The current driver receive path allocates pages and stashes
them into SKB fragments. This is not particularly useful as
we don't support jumbo frames (which wouldn't be great with
the small FIFOs on all the known implementations) anyway.
It also makes us flush the caches and allocate more memory
for RX than necessary.
So set our RX buf to our max packet size instead (which we
bump to 1536 bytes to account for packets with vlan tags
etc...) like most other ethernet drivers.
Then allocate skbs when populating the receive ring and DMA
directly into them.
This simplifies the RX path further.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't handle fragmented RX packets, so the "looping"
helpers to locate the first segment of a packet or to
drop a packet aren't actually helping.
Take them out and simplify ftgmac100_rx_packet() further
as a result.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fast path has a single unlikely() test for any error bit,
calling into a helper that sets the appropriate statistics.
The various netdev_info aren't particularly interesting. If
we want to differentiate the various length errors later we
can introduce driver specific stats using ethtool.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the descriptor field only once and check for IP header
checksum errors as well
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can occasionally fail to allocate new RX buffers at
runtime or when starting the driver. At the moment the
latter just fails to open which is fine but the former
leaves stale DMA pointers in the ring.
Instead, use a scratch page and have all RX ring descriptors
point to it by default unless a proper buffer can be allocated.
It will help later on when re-initializing the whole ring
at runtime on link changes since there is no clean failure
path there unlike open().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't support jumbo frames, we will never receive a
fragmented packet, the RX buffer is always big enough,
if not then it's a runaway packet that can be dropped.
So take out the loop that handles such things in
ftgmac100_rx_packet() which will help with subsequent
simplifications and improvements to the RX path
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
First, don't look at the interrupt status in the poll loop
to decide what to poll. It's wrong. If we have run out of
budget, we may still have RX packets to unqueue but no more
RX interrupt pending.
So instead move the code looking at the interrupt status
into the interrupt handler where it belongs. That avoids a slow
MMIO read in the NAPI fast path. We keep the abnormal interrupts
enabled while NAPI is scheduled.
While at it, actually do something useful in the "error" cases:
On AHB bus error, trigger the new reset task, that's about all
we can do. On RX packet fifo or descriptor overflows, we need
to restart the MAC after having freed things up. So set a flag
that NAPI will see and use to perform that restart after
harvesting the RX ring.
Finally, we shouldn't complete NAPI if there are still outgoing
packets that will need harvesting. Waiting for more interrupts
is less efficient than letting NAPI run a while longer while
the queue drains.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt is neither enabled nor registered when the interface
isn't running (regardless of whether we use nc-si or not) so the
test isn't useful.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HW requires a full MAC reset when changing the speed.
Additionally the Aspeed documentation spells out that the
MAC needs to be reset twice with a 10us interval.
We thus move the speed setting and top level reset code
into a new ftgmac100_reset_and_config_mac() function which
handles both. Move the ring pointers initialization there
too in order to reflect the HW change.
Also reduce the timeout for the MAC reset as it shouldn't
take more than 300 clock cycles according to the doc.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link speed changes require a full HW reset. This isn't done
properly at the moment. It will involve delays and thus isn't
suitable to do from the link poll callback.
So let's create a reset_task that we can queue up when the
link changes. It will be useful for various cases of error
handling as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link monitoring and error handling code will have to
redo the ring inits and HW setup so move the code out of
ftgmac100_open() into a dedicated function.
This forces a bit of re-ordering of ftgmac100_open() but
nothing dramatic.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt isn't shared, so this will keep it masked
until we have the HW in a known sane state.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a single function is used to allocate the rings
themselves, initialize them, populate the rx ring, and
allocate the rx buffers. The same happens on free.
This splits them into separate functions. This will be
useful when properly implementing re-initialization on
link changes and error handling when the rings will be
repopulated but not freed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep track of both the current speed and duplex settings
instead of only speed and properly apply the duplex setting
to the HW.
This reworks the adjust_link() function to also avoid trying
to reconfigure the HW when there is no link and to display
the link state to the user.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not used in any meaningful way
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorder the fields in struct ftgmac in slightly more logical
groups. Will make more sense as I add/remove some.
No code change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The divisions they represent are not particularily meaningful
and things are going to be moving around with upcoming changes
making these comments more a burden than anything else.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a placeholder already for the irq, use it
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver uses interfaces from linux/of.h and linux/property.h but
relies on implict inclusion of those headers which means that changes in
other headers could break the build, as happened in -next for arm today.
Add a explicit includes.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if bus is not hot-pluggable, devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This stops NCSI device when closing the network device so that the
NCSI device can be reenabled later.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHYSTS_CHG (the ftgmac100's PHY IRQ) is telling the system to go
look at the PHY registers for a link status change.
The interrupt was causing issues on Aspeed SoC where some board designs
had an active high configuration, some active low, and in some cases
repurposed for other functions. When misconfigured Linux would chew 100%
of CPU cycles servicing interrupts:
[ 20.280000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG
[ 20.280000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG
[ 20.280000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG
[ 20.300000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG
While in the ftgmac100 IP can be configured for high, low and edge
sensitivity the current driver always polls the PHY, so we chose to mask
out the interrupt.
