Starting from ILK, mmio flips also cause a flip done interrupt to be
signalled. This means if we first do a set_base and follow it
immediately with the CS flip, we might mistake the flip done interrupt
caused by the set_base as the flip done interrupt caused by the CS
flip.
The hardware has a flip counter which increments every time a mmio or
CS flip is issued. It basically counts the number of DSPSURF register
writes. This means we can sample the counter before we put the CS
flip into the ring, and then when we get a flip done interrupt we can
check whether the CS flip has actually performed the surface address
update, or if the interrupt was caused by a previous but yet
unfinished mmio flip.
Even with the flip counter we still have a race condition of the CS flip
base address update happens after the mmio flip done interrupt was
raised but not yet processed by the driver. When the interrupt is
eventually processed, the flip counter will already indicate that the
CS flip has been executed, but it would not actually complete until the
next start of vblank. We can use the DSPSURFLIVE register to check
whether the hardware is actually scanning out of the buffer we expect,
or if we managed hit this race window.
This covers all the cases where the CS flip actually changes the base
address. If the base address remains unchanged, we might still complete
the CS flip before it has actually completed. But since the address
didn't change anyway, the premature flip completion can't result in
userspace overwriting data that's still being scanned out.
CTG already has the flip counter and DSPSURFLIVE registers, and
although the flip done interrupt is still limited to CS flips alone,
the code now also checks the flip counter on CTG as well.
v2: s/dspsurf/gtt_offset/ (Chris)
Testcase: igt/kms_mmio_vs_cs_flip/setcrtc_vs_cs_flip
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73027
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add g4x_ prefix to flip_count_after_eq.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The comments in i915_reg.h aren't proper kernel-doc comments, so replace
the magic /** with just /*
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The following workarounds should be needed for pre-production hardware
only:
* WaDisablePwrmtrEvent:chv
* WaSetMaskForGfxBusyness:chv
* WaDisableGunitClockGating:chv
* WaDisableFfDopClockGating:chv
* WaDisableDopClockGating:chv
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec only tells us to set individual bits here and there. So we use
RMW for most things. Do the same for the swing calc init.
Eventually we should optimize things to just blast the final value in
with group access whenever possible. But to do that someone needs to
take a good look at what's the reset value for each registers, and
possibly if the BIOS manages to frob with some of them. For now
use RMW access always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like PCS, TX group reads return 0xffffffff. So we need to target each
lane separately if we want to use RMW cycles to update the registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All PCS groups access reads return 0xffffffff, so we can't use group
access for RMW cycles. Instead target each spline separately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Fight conflict with misplaced ; .... ARGH!]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bits we've been setting so far only progagate the reset singal to
the data lanes. To actaully force the reset signal we need to set another
override bit.
v2: Fix mispalced ';' (Mika)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the encoder .get_config hooks to report the correct active pipe for
CHV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unsurprisingly the cursor C regiters are also at a weird offset on CHV.
Add more pipe offsets to handle them.
This also gets rid of most of the differences between the i9xx vs. ivb
cursor code. We can unify the remaining code as well, but I'll leave
that for another patch.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On CHV the GMBUS port for port D is different from other gmch platforms
which have port D. Fix it up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for the third pipe in cherrview
v2: Don't use spaces for indentation (Jani)
Wrap long lines
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
[vsyrjala: slightly massaged the patch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're using the reset domains bits for g4x on ilk. But on ilk those bits
actually shifted by one bit. Fix it up so that we use the correct bits.
We were actually always writing 0x2 to the reset domain bits, which
is a reserved value. In practice it looks like the hardware ignores that
value since nothing happens if I write that value when there's a 3D
workload running. Writing the _correct_ render domain value actually
makes the GPU stop.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds a mmio base address variable for DSI display,
to make the DSI code generic, so that, if required, the same code
can be re-used for future platforms with different mmio base.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These opcodes are not specific for an endpoint, but are the same for all
endpoints. So rename them accordingly, using the name the VLV2 sideband
HAS uses. Also move the macros to the .c file, since they aren't used
anywhere else.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In BDW, Apart from unmasking up/down threshold interrupts. we need
to umask bit 32 of PM_INTRMASK to route interrupts to target via Display
Interface.
v2: Add (1<<31) mask (Ville)
v3: Add Gen check for the mask (ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Almost all of it is reusable from the existing code. The primary
difference is we need to do even less in the interrupt handler, since
interrupts are not shared in the same way.
The patch is mostly a copy-paste of the existing snb+ code, with updates
to the relevant parts requiring changes to the interrupt handling. As
such it /should/ be relatively trivial. It's highly likely that I missed
some places where I need a gen8 version of the PM interrupts, but it has
become invisible to me by now.
This patch could probably be split into adding the new functions,
followed by actually handling the interrupts. Since the code is
currently disabled (and broken) I think the patch stands better by
itself.
v2: Move the commit about not touching the ringbuffer interrupt to the
snb_* function where it belongs (Rodrigo)
v3: Rebased on Paulo's runtime PM changes
v4: Not well validated, but rebase on
commit 730488b2ed
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Mar 7 20:12:32 2014 -0300
drm/i915: kill dev_priv->pm.regsave
v5: Rebased on latest code base. (Deepak)
v6: Remove conflict markers, Unnecessary empty line and use right
IIR interrupt (Ville)
v7: mask modified without rmw (Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With additional of pipe C, current 1 bit registers for pipe select
for HDMI and DP are no longer able to gather for 3 pipes. As a result,
new bits location in the same registers are added.
For HDMI, VLV uses bit 30, CHV uses bit 24-25.
For DP, VLV uses bit 30, CHV uses bit 16-17.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added programming PLL for CHV based on "Application note for 1273 CHV
Display phy".
v2: -Break the common lane reset into another patch.
-Break the clock calculation into another patch.
-The changes are based on Ville review.
-Rework based on DPIO register define naming convention change.
-Break the dpio write into few lines to improve readability.
-Correct the udelay during chv_enable_pll.
-clean up some magic numbers with some new define.
-program the afc recal bit which was missed.
v3: Based on Ville review
- minor correction of the bit defination
- add deassert/propagate data lane reset
v4: Corrected the udelay between dclkp enable and pll enable.
Minor comment and better way to clear the TX lane reset.
v5: Squash in fixup from Rafael Barbalho.
[vsyrjala: v6: Polish the defines (Imre)]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During cold boot, the display controller needs to deassert the common
lane reset. Only do it once during intel_init_dpio for both PHYx2 and
PHYx1.
Besides, assert the common lane reset when disable pll. This still
to be determined whether need to do it by driver.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[vsyrjala: Don't disable DPIO PLL when using DSI]
[vsyrjala: Don't call vlv_disable_pll() by accident on CHV]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Move part of a moved comment back as suggested by Imre since
it's valid for both byt and chv.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The additional DPLL registers added to support Port D. Besides, add
some new PHY control and status registers based on B-spec.
v2: Based on Ville review
- Corrected DPIO_PHY_STATUS offset and name.
- Rebase based on upstream change after introduce enum dpio_phy and
enum dpio_channel.
v3: Rebased on top of Antti's 3-pipe prep patch. Note that the new offsets for
the DPLL registers aren't in place yet, so this introduces a slight regression.
But since 3 pipe support isn't fully enabled yet anyaway in -internal this
shouldn't matter too much.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has 2 display phys. First phy (IOSF offset 0x1A) has two channels,
and second phy (IOSF offset 0x12) has single channel. The first phy is
used for port B and port C, while second phy is only for port D.
v2: Move the pipe to determine which phy to select for
vlv_dpio_read/vlv_dpio_write to another patch. (Daniel)
v3: Rebase the code based on rework on how to calculate DPIO offset.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fill in the sprite bits for DDL1/DDL2 registers, and add DDL3.
Still need to write the code to use these...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Needed by the VLV S0ix context save/restore helpers.
v2:
- unchanged
v3:
- use proper GEN register prefixes (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Due to Pipe C DPINVGTT has more bits on CHV.
v2: Fix comment to say VLV/CHV (Rafael)
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebase on top of Ben's GT interrupt shuffling.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has pipe C and PSR which cause changes to DPFLIPSTAT.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIXME: We probably want to sprinkle _CHV suffixes over these.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These will be needed by the upcoming VLV RPM helpers.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the hardware spec, the BDW GT3 machine has two independent
BSD ring that can be used to dispatch the video commands.
So just initialize it.
V3->V4: Follow Imre's comment to do some minor updates. For example:
more comments are added to describe the semaphore between ring.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
[danvet: Fix up checkpatch error.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch computes and stored 2nd M/N/TU for switching to different
refresh rate dynamically. PIPECONF_EDP_RR_MODE_SWITCH bit helps toggle
between alternate refresh rates programmed in 2nd M/N/TU registers.
v2: Daniel's review comments
Computing M2/N2 in compute_config and storing it in crtc_config
v3: Modified reference to edp_downclock and edp_downclock_avail based on the
changes made to move them from dev_private to intel_panel.
v4: Modified references to is_drrs_supported based on the changes made to
rename it to drrs_support.
v5: Jani's review comments
Removed superfluous return statements. Changed support for Gen 7 and above.
Corrected indentation. Re-structured the code which finds crtc and connector
from encoder. Changed some logs to be less verbose.
v6: Modifying i915_drrs to include only intel connector as intel_dp can be
derived from intel connector when required.
v7: As per internal review comments, acquiring mutex just before accessing
drrs RR. As per Chris's review comments, added documentation about the use
of locking in the function.
v8: Incorporated Jani's review comments.
Removed reference to edp_downclock.
v9: Jani's review comments. Modified comment in set_drrs. Changed index to
type edp_drrs_refresh_rate_type. Check if PSR is enabled before setting
registers fo DRRS.
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are additional registers needed for performance monitoring and
ARB_draw_indirect extensions in mesa.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76719
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Squash in fixup from Brad requested by Ken.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is now clear that this interrupt is for the primary plane and not
something global to the pipe. It also matches what the spec calls it.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN8 now has a qword to code for 48bit addresses.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems like it wouldn't be too unlikely to be wanting to use a an
expression in the macro argument and things could go very wrong.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Gen4+ platforms (except BDW), Render Cache Operational flush
cannot be enabled.
This WA is apparently required for all Gen4+ platforms,except BDW.
In BDW, the bit has been repurposed otherwise.
This has been tested only on vlv.
v2: Corrected the code regarding the wrong usage of
MASKED_BIT_DISABLE (Chris)
v3: Enhancing the scope of WA to Gen4+ platforms except BDW (Ville)
v4: Adding WA for g4x, crestline, broadwater (Ville)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sourab Gupta <sourab.gupta@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In commit a51435a313
Author: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Date: Wed Mar 12 16:39:40 2014 +0530
drm/i915: disable rings before HW status page setup
we reordered stopping the rings to do so before we set the HWS register.
However, there is an extra workaround for g45 to reset the rings twice,
and for consistency we should apply that workaround before setting the
HWS to be sure that the rings are truly stopped.
Cc: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The framecount register was still using the old PIPE macro instead
of the new PIPE2 macro
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For error state, like the recent modification to ACTHD, FADD also gets
an upper dword. This is useful for debug to make sure the fetch address
and head are similar.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mesa needs to be able to write OACONTROL in order to expose the
Observability Architecture's performance counters via OpenGL.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Add comment that this is just a temporary work-around and
that we need to check more things before we can allow OACONTROL writes
for real everywhere.]
[danvet 2: Squash in fixup to avoid a DRM_ERROR due to unsorted reg
list, spotted by Jani.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PIPE_CONTROL and MI_FLUSH_DW have bits that would write to the
hardware status page. The driver stores request tracking info
there, so don't let userspace overwrite it.
v2: trailing comma fix, rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Various commands that access memory have a bit to determine whether
the graphics address specified in the command should use the GGTT or
PPGTT for translation. These checks ensure that the bit indicates
PPGTT translation.
Most of these checks use the existing bit-checking infrastructure.
The PIPE_CONTROL and MI_FLUSH_DW commands, however, are multi-function
commands. The GGTT/PPGTT bit is only relevant for certain uses of the
command. As such, this change also extends the bit-checking code to
include a "condition" mask and offset. If the condition mask is non-zero
then the parser only performs the bit check when the bits specified by
the condition mask/offset are also non-zero.
NOTE: At this point in the series PPGTT must be enabled for the parser
to work correctly. If it's not enabled, userspace will not be setting
the PPGTT bits the way the parser requires. VLV is the only platform
where this is a problem, so at this point, we disable parsing for VLV.
v2: whitespace and trailing commas fixes, rebased
OTC-Tracker: AXIA-4631
Change-Id: I3f4c76b6734f1956ec47e698230f97d0998ff92b
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop the unecessary cast Jani spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The driver leaves most interrupts masked during normal operation,
so there would have to be additional work to enable userspace to
safely request/receive an interrupt.
v2: trailing commas, rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
MI_STORE_REGISTER_MEM, MI_LOAD_REGISTER_MEM, and MI_LOAD_REGISTER_IMM
commands allow userspace access to registers. Only certain registers
should be allowed for such access, so enable checking for those commands.
Each ring gets its own register whitelist.
MI_LOAD_REGISTER_REG on HSW also allows register access but is currently
unused by userspace components. Leave it rejected.
PIPE_CONTROL and MEDIA_VFE_STATE allow register access based on certain
bits being set. Reject those as well.
v2: trailing commas, rebased
OTC-Tracker: AXIA-4631
Change-Id: Ie614a2f0eb2e5917de809e5a17957175d24cc44f
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are used to implement scanline waits in the X server.
v2: Use #defines instead of magic numbers
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These registers are currently used by mesa for blitting,
transform feedback extensions, and performance monitoring
extensions.
v2: REG64 macro
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec defines most of these commands as privileged. A few others,
like the semaphore mbox command and some display commands, are also
reserved for the driver's use. Subsequent patches relax some of
these restrictions.
v2: Rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add command tables defining irregular length commands for each ring.
This requires a few new command opcode definitions.
v2: Whitespace adjustment in command definitions, sparse fix for !F
OTC-Tracker: AXIA-4631
Change-Id: I064bceb457e15f46928058352afe76d918c58ef5
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently not an issue since we don't emit sempahores, but better
not forget about those.
As a little prep work extract the ipehr decoding for cleaner control
flow. And apply a bit of polish.
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The documentation calls this GFX_MODE bit "Flush TLB invalidate Mode".
However, that is not a good name for an enable bit as it doesn't make it
clear what is enabled. An even worse name is GFX_TLB_INVALIDATE_ALWAYS
as enabling that bit actually prevents the TLB from being invalidated at
every flush. This leads to great confusion when reading code and
proposed patches. To get around this try to bake in what is enabled by
setting the bit and call it GFX_TLB_INVALIDATE_EXPLICIT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Gupta, Sourab" <sourab.gupta@intel.com>
Acked-by: "Gupta, Sourab" <sourab.gupta@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As Broadwell has an increased virtual address size, it requires more
than 32 bits to store offsets into its address space. This includes the
debug registers to track the current HEAD of the individual rings, which
may be anywhere within the per-process address spaces. In order to find
the full location, we need to read the high bits from a second register.
We then also need to expand our storage to keep track of the larger
address.
v2: Carefully read the two registers to catch wraparound between
the reads.
v3: Use a WARN_ON rather than loop indefinitely on an unstable
register read.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Drop spurious hunk which conflicted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not implementing this W/A can lead to hangs.
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Rafael Barbalho <rafael.barbalho@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this patch we allow larger cursor planes of sizes 128x128
and 256x256.
v2: Added more precise check on size while setting cursor plane.
v3: Changes related to restructuring cursor size restrictions
and DRM_DEBUG usage.
v4: Indentation related changes for setting cursor control and
implementing DRM_CAP_CURSOR_WIDTH and DRM_CAP_CURSOR_HEIGHT
Testcase: igt/kms_cursor_crc
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: G, Pallavi <pallavi.g@intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
make sure we wait for rings to become idle once they are
disabled. In case of timeout print an error message
Signed-off-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
[danvet: Frob patch as suggested by Chris.]
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The command parser scans batch buffers submitted via execbuffer ioctls before
the driver submits them to hardware. At a high level, it looks for several
things:
1) Commands which are explicitly defined as privileged or which should only be
used by the kernel driver. The parser generally rejects such commands, with
the provision that it may allow some from the drm master process.
2) Commands which access registers. To support correct/enhanced userspace
functionality, particularly certain OpenGL extensions, the parser provides a
whitelist of registers which userspace may safely access (for both normal and
drm master processes).
3) Commands which access privileged memory (i.e. GGTT, HWS page, etc). The
parser always rejects such commands.
See the overview comment in the source for more details.
This patch only implements the logic. Subsequent patches will build the tables
that drive the parser.
v2: Don't set the secure bit if the parser succeeds
Fail harder during init
Makefile cleanup
Kerneldoc cleanup
Clarify module param description
Convert ints to bools in a few places
Move client/subclient defs to i915_reg.h
Remove the bits_count field
OTC-Tracker: AXIA-4631
Change-Id: I50b98c71c6655893291c78a2d1b8954577b37a30
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the upcoming patches we'll need to access the rest of the fields in
the punit power gating register, so prepare for that.
v2:
- add doc reference for the power well subsystem IDs (Jesse)
- remove IDs for non-existant DPIO_RX[23] subsystems (Jesse)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have two names for the same register CHICKEN_PIPESL_1 and
HSW_PIPE_SLICE_CHICKEN_1. Unify it to just one.
Also rename the FBCQ disable bit to resemble the name we've
given to a similar bit on earlier platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to BSpec we need to always set this magic bit in ring buffer
mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben and I believe this will be necessary on production hardware.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Shuffle lines to group all ROW_CHICKEN writes and add a
cautious comment that this might not be needed on production hw.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I believe this will be necessary on production hardware.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Fix whitespace fail spotted by checkpatch. Also add missing
:bdw w/a tag that Ville spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In commit e4e0c058a1
Author: Eugeni Dodonov <eugeni.dodonov@intel.com>
Date: Wed Feb 8 12:53:50 2012 -0800
drm/i915: gen7: Implement an L3 caching workaround.
the L3 cache aging was disabled. This was part of a shotgun response
to a number of GPU hang bugs, but there appears to be no documentation
to suggest that disabling the L3 cache age was ever required (to prevent
the GPU hangs).
Restoring the L3 cache age is a minor performance win of around 2%
on IVB:GT2. (Note that this value seems to be consistent across a number
of tests and so appears to be above the usual noise.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BSpec recommends using 8x4 hashing mode when MSAA is used. But in
practice 16x4 seems to have a slight edge in performance (on IVB and
HSW at least). So just use 16x4.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SNB we set up WaSetupGtModeTdRowDispatch:snb early in
gen6_init_clock_gating(). That sets a bit in the GEN6_GT_MODE register.
However later we go and disable all the bits in the same register. And
then we go on to set some other bit. So apparently we never actually
implemented this workaround since the "disable all bits" part was there
already before the w/a got supposedly implemented.
These are the relevant commits:
commit 6547fbdbff
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Dec 14 23:38:29 2012 +0100
drm/i915: Implement WaSetupGtModeTdRowDispatch
commit f8f2ac9a76
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Wed Oct 3 19:34:24 2012 -0700
drm/i915: Fix GT_MODE default value
So, let's drop the "disable all bits" part, move both writes to
closer proxomity to each other, and name the WIZ hashing bits
appropriately. BSpec is still a bit confused how the bits should
actually be interpreted, but I took the the description for the
high bit since the low bit part only lists values for a single bit.
Also add a comment about our choice of WIZ hashing mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a couple of switch cases to compute the port value for the
VIDEO_DIP_CTL register. Replace them with a simple macro.
We do lose a few BUG() calls, but many people may consider that
an improvement.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just a bit of polish which I hope will help me with massaging some
internal patches to use Imre's reworked pipestat handling:
- Don't check for underrun reporting or enable pipestat interrupts
twice.
- Frob the comments a bit.
- Do the iir PIPE_EVENT to pipe mapping explicitly with a switch. We
only have one place which does this, so better to make it explicit.
v2: Ville noticed that I've broken the logic a bit with trying to
avoid checking whether we're interested in a given pipe twice. push
the PIPESTAT read down after we've computed the mask of interesting
bits first to avoid that duplication properly.
v3: Squash in fixups from Imre on irc.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FUSE_STRAP has a bit to inform us that the display has been fused off.
Use it to setup the definitive number of pipes at run-time.
v2: actually tweak num_pipes, not num_planes
v3: also tests SFUSE_STRAP bit 7
v4: rebase on top of drm-nightly
use DRM_INFO() for the message telling display is fused off
try to read the FUSE_LOCK bit to determine if PCH display is disabled
v5: Don't read SFUSE_STRAP (register on the PCH) if num_pipes is already 0
from the initial device info struct (to prevent hangs) (Daniel Vetter)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> (for v3)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (for v3)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we call the handlers for pending pipestat interrupt events even if
they aren't explicitly enabled by i915_enable_pipestat(). This isn't an
issue for events other than the vblank start event, since those are
always enabled anyways. Otoh, we enable the vblank start event
on-demand, so we'll end up calling the vblank handler at times when they
are disabled.
I haven't checked if this causes any real problem, but for consistency
and to remove some overhead we should still fix this by clearing /
handling only the enabled interrupt events. Also this is a dependency
for the upcoming VLV power domain patchset where we need to disable all
the pipestat interrupts whenever the display power well is off.
v2:
- inline the status->enable mask mapping (Ville)
- don't check for invalid PSR bit on platforms other than VLV (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Frob conflict due to different merge order.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least on VLV we can't get at the pipestat status bits by simply right
shifting the corresponding enable bits. The mapping between enable and
status bits for the sprite0,1 flip done and the PSR events don't follow
this rule, so we need to map them separately.
The PSR enable for pipe A is DPFLIPSTAT[22], but I haven't added support
for this, since there is no user of it atm. Until support is added WARN
if someone tries to enable PSR interrupts, or tries to enable the same
(1 << 6) bit on pipe B, which MBZ.
v2:
- inline the status->enable mask mapping (Ville)
- fix bogus use of status bits in enable mask (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There isn't any PSR interrupt enable bit for pipe A, so we couldn't
enable it through the current API. Passing the corresponding status bits
solves this and also makes the mapping between enable and status bits
simpler on VLV (addressed in an upcoming patch).
Except of checking for invalid status bit arguments, no functional
change.
v2: split out the low level parts of i915_enable_pipestat accepting
separate enabled and status masks, to make the non-standard mapping
between those masks stand out more (added in the next patch)
(Jesse,Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We had 2 set of defines for the same register, so make it one.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turns out it'd be nice to change some device information at run-time or simply
have some code to fill in the info struct instead of having to declare the
values in 30+ structures.
What prompted this change is handling fused out display/pipe and tweaking
num_pipes at run-time, but I'm quite sure we'll find other flags/limits to
stick into dev_priv->info.
Most of the changes were done with a sed:
sed -i -e 's/dev_priv->info->/dev_priv->info./g' drivers/gpu/drm/i915/*[ch]
with a few tweaks to make it all work:
- Change the field definition in struct drm_i915_private
- adjust i915_dump_device_info()
- adjust i915_driver_load()
- adjust the INTEL_INFO() macro
v2: cast the info pointer returned by INTEL_INFO() to be const to catch
uses that would modify the structure post-initialization.
(Ville Syrjälä)
v3: Redo the patch onto latest drm-nightly,
Keep the info field const to catch post initialization writes
instead of the v2 solution,
Use a direct structure copy for the initial info initialization to
use the compiler type safety (Ville Syrjälä)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> (for v2)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (for v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to Bspec we need to disable SF pipelined attribute fetch
whenever SF outputs exceed 16 and normal clip mode is used. A quick
glance at Mesa suggests that these conditions could happen. So let's
just always set the magic bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
s/FLIPDONE/FLIP_DONE/ to make all FLIP_DONE macro names consistent.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
RFCv2: Reorganize array indexing so that full offsets can be used as
is. It makes grepping for registers in i915_reg.h much easier. Also
move offset arrays to intel_device_info.
v1: Fixed offsets for VLV, proper eDP handling
v2: Fixed BCLRPAT, PIPESRC, PIPECONF and DSP* macros.
v3: Added EDP pipe comment, removed redundant offset arrays for
MSA_MISC and DDI_FUNC_CTL.
v4: Rename patch and report object size increase.
v5: Change location of commas, add PIPE_EDP into enum pipe
v6: Insert PIPE_EDP_OFFSET into pipe offset array
v7: Set I915_MAX_PIPES back to 3, change more registers accessors
to use the new macros, get rid of _PIPE_INC and add dev_priv
as a parameter where required by the new macros.
Upcoming hardware will not have the various display pipe register
ranges evenly spaced in memory. Change register address calculations
into array lookups.
Tested on SNB, VLV, IVB, Gen2 and HSW w/eDP.
I left the UMS cruft untouched.
