The driver are trying to create an 'ath9k' directory in debugfs for each
device currently. If there are more than one device in the system, the
second try will always fail.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs ath9k/phy#/wiphy can be used to show the current list of
virtual wiphys and to add/remove virtual wiphys. Eventually, this
interface could be replaced with a cfg80211/nl80211 command that is
passed through mac80211.
For example:
# cat /debug/ath9k/phy0/wiphy
primary: phy0
# echo add > /debug/ath9k/phy0/wiphy
# cat /debug/ath9k/phy0/wiphy
primary: phy0
secondary: phy1
# echo del=phy1 > /debug/ath9k/phy0/wiphy
# cat /debug/ath9k/phy0/wiphy
primary: phy0
In addition, following commands can be used to test pausing and
unpausing of the virtual wiphys:
pause=phy1
unpause=phy1
select=phy1
(select pauses and unpauses wiphys automatically based on channel)
schedule=500
(set wiphy scheduling interval in msec; 0 = disable; default value: 500)
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a very simple scheduler that goes through the wiphys and
schedules one at a time every N milliseconds (current default value:
500 ms). This is enough for initial testing, but there are number of
areas where a more complex scheduler can improve operations greatly.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow mac80211-controlled channel changes on an active wiphy and
especially during a scan. We need this as long as the scan is
controlled by mac80211. Moving this control into the driver could
allow some optimizations on scanning while using multiple virtual
interfaces, but for now, try to work as well as possible with the
current scan mechanism.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like channel change may fail in some cases and end up leaving
the hardware in state where it cannot transmit any frames. Add a
workaround to recover from this state if we detect that wiphy
selection is failing due to wiphys not leaving PAUSING state.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 should not be requesting us to transmit frames on paused
wiphys since we stop the TX queues. Just in case, add debug code to
make sure we catch if this were to happen.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For now, allow channel changes immediately and just force the other
virtual wiphys to paused state. This is needed to allow
mac80211-controlled scan to control channel changes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Notify the AP that we may be sleeping longer to allow the AP power
save code to buffer larger number of frames for us when using virtual
wiphys.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of always going through initialization/deinitialization steps,
do this only for the first/last wiphy to not break the other wiphys.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_wiphy_select() can be used to select a virtual wiphy to be
activated. Other virtual wiphys will be paused and once that is done,
the operational channel is changed and the wiphys that are on the
selected channel will be unpaused.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow virtual wiphys to be paused/unpaused to allow off-channel
operations. Pause will stop all TX queues for the wiphy and move the
STA into power save mode if in managed mode. Unpause wakes up the TX
queues and notifies the AP that the STA woke up if in managed mode.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow RX filter to pass through all broadcast/multicast frames (i.e.,
no BSSID filtering) if virtual interfaces are used. Software filtering
will be used in this case to drop broadcast/multicast frames for
foreign BSSIDs.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new struct ath_softc::sec_wiphy array is used to store information
about virtual wiphys and select which wiphy is used in calls to
mac80211. Each virtual wiphy will be assigned a different MAC address
based on the virtual wiphy index.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the initial step in allowing ath9k to register multiple
virtual radios (wiphys). The goal of virtual radios is to allow the
same radio to be shared for multiple virtual interfaces that may
operate on different channels. The mac80211 virtual interface support
is designed only for single channel operation and as such, it is not
suitable for this type of use. Anyway, it can be used on top of the
virtual radio concept, if desired (e.g., use two virtual radios to
handle two channels and then add multiple mac80211 virtual interfaces
on top of each virtual radio).
The new struct ath_wiphy is now registered as the driver data
structure for wiphy. This structure has a pointer to the shared (among
virtual wiphys of the same physical radio) struct ath_softc data. The
primary wiphy maintains the allocated memory for ath_softc. Secondary
(virtual) wiphys will only allocate the new ath_wiphy structure.
Registration of secondary wiphys is added in a separate patch.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using a hardcoded BSSID mask (mask for own addresses),
iterate through all active interfaces and determine the minimal mask
that covers all local addresses.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace the internal sc_vaps array and index values by using vif
pointer from mac80211. Allow multiple VIPs to be registered. Though,
number of beaconing VIFs is still limited by ATH_BCBUF (currently
1). Multiple virtual STAs support is not yet complete, but at least
the data structures should now be able to handle this.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to use ath_keyset() wrapper for
ath9k_hw_set_keycache_entry() calls. In addition, improve the comments
describing the key setting operations.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current bitmask is invalid, because the tx dma size is a 3 bit wide
value.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't store the beacon timestamp internally, nor
do we do any TIM handling in ath9k.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TSF has to be reset only once, upon bringing
the interface up in AP mode. For any beacon reconfigure calls
after that, resetting the TSF results in incorrect beacon generation.
The only exception is a change in the beacon interval,
which is indicated to the driver by mac80211 through
IEEE80211_CONF_CHANGE_BEACON_INTERVAL, handle this properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the code easier to understand.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never use SC_OP_NO_RESET, it is not configurable at all.
Remove all code that deals with this flag and make beacon
stuck processing simple.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove useless comments, fix indentation.
Also, remove all occurrences of ASSERT(vif) which are not needed.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only use case for this right now is ANI calibration,
but more might come up in the future.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old code doesn't work correctly e.g. on newer chipsets like AR5418+AR2122 and AR5416+AR2133.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So that a new created IBSS network
doesn't break on the first scan.
It seems to Sujith and me that this
stupid code unnecessary, too.
So remove it...
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restore network sleep mode in isr if power save is enabled.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This callback can be used to handle dynamic 20/40,
and changes in the operating channel's HT parameters.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used anywhere in ath9k and is just making the code more
confusing.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are number of small details about the keycache operations that
are very easy to miss (and forget), so better include detailed
comments in ath9k_hw_set_keycache_entry() to avoid having to figure
out this every time when having to touch this area.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect Michael MIC key (RX, should have been TX) was set for the
group key in AP mode. This resulted in all broadcast frames triggering
Michael MIC errors and eventual TKIP countermeasures. The change here
sets the correct Michael MIC key based on whether the local end is the
authenticator (well, AP for now).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Tested-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nohwcrypt=1 module parameter can now be used to disable hardware
crypto in ath9k. While the hardware acceleration handles most cases,
it may be useful to be able to force mac80211 software implementation
to be used for some tests, e.g., with virtual interface combinations
that may not yet be supported in the key cache configuration. In
addition, this allows management frame protection to be tested with
older hardware revisions.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An error path in ath9k_add_interface() did not unlock the sc->mutex and
could leave the driver in quite unresponsive state.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
802.11g is in 2 ghz band, not 5 ghz.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we are roaming we allow to follow beacon hints.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All regulatory hints (core, driver, userspace and 11d) are now processed in
a workqueue.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The short calibration interval is different for AP
mode, fix this. Also, the timer should be rearmed in
the calibration routine during scanning.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pci_release_region() has to be called after the device
has been disabled. Also remove a stray __init attribute.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using wrong chainmasks would have an adverse impact on performance.
This patch fixes chainmask retrieval for non-PCIE cards.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OLC_FOR_AR9280_20_LATER is defined in multiple places,
move it to a common location.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reset automatically the TSF on re-enabling beaconing after scanning
in IBSS mode causes several problems. For example a new created IBSS
network can't age before an other node has joined, because scans are
done automatically in that case. And several other strange bugs more...
The TSF reset is done manually in the higher level mac80211 code in
the cases were it's needed, so we don't need to do it here.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Passing beacons received from other BSS to s/w in non-scanning
state is unnecessary in STA mode. This patch filters them out in
h/w.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some APs don't start BA negotiation with the client before it is done
with the key handshake in WPA/RSN. With those APs, key handshake times
out if EAPOL frames are sent after addba request. So defer the BA negotiation
until we are done with tx/rx of all EAPOL frames.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting up the CAB queue requires only the beacon interval,
remove the function ath_get_beaconconfig() which is redundant.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos