Update email address on mach-bcm + drivers for Broadcom mobile SoCs.
Signed-off-by: Christian Daudt <csd@broadcom.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The use of extern in .h files is a bit contentious.
Make the warning be emitted only when --strict is used on the command
line.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The arg64 struct has a hole after ->buf_size which isn't cleared. Or if
any of the calls to copy_from_user() fail then that would cause an
information leak as well.
This was assigned CVE-2013-2147.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pciinfo struct has a two byte hole after ->dev_fn so stack
information could be leaked to the user.
This was assigned CVE-2013-2147.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 1b3a5d02ee ("reboot: move arch/x86 reboot= handling to generic
kernel") did some cleanup for reboot= command line, but it made the
reboot_default inoperative.
The default value of variable reboot_default should be 1, and if command
line reboot= is not set, system will use the default reboot mode.
[akpm@linux-foundation.org: fix comment layout]
Signed-off-by: Li Fei <fei.li@intel.com>
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Acked-by: Robin Holt <robinmholt@linux.com>
Cc: <stable@vger.kernel.org> [3.11.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit 829199197a ("kernel/audit.c: avoid negative sleep
durations") audit emitters will block forever if userspace daemon cannot
handle backlog.
After the timeout the waiting loop turns into busy loop and runs until
daemon dies or returns back to work. This is a minimal patch for that
bug.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Richard Guy Briggs <rgb@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Chuck Anderson <chuck.anderson@oracle.com>
Cc: Dan Duval <dan.duval@oracle.com>
Cc: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit 3b38722efd ("memcg, vmscan: integrate soft reclaim
tighter with zone shrinking code")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit e883110aad ("memcg: get rid of soft-limit tree
infrastructure")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit a5b7c87f92 ("vmscan, memcg: do softlimit reclaim also
for targeted reclaim")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit de57780dc6 ("memcg: enhance memcg iterator to support
predicates")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit 7d910c054b ("memcg: track children in soft limit excess
to improve soft limit")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit e839b6a1c8 ("memcg, vmscan: do not attempt soft limit
reclaim if it would not scan anything")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit 1be171d60b ("memcg: track all children over limit in the
root")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit e975de998b ("memcg, vmscan: do not fall into reclaim-all
pass too quickly")
I merged this prematurely - Michal and Johannes still disagree about the
overall design direction and the future remains unclear.
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While printing 32-bit node numbers, an 8-byte string is not enough.
Increase the size of the string to 12 chars.
This got left out in commit 49fa8140e4 ("fs/ocfs2/super.c: Use bigger
nodestr to accomodate 32-bit node numbers").
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
watchdog_tresh controls how often nmi perf event counter checks per-cpu
hrtimer_interrupts counter and blows up if the counter hasn't changed
since the last check. The counter is updated by per-cpu
watchdog_hrtimer hrtimer which is scheduled with 2/5 watchdog_thresh
period which guarantees that hrtimer is scheduled 2 times per the main
period. Both hrtimer and perf event are started together when the
watchdog is enabled.
So far so good. But...
But what happens when watchdog_thresh is updated from sysctl handler?
proc_dowatchdog will set a new sampling period and hrtimer callback
(watchdog_timer_fn) will use the new value in the next round. The
problem, however, is that nobody tells the perf event that the sampling
period has changed so it is ticking with the period configured when it
has been set up.
This might result in an ear ripping dissonance between perf and hrtimer
parts if the watchdog_thresh is increased. And even worse it might lead
to KABOOM if the watchdog is configured to panic on such a spurious
lockup.
This patch fixes the issue by updating both nmi perf even counter and
hrtimers if the threshold value has changed.
The nmi one is disabled and then reinitialized from scratch. This has
an unpleasant side effect that the allocation of the new event might
fail theoretically so the hard lockup detector would be disabled for
such cpus. On the other hand such a memory allocation failure is very
unlikely because the original event is deallocated right before.
It would be much nicer if we just changed perf event period but there
doesn't seem to be any API to do that right now. It is also unfortunate
that perf_event_alloc uses GFP_KERNEL allocation unconditionally so we
cannot use on_each_cpu() and do the same thing from the per-cpu context.
The update from the current CPU should be safe because
perf_event_disable removes the event atomically before it clears the
per-cpu watchdog_ev so it cannot change anything under running handler
feet.
The hrtimer is simply restarted (thanks to Don Zickus who has pointed
this out) if it is queued because we cannot rely it will fire&adopt to
the new sampling period before a new nmi event triggers (when the
treshold is decreased).
[akpm@linux-foundation.org: the UP version of __smp_call_function_single ended up in the wrong place]
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
proc_dowatchdog doesn't synchronize multiple callers which might lead to
confusion when two parallel callers might confuse watchdog_enable_all_cpus
resp watchdog_disable_all_cpus (eg watchdog gets enabled even if
watchdog_thresh was set to 0 already).
This patch adds a local mutex which synchronizes callers to the sysctl
handler.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge bcache fixes from Kent Overstreet:
"There's fixes for _three_ different data corruption bugs, all of which
were found by users hitting them in the wild.
The first one isn't bcache specific - in 3.11 bcache was switched to
the bio_copy_data in fs/bio.c, and that's when the bug in that code
was discovered, but it's also used by raid1 and pktcdvd. (That was my
code too, so the bug's doubly embarassing given that it was or
should've been just a cut and paste from bcache code. Dunno what
happened there).
Most of these (all the non data corruption bugs, actually) were ready
before the merge window and have been sitting in Jens' tree, but I
don't know what's been up with him lately..."
* emailed patches from Kent Overstreet <kmo@daterainc.com>:
bcache: Fix flushes in writeback mode
bcache: Fix for handling overlapping extents when reading in a btree node
bcache: Fix a shrinker deadlock
bcache: Fix a dumb CPU spinning bug in writeback
bcache: Fix a flush/fua performance bug
bcache: Fix a writeback performance regression
bcache: Correct printf()-style format length modifier
bcache: Fix for when no journal entries are found
bcache: Strip endline when writing the label through sysfs
bcache: Fix a dumb journal discard bug
block: Fix bio_copy_data()
In writeback mode, when we get a cache flush we need to make sure we
issue a flush to the backing device.
The code for sending down an extra flush was wrong - by cloning the bio
we were probably getting flags that didn't make sense for a bare flush,
and also the old code was firing for FUA bios, for which we don't need
to send a flush to the backing device.
This was causing data corruption somehow - the mechanism was never
determined, but this patch fixes it for the users that were seeing it.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
btree_sort_fixup() was overly clever, because it was trying to avoid
pulling a key off the btree iterator in more than one place.
This led to a really obscure bug where we'd break early from the loop in
btree_sort_fixup() if the current key overlapped with keys in more than
one older set, and the next key it overlapped with was zero size.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GFP_NOIO means we could be getting called recursively - mca_alloc() ->
mca_data_alloc() - definitely can't use mutex_lock(bucket_lock) then.
Whoops.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bch_journal_meta() was missing the flush to make the journal write
actually go down (instead of waiting up to journal_delay_ms)...
Whoops
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Background writeback works by scanning the btree for dirty data and
adding those keys into a fixed size buffer, then for each dirty key in
the keybuf writing it to the backing device.
When read_dirty() finishes and it's time to scan for more dirty data, we
need to wait for the outstanding writeback IO to finish - they still
take up slots in the keybuf (so that foreground writes can check for
them to avoid races) - without that wait, we'll continually rescan when
we'll be able to add at most a key or two to the keybuf, and that takes
locks that starves foreground IO. Doh.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix
drivers/md/bcache/btree.c: In function ‘bch_btree_node_read’:
drivers/md/bcache/btree.c:259: warning: format ‘%lu’ expects type ‘long unsigned int’, but argument 3 has type ‘size_t’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The journal replay code didn't handle this case, causing it to go into
an infinite loop...
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sysfs attributes with unusual characters have crappy failure modes
in Squeeze (udev 164); later versions of udev are unaffected.
This should make these characters more unusual.
Signed-off-by: Gabriel de Perthuis <g2p.code@gmail.com>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
That switch statement was obviously wrong, leading to some sort of weird
spinning on rare occasion with discards enabled...
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The memcpy() in bio_copy_data() was using the wrong offset vars, leading
to data corruption in weird unusual setups.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.9
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_balloon_scratch_page() disables preemption so we cannot call
alloc_page() in between get/put_balloon_scratch_page(). Shuffle bits
around in decrease_reservation() to avoid this.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
xen_init_spinlocks() currently calls static_key_slow_inc() before
jump_label_init() is invoked. When CONFIG_JUMP_LABEL is set (which usually is
the case) the effect of this static_key_slow_inc() is deferred until after
jump_label_init(). This is different from when CONFIG_JUMP_LABEL is not set, in
which case the key is set immediately. Thus, depending on the value of config
option, we may observe different behavior.
In addition, when we come to __jump_label_transform() from jump_label_init(),
the key (paravirt_ticketlocks_enabled) is already enabled. On processors where
ideal_nop is not the same as default_nop this will cause a BUG() since it is
expected that before a key is enabled the latter is replaced by the former
during initialization.
To address this problem we need to move
static_key_slow_inc(¶virt_ticketlocks_enabled) so that it is called
after jump_label_init(). We also need to make sure that this is done before
other cpus start to boot. early_initcall appears to be a good place to do so.
(Note that we cannot move whole xen_init_spinlocks() there since pv_lock_ops
need to be set before alternative_instructions() runs.)
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v2: Added extra comments in the code]
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Upon deeper review it was agreed to remove the driver-unique
'locality' sysfs attribute before it is present in a released
kernel.
The attribute was introduced in e2683957fb
during the 3.12 merge window, so this patch needs to go in before
3.12 is released.
The hope is to have a well defined locality API that all the other
locality aware drivers can use, perhaps in 3.13.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
All the default durations were being set to 10 minutes which is
way too long for the timeouts. Normal values for the longest
duration are around 5 mins, and short duration ar around .5s.
Further, these are just the default, tpm_get_timeouts will set
them to values from the TPM (or throw an error).
Just remove them.
Acked-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This regression has been introduced in
commit 9f11a9e4e5
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jun 13 00:54:58 2013 +0200
drm/i915: set up PIPECONF explicitly for i9xx/vlv platforms
Ville brough up the idea that this is just the pipe A quirk gone
wrong.
Note that after resume the bios might or might not have enabled pipe A
already. We have a bit of magic to make sure that on resume we set up
a decent mode for pipe A, but I fear if I just smash pipe A to always
on we'd enable it in a bogus state and hang the hw. Hence the
readback.
v2: Clarify the logic a bit as suggested by Chris. Also amend the
commit message to clarify why we don't unconditionally enable the
pipe.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66462
References: https://lkml.org/lkml/2013/8/26/238
Cc: Meelis Roos <mroos@ut.ee>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Use |= instead of = as suggested by Chris.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The native TV encoder has it's own flags to adjust sync modes and
enabled interlaced modes which are totally irrelevant for the adjusted
mode. This worked out nicely since the input modes used by both the
load detect code and reported in the ->get_modes callbacks all have no
flags set, and we also don't fill out any of them in the ->get_config
callback.
This changed with the additional sanitation done with
commit 2960bc9cce
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Jul 30 13:36:32 2013 +0300
drm/i915: make user mode sync polarity setting explicit
sinc now the "no flags at all" state wouldn't fit through core code
any more. So fix this up again by explicitly clearing the flags in the
->compute_config callback.
Aside: We have zero checking in place to make sure that the requested
mode is indeed the right input mode we want for the selected TV mode.
So we'll happily fall over if userspace tries to pull us. But that's
definitely work for a different patch series. So just add a FIXME
comment for now.
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no clear cut rules or specs for the retry interval, as there
are many factors that affect overall response time. Increase the
interval, and even more so on branch devices which may have limited i2c
bit rates.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=60263
Tested-by: Nicolas Suzor <nic@suzor.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After a fair number of xfstests runs, xfs/182 started to fail
regularly with a corrupted directory - a directory read verifier was
failing after recovery because it found a block with a XARM magic
number (remote attribute block) rather than a directory data block.
The first time I saw this repeated failure I did /something/ and the
problem went away, so I was never able to find the underlying
problem. Test xfs/182 failed again today, and I found the root
cause before I did /something else/ that made it go away.
Tracing indicated that the block in question was being correctly
logged, the log was being flushed by sync, but the buffer was not
being written back before the shutdown occurred. Tracing also
indicated that log recovery was also reading the block, but then
never writing it before log recovery invalidated the cache,
indicating that it was not modified by log recovery.
More detailed analysis of the corpse indicated that the filesystem
had a uuid of "a4131074-1872-4cac-9323-2229adbcb886" but the XARM
block had a uuid of "8f32f043-c3c9-e7f8-f947-4e7f989c05d3", which
indicated it was a block from an older filesystem. The reason that
log recovery didn't replay it was that the LSN in the XARM block was
larger than the LSN of the transaction being replayed, and so the
block was not overwritten by log recovery.
Hence, log recovery cant blindly trust the magic number and LSN in
the block - it must verify that it belongs to the filesystem being
recovered before using the LSN. i.e. if the UUIDs don't match, we
need to unconditionally recovery the change held in the log.
This patch was first tested on a block device that was repeatedly
causing xfs/182 to fail with the same failure on the same block with
the same directory read corruption signature (i.e. XARM block). It
did not fail, and hasn't failed since.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
It uses a kernel internal structure in it's definition rather than
the user visible structure that is passed to the ioctl.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
When we free an inode, we do so via RCU. As an RCU lookup can occur
at any time before we free an inode, and that lookup takes the inode
flags lock, we cannot safely assert that the flags lock is not held
just before marking it dead and running call_rcu() to free the
inode.
We check on allocation of a new inode structre that the lock is not
held, so we still have protection against locks being leaked and
hence not correctly initialised when allocated out of the slab.
Hence just remove the assert...
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Regression introduced by commit 46f9d2e ("xfs: aborted buf items can
be in the AIL") which fails to lock the AIL before removing the
item. Spinlock debugging throws a warning about this.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
5c5e854b changed perf_event__synthesize_mmap_events to generate MMAP2
events. Since perf-trace does not have a handler for it it dies with a
segfault when trying to process files:
perf trace -i /tmp/perf.data
Segmentation fault
Signed-off-by: David Ahern <dsahern@gmail.com>
Link: http://lkml.kernel.org/r/1379900700-5186-4-git-send-email-dsahern@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The commit '2814eb0 perf kmem: Remove die() calls' disabled 'perf kmem'
command for machines without numa support. It made the command fail if
'/sys/devices/system/node' dir wasn't found.
Skipping the numa based initialization in case the directory is not
found and continue execution.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1379003976-5839-5-git-send-email-jolsa@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fix a bug that was introduced in commit c4c11dd160 ("drm/i2c: tda998x:
add video and audio input configuration") when Sebastian cleaned up my
original patch. Without this being fixed, audio is muted when the
display is turned off, never to be re-enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Darren Etheridge <detheridge@ti.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, IPC mechanisms do security and auditing related checks under
RCU. However, since security modules can free the security structure,
for example, through selinux_[sem,msg_queue,shm]_free_security(), we can
race if the structure is freed before other tasks are done with it,
creating a use-after-free condition. Manfred illustrates this nicely,
for instance with shared mem and selinux:
-> do_shmat calls rcu_read_lock()
-> do_shmat calls shm_object_check().
Checks that the object is still valid - but doesn't acquire any locks.
Then it returns.
-> do_shmat calls security_shm_shmat (e.g. selinux_shm_shmat)
-> selinux_shm_shmat calls ipc_has_perm()
-> ipc_has_perm accesses ipc_perms->security
shm_close()
-> shm_close acquires rw_mutex & shm_lock
-> shm_close calls shm_destroy
-> shm_destroy calls security_shm_free (e.g. selinux_shm_free_security)
-> selinux_shm_free_security calls ipc_free_security(&shp->shm_perm)
-> ipc_free_security calls kfree(ipc_perms->security)
This patch delays the freeing of the security structures after all RCU
readers are done. Furthermore it aligns the security life cycle with
that of the rest of IPC - freeing them based on the reference counter.
For situations where we need not free security, the current behavior is
kept. Linus states:
"... the old behavior was suspect for another reason too: having the
security blob go away from under a user sounds like it could cause
various other problems anyway, so I think the old code was at least
_prone_ to bugs even if it didn't have catastrophic behavior."
I have tested this patch with IPC testcases from LTP on both my
quad-core laptop and on a 64 core NUMA server. In both cases selinux is
enabled, and tests pass for both voluntary and forced preemption models.
While the mentioned races are theoretical (at least no one as reported
them), I wanted to make sure that this new logic doesn't break anything
we weren't aware of.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Acked-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Missing ULL when calculating the amount of vram
leads to an overflow when the amount of vram is >= 4G.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When dpm was merged, I added a new asic struct for
rv6xx, but it never got properly updated when the
hdmi callbacks were added due to the two patch sets
being developed in parallel.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=69729
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
There are two locks involved in managing the journal lists. The general
reiserfs_write_lock and the journal->j_flush_mutex.
While flush_journal_list is sleeping to acquire the j_flush_mutex or to
submit a block for write, it will drop the write lock. This allows
another thread to acquire the write lock and ultimately call
flush_used_journal_lists to traverse the list of journal lists and
select one for flushing. It can select the journal_list that has just
had flush_journal_list called on it in the original thread and call it
again with the same journal_list.
The second thread then drops the write lock to acquire j_flush_mutex and
the first thread reacquires it and continues execution and eventually
clears and frees the journal list before dropping j_flush_mutex and
returning.
The second thread acquires j_flush_mutex and ends up operating on a
journal_list that has already been released. If the memory hasn't
been reused, we'll soon after hit a BUG_ON because the transaction id
has already been cleared. If it's been reused, we'll crash in other
fun ways.
Since flush_journal_list will synchronize on j_flush_mutex, we can fix
the race by taking a proper reference in flush_used_journal_lists
and checking to see if it's still valid after the mutex is taken. It's
safe to iterate the list of journal lists and pick a list with
just the write lock as long as a reference is taken on the journal list
before we drop the lock. We already have code to handle whether a
transaction has been flushed already so we can use that to handle the
race and get rid of the trans_id BUG_ON.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Commit a3172027 introduced test_transaction as a requirement for
flushing old lists -- but it can never return 1 unless the transaction
has already been flushed.
As a result, we have a routine that iterates the j_realblocks list but
doesn't actually do anything. Since it's been this way since 2006 and
the latency numbers were what Chris expected, let's just rip it out.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
A user has reported an oops in udf_statfs() that was caused by
numOfPartitions entry in LVID structure being corrupted. Fix the problem
by verifying whether numOfPartitions makes sense at least to the extent
that LVID fits into a single block as it should.
Reported-by: Juergen Weigert <jw@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Christian Daudt