Size differences:
text data bss dec hex filename
596431 4634 56 601121 92c21 i915.ko (new)
593199 4634 56 597889 91f81 i915.ko (old)
Signed-off-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we enter RC6 and GFX Clocks are off, the voltage remains higher
than Vmin. When we try to set the freq to RPn, it might fail since the
Gfx clocks are down. So to fix this in Gfx idle, Bring the GFX clock up
and set the freq to RPn then move GFx down.
v2: remove vlv_update_rps_cur_delay function. Update commit message (Daniel)
v3: Fix the timeout during wait for gfx clock (Jesse)
v4: addressed comments on set freq and punit wait (Ville)
v5: use wait_for while waiting for GFX clk to be up. (Daniel)
update cur_delay before requesting min_delay. (Ville)
v6: use wait_for while waiting for punit. (Ville)
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The optimization is available on Ivy Bridge and later, and is disabled by
default. Enabling it helps certain workloads such as GLBenchmark TRex test.
No piglit regression.
v2
- no need to save the register before suspend as init_clock_gating can
correctly program it after resume
- split IVB change to another commit
Signed-off-by: Chia-I Wu <olv@lunarg.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least I couldn't find it in the Haswell Bspec any more and we've
tried to test-boot a Haswell machine with num_pipes forced to 0 (i.e.
hit the PCH_NOP path) and the unclaimed register logic complained.
So restrict this dance to just ivb platforms.
v2: Art pointed out that the bits simply moved on hsw+
v3: Buy code terseneness with a notch of sublety as suggested by
Chris.
v4: Frob the right bit, spotted by Art.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Arthur Ranyan <arthur.j.runyan@intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Having a 4 byte register at 0x321b seems unlikely as that's not
4 byte aligned. Since later platforms have more or less the same FBC
registers with new names, assume that FBC_FENCE_OFF is at 0x3218 just
like DPFC_FENCE_YOFF.
This feels like a simple typo in BSpec. 321Bh looks a lot like 3218h
after all.
Should still be tested on real hardware of course. But I don't have
any mobile gen4 systems.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make the FBC plane macros take the plane as a parameter.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read out and calculate the port and pixel clocks on DDI configs as well.
This means we have to grab the DP divider values and look at the port
mapping to figure out which clock select reg to read out.
v2: do the work from ddi_get_config (Ville)
v3: check WRPLL reference clock (Ville)
add additional SPLL freqs (Ville)
clean up port/crtc clock calc (Ville)
fix up crtc_clock conditionals (Ville)
drop superfluous dp_get_m_n from get_config (Ville)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was forgotten in
commit 565ee3897f
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Nov 13 12:56:29 2013 +0200
drm/i915: do not save/restore backlight registers in KMS
Since the confusion was likely due to the duplicated definition for
this pci config register, let's unify that, too.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 446f254566.
I've left the masking in the pageflip code since that seems to be some
useful piece of preemptive robustness.
Iirc I've merged this patch under the assumption that the BIOS leaves
some random gunk in the lower bits and gets unhappy if we trample on
them. We have quite a few case like this, so this made sense.
Now I've just learned that there's actual hardware features bits in
the low 12 bits, and the kernel needs to preserve them to allow a
userspace blob to do its job. Given Dave Airlie's clear stance on
userspace blob drivers I've quickly chatted with him and he doesn't
seem too happy. So let's revert this.
If there are indeed bits that we must preserve in this range then we
can ressurrect this patch, but with proper documentation for those
bits supplied. And we probably also need to think a bit about
interactions with our driver.
Cc: Armin Reese <armin.c.reese@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dave Airlie <airlied@linux.ie>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add new definitions for hotplug live status bits for VLV2 since they're
in reverse order from the gen4x ones.
Changelog:
- Restored gen4 bit definitions
- Added new definitions for VLV2
- Added platform check for IS_VALLEYVIEW() in dp_detect to use the correct
bit defintions
- Replaced a lost trailing brace for the added switch()
Signed-off-by: Todd Previte <tprevite@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73951
[danvet: Switch to _VLV postfix instead of prefix and regroupg
comments again so that the g4x warning is right next to those defines.
Also add a _G4X suffix for those special ones. Also cc stable.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix typo possibly leading to timed out DP aux transactions on ports C,D.
Introduced in:
Commmit 4aeebd7443
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 31 09:53:36 2013 +0100
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=72210
Signed off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Many of the fields from Gen6 have gone away for vlv. Strip all those
fields that are not relevent and try to update fields that we care
about. This patch give information about current RP & RC status and
individual Wells.
v2: Move Render & Media Well status to separate lines (Ville)
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On IVB the display data buffer partitioning control lives in the
DISP_ARB_CTL2 register. Add the relevant defines/code for it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few command were out of numerical order and had different spacing. Put
them back in numerical order, with proper spacing.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaVSRefCountFullforceMissDisable and
WaDSRefCountFullforceMissDisable
VS is a carry-over from HSW, and DS is likely not used by anyone yet.
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Line of 106 chars is too long. Really.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I stumbled on to some unimplemented errata. To be honest, I am not
really sure of the impact, just that the docs say to do.
No w/a name for this one.
v2: v1 was a stale thing which should have never seen the light of day.
(Haihao)
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Every ring seems to have a BB_ADDR registers, so include them all in the
error state.
v2: Also include the _UDW on BDW
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilons <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Setting this bit restores all ring contexts in parallel rather than
serially. Matches current BWG recommendations.
Tested-by: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Deepak S <deepak.s@inel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV the GTFIFOCTL register has other bits besides the number of free
entries in the GT wake FIFO. Apply a mask when we read th register to
make sure we don't misinterpret the number of free FIFO entries.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: There's some unclarity about hsw, but brushed off as todays'
Bspec just acting up a bit.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV GTFIFODBG has more bits. Just report them all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We send the primary and cursor plane data through the gamma unit.
In order to get matching output from sprites, also send the sprite
data through the gamma unit.
In the future we should add some properties to control this
explicitly, and also add properties for the per-sprite gamma ramps
what have you, but for now this seems like a reasonable thing to do.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec tells us that we need to emit an SRM after the LRI
to MSG_FBC_REND_STATE.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now we have this everywhere. Next up would be to wire up the DP
hotplug pin to speed up panel power sequencing for eDP panels ...
I've decided to leave the has_aux_irq logic in the code, it should
come handy for hw bringup.
For testing/fail-safety the dp aux code already has a timeout when
waiting for interrupts to signal completion and screams rather loud if
they don't arrive in time. Given that we need a real piece of hw to
talk to anyway this is probably as good as it gets.
v2: Don't check the dp aux channel bits on i965 machines, they have a
different meaning there. Yay for reusing bits at will! Spotted by
Jani.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in Jani's backlight rework branch. This was merged through a
separate branch to be able to sort out the Broadwell conflicts
properly before pulling it into the main development branch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vlv_dpio_read/write should be describe more in PHY centric instead of
display controller centric.
Create a enum dpio_channel for channel index and enum dpio_phy for PHY
index. This should better to gather for upcoming platform.
v2: Rebase the code based on
drm/i915/vlv: Fix typo in the DPIO register define.
v3: Rename vlv_phy to dpio_phy_iosf_port and define additional macro
DPIO_PHY, and remove unrelated change. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So here's the Broadwell pull request. From a kernel driver pov there's
two areas with big changes in Broadwell:
- Completely new enumerated interrupt bits. On the plus side it now looks
fairly unform and sane.
- Completely new pagetable layout.
To ensure minimal impact on existing platforms we've refactored both the
irq and low-level gtt handling code a lot in anticipation of the bdw push.
So now bdw enabling in these areas just plugs in a bunch of vfuncs.
Otherwise it's all fairly harmless adjusting of switch cases and
if-ladders to shovel bdw into the right blocks. So minimized impact on
existing platforms. I've also merged the bdw-stage1 branch into our
-nightly integration branch for the past week to make sure we don't break
anything.
Note that there's still quite a flurry or patches floating around, but
I've figured I'll push this out. I plan to keep the bdw fixes separate
from my usual -fixes stream so that you can reject them easily in case it
still looks like too much churn. Also, bdw is for now hidden behind the
preliminary hw enabling module option. So there's no real pressure to get
follow-up patches all into 3.13.
* tag 'bdw-stage1-2013-11-08-v2' of git://people.freedesktop.org/~danvet/drm-intel: (75 commits)
drm/i915: Mask the vblank interrupt on bdw by default
drm/i915: Wire up cpu fifo underrun reporting support for bdw
drm/i915: Optimize gen8_enable|disable_vblank functions
drm/i915: Wire up pipe CRC support for bdw
drm/i915: Wire up PCH interrupts for bdw
drm/i915: Wire up port A aux channel
drm/i915: Fix up the bdw pipe interrupt enable lists
drm/i915: Optimize pipe irq handling on bdw
drm/i915/bdw: Take render error interrupt out of the mask
drm/i915/bdw: Add BDW PCH check first
drm/i915: Use hsw_crt_get_config on BDW
drm/i915/bdw: Change dp aux timeout to 600us on DDIA
drm/i915/bdw: Enable trickle feed on Broadwell
drm/i915/bdw: WaSingleSubspanDispatchOnAALinesAndPoints
drm/i915/bdw: conservative SBE VUE cache mode
drm/i915/bdw: Limit SDE poly depth FIFO to 2
drm/i915/bdw: Sampler power bypass disable
ddrm/i915/bdw: Disable centroid pixel perf optimization
drm/i915/bdw: BWGTLB clock gate disable
drm/i915/bdw: Implement edp PSR workarounds
...
HW engineers have listened and given us again a real interrupt with
masking and status regs. Yay!
For consistency with other platforms call the #define FIFO_UNDERRUN.
Eventually we also might need to have some enable/disable functions
for bdw display interrupts, but for now open-coding seems to be good
enough.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Useful for dp aux to work better. Also stop enabling the port A
hotplug event - eDP panels are expected to fire that interupt and
we're not really ready to deal with them. This is consistent with how
we handle port A on ilk-hsw.
The more important bit is that we must delay the enabling of hotplug
interrupts until all the encoders are fully set up. But we need irq
support earlier than that, hence hotplug interrupts can only be
enabled in the ->hpd_irq_setup callback.
v2: Drop the _HOTPLUG, it isn't (Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Pipe underrun can't just be enabled, we need some support code like
on ilk-hsw to make this happen. So drop it for now.
- CRC error is a special mode of the CRC hardware that we don't use,
so again drop it. Real CRC support for bdw will be added later.
- All the other error bits are about faults, so rename the #define and
adjust the output.
v2: Use pipe_name as pointed out by Ville. Ville's comment was on a
previous patch, but it was easier to squash in here.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a per-pipe bit in the master irq control register, so use it.
This allows us to drop the masks for aggregate interrupt bits and be a
bit more explicit in the code. It also removes one indentation level.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Hold vertex data in cache until last reference
BDW-A workaround
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW-A workaround
BDW Bug #1899532
v2: WARN on when not using preliminary HW support
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuosugeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This implements a workaround for PSR dealing with some vblank issue.
WaPsrDPAMaskVBlankInSRD && WaPsrDPRSUnmaskVBlankInSRD
v2: forgot to git add bogus whitespace fix
v3: Update with workaround names.
Use for_each_pipe() and CHICKEN_PIPESL_1(pipe) macro (Ville)
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuosugeek.org>
[danvet: Kill redundant IS_BDW check and remove the copious amount of
uneeded lines added.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broadwell PSR support is a superset of Haswell. With this simple
register base calculation, everything that worked on HSW for eDP PSR
should work on BDW.
Note that Broadwell provides additional PSR support. This is not
addressed at this time.
v2: Make the HAS_PSR include BDW
v3: Use the correct offset (I had incorrectly used one from my faulty
brain) (Art!)
v4: It helps if you git add
v5: Be explicit about not setting min link entry time for BDW. This
should be no functional change over v4 (Jani)
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Squash in fixup from Ben to synchronize the GT mailbox commands.
CC: Art Runyan <arthur.j.runyan@intel.com>
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broadwell has bigger display FIFOs than Haswell. Otherwise the
two are very similar.
v2: Fix FBC WM_LP shift for BDW
v3: Rebase on top of the big Haswell wm rework.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They're not the same as the Haswell ones.
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebased onto Paulo's MHz->kHz change.
v3: Rebased on top of the Haswell pc8+ adjustements.
v4: Use the exact 337.5MHz clock, should have been done as part of v2.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And it inherits some bits from the previous TRANS_CONF (aka PIPE_CONF
on previous gens).
v2: Rebase on to of the pipe config bpp handling rework.
v3: Rebased on top of the pipe_config->dither refactoring.
v4: Drop the read-modify-write cycle for PIPEMISC, similarly to how we
now also build up PIPECONF completely ourselves - keeping around
random stuff set by the BIOS just isn't a good idea. I've checked BDW
BSpec and we already set all relevant bits.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Legacy PPGTT on GEN8 requires programming 4 PDP registers per ring.
Since all rings are using the same address space with the current code
the logic is simply to program all the tables we've setup for the PPGTT.
v2: Turn on PPGTT in GFX_MODE
v3: v2 was the wrong patch
v4: Resolve conflicts due to patch series reordering.
v5: Squash in fixup from Ben: Use LRI to write PDPs
The docs (and simulator seems to back up) suggest that we can only
program legacy PPGTT PDPs with LRI commands.
v6: Rebase around context differences conflicts.
v7: Use #defines for per ring PDPs. (Damien)
v8: Don't use typede'f private_t.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (up to v3 and v7)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW caching works differently than the previous generations. Instead of
having bits in the PTE which directly control how the page is cached,
the 3 PTE bits PWT PCD and PAT provide an index into a PAT defined by
register 0x40e0. This style of caching is functionally equivalent to how
it works on HSW and before.
v2: Tiny bikeshed as discussed on internal irc.
v3: Squash in patch from Ville to mirror the x86 PAT setup more like
in arch/x86/mm/pat.c. Primarily, the 0th index will be WB, and not
uncached.
v4: Comment for reason to not use a 64b write on the PPAT.
v5: Add a FIXME comment that the caching bits in the PAT registers
might be wrong due to doc confusion.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The command to emit batch buffers has changed to address 48b addresses.
It seemed reasonable that we could still use the old instruction where
emitting 0 for length would do the right thing, but it seems to bother
the simulator when the code does that.
Now the second dword in the command has the upper 16b of the address of
the batchbuffer.
v2: Remove duplicated vfun assignment.
v3: Squash in VECS support changes from Zhao Yakui <yakui.zhao@intel.com>
v4: Make checkpatch happy.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The interrupt handling implementation remains the same as previous
generations with the 4 types of registers, status, identity, mask, and
enable. However the layout of where the bits go have changed entirely.
To address these changes, all of the interrupt vfuncs needed special
gen8 code.
The way it works is there is a top level status register now which
informs the interrupt service routine which unit caused the interrupt,
and therefore which interrupt registers to read to process the
interrupt. For display the division is quite logical, a set of interrupt
registers for each pipe, and in addition to those, a set each for "misc"
and port.
For GT the things get a bit hairy, as seen by the code. Each of the GT
units has it's own bits defined. They all look *very similar* and
resides in 16 bits of a GT register. As an example, RCS and BCS share
register 0. To compact the code a bit, at a slight expense to
complexity, this is exactly how the code works as well. 2 structures are
added to the ring buffer so that our ring buffer interrupt handling code
knows which ring shares the interrupt registers, and a shift value (ie.
the top or bottom 16 bits of the register).
The above allows us to kept the interrupt register caching scheme, the
per interrupt enables, and the code to mask and unmask interrupts
relatively clean (again at the cost of some more complexity).
Most of the GT units mentioned above are command streamers, and so the
symmetry should work quite well for even the yet to be implemented rings
which Broadwell adds.
v2: Fixes up a couple of bugs, and is more verbose about errors in the
Broadwell interrupt handler.
v3: fix DE_MISC IER offset
v4: Simplify interrupts:
I totally misread the docs the first time I implemented interrupts, and
so this should greatly simplify the mess. Unlike GEN6, we never touch
the regular mask registers in irq_get/put.
v5: Rebased on to of recent pch hotplug setup changes.
v6: Fixup on top of moving num_pipes to intel_info.
v7: Rebased on top of Egbert Eich's hpd irq handling rework. Also
wired up ibx_hpd_irq_setup for gen8.
v8: Rebase on top of Jani's asle handling rework.
v9: Rebase on top of Ben's VECS enabling for Haswell, where he
unfortunately went OCD on the gt irq #defines. Not that they're still
not yet fully consistent:
- Used the GT_RENDER_ #defines + bdw shifts.
- Dropped the shift from the L3_PARITY stuff, seemed clearer.
- s/irq_refcount/irq_refcount.gt/
v10: Squash in VECS enabling patches and the gen8_gt_irq_handler
refactoring from Zhao Yakui <yakui.zhao@intel.com>
v11: Rebase on top of the interrupt cleanups in upstream.
v12: Rebase on top of Ben's DPF changes in upstream.
v13: Drop bdw from the HAS_L3_DPF feature flag for now, it's unclear what
exactly needs to be done. Requested by Ben.
v14: Fix the patch.
- Drop the mask of reserved bits and assorted logic, it doesn't match
the spec.
- Do the posting read inconditionally instead of commenting it out.
- Add a GEN8_MASTER_IRQ_CONTROL definition and use it.
- Fix up the GEN8_PIPE interrupt defines and give the GEN8_ prefixes -
we actually will need to use them.
- Enclose macros in do {} while (0) (checkpatch).
- Clear DE_MISC interrupt bits only after having processed them.
- Fix whitespace fail (checkpatch).
- Fix overtly long lines where appropriate (checkpatch).
- Don't use typedef'ed private_t (maintainer-scripts).
- Align the function parameter list correctly.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v4)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
bikeshed
Just enough to make the code not barf...
Init BDW display to look like HSW. For the simulator this should be
fine, but this will probably require more work.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Add a FIXME comment about RCS flips being untested on bdw.
Also add a note that hblank events are reserved on bdw+ in DERRMR.]
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW context sizes varies a bit.
v2: Squash in fixup for the hw context size from Ben.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some VLV PHY/PLL DPIO registers have group/lane/channel access. Current
DPIO register definition doesn't have a structure way to break them
down. As a result it is not easy to match the PHY/PLL registers with the
configdb document. Rename those registers based on the configdb for easy
cross references, and without the need to check the offset in the header
file.
New format is as following.
<platform name>_<DPIO component><optional lane #>_DW<dword # in the
doc>_<optional channel #>
For example,
VLV_PCS_DW0 - Group access to PCS for lane 0 to 3 for PCS DWORD 0.
VLV_PCS01_DW0_CH0 - PCS access to lane 0/1, channel 0 for PCS DWORD 0.
Another example is
VLV_TX_DW0 - Group access to TX lane 0 to 3 for TX DWORD 0
VLV_TX0_DW0 - Refer to TX Lane 0 access only for TX DWORD 0.
There is no functional change on this patch.
v2: Rebase based on previous patch change.
v3: There may be configdb different version that document the start DW
differently. Add a comment to clarify. Fix up some mismatch start DW
for second PLL block. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the connector and pipe passed around, we can now set the backlight
on the right pipe on VLV/BYT.
v2: drop combination mode check for VLV (Jani)
add save/restore code for VLV backlight regs (Jani)
check for existing modulation freq when initializing backlight regs (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67245
Tested-by: Joe Konno <joe.konno@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/BYT, we can adjust the CDclk frequency up or down based on the
max pixel clock we need to drive. Lowering it can save power, while
raising it is necessary to support high resolution.
Add a new callback in modeset_affected_pipes and a
modeset_global_resources function to perform this adjustment as
necessary.
v2: use punit interface for 320 and 266 MHz CDclk adjustments (Ville)
v3: reset GMBUS dividers too, since we changed CDclk (Ville)
v4: jump to highest voltage when going to 400MHz CDclk (Jesse)
v5: drop duplicate define (Ville)
use shifts by 1 for fixed point (Ville)
drop new callback (Daniel)
v6: fixup adjusted_mode.clock -> adjusted_mode.crtc_clock again (Ville)
document Bunit reg access better (Ville)
v7: pass modeset_pipes and pipe_config to global_pipes so we get the right
clock data (Ville)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch defines HD-Audio configuration registers and enables display audio
from HDA controller for Valleyview2.
v2: fix missing offset VLV_DISPLAY_BASE
v3: rename patch from 'enable HDMI audio' to 'enable HDA display audio', since
it's for both HDMI and DP audio
v4: use enc_to_dig_port() to get port number, instead of using Haswell specific
function intel_ddi_get_encoder_port()
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I want to merge in the new Broadwell support as a late hw enabling
pull request. But since the internal branch was based upon our
drm-intel-nightly integration branch I need to resolve all the
oustanding conflicts in drm/i915 with a backmerge to make the 60+
patches apply properly.
We'll propably have some fun because Linus will come up with a
slightly different merge solution.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_crt.c
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_drv.h
All rather simple adjacent lines changed or partial backports from
-next to -fixes, with the exception of the thaw code in i915_dma.c.
That one needed a bit of shuffling to restore the intent.
Oh and the massive header file reordering in intel_drv.h is a bit
trouble. But not much.
v2: Also don't forget the fixup for the silent conflict that results
in compile fail ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to reset the DP scrambler on every vsync to get stable CRCs.
And since we can't use the normal pipe CRC on DP ports on g4x we
really need them to be able to test modesetting issues on (e)DP
outputs.
Note that the DC balance reset is for SDVO port CRCs so we don't
strictly need it. But better safe than sorry (and it's a nice template
in case we ever want to grab port CRCs for e.g. audio checking).
v2: Apply the suggestions from Damien's review.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Incorrect definition DPIO_TX3_SWING_CTL4.
From Ville's review: "Based on the specs, the typo meant that HDMI B
ended up using "incorrect" de-emphasis for the TMDS data lanes."
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add comment from Ville's review about the impact.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Use a for_each_loop and add the corresponding #defines.
- Drop the _ILK postfix on the existing DE_PIPE_VBLANK macro for
consistency with everything else.
- Also use macros (and add the missing one for plane flips) for the
ivb display interrupt handler.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Drop the useless parens that Ville spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bbstate contains useful bits of debugging information such as
whether the batch is being read from GTT or PPGTT, or whether it is
allowed to execute privileged instructions.
v2: Only record BB_STATE for gen4+
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Production HSW does not need it. I confirmed this with Art.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All our registers which are written through the MCHBAR are defined
descriptively as an offset to the MCHBAR. We had 3 outliers here.
Convert these as well so all registers which are offsets are MCHBAR can
be easily identified/found within the code.
With this, convert DCLK to also follow this format.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Really simple, and we don't even have working frame numbers.
v2: Actually enable it ...
v3: Review from Ville:
- Unconditionally enable the border in the CRC checksum for
consistency with gen3+.
- Handle the "none" source to be able to disable the CRC machinery
again.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The PIPE_B #define was missing the display mmio offset. Use the
_PIPE_INC macro instead, it's simpler.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A bit a mess, since with DP/TV outputs we can't use the pipe CRC.
Also, no plane CRCs, so we need to update the basic testcases.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Should work down to gen2. The #defines for the interrupt sources are
already there in PIPESTAT and are the same on all gmch platforms for
gen2 up to vlv.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Once the machine gets to a certain point in the suspend process, we
expect the GPU to be idle. If it is not, we might corrupt memory.
Empirically (with an early version of this patch) we have seen this is
not the case. We cannot currently explain why the latent GPU writes
occur.
In the technical sense, this patch is a workaround in that we have an
issue we can't explain, and the patch indirectly solves the issue.
However, it's really better than a workaround because we understand why
it works, and it really should be a safe thing to do in all cases.
The noticeable effect other than the debug messages would be an increase
in the suspend time. I have not measure how expensive it actually is.
I think it would be good to spend further time to root cause why we're
seeing these latent writes, but it shouldn't preclude preventing the
fallout.
NOTE: It should be safe (and makes some sense IMO) to also keep the
VALID bit unset on resume when we clear_range(). I've opted not to do
this as properly clearing those bits at some later point would be extra
work.
v2: Fix bugzilla link
Bugzilla: http://bugs.freedesktop.org/show_bug.cgi?id=65496
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59321
Tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Tested-By: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
hw designers decided to change the CRC registers and coalesce them all
into one. Otherwise nothing changed. I've opted for a new hsw_ version
to grab the crc sample since hsw+1 will have the same crc registers,
but different interrupt source registers. So this little helper
function will come handy there.
Also refactor the display error handler with a neat pipe loop.
v2: Use for_each_pipe.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We enable the interrupt unconditionally and only control it
through the enable bit in the CRC control register.
v2: Extract per-platform helpers to compute the register values.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also add a new _PIPE_INC macro which takes an base plus increment.
Much less likely to botch the job by missing an s/A/B/ somewhere.
v2: They've moved the bitfield. Argh!
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The HDMI audio expects HDMI pixel clock to be set in the audio
configuration. We've currently just set 0, using 25.2 / 1.001 kHz
frequency, which fails with some modes.
v2: Now with a commit message.
Reference: http://mid.gmane.org/CAGpEb3Ep1LRZETPxHGRfBDqr5Ts2tAc8gCukWwugUf1U5NYv1g@mail.gmail.com
Reference: http://mid.gmane.org/20130206213533.GA16367@hardeman.nu
Reported-by: David Härdeman <david@hardeman.nu>
Reported-by: Jasper Smet <josbeir@gmail.com>
Tested-by: Jasper Smet <josbeir@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä