commit f04b3787bbce4567e28069a9ec97dcd804626ac7 introduced
a regression for the ofdmtable writing.
It incorrectly removed the writing of the high 16bits for
a 32bit table write and initialized the direction identifier
too late.
This patch does also some cleanups to make the code much more
readable and adds a few comments, so non rocket scientists are
also able to understand what this address caching is all about.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BCM94311MCG rev 02 chip has an 802.11 core with revision 13 and
has not been supported until now. The changes include the following:
(1) Add the 802.11 rev 13 device to the ssb_device_id table to load b43.
(2) Add PHY revision 9 to the supported list.
(3) Change the 2-bit routing code for address extensions to 0b10 rather
than the 0b01 used for the 32-bit case.
(4) Remove some magic numbers in the DMA setup.
The DMA implementation for this chip supports full 64-bit addressing with
one exception. Whenever the Descriptor Ring Buffer is in high memory, a
fatal DMA error occurs. This problem was not present in 2.6.24-rc2 due
to code to "Bias the placement of kernel pages at lower PFNs". When
commit 44048d70 reverted that code, the DMA error appeared. As a "fix",
use the GFP_DMA flag when allocating the buffer for 64-bit DMA. At present,
this problem is thought to arise from a hardware error.
This patch has been tested on my system and by Cédric Caumont
<icare40@hotmail.com>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restart the hardware on too many PHY TX errors. A thousand PHY TX errors
per 15 seconds means we won't be able to recover for sure.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes it can be useful to see the FCS, especially when
bad-FCS frames are shown. Pass the FCS to mac80211 and let
it worry about snipping it off when required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When monitor mode is enabled, this will make b43 read out the
full 64-bit MAC time from the chip for each received packet.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The b43 driver is modified to use the new SPROM structure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use uninitialized_var() to avoid the following bogus warning:
CC [M] drivers/net/wireless/b43/debugfs.o
drivers/net/wireless/b43/debugfs.c: In function ‘b43_debugfs_read’:
drivers/net/wireless/b43/debugfs.c:355: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix my copyright notices in b43 and b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrite and sync A PHY initialization with specs, thus allowing for further
work to be done on 802.11a support. Note that A PHY initialization involves
G PHYs as well.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a consistent naming scheme for the ops.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the limits provided by mac80211.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put all access to wl->current_dev under protection of the mutex.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These drivers pass full mactime information to the stack, make them
indicate this via the new RX_FLAG_TSFT to get mac80211 to show this
information in monitor mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix rfkill code which caused a use-after-free bug.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the parsing of the RX data header channel field.
The current code parses the header incorrectly and passes a wrong
channel number and frequency for each frame to mac80211.
The FIXMEs added by this patch don't matter for now as the code
where they live won't get executed anyway. They will be fixed later.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes Bug #9414
Since addition of the rfkill callback, the LED associated with the off
switch on the radio has not worked for several reasons:
(1) Essential data in the rfkill structure were missing.
(2) The rfkill structure was initialized after the LED initialization.
(3) There was a minor memory leak if the radio LED structure was inited.
Once the above problems were fixed, additional difficulties were noted:
(4) The radio LED was in the wrong state at startup.
(5) The radio switch had to be manipulated twice for each state change.
(6) A circular mutex locking situation existed.
(7) If rfkill-input is built as a module, it is not automatically loaded.
This patch fixes all of the above.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix some left-over URLs and ifdefs in b43 and b43legacy drivers.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCMCIA needs an additional step to request the IRQ.
No need to add code to release the IRQ here, as that's done
automatically in pcmcia_disable_device().
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix an IRQ race condition in b43. If we call b43_stop_wireless_core(), it
will set the status of the device to INITIALIZED and the IRQ handler won't
care any longer about IRQs, thus the kernel will disable the IRQ if it's
shared (unless we boot it with the 'irqpoll' option). So we must disable
IRQs before changing the device status.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rfkill subsystem doesn't like code like that
rfkill_allocate();
rfkill_register();
rfkill_unregister();
rfkill_register(); /* <- This will crash */
This sequence happens with
modprobe b43
ifconfig wlanX up
ifconfig wlanX down
ifconfig wlanX up
Fix this by always re-allocating the rfkill stuff before register.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl->mutex might already be locked on initialization.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rounding a relative timeout we need to use round_jiffies_relative().
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix an uninitialized variable in drivers/net/wireless/b43/main.c::b43_start().
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes all double includes of the same file. This
makes scripts/checkincludes.pl happy.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
b43 wireless needs <linux/io.h>
linux/drivers/net/wireless/b43/pio.h: In function 'b43_pio_write':
linux/drivers/net/wireless/b43/pio.h:89: error: implicit declaration of function 'mmiowb'
linux/drivers/net/wireless/b43/phy.c: In function 'b43_phy_write':
linux/drivers/net/wireless/b43/phy.c:301: error: implicit declaration of function 'mmiowb'
linuxdrivers/net/wireless/b43/sysfs.c: In function 'b43_attr_interfmode_store':
linuxdrivers/net/wireless/b43/sysfs.c:147: error: implicit declaration of function 'mmiowb'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This "algorithm" is used only internally and is not useful.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Buesch <mb@bu3sch.de>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement much easier and more lightweight locking for
the periodic work.
This also removes the last big busywait loop and replaces it
by a sleeping loop.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the direct call to rfkill on an rfkill event
and replaces it with an input device. This way userspace is also
notified about the event.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds full support for the RFKILL button and
the RFKILL LED trigger.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drive the LEDs through the generic LED triggers.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers are currently supposed to keep track of monitor
interfaces if they allow so-called "hard" monitor, and
they are also supposed to keep track of multicast etc.
This patch changes that, replaces the set_multicast_list()
callback with a new configure_filter() callback that takes
filter flags (FIF_*) instead of interface flags (IFF_*).
For a driver, this means it should open the filter as much
as necessary to get all frames requested by the filter flags.
Accordingly, the filter flags are named "positively", e.g.
FIF_ALLMULTI.
Multicast filtering is a bit special in that drivers that
have no multicast address filters need to allow multicast
frames through when either the FIF_ALLMULTI flag is set or
when the mc_count value is positive.
At the same time, drivers are no longer notified about
monitor interfaces at all, this means they now need to
implement the start() and stop() callbacks and the new
change_filter_flags() callback. Also, the start()/stop()
ordering changed, start() is now called *before* any
add_interface() as it really should be, and stop() after
any remove_interface().
The patch also changes the behaviour of setting the bssid
to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING
is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed
and the filter flag FIF_BCN_PRBRESP_PROMISC introduced.
This is a lot more efficient for hardware like b43 that
supports it and other hardware can still set the BSSID
to all-ones.
Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu
(rtl8187, adm8211, and p54), Larry Finger (b43legacy), and
Ivo van Doorn (rt2x00).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for turning the radio off in software.
That's useful in environments, where you don't want the RF
to radiate any signals, but don't want to bring the interface down.
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This message is useless. Only report state changes.
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also cleanup the code a bit and remove the inline.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not required and the txpower adjustment must not be in atomic.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Buesch