pvrusb2: Declare closed-caption setup for line 21 - this is needed for
sliced VBI capture support. (However none of that works right now
anyway.)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: The origin of the capability bounds rectangle may differ from
(left=0,top=0) so the calculation should use absolute coordinates,
here below, or use relative coordinates like
cropl_val-cap->bounds.left and cropt_val-cap->bounds.top.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Recognize and handle mode change before dealing with changes
related to the video standard. Even though the video standard should
only matter when in analog mode, doing this way is technically cleaner
in case there's other stuff that might depend on both.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This tuner PLL has missing initialisation settings resulting in
haphazard tuning. The PLL LPF was set to just 22000 symbol rate.
Basically, the module is a Sharp BS2F7HZ0194 (STV0299+IX2410)
I have had problems implementing the PLL in a new driver and
did not want to break the IX2410 out of the PLL.
This applies to DW2102, DM1105, CX88 and OPERA1 drivers.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the drivers/ieee1394/ backend was removed from firedtv, its I/O no
longer needs to be abstracted as exchangeable backend methods.
Also, ieee1394 variants of module and device probe and removal are no
longer there. Move module probe and removal into firedtv-fw.c where
device probe and removal are implemented.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Speed up tuning, as firmware is not necessary to load every attempt to tune
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Decrease firmware loading time. Before it is ~4000 i2c calls,
now it is ~256 i2c calls to load ds3000 firmware.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
TeVii s480 works fine with that on DVB-S2 channels
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make some initializations in init, not in tune function
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds audio DMA capture and ALSA mixer elements for the line
input jack of the Hauppauge Nova-S-plus DVB-S PCI card. The Nova-S-plus
has a WM8775 ADC that is currently not detected. This patch enables
this chip and exports volume, balance mute and ALC elements for ALSA
mixer controls.
[mchehab@redhat.com: Changed the patch to only talk with wm8775 if board
info says so. Also, added platform_data support, to avoid changing the
behaviour for other boards, and fixed CodingStyle]
[awalls@md.metrocast.net: Changed patch to make the WM8775_GID defintion
bridge driver private and let the bridge driver set the value of
v4l2_subdev.grp_id.]
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Add one more radio input, usefull for tm6010
Add control output amplitude.
Add set_config function for configure tuner when TV card hasn't dvb part.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add linux/sched.h because of missing declaration of TASK_NORMAL.
This patch fixes the following error:
drivers/media/video/omap24xxcam.c: In function
'omap24xxcam_vbq_complete':
drivers/media/video/omap24xxcam.c:415: error: 'TASK_NORMAL' undeclared
(first use in this function)
drivers/media/video/omap24xxcam.c:415: error: (Each undeclared
identifier is reported only once
drivers/media/video/omap24xxcam.c:415: error: for each function it
appears in.)
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the warning "Using plain integer as NULL pointer",
generated by sparse, by replacing
if (var == 0)
with
if (!var)
after an allocation
and all other offending 0s with NULL.
KernelVersion: linus' tree-1f0324c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cxhdl->priv field was not set initially, only after capturing started.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It takes too long time to scan due to low symbol rate PID's
like PAT, PMT, CAT, NIT.
For that matter we enabled permanently all PID's
less 0x20 in hardware PID filter for NetUP Dual DVB-T/C CI RF card
to combine rates.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is needed for multifrontend support.
NetUP Dual DVB-T/C CI RF card has frontends connected to port B & C
Each frontend has two switchable cores - DVB-T & DVB-C
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is two external I2C buses in cx23885 chip.
Currently, analog tuners supported for second I2C bus only
In NetUP Dual DVB-T/C CI RF card tuners connected to first bus
So, in order to support analog tuners sitting on first bus
we need modifications.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card based on cx23885 PCI-e brige. Altera FPGA for CI,
multistandard demods stv0367 from STM for QAM & OFDM, Xcieve xc5000 tuners
and additional cx25840 for second analog input.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The STV0367 is a multi-standard demodulator which is
capable of processing DVB-T as well as DVB-C signals.
It is fully compliant with DVB-T and DVB-C
recommendations for broadcast services.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
An Altera FPGA CI module for NetUP Dual DVB-T/C RF CI card.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the warning "Using plain integer as NULL pointer",
generated by sparse, by replacing the offending 0s with NULL.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This soc_camera driver is for Omnivision's OV9740 sensor. This initial
submission provides support for YUV422 output at 1280x720 (720p), which is
the sensor's native resolution. 640x480 (VGA) is also supported, with
cropping and scaling performed by the sensor's ISP.
