CH Pro Throttle needs NOGET the same way as other products from
the same vendor require.
Reported-by: Unavowed <unavowed@vexillium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There was an extra tab so the close curly brace didn't match up with
the right if statement.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (48 commits)
HID: add support for Logitech Driving Force Pro wheel
HID: hid-ortek: remove spurious reference
HID: add support for Ortek PKB-1700
HID: roccat-koneplus: vorrect mode of sysfs attr 'sensor'
HID: hid-ntrig: init settle and mode check
HID: merge hid-egalax into hid-multitouch
HID: hid-multitouch: Send events per slot if CONTACTCOUNT is missing
HID: ntrig remove if and drop an indent
HID: ACRUX - activate the device immediately after binding
HID: ntrig: apply NO_INIT_REPORTS quirk
HID: hid-magicmouse: Correct touch orientation direction
HID: ntrig don't dereference unclaimed hidinput
HID: Do not create input devices for feature reports
HID: bt hidp: send Output reports using SET_REPORT on the Control channel
HID: hid-sony.c: Fix sending Output reports to the Sixaxis
HID: add support for Keytouch IEC 60945
HID: Add HID Report Descriptor to sysfs
HID: add IRTOUCH infrared USB to hid_have_special_driver
HID: kernel oops in out_cleanup in function hidinput_connect
HID: Add teletext/color keys - gyration remote - EU version (GYAR3101CKDE)
...
Per the HID Specification, Feature reports must be sent and received on
the Configuration endpoint (EP 0) through the Set_Report/Get_Report
interfaces. This patch adds two ioctls to hidraw to set and get feature
reports to and from the device. Modifications were made to hidraw and
usbhid.
New hidraw ioctls:
HIDIOCSFEATURE - Perform a Set_Report transfer of a Feature report.
HIDIOCGFEATURE - Perform a Get_Report transfer of a Feature report.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hid-multitouch: minor fixes based on additional review
HID: Switch turbox/mosart touchscreen to hid-mosart
HID: add Add Cando touch screen 10.1-inch product id
HID: hid-mulitouch: add support for the 'Sensing Win7-TwoFinger'
HID: hid-multitouch: add support for Cypress TrueTouch panels
HID: hid-multitouch: support for PixCir-based panels
HID: set HID_MAX_FIELD at 128
HID: add feature_mapping callback
This device used the MULTI_INPUT quirk whereas it could be used
with hid-mosart instead to support the multitouch part.
Reference: https://bugs.launchpad.net/ubuntu/+bug/620609/
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch doesn't alter functionality, but removes a dedicated kernel
thread.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Maulik Mankad <x0082077@ti.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Neaten current uses of dev_<level> by adding and using
hid specific hid_<level> macros.
Convert existing uses of dev_<level> uses to hid_<level>.
Convert hid-pidff printk uses to hid_<level>.
Remove err_hid and use hid_err instead.
Add missing newlines to logging messages where necessary.
Coalesce format strings.
Add and use pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Other miscellaneous changes:
Add const struct hid_device * argument to hid-core functions
extract() and implement() so hid_<level> can be used by them.
Fix bad indentation in hid-core hid_input_field function
that calls extract() function above.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, if the device has been removed before hiddev_ioctl(),
the -EIO is returned. If it's removed while hiddev_ioctl() is in
progress, some commands are still processed fine, others
return -ENODEV. This change takes the "existancelock" before
processing ioctl commands and releases it at the end.
If the device has been removed, always returns -ENODEV.
Signed-off-by: Valentine Barshak <vbarshak@mvista.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A USB HID device can be disconnected at any time.
If this happens right before or while hiddev_ioctl is in progress,
the hiddev_ioctl tries to access invalid hiddev->hid pointer.
When the hid device is disconnected, the hiddev_disconnect()
ends up with a call to hid_device_release() which frees
hid_device, but doesn't set the hiddev->hid pointer to NULL.
If the deallocated memory region has been re-used by the kernel,
this can cause a crash or memory corruption.
Since disconnect can happen at any time, we can't initialize
struct hid_device *hid = hiddev->hid at the beginning of ioctl
and then use it.
This change checks hiddev->exist flag while holding
the existancelock and uses hid_device only if it exists.
Signed-off-by: Valentine Barshak <vbarshak@mvista.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for the media keys of the Perixx PERIBOARD-707 (Plus)
keyboard / remote control.
Signed-off-by: Dennis Kügler <dennis.kuegler@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Changed Makefile to use <modules>-y instead of <modules>-objs because -objs is
deprecated and should now be switched. According to (documentation/kbuild/makefiles.txt).
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
This device generates ABS_Z and ABS_RX events, while it should be
generating ABS_X and ABS_Y instead. Using the MULTI_INPUT quirk solves
this issue.
Reference: https://bugs.launchpad.net/ubuntu/+bug/620609/
Signed-off-by: Pierre BAILLY <pierre@substantiel.fr>
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes three problems with the eGalax/DWAV multi-touch
screen found in the Eee PC T101MT:
1) While there is a dedicated multitouch driver for the screen
(hid-egalax.c), the MULTI_INPUT quirk is also applied, preventing
the hid-egalax driver from working. This patch removes the quirk
so the hid-egalax driver can handle the device correctly.
2) The x and y coordinates sent by the screen in multi-touch mode are
shifted by three bits from the events sent in single-touch mode, thus
the coordinates are out of range, leading to the pointer being stuck
in the bottom-right corner if no additional calibration is applied
(e.g. in the X evdev driver). This patch shifts the coordinates back.
This does not decrease accuracy as the last three bits of the "wrong"
coordinates are always 0.
3) Only multi-touch pressure events are sent, single touch emulation is
missing pressure information. This patch adds single-touch
ABS_PRESSURE events.
Signed-off-by: Philipp Merkel <mail@philmerk.de>
Acked-by: Stéphane Chatty <chatty@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds the NOGET quirk for AXIS 295 Video Surveillance Joystick
(despite AXIS brand the vendor is actually CH Products). Without the quirk, the
joystick is detected but does not generate any events.
Signed-off-by: Rok Mandeljc <rok.mandeljc@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that hiddev_driver isn't being used for anything, there's no
reason to keep it around. This patch (as1419) gets rid of it
entirely.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Feature reports should only be sent on the control endpoint.
The USB HID standard is unclear and confusing on this issue. It seems to
suggest that Feature reports can be sent on a HID device's Interrupt OUT
endpoint. This cannot be the case because the report type is not encoded in
transfers sent out the Interrput OUT endpoint. If Feature reports were sent on
the Interrupt OUT endpint, they would be indistinguishable from Output reports
in the case where Report IDs were not used.
Further, Windows and Mac OS X do not send Feature reports out the interrupt OUT
Endpoint. They will only go out the Control Endpoint.
In addition, many devices simply do not hande Feature reports sent out the
Interrupt OUT endpoint.
Reported-by: simon@mungewell.org
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
My macbook infrared remote control was broken by commit
bd25f4dd69 ("HID: hiddev: use
usb_find_interface, get rid of BKL").
This device appears in dmesg as:
apple 0003:05AC:8242.0001: hiddev0,hidraw0: USB HID v1.11 Device
[Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-1/input0
It stopped working as lircd was getting ENODEV when opening /dev/usb/hiddev0.
AFAICS hiddev_driver is a dummy driver so usb_find_interface(&hiddev_driver)
does not find anything.
The device is associated with the usbhid driver, so let's do
usb_find_interface(&hid_driver) instead.
$ ls -l /sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0/usb/hiddev0/device/driver
lrwxrwxrwx 1 root root 0 2010-09-12 16:28 /sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0/usb/hiddev0/device/driver -> ../../../../../../bus/usb/drivers/usbhid
Signed-off-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add no-get quirk for eGalax touch controller to avoid timeout at probe.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for Waltop Media Tablet 14.1 inch by fixing report descriptor.
This tablet is also sold as Genius G-Pen M712 (older version) and M712X
(newer version). Both are supported.
Trust Wide Screen Design Tablet (TB-7300, item no 15358) seems to be the
older version of this tablet (similar to Genius G-Pen M712), and could be
supported as well.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds a quirk for the eGalax touch controller which reports
two pairs of axes.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When I made commit 29129a98e6 ("HID: Send Report ID when numbered
reports are sent over the control endpoint"), I didn't account for *buf
not being the report ID anymore, as buf is incremented.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Kanvus Note A5 tablet (with USB ID 5543:6001, USB vendor UC_Logic) needs
the HID_QUIRK_MULTI_INPUT in order to work out of the box; otherwise, we get
the usual "cursor stuck at the upper left corner of the screen".
Signed-off-by: Decio Fonini <fonini@techk.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for Waltop Slim Tablet 5.8 inch and Media Tablet 10.6 inch.
These (and other Waltop) tablets are usually sold by different companies
(such as Genius and Trust) and with different names, but with the same USB
vendor/product IDs.
Slim Tablet 5.8 inch is known to also be sold as Genius G-Pen F350 and Trust
Widescreen Mini Tablet (item no 16485).
Media Tablet 10.6 inch is known to also be sold as Genius G-Pen M609 and
M609X. Of these only the latter is known to be supported.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds a hid quirk for the chicony multitouch screen found in the Acer
Aspire 1820pt notebook.
Signed-off-by: David Gow <david@ingeniumdigital.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit bd25f4dd69 ("HID: hiddev: use usb_find_interface,
get rid of BKL") introduced using of private intfdata in hiddev for
purpose of storing hiddev pointer.
This is a problem, because intf pointer is already being set to struct
hid_device pointer by HID core. This obviously lead to memory corruptions
at device disconnect time, such as
WARNING: at lib/kobject.c:595 kobject_put+0x37/0x4b()
kobject: '(null)' (ffff88011e9cd898): is not initialized, yet kobject_put() is being called.
Convert hiddev into accessing hiddev through struct hid_device which is
in intfdata already.
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-and-tested-by: Heinz Diehl <htd@fritha.org>
Reported-and-tested-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
One of our users reports consistently hitting a NULL dereference that
resolves to the "hid_to_usb_dev(hid);" call in hiddev_ioctl(), when
disconnecting a Lego WeDo USB HID device from an OLPC XO running
Scratch software. There's a FIXME comment and a guard against the
dereference, but that happens farther down the function than the
initial dereference does.
This patch moves the call to be below the guard, and the user reports
that it fixes the problem for him. OLPC bug report:
http://dev.laptop.org/ticket/10174
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for UC-Logic WP4030U, WP5540U and WP8060U tablets.
These tablets are usually sold by Genius, Trust and possibly others under
different names and in different cases, but with the original USB
vendor/product IDs.
Currently, these tablets are supported by standalone X.org driver WizardPen.
This patch aims to fix them in the kernel and make them supported by the
generic evdev X.org driver. Still, some minor fixes in the X.org driver are
to be made for the full stack support.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These devices report a usage page of type "consumer" and a usage of
"Programmable buttons". They are hence ignored by the hid-input layer.
Force the registration of an input device by using the new quirk type
HID_QUIRK_HIDINPUT_FORCE.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This removes the private hiddev_table in the usbhid
driver and changes it to use usb_find_interface
instead.
The advantage is that we can avoid the race between
usb_register_dev and usb_open and no longer need the
big kernel lock.
This doesn't introduce race condition -- the intf pointer could be
invalidated only in hiddev_disconnect() through usb_deregister_dev(),
but that will block on minor_rwsem and not actually remove the device
until usb_open().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: "Greg Kroah-Hartman" <gregkh@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Report ID wasn't sent as part of the payload for reports which were sent
over the control endpoint. This is required by section 8.1 of the HID spec.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Patch for linux-2.6.35-rc4 mainline kernel to enable Paul Qureshi's
Retro Adapter [http://keio.dk/retroadapter.html], an open source USB
device which allows controllers and joysticks from classic computers
and consoles to work on modern PCs, to appear as two separate devices
under Linux.
Signed-off-by: Peter Edwards <samwise@bagshot-row.org>
Acked-by: Paul Qureshi <retro@world3.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This USB flight yoke needs the NOGET quirk, like most of CH's other
products. This patch adds that.
Signed-off-by: Jonathan Rockway <jon@jrock.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1350) removes all usages of coherent buffers for USB
control-request setup-packet buffers. There's no good reason to
reserve coherent memory for these things; control requests are hardly
ever used in large quantity (the major exception is firmware
transfers, and they aren't time-critical). Furthermore, only seven
drivers used it. We might as well always use streaming DMA mappings
for setup-packet buffers, and remove some extra complexity from
usbcore.
The DMA-mapping portion of hcd.c is currently in flux. A separate
patch will be submitted to remove support for URB_NO_SETUP_DMA_MAP
after everything else settles down. The removal should go smoothly,
as by then nobody will be using it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the hidraw driver use the first Interrupt OUT endpoint for
HID transfers to the device if such an endpoint exists. This is consistent
with the behavior of the hiddev driver, and the logic is similar.
From the USB HID specification:
The Interrupt Out pipe is optional. If a device declares an Interrupt Out
endpoint then Output reports are transmitted by the host to the device
through the Interrupt Out endpoint. If no Interrupt Out endpoint is
declared then Output reports are transmitted to a device through the
Control endpoint, using Set_Report(Output) requests.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I've got one of these devices on my desk and it seems that it suffers from
the ABS_Z/ABS_RX issue that we've seen in other devices before. This patch
uses the same reasoning as 9db630b48 ("HID: add multi-input quirk for NextWindow
Touchscreen").
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Although the usbhid driver allocates its usbhid structure in the probe
routine, several critical fields in that structure don't get
initialized until usbhid_start(). However if report descriptor
parsing fails then usbhid_start() is never called. This leads to
problems during system suspend -- the system will freeze.
This patch (as1378) fixes the bug by moving the initialization
statements up into usbhid_probe().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-By: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add suspend/resume hooks for HID drivers so these can do some
additional state adjustment when device gets suspended/resumed.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add two quirks to make it possible for usbhid module options to
override whether a device is ignored (HID_QUIRK_NO_IGNORE) and
whether to connect a hiddev device (HID_QUIRK_HIDDEV_FORCE).
Passing HID_QUIRK_NO_IGNORE for your device means that it will
not be ignored by the HID layer, even if present in a blacklist.
HID_QUIRK_HIDDEV_FORCE will force the creation of a hiddev for that
device, making it accessible from user-space.
Tested with an Apple IR Receiver, switching it from using appleir
to using lirc's macmini driver.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as1365) enables remote wakeup by default for USB keyboard
devices. Keyboards in general are supposed to be wakeup devices, but
the correct place to enable it depends on the device's bus; no single
approach will work for all keyboard devices. In particular, this
covers only USB keyboards (and then only those supporting the boot
protocol).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add framebuffer support to PicoLCD device with use of deferred-io.
Only changed areas of framebuffer get sent to device in order to
save USB bandwidth and especially resources on PicoLCD device or
allow higher refresh rate for a small area. Changed tiles are
determined while updating shadow framebuffer.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Move the initialization of USB interface pointers from _start()
over to _probe() callback, which is where it belongs.
This fixes case where interface is NULL when parsing of report
descriptor fails.
LKML-Reference: <20100213135720.603e5f64@neptune.home>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some devices do not react to a control request (seen on APC UPS's) resulting in
a slow stream of messages, "generic-usb ... control queue full". Therefore
request needs a timeout.
Cc: stable@kernel.org
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device generates ABS_Z and ABS_RX events, while it should be
generating ABS_X and ABS_Y instead. Using the MULTI_INPUT quirk solves
this issue.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Daniel Oliveira Nascimento <don@syst.com.br>
[jkosina@suse.cz: fixed blacklist ordering while resolving conflict]
[jkosina@suse.cz: fixed typo to make it compile]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In commit 2da31939a4 ("Bluetooth: Implement raw output support for HIDP
layer"), support for Bluetooth hid_output_raw_report was added, but it
pushes the data to the intr socket instead of the ctrl one. This has been
fixed by 6bf8268f9a ("Bluetooth: Use the control channel for raw HID reports")
Still, it is necessary to distinguish whether the report in question should be
either FEATURE or OUTPUT. For this, we have to extend the generic HID API,
so that hid_output_raw_report() callback provides means to specify this
value so that it can be passed down to lower level hardware drivers (currently
Bluetooth and USB).
Based on original patch by Bastien Nocera <hadess@hadess.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device generates ABS_Z and ABS_RX events, while it should be
generating ABS_X and ABS_Y instead. Using the MULTI_INPUT quirk solves
this issue.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Daniel Oliveira Nascimento <don@syst.com.br>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I happen to own a keyboard identified as 05af:3062 which is labeled as
"FlatX Coldless Combo" by "Prodige", which exhibits input problems without
NOGET quirk. For some reason, lsusb reports this device as "Jing-Mold
Enterprise Co., Ltd", which is not mentioned anywhere on the package.
A quick search on the intenet shows that there a other people who have
this in their lsusb output, but apparently they don't have the problem
I am seeing (or they are not such furious typists as myself).
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as1302) removes the auto_pm flag from struct usb_device.
The flag's only purpose was to distinguish between autosuspends and
external suspends, but that information is now available in the
pm_message_t argument passed to suspend methods.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: appletouch - give up maintainership
Input: dm355evm_kbd - switch to using sparse keymap library
Input: wistron_btns - switch to using sparse keymap library
Input: add generic support for sparse keymaps
Input: fix memory leak in force feedback core
Input: wistron - remove identification strings from DMI table
Input: psmouse - remove identification strings from DMI tables
Input: atkbd - remove identification strings from DMI table
Input: i8042 - remove identification strings from DMI tables
DMI: allow omitting ident strings in DMI tables
Input: psmouse - do not carry DMI data around
Input: matrix-keypad - switch to using dev_pm_ops
Input: keyboard - fix lack of locking when traversing handler->h_list
Input: gpio_keys - scan gpio state at probe and resume time
Input: keyboard - add locking around event handling
Input: usbtouchscreen - add support for ET&T TC5UH touchscreen controller
Input: xpad - add two new Xbox 360 devices
Input: polled device - do not start polling if interval is zero
Input: polled device - schedule first poll immediately
Input: add S3C24XX touchscreen driver
...
These touchscreens are mounted onto HP TouchSmart and the Dell Studio One
19. Without a quirk they report a wrong button set and the x/y coordinates
through ABS_Z/ABS_RX, confusing the higher levels (most notably X.Org's
evdev driver).
Device id 0x003 covers models 1900, 2150, and 2700 [1] though testing could
only be performed on a model 1900.
[1] http://www.nextwindow.com/nextwindow_support/latest_tech_info.html
Signed-off-by: Peter Hutterer <peter.hutterer@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use strlcat() to append a string to the previously created first part.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The race between ioctl and disconnect is guarded by low level
hiddev device mutex (existancelock) since the commit
07903407 ("HID: hiddev cleanup -- handle all error conditions
properly"), therefore we can remove the lock_kernel() from
hiddev_ioctl_usage().
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
NCR devices are terminally broken by design -- they claim themselves to contain
proper input applications in their HID report descriptor, but behave very badly
if treated in standard way.
According to NCR developers, the devices get confused when queried for reports
in a standard way, rendering them unusable.
NCR is shipping application called "RPSL" that can be used to drive these
devices through hiddev, under the assumption that in-kernel driver doesn't
perform initial report query.
If it does, neither in-kernel nor hiddev-based driver can operate with these
devices any more.
Introduce a quirk that skips the report query for all NCR devices. The previous
NOGET quirk was wrong and had been introduced because I misunderstood the nature
of brokenness of these devices.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When encountering a strange value in the pool report, pidff_reset
will always refetch the report 20 times, even if one of the retries
results in a sane value. This is because a temporary variable being
used to store the value is not being updated inside the loop.
Fix it by using the value directly in the loop.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch was applied to Fedora 11's 2.6.30.8-64 kernel and adds the
NOGET quirk for CH Products industrial class joystick(s). It is like
the previous CH Products NOGET quirk patch for their consumer class
joysticks. Without the quirk, the joystick would only be detected and
would not function at all in kernels >= 2.6.29. It was tested with a CH
Products 3-axis 5-button industrial joystick, product #HG-434IS000-U-217.
Signed-off-by: Keith Rutkowski <rutkowski@signatureresearchinc.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove unused (in usbhid module) DRIVER_AUTHOR macrco and properly
use multiple MODULE_AUTHOR() instances in both modules.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This allows subsytems to provide devtmpfs with non-default permissions
for the device node. Instead of the default mode of 0600, null, zero,
random, urandom, full, tty, ptmx now have a mode of 0666, which allows
non-privileged processes to access standard device nodes in case no
other userspace process applies the expected permissions.
This also fixes a wrong assignment in pktcdvd and a checkpatch.pl complain.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
HID core registers input, hidraw and hiddev devices, but leaves
unregistering it up to the individual driver, which is not really nice.
Let's move all the logic to the core.
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Reported-by: Brian Rogers <brian@xyzw.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hiddev userspace driver uses a rignbuffer to store the parsed usages
that should be returned through read(). This buffer is 64 bytes long,
which is sufficient for queueing single USB 1.0 low-speed report, which
is of maximum size 48 bytes.
There are however USB HID devices which are full-speed USB devices, and
therefore they are free to produce reports 64 bytes long. This is correctly
handled by HID core, but read() on hiddev node gets stuck forever, because
the ring buffer loops infinitely (as it is exactly 64 bytes long as well),
never advancing the buffer pointer.
Plus, the core driver is ready to handle highspeed devices, so we should be
able to handle reports from such devices in the hiddev driver as well, which
means we need larger ringbuffer.
Reported-by: Michael Zeisel <michael.zeisel@philips.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
__usbhid_submit_report() is a local function wrapped by the exported
symbol usbhid_submit_report(). As such, it should be static.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Check whether index is within bounds before testing the element.
declared in drivers/hid/usbhid/hid-core.c:62:
static char *quirks_param[MAX_USBHID_BOOT_QUIRKS] = ...
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for USB drivers to report their requested nodename to
userspace. It also updates a number of USB drivers to provide the
needed subdirectory and device name to be used for them.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is a little bit inconvenient for people who have some non-standard
HID hardware (usually violating the HID specification) to have to
recompile kernel with CONFIG_HID_DEBUG to be able to see kernel's perspective
of the HID report descriptor and observe the parsed events. Plus the messages
are then mixed up inconveniently with the rest of the dmesg stuff.
This patch implements /sys/kernel/debug/hid/<device>/rdesc file, which
represents the kernel's view of report descriptor (both the raw report
descriptor data and parsed contents).
With all the device-specific debug data being available through debugfs, there
is no need for keeping CONFIG_HID_DEBUG, as the 'debug' parameter to the
hid module will now only output only driver-specific debugging options, which has
absolutely minimal memory footprint, just a few error messages and one global
flag (hid_debug).
We use the current set of output formatting functions. The ones that need to be
used both for one-shot rdesc seq_file and also for continuous flow of data
(individual reports, as being sent by the device) distinguish according to the
passed seq_file parameter, and if it is NULL, it still output to kernel ringbuffer,
otherwise the corresponding seq_file is used for output.
The format of the output is preserved.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
No more reinitialization is needed in the post reset hook, remove
the FIXME comment.
While at it, clean up whitespaces in the immediate surrounding.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as1240) adds the NOGET quirk for three devices from CH
Products: the Pro pedals, the Combatstick joystick, and the Flight-Sim
yoke. Without these quirks, the devices haven't worked for many
kernel releases. Sometimes replugging them after boot-up would get
them to work and sometimes they wouldn't work at all.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Sean Hildebrand <silverwraithii@gmail.com>
Reported-by: Sid Boyce <sboyce@blueyonder.co.uk>
Tested-by: Sean Hildebrand <silverwraithii@gmail.com>
Tested-by: Sid Boyce <sboyce@blueyonder.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Device-specific quirks are set up correctly in their respective vendor-specific
driver, then get overwritten in usbhid_parse().
This is only issue for device-specific NOGET quirks being set by driver for a
few devices out there.
Signed-off-by: Zoltan Karcagi <zkr@freemail.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch switches usbhid_close() from flush_scheduled_work() to canceling
the outstanding work. This fixes a possible deadlock due to work taking
the mutex usbhid_close() holds. Lockdep reported the problem.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
--
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
upon further thought this code is still racy.
retval = usb_register_dev(usbhid->intf, &hiddev_class);
here you open a window during which open can happen
if (retval) {
err_hid("Not able to get a minor for this device.");
hid->hiddev = NULL;
kfree(hiddev);
return -1;
} else {
hid->minor = usbhid->intf->minor;
hiddev_table[usbhid->intf->minor - HIDDEV_MINOR_BASE] = hiddev;
and will fail because hiddev_table hasn't been updated
The obvious fix of using a mutex to guard hiddev_table doesn't work because
usb_open() and usb_register_dev() take minor_rwsem and we'd have an AB-BA
deadlock. We need a lock usb_open() also takes in the right order and that leaves
only one option, BKL. I don't like it but I see no alternative.
Once the usb_open() implements something better than lock_kernel(), we could also
do so.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When hid quirks were converted to specialized driver, the HID_QUIRK_IGNORE
has been moved completely, as the hid_ignore_list[] has been moved into the
generic code.
However userspace already got used to the possibility that modprobing
usbhid with
'quirks=vid:pid:0x4'
makes the device ignored by usbhid driver. So keep this quirk flag in place
for backwards compatibility.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'bkl-removal' of git://git.lwn.net/linux-2.6:
Rationalize fasync return values
Move FASYNC bit handling to f_op->fasync()
Use f_lock to protect f_flags
Rename struct file->f_ep_lock
This fixes a use of flush_scheduled_work() in USB HID's reset logic that can
deadlock.
Tested-by: Valdis Kletniks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no point of having hid_reset_resume() when CONFIG_PM is
not set, and even the corresponding .reset_resume pointer in hid_driver
struct is properly ifdefed.
Move the definition into the ifdef CONFIG_PM part of the source to avoid
drivers/hid/usbhid/hid-core.c:1337: warning: 'hid_reset_resume' defined but not used
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes a bug caused by reset_resume not changing the internal
status flags for a device that is resumed via reset_resume. To do so the
reset handlers, which correctly assume that a device is awake, can no longer
do all the work of reset_resume handling.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fixes this build breakage in case when CONFIG_PM is not set
drivers/hid/usbhid/hid-core.c: In function 'hid_suspend':
drivers/hid/usbhid/hid-core.c:1220: error: 'struct usb_device' has no member named 'auto_pm'
drivers/hid/usbhid/hid-core.c:1245: error: 'struct usb_device' has no member named 'auto_pm'
drivers/hid/usbhid/hid-core.c:1258: error: 'struct usb_device' has no member named 'auto_pm'
by throwing both the hid_suspend() and hid_resume() away completely
in such case, as they won't be used anyway.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This uses the USB busy mechanism for aggessive autosuspend of USB
HID devices. It autosuspends all opened devices supporting remote wakeup
after a timeout unless
- output is being done to the device
- a key is being held down (remote wakeup isn't triggered upon key release)
- LED(s) are lit
- hiddev is opened
As in the current driver closed devices will be autosuspended even if they
don't support remote wakeup.
The patch is quite large because output to devices is done in hard interrupt
context meaning a lot a queuing and locking had to be touched. The LED stuff
has been solved by means of a simple counter. Additions to the generic HID code
could be avoided. In addition it now covers hidraw. It contains an embryonic
version of an API to let the generic HID code tell the lower levels which
capabilities with respect to power management are needed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Most fasync implementations do something like:
return fasync_helper(...);
But fasync_helper() will return a positive value at times - a feature used
in at least one place. Thus, a number of other drivers do:
err = fasync_helper(...);
if (err < 0)
return err;
return 0;
In the interests of consistency and more concise code, it makes sense to
map positive return values onto zero where ->fasync() is called.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
DECLARE_WAITQUEUE doesn't initialize the wait descriptor's task_list
to 'empty' but to zero.
prepare_to_wait() will not enqueue the descriptor to the waitqueue and
finish_wait() will do list_del_init() on a list head that contains
NULL pointers, which oopses.
This was introduced by 079034073 "HID: hiddev cleanup -- handle all
error conditions properly".
The prior code used an unconditional add_to_waitqueue() which didn't
care about the wait descriptor's list head and enqueued the thing
unconditionally.
The new code uses prepare_to_wait() which DOES check the prior list
state, so use DEFINE_WAIT instead.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If hiddev_open() fails, it wrongly frees the shared hiddev structure
kept in hiddev_table instead of the hiddev_list structure allocated
for the opened file descriptor. Existing references to this structure
will then accessed free memory.
This was introduced by 079034073 "HID: hiddev cleanup -- handle all
error conditions properly".
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The logic for testing for disconnection is reversed in an ioctl leading
to false reports of disconnection.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Folkert van Heusden <folkert@vanheusden.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (123 commits)
wimax/i2400m: add CREDITS and MAINTAINERS entries
wimax: export linux/wimax.h and linux/wimax/i2400m.h with headers_install
i2400m: Makefile and Kconfig
i2400m/SDIO: TX and RX path backends
i2400m/SDIO: firmware upload backend
i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends
i2400m/SDIO: header for the SDIO subdriver
i2400m/USB: TX and RX path backends
i2400m/USB: firmware upload backend
i2400m/USB: probe/disconnect, dev init/shutdown and reset backends
i2400m/USB: header for the USB bus driver
i2400m: debugfs controls
i2400m: various functions for device management
i2400m: RX and TX data/control paths
i2400m: firmware loading and bootrom initialization
i2400m: linkage to the networking stack
i2400m: Generic probe/disconnect, reset and message passing
i2400m: host/device procotol and core driver definitions
i2400m: documentation and instructions for usage
wimax: Makefile, Kconfig and docbook linkage for the stack
...
Commit 079034073f ("HID: hiddev cleanup -- handle all error conditions
properly") by mistake removed proper initialization of hid->hiddev pointer
in hiddev_connect() in case usb_register_dev() succeeds for the hiddev node.
Put it properly back in place.
Reported-and-tested-by: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1161) changes the interface to
usb_lock_device_for_reset(). The existing interface is apparently not
very clear, judging from the fact that several of its callers don't
use it correctly. The new interface always returns 0 for success and
it always requires the caller to unlock the device afterward.
The new routine will not return immediately if it is called while the
driver's probe method is running. Instead it will wait until the
probe is over and the device has been unlocked. This shouldn't cause
any problems; I don't know of any cases where drivers call
usb_lock_device_for_reset() during probe.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Genius PenSketch 12x9 tablet has a puck (labeled a
"Tablet Mouse") in addition to a pen. Without registering a quirk
the tablet appears to be a single input device that reports the
wrong axis information in /proc/bus/input/devices, and sends
incorrect events (e.g. ABS_Z instead of ABS_Y). This information
confuses the X evdev driver and makes the device impossible to
use.
The quirk fixes events and splits the device into multiple input
event devices so that at least the puck is useful.
Signed-off-by: Matt Helsley <matt.helsley@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The usbmouse and usbkbd modules are not supposed to be used with regular USB
mice and keyboards. Make them depend on EMBEDDED to prevent them from being
built and loaded on non-EMBEDDED configs.
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a cleanup of hiddev and fixes the following issues:
- thread safety by locking in read & ioctl, introducing a per device mutex
- race between ioctl and disconnect, introducing a flag and locking
in form of a per low level device mutex
- race between open and other methods, making sure only successfully
opened devices are put on the list, changing order of events
- range checking both upper and lower limits of the minor range
- make sure further calls to open fail for unplugged devices even if
the device still has opened files
- error checking for low level open
- possible loss of wakeup events, using standard waiting macros
- race in initialisation by moving registration after full initialisation
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We might sleep, so no problem to use GFP_KERNEL.
While at it bring the function to coding style.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use usb_endpoint_xfer_int() instead of direct use of constants.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move usbhid specific flags from global hid.h into local usbhid.h.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as1146c) makes usbhid automatically call usbhid_set_leds()
for any device that supports the keyboard boot protocol.
In theory this should be perfectly safe. BIOSes send the LED output
report as part of their normal device initialization, so any keyboard
device supporting the boot protocol has to be able to handle it.
As a side effect, the hid-dell and hid-bright drivers are no longer
needed, and the Logitech keyboard driver can be removed from hid-lg.
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When computing the maximal buffer size needed, we must take into
account that not only input reports can be numbered.
Pointed out in bugzilla #10467
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It causes recursive locking warning and is unneeded after
introduction of STARTED flag.
* Resume vs. stop is effectively solved by DISCONNECT flag.
* No problem in suspend vs. start -- urb is submitted even after open
which is possible after connect which is called after start.
* Resume vs. start solved by STARTED flag.
* Suspend vs. stop -- no problem in killing urb and timer twice.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some devices have no input interrupt endpoint. These won't be handled
by usbhid, but currently they are not refused and reside on hid bus.
Perform this checking earlier so that we refuse to control such
a device early enough (and not pass it to the hid bus at all).
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
`stop' left out usbhid->urb* pointers and so the next `start' thought
it needs to allocate nothing and used the memory pointers previously
pointed to. This led to memory corruption and device malfunction.
Also don't forget to clear disconnect flag on start which was left set
by the previous `stop'.
This fixes
echo DEVICE > /sys/bus/hid/drivers/DRIVER/unbind
echo DEVICE > /sys/bus/hid/drivers/DRIVER/bind
failures.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When suspending, make sure that the timer is not running
any more.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Usbhid structure is allocated on start invoked only from probe
of some driver. When there is no driver, the structure is null
and causes null-dereference oopses.
Fix it by allocating the structure on probe and disconnect of
the device itself. Also make sure we won't race between start
and resume or stop and suspend respectively.
References: http://bugzilla.kernel.org/show_bug.cgi?id=11827
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Andreas Schwab <schwab@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Add support for Sony Vaio VGX-TP1E
HID: fix lock imbalance in hiddev
HID: fix lock imbalance in hidraw
HID: fix hidbus/appletouch device binding regression
HID: add hid_type to general hid struct
HID: quirk for OLED devices present in ASUS G50/G70/G71
HID: Remove "default m" for Thrustmaster and Zeroplus
HID: fix hidraw_exit section mismatch
HID: add support for another Gyration remote control
Revert "HID: Invert HWHEEL mappings for some Logitech mice"
Add type to the hid structure to distinguish to which device type
(now only mouse) we are talking to. Needed for per device type ignore
list support.
Note: this patch leaves the type as unknown for bluetooth devices,
there is not support for this in the hidp code.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There were two stragglers that got missed in the last merge of the HID tree that forgot to change the warn() calls to dev_warn(). This patch fixes them up.
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 8006479c9b introduced a spinlock in
input_dev->event_lock, which is locked when handling input events.
However, the hid-pidff driver sleeps when handling events as it waits for
reports being sent to the device before changing the report contents
again.
This causes a system lockup when trying to use force feedback with a PID
device, a regression introduced in 2.6.24 and 2.6.23.15.
Fix it by extracting the raw report data from struct hid_report
immediately when hid_submit_report() is called, therefore allowing
drivers to change the contents of struct hid_report immediately without
affecting the already-queued transfer.
In hid-pidff, re-add the removed usbhid_wait_io() to
pidff_erase_effect() instead, to prevent a full report queue from causing
the submission to fail, thus not freeing up device memory.
pidff_erase_effect() is not called while dev->event_lock is held.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid-ff.c now calls only pidff (generic driver), the special ones are now
in separate drivers. Invoke pidff on all non-special directly.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move the force feedback processing into a separate module.
[jkosina@suse.cz: fix Kconfig texts a little bit]
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This seems to be the very same device, as already supported Smartjoy
dual Plus, but with slightly different vendor ID. Let's support this
one too.
Reported-by: David Ashley <dashxdr@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Merge the logitech force feedback processing directly into logitech
driver from the usbhid core.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move the handling of the leds resetting from the core to
the dell and logitech drivers.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move connecting from usbhid to the hid layer and fix also hidp in
that manner.
This removes all the ignore/force hidinput/hiddev connecting quirks.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove support for both dynamic and static report descriptor
quirks. There is no longer rdesc code which it would support,
so it's useless.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Bring switch and cases into coding style and save thus some
indentation to make the code tighter.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move ignore quirks from usbhid-quirks into hid-core code. Also don't output
warning when ENODEV is error code in usbhid and try ordinal input in hidp
when that error is returned.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move ids from hid-quirks.c into separate file, since it will be needed in
more than one place.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Next step for complete hid bus, this patch includes:
- call parser either from probe or from hid-core if there is no probe.
- add ll_driver structure and centralize some stuff there (open, close...)
- split and merge usb_hid_configure and hid_probe into several functions
to allow hooks/fixes between them
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make a bus from hid core. This is the first step for converting all the
quirks and separate almost-drivers into real drivers attached to this bus.
It's implemented to change behaviour in very tiny manner, so that no driver
needs to be changed this time.
Also add generic drivers for both usb and bt into usbhid or hidp
respectively which will bind all non-blacklisted device. Those blacklisted
will be either grabbed by special drivers or by nobody if they are broken at
the very rude base.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver adds support for the multitouch trackpad on the new
Apple Macbook Air and Macbook Pro Penryn laptops. It replaces the
appletouch driver on those computers, and integrates well with the
synaptics driver of the Xorg system.
[dtor@mail.ru: various cleanups]
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch completely removes the dependency of usbkbd and usbmouse drivers
on usbhid code.
usbkbd/usbmouse drivers are not needed in the vast majority of cases anyway,
and they shouldn't be loaded in standard configurations at all. They are supposed
to be as trivial as possible, and searching for HID_QUIRK_IGNORE can even be
bad in some cases.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Logitech DiNovo desktop needs the same quirk as other DiNovo
devices.
Reported-by: Farid Benamrouche <farid.benamrouche@free.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When usbmouse/kbd is set to build, USB_HID is never defined due to
the USB_HID!=y Kconfig rule. Test CONFIG_USB_HID_MODULE in both
drivers instead.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some Logitech mice have a tilt wheel which register as HWHEEL buttons.
The events are positive for a click to the right and negative for a
click to the left. Applications expect the opposite, though.
I suspect this affects a lot more Logitech mice, but these are the only
two I have. I tested this using evtest and a GTK application. A similar
Microsoft Intellimouse I have works correctly.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added device ids to hid-quriks for detection of keyboards on 4th
generation Macbook Pro and Macbook Air
The naming scheme is consistent with past Apple keyboards in hid-quirks;
as defined by Apple (including device ids) in:
/System/Library/Extensions/AppleUSBTopCase.kext/Contents/PlugIns/AppleUSBTCKeyboard.kext/Co
ntents/Info.plist
Patch was originally posted and tested at:
https://bugs.launchpad.net/mactel-support/+bug/207127
Signed-off-by: Alexandre Karpenko <alexander@comm.utoronto.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix build failure introduced by Alan's ioctl -> unlocked_ioctl
(pushing BKL down to the driver) conversion patch for hiddev.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Push down the BKL. In some cases compat_ioctl already doesn't take the
BKL so we don't either. Some of the locking here seems already dubious
and object lifetimes want documenting
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch renames the existing usb_reset_device in hub.c to
usb_reset_and_verify_device and renames the existing
usb_reset_composite_device to usb_reset_device. Also the new
usb_reset_and_verify_device does't need to be EXPORTED .
The idea of the patch is that external interface driver
should warn the other interfaces' driver of the same
device before and after reseting the usb device. One interface
driver shoud call _old_ usb_reset_composite_device instead of
_old_ usb_reset_device since it can't assume the device contains
only one interface. The _old_ usb_reset_composite_device
is safe for single interface device also. we rename the two
functions to make the change easily.
This patch is under guideline from Alan Stern.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
From the current implementation of usb_reset_composite_device
function, the iface parameter is no longer useful. This function
doesn't do something special for the iface usb_interface,compared
with other interfaces in the usb_device. So remove the parameter
and fix the related caller.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The new iMON LCDs from SoundGraph need to be blacklisted from HID in order to
be used by lirc.
Signed-off-by: Dylan R Semler <dylan.semler@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since 2.6.25 the HID_QUIRK_APPLE_HAS_FN quirk is enabled even for
non-laptop Apple keyboards of the Aluminium series. The USB version of
these don't need Numlock emulation, like the laptop (and Aluminium
Wireless) do, as they have a proper keypad.
This patch splits the Numlock emulation for Apple keyboards in a
different quirk flag, so that it can be enabled for all the keyboards
but the Aluminium USB ones.
If the Numlock emulation is enabled for Aluminium USB keyboards, the
JKL and UIO keys become the numeric pad, and the rest of the keyboard
is disabled, included the key used to disable Numlock.
Additionally, these keyboard should not have a Numlock at all, as the
Numlock key is instead replaced by the 'Clear' key as usual for Apple
USB keyboards.
Signed-off-by: Diego 'Flameeyes' Petteno <flameeyes@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
usb_control_msg() converts arguments to little-endian itself,
doing that in caller means breakage on big-endian boxen.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a typo in report descriptor fixup, which results in improper
substitution and leaving old value in place.
Reported-by: Juha Motorsportcom <juha_motorsportcom@luukku.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Samsung USB remotes (0419:0001) report six keys via standard HID usage pages
(arrow keys, OK, Power). Kernel 2.6.25 maps those to input events (in addition
to the hiddev report). The remaining 43 keys are reported via proprietary HID
report page and therefore by hiddev only.
Applications using hiddev and input device might process the 6 standard keys
twice. To avoid this, the input device will be suppressed for the Samsung
remote with a quirk entry, forcing to use the hiddev device only.
LIRC already contains the proper support.
Signed-off-by: Robert Schedel <r.schedel@yahoo.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jeremy Robertson reports that GTCO engineers made a mistake and we don't
need 0x60x GTCO product ids blacklisted.
This mostly reverts dda3fd35, but leaves PID 0x1007 intact.
Reported-by: Jeremy Roberson <jeremy.roberson@einstruction.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no need to keep a few years old ThrustMaster force-feedback
driver as experimental.
HID_FF is currently marked experimental anyway, so this is even redundant.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a window:
task A task B
spin_lock_irq(&usbhid->inlock); /* Sync with error handler */
usb_set_intfdata(intf, NULL);
spin_unlock_irq(&usbhid->inlock);
usb_kill_urb(usbhid->urbin);
usb_kill_urb(usbhid->urbout);
usb_kill_urb(usbhid->urbctrl);
del_timer_sync(&usbhid->io_retry);
cancel_work_sync(&usbhid->reset_work);
if (!hid->open++) {
res = usb_autopm_get_interface(usbhid->intf);
if (res < 0) {
hid->open--;
return -EIO;
}
}
if (hid_start_in(hid))
if (hid->claimed & HID_CLAIMED_INPUT)
hidinput_disconnect(hid);
in which an open() to an already disconnected device will submit an URB
to an undead device. In case disconnect() was called by an ioctl, this'll
oops. Fix by introducing a new flag and checking it in hid_start_in().
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch makes the following needlessly global functions static:
- hid-core.c:hid_input_field()
- usbhid/hid-quirks.c:usbhid_modify_dquirk()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This moves the misplaced rdesc quirk to the place where it belongs.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add force feedback support for Logitech Rumblepad 2.
Tested-By: Edgar Simo <bobbens@gmail.com>
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix these sparse warnings:
.../hid/hid-core.c💯15: warning: incorrect type in assignment (different signedness)
.../hid/hid-core.c💯15: expected signed int [usertype] *value
.../hid/hid-core.c💯15: got unsigned int *<noident>
by unsigned -> s32
.../hid/hid-input-quirks.c:336:10: warning: Using plain integer as NULL pointer
by 0 -> NULL
.../hid/usbhid/hid-core.c:786:46: warning: incorrect type in argument 3 (different signedness)
.../hid/usbhid/hid-core.c:786:46: expected int *max
.../hid/usbhid/hid-core.c:786:46: got unsigned int *<noident>
.../hid/usbhid/hid-core.c:787:47: warning: incorrect type in argument 3 (different signedness)
.../hid/usbhid/hid-core.c:787:47: expected int *max
.../hid/usbhid/hid-core.c:787:47: got unsigned int *<noident>
.../hid/usbhid/hid-core.c:788:48: warning: incorrect type in argument 3 (different signedness)
.../hid/usbhid/hid-core.c:788:48: expected int *max
.../hid/usbhid/hid-core.c:788:48: got unsigned int *<noident>
by int -> unsigned int
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This must be the weirdest failure yet. My external disk stops processing
the storage commands the moment it receives a GET_REPORT. The firmware
does not crash; if I do rmmod hid, then SET-INTERFACE restores normal
operations. Still, I cannot live without the keyboard when I want backup
my files. Adding the NOGET quirk fixes this problem for me.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device has reports lower logical maximum compared to the real
usages for Zoom+ and Zoom- it emits.
This patch bumps the values in the report descriptor up, and also
adjusts HID_MAX_USAGE accordingly.
Reported-by: Khelben Blackstaff <eye.of.the.8eholder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Microsoft's wireless desktop receiver (Model 1028) has a bug in the report
descriptor -- namely, in four seperate places it uses USAGE_MIN and _MAX when
it quite obviously doesn't intend to.
In other words, it reports that it has pretty much _everything_ in 'consumer'
and 'generic desktop'. And then the X evdev driver believes I have a mouse
with 36 absolute axes and a huge pile of keys and buttons, when I in fact,
should have zero. 255/256 in three of the cases, and 0-1024 in another.
This patch fixes the report descriptor of this device before it enters the HID
parser.
Signed-off-by: Jim Duchek <jim.duchek@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many vendors highspeed devices give erroneously fullspeed interval value in
endpoint descriptor for interrupt endpoints. This quirk fixes up that by
recalculating the right value for highspeed device.
At the time of hid configuration this quirk calculates which highspeed interval
value gives same interval delay as, or next smaller then, what it would be if
the original value would be interpreted as fullspeed value. In subsequent urbs
that new value is used instead.
Forming the 'hid->name' in usb_hid_config() was moved up to accommodate more
descriptive printk reporting the fixup.
In this patch the quirk is set for one such device: Afatech DVB-T 2 infrared
HID-keyboard. It reports value 16 which means 4,069s in highspeed while
obviously 16ms was intended. In this case quirk calculates new value to be 8
which gives when interpreted as highspeed value 16ms as wanted. The behavior of
the device was verified to be what expected both before and after the patch.
Signed-off-by: Pekka Sarnila <sarnila@adit.fi>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix build failure in hiddev_ioctl with gcc 3.2:
http://bugzilla.kernel.org/show_bug.cgi?id=10121
The trick is to move the handling of ioctls which need to allocate
memory to separate functions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
USBHID driver only supports relative mode with this tablet so let aiptek
module handle it.
Signed-off-by: Dmitry Guryanov <guryanov@dgap.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add quirk entry for BADPAD for the NATSU Playstation USB adapter. The
adapter is supported under Linux, but with bad direction detection.
Signed-off-by: Andrew Burton <adb@iinet.net.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We need to blacklist this device, as it should be handled by
ldusb driver.
Reported-by: stephen <stephen.ware@eqware.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds new GTCO CalComp USB device PIDs to the blacklist.
Signed-off-by: Jeremy A. Roberson <jroberson@gtcocalcomp.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds blacklist entries in hid-quirks.c to let the usbhid driver
ignore the si470x radio devices. They are now handled by the new radio-si470x
driver.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Logitech Extreme 3D needs NOGET quirk, otherwise it times out at
the time of connect.
Reported-by: Mike Sharov <msharov@softhome.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Samsung USB remotes (0419:0001) are rejected by kernel 2.6.23, because the
report descriptor from the remote contains a 48 bit HID report field. HID 1.11
states: Fields may span at most 4 bytes.
This patch, based on 2.6.23, fixes this by modifying the internal report
descriptor in hid-quirks.c. Additional user space support (e.g. LIRC) is
required to fetch the information from the hiddev interface.
The burden to reconstruct the data is moved into userspace (lirc through hiddev).
There is no need to set HID_QUIRK_HIDDEV quirk, as the device has also output
applications, which trigger the creation of hiddev device automatically.
Signed-off-by: Robert Schedel <r.schedel@yahoo.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We can use the blacklist only if usbhid code is compiled.
Reported-by: jurriaan <thunder7@xs4all.nl>
Cc: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Gretag-Macbeth Huey display colorimeter claims to be an HID device but
isn't. As a result the linux HID device will claim it, preventing FLOSS
software like Argyll CMS from talking to it.
Tested-by: Frederic Crozat <fcrozat@mandriva.com>
Signed-off-by: Nicolas Mailhot <nicolas.mailhot@laposte.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The device is not discoverable, and needs to be poked to set its master, the
Bluetooth device it will try to connect to when the "Home" button is pressed
without a cable plugged in.
Using libusb means disconnecting the device from its driver to get the report
descriptor. Using hiddev, we can poke it without relinquishing control over it,
so when you plug it in, it would still work as a pad.
This could be then used by sixpair program, after it is rewritten to use
hiddev instead of libusb.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This fixes wacom tablets not working if usbmouse is loaded.
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This removes ugly macros IS_* to distinguish devices that
need special handling in hid-input, and establish proper
quirks for them.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
BTC 8193 keyboard handles its scrollwheel in very non-standard way.
It produces two non-standard usages for scrolling up and down, in
both cases with postive value equaling to 1. We handle this by temporary
mapping, which we then catch in quirk event handler, and remap to
negative HWHEEL even in order to introduce correct behavior.
Also the button requires special mapping, as it triggers standard-violating
usage code.
Reported in kernel.org bugzilla #9385
Reported-by: Kir Kolyshkin <kir@sacred.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make the Microsoft Wireless Optical Desktop 3.0 work as a mouse.
Microsoft Wireless Optical Desktop 3.0 doesn't properly describe its interface
class. Specifically, since it doesn't mark the second interface as a mouse
(bInterfaceSubclass = 0), it doesn't get HID_QUIRK_NOGET applied to the
interface, and then acts broken when polled.
Signed-off-by: Drew Fisher <drew.m.fisher@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reuse the quirks from the Cordless Desktop LX500 - stops some of the extra
keys being reported as mouse buttons.
Signed-off-by: Carlos Corbacho <cathectic@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Genius KB-29E has broken report descriptor, which causes some of the
Consumer usages to appear incorrectly as Button usages. We fix it by
fixing the report descriptor before it is being parsed.
Also a few of the keys violate the HUT standard, so they need a special
handling. They currently fall into "Reserved" range as per HUT 1.12.
Reported-by: Szekeres Istvan <szekeres@iii.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Don't directly cast list_head * to foo *, this works only when list
is the first member of struct foo, and we should not make the assumption
how members are ordered in the structure.
i.e. struct *f = (struct *f)pos will work if:
struct foo {
struct list_head list;
int i;
};
but will fail if:
struct foo {
int i;
struct list_head list;
}
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This mouse distinguishes horizontal wheel from vertical by a special "pseudo
event" GenericDesktop.00b8, with values of 0 for vertical and 8 for horizontal
wheel. Because this event is supplied by the parser too late, we need to delay
a wheel event, wait for this one and send either REL_WHEEL or REL_HWHEEL to
input depending on the event value.
Signed-off-by: Pavel Troller <patrol@sinus.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reuse the existing quirks for Apple laptop USB keyboards.
Signed-off-by: Michel Daenzer <michel@tungstengraphics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Preserve identifiers exposed in build and run time configuration though in
order not to break existing configurations.
This is in preparation for adding support for Apple aluminum USB keyboards.
Signed-off-by: Michel Daenzer <michel@tungstengraphics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
drivers/hid/usbhid/hiddev.c: In function 'hiddev_compat_ioctl':
drivers/hid/usbhid/hiddev.c:746: warning: passing argument 4 of 'hiddev_ioctl' makes
integer from pointer without a cast
Add cast to hiddev_compat_ioctl()
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Changed email address of Johann Deneux (myself)
Also removed CVS tags in comments (no longer using cvs)
Signed-off-by: Johann Deneux <johann.deneux@gmail.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
get rid of input BIT* duplicate defines
use newly global defined macros for input layer. Also remove includes of
input.h from non-input sources only for BIT macro definiton. Define the
macro temporarily in local manner, all those local definitons will be
removed further in this patchset (to not break bisecting).
BIT macro will be globally defined (1<<x)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: <dtor@mail.ru>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Cc: <lenb@kernel.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: <perex@suse.cz>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <vernux@us.ibm.com>
Cc: <malattia@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hidraw is an interface that is going to obsolete hiddev one
day.
Many userland applications are using libusb instead of using
kernel-provided hiddev interface. This is caused by various
reasons - the HID parser in kernel doesn't handle all the
HID hardware on the planet properly, some devices might require
its own specific quirks/drivers, etc.
hiddev interface tries to do its best to parse all the received
reports properly, and presents only parsed usages into userspace.
This is however often not enough, and that's the reason why
many userland applications just don't use hiddev at all, and
rather use libusb to read raw USB events and process them on
their own.
Another drawback of hiddev is that it is USB-specific.
hidraw interface provides userspace readers with really raw HID
reports, no matter what the low-level transport layer is (USB/BT),
and gives the userland applications all the freedom to process
the HID reports in a way they wish to.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hiddev driver currently lacks 32bit ioctl compatibility, so
if you're running with a 64bit kernel and 32bit userspace, it won't
work.
I'm pretty sure that the only thing missing is a compat_ioctl
implementation as all structs have fixed size fields.
With this change I can use revoco to configure my MX Revolution mouse.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes the problem, that Japanese MacBook doesn't recognize some keys
like '\'(yen, or backslash), '|'(pipe), and '_'(underscore).
It is due to that MacBook JIS keyboard (jp106) sends wrong report descriptor.
It saids "logical maximum = 0x65", so Keyboard.0089 is mapped to Key.Unknown,
while it should be accepted as Key.Yen.
Signed-off-by: Tomoya Adachi <adachi@il.is.s.u-tokyo.ac.jp>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add 0e8f:0003 into the list of devices supported by the hid-plff
force feedback driver. These devices identify themselves as
"GreenAsia Inc. USB Joystick " and can be either adapters or
actual game controllers. The testing was done with a Köng Gaming
gamepad.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use HID_QUIRK_NOGET for the ELO TS2700 touch screen USB HID device in
order to avoid a timeout during initialisation.
Signed-off-by: Mike Crowe <mac@mcrowe.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The infrared remote receiver found in the SantaRosa MacBookPro
laptops (MacBookPro3,1) need to be forced to expose a HIDDEV
interface (instead of HIDINPUT) so that lirc can access it using
the 'macmini' driver.
The patch below adds the required quirk for forcing the HIDDEV
interface to be activated (HID_QUIRK_HIDDEV) and introduces a new
quirk which forces the HIDINPUT interface to be ignored
(HID_QUIRK_IGNORE_HIDINPUT).
Note that Apple calls this receiver 'IRController4' (info taken
from Apple's driver Info.plist). Older Mac{Book,Mini,Pro}s seem
to all use the 'IRController1' device (USB id 05ac:8240) which
doesn't need those quirks.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a separate driver cm109 for handling this device.
Signed-off-by: Alfred E. Heggestad <aeh@db.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rework thrustmaster force-feedback module to support devices having
different types of force feedback effects. Add signatures of
Thrustmaster FGT Rumble Force and Thrustmaster FGT Force Feedback
wheels to the list of devices dupported by the module.
Parts of the patch were lifted off a simalar patch by
Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Autosuspend for USB HID devices remains problematic as far as mice
and keyboards are concerned. While I am working on a grand solution,
here's a minimalist patch that works for those devices not continously
in use.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If, in usb_hid_configure(), we fail to allocate storage for 'usbhid',
"if (!(usbhid = kzalloc(sizeof(struct usbhid_device), GFP_KERNEL)))",
then we'll jump to the 'fail:' label where we have this code:
usb_free_urb(usbhid->urbin);
usb_free_urb(usbhid->urbout);
usb_free_urb(usbhid->urbctrl);
Since we got here because we couldn't allocate storage for 'usbhid',
what we have here is a NULL pointer dereference - ouch...
This patch solves that little problem by adding a new
'fail_no_usbhid:' label after the problematic calls to
usb_free_urb() and jumps to that one instead, in the problem case.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some of ASUS' notebooks (e.g G Series) include a tiny oled display, which is
attached to an internal USB bus. Unfortunatly the device reports a wrong
DeviceDescriptor and is therefore identified as a HID device...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds the entire range of Logitech's ProductIDs that are reserved
for their Harmony remotes. The in-kernel HID driver can't do anything with
these, and now there is a GPL user-space application that can handle them:
http://www.sf.net/projects/harmonycontrol
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The IR sensor in some newer Apple computers has no other
driver in the kernel, yet. However, the macmini driver in lirc
requires a HID device for the IR sensor.
Cc: Soeren Sonnenburg <kernel@nn7.de>
Signed-off-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as918) introduces a new USB driver method: reset_resume.
It is called when a device needs to be reset as part of a resume
procedure (whether because of a device quirk or because of the
USB-Persist facility), thereby taking over a role formerly assigned to
the post_reset method. As a consequence, post_reset no longer needs
an argument indicating whether it is being called as part of a
reset-resume. This separation of functions makes the code clearer.
In addition, the pre_reset and post_reset method return types are
changed; they now must return an error code. The return value is
unused at present, but at some later time we may unbind drivers and
re-probe if they encounter an error during reset handling.
The existing pre_reset and post_reset methods in the usbhid,
usb-storage, and hub drivers are updated to match the new
requirements. For usbhid the post_reset routine is also used for
reset_resume (duplicate method pointers); for the other drivers a new
reset_resume routine is added. The change to hub.c looks bigger than
it really is, because mark_children_for_reset_resume() gets moved down
next to the new hub_reset_resume() routine.
A minor change to usb-storage makes the usb_stor_report_bus_reset()
routine acquire the host lock instead of requiring the caller to hold
it already.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as886) adds the controversial USB-persist facility,
allowing USB devices to persist across a power loss during system
suspend.
The facility is controlled by a new Kconfig option (with appropriate
warnings about the potential dangers); when the option is off the
behavior will remain the same as it is now. But when the option is
on, people will be able to use suspend-to-disk and keep their USB
filesystems intact -- something particularly valuable for small
machines where the root filesystem is on a USB device!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This keyboard has wireless mouse which has left, middle, right buttons and
2-dimensional scrolling wheel. Unfornetuly, this wheel reports side scrolling
events and 11 or 12 button events at the same time.
I've wrote a patch to fix this mapping. I'm not sure if this mapping is proper
for buttons, because , for example, there is no entry for "burn cd" in input.h.
The patch also supress 11 and 12 button events from mouse when you scroll the
wheel left and right. With this patch, only side scrolling events are
reported. (This mouse has only 4 buttons and 2D wheel. There is no such
buttons like 11 and 12.)
