Add probe and disconnect callbacks that behaves similarly than ones
used commonly on Linux driver model. We need those to get early / late
access to driver in order to use normal probe time stuff, like regmap,
extra bus adapters and so.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace static stream settings by one which enables and disables
stream interface when needed (TS streaming control).
1) Configure both TS IF and USB endpoints according to current use case
2) Disable streaming USB endpoints when streaming is stopped and
enable when streaming is started. Reduces sleep power consumption
slightly.
3) Reduce USB buffersize slightly, from 130848 to 98136 bytes
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
PID filters are moved to af9013 demod driver as those are property of
demod. As pid filters are now implemented correctly by demod driver,
we could enable pid filter support for possible slave demod too on
dual tuner configuration.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
af9013 demod driver has i2c binding. Use it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pass correct device to dev_* logging functions, which allows us to
remove redundant KBUILD_MODNAME and __func__ parameters from log format.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop bogus call to usb_driver_release_interface() from the disconnect()
callback. As the interface is already being unbound at this point,
usb_driver_release_interface() simply returns early.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_subdev core s_power op was used for two different things: power on/off
sensors or video decoders/encoders and to put a tuner in standby (and only the
tuner!). There is no 'tuner wakeup' op, that's done automatically when the tuner
is accessed.
The danger with calling (s_power, 0) to put a tuner into standby is that it is
usually broadcast for all subdevs. So a video receiver subdev that supports
s_power will also be powered off, and since there is no corresponding (s_power, 1)
they will never be powered on again.
In addition, this is specifically meant for tuners only since they draw the most
current.
This patch adds a new tuner op called 'standby' and replaces all calls to
(core, s_power, 0) by (tuner, standby). This prevents confusion between the two
uses of s_power. Note that there is no overlap: bridge drivers either just want
to put the tuner into standby, or they deal with powering on/off sensors. Never
both.
This also makes it easier to replace s_power for the remaining bridge drivers
with some PM code later.
Whether we want something cleaner for tuners in the future is a separate topic.
There is a lot of legacy code surrounding tuners, and I am very hesitant about
making changes there.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is a double sizeof() typo here so we don't duplicate the struct
properly.
Fixes: be7fd3c3a8 ("media: em28xx: Hauppauge DualHD second tuner functionality")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Hauppauge HVR-975 is a hybrid, dual frontend, single tuner USB device.
It contains lgdt3306a and si2168 frontends and one si2157 tuner. The
lgdt3306a frontend is currently enabled. This creates the second
demodulator and attaches it to the tuner.
Enables lgdt3306a|si2168 + si2157
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If frontend[1] exists, then enable the dvb adapter mfe lock system.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Utilize the i2c mux adapter returned by the frontend.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On some architectures such as arm64, siano chip based TV-tuner
USB devices are not recognized correctly due to coherent memory
allocation failure with the following error:
[ 663.556135] usbcore: deregistering interface driver smsusb
[ 683.624809] smsusb:smsusb_probe: board id=18, interface number 0
[ 683.633530] smsusb:smsusb_init_device: smscore_register_device(...) failed, rc -12
[ 683.641501] smsusb:smsusb_probe: Device initialized with return code -12
[ 683.652978] smsusb: probe of 1-1:1.0 failed with error -12
This is caused by dma_alloc_coherent(NULL, ...) returning NULL in
smscoreapi.c.
To fix this error, allocate the buffer memory for the USB devices
via kmalloc() and let the USB core do the DMA mapping and free.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some local variables will be set to an appropriate value before usage.
Thus omit explicit initialisations at the beginning of these functions.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge Solo/Dual HD DVB models use a si2157 tuner, which is set to
produce inverted spectrum. This configures the si2168 DVB demod for
inverted spectrum on both affected models.
[mchehab@s-opensource.com: rebased on the top of upstream]
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Include ability to add a i2c device style frontend to cx231xx USB
bridge. All current boards set to use frontend[0]. Changes are
backwards compatible with current behaviour.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Include ability to add a second dvb attach style frontend to cx231xx
USB bridge. All current boards set to use frontend[0]. Changes are
backwards compatible with current behaviour.
[mchehab@s-opensource.com: fix some coding style issues]
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit f8585ce655 ("[media] dvb-usb-cxusb: Geniatech T230C support")
sneaked in an unrelated change for the older T230 (not C) model.
As the commit was reverted this change was reverted too,
although likely correct.
Fixes: f8585ce655 ("[media] dvb-usb-cxusb: Geniatech T230C support")
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This reverts commit f8585ce655.
The T230C is handled by the dvb-usb-v2/dvbsky.c driver, which should
be preferred over a dvb-usb (v1) driver.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge HVR-975 is hybrid NTSC/PAL, QAM/ATSC, and DVB-C/T/T2 usb device.
Only ATSC/QAM front end is initially active. Second frontend support is
work in progress.
CX23102 + LG3306A/Si2168(WiP) + Si2157
Changes since v1:
- removed double semicolon
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a number of coding style issues at em28xx-video.
Fix most of them, by using checkpatch in strict mode to point
for it.
Automatic fixes were made with --fix-inplace, but those
were complemented by manual work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a number of coding style issues at em28xx-input.
Fix most of them, by using checkpatch in strict mode to point
for it.
Automatic fixes were made with --fix-inplace, but those
were complemented by manual work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a number of coding style issues at em28xx-i2c.
Fix most of them, by using checkpatch in strict mode to point
for it.
Automatic fixes were made with --fix-inplace, but those
were complemented by manual work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a number of coding style issues at em28xx-core.
Fix most of them, by using checkpatch in strict mode to point
for it.
Automatic fixes were made with --fix-inplace, but those
were complemented by manual work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is a complex loop there with identifies the em28xx
endpoints. It has lots of identations inside, and big names,
making harder to understand.
Simplify it by moving the main logic into a static function.
While here, rename "interface" var to "intf".
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a number of coding style issues, pointed by checkpatch
on strict mode.
Fix the ones that don't require code refactor here.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are some coding style issues at em28xx-camera.
Fix them, by using checkpatch in strict mode to point for it.
Automatic fixes with --fix-inplace were complemented by manual
work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a number of coding style issues at em28xx-audio.
Fix them, by using checkpatch in strict mode to point for it.
Automatic fixes with --fix-inplace were complemented by manual
work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use BIT() macros and fix one comment that is not following
the Kernel coding style.
It should be noticed that the registers bit masks should be
casted to unsigned char, as, otherwise, it would produce
warnings like:
drivers/media/usb/em28xx/em28xx-cards.c:81:33: warning: large integer implicitly truncated to unsigned type [-Woverflow]
{EM2820_R08_GPIO_CTRL, 0x6d, ~EM_GPIO_4, 10},
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There used to have a lot of coding style issues there. The
ones detected by checkpatch, in strict mode, got fixed.
Still, we need to work more on it, in order to document all
struct fields using kernel-doc macros, but this will be done
on some future patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most of the files there are missing a SPDX license tag. Add.
While here fix some DRIVER_LICENSE macro in order to reflect
the source file license, as some of the headers are GPL v2
only.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we're touching a lot on this file, let's solve several
Coding Style issues there using checkpatch --fix-inline --strict,
and manually adjusting the results.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is a typo at the several s5h14*.h headers: continuous were
spelled incorrectly.
Fix it with this script:
for i in $(git grep -l S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK); do
sed s,S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK,S5H1409_MPEGTIMING_CONTINUOUS_NONINVERTING_CLOCK,g -i $i
done
for i in $(git grep -l -i continous drivers/media); do sed s,CONTINOUS,CONTINUOUS,g -i $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The module probing logic there is a way more complex than
it should be, and requires some special magic to avoid
stack overflows when KASAN is enabled.
Solve it by creating ancillary functions to setup the
platform data and request module.
Now, the probing functions are cleaner and easier to understand.
As a side effect, the size of the module was reduced by
about 9.7% on x86_64:
Before this patch:
text data bss dec hex filename
51090 14192 96 65378 ff62 drivers/media/usb/em28xx/em28xx-dvb.o
After this patch:
text data bss dec hex filename
44743 14192 96 59031 e697 drivers/media/usb/em28xx/em28xx-dvb.o
Tested with a PCTV 461e device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With CONFIG_KASAN, the init function uses a large amount of kernel stack:
drivers/media/usb/em28xx/em28xx-dvb.c: In function 'em28xx_dvb_init.part.4':
drivers/media/usb/em28xx/em28xx-dvb.c:2061:1: error: the frame size of 3232 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
Using gcc-7 with -fsanitize-address-use-after-scope makes this even worse:
drivers/media/usb/em28xx/em28xx-dvb.c: In function 'em28xx_dvb_init':
drivers/media/usb/em28xx/em28xx-dvb.c:2069:1: error: the frame size of 4280 bytes is larger than 3072 bytes [-Werror=frame-larger-than=]
By splitting out each part of the switch/case statement that has its own local
variables into a separate function, no single one of them uses more than 500 bytes,
and with a noinline_for_stack annotation we can ensure that they are not merged
back together.
[mchehab@s-opensource.com: fix conflict with changeset
be7fd3c3a8 ("media: em28xx: Hauppauge DualHD second tuner functionality")]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the I2C speed is too slow, it should wait more for an
answer.
While here, change disconnected type from char to unsigned
int, just like all other bitmask fields there at em28xx
struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several em28xx static structs that can now be constified.
That caused a significant reduction at data segment:
Before:
text data bss dec hex filename
85017 59588 576 145181 2371d drivers/media/usb/em28xx/em28xx.o
After:
text data bss dec hex filename
112345 32292 576 145213 2373d drivers/media/usb/em28xx/em28xx.o
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Writing at the device's struct is evil, as two em28xx devices
may be using it. So, stop abusing it, storing the values
inside struct em28xx_dev.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The logic there should be called on two places. Also,
ideally, it should not be modifying the device struct.
So, change the logic accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While coherent memory is cheap on x86, it may cause performance
impacts on other archs. As we don't have any good reason to
use it, let's change the logic by allocating memory via kmalloc()
and letting the USB core to do the DMA mapping and memory free
for us.
While here, also fixes an issue that it was not de-allocating
memories if something gets wrong during memory block
allocation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a missing device to the driver table.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add additional pids to driver list
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Maximum 4 em28xx boards is too low, this can be maxed out by two devices.
This allows all the dvb adapters in the system to be em28xx if so desired.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge em28xx bulk devices exhibit continuity errors and corrupted
packets, when run in VMWare virtual machines. Unknown if other
manufacturers bulk models exhibit the same issue. KVM/Qemu is unaffected.
According to documentation the maximum packet multiplier for em28xx in bulk
transfer mode is 256 * 188 bytes. This changes the size of bulk transfers
to maximum supported value and have a bonus beneficial alignment.
Before:
After:
This sets up USB to expect just as many bytes as the em28xx is set to emit.
Successful usage under load afterwards natively and in both VMWare
and KVM/Qemu virtual machines.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set appropriate bulk/ISOC transfer multiplier on capture start.
This sets ISOC transfer to USB endpoint configuration
This sets bulk transfer to 48128 bytes (188 * 256)
The bulk multiplier is maximum allowed according to Empia.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
em28xx_duplicate_dev() is static. This were supposed to be
merged on the last patch, but somehow, I forgot "-a" when
I called git commit --amend.
Fixes: be7fd3c3a8 ("media: em28xx: Hauppauge DualHD second tuner functionality")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement use of secondary TS port on em28xx.
Adds has_dual_ts field, allows secondary demod/tuner to be
added to a single em28xx device.
Hauppauge DualHD models are configured to use this feature.
[mchehab@s-opensource.com: em28xx_duplicate_dev() should be static]
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* commit 'v4.16-rc4~0': (900 commits)
Linux 4.16-rc4
memremap: fix softlockup reports at teardown
libnvdimm: re-enable deep flush for pmem devices via fsync()
MAINTAINERS: take over Kconfig maintainership
vfio: disable filesystem-dax page pinning
kconfig: fix line number in recursive inclusion error message
Coccinelle: memdup: Fix typo in warning messages
i2c: octeon: Prevent error message on bus error
parisc: Reduce irq overhead when run in qemu
parisc: Use cr16 interval timers unconditionally on qemu
parisc: Check if secondary CPUs want own PDC calls
parisc: Hide virtual kernel memory layout
parisc: Fix ordering of cache and TLB flushes
kconfig: Update ncurses package names for menuconfig
kbuild/kallsyms: trivial typo fix
kbuild: test --build-id linker flag by ld-option instead of cc-ldoption
kbuild: drop superfluous GCC_PLUGINS_CFLAGS assignment
kconfig: Don't leak choice names during parsing
sh: fix build error for empty CONFIG_BUILTIN_DTB_SOURCE
kconfig: set SYMBOL_AUTO to the symbol marked with defconfig_list
...
Use %*ph format to print small buffer as hex string.
Remove newline at the end of the format string as it would be duplicated
by the one supplied as last argument.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Antonio Cardace <anto.cardace@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use %*phC format to print small buffers as hex strings
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Antonio Cardace <anto.cardace@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Given the following definitions from s2255drv.c
#define LINE_SZ_4CIFS_NTSC 640
#define LINE_SZ_2CIFS_NTSC 640
#define LINE_SZ_1CIFS_NTSC 320
and
#define LINE_SZ_4CIFS_PAL 704
#define LINE_SZ_2CIFS_PAL 704
#define LINE_SZ_1CIFS_PAL 352
f->fmt.pix.width possible values can be reduced to
LINE_SZ_4CIFS_NTSC or LINE_SZ_1CIFS_NTSC.
This patch removes unneeded if else blocks in vidioc_try_fmt_vid_cap
function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Christopher Díaz Riveros <chrisadr@gentoo.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for a new USB ID in this driver.
Signed-off-by: Ian Douglas Scott <ian@iandouglasscott.com>
[hans.verkuil@cisco.com: add commit message]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Quoting the original report:
It looks like there is a double-free vulnerability in Linux usbtv driver
on an error path of usbtv_probe function. When audio registration fails,
usbtv_video_free function ends up freeing usbtv data structure, which
gets freed the second time under usbtv_video_fail label.
usbtv_audio_fail:
usbtv_video_free(usbtv); =>
v4l2_device_put(&usbtv->v4l2_dev);
=> v4l2_device_put
=> kref_put
=> v4l2_device_release
=> usbtv_release (CALLBACK)
=> kfree(usbtv) (1st time)
usbtv_video_fail:
usb_set_intfdata(intf, NULL);
usb_put_dev(usbtv->udev);
kfree(usbtv); (2nd time)
So, as we have refcounting, use it
Reported-by: Yavuz, Tuba <tuba@ece.ufl.edu>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
After the move of videobuf2 into the common directory, selecting the
au0828 driver with CONFIG_V4L2 disabled started causing a link failure,
as we now attempt to build videobuf2 but it still requires v4l2:
ERROR: "v4l2_event_pending" [drivers/media/common/videobuf/videobuf2-v4l2.ko] undefined!
ERROR: "v4l2_fh_release" [drivers/media/common/videobuf/videobuf2-v4l2.ko] undefined!
ERROR: "video_devdata" [drivers/media/common/videobuf/videobuf2-v4l2.ko] undefined!
ERROR: "__tracepoint_vb2_buf_done" [drivers/media/common/videobuf/videobuf2-core.ko] undefined!
ERROR: "__tracepoint_vb2_dqbuf" [drivers/media/common/videobuf/videobuf2-core.ko] undefined!
ERROR: "v4l_vb2q_enable_media_source" [drivers/media/common/videobuf/videobuf2-core.ko] undefined!
We want to be able to build the core au0828 support without V4L2,
so this makes the 'select' conditional on V4L2, and refines the
dependencies in VIDEO_AU0828_V4L2 so it can only be enabled in
the exact conditions that have VIDEOBUF2_VMALLOC reachable.
Fixes: 03fbdb2fc2 ("media: move videobuf2 to drivers/media/common")
Fixes: 05439b1a36 ("[media] media: au0828 - convert to use videobuf2")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that we have support for a buffer counter and for
error flags, update them at DMX_DQBUF.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
After the move of videobuf2 into the common directory, selecting the
au0828 driver with CONFIG_V4L2 disabled started causing a link failure,
as we now attempt to build videobuf2 but it still requires v4l2:
ERROR: "v4l2_event_pending" [drivers/media/common/videobuf/videobuf2-v4l2.ko] undefined!
ERROR: "v4l2_fh_release" [drivers/media/common/videobuf/videobuf2-v4l2.ko] undefined!
ERROR: "video_devdata" [drivers/media/common/videobuf/videobuf2-v4l2.ko] undefined!
ERROR: "__tracepoint_vb2_buf_done" [drivers/media/common/videobuf/videobuf2-core.ko] undefined!
ERROR: "__tracepoint_vb2_dqbuf" [drivers/media/common/videobuf/videobuf2-core.ko] undefined!
ERROR: "v4l_vb2q_enable_media_source" [drivers/media/common/videobuf/videobuf2-core.ko] undefined!
This adds the same dependency in au0828 that the other users of videobuf2
have.
Fixes: 03fbdb2fc2 ("media: move videobuf2 to drivers/media/common")
Fixes: 05439b1a36 ("[media] media: au0828 - convert to use videobuf2")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit 828ee8c719 ("media: uvcvideo: Use ktime_t for timestamps")
changed to use ktime_t for timestamps. Older Kernels use a struct for
ktime_t, which requires the conversion function ktime_to_ns to be used on
some places. With this patch it will compile now also for older Kernel
versions.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While the sizeof is an operator and not a function, the preferred coding
style in the kernel is to enclose its operand in parentheses. To avoid
mixing multiple coding styles in the driver, use parentheses around all
sizeof operands.
While at it replace a kmalloc() with a kmalloc_array() to silence a
checkpatch warning triggered by this patch.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the __[su]{8,16,32} variant of integer types with the
non-underscored types as the code is internal to the driver, not exposed
to userspace.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The extern keyword isn't needed to declare functions in header files.
Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Microsoft HoloLens Sensors device has two separate frame descriptors
with the same dimensions, each with a single different frame interval:
VideoStreaming Interface Descriptor:
bLength 30
bDescriptorType 36
bDescriptorSubtype 5 (FRAME_UNCOMPRESSED)
bFrameIndex 1
bmCapabilities 0x00
Still image unsupported
wWidth 1280
wHeight 481
dwMinBitRate 147763200
dwMaxBitRate 147763200
dwMaxVideoFrameBufferSize 615680
dwDefaultFrameInterval 333333
bFrameIntervalType 1
dwFrameInterval( 0) 333333
VideoStreaming Interface Descriptor:
bLength 30
bDescriptorType 36
bDescriptorSubtype 5 (FRAME_UNCOMPRESSED)
bFrameIndex 2
bmCapabilities 0x00
Still image unsupported
wWidth 1280
wHeight 481
dwMinBitRate 443289600
dwMaxBitRate 443289600
dwMaxVideoFrameBufferSize 615680
dwDefaultFrameInterval 111111
bFrameIntervalType 1
dwFrameInterval( 0) 111111
Skip duplicate dimensions in enum_framesizes, let enum_frameintervals list
the intervals from both frame descriptors. Change set_streamparm to switch
to the correct frame index when changing the interval. This enables 90 fps
capture on a Lenovo Explorer Windows Mixed Reality headset.
[laurent.pinchart@ideasonboard.com: Renamed tmp_ival to ival]
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use flags the device exposes for UVC controls.
This allows the device to define which property flags are set.
Since some cameras offer auto-adjustments for properties (e.g. auto-gain),
the values of other properties (e.g. gain) can change in the camera.
Examining the flags ensures that the driver is aware of such properties.
Signed-off-by: Edgar Thier <info@edgarthier.net>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert all g/s_parm calls to g/s_frame_interval. This allows us
to remove the g/s_parm ops since those are a duplicate of
g/s_frame_interval.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=H9AS
-----END PGP SIGNATURE-----
Merge tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- videobuf2 was moved to a media/common dir, as it is now used by the
DVB subsystem too
- Digital TV core memory mapped support interface
- new sensor driver: ov7740
- several improvements at ddbridge driver
- new V4L2 driver: IPU3 CIO2 CSI-2 receiver unit, found on some Intel
SoCs
- new tuner driver: tda18250
- finally got rid of all LIRC staging drivers
- as we don't have old lirc drivers anymore, restruct the lirc device
code
- add support for UVC metadata
- add a new staging driver for NVIDIA Tegra Video Decoder Engine
- DVB kAPI headers moved to include/media
- synchronize the kAPI and uAPI for the DVB subsystem, removing the gap
for non-legacy APIs
- reduce the kAPI gap for V4L2
- lots of other driver enhancements, cleanups, etc.
* tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (407 commits)
media: v4l2-compat-ioctl32.c: make ctrl_is_pointer work for subdevs
media: v4l2-compat-ioctl32.c: refactor compat ioctl32 logic
media: v4l2-compat-ioctl32.c: don't copy back the result for certain errors
media: v4l2-compat-ioctl32.c: drop pr_info for unknown buffer type
media: v4l2-compat-ioctl32.c: copy clip list in put_v4l2_window32
media: v4l2-compat-ioctl32.c: fix ctrl_is_pointer
media: v4l2-compat-ioctl32.c: copy m.userptr in put_v4l2_plane32
media: v4l2-compat-ioctl32.c: avoid sizeof(type)
media: v4l2-compat-ioctl32.c: move 'helper' functions to __get/put_v4l2_format32
media: v4l2-compat-ioctl32.c: fix the indentation
media: v4l2-compat-ioctl32.c: add missing VIDIOC_PREPARE_BUF
media: v4l2-ioctl.c: don't copy back the result for -ENOTTY
media: v4l2-ioctl.c: use check_fmt for enum/g/s/try_fmt
media: vivid: fix module load error when enabling fb and no_error_inj=1
media: dvb_demux: improve debug messages
media: dvb_demux: Better handle discontinuity errors
media: cxusb, dib0700: ignore XC2028_I2C_FLUSH
media: ts2020: avoid integer overflows on 32 bit machines
media: i2c: ov7740: use gpio/consumer.h instead of gpio.h
media: entity: Add a nop variant of media_entity_cleanup
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ttq9
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- skip AER driver error recovery callbacks for correctable errors
reported via ACPI APEI, as we already do for errors reported via the
native path (Tyler Baicar)
- fix DPC shared interrupt handling (Alex Williamson)
- print full DPC interrupt number (Keith Busch)
- enable DPC only if AER is available (Keith Busch)
- simplify DPC code (Bjorn Helgaas)
- calculate ASPM L1 substate parameter instead of hardcoding it (Bjorn
Helgaas)
- enable Latency Tolerance Reporting for ASPM L1 substates (Bjorn
Helgaas)
- move ASPM internal interfaces out of public header (Bjorn Helgaas)
- allow hot-removal of VGA devices (Mika Westerberg)
- speed up unplug and shutdown by assuming Thunderbolt controllers
don't support Command Completed events (Lukas Wunner)
- add AtomicOps support for GPU and Infiniband drivers (Felix Kuehling,
Jay Cornwall)
- expose "ari_enabled" in sysfs to help NIC naming (Stuart Hayes)
- clean up PCI DMA interface usage (Christoph Hellwig)
- remove PCI pool API (replaced with DMA pool) (Romain Perier)
- deprecate pci_get_bus_and_slot(), which assumed PCI domain 0 (Sinan
Kaya)
- move DT PCI code from drivers/of/ to drivers/pci/ (Rob Herring)
- add PCI-specific wrappers for dev_info(), etc (Frederick Lawler)
- remove warnings on sysfs mmap failure (Bjorn Helgaas)
- quiet ROM validation messages (Alex Deucher)
- remove redundant memory alloc failure messages (Markus Elfring)
- fill in types for compile-time VGA and other I/O port resources
(Bjorn Helgaas)
- make "pci=pcie_scan_all" work for Root Ports as well as Downstream
Ports to help AmigaOne X1000 (Bjorn Helgaas)
- add SPDX tags to all PCI files (Bjorn Helgaas)
- quirk Marvell 9128 DMA aliases (Alex Williamson)
- quirk broken INTx disable on Ceton InfiniTV4 (Bjorn Helgaas)
- fix CONFIG_PCI=n build by adding dummy pci_irqd_intx_xlate() (Niklas
Cassel)
- use DMA API to get MSI address for DesignWare IP (Niklas Cassel)
- fix endpoint-mode DMA mask configuration (Kishon Vijay Abraham I)
- fix ARTPEC-6 incorrect IS_ERR() usage (Wei Yongjun)
- add support for ARTPEC-7 SoC (Niklas Cassel)
- add endpoint-mode support for ARTPEC (Niklas Cassel)
- add Cadence PCIe host and endpoint controller driver (Cyrille
Pitchen)
- handle multiple INTx status bits being set in dra7xx (Vignesh R)
- translate dra7xx hwirq range to fix INTD handling (Vignesh R)
- remove deprecated Exynos PHY initialization code (Jaehoon Chung)
- fix MSI erratum workaround for HiSilicon Hip06/Hip07 (Dongdong Liu)
- fix NULL pointer dereference in iProc BCMA driver (Ray Jui)
- fix Keystone interrupt-controller-node lookup (Johan Hovold)
- constify qcom driver structures (Julia Lawall)
- rework Tegra config space mapping to increase space available for
endpoints (Vidya Sagar)
- simplify Tegra driver by using bus->sysdata (Manikanta Maddireddy)
- remove PCI_REASSIGN_ALL_BUS usage on Tegra (Manikanta Maddireddy)
- add support for Global Fabric Manager Server (GFMS) event to
Microsemi Switchtec switch driver (Logan Gunthorpe)
- add IDs for Switchtec PSX 24xG3 and PSX 48xG3 (Kelvin Cao)
* tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe endpoint controller
PCI: endpoint: Fix EPF device name to support multi-function devices
PCI: endpoint: Add the function number as argument to EPC ops
PCI: cadence: Add host driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe host controller
PCI: Add vendor ID for Cadence
PCI: Add generic function to probe PCI host controllers
PCI: generic: fix missing call of pci_free_resource_list()
PCI: OF: Add generic function to parse and allocate PCI resources
PCI: Regroup all PCI related entries into drivers/pci/Makefile
PCI/DPC: Reformat DPC register definitions
PCI/DPC: Add and use DPC Status register field definitions
PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error()
PCI/DPC: Remove unnecessary RP PIO register structs
PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info()
PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info()
PCI/DPC: Make RP PIO log size check more generic
PCI/DPC: Rename local "status" to "dpc_status"
PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error()
...
Pull misc vfs updates from Al Viro:
"All kinds of misc stuff, without any unifying topic, from various
people.
Neil's d_anon patch, several bugfixes, introduction of kvmalloc
analogue of kmemdup_user(), extending bitfield.h to deal with
fixed-endians, assorted cleanups all over the place..."
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (28 commits)
alpha: osf_sys.c: use timespec64 where appropriate
alpha: osf_sys.c: fix put_tv32 regression
jffs2: Fix use-after-free bug in jffs2_iget()'s error handling path
dcache: delete unused d_hash_mask
dcache: subtract d_hash_shift from 32 in advance
fs/buffer.c: fold init_buffer() into init_page_buffers()
fs: fold __inode_permission() into inode_permission()
fs: add RWF_APPEND
sctp: use vmemdup_user() rather than badly open-coding memdup_user()
snd_ctl_elem_init_enum_names(): switch to vmemdup_user()
replace_user_tlv(): switch to vmemdup_user()
new primitive: vmemdup_user()
memdup_user(): switch to GFP_USER
eventfd: fold eventfd_ctx_get() into eventfd_ctx_fileget()
eventfd: fold eventfd_ctx_read() into eventfd_read()
eventfd: convert to use anon_inode_getfd()
nfs4file: get rid of pointless include of btrfs.h
uvc_v4l2: clean copyin/copyout up
vme_user: don't use __copy_..._user()
usx2y: don't bother with memdup_user() for 16-byte structure
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
The XC2028_I2C_FLUSH only needs to be implemented on a few
devices. Others can safely ignore it.
That prevents filling the dmesg with lots of messages like:
dib0700: stk7700ph_xc3028_callback: unknown command 2, arg 0
Cc: stable@vger.kernel.org
Fixes: 4d37ece757 ("[media] tuner/xc2028: Add I2C flush callback")
Reported-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Switch to a plain kzalloc() instead of pci_zalloc_coherent() to allocate
memory for the USB DMA.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Switch to a plain kzalloc() instead of pci_zalloc_coherent() to allocate
memory for the USB DMA.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There are a lot of places where sequences of space/tabs are
found. Get rid of all spaces before tabs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On several places, whitespaces are being used for indentation,
or even at the end of the line.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As reported on [1], this device needs this quirk to be able to
reliably initialise the webcam.
[1] https://sourceforge.net/p/linux-uvc/mailman/message/33791098/
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some UVC video cameras contain metadata in their payload headers. This
patch extracts that data, adding more clock synchronisation information,
on both bulk and isochronous endpoints and makes it available to the user
space on a separate video node, using the V4L2_CAP_META_CAPTURE capability
and the V4L2_BUF_TYPE_META_CAPTURE buffer queue type. By default, only the
V4L2_META_FMT_UVC pixel format is available from those nodes. However,
cameras can be added to the device ID table to additionally specify their
own metadata format, in which case that format will also become available
from the metadata node.
[Use put_unaligned instead of __put_unaligned_cpu64]
[Use put_unaligned for the sof field as well]
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently the UVC driver assigns a quirk bitmask to the .driver_info
field of struct usb_device_id. This patch instroduces a struct to store
quirks and possibly other per-device parameters in the future.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The V4L2 core populates the struct v4l2_capability device_caps field
from the same field in video_device. There's no need to handle that
manually in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Tested-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function will then be used to register the video device for metadata
capture.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Tested-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
uvc_video_get_ts() returns a 'struct timespec', but all its users
really want a nanoseconds variable anyway.
Changing the deprecated ktime_get_ts/ktime_get_real_ts to ktime_get
and ktime_get_real simplifies the code noticeably, while keeping
the resulting numbers unchanged.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
'struct timespec' works fine here, but we try to migrate
away from it in favor of ktime_t or timespec64. In this
case, using ktime_t produces the simplest code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pvr2_trace prints a newline at the end of the message string, so the
message string does not need to include a newline explicitly. Done
using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most of the I2C headers got moved a long time ago to
include/media/i2c. Stop including them at the patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The agreed format is to use /* */ comments inside header
files. Unfortunately, I ended by using // on a few ones.
Reported-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The pvrusb2 code appears to have a some old workaround code for xawtv that causes a
WARN() due to an unrecognized pixelformat 0 in v4l2_ioctl.c.
Since all other MPEG drivers fill this in correctly, it is a safe assumption that
this particular problem no longer exists.
While I'm at it, clean up the code a bit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the past, the same I2C address were used on multiple places.
After I2C rebinding changes, this is no longer needed. So, we
can just get rid of this header, placing the I2C address where
they belong, e. g. either at bttv driver or at tvtuner.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Using enums makes easier to document, as it can use kernel-doc
markups. It also allows cross-referencing, with increases the
kAPI readability.
Please notice that now cx88_querycap() has to have a default for
the VFL type, as there are more types than supported by the driver.
Acked-By: Mike Isely <isely@pobox.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These two devices ids are really just one device with multiple
addresses. Probing becomes much simpler if we simply fold this into
one i2c device with two address.
Note that this breaks the lirc_zilog driver, however we will teach
ir-kbd-i2c to do what lirc_zilog does in a later commit.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mygica T230 DVB-T/T2/C USB stick support. It uses the same FX2/Si2168
bridge/demodulator combo as the other devices supported by the driver,
but uses the Si2141 tuner.
Several DVB-T (MPEG2) and DVB-T2 (H.265) channels were tested, as well as
the included remote control.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dvb_frontend will call dvb_detach for:
- stb0899_detach in dvb_frontend_release and
- stb0899_release in __dvb_frontend_free
But we only do dvb_attach(stb0899_attach).
Increment the module refcount instead.
Signed-off-by: Wolfgang Rohdewald <wolfgang@rohdewald.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Xbox One Digital TV Tuner is a low-cost USB 2.0 multistandard TV tuner. It supports DVB-T, DVB-T2 and DVB-C broadcast standards.
USB bridge: DibCom 0700C
Demodulator: Panasonic MN88472
Tuner: TDA18250BHN
The demodulator requires firmware. Download one from here:
http://palosaari.fi/linux/v4l-dvb/firmware/MN88472/02/latest/
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix almost all of checkpatch --strict warnings.
The remaining warnings are about:
* macro REG16 (should be enclosed in parentheses)
* macro REG16 (Macro argument reuse)
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As reported by smatch:
drivers/media/usb/dvb-usb-v2/mxl111sf-demod.c:485 mxl111sf_demod_read_signal_strength() error: uninitialized symbol 'modulation'.
The mxl111sf_demod_read_signal_strength() just ignores if something
gets wrong while reading snr or modulation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Smatch gives two bogus warnings on this driver:
drivers/media/usb/dvb-usb-v2/dvbsky.c:336 dvbsky_s960_attach() error: uninitialized symbol 'i2c_adapter'.
drivers/media/usb/dvb-usb-v2/dvbsky.c:459 dvbsky_s960c_attach() error: uninitialized symbol 'i2c_adapter'.
Shut them up.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the tuner was split from m88rs2000 the attach function is in wrong
place.
Move to dm04_lme2510_tuner to trap errors on failure and removing
a call to lme_coldreset.
Prevents driver starting up without any tuner connected.
Fixes to trap for ts2020 fail.
LME2510(C): FE Found M88RS2000
ts2020: probe of 0-0060 failed with error -11
...
LME2510(C): TUN Found RS2000 tuner
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Warm start has no check as whether a genuine device has
connected and proceeds to next execution path.
Check device should read 0x47 at offset of 2 on USB descriptor read
and it is the amount requested of 6 bytes.
Fix for
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access as
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we're now using SPDX identifiers, on several
media drivers I wrote, add the proper SPDX, identifying
the license I meant.
As we're now using the short license, it doesn't make sense to
keep the original license text.
Also, fix MODULE_LICENSE to properly identify GPL v2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to the UVC specification, stream error events carry no data.
Fix a buffer overflow (that should be harmless given data alignment)
when reporting the stream error event by removing the data byte from the
message.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some cameras post inaccurate frame where next frame data overlap
it. this results in screen flicker, and it need to be prevented.
So this patch marks the buffer error to discard the frame where
buffer overflow.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
usb_endpoint_maxp() has an inline keyword and searches for bits[10:0]
by & operation with 0x7ff. So, we can remove the duplicate & operation
with 0x7ff.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Microsoft HoloLense UVC sensor uses D3DFMT instead of FOURCC when
exposing formats. This adds support for D3DFMT_L8 as exposed from
the Acer Windows Mixed Reality Headset.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is no need to #define the license of the driver, just put it in
the MODULE_LICENSE() line directly as a text string.
This allows tools that check that the module license matches the source
code license to work properly, as there is no need to unwind the
unneeded dereference.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Johan Hovold <johan@kernel.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Reported-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cam->buffers[] array has cam->num_frames elements so the > needs to
be changed to >= to avoid going beyond the end of the array. The
->buffers[] array is allocated in cpia2_allocate_buffers() if you want
to confirm.
Fixes: ab33d5071d ("V4L/DVB (3376): Add cpia2 camera support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The firmware timestamp is an unsigned 32-bit value, but we copy it into
a signed 32-bit variable, so we can theoretically get an overflow in
the calculation when the timestamp is between 2038 and 2106.
This changes the temporary variable to time64_t and changes the deprecated
time_to_tm() over to time64_to_tm() accordingly.
There is still an overflow in y2106, but that is a limitation of the
firmware interface, not a kernel problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
fixes intermittent soft reboot issue with firmware load
increases wait time of reset, as required by HW
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Note that the inputs for the Composite and S-Video are inverted in
regard to most of the other boards using a cx231xx chip.
Signed-off-by: Romain Reignier <r.reignier@robopec.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Using the ARRAY_SIZE macro improves the readability of the code. Also,
it is not always useful to use a variable to store this constant
calculated at compile time.
Found with Coccinelle with the following semantic patch:
@r depends on (org || report)@
type T;
T[] E;
position p;
@@
(
(sizeof(E)@p /sizeof(*E))
|
(sizeof(E)@p /sizeof(E[...]))
|
(sizeof(E)@p /sizeof(T))
)
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use a more typical logging style.
The current macro hides the gspca_dev argument so add it to the
macro uses instead.
Miscellanea:
o Add missing '\n' terminations to formats
o Realign arguments to open parenthesis
o Remove commented out uses of PDEBUG
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use a more typical kernel logging style.
The current macro hides the gspca_dev argument so add it to the
macro uses instead.
Miscellanea:
o Add missing '\n' terminations to formats
o Realign arguments to open parenthesis
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We free the stk_camera device too early. It's allocate first in probe
and it should be freed last in stk_camera_disconnect().
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Here, hdpvr_register_videodev() is responsible for setup and
register a video device. Also defining and initializing a worker.
hdpvr_register_videodev() is calling by hdpvr_probe at last.
So no need to flush any work here.
Unregister v4l2, free buffers and memory. If hdpvr_probe() will fail.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate the read-only u8 array buf on the stack at run time but
instead make it static const; makes object code smaller saving over 480
bytes:
Before:
text data bss dec hex filename
33030 65936 192 99158 18356 drivers/media/usb/dvb-usb/cxusb.o
After:
text data bss dec hex filename
32446 66032 192 98670 1816e drivers/media/usb/dvb-usb/cxusb.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several comments are wrongly tagged as kernel-doc, causing
those warnings:
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'irq'
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'data'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'solo_dev'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'ch'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'qp'
drivers/media/usb/pwc/pwc-dec23.c:652: warning: Cannot understand *
on line 652 - I thought it was a doc line
drivers/media/usb/dvb-usb/cinergyT2-fe.c:40: warning: No description found for parameter 'op'
drivers/media/usb/dvb-usb/friio-fe.c:301: warning: Cannot understand * (reg, val) commad list to initialize this module.
on line 301 - I thought it was a doc line
drivers/media/rc/streamzap.c:201: warning: No description found for parameter 'urb'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'intf'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'id'
drivers/media/rc/streamzap.c:464: warning: No description found for parameter 'interface'
drivers/media/i2c/ov5647.c:432: warning: Cannot understand * @short Subdev core operations registration
on line 432 - I thought it was a doc line
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'd'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'addr'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wlen'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rlen'
drivers/media/platform/vim2m.c:350: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/tua6100.c:34: warning: cannot understand function prototype: 'struct tua6100_priv '
drivers/media/platform/sti/hva/hva-h264.c:140: warning: cannot understand function prototype: 'struct hva_h264_stereo_video_sei '
drivers/media/platform/sti/hva/hva-h264.c:150: warning: Cannot understand * @frame_width: width in pixels of the buffer containing the input frame
on line 150 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:356: warning: Cannot understand * @ slice_size: slice size
on line 356 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:369: warning: Cannot understand * @ bitstream_size: bitstream size
on line 369 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:395: warning: Cannot understand * @seq_info: sequence information buffer
on line 395 - I thought it was a doc line
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fe'
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fw'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'n'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'd'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_i'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_f'
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:83: warning: cannot understand function prototype: 'struct ttusb '
drivers/media/platform/sh_veu.c:277: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/zl10036.c:33: warning: cannot understand function prototype: 'int zl10036_debug; '
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'state'
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'frequency'
drivers/media/platform/rcar_fdp1.c:1139: warning: No description found for parameter 'priv'
drivers/media/platform/ti-vpe/vpe.c:933: warning: No description found for parameter 'priv'
drivers/media/usb/gspca/ov519.c:36: warning: No description found for parameter 'fmt'
drivers/media/usb/dvb-usb/dib0700_devices.c:3367: warning: No description found for parameter 'adap'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A new usbid of UTV007 is found in a newly bought device.
The usbid is 1f71:3301.
The ID on the chip is:
UTV007
A89029.1
1520L18K1
Both video and audio is tested with the modified usbtv driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Siano driver doesn't use kernel-doc markups. While it
would be wanderful to convert to use it, it is probably
not worth the time.
So, instead of solving all problems there, just make
sure that it won't produce dozens of warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This mechanically converts all remaining cases of ancient open-coded timer
setup with the old setup_timer() API, which is the first step in timer
conversions. This has no behavioral changes, since it ultimately just
changes the order of assignment to fields of struct timer_list when
finding variations of:
init_timer(&t);
f.function = timer_callback;
t.data = timer_callback_arg;
to be converted into:
setup_timer(&t, timer_callback, timer_callback_arg);
The conversion is done with the following Coccinelle script, which
is an improved version of scripts/cocci/api/setup_timer.cocci, in the
following ways:
- assignments-before-init_timer() cases
- limit the .data case removal to the specific struct timer_list instance
- handling calls by dereference (timer->field vs timer.field)
spatch --very-quiet --all-includes --include-headers \
-I ./arch/x86/include -I ./arch/x86/include/generated \
-I ./include -I ./arch/x86/include/uapi \
-I ./arch/x86/include/generated/uapi -I ./include/uapi \
-I ./include/generated/uapi --include ./include/linux/kconfig.h \
--dir . \
--cocci-file ~/src/data/setup_timer.cocci
@fix_address_of@
expression e;
@@
init_timer(
-&(e)
+&e
, ...)
// Match the common cases first to avoid Coccinelle parsing loops with
// "... when" clauses.
@match_immediate_function_data_after_init_timer@
expression e, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
@match_immediate_function_data_before_init_timer@
expression e, func, da;
@@
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@match_function_and_data_after_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
... when != func = e2
when != da = e3
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
@match_function_and_data_before_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
... when != func = e2
when != da = e3
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@r1 exists@
expression t;
identifier f;
position p;
@@
f(...) { ... when any
init_timer@p(\(&t\|t\))
... when any
}
@r2 exists@
expression r1.t;
identifier g != r1.f;
expression e8;
@@
g(...) { ... when any
\(t.data\|t->data\) = e8
... when any
}
// It is dangerous to use setup_timer if data field is initialized
// in another function.
@script:python depends on r2@
p << r1.p;
@@
cocci.include_match(False)
@r3@
expression r1.t, func, e7;
position r1.p;
@@
(
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
... when != func = e7
-t.function = func;
|
-t.function = func;
... when != func = e7
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
|
-init_timer@p(t);
+setup_timer(t, func, 0UL);
... when != func = e7
-t->function = func;
|
-t->function = func;
... when != func = e7
-init_timer@p(t);
+setup_timer(t, func, 0UL);
)
Signed-off-by: Kees Cook <keescook@chromium.org>
-----BEGIN PGP SIGNATURE-----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=d9nT
-----END PGP SIGNATURE-----
Merge tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation for digital TV (both kAPI and uAPI) are now in sync
with the implementation (except for legacy/deprecated ioctls). This
is a major step, as there were always a gap there
- New sensor driver: imx274
- New cec driver: cec-gpio
- New platform driver for rockship rga and tegra CEC
- New RC driver: tango-ir
- Several cleanups at atomisp driver
- Core improvements for RC, CEC, V4L2 async probing support and DVB
- Lots of drivers cleanup, fixes and improvements.
* tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (332 commits)
dvb_frontend: don't use-after-free the frontend struct
media: dib0700: fix invalid dvb_detach argument
media: v4l2-ctrls: Don't validate BITMASK twice
media: s5p-mfc: fix lockdep warning
media: dvb-core: always call invoke_release() in fe_free()
media: usb: dvb-usb-v2: dvb_usb_core: remove redundant code in dvb_usb_fe_sleep
media: au0828: make const array addr_list static
media: cx88: make const arrays default_addr_list and pvr2000_addr_list static
media: drxd: make const array fastIncrDecLUT static
media: usb: fix spelling mistake: "synchronuously" -> "synchronously"
media: ddbridge: fix build warnings
media: av7110: avoid 2038 overflow in debug print
media: Don't do DMA on stack for firmware upload in the AS102 driver
media: v4l: async: fix unregister for implicitly registered sub-device notifiers
media: v4l: async: fix return of unitialized variable ret
media: imx274: fix missing return assignment from call to imx274_mode_regs
media: camss-vfe: always initialize reg at vfe_set_xbar_cfg()
media: atomisp: make function calls cleaner
media: atomisp: get rid of storage_class.h
media: atomisp: get rid of wrong stddef.h include
...
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
Check on return value and goto instruction is redundant as the code
that follows is the goto label err.
Addresses-Coverity-ID: 1268783
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate array addr_list on the stack but instead make it
static. Makes the object code smaller by over 360 bytes:
Before:
text data bss dec hex filename
8036 1488 192 9716 25f4 au0828-input.o
After:
text data bss dec hex filename
7696 1488 192 9376 24a0 au0828-input.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Trivial fix to spelling mistake in error message text
[mchehab@s-opensource.org: folded all similar patches into one]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Mike Isely <isely@pobox.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-media@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-By: Mike Isely <isely@pobox.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Variable j is being set to zero before a loop and also
immediately inside the loop and is not used after the loop.
Hence the first assignment is redundant and can be removed.
Cleans up clang warning:
drivers/media/usb/gspca/gspca.c:1078:2: warning: Value stored
to 'j' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Variable index is set to zero and then set to zero again
a few lines later in a for loop initialization. Remove the
redundant setting of index to zero. Cleans up the clang
warning:
drivers/media/usb/dvb-usb-v2/mxl111sf-i2c.c:519:3: warning: Value
stored to 'index' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Because the brightness and contrast controls share a register,
usbtv_s_ctrl needs to read the existing values for both controls before
inserting the new value. However, the code accidentally wrote to the
registers (from an uninitialised stack array), rather than reading them.
The user-visible effect of this was that adjusting the brightness would
also set the contrast to a random value, and vice versa -- so it wasn't
possible to correctly adjust the brightness of usbtv's video output.
Tested with an "EasyDAY" UTV007 device.
Fixes: c53a846c48 ("usbtv: add video controls")
Signed-off-by: Adam Sampson <ats@offog.org>
Reviewed-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Bhumika Goyal <bhumirks@gmail.com>
Cc: Mike Isely <isely@pobox.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
usb_endpoint_maxp() has an inline keyword and searches for bits[10:0]
by & operation with 0x7ff. So, we can remove the duplicate & operation
with 0x7ff.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only passed to the const argument of the
function videobuf_queue_vmalloc_init in the file referencing it.
Also, make the declaration in the header const.
Structure found using Coccienlle and changes done by hand.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Evromedia USB Full Hybrid Full HD (1b80:d3b2) has IR on Interface 0.
Remote controller supplied with this tuner fully compatible
with RC_MAP_MSI_DIGIVOX_III.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make vb2_ops const as they are only stored in the const field of a
vb2_queue structure. Make the declarations const too.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- Delete seven error messages for a failed memory allocation
- Adjust seven checks for null pointers
- Use common error handling code in tm6000_usb_probe()
- Adjust jump targets so that the function "kfree" will be always called
with a non-null pointer.
- Delete an initialisation for the local variable "dev"
which became unnecessary with this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This callback is not actually doing anything but making it to
return an error depending on the DTV frontend command. Well,
that could break userspace for no good reason, and, if needed,
should be implemented, instead, at set_frontend() callback.
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure to check that we actually have an Interface Association
Descriptor before dereferencing it during probe to avoid dereferencing a
NULL-pointer.
Fixes: e0d3bafd02 ("V4L/DVB (10954): Add cx231xx USB driver")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't populate const arrays on the stack, instead make them
static. Makes the object code smaller by over 5200 bytes:
Before:
text data bss dec hex filename
58259 8880 128 67267 106c3 ov519.o
After:
text data bss dec hex filename
52155 9776 128 62059 f26b ov519.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only the nec protocol is understood, but then it doesn't pass on
the full scancode and it ignores the nec repeats its own remote
sends, so holding buttons does not work.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
"IR-receiver inside an USB DVB receiver" is not descriptive and we have
a proper name available.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This receiver only accepts nec16 messages, I've tried many other protocols
and they're all dropped.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The help text should be indented by at least two spaces after the
'help' separator. This is both good practice and the media_build system
for building media drivers makes this assumption.
I went through all Kconfigs under drivers/media and fixed any bad help
sections. This makes it conform to the common practice and should fix
problems with 'make menuconfig' when using media_build. This is due to
a "WARNING" message that media_build can insert in the Kconfig and that
assumes the help text is indented by at least two spaces. If not, then the
Kconfig becomes invalid and 'make menuconfig' fails.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Thomas Kaiser <linux-dvb@kaiser-linux.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate the array rc_nec_tab on the stack, instead make it
static const. Makes the object code smaller by over 620 bytes:
Before:
text data bss dec hex filename
49511 17040 64 66615 10437 rtl28xxu.o
After:
text data bss dec hex filename
48825 17104 64 65993 101c9 rtl28xxu.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used in a copy operation.
Done using Coccinelle.
@match disable optional_qualifier@
identifier s;
@@
static struct i2c_client s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
position ref.p;
identifier match.s,f,c;
expression e;
@@
(
e = s@p
|
e = s@p.f
|
c(...,s@p.f,...)
|
c(...,s@p,...)
)
@bad depends on !good1@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct i2c_client s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written !…
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
[mchehab@s-opensoure.com: merge similar patches into one]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
[mchehab@s-opensource.com: fold several similar patches into one]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dvb_usb_device_description structures are only used during a copy
operation. Therefore, declare them as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written !…
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only stored in a const field of a
video_device structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used during a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When RC_CORE is a loadable module, and au0828 is built-in including
the RC support, we get a link error:
drivers/media/usb/au0828/au0828-input.o: In function `au0828_get_key_au8522':
au0828-input.c:(.text+0x474): undefined reference to `ir_raw_event_store'
drivers/media/usb/au0828/au0828-input.o: In function `au0828_rc_register':
au0828-input.c:(.text+0x7c8): undefined reference to `rc_allocate_device'
au0828-input.c:(.text+0x8f8): undefined reference to `rc_register_device'
This adds an additional dependency, similar to the one for em28xx,
to ensure the broken configuration is never used.
Fixes: 2fcfd317f6 ("[media] au0828: add support for IR on HVR-950Q")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Reviewing the delta between cppcheck output of v4.9.39 and v4.9.40
stable updates, I stumbled on the new warning:
mxl111sf.c:80: (warning) Possible null pointer dereference: rbuf
Since copying state->rcvbuf into rbuf is not needed in the 'write-only'
scenario (i.e. calling mxl111sf_ctrl_msg() from mxl111sf_i2c_send_data()
or from mxl111sf_write_reg()), bypass memcpy() in this case.
Fixes: d90b336f3f ("[media] mxl111sf: Fix driver to use heap allocate buffers for USB messages")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Call mutex_unlock and free dev on failure.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If dw2102_probe() fails on dvb_usb_device_init(), then memleak occurs.
The patch adds deallocation to the error path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Reviewed-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Calling i2c_unregister_device for a demod driver destroys the frontend object.
Later it is accessed by calling dvb_unregister_frontend and
dvb_frontend_detach.
In some cases this leads to a general protection fault with this
callstack:
dvb_unregister_frontend+0x25/0x50 [dvb_core]
dvb_fini+0xdb/0x160 [cx231xx_dvb]
cx231xx_unregister_extension+0x3d/0xb0 [cx231xx]
cx231xx_dvb_unregister+0x10/0x809 [cx231xx_dvb]
SyS_delete_module+0x18a/0x240
? exit_to_usermode_loop+0x7b/0x80
entry_SYSCALL_64_fastpath+0x17/0x98
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The calculation of the left volume looks suspect, the value of
0x1f - ((val << 8) & 0x1f) is always 0x1f. The debug prior to the
assignment of value[1] prints the left volume setting using the
calculation 0x1f - (val >> 8) & 0x1f which looks correct to me.
Fix the left volume by using the correct expression as used in
the debug.
Detected by CoverityScan, CID#146140 ("Wrong operator used")
Fixes: 850d24a5a8 ("[media] em28xx-alsa: add mixer support for AC97 volume controls")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used in a copy operation.
Done using Coccinelle
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used in a copy operation or
are stored in the algo field of i2c_adapter structure, which is const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
RC_TYPE is confusing and it's just the protocol. So rename it.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When an ir-spi is registered, you get this message.
rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
"Unspecified device" refers to input_name, which makes no sense for IR
TX only devices. So, rename to device_name.
Also make driver_name const char* so that no casts are needed anywhere.
Now ir-spi reports:
rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
uvc_subdev_ops is only passed as the second argument of
v4l2_subdev_init, which is const, so uvc_subdev_ops can be
const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When adding support for metadata nodes, we'll have to keep video
devices registered until all metadata nodes are closed too. Since
this has nothing to do with stream counting, replace the nstreams
atomic variable with a reference counter.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to documentation of struct vb2_ops the .queue_setup() callback
should return an error if the number of planes parameter contains an
invalid value on input. Fix this instead of ignoring the value.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The size of uvc_control_mapping is user controlled leading to a
potential heap overflow in the uvc driver. This adds a check to verify
the user provided size fits within the bounds of the defined buffer
size.
Originally-from: Richard Simmons <rssimmo@amazon.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Section 9.2.6.4 of USB 2.0/3.x specification describes that
"device must be able to return the first data packet to host within
500 ms of receipt of the request. For subsequent data packet, if any,
the device must be able to return them within 500 ms".
This is to fix incorrect timeout and change it from 300 ms to 500 ms
to meet the timing specified by specification for Get Request.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These videobuf_queue_ops structures are only passed as the second
argument to videobuf_queue_vmalloc_init, which is declared as const.
Thus the videobuf_queue_ops structures themselves can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct videobuf_queue_ops i@p = { ... };
@ok1@
identifier r.i;
expression e1;
position p;
@@
videobuf_queue_vmalloc_init(e1,&i@p,...)
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct videobuf_queue_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct videobuf_queue_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These videobuf_queue_ops structures are only passed as the second
argument to videobuf_queue_vmalloc_init, which is declared as const.
Thus the videobuf_queue_ops structures themselves can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct videobuf_queue_ops i@p = { ... };
@ok1@
identifier r.i;
expression e1;
position p;
@@
videobuf_queue_vmalloc_init(e1,&i@p,...)
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct videobuf_queue_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct videobuf_queue_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These videobuf_queue_ops structures are only passed as the second
argument to videobuf_queue_vmalloc_init, which is declared as const.
Thus the videobuf_queue_ops structures themselves can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct videobuf_queue_ops i@p = { ... };
@ok1@
identifier r.i;
expression e1;
position p;
@@
videobuf_queue_vmalloc_init(e1,&i@p,...)
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct videobuf_queue_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct videobuf_queue_ops i = { ... };
// </smpl>
In the first case, there is a second commented call to
videobuf_queue_sg_init with the structure as the second argument. If that
code will be uncommented, the const will remain correct, because the second
parameter of that function is also const.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
'drivers/media/usb/b2c2/flexcop-usb.c' Fix checkpatch.pl error:
ERROR: space prohibited before open square bracket '['.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This prevents potentially scary debug messages from the i2c core.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
No one cares anyway.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While at it, change the type of the previously always-zero i2c_rc
member to int, matching the returned type from i2c_add_adapter.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the new CEC_CAP_DEFAULTS define in the adv, vivid, pulse8 and
rainshadow CEC drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This field will be removed as it is not needed anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The persistent_config option is used to make the CEC settings persistent by using
the eeprom inside the device to store this information. This was on by default, which
caused confusion since this device now behaves differently from other CEC devices
which all come up unconfigured.
Another reason for doing this now is that I hope a more standard way of selecting
persistent configuration will be created in the future. And for that to work all
CEC drivers should behave the same and come up unconfigured by default.
None of the open source CEC applications are using this CEC framework at the moment
so change this behavior before it is too late.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Antti Palosaari