Pull i2c updates from Wolfram Sang:
"For 3.19, the I2C subsystem has to offer special candy this time.
Right in time for Christmas :)
- I2C slave framework: finally, a generic mechanism for Linux being
an I2C slave (if the bus driver supports that). Docs are still
missing but will come later this cycle, the code is good enough to
go.
- I2C muxes represent their topology in sysfs much more detailed.
This will help users to navigate around much easier.
- irq population of i2c clients is now done at probe time, not device
creation time, to have better support for deferred probing.
- new drivers for Imagination SCB, Amlogic Meson
- DMA support added for Freescale IMX, Renesas SHMobile
- slightly bigger driver updates to OMAP, i801, AT91, and rk3x
(mostly quirk handling, timing updates, and using better kernel
interfaces)
- eeprom driver can now write with byte-access (very slow, but OK to
have)
- and the bunch of smaller fixes, cleanups, ID updates..."
* 'i2c/for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (56 commits)
i2c: sh_mobile: remove unneeded DMA mask
i2c: rcar: add slave support
i2c: slave-eeprom: add eeprom simulator driver
i2c: core changes for slave support
MAINTAINERS: add I2C dt bindings also to I2C realm
i2c: designware: Fix falling time bindings doc
i2c: davinci: switch to use platform_get_irq
Documentation: i2c: Use PM ops instead of legacy suspend/resume
i2c: sh_mobile: optimize irq entry
i2c: pxa: add support for SCCB devices
omap: i2c: don't check bus state IP rev3.3 and earlier
i2c: s3c2410: Handle i2c sys_cfg register in i2c driver
i2c: rk3x: add Kconfig dependency on COMMON_CLK
i2c: omap: add notes related to i2c multimaster mode
i2c: omap: don't reset controller if Arbitration Lost detected
i2c: omap: implement workaround for handling invalid BB-bit values
i2c: omap: cleanup register definitions
i2c: rk3x: handle dynamic clock rate changes correctly
i2c: at91: enable probe deferring on dma channel request
i2c: at91: remove legacy DMA support
...
This patch documents the device isl29028 with its vendor-prefix. Undocumented deprecated vendor-prefix
found by checkpatch also documented for compatibility reasons.
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This allows checkpatch to validate more DTSes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This allows checkpatch to validate more DTSes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some DS13XX devices have "trickle chargers". Introduce a device tree
binding for the resistor and diode configuration for enabling trickle
charger.
Signed-off-by: Matti Vaittinen <matti.vaittinen@nsn.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pavel Machek <pavel@denx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series updates the device tree vendor prefix for
Dialog Semiconductor.
Various methods are currently used throughout the kernel: 'diasemi',
'dialog' and 'dlg'. Others have also been suggested.
This patch set aims to consolidate the usage of the vendor prefix to
use a common standard. The prefix 'dlg' is used.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Heiko Schocher provided a driver for TI TMP103.
Kamil Debski provided a driver for pwm-controlled fans.
Neelesh Gupta provided a driver for power, fan rpm, voltage and temperature
reporting on powerpc/powernv systems.
Scott Kanowitz provided a driver supporting Lattice's POWR1220 power manager IC.
Richard Zhu provided a pmbus front-end driver for TPS40422.
Frans Klaver added support for TMP112 to the lm75 driver.
Johannes Pointner added support for EPCOS B57330V2103 to the ntc_thermistor
driver.
Guenter Roeck added support for TMP441 and TMP442 to the tmp421 driver.
Axel Lin converted several drivers to the new hwmon API (36 of them, if I
counted correctly), and cleaned up many of the drivers along the way.
There are also a number of patches fixing bugs discovered while testing
Axel's changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9j+M
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Notable changes:
- Heiko Schocher provided a driver for TI TMP103.
- Kamil Debski provided a driver for pwm-controlled fans.
- Neelesh Gupta provided a driver for power, fan rpm, voltage and
temperature reporting on powerpc/powernv systems.
