The Revision 1.0 Janz CMOD-IO Carrier Board does not have support for
the reset registers. To support older hardware, the code is changed to
use the hardware reset register on the Janz VMOD-ICAN3 hardware itself.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Daniel writes:
Essentially just flush my -fixes queue before I head off to xdc.
- gen2 regression fixer, we've enabled the lvds stuff too late. Not
causing any known issues, but this restores the sequence before a
refactor that landed in 3.5, and lvds is a fickle beast. And seriously,
who runs gen2 still ...
- downgrade a BUG to a WARN - we haven't root-caused/fixed the underlying
issue yet, but this should help bug reporters quite a bit.
- properly disable hdmi audio - we've lost track of this, which resulted
in the alsa driver again losing track of the unplug event.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug
drm/i915: Reduce a pin-leak BUG into a WARN
drm/i915: enable lvds pin pairs before dpll on gen2
This fixes the gpio reset problem so the Retina MBP works, but avoids
breaking the Dell systems. Ben will work on a better solution for 3.7.
Tested by me on retina MBP.
Signed-off-by: Dave Airlie <airlied@redhat.com>
A change in a series of VLAN-related changes appears to have
inadvertently disabled the use of the scatter gather feature of
network cards for transmission of non-IP ethernet protocols like ATA
over Ethernet (AoE). Below is a reference to the commit that
introduces a "harmonize_features" function that turns off scatter
gather when the NIC does not support hardware checksumming for the
ethernet protocol of an sk buff.
commit f01a5236bd
Author: Jesse Gross <jesse@nicira.com>
Date: Sun Jan 9 06:23:31 2011 +0000
net offloading: Generalize netif_get_vlan_features().
The can_checksum_protocol function is not equipped to consider a
protocol that does not require checksumming. Calling it for a
protocol that requires no checksum is inappropriate.
The patch below has harmonize_features call can_checksum_protocol when
the protocol needs a checksum, so that the network layer is not forced
to perform unnecessary skb linearization on the transmission of AoE
packets. Unnecessary linearization results in decreased performance
and increased memory pressure, as reported here:
http://www.spinics.net/lists/linux-mm/msg15184.html
The problem has probably not been widely experienced yet, because
only recently has the kernel.org-distributed aoe driver acquired the
ability to use payloads of over a page in size, with the patchset
recently included in the mm tree:
https://lkml.org/lkml/2012/8/28/140
The coraid.com-distributed aoe driver already could use payloads of
greater than a page in size, but its users generally do not use the
newest kernels.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the network layer to see that AoE requires
no checksumming in a generic way, the packets must be
marked as requiring no checksum, so we make this requirement
explicit with the assertion.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we are currently returning ENODEV, as the clk_get may give a exact
error code in its returned pointer, assign it to the ret by using the
PTR_ERR function, so that the subsequent goto label will jump to the
error path and clean the driver and return the error correctly.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ESN replay window was already fully initialized in
xfrm_alloc_replay_state_esn(). No need to copy it again.
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code fails to ensure that the netlink message actually
contains as many bytes as the header indicates. If a user creates a new
state or updates an existing one but does not supply the bytes for the
whole ESN replay window, the kernel copies random heap bytes into the
replay bitmap, the ones happen to follow the XFRMA_REPLAY_ESN_VAL
netlink attribute. This leads to following issues:
1. The replay window has random bits set confusing the replay handling
code later on.
2. A malicious user could use this flaw to leak up to ~3.5kB of heap
memory when she has access to the XFRM netlink interface (requires
CAP_NET_ADMIN).
Known users of the ESN replay window are strongSwan and Steffen's
iproute2 patch (<http://patchwork.ozlabs.org/patch/85962/>). The latter
uses the interface with a bitmap supplied while the former does not.
strongSwan is therefore prone to run into issue 1.
To fix both issues without breaking existing userland allow using the
XFRMA_REPLAY_ESN_VAL netlink attribute with either an empty bitmap or a
fully specified one. For the former case we initialize the in-kernel
bitmap with zero, for the latter we copy the user supplied bitmap. For
state updates the full bitmap must be supplied.
To prevent overflows in the bitmap length calculation the maximum size
of bmp_len is limited to 128 by this patch -- resulting in a maximum
replay window of 4096 packets. This should be sufficient for all real
life scenarios (RFC 4303 recommends a default replay window size of 64).
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Martin Willi <martin@revosec.ch>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory used for the template copy is a local stack variable. As
struct xfrm_user_tmpl contains multiple holes added by the compiler for
alignment, not initializing the memory will lead to leaking stack bytes
to userland. Add an explicit memset(0) to avoid the info leak.
Initial version of the patch by Brad Spengler.
Cc: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory reserved to dump the xfrm policy includes multiple padding
bytes added by the compiler for alignment (padding bytes in struct
xfrm_selector and struct xfrm_userpolicy_info). Add an explicit
memset(0) before filling the buffer to avoid the heap info leak.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory reserved to dump the xfrm state includes the padding bytes of
struct xfrm_usersa_info added by the compiler for alignment (7 for
amd64, 3 for i386). Add an explicit memset(0) before filling the buffer
to avoid the info leak.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
copy_to_user_auth() fails to initialize the remainder of alg_name and
therefore discloses up to 54 bytes of heap memory via netlink to
userland.
Use strncpy() instead of strcpy() to fill the trailing bytes of alg_name
with null bytes.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the modes of Huawei E367 has this QMI/wwan interface:
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=07 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Huawei use subclass and protocol to identify vendor specific
functions, so adding a new vendor rule for this combination.
The Pantech devices UML290 (106c:3718) and P4200 (106c:3721) use
the same subclass to identify the QMI/wwan function. Replace the
existing device specific UML290 entries with generic vendor matching,
adding support for the Pantech P4200.
The ZTE MF683 has 6 vendor specific interfaces, all using
ff/ff/ff for cls/sub/prot. Adding a match on interface #5 which
is a QMI/wwan interface.
Cc: Fangxiaozhi (Franko) <fangxiaozhi@huawei.com>
Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Shawn J. Goff <shawn7400@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
rcv_wscale is a symetric parameter with snd_wscale.
Both this parameters are set on a connection handshake.
Without this value a remote window size can not be interpreted correctly,
because a value from a packet should be shifted on rcv_wscale.
And one more thing is that wscale_ok should be set too.
This patch doesn't break a backward compatibility.
If someone uses it in a old scheme, a rcv window
will be restored with the same bug (rcv_wscale = 0).
v2: Save backward compatibility on big-endian system. Before
the first two bytes were snd_wscale and the second two bytes were
rcv_wscale. Now snd_wscale is opt_val & 0xFFFF and rcv_wscale >> 16.
This approach is independent on byte ordering.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
CC: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Andrew Vagin <avagin@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixes a resume regression on pre-r6xx asics.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Prevent leak of scratch register on resume from suspend
When allocating memory fails, page is NULL. page_to_pfn() will
cause the kernel panicked if we don't use sparsemem vmemmap.
Link: http://lkml.kernel.org/r/505AB1FF.8020104@cn.fujitsu.com
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cards typically have 5-7 scratch registers; one of these is reserved for
rdev->rptr_save_reg. Unfortunately the reservation is done in function
r100_cp_init, which is called by all drivers except r600 - and this
function is also invoked on resume from suspend. After several resumes,
no scratch registers are free and graphics acceleration is disabled.
Dmesg then reports either:
*ERROR* radeon: cp failed to get scratch reg (-22).
*ERROR* radeon: cp isn't working(-22).
radeon 0000:01:00.0: failed initializing CP (-22).
or:
*ERROR* radeon: failed to get scratch reg (-22).
*ERROR* radeon: failed testing IB on GFX ring (-22).
*ERROR* ib ring test failed (-22).
The chain of calls on boot for all except r600 is:
radeon_init -> ... -> (rXXX_init) -> rXXX_startup -> r100_cp_init
The chain of calls on resume for all except r600 is:
rXXX_resume -> rXXX_startup -> r100_cp_init.
R600 correctly allocates rptr_save_reg in r600_init (ie once only, not
in resume). However moving the code into the init functions for all
drivers means touching 4 drivers. So instead, this patch just adds a
test in r100_cp_init to avoid reallocating on resume. As the rdev
structure is allocated via kzalloc in radeon_driver_load_kms, and zero
is not a valid registerid, zero safely implies not-yet-allocated.
This issue appears to have been introduced in c7eff978 (3.6.0-rcN)
Signed-off-by: Simon Kitching <skitching@vonos.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 991083ba60.
We discovered this causes problem on some Dell eDP laptops, so Apple
lose out for now, I might try and whip up a dmi based workaround for 3.6
but I'm not sure I'll get time.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The pll fix ended up causing some regressions. Drop it for 3.6. I've
fixed it properly in 3.7, but the fix is too invasive for 3.6.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
Revert "drm/radeon: rework pll selection (v3)"
copy_to_user() returns the number of bytes remaining, but we want a
negative error code here.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When lifing finger off the surface some versions of touchpad send movement
packets with very low coordinates, which cause cursor to jump to the upper
left corner of the screen. Let's ignore least significant bits of X and Y
coordinates if higher bits are all zeroes and consider finger not touching
the pad.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43197
Reported-and-tested-by: Aleksey Spiridonov <leks13@leks13.ru>
Tested-by: Eddie Dunn <eddie.dunn@gmail.com>
Tested-by: Jakub Luzny <limoto94@gmail.com>
Tested-by: Olivier Goffart <olivier@woboq.com>
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Clocks must be prepared before enabling and unprepared
after disabling. Use appropriate functions to do this
in one go.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On Toshiba Satellite C850D, the touchpad and the keyboard might randomly
not work at boot. Preventing MUX mode activation solves this issue.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It should be the skb which is not cloned
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Running cpufreq driver on imx6q, the following warning is seen.
$ BUG: sleeping function called from invalid context at kernel/mutex.c:269
<snip>
stack backtrace:
Backtrace:
[<80011d64>] (dump_backtrace+0x0/0x10c) from [<803fc164>] (dump_stack+0x18/0x1c)
r6:bf8142e0 r5:bf814000 r4:806ac794 r3:bf814000
[<803fc14c>] (dump_stack+0x0/0x1c) from [<803fd444>] (print_usage_bug+0x250/0x2b
8)
[<803fd1f4>] (print_usage_bug+0x0/0x2b8) from [<80060f90>] (mark_lock+0x56c/0x67
0)
[<80060a24>] (mark_lock+0x0/0x670) from [<80061a20>] (__lock_acquire+0x98c/0x19b
4)
[<80061094>] (__lock_acquire+0x0/0x19b4) from [<80062f14>] (lock_acquire+0x68/0x
7c)
[<80062eac>] (lock_acquire+0x0/0x7c) from [<80400f28>] (mutex_lock_nested+0x78/0
x344)
r7:00000000 r6:bf872000 r5:805cc858 r4:805c2a04
[<80400eb0>] (mutex_lock_nested+0x0/0x344) from [<803089ac>] (clk_get_rate+0x1c/
0x58)
[<80308990>] (clk_get_rate+0x0/0x58) from [<80013c48>] (twd_update_frequency+0x1
8/0x50)
r5:bf253d04 r4:805cadf4
[<80013c30>] (twd_update_frequency+0x0/0x50) from [<80068e20>] (generic_smp_call
_function_single_interrupt+0xd4/0x13c)
r4:bf873ee0 r3:80013c30
[<80068d4c>] (generic_smp_call_function_single_interrupt+0x0/0x13c) from [<80013
34c>] (handle_IPI+0xc0/0x194)
r8:00000001 r7:00000000 r6:80574e48 r5:bf872000 r4:80593958
[<8001328c>] (handle_IPI+0x0/0x194) from [<800084e8>] (gic_handle_irq+0x58/0x60)
r8:00000000 r7:bf873f8c r6:bf873f58 r5:80593070 r4:f4000100
r3:00000005
[<80008490>] (gic_handle_irq+0x0/0x60) from [<8000e124>] (__irq_svc+0x44/0x60)
Exception stack(0xbf873f58 to 0xbf873fa0)
3f40: 00000001 00000001
3f60: 00000000 bf814000 bf872000 805cab48 80405aa4 80597648 00000000 412fc09a
3f80: bf872000 bf873fac bf873f70 bf873fa0 80063844 8000f1f8 20000013 ffffffff
r6:ffffffff r5:20000013 r4:8000f1f8 r3:bf814000
[<8000f1b8>] (default_idle+0x0/0x4c) from [<8000f428>] (cpu_idle+0x98/0x114)
[<8000f390>] (cpu_idle+0x0/0x114) from [<803f9834>] (secondary_start_kernel+0x11
c/0x140)
[<803f9718>] (secondary_start_kernel+0x0/0x140) from [<103f9234>] (0x103f9234)
r6:10c03c7d r5:0000001f r4:4f86806a r3:803f921c
It looks that the warning is caused by that twd_update_frequency() gets
called from an atomic context while it calls clk_get_rate() where a
mutex gets held.
To fix the warning, let's convert common clk users over to clk notifiers
in place of CPUfreq notifiers. This works out nicely for Cortex-A9
MPcore designs that scale all CPUs at the same frequency.
Platforms that have not been converted to the common clk framework and
support CPUfreq will rely on the old mechanism. Once these platforms
are converted over fully then we can remove the CPUfreq-specific bits
for good.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Surprisingly devres_destroy() doesn't call the destructor for the
resource it is destroying, use the newly added devres_release() instead
to fix this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the old timestamps of a class, say cl, are stale when the class
becomes active, then QFQ may assign to cl a much higher start time
than the maximum value allowed. This may happen when QFQ assigns to
the start time of cl the finish time of a group whose classes are
characterized by a higher value of the ratio
max_class_pkt/weight_of_the_class with respect to that of
cl. Inserting a class with a too high start time into the bucket list
corrupts the data structure and may eventually lead to crashes.