This driver is heavily based off of the existing OV9640 driver.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that soc-camera supports videobuf API v1 and v2, camera-host drivers
can be converted to videobuf2 individually. This patch converts the
mx3_camera driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Extend soc-camera core to also support the videobuf2 API.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf2-memops and videobuf2-core can be compiled as modules, in which
case 3 more symbols from videobuf2-memops.c have to be exported.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the camera was set to output formats like RGB565 YUYV or SBGGR10,
the resulting image was scrambled due to erroneous interpretations of
horizontal parameter's units.
This patch in fourcc_to_ipu_pix, eliminate also the pixel formats mappings
that, first are not used within mainline code and second, standing at
the datasheets, they will not work properly:
The IPU internal bus support only the following data formatting
(44.1.1.3 Data Flows and Formats):
1 YUV 4:4:4 or RGB-8 bits per color component
2 YUV 4:4:4 or RGB-10 bits per color component
3 Generic data (from sensor to the system memory only)
And format conversions are done:
- from memory: unpacking from other formats to IPU supported ones
- to memory: packing in the inverse order.
So, assigning a packing/unpacking strategy to the IPU for those formats
will produce a packing to memory and not the inverse.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'pix->width' field may be updated in mx3_camera_set_fmt() to
fulfill the IPU stride line alignment requirements. If this update
takes place, the 'fmt.pix.sizeimage' field in the struct v4l2_format
stucture returned by VIDIOC_S_FMT is wrong. We need to update the
'pix->sizeimage' field in the mx3_camera_set_fmt() function to fix
this issue.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Even though clk_put() is a no-op on most architectures it is not for
some ARM implementations. To not fail on those, release the clock timer
before freeing the surrounding structure.
This bug was spotted by the semantic patch tool coccinelle using the
script found at scripts/coccinelle/free/kfree.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a function to calculate the number of samples on the media-bus,
required to retrieve one pixel of a certain format.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some camera systems have strong requirement for capturing
an exact number of frames after starting the stream and do
not tolerate losing captured frames. By starting the stream
after the videobuf has queued the buffers, we ensure that
no frame will be lost.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reported by, and based on a patch from, Martin Dauskardt.
The AUDIO_AC3_BITRATE control is still missing from this list, but such
optional controls are a bit hard to handle. This will be fixed automatically
when we switch to the control framework.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/ieee1394/ has been removed in Linux 2.6.37. The corresponding
backend code in firedtv is no longer built in now and can be deleted.
Firedtv continues to work with drivers/firewire/.
Also, fix a Kconfig menu comment: Removal of CONFIG_IEEE1394 made the
"Supported FireWire (IEEE 1394) Adapters" comment disappear; bring it back
with corrected dependency.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some ioctl's were defined wrong on 2.6.2 and 2.6.6, using the wrong
type of R/W arguments. They were fixed, but the old ioctl names are
still there, maintained to avoid breaking binary compatibility:
There's no sense on preserving those forever, as it is very doubtful
that someone would try to use a such old binary with a modern kernel.
Removing them will allow us to remove some magic done at the V4L ioctl
handler.
Note that any application compiled with a videodev2.h from 2.6.7 or later
will be using the correct ioctls.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Having a framerate divisor of 3 is not really necesarry and leads to
various troubles (frames going missing, compression issues) when allowed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a complete rewrite of the old v4l1 vicam subdriver, featuring
multiple resolutions, gain + exposure control and still has less code.
Oh and it is a v4l2 driver rather then v4l1 ofcourse :)
Many thanks to Devin Heitmueller <dheitmueller@kernellabs.com> for
donating his 3com homeconnect to me, which made this rewrite possible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In good lighting conditions (lots of details visible) the current buffers
are sometimes too small.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes the led not working on this camera
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with a camera with usb-id: 0c45:62bb
Also enable dmi based flopped laptop detection for the 0c45:627b ov7660 model.
Some of the MSI laptops with upside down camera have this one instead of the
0c45:624f.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with a camera with usb-id: 0c45:62bb
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
During image capture, the filling rate of the isoc packets is computed.
It is then used by a work queue to update the current JPEG quality.
Tested-by: Franck Bourdonnec <fbourdonnec@chez.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A marker 'ff ff 00 c4 c4 96' indicates an end of frame.
It is 62 bytes long and may be splitted on 2 packets.
It contains a flag 'USB full' which indicates that the frame is truncated.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2-ctl and qv4l2 enumerate controls using V4L2_CTRL_FLAG_NEXT_CTRL,
falling back to the old method if the flag isn't supported.
The v4l2_subdev_queryctrl function will currently handle that flag, but
for the controls of the subdev only. This isn't right, it should refuse
this flag, otherwise v4l2-ctl will only see the controls of the first
subdev.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Subdev controls return codes are evil, as they return -EINVAL to mean
both unsupported and invalid arguments. Due to that, we need to use a
trick to identify what controls are supported by a subdev.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On some cases, driver returns 1. This should be OK, but qv4l2 is too
strict about return values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Having the device detection happening at reset is bad, as every time,
it will produce a message like:
tvp5150 2-005c: tvp5150am1 detected.
This only polutes the log and for an accidental kernel hacker, it looks
like a real problem. So, move those printk's to happen during device
probe.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It makes no sense that tuner_lookup would touch at the standby
state. Remove it.
Thanks-to: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Group a few functions together and add/fix comments for each
block of the driver.
This is just a cleanup patch meant to improve driver readability.
No functional changes in this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is complex, and used by everyone. Better to have it
properly documented.
No functional changes are done in this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tuner-core has no business to do with digital TV. So, don't use
T_DIGITAL_TV on it, as it has no code to distinguish between
them, and nobody fills T_DIGITAL_TV right.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda9887 used to use the T_STANDBY type internally, while tea5761
used it to put the device to sleep. Fix the code for it to work
properly with the tuner core changes and remove this flag from
tuner.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the now obsolete set_freq. Also merge set_addr and set_type_addr.
In the past, it used to have two different setup calls, one to set just
the tuner type to any tuner found, and another to set the type only if
the address matches. Those two internal calls were grouped together,
but the functions weren't merged, making the code uglier.
No functional changes are done in this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A static var is evil, especially if a device has two boards with
xc5000. Instead, just like the other drivers, use stack to store
its config during setup.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Power down tuners at suspend. At resume, if the tuner is in standby,
calls set_mode, that will turn it on and set the latest frequencies.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the past, T_STANDBY were used on devices with a separate radio tuner to
mark a tuner that were disabled. With the time, it got newer meanings.
Also, due to a bug at the logic, the driver might incorrectly return
T_STANDBY to userspace.
So, instead of keeping the abuse, just use a boolean for storing
such information.
We can't remove T_STANDBY yet, as this is used on two other drivers. A
latter patch will address its usage outside tuner-core.
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Properly document those functions and do some cleanups around that.
There's just one behavior change on this patchset: it will now restore
TV frequency when changing from radio to TV mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a big patch with no functional changes. It just
rearranges everything inside the driver, and prepares to
break TV and Radio into two separate fops groups.
Currently, it has an heuristics logic to determine if the
call came from radio or video. However, the caller driver
knows for sure, so tuner-core shouldn't try to guess it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After registering the cdev, it would be possible do have an open on it.
In a matter of fact, some versions of udev do this. So, move registration
to the end and protect it with a mutex.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds support for Pixelviex Xcapture USB grabber device.
This device has one composite and one s-video entry
only, plus a button.
For now, the button is not supported.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices don't need to use it. So allow to just disable this logic.
Having it enabled on some devices cause power management to complain,
generating error -71.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of per-model tests all over the code, use some parameters
at the board entries to describe the model variants for:
- devices with 417 MPEG encoder;
- devices that use external AV;
- devices where vbi VANC endpoint doesn't work;
- devices with xc5000 that require different IF
initialization (and probably will cover also
xc3028).
- devices with xceive tuner that require a reset
during init.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The check for xc5000 assumes that the tuner will always
be using the same bus and will have the same address.
As those are configurable via dev->board, it should use,
instead, the values defined there.
Also, a similar type of test will be needed by other
tuners (for example, for TUNER_XC2028)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just a cleanup patch. Removes one indent level by moving
the return -ENODEV to happen before the device register
logic, if the interface is not the audio/video (int 1).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My Hauppauge WinTV HVR-1400 needs sometimes more then only one retry to load the firmware successfully.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
KERNEL_VERSION: 2.6.37
common.c in function ssize_t si470x_fops_read.
1. First mutex_lock on &radio->lock in line 441
2. Second in line 462
I think that mutex in line 462 is not needed.
433static ssize_t si470x_fops_read(struct file *file, char __user *buf,
434 size_t count, loff_t *ppos)
435{
....
441 mutex_lock(&radio->lock);
442 if ((radio->registers[SYSCONFIG1] & SYSCONFIG1_RDS) == 0)
443 si470x_rds_on(radio);
444
445 /* block if no new data available */
446 while (radio->wr_index == radio->rd_index) {
447 if (file->f_flags & O_NONBLOCK) {
448 retval = -EWOULDBLOCK;
449 goto done;
450 }
451 if (wait_event_interruptible(radio->read_queue,
452 radio->wr_index != radio->rd_index) < 0) {
453 retval = -EINTR;
454 goto done;
455 }
456 }
457
458 /* calculate block count from byte count */
459 count /= 3;
460
461 /* copy RDS block out of internal buffer and to user buffer */
462 mutex_lock(&radio->lock);
Found by Linux Device Drivers Verification Project
Remove second mutex.
Signed-off-by: Alexander Strakh <strakh@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Unable to test this due to lack of hardware.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/vivi.c:1059: warning: this decimal constant is unsigned only in ISO C90
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely