OMAP4 has two mux instances, and the board may not have settings
for one of them. Allow the board file to pass NULL for an
instance's mux settings, which will initialize the mux instance
but skip writing board settings.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix below compilation warnings.
arch/arm/mach-omap2/omap_hwmod.c: In function 'omap_hwmod_for_each':
arch/arm/mach-omap2/omap_hwmod.c:1631: warning: 'ret' may be used uninitialized in this function
arch/arm/mach-omap2/mux.c: In function 'omap_mux_get_gpio':
arch/arm/mach-omap2/mux.c:917: warning: 'm' may be used uninitialized in this function
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently OMAP_DEVICE_PAD_IDLE flag is used to mux pins
dynamically. This can be simplified by using the enabled
state variable of each pad. This also fixes the issue of
the static pads not getting muxed after idling and
disable/enable state transitions.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This avoids going through the list unnecessarily when
idling devices for runtime PM.
Based on an earlier patch by sricharan <r.sricharan@ti.com>.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Do not create mux debugfs files as world-writable.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 8419fdbaf2
(omap2+: Add omap_mux_get_by_name) introduced the following
compile warning:
arch/arm/mach-omap2/mux.c: In function '_omap_mux_get_by_name':
arch/arm/mach-omap2/mux.c:163:17: warning: 'found_mode' may be used
uninitialized in this function
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
memcpy() copies 8 bytes too much (omap_mux_entry vs. omap_mux). Correct
by replacing memcpy() with struct assignment, which is safer.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow hwmod state changes to mux pads based on the state changes.
By default, only enable and disable the pads. In some rare cases
dynamic remuxing for the idles states is needed, this can be done
by passing the enable, idle, and off pads from board-*.c file along
with OMAP_DEVICE_PAD_REMUX flag.
Thanks to Paul Walmsley <paul@booyaka.com> for the comments on the
hwmod related changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows adding hwmod specific pads dynamically during the
platform device init.
Note that we don't currently have the hwmod specific signals
listed in the hwmod data, but struct omap_hwmod_mux_info will
make that possible if necessary.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Do this by splitting _omap_mux_init_signal as it already has most
of the necessary features.
Based on an earlier patch by Dan Murphy <dmurphy@ti.com>.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Removed mux: and added the __func__ macro to make debugging
easier.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Starting on OMAP4, the pin mux configuration is located in two
different partitions of the control module (CODE_PAD and WKUP_PAD).
The first one is inside the core power domain whereas the second
one is inside the wakeup.
- Add the capability to add any number of partition during board init
time depending of Soc partitioning.
- Add some init flags as well in order to avoid explicit Soc version
check inside the mux core code.
- Add a comment with mux0 mode on top of omap_mux/board/<partition>
if the current mux mode is not the default one.
Thanks to Tony Lindgren <tony@atomide.com> for the following improvements:
- Add omap_mux_get for getting the partition data so platform level
device code can use it.
- Fix the rx51 board code to use the new API.
- Do not store the partition for each mux entry. Look up the partition
for debugfs instead.
Thanks to Dan Murphy <dmurphy@ti.com> for testing on OMAP4 and reporting
a couple of bugs.
Thanks to Anand Gadiyar <gadiyar@ti.com> for testing on OMAP3 zoom and
bug report.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Murphy Dan <dmurphy@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Replace all the printk(KERN_XXX... with pr_xxx macros.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap. This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.
In response, move the SCM headers into mach-omap2/.
As part of this, remove the direct SCM access from the OMAP UDC
driver. It was clearly broken. The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
This patch fixes these compiler warnings:
CC arch/arm/mach-omap2/mux.o
arch/arm/mach-omap2/mux.c: In function 'omap_mux_init_gpio':
arch/arm/mach-omap2/mux.c:90: warning: 'gpio_mux' may be used uninitial
ized in this function
CC arch/arm/plat-omap/gpio.o
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_resume_after_idle':
arch/arm/plat-omap/gpio.c:2152: warning: 'l' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_prepare_for_idle':
arch/arm/plat-omap/gpio.c:2085: warning: 'l2' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c:2085: warning: 'l1' may be used uninitialized
in this function
CC arch/arm/mach-omap2/board-omap4panda.o
arch/arm/mach-omap2/board-omap4panda.c: In function 'omap4_panda_init':
arch/arm/mach-omap2/board-omap4panda.c:277: warning: unused variable 's
tatus'
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3530 CBB package can have GPIO126 muxed on 2 pins: mmc1_dat4 and
cam_strobe. This causes a problem with current multipath GPIO mux
handling, which muxes both pins as GPIO126 and makes the GPIO unusable.
Fix this by not muxing any pins if multipath GPIO is detected and
just print a warning instead. It's up to board files to set correct
mux using omap_mux_init_signal and pin name.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like 24xx uses mode3 instead of mode4 for muxable GPIO pins.
This will be needed when 24xx mux code is converted to use the new
mux functions.
Signed-off-by: Tony Lindgren <tony@atomide.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The check for a valid mux name should be performed regardless of whether
DEBUG_FS is enabled or not. Otherwise without DEBUG_FS, we get:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
last sysfs file:
Modules linked in:
CPU: 0 Not tainted (2.6.33-rc8 #10)
PC is at strcmp+0x18/0x40
LR is at omap_mux_init_signal+0x68/0x14c
...
This fixes the issue currently seen with boards not booting up
if DEBUG_FS is not enabled in defconfig.
Note that the earlier ifndef + ifdef now becomes simpler ifdef else:
If CONFIG_OMAP_MUX is selected, we use pin names. If it's not selected,
we only want the GPIO to mux register mapping.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Get rid of the ifdeffery in omap_mux_init by creating
omap_mux_init_package and omap_mux_init_signals functions.
Signed-off-by: Tony Lindgren <tony@atomide.com>
David Binderman ran the sourceforge tool cppcheck over the source code of the
new Linux kernel 2.6.33-rc6:
[./arm/mach-omap2/mux.c:492]: (error) Buffer access out-of-bounds
13 characters + 1 digit + 1 zero byte is more than 14 characters.
Also add a comment on mode0 name length in case new omaps
start using longer names.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
3630 has more mux signals than 34xx. The additional pins
exist in omap36xx_cbp_subset, but are not initialized
as the superset is missing these offsets. This causes
the following errors during the boot:
mux: Unknown entry offset 0x236
mux: Unknown entry offset 0x22e
mux: Unknown entry offset 0x1ec
mux: Unknown entry offset 0x1ee
mux: Unknown entry offset 0x1f4
mux: Unknown entry offset 0x1f6
mux: Unknown entry offset 0x1f8
mux: Unknown entry offset 0x1fa
mux: Unknown entry offset 0x1fc
mux: Unknown entry offset 0x22a
mux: Unknown entry offset 0x226
mux: Unknown entry offset 0x230
mux: Unknown entry offset 0x22c
mux: Unknown entry offset 0x228
Fix this by adding the missing offsets to omap3 superset.
Note that additionally the uninitialized pins need to be
skipped on 34xx.
Based on an earlier patch by Allen Pais <allen.pais@ti.com>.
Reported-by: Allen Pais <allen.pais@ti.com>
Signed-off-by: Allen Pais <allen.pais@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make the omap_mux_read and write available for board code,
and rename omap_mux_set_board_signals into omap_mux_write_array.
Also add the related prototypes and comments into mux.h.
In some cases we want to change the signals dynamically,
mostly for power management.
Note that we cannot use the signal names as they are set
__init to save memory.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like cmdline muxing got broken at some point when we
decided to limit muxing to __init code. Currently omap_mux_entry
list is not yet initialized when we try to initialize cmdline
muxing.
Fix this by calling omap_mux_init_list() before calling
omap_mux_set_cmdline_signals().
Reported-by: Philip Balister <philip@balister.org>
Tested-by: Philip Balister <philip@balister.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise bringing up new boards can be harder:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
last sysfs file:
Modules linked in:
CPU: 0 Not tainted (2.6.33-rc2-00015-g0bc9c93-dirty #37)
PC is at omap_mux_init+0xa4/0x3d8
LR is at omap_mux_init+0x3c/0x3d8
...
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initially only for 34xx. This code allows us to:
- Make the code more generic as the omap internal signal
names can stay the same across omap generations for some
devices
- Map mux registers to GPIO registers that is needed for
dynamic muxing of pins during off-idle
- Override bootloader mux values via kernel cmdline using
omap_mux=some.signa1=0x1234,some.signal2=0x1234
- View and set the mux registers via debugfs if
CONFIG_DEBUG_FS is enabled
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added runtime programming for the differences in EHCI interface between
OMAP3EVM revisions (Rev >= E) and (Rev < E).
Changes:
- EHCI PHY reset GPIO pin is 21 on Rev >= E while Rev < E
uses GPIO pin 135.
- Rev >= E uses EHCI Vbus enable GPIO22 line.
- Rev >= E uses GPIO61 to select EHCI port either on main board or
on Mistral Daughter Card (MDC). OMAP3EVM Rev < E doesn't have
EHCI port on main board.
- Currently GPIO61 it programmed to enable EHCI port on main
board only.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Earlier BeagleBoards were using pad AH8 muxed to GPIO29 for MMC write-protect.
However, this signal has been changed to pad AG9 in board revision C2.
Fix this by adding mux configuration for pad AG9, runtime check for board
revisions and set the gpio number and pad muxing accordingly.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO135 is used as EHCI (port2) phy reset pin on Multi Media Daughter card
connected to OMAP3EVM.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes for setting the padconf value for sys_nirq line
which is connected to T2 INTR1. This will fix the T2 keypad wakeup
issue on OMAP3 SDP.
Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For OMAP3 add MMC1 MMC2 pin mux MMC3 mux is not added as there are
multiple configurations possible, so the muxing is left to be done
in board file.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Chikkature Rajashekar <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patches ensures the MUX settings are correct for the SDRC
CKE signals to SDRAM. This allows the self-refresh to work when
2 chip-selects are in use.
A warning is thrown away in case the initial muxing is incorrect,
in order to track faulty or old-dated bootloaders.
Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options
must be enabled for the mux code to have effect.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds several new GPIO pins and updates
the pin naming comments.
The patch is based on earlier patches on linux-omap
list by Manikandan Pillai <mani.pillai@ti.com>,
Vaibhav Hiremath <hvaibhav@ti.com> and
David Brownell <dbrownell@users.sourceforge.net>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds some new pin multiplexing options
for McBSP and McSPI from Arun KS. Also add two more
GPIOs from David Brownell.
Also mark omap24xx_cfg_reg() static.
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal omap3430 support based on earlier patches from
Syed Mohammed Khasim. Also merge in omap34xx SRAM support
from Karthik Dasu and use consistent naming for sram init
functions.
Also do following changes that make 34xx support usable:
- Remove unused sram.c functions for 34xx
- Rename IRQ_SIR_IRQ to INTCPS_SIR_IRQ and define it locally
in entry-macro.S
- Update mach-omap2/io.c to support 2420, 2430, and 34xx
- Also merge in 34xx GPMC changes to add fields wr_access and
wr_data_mux_bus from Adrian Hunter
- Remove memory initialization call omap2_init_memory() until
until more generic memory initialization patches are posted.
It's OK to rely on bootloader initialization until then.
Signed-off-by: Syed Mohammed, Khasim <khasim@ti.com>
Signed-off-by: Karthik Dasu<karthik-dp@ti.com>
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds pinmux support for OMAP3. Incorporated review comments
from Tony to make mux_value as bit mask. Tested on 3430SDP.
Also merge in adding of I2C pins from Jarkko Nikula.
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Colin Cross