The imx7d-sdb has a mickro bus connector that can be connected to a
Sensirion SHT11 click board (temperature and humidity sensor):
https://shop.mikroe.com/click/sensors/sht1x
Add a new device tree file to describe such hardware.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PHYs embedded in the switch direct there interrupts through the
switch interrupt controllers. Now that devel C has its switch
interrupts connected to the SoC, the PHY interrupts can be used by
phylib. Explicitly include MDIO nodes in the switch device tree nodes,
and link the PHY interrupts back to the switch interrupt
controller. Also, link the ports to the PHYs on the MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The devel B and devel C board use the same GPIO lines for interrupts
from the two switches. Move the pinmux nodes from devel B into the
shared .dtsi file, and wire up the interrupts on devel C.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
UART on i.MX6SX (like all other i.MX6 SoC variants) has the same
programming model as the 'imx6q-uart' type, so add it to the compatible
UART string.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change the maxium spi clock frequency from 20MHz to 10MHz to meet the
operation voltage range requirement recommended in AT25 datasheet.
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the reference manuals, both imx50/imx53 SOC seem to share
the same eSDHC controller, especially the section on "Multi-block Read"
mentioned in commit 361b848202 ("mmc: sdhci-esdhc-imx: fix multiblock
reads on i.MX53") is identical for both SOC.
Hence, let imx50 use imx53-esdhc.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reference them by handle and remove the changed clocks that are copied
from the downstream DT and are not part of the mainline binding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Referencing the node by handle make the QP DT more resilent against
changes of the base DT. Also remove the duplicated reg property, it's
not needed as it the same as in the base DT, just the compatible is
actually different.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
By using the handle, we can avoid some duplication of the base DT
and so avoid any maintenance overhead in the QP DT if the referenced
node changes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All currently supported i.MX25-based machines use phy_type = "utmi" and
dr_mode = "otg". So this seems to be a sensible default.
This also doesn't hurt out-of-tree machines because up to now they had
to specify these two properties in the machine.dts which still takes
precedence by just overwriting the defaults added here.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This machine is based on I2SE's Duckbill 2 board and is sold as part
of I2SE's PLC Bundle for IoT. This is a development kit for Homeplug
Green PHY based powerline products based on Qualcomms QCA7000 chip.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This machine is based on I2SE's Duckbill 2 board and features a
EnOcean daugther board based on the popular TCM310 chipset.
This product is intended to be used for e.g. home automation purposes.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This machine is based on I2SE's Duckbill 2 board and features a
RS-485 daugther board. This device is intended to be used for
e.g. home automation purposes.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This machine is an USB pen drive sized development board,
based on NXP's i.MX28 CPU. In contrast to the previous
model "Duckbill", the "Duckbill 2" series has internal
eMMC storage.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch updates the Duckbill device tree and synchronize it with
the vendor distributed file. The changes in mostly pin-muxing stuff,
but also some minor fixes. In detail:
- enable SPI pins
- enable I2C pins
- enable UART pins
- enable LRADC pin
- adjust USB DR mode
- add default triggers for LEDs
- get rid of regulators simple-bus container
- adjust phy reset duration
According to phy datasheet, 25ms are sufficient. This also reduces
the time to boot the system.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch renames mmc2_sck_cfg in order to prepare for an alternative
muxing setup.
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Quoting Philipp Zabel:
"Since this regulator is used as the TVDAC analog power supply, this
range should at least be limited to the analog power supply range of the
TVDAC, listed in Table 74-9. of the i.MX53 reference manual (2.5-2.75V).
But since the nominal voltage is 2.75V, which was used to determine the
analog gain that is supposed to result in the necessary 0.7V
peak-to-peak amplitude on the VGA output, I'd say we should just fix the
voltage to 2750000 here."
, so limit the TVDAC analog power supply as suggested.
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cm-fx6 module has an onboard Wolfson wm8731 codec which is muxed
to the ssi2 controller. Unlike most (all?) supported i.MX6 board/codec
combinations the wm8731 is operated in slave mode and the clock setup
is static.
Add support for it.
Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
[christopher.spinrath@rwth-aachen.de: enhanced commit message, ported
to upstream and some cleanup]
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Leave pca953x P06,P07 pins on b850v3 platform and P06 pin on
b450v3/b650v3 unconfigured in the kernel space since they could be
configured as DP1_RST and DP2_RST by the applications for the DP FW
update support.
Signed-off-by: Ken Lin <ken.lin@advantech.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull crypto fixes from Herbert Xu:
- vmalloc stack regression in CCM
- Build problem in CRC32 on ARM
- Memory leak in cavium
- Missing Kconfig dependencies in atmel and mediatek
- XTS Regression on some platforms (s390 and ppc)
- Memory overrun in CCM test vector
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: vmx - Use skcipher for xts fallback
crypto: vmx - Use skcipher for cbc fallback
crypto: testmgr - Pad aes_ccm_enc_tv_template vector
crypto: arm/crc32 - add build time test for CRC instruction support
crypto: arm/crc32 - fix build error with outdated binutils
crypto: ccm - move cbcmac input off the stack
crypto: xts - Propagate NEED_FALLBACK bit
crypto: api - Add crypto_requires_off helper
crypto: atmel - CRYPTO_DEV_MEDIATEK should depend on HAS_DMA
crypto: atmel - CRYPTO_DEV_ATMEL_TDES and CRYPTO_DEV_ATMEL_SHA should depend on HAS_DMA
crypto: cavium - fix leak on curr if curr->head fails to be allocated
crypto: cavium - Fix couple of static checker errors
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
This includes two branches for arm64 dt updates, both following up
on earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the
start of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=A3U6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
This includes two branches for arm64 dt updates, both following up on
earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the start
of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: deconfig: fix the moxart defconfig
ARM: ux500: resume the second core properly
arm64: dts: juno: update definition for programmable replicator
arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost
arm64: dts: exynos: Add USB 3.0 controller node for Exynos7
arm64: dts: exynos: Use macros for pinctrl configuration on Exynos7
pinctrl: dt-bindings: samsung: Add Exynos7 specific pinctrl macro definitions
arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e
ARM64: dts: meson-gxbb-p200: add ADC laddered keys
ARM64: dts: meson: meson-gx: add the SAR ADC
ARM64: dts: meson-gxl: add the pwm_ao_b pin
ARM64: dts: meson-gx: add the missing pwm_AO_ab node
clk: gxbb: fix CLKID_ETH defined twice
ARM64: dts: meson-gxl: rename Nexbox A95x for consistency
clk: gxbb: add the SAR ADC clocks and expose them
dt-bindings: amlogic: Add WeTek boards
ARM64: dts: meson-gxbb: Add support for WeTek Hub and Play
dt-bindings: vendor-prefix: Add wetek vendor prefix
ARM64: dts: meson-gxm: Rename q200 and q201 DT files for consistency
ARM64: dts: meson-gx: Add HDMI HPD/DDC pinctrl nodes
...
task_struct::signal and task_struct::sighand are pointers, which would normally make it
straightforward to not define those types in sched.h.
That is not so, because the types are accompanied by a myriad of APIs (macros and inline
functions) that dereference them.
Split the types and the APIs out of sched.h and move them into a new header, <linux/sched/signal.h>.
With this change sched.h does not know about 'struct signal' and 'struct sighand' anymore,
trying to put accessors into sched.h as a test fails the following way:
./include/linux/sched.h: In function ‘test_signal_types’:
./include/linux/sched.h:2461:18: error: dereferencing pointer to incomplete type ‘struct signal_struct’
^
This reduces the size and complexity of sched.h significantly.
Update all headers and .c code that relied on getting the signal handling
functionality from <linux/sched.h> to include <linux/sched/signal.h>.
The list of affected files in the preparatory patch was partly generated by
grepping for the APIs, and partly by doing coverage build testing, both
all[yes|mod|def|no]config builds on 64-bit and 32-bit x86, and an array of
cross-architecture builds.
Nevertheless some (trivial) build breakage is still expected related to rare
Kconfig combinations and in-flight patches to various kernel code, but most
of it should be handled by this patch.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The moxart defconfig wasn't even building a kernel for Moxart,
it was building a kernel for V4T on the nothing platform. Switch
to MULTI_V4 and keep the right drivers, update a few selections.
Now it (presumably) builds a minimalist Moxart kernel again.
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The pen hold/release scheme was copied over to Ux500 from the ARM
reference designs like most of these at the time. It is not needed
at all, and was mostly removed in commit c00def71ef
"ARM: ux500: simplify secondary CPU boot".
However on the suspend/resume path and hot plug/unplug of CPUs,
the .cpu_die() callback was still waiting for the pen to be
released which made it spin forever and the second core never come
back online after suspend/resume.
Fix this by simply replacing the strange custom .cpu_die() with
a oneline wfi() just like e.g. the qcom platform does. This fixes
the issue and makes the second core come up properly after
suspend/resume.
As a side effect, this rids us of the completely surplus local
setup.h and hotplug.c files, and we just compile this into platsmp.c
with everything else SMP.
Cc: stable@vger.kernel.org
Fixes: c00def71ef ("ARM: ux500: simplify secondary CPU boot")
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Update code that relied on sched.h including various MM types for them.
This will allow us to remove the <linux/mm_types.h> include from <linux/sched.h>.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/task_stack.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task_stack.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/task.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/hotplug.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/hotplug.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/debug.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/debug.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add #include <linux/cred.h> dependencies to all .c files rely on sched.h
doing that for them.
Note that even if the count where we need to add extra headers seems high,
it's still a net win, because <linux/sched.h> is included in over
2,200 files ...
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split more MM APIs out of <linux/sched.h>, which
will have to be picked up from a couple of .c files.
The APIs that we are going to move are:
arch_pick_mmap_layout()
arch_get_unmapped_area()
arch_get_unmapped_area_topdown()
mm_update_next_owner()
Include the header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/mm.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/mm.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
The APIs that are going to be moved first are:
mm_alloc()
__mmdrop()
mmdrop()
mmdrop_async_fn()
mmdrop_async()
mmget_not_zero()
mmput()
mmput_async()
get_task_mm()
mm_access()
mm_release()
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to move scheduler ABI details to <uapi/linux/sched/types.h>,
which will be used from a number of .c files.
Create empty placeholder header that maps to <linux/types.h>.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/clock.h> out of <linux/sched.h>, which
will have to be picked up from other headers and .c files.
Create a trivial placeholder <linux/sched/clock.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/topology.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/topology.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The accelerated CRC32 module for ARM may use either the scalar CRC32
instructions, the NEON 64x64 to 128 bit polynomial multiplication
(vmull.p64) instruction, or both, depending on what the current CPU
supports.
However, this also requires support in binutils, and as it turns out,
versions of binutils exist that support the vmull.p64 instruction but
not the crc32 instructions.
So refactor the Makefile logic so that this module only gets built if
binutils has support for both.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Annotate a vmov instruction with an explicit element size of 32 bits.
This is inferred by recent toolchains, but apparently, older versions
need some help figuring this out.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull ARM updates from Russell King:
- nommu updates from Afzal Mohammed cleaning up the vectors support
- allow DMA memory "mapping" for nommu Benjamin Gaignard
- fixing a correctness issue with R_ARM_PREL31 relocations in the
module linker
- add strlen() prototype for the decompressor
- support for DEBUG_VIRTUAL from Florian Fainelli
- adjusting memory bounds after memory reservations have been
registered
- unipher cache handling updates from Masahiro Yamada
- initrd and Thumb Kconfig cleanups
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (23 commits)
ARM: mm: round the initrd reservation to page boundaries
ARM: mm: clean up initrd initialisation
ARM: mm: move initrd init code out of arm_memblock_init()
ARM: 8655/1: improve NOMMU definition of pgprot_*()
ARM: 8654/1: decompressor: add strlen prototype
ARM: 8652/1: cache-uniphier: clean up active way setup code
ARM: 8651/1: cache-uniphier: include <linux/errno.h> instead of <linux/types.h>
ARM: 8650/1: module: handle negative R_ARM_PREL31 addends correctly
ARM: 8649/2: nommu: remove Hivecs configuration is asm
ARM: 8648/2: nommu: display vectors base
ARM: 8647/2: nommu: dynamic exception base address setting
ARM: 8646/1: mmu: decouple VECTORS_BASE from Kconfig
ARM: 8644/1: Reduce "CPU: shutdown" message to debug level
ARM: 8641/1: treewide: Replace uses of virt_to_phys with __pa_symbol
ARM: 8640/1: Add support for CONFIG_DEBUG_VIRTUAL
ARM: 8639/1: Define KERNEL_START and KERNEL_END
ARM: 8638/1: mtd: lart: Rename partition defines to be prefixed with PART_
ARM: 8637/1: Adjust memory boundaries after reservations
ARM: 8636/1: Cleanup sanity_check_meminfo
ARM: add CPU_THUMB_CAPABLE to indicate possible Thumb support
...
Round the initrd memblock reservation to page boundaries to prevent
other data sharing the initrd pages. This prevents an allocation
possibly overlapping with the initrd, which would later get trampled
on in free_initrd_mem().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Rather than repeatedly testing phys_initrd_size to see if the initrd
is still enabled, return from the new function to avoid executing the
remaining initialisation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Move the ARM initrd initialisation code out of arm_memblock_init() into
its own function, so it can be cleaned up.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Peter Senna Tschudin