This patch limits the maximum start time assigned to a class.
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
If recv() syscall is called for a TCP socket so that
- IOAT DMA is used
- MSG_WAITALL flag is used
- requested length is bigger than sk_rcvbuf
- enough data has already arrived to bring rcv_wnd to zero
then when tcp_recvmsg() gets to calling sk_wait_data(), receive
window can be still zero while sk_async_wait_queue exhausts
enough space to keep it zero. As this queue isn't cleaned until
the tcp_service_net_dma() call, sk_wait_data() cannot receive
any data and blocks forever.
If zero receive window and non-empty sk_async_wait_queue is
detected before calling sk_wait_data(), process the queue first.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some architectures test_bit() can return other values than 0 or 1:
With a generic x86 OpenWrt image in a kvm setup (batadv_)test_bit()
frequently returns -1 for me, leading to batadv_iv_ogm_update_seqnos()
wrongly signaling a protected seqno window.
This patch tries to fix this issue by making batadv_test_bit() return 0
or 1 only.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the initial domain we are able to search/map certain regions
of memory to harvest configuration data. For all low-level we
use ACPI tables - for interrupts we use exclusively ACPI _PRT
(so DSDT) and MADT for INT_SRC_OVR.
The SMP MP table is not used at all. As a matter of fact we do
not even support machines that only have SMP MP but no ACPI tables.
Lets follow how Moorestown does it and just disable searching
for BIOS SMP tables.
This also fixes an issue on HP Proliant BL680c G5 and DL380 G6:
9f->100 for 1:1 PTE
Freeing 9f-100 pfn range: 97 pages freed
1-1 mapping on 9f->100
.. snip..
e820: BIOS-provided physical RAM map:
Xen: [mem 0x0000000000000000-0x000000000009efff] usable
Xen: [mem 0x000000000009f400-0x00000000000fffff] reserved
Xen: [mem 0x0000000000100000-0x00000000cfd1dfff] usable
.. snip..
Scan for SMP in [mem 0x00000000-0x000003ff]
Scan for SMP in [mem 0x0009fc00-0x0009ffff]
Scan for SMP in [mem 0x000f0000-0x000fffff]
found SMP MP-table at [mem 0x000f4fa0-0x000f4faf] mapped at [ffff8800000f4fa0]
(XEN) mm.c:908:d0 Error getting mfn 100 (pfn 5555555555555555) from L1 entry 0000000000100461 for l1e_owner=0, pg_owner=0
(XEN) mm.c:4995:d0 ptwr_emulate: could not get_page_from_l1e()
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81ac07e2>] xen_set_pte_init+0x66/0x71
. snip..
Pid: 0, comm: swapper Not tainted 3.6.0-rc6upstream-00188-gb6fb969-dirty #2 HP ProLiant BL680c G5
.. snip..
Call Trace:
[<ffffffff81ad31c6>] __early_ioremap+0x18a/0x248
[<ffffffff81624731>] ? printk+0x48/0x4a
[<ffffffff81ad32ac>] early_ioremap+0x13/0x15
[<ffffffff81acc140>] get_mpc_size+0x2f/0x67
[<ffffffff81acc284>] smp_scan_config+0x10c/0x136
[<ffffffff81acc2e4>] default_find_smp_config+0x36/0x5a
[<ffffffff81ac3085>] setup_arch+0x5b3/0xb5b
[<ffffffff81624731>] ? printk+0x48/0x4a
[<ffffffff81abca7f>] start_kernel+0x90/0x390
[<ffffffff81abc356>] x86_64_start_reservations+0x131/0x136
[<ffffffff81abfa83>] xen_start_kernel+0x65f/0x661
(XEN) Domain 0 crashed: 'noreboot' set - not rebooting.
which is that ioremap would end up mapping 0xff using _PAGE_IOMAP
(which is what early_ioremap sticks as a flag) - which meant
we would get MFN 0xFF (pte ff461, which is OK), and then it would
also map 0x100 (b/c ioremap tries to get page aligned request, and
it was trying to map 0xf4fa0 + PAGE_SIZE - so it mapped the next page)
as _PAGE_IOMAP. Since 0x100 is actually a RAM page, and the _PAGE_IOMAP
bypasses the P2M lookup we would happily set the PTE to 1000461.
Xen would deny the request since we do not have access to the
Machine Frame Number (MFN) of 0x100. The P2M[0x100] is for example
0x80140.
CC: stable@vger.kernel.org
Fixes-Oracle-Bugzilla: https://bugzilla.oracle.com/bugzilla/show_bug.cgi?id=13665
Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Pull block fixes from Jens Axboe:
"A small collection of driver fixes/updates and a core fix for 3.6. It
contains:
- Bug fixes for mtip32xx, and support for new hardware (just addition
of IDs). They have been queued up for 3.7 for a few weeks as well.
- rate-limit a failing command error message in block core.
- A fix for an old cciss bug from Stephen.
- Prevent overflow of partition count from Alan."
* 'for-linus' of git://git.kernel.dk/linux-block:
cciss: fix handling of protocol error
blk: add an upper sanity check on partition adding
mtip32xx: fix user_buffer check in exec_drive_command
mtip32xx: Remove dead code
mtip32xx: Change printk to pr_xxxx
mtip32xx: Proper reporting of write protect status on big-endian
mtip32xx: Increase timeout for standby command
mtip32xx: Handle NCQ commands during the security locked state
mtip32xx: Add support for new devices
block: rate-limit the error message from failing commands
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBYK+cACgkQGkmNcg7/o7jthwCfemhnr590s3hwWXjA88ZZMFDl
U8kAoJA7hNCtAqdoj+LHXJlKLK1UalkD
=aCxD
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Fix up TIF_NOTIFY_RESUME sans TIF_SIGPENDING handling.
sh: pfc: Release spinlock in sh_pfc_gpio_request_enable() error path
sh: intc: Fix up multi-evt irq association.
One reverts a recent patch which turns out to not be such a good
idea.
Other two fix minor bugs with the new (since 3.3) 'replacement' code
and have been tagged for -stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=dfcj
-----END PGP SIGNATURE-----
Merge tag 'md-3.6-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"3 fixes for md in 3.6.
One reverts a recent patch which turns out to not be such a good idea.
Other two fix minor bugs with the new (since 3.3) 'replacement' code
and have been tagged for -stable."
* tag 'md-3.6-fixes' of git://neil.brown.name/md:
md: make sure metadata is updated when spares are activated or removed.
md/raid5: fix calculate of 'degraded' when a replacement becomes active.
Revert "md/raid5: For odirect-write performance, do not set STRIPE_PREREAD_ACTIVE."
Pull workqueue / powernow-k8 fix from Tejun Heo:
"This is the fix for the bug where cpufreq/powernow-k8 was tripping
BUG_ON() in try_to_wake_up_local() by migrating workqueue worker to a
different CPU.
https://bugzilla.kernel.org/show_bug.cgi?id=47301
As discussed, the fix is now two parts - one to reimplement
work_on_cpu() so that it doesn't create a new kthread each time and
the actual fix which makes powernow-k8 use work_on_cpu() instead of
performing manual migration.
While pretty late in the merge cycle, both changes are on the safer
side. Jiri and I verified two existing users of work_on_cpu() and
Duncan confirmed that the powernow-k8 fix survived about 18 hours of
testing."
* 'for-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
cpufreq/powernow-k8: workqueue user shouldn't migrate the kworker to another CPU
workqueue: reimplement work_on_cpu() using system_wq
This reverts commit ca3b3faf9b.
There was a plan to place ab8500_irq_get_virq() calls in each AB8500
child device prior to requesting an IRQ, but as we're no longer using
Device Tree to collect our IRQ numbers, it's actually better to allow
the core to do this during device registration time. So the IRQ number
we pull from its resource has already been converted to a virtual IRQ.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQS9hEAAoJEHm+PkMAQRiGo04H/0UmrnxfD6NLS8SGE8EOqbn+
d2kSVcLxvpBAOSg6chvNgxnUoohL3Or4LpagqLSsfAYgLBmGw8lPEEOFJ3MMXhsd
/YYJti2Hyke0zFfbW3ZxUmL1d+DFopqgjLeDLsabcTuL9ksVkA5tOeIwyEVZb9k0
8Uwh4ejscKHdNUZXMWB6DQoxnDFwlgdz+/n8Bj/v7w71suvIxSWSo2A7TtfVhMsz
34uifzaawhs8bldpHkRuuo6+YSNs+ozhVFcz8aT/zf7egDjCfuVA098Te28k2PKS
LMQs9uDpXEJ3jE7/bb4O9iSc0+ZlBLz5c3XDj5ijqjdC3Us8Na6dRB0eu3Wdb+o=
=KJIJ
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc5' into for-linus
Sync with mainline so that I can revert an input patch that came in through
another subsystem tree.
powernowk8_target() runs off a per-cpu work item and if the
cpufreq_policy->cpu is different from the current one, it migrates the
kworker to the target CPU by manipulating current->cpus_allowed. The
function migrates the kworker back to the original CPU but this is
still broken. Workqueue concurrency management requires the kworkers
to stay on the same CPU and powernowk8_target() ends up triggerring
BUG_ON(rq != this_rq()) in try_to_wake_up_local() if it contends on
fidvid_mutex and sleeps.
It is unclear why this bug is being reported now. Duncan says it
appeared to be a regression of 3.6-rc1 and couldn't reproduce it on
3.5. Bisection seemed to point to 63d95a91 "workqueue: use @pool
instead of @gcwq or @cpu where applicable" which is an non-functional
change. Given that the reproduce case sometimes took upto days to
trigger, it's easy to be misled while bisecting. Maybe something made
contention on fidvid_mutex more likely? I don't know.
This patch fixes the bug by using work_on_cpu() instead if @pol->cpu
isn't the same as the current one. The code assumes that
cpufreq_policy->cpu is kept online by the caller, which Rafael tells
me is the case.
stable: ed48ece27c ("workqueue: reimplement work_on_cpu() using
system_wq") should be applied before this; otherwise, the
behavior could be horrible.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Duncan <1i5t5.duncan@cox.net>
Tested-by: Duncan <1i5t5.duncan@cox.net>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: stable@vger.kernel.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47301
The existing work_on_cpu() implementation is hugely inefficient. It
creates a new kthread, execute that single function and then let the
kthread die on each invocation.
Now that system_wq can handle concurrent executions, there's no
advantage of doing this. Reimplement work_on_cpu() using system_wq
which makes it simpler and way more efficient.
stable: While this isn't a fix in itself, it's needed to fix a
workqueue related bug in cpufreq/powernow-k8. AFAICS, this
shouldn't break other existing users.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@vger.kernel.org
This patch updates the existing Intel IvyBridge (model 58)
support with proper PEBS event constraints. It cannot reuse
the same as SandyBridge because some events (0xd3) are
specific to IvyBridge.
Also there is no UOPS_DISPATCHED.THREAD on IVB, so do not
populate the PERF_COUNT_HW_STALLED_CYCLES_BACKEND mapping.
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: peterz@infradead.org
Cc: ak@linux.intel.com
Link: http://lkml.kernel.org/r/20120910230701.GA5898@quad
Signed-off-by: Ingo Molnar <mingo@kernel.org>
After commit b6d86d3d (Fix DIV_ROUND_CLOSEST to support negative dividends),
the following warning is seen if the kernel is compiled with W=1 (-Wextra):
warning: comparison of unsigned expression >= 0 is always true
The warning is due to the test '((typeof(x))-1) >= 0', which is used to detect
if the variable type is unsigned. Research on the web suggests that the warning
disappears if '>' instead of '>=' is used for the comparison.
Tests after changing the macro along that line show that the warning is gone,
and that the result is still correct:
i=-4: DIV_ROUND_CLOSEST(i, 2)=-2
i=-3: DIV_ROUND_CLOSEST(i, 2)=-2
i=-2: DIV_ROUND_CLOSEST(i, 2)=-1
i=-1: DIV_ROUND_CLOSEST(i, 2)=-1
i=0: DIV_ROUND_CLOSEST(i, 2)=0
i=1: DIV_ROUND_CLOSEST(i, 2)=1
i=2: DIV_ROUND_CLOSEST(i, 2)=1
i=3: DIV_ROUND_CLOSEST(i, 2)=2
i=4: DIV_ROUND_CLOSEST(i, 2)=2
Code size is the same as before.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
It isn't always necessary to update the metadata when spares are
removed as the presence-or-not of a spare isn't really important to
the integrity of an array.
Also activating a spare doesn't always require updating the metadata
as the update on 'recovery-completed' is usually sufficient.
However the introduction of 'replacement' devices have made these
transitions sometimes more important. For example the 'Replacement'
flag isn't cleared until the original device is removed, so we need
to ensure a metadata update after that 'spare' is removed.
So set MD_CHANGE_DEVS whenever a spare is activated or removed, to
complement the current situation where it is set when a spare is added
or a device is failed (or a number of other less common situations).
This is suitable for -stable as out-of-data metadata could lead
to data corruption.
This is only relevant for 3.3 and later 9when 'replacement' as
introduced.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When a replacement device becomes active, we mark the device that it
replaces as 'faulty' so that it can subsequently get removed.
