DT kernel on da850-evm comes up with garbled UART logs. This is because
of mismatch in actual module clock rate and rate specified(clock-frequency)
in DT blob. kernel should not assume or depend on bootloaders clock
configuration, instead let it find the clock rate at runtime.
Issue discussed here before arriving on this implementation:
"ARM: davinci: da850 evm: update clock rate for UART 1/2 DT nodes"
https://patchwork.kernel.org/patch/2162271/
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add ethernet device tree node information and pinmux for mii to da850 by
providing interrupt details and local mac address.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add mdio device tree node information to da850 by
providing register details and bus frequency of mdio.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
function-mask DT property is now a mask for a pin at each pin offset
inside a given pincontrol register. Fix DA850 DT data to reflect
this change.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
[nsekhar@ti.com: reword commit message for clarity]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Replace /include/ by #include for da850 device tree files, in order to
use the C pre-processor, making use of #define features possible.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add da850 EHRPWM & ECAP DT node along with pin-mux details.
Also adds OF_DEV_AUXDATA for EHRPWM & ECAP driver to use EHRPWM & ECAP
clock.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add I2C0 device tree and pin muxing information to da850-evm.
Also, add OF_DEV_AUXDATA for I2C0 controller driver in da850
board dt file to use I2C0 clock.
Verified i2c0 node gets created in sys class interface as
"/sys/class/i2c-dev/i2c-0/subsystem/i2c-0".
nsekhar@ti.com: tested using i2cdetect and i2cdump.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add NAND driver DT node and related pinctrl DT data to export NAND
functionality on da850 evm.
Signed-off-by: Kumar, Anil <anilkumar.v@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
For DT, DaVinci platform can use pinctrl-single driver for handling
padconf registers.
Enable PINCTRL Kconfig for MACH_DA8XX_DT platform. Add required
pinctrl DT entries in da850 dts file.
Test procedure
1)Populate DT file with NAND node information.
2)Populate board DT file with pinmux information for NAND.
3)Boot and confirm NAND is detected by the kernel.
4)cat /proc/mtd to show partitions.
Signed-off-by: Kumar, Anil <anilkumar.v@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add DT data for DA850 SoC. Only interrupt controller and
serial port information is being added at this time.
Signed-off-by: Heiko Schocher <hs@denx.de>
[nsekhar@ti.com: refactored DT data into SoC specific and
board specific and include SoC data into .dtsi file]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Peter Ujfalusi