The drivers current default configuration drives the pixel data
on rising edge of the pixel clock. However, most display sample
data on rising edge... This leads to color shift artefacts visible
especially at edges.
This patch changes the relevant defines to be useful and actually
set the bits, and changes pixel clock polarity to drive the pixel
data on falling edge by default. The patch also adds an explicit
pixel clock polarity flag to the display introduced with the driver
(NEC WQVGA "nec,nl4827hc19-05b") using the new bus_flags field to
retain the initial behavior.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Use the common clock framework to calculate the pixel clock
dividier. The previous implementation rounded down the calculated
factor. Thanks to the CLK_DIVIDER_ROUND_CLOSEST flag using the
common clock framework divider implementation improves the pixel
clock accuracy in some cases. Ontop of that it also allows to see
the actual pixel clock in the sysfs clock summary.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The Vybrid DCU variant has two independent clock inputs, one
for the registers (IPG bus clock) and one for the pixel clock.
Support this distinction in the DCU DRM driver while staying
backward compatible for old device trees.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
The layer enumeration start with 0 (0-15 for LS1021a and 0-63 for
Vybrid) whereas the register enumeration start from 1 (1-10 for
LS1021a and 1-9 for Vybrid). The loop started off from 0 for both
iterations and initialized the number of layers inclusive, which
is one layer too many.
All extensively written registers seem to be unassigned, it seems
that the write to those registers did not do any harm in practice.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The current default configuration is as follows:
- Invert VSYNC signal (active LOW)
- Invert HSYNC signal (active LOW)
The mode flags allow to specify the required polarity per
mode. Furthermore, none of the current driver settings is
actually a standard polarity.
This patch applies the current driver default polarities as
explicit flags to the display which has been introduced with
the driver (NEC WQVGA "nec,nl4827hc19-05b"). The driver now
also parses the flags field and applies the configuration
accordingly, by using the following values as standard
polarities: (e.g. when no flags are specified):
- VSYNC signal not inverted (active HIGH)
- HSYNC signal not inverted (active HIGH)
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Improve error handling during CRTC initialization. Especially avoid
memory leaks in the primary plane initialization error path.
Signed-off-by: Stefan Agner <stefan@agner.ch>
It is not common to do regmap return value checks, especially not
for memory mapped device. We can rule out most error returns since
the conditions are static and we know they are ok (e.g. offset
aligned to register stride). Also without proper error handling
they are not really valuable for the user. Hence remove most of
them.
The check in the interrupt handler is worth keeping since a
volatile register won't be readable in case register caching is
still enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
I didn't convert drm_crtc_init() since passing the varargs through
would mean either cpp macros or va_list, and I figured we don't
care about these legacy functions enough to warrant the extra pain.
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4, E5;
@@
drm_crtc_init_with_planes(E1, E2, E3, E4, E5
+ ,NULL
)
v2: Split crtc and plane changes apart
Pass NULL for no-name instead of ""
Leave drm_crtc_init() alone
v3: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670771-2751-1-git-send-email-ville.syrjala@linux.intel.com
This patch add support for Two Dimensional Animation and Compositing
Engine (2D-ACE) on the Freescale SoCs.
2D-ACE is a Freescale display controller. 2D-ACE describes
the functionality of the module extremely well its name is a value
that cannot be used as a token in programming languages.
Instead the valid token "DCU" is used to tag the register names and
function names.
The Display Controller Unit (DCU) module is a system master that
fetches graphics stored in internal or external memory and displays
them on a TFT LCD panel. A wide range of panel sizes is supported
and the timing of the interface signals is highly configurable.
Graphics are read directly from memory and then blended in real-time,
which allows for dynamic content creation with minimal CPU
intervention.
The features:
(1) Full RGB888 output to TFT LCD panel.
(2) Blending of each pixel using up to 4 source layers
dependent
on size of panel.
(3) Each graphic layer can be placed with one pixel resolution
in either axis.
(4) Each graphic layer support RGB565 and RGB888 direct colors
without alpha channel and BGRA8888 BGRA4444 ARGB1555 direct
colors
with an alpha channel and YUV422 format.
(5) Each graphic layer support alpha blending with 8-bit
resolution.
This is a simplified version, only one primary plane, one
framebuffer, one crtc, one connector and one encoder for TFT
LCD panel.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Stefan Agner