See https://patchwork.ozlabs.org/patch/672099/ for more discussion.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Aspeed SoCs have a new MDIO interface as an option in the G4 and G5
SoCs. The old one is still available, so select it in order to remain
compatible with the ftgmac100 driver.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is stale interrupt (PHYSTS_CHG in ISR, bit#6 in 0x0) from
the bootloader (uboot) when enabling the MAC. The stale interrupts
aren't part of kernel and should be cleared.
This clears the stale interrupts in ISR (0x0) when enabling the MAC.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RXDES and TXDES registers bits in the ftgmac100 indicates EDO{R,T}R
at bit position 15 for the Faraday Tech IP. However, the version of this
IP present in the Aspeed SoCs has these bits at position 30 in the
registers.
It appers that ast2400 SoCs support both positions, with the 15th bit
marked as reserved but still functional. In the ast2500 this bit is
reused for another function, so we need a work around.
This was confirmed with engineers from Aspeed that using bit 30 is
correct for both the ast2400 and ast2500 SoCs.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
These bits are #defined at a fixed location. In order to support future
hardware that has chosen to move these bits around move the bits into a
member of the struct ftgmac100.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ftgmac100 hardware revision in e.g. the Aspeed AST2500 no longer
reserves all bits in RXDES#2 but instead uses the bottom 16 bits to
store MAC frame metadata. Avoid corruption by shifting struct page
pointers out to their own member in struct ftgmac100.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initial MAC address is retrieved from hardware if it's not
provided by device-tree. The reserved MAC address from hardware
will be used if non-reserved MAC address is invalid. It will
cause mismatched MAC address seen by hardware and software.
This disallows using the reserved hardware MAC address to avoid
the mismatched MAC address seen by hardware and software.
Fixes: 113ce107af ("net/faraday: Read MAC address from chip")
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bogus PHY interrupts are observed. This masks the PHY interrupt
when the interface works in NCSI mode as there is no attached
PHY under the circumstance.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This matches the driver with devices compatible with "faraday,ftgmac100"
declared in the device tree. Originally, device's name from device
tree for it.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes ftgmac100 driver support NCSI mode. The NCSI is enabled
on the interface if property "use-nc-si" or "use-ncsi" is found from
the device node in device tree.
* No PHY device is used when NCSI mode is enabled.
* The NCSI device (struct ncsi_dev) is created when probing the
device while it's enabled/started when the interface is brought
up.
* Hardware IP checksum dosn't work when NCSI mode is enabled. It
is disabled on enabled NCSI.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device is assigned with random MAC address. It isn't reasonable.
An valid MAC address might have been provided by (uboot) firmware by
device-tree or in chip. It's reasonable to use it to maintain consistency.
This uses the MAC address from device-tree or that in the chip if it's
valid. Otherwise, a random MAC address is given as before.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces two helper functions to create or destroy MDIO
interface. No logical changes introduced except the proper MDIO
names are given when having more than one MDIO bus.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_find_first() to find the first phy device instead of
open coding it.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ftgmac100_mdiobus_reset() does nothing useful and is optional for the
MDIO bus code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to get correct drop monitor notifications for dropped
packets, we should call kfree_skb() instead of dev_kfree_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__GFP_ZERO is an uncommon flag and perhaps is better
not used. static inline dma_zalloc_coherent exists
so convert the uses of dma_alloc_coherent with __GFP_ZERO
to the more common kernel style with zalloc.
Remove memset from the static inline dma_zalloc_coherent
and add just one use of __GFP_ZERO instead.
Trivially reduces the size of the existing uses of
dma_zalloc_coherent.
Realign arguments as appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_platform_driver macro removes some boilerplate and makes
the code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the number of calls required to alloc
a zeroed block of memory.
Trivially reduces overall object size.
Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should pull only ethernet header from page frag
to skb->head.
Pulling 64 bytes is too much for TCP (without options) on IPv4.
However, it makes sense to pull all the frame if it fits the
128 bytes bloc allocated for skb->head, to free one page per
small incoming frame.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Po-Yu Chuang <ratbert@faraday-tech.com>
Acked-by: Yan-Pai Chen <yanpai.chen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace usage of random_ether_addr() with eth_hw_addr_random()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Change the trivial cases.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes compilation failure of these modules due to missing
irqreturn_t type for the ft(g)mac100_interrupt definition.
Signed-off-by: Thomas Faber <thfabba@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
ftgmac100 allocates a page per skb fragment. We must account
PAGE_SIZE increments on skb->truesize, not the actual frag length.
If frame is under 64 bytes, page is freed, and truesize adjusted.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Faraday driver into drivers/net/ethernet/faraday/ and
make the necessary Kconfig and Makefile changes.
CC: "Po-Yu Chuang" <ratbert@faraday-tech.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Benjamin Herrenschmidt