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When setting the autocentering of PID devices, PID_DIRECTION_ENABLE is not
being explicitely set to 1. This results in autocentering working only on the
vertical axis when this field is preset to 0.
Fix that by setting it explicitely to 1 when preparing the set_effect report
for autocentering spring effect.
Signed-off-by: Diogo Kastrup <dk@bighost.com.br>
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Lately there have been quite a lot of bug reports against broken devices
which require us to fix their report descriptor in the runtime, before it
is passed to the HID parser. Those devices have eaten quite an amount of
our quirks space, which isn't particularly necessary - the quirks are not
needed after the report descriptor is parsed, and they just consume bits.
Therefore this patch separates the quirks for report descriptor fixup, and
moves their handling into separate code. The quirks are then forgotten as
soon as the report descriptor has been parsed.
Module parameter 'rdesc_quirks' is introduced to be able to modify these
quirks in runtime in a similar way to 'quirks' parameter for ordinary HID
quirks.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Devices manufactured by NCR have userspace hiddev-based drivers,
which do all the necessary device querying by themselves. The devices
must not be queried directly by the generic HID driver, as reported by
NCR engineers.
Cc: Petr Ostadal <postadal@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Petalynx Maxter remote control [1] 0x18b1/0x0037 emits 0xfa and 0xfc from
consumer page (reserved in HUT 1.12) for back and more keys. It also emits
a few usages from LOGIVENDOR page, which need adding.
Also, this device has broken report descriptor - the reported maximum is too
low - it doesn't contain the range for 'back' and 'more' keys, so we need to
bump it up before the report descriptor is being parsed.
Besides all this, it also requires NOGET quirk.
This patch does so.
[1] http://www.elmak.pl/index.php?option=com_phpshop&page=shop.browse&category_id=14&ext=opis&lang=en
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch provides support for the Gameron dual psx adaptor. The
modification is to add the quirk HID_QUIRK_MULTI_INPUT for this
specific USB device.
Signed-off-by: Julien Eyries <jeyries@yahoo.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as914) replaces a call to flush_scheduled_work() with
cancel_work_sync(), in order to help avoid potential deadlocks.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Microsoft SideWinder GameVoice driver is a trivial device with a few buttons
(0x09 HID usage) and an audio connector, which just forwards the audio input
into oridinary sound card present in the computer.
Despite this fact, the only interface of this device reports itself as a
Telephony/Headset type of HID device. This is apparently incorrect - the device
itself doesn't provide any audio/telephony functionality. This is achieved in
userland application which only needs to receive the button events from the HID
driver.
This patch establishes a new quirk which forces hid-input to claim a device it
will otherwise leave untouched.
Reported-by: Tomas Carnecky <tom@dbservice.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There have been many reports recently about broken HID devices, the
diagnosis of which required users to recompile their kernels in order
to be able to provide debugging output needed for coding a quirk for
a particular device.
This patch makes CONFIG_HID_DEBUG default y if !EMBEDDED and makes it
possible to control debugging output produced by HID code by supplying
'debug=1' module parameter.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a small race window in which hiddev_release() could corrupt the
list that is being processed for new event in hiddev_send_event().
Synchronize the operations over this list.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In preparation for struct class_device -> struct device input
core conversion switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Logitech wheel (product id 0xc294) doesn't like to be polled for reports,
otherwise it slows down initialization of this device to ten seconds.
This patch adds HID_QUIRK_NOGET flag for this wheel.
Signed-off-by: Jan Kratochvil <honza@jikos.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Certain versions of Cypress USB barcode readers (this problem is known to
happen at least with PIDs 0xde61 and 0xde64) have report descriptor which
has swapped usage min and usage max tag. This results in HID parser failing
for report descriptor of these devices, as it (wrongly) requires allocating
more usages than HID_MAX_USAGES.
Solve this by walking through the report descriptor for such devices, and swap
the usage min and usage max items (and their values) to be in proper order.
Reported-by: Bret Towe <magnade@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It turns out that there are broken devices out there that incorrectly
report VID/PID as 0x000, see http://lkml.org/lkml/2007/4/27/496
Therefore we should not confuse users by dumping warnings and stacktraces
in such situation. It is not possible to add quirks for such horribly
broken devices, but currently that's not needed.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a 'quirks' module parameter for the usbhid module, so users can
add or modify quirks at module load time.
Signed-off-by: Paul Walmsley <paul@booyaka.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add internal support for dynamically-allocated HID quirks, "dquirks"
(for "dynamic quirks"). Includes several functions to add/modify quirks
from the list. This code is used by the next patch to implement quirk
modification upon module load.
Signed-off-by: Paul Walmsley <paul@booyaka.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rename existing quirks handling code that operates over a static array
to "squirks" (short for static quirks) to differentiate it from the
dynamically-allocated quirks that will be introduced in the
next patch. Add an accessor function specifically for static quirks,
usbhid_exists_squirk().
Signed-off-by: Paul Walmsley <paul@booyaka.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move the USB_VENDOR* and USB_DEVICE* defines and the hid_blacklist[]
array there from hid-core.c. Add
hid-quirks.c:usbhid_lookup_any_quirks() to return quirk information to
hid-core.c. Convert __u32, __u16 types to u32, u16.
Signed-off-by: Paul Walmsley <paul@booyaka.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add HID_QUIRK_MULTI_INPUT to the EMS USBII (0x0b43/0003) so the kernel detects both joystick
ports properly. Without it you end up with a single joystick node (js0) that combines the
two physical port signals.
Signed-off-by: Paul Zaremba <pez-gpg@treeofice.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds support for WiseGroup Quad Joypad (0x0925/0x8800). The
same quirks as for Dual Joypad (0x0925/0x8866) are needed.
Signed-off-by: Sam Liddicott <sam@liddicott.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for Logitech Force 3D Pro Joystick (0x046d/0xc286)
to hid-lgff driver.
Device ID reported by Richard Bolkey <rbolkey@cs.utexas.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On Dell W7658 keyboard, when BIOS sets NumLock LED on, it survives the
takeover by kernel and thus confuses users.
Eating of an increasibly scarce quirk bit is unfortunate. We do it for safety,
given the history of nervous input devices which crash if anything unusual
happens.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Logitech MX3000 contains report descriptor which doesn't cover usages
above 0x28c, but emits such usages. Report descriptor needs fixing
in the very same way as with receivers shipped with S510 keyboards.
This patch also adds a few mappings for multimedia keys that S510 didn't
emit.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Logitech S510 keyboard is shipped with USB receivers with various product
ids, all need their report descriptor to be fixed. This adds PID 0xc50c.
Reported by Christophe Colombier in kernel.org bugzilla #7352
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add HID_QUIRK_HIDDEV for the Belkin Flip USB KVM, which provides for software
control of switching via a HID class interface. It overloads three HID LED
usages, two of which aren't mapped in the ev_dev input subsection, and which it
doesn't make sense to map. In order to force the creation of a hiddev device
for controlling the Flip, this quirk flag is needed.
Signed-off-by: Daniel P. Engel <dengel@sourceharvest.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for version 1 of Thustmaster firestorm dual power
(0x44f/0xb300).
Signed-off-by: Ronny Peine <RonnyPeine@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Explicitly specify the size of the hid_blacklist quirks member, to guard
against surprises on architectures where unsigned ints aren't 32 bits long.
Signed-off-by: Paul Walmsley <paul@booyaka.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The USB HID driver fails to reset its error-retry timeout when there
has been a long time interval between I/O errors with no successful URB
completions in the meantime. As a result, the very next error would
trigger an immediate reset, even if it was a chance event occurring
long after the previous error.
More USB keyboards and mice than one might expect end up getting I/O
errors. Almost always this results from hardware problems of one sort of
another. For example, people attach the device to a USB extension cable,
which degrades the signal. Or they simply have poor quality cables to
begin with. Or they use a KVM switch which doesn't handle USB messages
correctly. Etc...
There have been reports from several users in which these I/O
errors would occur more or less randomly, at intervals ranging from
seconds to minutes. The error-handling code in hid-core.c was originally
meant for situations where a single outage would persist for a few hundred
ms (electromagnetic interference, for example). It didn't work right when
these more sporadic errors occurred, because of a flaw in the logic
which this patch fixes.
This patch (as873) fixes that oversight.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The vendor/product IDs for the purposes of hid_blacklist got
scathered around the hid-core.c in a rather random way over the
time.
Move all the related definitions at the beginning of the file,
and make them sorted again. Sort also hid_blacklist properly.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Separate usbhid code into dedicated drivers/hid/usbhid directory as
discussed previously with Greg, so that it eases maintaineance process.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jiri Kosina