As usual, device tree updates is the bulk of our material in this merge
window. This time around, 559 patches affecting both 32- and 64-bit
platforms.
Changes are too many to list individually, but some of the larger ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also several
new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R45j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 Devicetree updates from Olof Johansson:
"As usual, device tree updates is the bulk of our material in this
merge window. This time around, 559 patches affecting both 32- and
64-bit platforms.
Changes are too many to list individually, but some of the larger
ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also
several new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board"
* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
ARM: dts: at91: at91sam9g45: add AC97
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
arm64: dts: uniphier: add PXs3 SoC support
ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
ARM: dts: uniphier: fix size of sdctrl nodes
ARM: dts: uniphier: add AIDET nodes
arm64: dts: uniphier: fix size of sdctrl node
arm64: dts: uniphier: add AIDET nodes
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
arm64: dts: uniphier: add reset controller node of analog amplifier
arm64: dts: marvell: add Device Tree files for Armada-8KP
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
...
Pretty much any node can have a status property, so it doesn't need to
be in examples.
Converted with the following command and removed examples with SoC and
board specific splits:
git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d'
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Correct misspelling, "emda3" -> "edma3".
Reported-by: Adam J Allison <adamj.allison@gmail.com>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change makes the DT file to be easier to read since the reserved slots
array does not need the '/bits/ 16' to be specified, which might confuse
some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This change makes the DT file to be easier to read since the memcpy
channels array does not need the '/bits/ 16' to be specified, which might
confuse some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
With the old binding and driver architecture we had many issues:
No way to assign eDMA channels to event queues, thus not able to tune the
system by moving specific DMA channels to low/high priority servicing. We
moved the cyclic channels to high priority within the code, but that was
just a workaround to this issue.
Memcopy was fundamentally broken: even if the driver scanned the DT/devices
in the booted system for direct DMA users (which is not effective when the
events are going through a crossbar) and created a map of 'used' channels,
this information was not really usable. Since via dmaengien API the eDMA
driver will be called with _some_ channel number, we would try to request
this channel when any channel is requested for memcpy. By luck we got
channel which is not used by any device most of the time so things worked,
but if a device would have been using the given channel, but not requested
it, the memcpy channel would have been waiting for HW event.
The old code had the am33xx/am43xx DMA event router handling embedded. This
should have been done in a separate driver since it is not part of the
actual eDMA IP.
There were no way to 'lock' PaRAM slots to be used by the DSP for example
when booting with DT.
In DT boot the edma node used more than one hwmod which is not a good
practice and the kernel prints warning because of this.
With the new bindings and the changes in the driver we can:
- No regression with Legacy binding and non DT boot
- DMA channels can be assigned to any TC (to set priority)
- PaRAM slots can be reserved for other cores to use
- Dynamic power management for CC and TCs, if only TC0 is used all other TC
can be powered down for example
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
information available within the IP instead
of reading it from platform data or DT. Some
other useful clean-ups are included too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=AWLc
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.16/edma' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
Merge "DaVinci EDMA clean-up for v3.16" from Sekhar Nori:
This series makes edma use configuration information available within
the IP instead of reading it from platform data or DT. Some other useful
clean-ups are included too.
* tag 'davinci-for-v3.16/edma' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci: (34 commits)
ARM: edma: Remove redundant/unused parameters from edma_soc_info
ARM: davinci: Remove redundant/unused parameters for edma
ARM: dts: am4372: Remove obsolete properties from edma node
ARM: dts: am33xx: Remove obsolete properties from edma node
dt/bindings: ti,edma: Remove redundant properties from documentation
ARM: edma: Get IP configuration from HW (number of channels, tc, etc)
ARM: edma: Save number of regions from pdata to struct edma
ARM: edma: Remove num_cc member from struct edma
ARM: edma: Remove queue_tc_mapping data from edma_soc_info
ARM: davinci: Remove eDMA3 queue_tc_mapping data from edma_soc_info
ARM: edma: Do not change TC -> Queue mapping, leave it to default.
ARM: edma: Take the number of tc from edma_soc_info (pdata)
ARM: edma: No need to clean the pdata in edma_of_parse_dt()
ARM: edma: Clean up and simplify the code around irq request
dmaengine: edma: update DMA memcpy to use new param element
dmaengine: edma: Document variables used for residue accounting
dmaengine: edma: Provide granular accounting
dmaengine: edma: Make reading the position of active channels work
dmaengine: edma: Store transfer data in edma_desc and edma_pset
dmaengine: edma: Create private pset struct
...
Signed-off-by: Olof Johansson <olof@lixom.net>
From CCCFG register of eDMA3 we can get all the needed information for the
driver about the IP:
Number of channels: NUM_DMACH
Number of regions: NUM_REGN
Number of slots (PaRAM sets): NUM_PAENTRY
Number of TC/EQ: NUM_EVQUE
The ti,edma-regions; ti,edma-slots and dma-channels in DT are
redundant since the very same information can be obtained from the HW.
The mentioned properties are deprecated.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This is another great example of trainwreck engineering:
commit 2646a0e529 (ARM: edma: Add EDMA crossbar event mux support)
added support for using EDMA on peripherals which have no direct EDMA
event mapping.
The code compiles and does not explode in your face, but that's it.
1) Reading an u16 array from an u32 device tree array simply does not
work. Even if the function is named "edma_of_read_u32_to_s16_array".
It merily calls of_property_read_u16_array. So the resulting 16bit
array will have every other entry = 0.
2) The DT entry for the xbar registers related to xbar has length 0x10
instead of the real length: 0xfd0 - 0xf90 = 0x40.
Not a real problem as it does not cross a page boundary, but
wrong nevertheless.
3) But none of this matters as the mapping never happens:
After reading nonsense edma_of_read_u32_to_s16_array() invalidates
the first array entry pair, so nobody can ever notice the
braindamage by immediate explosion.
Seems the QA criteria for this code was solely not to explode when
someone adds edma-xbar-event-map entries to the DT. Goal achieved,
congratulations!
Not really helpful if someone wants to use edma on a device which
requires a xbar mapping.
Fix the issues by:
- annotating the device tree entry with "/bits/ 16" as documented in
the of_property_read_u16_array kernel doc
- make the size of the xbar register mapping correct
- invalidating the end of the array and not the start
This convoluted mess wants to be completely rewritten as there is no
point to keep the xbar_chan array memory and the iomapping of the xbar
regs around forever. Marking the xbar mapped channels as used should
be done right there.
But that's a different issue and this patch is small enough to make it
work and allows a simple backport for stable.
Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The binding definition is based on the generic DMA controller
binding.
Joel:
* Droped reserved and queue DT entries from Documentation
for now from the original patch series (v10)
* Included properties in Documentation and clarified DMA properties (V11)
* Made ti,hwmod option
* Clarified DMA entries
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Linus Torvalds