However 'calc_degraded' only pays attention to the primary device, not
the replacement, so the array appears to become degraded, which is
wrong.
So teach 'calc_degraded' to consider any replacement if a primary
device is faulty.
This is suitable for -stable as an incorrect 'degraded' value can
confuse md and could lead to data corruption.
This is only relevant for 3.3 and later.
Cc: stable@vger.kernel.org
Reported-by: Robin Hill <robin@robinhill.me.uk>
Reported-by: John Drescher <drescherjm@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This reverts commit 895e3c5c58.
While this patch seemed like a good idea and did help some workloads,
it hurts other workloads.
Large sequential O_DIRECT writes were faster,
Small random O_DIRECT writes were slower.
Other changes (batching RAID5 writes) have improved the sequential
writes using a different mechanism, so the net result of this patch
is definitely negative. So revert it.
Reported-by: Shaohua Li <shli@kernel.org>
Tested-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When the driver can't get the HW ready, we would release
the interrupt twice which made the kernel complain loudly.
Cc: stable@vger.kernel.org
Reported-by: Brian Cockrell <brian.cockrell@intel.com>
Tested-by: Brian Cockrell <brian.cockrell@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When call_crda() is called we kick off a witch hunt search
for the same regulatory domain on our internal regulatory
database and that work gets kicked off on a workqueue, this
is done while the cfg80211_mutex is held. If that workqueue
kicks off it will first lock reg_regdb_search_mutex and
later cfg80211_mutex but to ensure two CPUs will not contend
against cfg80211_mutex the right thing to do is to have the
reg_regdb_search() wait until the cfg80211_mutex is let go.
The lockdep report is pasted below.
cfg80211: Calling CRDA to update world regulatory domain
======================================================
[ INFO: possible circular locking dependency detected ]
3.3.8 #3 Tainted: G O
-------------------------------------------------------
kworker/0:1/235 is trying to acquire lock:
(cfg80211_mutex){+.+...}, at: [<816468a4>] set_regdom+0x78c/0x808 [cfg80211]
but task is already holding lock:
(reg_regdb_search_mutex){+.+...}, at: [<81646828>] set_regdom+0x710/0x808 [cfg80211]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (reg_regdb_search_mutex){+.+...}:
[<800a8384>] lock_acquire+0x60/0x88
[<802950a8>] mutex_lock_nested+0x54/0x31c
[<81645778>] is_world_regdom+0x9f8/0xc74 [cfg80211]
-> #1 (reg_mutex#2){+.+...}:
[<800a8384>] lock_acquire+0x60/0x88
[<802950a8>] mutex_lock_nested+0x54/0x31c
[<8164539c>] is_world_regdom+0x61c/0xc74 [cfg80211]
-> #0 (cfg80211_mutex){+.+...}:
[<800a77b8>] __lock_acquire+0x10d4/0x17bc
[<800a8384>] lock_acquire+0x60/0x88
[<802950a8>] mutex_lock_nested+0x54/0x31c
[<816468a4>] set_regdom+0x78c/0x808 [cfg80211]
other info that might help us debug this:
Chain exists of:
cfg80211_mutex --> reg_mutex#2 --> reg_regdb_search_mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(reg_regdb_search_mutex);
lock(reg_mutex#2);
lock(reg_regdb_search_mutex);
lock(cfg80211_mutex);
*** DEADLOCK ***
3 locks held by kworker/0:1/235:
#0: (events){.+.+..}, at: [<80089a00>] process_one_work+0x230/0x460
#1: (reg_regdb_work){+.+...}, at: [<80089a00>] process_one_work+0x230/0x460
#2: (reg_regdb_search_mutex){+.+...}, at: [<81646828>] set_regdom+0x710/0x808 [cfg80211]
stack backtrace:
Call Trace:
[<80290fd4>] dump_stack+0x8/0x34
[<80291bc4>] print_circular_bug+0x2ac/0x2d8
[<800a77b8>] __lock_acquire+0x10d4/0x17bc
[<800a8384>] lock_acquire+0x60/0x88
[<802950a8>] mutex_lock_nested+0x54/0x31c
[<816468a4>] set_regdom+0x78c/0x808 [cfg80211]
Reported-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For example, when a usb reset is received (I could reproduce it
running something very similar to this[1] in a loop) it could be
that the device is unregistered while the power_off delayed work
is still scheduled to run.
Backtrace:
WARNING: at lib/debugobjects.c:261 debug_print_object+0x7c/0x8d()
Hardware name: To Be Filled By O.E.M.
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x26
Modules linked in: nouveau mxm_wmi btusb wmi bluetooth ttm coretemp drm_kms_helper
Pid: 2114, comm: usb-reset Not tainted 3.5.0bt-next #2
Call Trace:
[<ffffffff8124cc00>] ? free_obj_work+0x57/0x91
[<ffffffff81058f88>] warn_slowpath_common+0x7e/0x97
[<ffffffff81059035>] warn_slowpath_fmt+0x41/0x43
[<ffffffff8124ccb6>] debug_print_object+0x7c/0x8d
[<ffffffff8106e3ec>] ? __queue_work+0x259/0x259
[<ffffffff8124d63e>] ? debug_check_no_obj_freed+0x6f/0x1b5
[<ffffffff8124d667>] debug_check_no_obj_freed+0x98/0x1b5
[<ffffffffa00aa031>] ? bt_host_release+0x10/0x1e [bluetooth]
[<ffffffff810fc035>] kfree+0x90/0xe6
[<ffffffffa00aa031>] bt_host_release+0x10/0x1e [bluetooth]
[<ffffffff812ec2f9>] device_release+0x4a/0x7e
[<ffffffff8123ef57>] kobject_release+0x11d/0x154
[<ffffffff8123ed98>] kobject_put+0x4a/0x4f
[<ffffffff812ec0d9>] put_device+0x12/0x14
[<ffffffffa009472b>] hci_free_dev+0x22/0x26 [bluetooth]
[<ffffffffa0280dd0>] btusb_disconnect+0x96/0x9f [btusb]
[<ffffffff813581b4>] usb_unbind_interface+0x57/0x106
[<ffffffff812ef988>] __device_release_driver+0x83/0xd6
[<ffffffff812ef9fb>] device_release_driver+0x20/0x2d
[<ffffffff813582a7>] usb_driver_release_interface+0x44/0x7b
[<ffffffff81358795>] usb_forced_unbind_intf+0x45/0x4e
[<ffffffff8134f959>] usb_reset_device+0xa6/0x12e
[<ffffffff8135df86>] usbdev_do_ioctl+0x319/0xe20
[<ffffffff81203244>] ? avc_has_perm_flags+0xc9/0x12e
[<ffffffff812031a0>] ? avc_has_perm_flags+0x25/0x12e
[<ffffffff81050101>] ? do_page_fault+0x31e/0x3a1
[<ffffffff8135eaa6>] usbdev_ioctl+0x9/0xd
[<ffffffff811126b1>] vfs_ioctl+0x21/0x34
[<ffffffff81112f7b>] do_vfs_ioctl+0x408/0x44b
[<ffffffff81208d45>] ? file_has_perm+0x76/0x81
[<ffffffff8111300f>] sys_ioctl+0x51/0x76
[<ffffffff8158db22>] system_call_fastpath+0x16/0x1b
[1] http://cpansearch.perl.org/src/DPAVLIN/Biblio-RFID-0.03/examples/usbreset.c
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When releasing L2CAP socket which is in BT_CONFIG state l2cap_chan_close
invokes l2cap_send_disconn_req which cancel delayed works which are only
set in BT_CONNECTED state with l2cap_ertm_init. Add state check before
cancelling those works.
...
[ 9668.574372] [21085] l2cap_sock_release: sock cd065200, sk f073e800
[ 9668.574399] [21085] l2cap_sock_shutdown: sock cd065200, sk f073e800
[ 9668.574411] [21085] l2cap_chan_close: chan f073ec00 state BT_CONFIG sk f073e800
[ 9668.574421] [21085] l2cap_send_disconn_req: chan f073ec00 conn ecc16600
[ 9668.574441] INFO: trying to register non-static key.
[ 9668.574443] the code is fine but needs lockdep annotation.
[ 9668.574446] turning off the locking correctness validator.
[ 9668.574450] Pid: 21085, comm: obex-client Tainted: G O 3.5.0+ #57
[ 9668.574452] Call Trace:
[ 9668.574463] [<c10a64b3>] __lock_acquire+0x12e3/0x1700
[ 9668.574468] [<c10a44fb>] ? trace_hardirqs_on+0xb/0x10
[ 9668.574476] [<c15e4f60>] ? printk+0x4d/0x4f
[ 9668.574479] [<c10a6e38>] lock_acquire+0x88/0x130
[ 9668.574487] [<c1059740>] ? try_to_del_timer_sync+0x60/0x60
[ 9668.574491] [<c1059790>] del_timer_sync+0x50/0xc0
[ 9668.574495] [<c1059740>] ? try_to_del_timer_sync+0x60/0x60
[ 9668.574515] [<f8aa1c23>] l2cap_send_disconn_req+0xe3/0x160 [bluetooth]
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Ira W. Snyder