ffffd
6    ib0             1     0     01005e000116
6    ib0             1     0     00ffffffff12401bffff00000000000000000001
6    ib0             1     0     00ffffffff12601bffff00000000000000000001

and this is how it looks like after the patch.

5    bond0           1     0     00ffffffff12601bffff000000000001ff96ca05
5    bond0           1     0     00ffffffff12601bffff00000000000000000001
5    bond0           1     0     00ffffffff12401bffff0000000000000ffffffd
5    bond0           1     0     00ffffffff12401bffff00000000000000000116
5    bond0           1     0     00ffffffff12401bffff00000000000000000001
6    ib0             1     0     00ffffffff12601bffff000000000001ff96ca05
6    ib0             1     0     00ffffffff12401bffff00000000000000000116
6    ib0             1     0     00ffffffff12401bffff0000000000000ffffffd
6    ib0             2     0     00ffffffff12401bffff00000000000000000001
6    ib0             2     0     00ffffffff12601bffff00000000000000000001

Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-16 18:05:23 -07:00
Julia Lawall 8e321c4f72 drivers/net/bonding: Adjust constant name
AD_SHORT_TIMEOUT and AD_STATE_LACP_ACTIVITY have the same value, but
AD_STATE_LACP_ACTIVITY better reflects the intended semantics.

[ J adds: AD_STATE_LACP_ACTIVITY is a value defined by the standard, and
should be set here in accordance with 802.3ad 43.4.12; AD_SHORT_TIMEOUT
is a constant specific to the Linux 802.3ad implementation that happens
to have the same value ]

The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
struct port_params p;
@@
* p.port_state |= AD_SHORT_TIMEOUT
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-12 20:11:32 -07:00
Patrick McHardy ec634fe328 net: convert remaining non-symbolic return values in ndo_start_xmit() functions
This patch converts the remaining occurences of raw return values to their
symbolic counterparts in ndo_start_xmit() functions that were missed by the
previous automatic conversion.

Additionally code that assumed the symbolic value of NETDEV_TX_OK to be zero
is changed to explicitly use NETDEV_TX_OK.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05 19:23:38 -07:00
Stephen Hemminger 181470fcf3 bonding: initialization rework
Need to rework how bonding devices are initialized to make it more
amenable to creating bonding devices via netlink.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-13 23:29:04 -07:00
Stephen Hemminger 5c5129b54f bonding: use is_zero_ether_addr
Remove bogus non-portable possibly unaligned way of testing
for zero addres..

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-13 23:29:03 -07:00
Stephen Hemminger 373500db92 bonding: network device names are case sensative
The bonding device acts unlike all other Linux network device functions
in that it ignores case of device names. The developer must have come
from windows!

Cleanup the management of names and use standard routines where possible.
Flag places where bonding device still doesn't work right with network
namespaces.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-13 23:29:01 -07:00
Stephen Hemminger 6d7ab43ccc bonding: elminate bad refcount code
The "expected_refcount" stuff in bonding sysfs module is a mistake.
Sysfs does proper refcounting, and it is okay to remove a bond device
that has some user process holding the file open.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-13 23:29:00 -07:00
Stephen Hemminger 3d632c3f28 bonding: fix style issues
Resolve some of the complaints from checkpatch, and remove "magic emacs format"
comments, and useless MODULE_SUPPORTED_DEVICE(). But should not
change actual code.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-13 23:28:57 -07:00
Stephen Hemminger 9e71626c1c bonding: fix destructor
It is not safe to use a network device destructor that is a function in
the module, since it can be called after module is unloaded if sysfs
handle is open.

When eventually using netlink, the device cleanup code needs to be done
via uninit function.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-13 23:28:56 -07:00
Stephen Hemminger 7e08384045 bonding: remove bonding read/write semaphore
The whole read/write semaphore locking can be removed. It doesn't add any
protection that isn't already done by using the RTNL mutex properly.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-13 23:28:54 -07:00
Stephen Hemminger d93216051a bonding: initialize before registration
Avoid a unnecessary carrier state transistion that happens when device
is registered.
Lockdep works better if initialization is done before registration as well.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-13 23:28:52 -07:00
Stephen Hemminger d2991f7535 bonding: bond_create always called with default parameters
bond_create() is always called with same parameters so move the argument
down.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-13 23:28:51 -07:00
Stephen Hemminger 130aa61a77 bonding: fix multiple module load problem
Some users still load bond module multiple times to create bonding
devices.  This accidentally was broken by a later patch about
the time sysfs was fixed.  According to Jay, it was broken
by:
   commit b8a9787edd
   Author: Jay Vosburgh <fubar@us.ibm.com>
   Date:   Fri Jun 13 18:12:04 2008 -0700

     bonding: Allow setting max_bonds to zero

Note: sysfs and procfs still produce WARN() messages when this is done
so the sysfs method is the recommended API.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-11 05:46:04 -07:00
Jiri Pirko ae63e808f5 bonding: use bond_is_lb() when it's appropriate
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-29 22:08:31 -07:00
Eric Dumazet 93f154b594 net: release dst entry in dev_hard_start_xmit()
One point of contention in high network loads is the dst_release() performed
when a transmited skb is freed. This is because NIC tx completion calls
dev_kree_skb() long after original call to dev_queue_xmit(skb).

CPU cache is cold and the atomic op in dst_release() stalls. On SMP, this is
quite visible if one CPU is 100% handling softirqs for a network device,
since dst_clone() is done by other cpus, involving cache line ping pongs.

It seems right place to release dst is in dev_hard_start_xmit(), for most
devices but ones that are virtual, and some exceptions.

David Miller suggested to define a new device flag, set in alloc_netdev_mq()
(so that most devices set it at init time), and carefuly unset in devices
which dont want a NULL skb->dst in their ndo_start_xmit().

List of devices that must clear this flag is :

- loopback device, because it calls netif_rx() and quoting Patrick :
    "ip_route_input() doesn't accept loopback addresses, so loopback packets
     already need to have a dst_entry attached."
- appletalk/ipddp.c : needs skb->dst in its xmit function

- And all devices that call again dev_queue_xmit() from their xmit function
(as some classifiers need skb->dst) : bonding, vlan, macvlan, eql, ifb, hdlc_fr

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-18 22:19:19 -07:00
Eric W. Biederman 496a60cdcd net: FIX bonding sysfs rtnl_lock deadlock
Sysfs files for a network device can not unconditionally take the
rtnl_lock as the bonding sysfs files do.  If someone accesses those
sysfs files while the network device is being unregistered with the
rtnl_lock held we will deadlock.

So use trylock and restart_syscall to avoid this problem.

Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-18 22:16:00 -07:00
David S. Miller bb803cfbec Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/scsi/fcoe/fcoe.c
2009-05-18 21:08:20 -07:00
Stephen Hemminger 4cd6fe1c64 bonding: fix link down handling in 802.3ad mode
One of the purposes of bonding is to allow for redundant links, and failover
correctly if the cable is pulled. If all the members of a bonded device have
no carrier present, the bonded device itself needs to report no carrier present
to user space so management tools (like routing daemons) can respond.

Bonding in 802.3ad mode does not work correctly for this because it incorrectly
chooses a link that is down as a possible aggregator.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 21:15:54 -07:00
Eric Dumazet 9d21493b4b net: tx scalability works : trans_start
struct net_device trans_start field is a hot spot on SMP and high performance
devices, particularly multi queues ones, because every transmitter dirties
it. Is main use is tx watchdog and bonding alive checks.

But as most devices dont use NETIF_F_LLTX, we have to lock
a netdev_queue before calling their ndo_start_xmit(). So it makes
sense to move trans_start from net_device to netdev_queue. Its update
will occur on a already present (and in exclusive state) cache line, for
free.

We can do this transition smoothly. An old driver continue to
update dev->trans_start, while an updated one updates txq->trans_start.

Further patches could also put tx_bytes/tx_packets counters in 
netdev_queue to avoid dirtying dev->stats (vlan device comes to mind)

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 20:55:16 -07:00
Jiri Pirko 3a6d54c563 net: remove needless (now buggy) & from dev->dev_addr
Patch fixes issues with dev->dev_addr changing from array to pointer.
Hopefully there are no others.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 11:59:47 -07:00
Florian Westphal 9d34d1a20e bonding: fix panic if initialization fails
If module initialisation failed (e.g. because the bonding sysfs entry
cannot be created), kernel panics:
 IP: [<ffffffff8024910a>] destroy_workqueue+0x2d/0x146
Call Trace:
 [<ffffffff808268c4>] bond_destructor+0x28/0x78
 [<ffffffff80b64471>] netdev_run_todo+0x231/0x25a
 [<ffffffff80b6dbcd>] rtnl_unlock+0x9/0xb
 [<ffffffff81567907>] bonding_init+0x83e/0x84a

Remove the calls to bond_work_cancel_all() and destroy_workqueue();
both are also called/scheduled via bond_free_all().

bond_destroy_sysfs is unecessary because the sysfs entry has
not been created in the error case.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-09 13:19:47 -07:00
Richard Genoud ed9b58bc44 Remove duplicate slow protocol define in bond_3ad.h
ETH_P_SLOW is already defined in include/linux/if_ether.h.
There's no need to define BOND_ETH_P_LACPDU in drivers/net/bonding/bond_3ad.h

Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-09 13:15:49 -07:00
David S. Miller 22f6dacdfc Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	include/net/tcp.h
2009-05-08 02:48:30 -07:00
Jiri Pirko aee64faf23 bonding: get rid of CONFIG_PROC_FS ifdefs
Remove CONFIG_PROC_FS ifdefs from the code by adding void functions.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>

 drivers/net/bonding/bond_main.c |   30 ++++++++++++++++++++----------
 1 files changed, 20 insertions(+), 10 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-05 12:26:25 -07:00
Jay Vosburgh 815bcc2719 bonding: fix alb mode locking regression
Fix locking issue in alb MAC address management; removed
incorrect locking and replaced with correct locking.  This bug was
introduced in commit 059fe7a578
("bonding: Convert locks to _bh, rework alb locking for new locking")

	Bug reported by Paul Smith <paul@mad-scientist.net>, who also
tested the fix.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-04 21:28:10 -07:00
David S. Miller d252a5e7b7 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 2009-05-03 14:07:43 -07:00
Jiri Pirko 1363d9b135 bonding: correct the cleanup in bond_create()
This patch makes the cleanup in bond_create nicer :) Also now the forgotten
free_netdev is called.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-01 15:35:28 -07:00
Eric Dumazet 689c96cca7 bonding: bond_slave_info_query() fix
bond_slave_info_query() should keep a read lock while accessing slave info,
or risk accessing stale data and corruption.

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-01 15:18:19 -07:00
Jiri Pirko 41f8910040 bonding: ignore updelay param when there is no active slave
Pointed out by Sean E. Millichamp.

Quote from Documentation/networking/bonding.txt:
"Note that when a bonding interface has no active links, the
driver will immediately reuse the first link that goes up, even if the
updelay parameter has been specified (the updelay is ignored in this
case).  If there are slave interfaces waiting for the updelay timeout
to expire, the interface that first went into that state will be
immediately reused.  This reduces down time of the network if the
value of updelay has been overestimated, and since this occurs only in
cases with no connectivity, there is no additional penalty for
ignoring the updelay."

This patch actually changes the behaviour in this way.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>

 drivers/net/bonding/bond_main.c |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-27 02:57:44 -07:00
Jiri Pirko 29112f4e24 bonding: use ethtool for link checking first
This patch only changes the order of interfaces to use for checking slave link
status in bond_check_dev_link() to priorize ethtool interface. Should safe some
troubles as ethtool seems to be more supported.

Jirka

Signed-off-by: Jiri Pirko <jpirko@redhat.com>

 drivers/net/bonding/bond_main.c |   26 ++++++++++++--------------
 1 files changed, 12 insertions(+), 14 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-27 02:57:44 -07:00
Jay Vosburgh 2690f8d62e bonding: Remove debug printk
Remove debug printk I accidently left in as part of commit:

commit 6146b1a4da
Author: Jay Vosburgh <fubar@us.ibm.com>
Date:   Tue Nov 4 17:51:15 2008 -0800

    bonding: Fix ALB mode to balance traffic on VLANs

	Reported by Duncan Gibb <duncan.gibb@siriusit.co.uk>

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-14 16:53:14 -07:00
Brian Haley 5a31bec014 Bonding: fix zero address hole bug in arp_ip_target list
Fix a zero address hole bug in the bonding arp_ip_target list
that was causing the bond to ignore ARP replies (bugz 13006).
Instead of just setting the array entry to zero, we now
copy any additional entries down one slot, putting the
zero entry at the end.  With this change we can now have
all the loops that walk the array stop when they hit a zero
since there will be no addresses after it.

Changes are based in part on code fragment provided in kernel:
bugzilla 13006:

	http://bugzilla.kernel.org/show_bug.cgi?id=13006

by Steve Howard <steve@astutenetworks.com>

Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-13 00:12:41 -07:00
Alexey Dobriyan 99b7623380 proc 2/2: remove struct proc_dir_entry::owner
Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.

We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.

But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.

->read_proc/->write_proc were just fixed to not require ->owner for
protection.

rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.

Removing ->owner will also make PDE smaller.

So, let's nuke it.

Kudos to Jeff Layton for reminding about this, let's say, oversight.

http://bugzilla.kernel.org/show_bug.cgi?id=12454

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
2009-03-31 01:14:44 +04:00
Jiri Pirko 5a29f7893f bonding: select current active slave when enslaving device for mode tlb and alb
I've hit an issue on my system when I've been using RealTek RTL8139D cards in
bonding interface in mode balancing-alb. When I enslave a card, the current
active slave (bond->curr_active_slave) is not set and the link is therefore
not functional.

----
# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008)

Bonding Mode: adaptive load balancing
Primary Slave: None
Currently Active Slave: None
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0

Slave Interface: eth1
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:1f:1f:01:2f:22
----

The thing that gets it right is when I unplug the cable and then I put it back
into the NIC. Then the current active slave is set to eth1 and link is working
just fine. Here is dmesg log with bonding DEBUG messages turned on:
----
ADDRCONF(NETDEV_UP): bond0: link is not ready
event_dev: bond0, event: 1
IFF_MASTER
event_dev: bond0, event: 8
IFF_MASTER
bond_ioctl: master=bond0, cmd=35216
slave_dev=cac5d800: 
slave_dev->name=eth1: 
eth1: ! NETIF_F_VLAN_CHALLENGED
event_dev: eth1, event: 8
eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
event_dev: eth1, event: 1
event_dev: eth1, event: 8
IFF_SLAVE
Initial state of slave_dev is BOND_LINK_UP
bonding: bond0: enslaving eth1 as an active interface with an up link.
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
event_dev: bond0, event: 4
IFF_MASTER
bond0: no IPv6 routers present

<<<<cable unplug>>>>

eth1: link down
event_dev: eth1, event: 4
IFF_SLAVE
bonding: bond0: link status definitely down for interface eth1, disabling it
event_dev: bond0, event: 4
IFF_MASTER

<<<<cable plug>>>>

eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
event_dev: eth1, event: 4
IFF_SLAVE
bonding: bond0: link status definitely up for interface eth1.
bonding: bond0: making interface eth1 the new active one.
event_dev: eth1, event: 8
IFF_SLAVE
event_dev: eth1, event: 8
IFF_SLAVE
bonding: bond0: first active interface up!
event_dev: bond0, event: 4
IFF_MASTER
----

The current active slave is set by calling bond_select_active_slave() function
from bond_miimon_commit() function when the slave (eth1) link goes to state up.

I also tested this on other machine with Broadcom NetXtreme II BCM5708
1000Base-T NIC and there all works fine. The thing is that this adapter is down
and goes up after few seconds after it is enslaved.

This patch calls bond_select_active_slave() in bond_enslave() function for modes
alb and tlb and makes sure that the current active slave is set up properly even
when the slave state is already up. Tested on both systems, works fine.

Notice: The same problem can maybe also occrur in mode 8023AD but I'm unable to
test that.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-25 17:23:38 -07:00
David S. Miller 2b1c4354de Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/virtio_net.c
2009-03-20 02:27:41 -07:00
Jay Vosburgh 17d04500e2 bonding: Fix updating of speed/duplex changes
This patch corrects an omission from the following commit:

commit f0c76d6177
Author: Jay Vosburgh <fubar@us.ibm.com>
Date:   Wed Jul 2 18:21:58 2008 -0700

    bonding: refactor mii monitor

	The un-refactored code checked the link speed and duplex of
every slave on every pass; the refactored code did not do so.

	The 802.3ad and balance-alb/tlb modes utilize the speed and
duplex information, and require it to be kept up to date.  This patch
adds a notifier check to perform the appropriate updating when the slave
device speed changes.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18 18:38:25 -07:00
David S. Miller 508827ff0a Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/tokenring/tmspci.c
	drivers/net/ucc_geth_mii.c
2009-03-05 02:06:47 -08:00
Patrick McHardy 72e2240f18 bonding: Fix device passed into ->ndo_neigh_setup().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-05 01:57:44 -08:00
Hannes Eder 54b87323ed drivers/net/bonding: fix sparse warning: symbol shadows an earlier one
Impact: Rename function scope variable.

Fix this sparse warning:
  drivers/net/bonding/bond_main.c:4704:13: warning: symbol 'mode' shadows an earlier one
  drivers/net/bonding/bond_main.c:95:13: originally declared here

Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-17 17:26:08 -08:00
Hannes Eder 1f78d9f945 drivers/net/bonding: fix sparse warnings: context imbalance
Impact: Attribute functions with __acquires(...) and/or __releases(...).

Fix this sparse warnings:
  drivers/net/bonding/bond_alb.c:1675:9: warning: context imbalance in 'bond_alb_handle_active_change' - unexpected unlock
  drivers/net/bonding/bond_alb.c:1742:9: warning: context imbalance in 'bond_alb_set_mac_address' - unexpected unlock
  drivers/net/bonding/bond_main.c:1025:17: warning: context imbalance in 'bond_do_fail_over_mac' - unexpected unlock
  drivers/net/bonding/bond_main.c:3195:13: warning: context imbalance in 'bond_info_seq_start' - wrong count at exit
  drivers/net/bonding/bond_main.c:3234:13: warning: context imbalance in 'bond_info_seq_stop' - unexpected unlock

Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-17 17:26:08 -08:00
Harvey Harrison 09640e6365 net: replace uses of __constant_{endian}
Base versions handle constant folding now.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-01 00:45:17 -08:00
Jan Engelhardt 4101dec9ca net: constify VFTs
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-21 14:03:37 -08:00
Stephen Hemminger 53a3294e26 bonding: use net_device_ops
Use the correct pointer in debug message.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-06 10:41:56 -08:00
Holger Eitzenberger e727149e26 802.3ad: use standard ethhdr instead of ad_header
802.3ad has its own ethhdr-like structure in the form of an ad_header,
which is at the start of both the LACPDU and marker PDU.  Both are
the same from the struct values, both are packed as well.

It's therefore perfectly fine to replace the ad_header by the ethhdr
and to remove its definition.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26 13:41:53 -08:00
Holger Eitzenberger e4ac43200f 802.3ad: generalize out mac address initializer
Generalize out mac address initializer for the LACPDU multicast
address and use in two places.  Remove the now unused
AD_MULTICAST_LACPDU_ADDR.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26 13:40:48 -08:00
Holger Eitzenberger 7addeef6b1 802.3ad: initialize ports LACPDU from const initializer
Save some text by initializing ports LACPDU from const initializer,
then get rid of ad_initialize_lacpdu().

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26 13:28:33 -08:00
Holger Eitzenberger 87f422f861 802.3ad: remove typedef around ad_system
As typedefs are considered a bad thing most of the time remove the
typedef around ad_system.

Signed-off-by: Holger Eitzenberger <heitzenberger@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26 13:27:57 -08:00
Holger Eitzenberger 1624db7be0 802.3ad: turn ports is_individual into a bool
Turn ports is_individual into a bool.  There is no functional change.

Signed-off-by: Holger Eitzenberger <heitzenberger@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26 13:27:21 -08:00
Holger Eitzenberger f48127b6f3 802.3ad: turn ports is_enabled into a bool
Turn ports is_enabled into a bool.  There is no functional change.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26 13:26:54 -08:00
Holger Eitzenberger d238d458a7 802.3ad: make ntt bool
Turn Need-To-Transmit port variable into a bool.  There is no
functional change.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26 11:18:15 -08:00
Hannes Eder b06715b7a3 drivers/net/bonding: fix sparse warnings: move decls to header file
Fix this sparse warnings:

  drivers/net/bonding/bond_main.c:104:20: warning: symbol 'bonding_defaults' was not declared. Should it be static?
  drivers/net/bonding/bond_main.c:204:22: warning: symbol 'ad_select_tbl' was not declared. Should it be static?
  drivers/net/bonding/bond_sysfs.c:60:21: warning: symbol 'bonding_rwsem' was not declared. Should it be static?

Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25 23:58:57 -08:00
Holger Eitzenberger 3b5b35d022 bonding: use port_params in __update_lacpdu_from_port
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17 19:13:53 -08:00
Holger Eitzenberger 3c52065fbb bonding: use port_params in __update_default_selected()
I also removed some of the unneeded braces in the if condition to
improve readability and a little bit of reformatting.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17 19:13:27 -08:00
Holger Eitzenberger ce6a49ad40 bonding: use port_params in __update_selected()
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17 19:13:07 -08:00
Holger Eitzenberger a6ae186b9a bonding: remove various function declarations
They are all defined before used, it's therefore ok to remove
them.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17 19:12:40 -08:00
Holger Eitzenberger c7e703d01e bonding: init port_params from template
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17 19:12:07 -08:00
Holger Eitzenberger 5eefd1adce bonding: use plain memcpy in __record_default()
Also remove the pointless comment at the top.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17 19:08:46 -08:00
Holger Eitzenberger b99d6ba96d bonding: use port_params in __record_pdu()
It helps in maintaining the various partner information values from
the LACPDU.  It also removes the pointless comment at the top.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17 19:08:14 -08:00
Holger Eitzenberger 1055c9aba3 bonding: introduce and use port_params structure
It generally helps to handle those values in various places, using it
might make the code more readable and gives room for other improvements.

The IEEE standard talks about them as "parameter values".

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17 19:07:38 -08:00
Holger Eitzenberger aa3128199d bonding: improve elaborate port_state assignment
The previous code was just a funny way of assigning both values (they
are both of type u8).

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17 19:07:16 -08:00
Holger Eitzenberger e97fd7c6d5 bonding: turn all bond_parm_tbls const
Turn all bond_parm_tbls const.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09 23:10:38 -08:00
Holger Eitzenberger 325dcf7a90 bonding: make tbl argument to bond_parse_parm() const
bond_parse_parm() parses a parameter table for a particular value and
is therefore not modifying the table at all.  Therefore make the 2nd
argument const, thus allowing to make the tables const later.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09 23:10:17 -08:00
Holger Eitzenberger d78755237f bonding: remove duplicate declarations
Remove some declarations from bonding.c as they are declared in bonding.h
already.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09 23:09:49 -08:00
Holger Eitzenberger 5a03cdb7f2 bonding: use pr_debug instead of own macros
Use pr_debug() instead of own macros.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09 23:09:22 -08:00
Holger Eitzenberger ef65583d01 bonding: fix compile error if debug enabled
This is what I get if debug is enabled:

drivers/net/bonding/bond_ipv6.c: In function 'bond_na_send':
drivers/net/bonding/bond_ipv6.c:75: error: 'slave' undeclared (first use in this function)
drivers/net/bonding/bond_ipv6.c:75: error: (Each undeclared identifier is reported only once
drivers/net/bonding/bond_ipv6.c:75: error: for each function it appears in.)

This patch fixes that.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09 23:08:55 -08:00
Holger Eitzenberger 77afc92b79 bonding: use table for mode names
Use a small array in bond_mode_name() for the names, thus saving some
space:

before

    text     data      bss      dec    hex filename
   57736     9372      344    67452  1077c drivers/net/bonding/bonding.ko

after
    text     data      bss      dec    hex filename
   57441     9372      344    67157  10655 drivers/net/bonding/bonding.ko

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09 23:08:09 -08:00
Holger Eitzenberger 5840205426 bonding: add and use bond_is_lb()
Introduce and use bond_is_lb(), it is usefull to shorten the repetitive
check for either ALB or TLB mode.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09 23:07:13 -08:00
Wang Chen 244ef9b917 bond: Kill directly reference of netdev->priv
Simply replace netdev->priv with netdev_priv().

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-03 21:14:04 -08:00
Stephen Hemminger 008298231a netdev: add more functions to netdevice ops
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.

Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 20:14:53 -08:00
Stephen Hemminger eb7cc59a03 bonding: convert to net_device_ops
Convert to net_device_ops table.
Note: for some operations move error checking into generic networking
layer (rather than looking at pointers in bonding).

A couple of gratituous style cleanups to get rid of extra {}

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-19 22:42:42 -08:00
Stephen Hemminger eeda3fd64f netdev: introduce dev_get_stats()
In order for the network device ops get_stats call to be immutable, the handling
of the default internal network device stats block has to be changed. Add a new
helper function which replaces the old use of internal_get_stats.

Note: change return code to make it clear that the caller should not
go changing the returned statistics.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-19 21:40:23 -08:00
Wang Chen 454d7c9b14 netdevice: safe convert to netdev_priv() #part-1
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
   netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.

This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-12 23:37:49 -08:00
Jay Vosburgh fd989c8332 bonding: alternate agg selection policies for 802.3ad
This patch implements alternative aggregator selection policies
for 802.3ad.  The existing policy, now termed "stable," selects the active
aggregator by greatest bandwidth, and only reselects a new aggregator
if the active aggregator is entirely disabled (no more ports or all ports
down).

	This patch adds two new policies: bandwidth and count, selecting
the active aggregator by total bandwidth (like the stable policy) or by
the number of ports in the aggregator, respectively.  These two policies
also differ from the stable policy in that they will reselect the active
aggregator when availability-related changes occur in the bond (e.g.,
link state change).

	This permits "gang failover" within 802.3ad, allowing redundant
aggregators along parallel paths to always maintain the "best" aggregator
as the active aggregator (rather than having to wait for the active to
entirely fail).

	This patch also updates the driver version to 3.5.0.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-06 00:49:47 -05:00
Jay Vosburgh 6146b1a4da bonding: Fix ALB mode to balance traffic on VLANs
The current ALB function that processes incoming ARPs
does not handle traffic for VLANs configured above bonding.  This causes
traffic on those VLANs to all be assigned the same slave.  This patch
corrects that misbehavior by locating the bonding interface nested below
the VLAN interface.

	Bug reported by Sven Anders <anders@anduras.de>, who also
tested an earlier version of this patch and confirmed that it resolved
the problem.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-06 00:49:40 -05:00
Brian Haley 305d552acc bonding: send IPv6 neighbor advertisement on failover
This patch adds better IPv6 failover support for bonding devices,
especially when in active-backup mode and there are only IPv6 addresses
configured, as reported by Alex Sidorenko.

- Creates a new file, net/drivers/bonding/bond_ipv6.c, for the
   IPv6-specific routines.  Both regular bonds and VLANs over bonds
   are supported.

- Adds a new tunable, num_unsol_na, to limit the number of unsolicited
   IPv6 Neighbor Advertisements that are sent on a failover event.
   Default is 1.

- Creates two new IPv6 neighbor discovery functions:

   ndisc_build_skb()
   ndisc_send_skb()

   These were required to support VLANs since we have to be able to
   add the VLAN id to the skb since ndisc_send_na() and friends
   shouldn't be asked to do this.  These two routines are basically
   __ndisc_send() split into two pieces, in a slightly different order.

- Updates Documentation/networking/bonding.txt and bumps the rev of bond
   support to 3.4.0.

On failover, this new code will generate one packet:

- An unsolicited IPv6 Neighbor Advertisement, which helps the switch
   learn that the address has moved to the new slave.

Testing has shown that sending just the NA results in pretty good
behavior when in active-back mode, I saw no lost ping packets for example.

Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-06 00:49:37 -05:00
Jay Vosburgh 6cf3f41e6c bonding, net: Move last_rx update into bonding recv logic
The only user of the net_device->last_rx field is bonding.
This patch adds a conditional update of last_rx to the bonding special
logic in skb_bond_should_drop, causing last_rx to only be updated when
the ARP monitor is running.

	This frees network device drivers from the necessity of
updating last_rx, which can have cache line thrash issues.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 18:16:50 -08:00
Harvey Harrison 63779436ab drivers: replace NIPQUAD()
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31 00:56:00 -07:00
David S. Miller a1744d3bee Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	drivers/net/wireless/p54/p54common.c
2008-10-31 00:17:34 -07:00
Andy Gospodarek ce39a800ea bonding: fix panic when taking bond interface down before removing module
A panic was discovered with bonding when using mode 5 or 6 and trying to
remove the slaves from the bond after the interface was taken down.
When calling 'ifconfig bond0 down' the following happens:

    bond_close()
        bond_alb_deinitialize()
            tlb_deinitialize()
		kfree(bond_info->tx_hashtbl)
                bond_info->tx_hashtbl = NULL

Unfortunately if there are still slaves in the bond, when removing the
module the following happens:

    bonding_exit()
        bond_free_all()
            bond_release_all()
                bond_alb_deinit_slave()
                    tlb_clear_slave()
                        tx_hash_table = BOND_ALB_INFO(bond).tx_hashtbl
			u32 next_index = tx_hash_table[index].next

As you might guess we panic when trying to access a few entries into the
table that no longer exists.

I experimented with several options (like moving the calls to
tlb_deinitialize somewhere else), but it really makes the most sense to
be part of the bond_close routine.  It also didn't seem logical move
tlb_clear_slave around too much, so the simplest option seems to add a
check in tlb_clear_slave to make sure we haven't already wiped the
tx_hashtbl away before searching for all the non-existent hash-table
entries that used to point to the slave as the output interface.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31 00:46:12 -04:00
Jay Vosburgh a434e43f3d bonding: Clean up resource leaks
This patch reworks the resource free logic performed at the time
a bonding device is released.  This (a) closes two resource leaks, one
for workqueues and one for multicast lists, and (b) improves commonality
of code between the "destroy one" and "destroy all" paths by performing
final free activity via destructor instead of explicitly (and differently)
in each path.

"Sean E. Millichamp" <sean@bruenor.org> reported the workqueue
leak, and included a different patch.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31 00:46:04 -04:00
Jay Vosburgh fba4acda35 bonding: fix miimon failure counter
During the rework of the mii monitor for:

  commit f0c76d6177
  Author: Jay Vosburgh <fubar@us.ibm.com>
  Date:   Wed Jul 2 18:21:58 2008 -0700

    bonding: refactor mii monitor

I left out the increment of the link failure counter.  This
patch corrects that omission.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31 00:45:51 -04:00
Harvey Harrison 8cf14e3837 net: easy removals of HIPQUAD using %pI4 format
As a bonus, removes some unnecessary byteswapping.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-29 22:43:33 -07:00
Johannes Berg e174961ca1 net: convert print_mac to %pM
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.

I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-27 17:06:18 -07:00
Herbert Xu b63365a2d6 net: Fix disjunct computation of netdev features
My change

    commit e2a6b85247
    net: Enable TSO if supported by at least one device

didn't do what was intended because the netdev_compute_features
function was designed for conjunctions.  So what happened was that
it would simply take the TSO status of the last constituent device.

This patch extends it to support both conjunctions and disjunctions
under the new name of netdev_increment_features.

It also adds a new function netdev_fix_features which does the
sanity checking that usually occurs upon registration.  This ensures
that the computation doesn't result in an illegal combination
since this checking is absent when the change is initiated via
ethtool.

The two users of netdev_compute_features have been converted.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-23 01:11:29 -07:00
Ben Dooks b22596726b drivers/net/bonding: sparse fixes for exported tables
The following sparse warnings are being generated
because bonding.h is missing definitons for items
declared in bond_main.c but also used in bond_sysfs.h

Also export bond_dev_list as this is also declared
in bond_main but used elsewhere in drivers/net/bonding.

bond_main.c:105:20: warning: symbol 'bonding_defaults' was not declared. Should it be static?
bond_main.c:148:1: warning: symbol 'bond_dev_list' was not declared. Should it be static?
bond_main.c:162:22: warning: symbol 'bond_lacp_tbl' was not declared. Should it be static?
bond_main.c:168:22: warning: symbol 'bond_mode_tbl' was not declared. Should it be static?
bond_main.c:179:22: warning: symbol 'xmit_hashtype_tbl' was not declared. Should it be static?
bond_main.c:186:22: warning: symbol 'arp_validate_tbl' was not declared. Should it be static?
bond_main.c:194:22: warning: symbol 'fail_over_mac_tbl' was not declared. Should it be static?

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 22:12:57 -04:00
Stephen Hemminger fa53ebac42 bonding: add more ethtool support
This patch allows reporting the link, checksum, and feature settings
of bonded device by using generic hooks.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:59:02 -04:00
Harvey Harrison b39d66a81f drivers/net: replace __FUNCTION__ with __func__
__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:59:00 -04:00
Vlad Yasevich 2d1ea19da0 bonding: Do not tx-balance some IPv6 packets on ALB/TLB bonds
IPv6 all-node-multicasts and DAD probes should not be tx-balanced
on ALB/TLB bonds.  The all-node-multicast is an equivalent to IPv4
broadcasts.  DAD probes have to be sent only on the primary so that
we don't get false-positive detections.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:49:01 -04:00
Brian Haley f14c4e4e36 bonding: change some __constant_htons() to htons()
Resending since I didn't see any responses from the first try.

Change __constant_htons() to htons() in the bonding driver, it should
only be used for initializers.

-Brian

Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 10:03:07 -04:00
Moni Shoua db018a5f49 bonding: Don't destroy bonding master when removing slave via sysfs
It is wrong to destroy a bonding master from a context that uses the sysfs
of that bond. When last IPoIB slave is unenslaved from by writing to a
sysfs file (for bond0 this would be /sys/class/net/bond0/bonding/slaves)
the driver tries to destroy the bond. This is wrong and can lead to a
lockup or a crash.  This fix lets the bonding master stay and relies on
the user to destroy the bonding master if necessary (i.e. before module
ib_ipoib is unloaded)

This patch affects only bonds of IPoIB slaves. Ethernet slaves stay
unaffected.

Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-07 03:59:56 -04:00
Jay Vosburgh f0c76d6177 bonding: refactor mii monitor
Refactor mii monitor.  As with the previous ARP monitor refactor,
the motivation for this is to handle locking rationally (in this case,
removing conditional locking) and generally clean up the code.

	This patch breaks up the monolithic mii monitor into two phases:
an inspection phase, followed by an optional commit phase.  The commit phase
is the only portion that requires RTNL or makes changes to state, and is
only called when inspection finds something to change.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-07 03:59:53 -04:00
David S. Miller cf508b1211 netdev: Handle ->addr_list_lock just like ->_xmit_lock for lockdep.
The new address list lock needs to handle the same device layering
issues that the _xmit_lock one does.

This integrates work done by Patrick McHardy.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-22 14:16:42 -07:00
David S. Miller e8a0464cc9 netdev: Allocate multiple queues for TX.
alloc_netdev_mq() now allocates an array of netdev_queue
structures for TX, based upon the queue_count argument.

Furthermore, all accesses to the TX queues are now vectored
through the netdev_get_tx_queue() and netdev_for_each_tx_queue()
interfaces.  This makes it easy to grep the tree for all
things that want to get to a TX queue of a net device.

Problem spots which are not really multiqueue aware yet, and
only work with one queue, can easily be spotted by grepping
for all netdev_get_tx_queue() calls that pass in a zero index.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-17 19:21:00 -07:00
David S. Miller b9e4085768 netdev: Do not use TX lock to protect address lists.
Now that we have a specific lock to protect the network
device unicast and multicast lists, remove extraneous
grabs of the TX lock in cases where the code only needs
address list protection.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-15 00:15:08 -07:00
David S. Miller e308a5d806 netdev: Add netdev->addr_list_lock protection.
Add netif_addr_{lock,unlock}{,_bh}() helpers.

Use them to protect operations that operate on or read
the network device unicast and multicast address lists.

Also use them in cases where the code simply wants to
block calls into the driver's ->set_rx_mode() and
->set_multicast_list() methods.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-15 00:13:44 -07:00
Wang Chen 7e1a1ac1fb bonding: Check return of dev_set_promiscuity/allmulti
dev_set_promiscuity/allmulti might overflow.
Commit: "netdevice: Fix promiscuity and allmulti overflow" in net-next makes
dev_set_promiscuity/allmulti return error number if overflow happened.

In bond_alb and bond_main, we check all positive increment for promiscuity
and allmulti to get error return.
But there are still two problems left.
1. Some code path has no mechanism to signal errors upstream.
2. If there are multi slaves, it's hard to tell which slaves increment
   promisc/allmulti successfully and which failed.
So I left these problems to be FIXME.
Fortunately, the overflow is very rare case.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-14 20:51:36 -07:00
David S. Miller c773e847ea netdev: Move _xmit_lock and xmit_lock_owner into netdev_queue.
Accesses are mostly structured such that when there are multiple TX
queues the code transformations will be a little bit simpler.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-08 23:13:53 -07:00
Jay Vosburgh b8a9787edd bonding: Allow setting max_bonds to zero
Permit bonding to function rationally if max_bonds is set to
zero.  This will load the module, but create no master devices (which can
be created via sysfs).

	Requires some change to bond_create_sysfs; currently, the
netdev sysfs directory is determined from the first bonding device created,
but this is no longer possible.  Instead, an interface from net/core is
created to create and destroy files in net_class.

	Based on a patch submitted by Phil Oester <kernel@linuxaces.com>.
Modified by Jay Vosburgh to fix the sysfs issue mentioned above and to
update the documentation.

Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 00:00:04 -04:00
Jay Vosburgh b59f9f74c4 bonding: Rework / fix multiple gratuitous ARP support
Support for sending multiple gratuitous ARPs during failovers
was added by commit:

commit 7893b2491a
Author: Moni Shoua <monis@voltaire.com>
Date:   Sat May 17 21:10:12 2008 -0700

    bonding: Send more than one gratuitous ARP when slave takes over

	This change modifies that support to remove duplicated code,
add support for ARP monitor (the original only supported miimon), clear
the grat ARP counter in bond_close (lest a later "ifconfig up" immediately
start spewing ARPs), and add documentation for the module parameter.

	Also updated driver version to 3.3.0.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 00:00:04 -04:00
Or Gerlitz 01f3109de4 bonding: deliver netdev event for fail-over under the active-backup mode
under active-backup mode and when there's actual new_active slave,
have bond_change_active_slave() call the networking core to deliver
NETDEV_BONDING_FAILOVER event such that the fail-over can be notable
by code outside of the bonding driver such as the RDMA stack and
monitoring tools.

As the correct context of locking appropriate for notifier calls is RTNL
and nothing else, bond->curr_slave_lock and bond->lock are unlocked and
later locked again. This is ensured by the rest of the code to be safe
under backup-mode AND when new_active is not NULL.

Jay Vosburgh modified the original patch for formatting and fixed a
compiler error.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-17 23:59:42 -04:00
Or Gerlitz 709f8a45e8 bonding: bond_change_active_slave() cleanup under active-backup
simplified the code of bond_change_active_slave() such that under
active-backup mode there's one "if (new_active)" test and the rest
of the code only does extra checks on top of it. This removed an
unneeded "if (bond->send_grat_arp > 0)" check and avoid calling
bond_send_gratuitous_arp when there's no active slave.

Jay Vosburgh made minor coding style changes to the orignal patch.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-17 23:59:41 -04:00
Jay Vosburgh 3915c1e863 bonding: Add "follow" option to fail_over_mac
Add a "follow" selection for fail_over_mac.  This option
causes the MAC address to move from slave to slave as the active
slave changes.  This is in addition to the existing fail_over_mac option
that causes the bond's MAC address to change during failover.

	This new option is useful for devices that cannot tolerate
multiple ports using the same MAC address simultaneously, either
because it confuses them or incurs a performance penalty (as is the
case with some LPAR-aware multiport devices).  Because the MAC of the
bond itself does not change, the "follow" option is slightly more
reliable during failover and doesn't change the MAC of the bond during
operation.

	This patch requires a previous ARP monitor change to properly
handle RTNL during failovers.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22 06:34:29 -04:00
Jay Vosburgh b2220cad58 bonding: refactor ARP active-backup monitor
Refactor ARP monitor for active-backup mode.  The motivation for
this is to take care of locking issues in a clear manner (particularly to
correctly handle RTNL vs. the bonding locks).  Currently, the a-b ARP
monitor does not hold RTNL at all, but future changes will require RTNL
during ARP monitor failovers.

	Rather than using conditional locking, this patch instead breaks
up the ARP monitor into three discrete steps: inspection, commit changes,
and probe.  The inspection phase marks slaves that require link state
changes.  The commit phase is only called if inspection detects that
changes are needed, and is called with RTNL.  Lastly, the probe phase
issues the ARP probes that the inspection phase uses to determine link
state.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22 06:34:28 -04:00
Moni Shoua 7893b2491a bonding: Send more than one gratuitous ARP when slave takes over
With IPoIB, reception of gratuitous ARP by neighboring hosts
is essential for a successful change of slaves in case of failure.
Otherwise, they won't learn about the HW address change and need
to wait a long time until the neighboring system gives up and sends
an ARP request to learn the new HW address.  This patch decreases
the chance for a lost of a gratuitous ARP packet by sending it more
than once. The number retries is configurable and can be set with a
module param.

Signed-off-by: Moni Shoua <monis@voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22 06:34:26 -04:00
Pavel Emelyanov 8047637c70 bonding: Remove unneeded list_empty checks.
Some places iterate over the checked list right after the check
itself, so even if the list is empty, the list_for_each_xxx
iterator will make everything right by himself.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22 06:34:25 -04:00
Pavel Emelyanov 0883beca7f bonding: Relax unneeded _safe lists iterations.
Many places either do not modify the list under the list_for_each_xxx,
or break out of the loop as soon as the first element is removed.

Thus, this _safe iteration just occupies some unneeded .text space
and requires an additional variable.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22 06:34:22 -04:00
Pavel Emelyanov 0dd646fe05 bonding: Remove redundant argument from bond_create.
While we're fixing the bond_create, I hope it's OK to polish it
a bit after the fixes.

The third argument is NULL at the first caller and is ignored by
the second one, so remove it.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22 06:34:21 -04:00
Jay Vosburgh 4b8a9239ee bonding: remove test for IP in ARP monitor
Remove bond_has_ip and all references to it.  With this change,
the ARP monitor will always send ARP probes if the master is up and has
at least one slave.  If the bond has an IP address, it is used in the
ARP probe; if not, the probes are sent with all zeros in the sender's
IP address (which is consistent with an RFC 2131 4.4.1 duplicate address
probe).

	This is useful for cases when bonding itself is hidden underneath
a layer of virtual devices, e.g., with Xen.

	Change suggested by Tsutomu Fujii <t-fujii@nb.jp.nec.com>, who
included a one-line patch that only affected active-backup mode.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22 06:34:18 -04:00
Jay Vosburgh 5ce0da8f03 bonding: Use msecs_to_jiffies, eliminate panic
Convert bonding to use msecs_to_jiffies instead of doing the
math.  For the ARP monitor, there was an underflow problem that could
result in an infinite loop.  The miimon already had that worked around,
but this is cleaner.

	Originally by Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Jay Vosburgh corrected a math error in the original; Nicolas' original
commit message is:

When setting arp_interval parameter to a very low value, delta_in_ticks
for next arp might become 0, causing an infinite loop.

See http://bugzilla.kernel.org/show_bug.cgi?id=10680

Same problem for miimon parameter already fixed, but fix might be
enhanced, by using msecs_to_jiffies() function.

Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22 06:34:17 -04:00
Stephen Hemminger 38d2f38be9 bonding: handle case of device named bonding_master
If device already exists named bonding_masters, then fail. This is a wierd
corner case only a QA group could love.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-05-14 22:35:04 -07:00
Jay Vosburgh 569f0c4d90 bonding: fix enslavement error unwinds
As part of:

commit c2edacf80e
Author: Jay Vosburgh <fubar@us.ibm.com>
Date:   Mon Jul 9 10:42:47 2007 -0700

    bonding / ipv6: no addrconf for slaves separately from master

two steps were rearranged in the enslavement process: netdev_set_master
is now before the call to dev_open to open the slave.

	This patch updates the error cases and unwind process at the
end of bond_enslave to match the new order.  Without this patch, it is
possible for the enslavement to fail, but leave the slave with IFF_SLAVE
set in its flags.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 12:01:32 -04:00
Pavel Emelyanov ae68c39819 bonding: Deadlock between bonding_store_bonds and bond_destroy_sysfs.
The sysfs layer has an internal protection, that ensures, that
all the process sitting inside ->sore/->show callback exits
before the appropriate entry is unregistered (the calltraces
are rather big, but I can provide them if required).

On the other hand, bonding takes rtnl_lock in
a) the bonding_store_bonds, i.e. in ->store callback,
b) module exit before calling the sysfs unregister routines.

Thus, the classical AB-BA deadlock may occur. To reproduce run
# while :; do modprobe bonding; rmmod bonding; done
and
# while :; do echo '+bond%d' > /sys/class/net/bonding_masters ; done
in parallel.

The fix is to move the bond_destroy_sysfs out of the rtnl_lock,
but _before_ bond_free_all to make sure no bonding devices exist
after module unload.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 12:01:30 -04:00
Jay Vosburgh c4ebc66a1a bonding: fix error unwind in bonding_store_bonds
Fixed an error unwind in bonding_store_bonds that didn't release
the locks it held, and consolidated unwinds into a common block at the
end of the function.  Bug reported by Pavel Emelyanov <xemul@openvz.org>,
who provided a different fix.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 12:01:29 -04:00
Pavel Emelyanov 822973ba79 bonding: Do not call free_netdev for already registered device.
If the call to bond_create_sysfs_entry in bond_create fails, the
proper rollback is to call unregister_netdevice, not free_netdev.
Otherwise - kernel BUG at net/core/dev.c:4057!

Checked with artificial failures injected into bond_create_sysfs_entry.

Pavel's original patch modified by Jay Vosburgh to move code around
for clarity (remove goto-hopping within the unwind block).

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 12:01:27 -04:00
Denis V. Lunev a95609cb02 netdev: use non-racy method for proc entries creation
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.

Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-29 08:06:22 -07:00
Joe Perches dc13b38599 drivers/net/bonding/bond_main.c - remove unnecessary #define
bond_main.c already #includes <linux/seq_file.h>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-16 20:09:35 -04:00
David S. Miller e1ec1b8ccd Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	drivers/net/s2io.c
2008-04-02 22:35:23 -07:00
David S. Miller 6952d8923b [BOND]: Fix warning in bond_sysfs.c
original_mtu is only used if we end up with a non-NULL
dev, and it is assigned in all such cases, but GCC can't
see that.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-03-28 16:15:38 -07:00
David S. Miller 8e8e43843b Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	drivers/net/usb/rndis_host.c
	drivers/net/wireless/b43/dma.c
	net/ipv6/ndisc.c
2008-03-27 18:48:56 -07:00
Jay Vosburgh 2cfb8b71cc bonding: update version
Update version to 3.2.5.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-25 23:15:51 -04:00
Libor Pechacek 92b41daa45 bonding: Fix sysfs attribute handling
For bonding interfaces any attempt to read the sysfs directory contents after
module removal results in an oops.  The fix is to release sysfs attributes
for the interfaces upon module unload.

Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-25 23:15:48 -04:00
Jay Vosburgh 966bc6f434 bonding: fix two compiler warnings
Fix two compiler warnings that are new with recent versions of gcc
(apparently 4.2 and up).  One is fixed by refactoring; this change was
supplied by Stephen Hemminger.  The other was fixed by labelling the
variable as uninitialized_var() after confirming via inspection that it
cannot actually be used uninitialized.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-25 23:15:40 -04:00
Jay Vosburgh 2bf86b7aa8 bonding: Fix locking in 802.3ad mode
The 802.3ad state machine lock can be acquired in both softirq and
not softirq context, but was not held at _bh to prevent a deadlock (which
could occur if a LACPDU arrived and was processed while the lock was
held).

	Corrected this, now hold the state machine lock at _bh to prevent
deadlock.

	Bug reported by Todd Fleisher <todd@fleish.org>.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-25 23:15:38 -04:00
YOSHIFUJI Hideaki c346dca108 [NET] NETNS: Omit net_device->nd_net without CONFIG_NET_NS.
Introduce per-net_device inlines: dev_net(), dev_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
2008-03-26 04:39:53 +09:00
Pavel Emelyanov 988b705077 [ARP]: Introduce the arp_hdr_len helper.
There are some place, that calculate the ARP header length. These
calculations are correct, but 
 a) some operate with "magic" constants,
 b) enlarge the code length (sometimes at the cost of coding style),
 c) are not informative from the first glance.

The proposal is to introduce a helper, that includes all the good
sides of these calculations.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-03-03 12:20:57 -08:00
Denis V. Lunev 6133fb1aa1 [NETNS]: Disable inetaddr notifiers in namespaces other than initial.
ip_fib_init is kept enabled. It is already namespace-aware.

Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-28 20:46:17 -08:00
Jay Vosburgh 43cd2595e7 bonding: update version
Update bonding to version 3.2.4.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-03 04:28:34 -08:00
Jay Vosburgh 21c9d8d73d bonding: do not acquire rtnl in ARP monitor
The ARP monitor functions currently acquire RTNL when performing
failover operations, but do so incorrectly (out of order).  This causes
various warnings from might_sleep.

	The ARP monitor isn't supported for any of the bonding modes
that actually require RTNL, so it is safe to not hold RTNL when
failing over in the ARP monitor.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-03 04:28:33 -08:00
Andy Gospodarek 2439f9ebd4 bonding: fix race that causes invalid statistics
I've seen reports of invalid stats in /proc/net/dev for bonding
interfaces, and found it's a pretty easy problem to reproduce.  Since
the current code zeros the bonding stats when a read is requested and a
pointer to that data is returned to the caller we cannot guarantee that
the caller has completely accessed the data before a successive call to
request the stats zeroes the stats again.

This patch creates a new stack variable to keep track of the updated
stats and copies the data from that variable into the bonding stats
structure.  This ensures that the value for any of the bonding stats
should not incorrectly return zero for any of the bonding statistics.
This does use more stack space and require an extra memcpy, but it seems
like a fair trade-off for consistently correct bonding statistics.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Chris Snook <csnook@redhat.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-03 04:28:13 -08:00
Jay Vosburgh 4fe4763cd8 bonding: fix NULL pointer deref in startup processing
Fix the "are we creating a duplicate" check to not compare
the name if the name is NULL (meaning that the system should select
a name).  Bug reported by Benny Amorsen <benny+usenet@amorsen.dk>.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-03 04:28:12 -08:00
Jay Vosburgh 80ee5ad231 bonding: fix set_multicast_list locking
This patch eliminates a problem (reported by lockdep) in the
bond_set_multicast_list function.  It first reduces the locking on
bond->lock to a simple read_lock, and second, adds netif_tx locking
around the bonding mc_list manipulations that occur outside of the
set_multicast_list function.

	The original problem was related to IPv6 addrconf activity.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-03 04:28:12 -08:00
Jay Vosburgh a42e534f1b bonding: fix parameter parsing
My last fix (commit ece95f7fef)
didn't handle one case correctly.  This resolves that, and it will now
correctly parse parameters with arbitrary white space, and either text
names or mode values.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-03 04:28:11 -08:00
Denis V. Lunev f206351a50 [NETNS]: Add namespace parameter to ip_route_output_key.
Needed to propagate it down to the ip_route_output_flow.

Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:11:07 -08:00
Jay Vosburgh 5655662dab bonding: Don't hold lock when calling rtnl_unlock
Change bond_mii_monitor to not hold any locks when calling rtnl_unlock,
as rtnl_unlock can sleep (when acquring another mutex in netdev_run_todo).

Bug reported by Makito SHIOKAWA <mshiokawa@miraclelinux.com>, who
included a different patch.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-18 14:38:39 -05:00
Jay Vosburgh 027ea0416c bonding: fix lock ordering for rtnl and bonding_rwsem
Fix the handling of rtnl and the bonding_rwsem to always be acquired
in a consistent order (rtnl, then bonding_rwsem).

The existing code sometimes acquired them in this order, and sometimes
in the opposite order, which opens a window for deadlock between ifenslave
and sysfs.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-18 14:38:39 -05:00
Jay Vosburgh ece95f7fef bonding: Fix up parameter parsing
A recent change to add an additional hash policy modified
bond_parse_parm, but it now does not correctly match parameters passed in
via sysfs.

	Rewrote bond_parse_parm to handle (a) parameter matches that
are substrings of one another and (b) user input with whitespace (e.g.,
sysfs input often has a trailing newline).

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-18 14:38:38 -05:00
Jay Vosburgh 3b96c858fc bonding: release slaves when master removed via sysfs
Add a call to bond_release_all in the bonding netdev event
handler for the master.  This releases the slaves for the case of, e.g.,
"echo -bond0 > /sys/class/net/bonding_masters", which otherwise will spin
forever waiting for references to be released.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-18 14:38:38 -05:00
Jay Vosburgh 2543331d36 bonding: fix locking during alb failover and slave removal
alb_fasten_mac_swap (actually rlb_teach_disabled_mac_on_primary)
requries RTNL and no other locks.  This could cause dev_set_promiscuity
and/or dev_set_mac_address to be called with improper locking.

	Changed callers to hold only RTNL during calls to alb_fasten_mac_swap
or functions calling it.  Updated header comments in affected functions to
reflect proper reality of locking requirements.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-18 14:38:38 -05:00
Jay Vosburgh e0138a66e1 bonding: fix ASSERT_RTNL that produces spurious warnings
Move an ASSERT_RTNL down to where we should hold only RTNL;
the existing check produces spurious warnings because we hold additional
locks at _bh, tripping a debug warning in spin_lock_mutex().

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-18 14:38:38 -05:00
Jay Vosburgh e934dd7862 bonding: fix locking in sysfs primary/active selection
Fix the functions that store the primary and active slave
options via sysfs to hold the correct locks in the correct order.

	The bond_change_active_slave and bond_select_active_slave
functions both require rtnl, bond->lock for read and curr_slave_lock for
write_bh, and no other locks.  This is so that the lower level
mode-specific functions (notably for balance-alb mode) can release locks
down to just rtnl in order to call, e.g., dev_set_mac_address with the
locks it expects (rtnl only).

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-18 14:38:38 -05:00
Jay Vosburgh fdaea7a93d bonding: Fix race at module unload
Fixes a race condition in module unload.  Without this change,
workqueue events may fire while bonding data structures are partially
freed but before bond_close() is invoked by unregister_netdevice().

	Update version to 3.2.3.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-07 15:00:34 -05:00
Jay Vosburgh 6f6652be18 bonding: Add new layer2+3 hash for xor/802.3ad modes
Add new hash for balance-xor and 802.3ad modes.  Originally
 submitted by "Glenn Griffin" <ggriffin.kernel@gmail.com>; modified by
 Jay Vosburgh to move setting of hash policy out of line, tweak the
 documentation update and add version update to 3.2.2.

	Glenn's original comment follows:

Included is a patch for a new xmit_hash_policy for the bonding driver
that selects slaves based on MAC and IP information.  This is a middle
ground between what currently exists in the layer2 only policy and the
layer3+4 policy.  This policy strives to be fully 802.3ad compliant by
transmitting every packet of any particular flow over the same link.
As documented the layer3+4 policy is not fully compliant for extreme
cases such as ip fragmentation, so this policy is a nice compromise
for environments that require full compliance but desire more than the
layer2 only policy.

Signed-off-by: "Glenn Griffin" <ggriffin.kernel@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-07 15:00:32 -05:00
David Sterba b63bb739a1 bonding: Fix time comparison
From: David Sterba <dsterba@suse.cz>

Use macros for comparing jiffies. Jiffies' wrap caused missed events and hangs.
Module reinsert was needed to make bonding work again.

Signed-off-by: David Sterba <dsterba@suse.cz>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-07 15:00:30 -05:00
Wagner Ferenc 8e4b932908 bonding: Allow setting and querying xmit policy regardless of mode
From: Wagner Ferenc <wferi@niif.hu>

For consistency with the behaviour of the arp_ip_target option,
let /sys/class/net/bond0/bonding/xmit_hash_policy accept and report
current policy even if the bonding mode in effect does not use it.

Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-07 15:00:28 -05:00
Wagner Ferenc 1dcdcd6954 bonding: Coding style: break line after the if condition
From: Wagner Ferenc <wferi@niif.hu>

Adhere to coding style: break line after the if condition

Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-07 15:00:27 -05:00
Wagner Ferenc b88436651b bonding: Purely cosmetic: rename a local variable
From: Wagner Ferenc <wferi@niif.hu>

Code for rendering multivalue sysfs files occurs three times
in this module.  Rename 'buffer' to 'buf' in the first, for
the sake of consistency.

Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-07 15:00:26 -05:00
Wagner Ferenc 16cd0160d5 bonding: Return nothing for not applicable values
From: Wagner Ferenc <wferi@niif.hu>

The previous code returned '\n' (that is, a single empty line)
from most files, with one exception (xmit_hash_policy), where
it returned 'NA\n'.  This patch consolidates each file to return
nothing at all if not applicable, not even a '\n'.

I find this behaviour more usual, more useful, more efficient
and shorter to code from both sides.

Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-07 15:00:25 -05:00
Wagner Ferenc 7bd4650895 bonding: Remove trailing NULs from sysfs interface.
From: Wagner Ferenc <wferi@niif.hu>

Also remove trailing spaces from multivalued files.

This fixes output like for example:

$ od -c /sys/class/net/bond0/bonding/slaves
0000000   e   t   h   -   l   e   f   t       e   t   h   -   r   i   g
0000020   h   t      \n  \0
0000025

It mostly entails deleting '+1'-s after sprintf() calls: the return value
of sprintf is the number of characters printed, without the closing NUL,
ie. exactly what the sysfs interface requires.  The three multivalue
cases are different, because they also have to swallow back a trailing
space.

Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-07 15:00:18 -05:00