- Scott Kanowitz provided a driver supporting Lattice's POWR1220
power manager IC.
- Richard Zhu provided a pmbus front-end driver for TPS40422.
- Frans Klaver added support for TMP112 to the lm75 driver.
- Johannes Pointner added support for EPCOS B57330V2103 to the
ntc_thermistor driver.
- Guenter Roeck added support for TMP441 and TMP442 to the tmp421
driver.
- Axel Lin converted several drivers to the new hwmon API (36 of
them, if I counted correctly), and cleaned up many of the drivers
along the way.
There are also a number of patches fixing bugs discovered while
testing Axel's changes"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (88 commits)
hwmon: (g762) Use of_property_read_u32 at appropriate place
hwmon: (sis5595) Prevent overflow problem when writing large limits
hwmon: (gpio-fan) Prevent overflow problem when writing large limits
hwmon: (ibmpowernv) Use of_property_read_u32 at appropriate place
hwmon: (lm85) Convert to devm_hwmon_device_register_with_groups
hwmon: (lm85) Avoid forward declaration
hwmon: (lm78) Convert to devm_hwmon_device_register_with_groups
hwmon: (max6697) Use of_property_read_bool at appropriate places
hwmon: (pwm-fan) Make SENSORS_PWM_FAN depend on OF
hwmon: (pwm-fan) Remove duplicate dev_set_drvdata call
hwmon: (nct6775) Remove num_attr_groups from struct nct6775_data
hwmon: (nct6775) Update module description and Kconfig for NCT6106D and NCT6791D
hwmon: (adt7411) Convert to devm_hwmon_device_register_with_groups
hwmon: (g762) Convert to hwmon_device_register_with_groups
hwmon: (emc2103) Convert to devm_hwmon_device_register_with_groups
hwmon: (smsc47m1) Avoid forward declaration
hwmon: (smsc47m192) Convert to devm_hwmon_device_register_with_groups
hwmon: (smsc47m192) Avoid forward declaration
hwmon: (max1668) Make max1668_addr_list array const
hwmon: (max6639) Make normal_i2c array const
...
Driver for the TI TMP103.
The TI TMP103 is similar to the TMP102. It differs from the TMP102
by having only 8 bit registers.
Signed-off-by: Heiko Schocher <hs@denx.de>
[linux@roeck-us.net: Select REGMAP_I2C in Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Allow the mma8452 to be described in the device tree.
Since no device specific binding attributes exist the trivial
I2C binding is sufficient to describe the compatible string.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a number of eeproms and temperature sensors/fan controllers used
by kirkwood boards.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Rob Herring <robh@kernel.org>
A large part of the arm-soc patches are nowadays DT changes, adding support
for new SoCs, boards and devices without changing kernel source. The plan
is still to move the devicetree files out of the kernel tree and reduce
the amount of churn going on here, but we keep finding reasons to delay
doing that.
Changes are really all over the place, with little sticking out particularly.
We have contributions from a total of 116 people in this branch.
Unfortunately, the size of this branch also causes a significant number
of conflicts at the moment, typically when subsystem maintainers merge
patches that change the driver at the same time as the dts files. In
most cases this could be avoided because the dts changes are supposed
to be compatible in both ways, and we are asking everyone to send ARM
dts changes through our tree only.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zl/N
-----END PGP SIGNATURE-----
Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
Add the Seiko Instruments Inc S35390a to the list of trivial i2c
devices.
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds a trivial Device Tree binding to the I2C-based
cs42l51 sound codec, so that it can be used from Device Tree based
platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
Add Capella Microsystem CM32181 Ambient Light Sensor IIO driver.
This driver will convert raw data to lux value under open-air
condition. Change the calibscale based on the cover material.
Signed-off-by: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Intersil ISL12057 is an I2C RTC chip also supporting two alarms. This
patch only adds support for basic RTC functionalities (i.e. getting
and setting time). Tests have been performed on NETGEAR ReadyNAS 102
w/ startup/shutdown scripts, hwclock, ntpdate and openntpd.
Reviewed-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
acpi_power_meter: Fix return value check from call to acpi_bus_get_device
nct6775: Fix/improve NCT6791 support
lm75: Add support for GMT G751
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ObF6
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- acpi_power_meter: Fix return value check from call to
acpi_bus_get_device
- nct6775: Fix/improve NCT6791 support
- lm75: Add support for GMT G751
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (acpi_power_meter) Fix acpi_bus_get_device() return value check
hwmon: (nct6775) NCT6791 supports weight control only for CPUFAN
hwmon: (nct6775) Monitor additional temperature registers
hwmon: (lm75) Add support for GMT G751 chip
This was tested on a NETGEAR ReadyNAS 2120 device (Marvell Armada XP
based board, via DT).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This is based on the work of Teddy Reed <teddy@prosauce.org> published
on GitHub:
https://github.com/theopolis/tpm-i2c-atmel.git
34894b988b67e0ae55088d6388e77b0dbf10c07d
That driver was never merged, I have taken it as a starting port,
forward ported, tested and revised the driver:
- Make it broadly textually similar to the Infineon and Nuvoton I2C
driver
- Place everything in a format suitable for mainline inclusion
- Use high level I2C functions i2c_master_send and
i2c_master_recv for data xfer
- Use the timeout system from the core code, by faking out a status
register
- Only I2C transfer the number of bytes in the reply, not a fixed
message size.
- checkpatch cleanups
- Testing on ARM Kirkwood, with this device tree, using a
AT97SC3204T-X1A180
tpm@29 {
compatible = "atmel,at97sc3204t";
reg = <0x29>;
};
Signed-off-by: Teddy Reed <teddy@prosauce.org>
[jgg: revised and tested]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor whitespace changes]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This chip is/was also branded as a Winbond WPCT301.
Originally written by Dan Morav <dmorav@nuvoton.com> and posted to LKML:
https://lkml.org/lkml/2011/9/7/206
The original posting was not merged, I have taken it as a
starting point, forward ported, tested and revised the driver:
- Rework interrupt handling to work properly with level triggered
interrupts. The old version just locked up.
- Synchronize various items with Peter Huewe's Infineon driver:
* Add durations/timeouts sysfs calls
* Remove I2C device auto-detection
* Don't fiddle with chip->release
* Call tpm_dev_vendor_release in the probe error path
* Use MODULE_DEVICE_TABLE for the I2C ids
* Provide OF compatible strings for DT support
* Use SIMPLE_DEV_PM_OPS
* Use module_i2c_driver
- checkpatch cleanups
- Testing on ARM Kirkwood with GPIO interrupts, with this device tree:
tpm@57 {
compatible = "nuvoton,npct501";
reg = <0x57>;
interrupt-parent = <&gpio1>;
interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
};
Signed-off-by: Dan Morav <dmorav@nuvoton.com>
[jgg: revised and tested]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor whitespace changes, fixed module name in kconfig]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This driver adds support for Infineon's new SLB 9645 TT 1.2 I2C TPMs,
which supports clockstretching, combined reads and a bus speed of
up to 400khz. The device also has a new device id.
The driver works now also fine with device trees, so you can
instantiate your device by adding:
+ tpm {
+ compatible = "infineon,slb9645tt";
+ reg = <0x20>;
+ };
for SLB 9645 devices or
+ tpm {
+ compatible = "infineon,slb9635tt";
+ reg = <0x20>;
+ };
for SLB 9635 devices
to your device tree.
tpm_i2c_infineon is also retained as a compatible id as a fallback to
slb9635 protocol.
The driver was tested on Beaglebone.
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Update i2c trivial-devices list by adding the description for
ti,tmp275 temperature sensor and taos,tsl2550 ambient light
sensor.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Based on recent discussions, we apparently want to do bindings even for
trivial i2c devices, even though they have for years just been added. So
start a table of the currently known ones for others to be added to
over time.
(I am intentionally letting lines go over 80 characters to make it easier
to sort the file).
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Linus Torvalds