This patch adds watchdog support by installing shmobile_boot_vector_gen2
to ICRAM1 when enough memory is available, in which case we also keep a
copy of MPIDR to complete the reset vector logic.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On R-Car Gen2 and RZ/G1 platforms, we use the SBAR registers to make non
boot CPUs run a routine designed to bring up SMP and deal with hot plug.
The value contained in the SBAR registers is not initialized by a WDT
triggered reset, which means that after a WDT triggered reset we jump
to the SMP bring up routine, preventing the system from executing the
bootrom code.
The purpose of this patch is to jump to the bootrom code in case of a
WDT triggered reset, and keep the SMP functionality untouched.
In order to tell if the code had been called due to the WDT overflowing
we are testing WOVF from register RWTCSRA.
The new function shmobile_boot_vector_gen2 isn't replacing
shmobile_boot_vector for backward compatibility reasons. The kernel
will install the best option (either shmobile_boot_vector or
shmobile_boot_vector_gen2) to ICRAM1 after parsing the device tree,
according to the amount of memory available.
Since shmobile_boot_vector has become bigger, "reg" property of nodes
compatible with "renesas,smp-sram" now need to be set to a value
greater or equal to "<0 0x60>".
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: dropped #ifdef from common.h]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On systems with two regulators, a bogus error message is printed on
success:
i2c 6-0058: i2c error 2
While adding support for Stout, the number of messages to send was
made variable, but the corresponding return value check of
i2c_transfer() wasn't updated.
Fixes: ff938cd14d ("ARM: shmobile: stout: enable R-Car Gen2 regulator quirk")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Regulator setup is suboptimal on H2 Stout too. The Stout newly has
two DA9210 regulators, so the quirk is extended to handle another
DA9210 at i2c address 0x70.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are
OMAP, Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now
with a Quad-Core ARM Cortex-A7. According to the manufacturer,
it is intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family
of chips meant for managed gigabit ethernet switches, based
around a Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2
and Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jlJ2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are OMAP,
Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now with a
Quad-Core ARM Cortex-A7. According to the manufacturer, it is
intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of
chips meant for managed gigabit ethernet switches, based around a
Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2 and
Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module
ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER
arm64: defconfig: enable CONFIG_GPIO_UNIPHIER
ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b
ARM: meson: Add SMP bringup code for Meson8 and Meson8b
ARM: smp_scu: allow the platform code to read the SCU CPU status
ARM: smp_scu: add a helper for powering on a specific CPU
dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation
ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init()
ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init()
ARM: defconfig: select the right SX150X driver
arm64: defconfig: Enable QCOM_IOMMU
arm64: Add ThunderX drivers to defconfig
arm64: defconfig: Enable Tegra PCI controller
cpufreq: imx6q: Move speed grading check to cpufreq driver
arm64: defconfig: re-enable Qualcomm DB410c USB
ARM: configs: stm32: Add MDMA support in STM32 defconfig
ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
...
* pm-domains:
PM / Domains: Fix genpd to deal with drivers returning 1 from ->prepare()
PM / domains: Rework governor code to be more consistent
PM / Domains: Remove gpd_dev_ops.active_wakeup() callback
soc: rockchip: power-domain: Use GENPD_FLAG_ACTIVE_WAKEUP
soc: mediatek: Use GENPD_FLAG_ACTIVE_WAKEUP
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ACTIVE_WAKEUP
PM / Domains: Allow genpd users to specify default active wakeup behavior
PM / Domains: Add support to select performance-state of domains
PM / Domains: Rename genpd internals from pm_genpd_* to genpd_*
Set the newly introduced GENPD_FLAG_ACTIVE_WAKEUP, which allows to
remove the driver's own "always true" callback.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bugfix for the SMP case broke the build for the UP case:
arch/arm/mach-shmobile/headsmp-apmu.o: In function `shmobile_boot_apmu':
(.text+0x34): undefined reference to `secondary_startup'
The assembler file mixes code that is used for SMP with code
that we also need on a single-CPU build, so I'm leaving it
always enabled in the Makefile, but enclose the SMP code
in an #ifdef.
Fixes: fd45a136ff6 ("ARM: shmobile: rcar-gen2: Make sure CNTVOFF is initialized on CA7/15")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On Cortex-A7, the arch timer CNTVOFF register is uninitialized.
Ideally it should be initialized by the boot loader, but it isn't.
For the boot CPU, CNTVOFF is initialized by Linux since commit
9ce3fa6816 ("ARM: shmobile: rcar-gen2: Add CA7 arch_timer
initialization for r8a7794").
For secondary CPU cores, no such initialization is done.
Hence when enabling SMP on r8a7794, the kernel log is spammed with:
WARNING: Underflow in clocksource 'arch_sys_counter' observed, time update ignored.
Please report this, consider using a different clocksource, if possible.
Your kernel is probably still fine.
As Marc Zyngier pointed out that Cortex-A15 and Cortex-A7 are similar with
respect to CNTVOFF, we have been very lucky this just worked on R-Car
Gen2 SoCs with Cortex-A15 cores.
To fix this:
- Move the existing inline asm code to initialize CNTVOFF to an
assembler source file (adding comments and replacing hardcoded
constants by definitions in the process), so it can be reused,
- Perform the initialization of CNTVOFF on the boot CPU (Cortex-A15 or
Cortex-A7) on all R-Car Gen2 and RZ/G1 parts,
- Wrap the standard secondary_startup() routine inside a routine which
initializes CNTVOFF.
Based on patches by Hisashi Nakamura in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Add debug-ll support to RZ/G1M (r8a7743) SoC
Chris Paterson says, "RZ/G1M uses SCIF0 for the debug console, like most
of the R-Car Gen2 SoCs."
* Remove ARCH_SHMOBILE_MULTI
Geert Uytterhoeven says, "The migration from ARCH_SHMOBILE_MULTI to
ARCH_RENESAS has been completed in v4.12..."
* Correct arch timer frequency on RZ/G1M (r8a7743) SoC
Geert Uytterhoeven says, "According to the datasheet, the frequency of
the ARM architecture timer on RZ/G1E depends on the frequency of the ZS
clock..."
* Add support for CPG/MSSR bindings
Geert Uytterhoeven says, "When using the new CPG/MSSR bindings, there is
no longer a "renesas,rcar-gen2-cpg-clocks" node, and the code to obtain
the external clock crystal frequency falls back to a default of 20 MHz.
While this is correct for all upstream R-Car Gen2 and RZ/G1 boards, this
is not necessarily the case for out-of-tree third party boards.
Add support for finding the external clock crystal oscillator on RZ/G1M,
and on R-Car H2, M2-W, and M2-N using the new CPG/MSSR bindings, through
the corresponding "renesas,r8a77xx-cpg-mssr" nodes."
* Obtain jump stub region from DT
Geert Uytterhoeven says, "Add support for obtaining from DT the SRAM
region to store the jump stub for CPU core bringup, according to the
renesas,smp-sram DT bindings."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PJul
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Renesas ARM Based SoC Updates for v4.14" Simon Horman:
* Add debug-ll support to RZ/G1M (r8a7743) SoC
Chris Paterson says, "RZ/G1M uses SCIF0 for the debug console, like most
of the R-Car Gen2 SoCs."
* Remove ARCH_SHMOBILE_MULTI
Geert Uytterhoeven says, "The migration from ARCH_SHMOBILE_MULTI to
ARCH_RENESAS has been completed in v4.12..."
* Correct arch timer frequency on RZ/G1M (r8a7743) SoC
Geert Uytterhoeven says, "According to the datasheet, the frequency of
the ARM architecture timer on RZ/G1E depends on the frequency of the ZS
clock..."
* Add support for CPG/MSSR bindings
Geert Uytterhoeven says, "When using the new CPG/MSSR bindings, there is
no longer a "renesas,rcar-gen2-cpg-clocks" node, and the code to obtain
the external clock crystal frequency falls back to a default of 20 MHz.
While this is correct for all upstream R-Car Gen2 and RZ/G1 boards, this
is not necessarily the case for out-of-tree third party boards.
Add support for finding the external clock crystal oscillator on RZ/G1M,
and on R-Car H2, M2-W, and M2-N using the new CPG/MSSR bindings, through
the corresponding "renesas,r8a77xx-cpg-mssr" nodes."
* Obtain jump stub region from DT
Geert Uytterhoeven says, "Add support for obtaining from DT the SRAM
region to store the jump stub for CPU core bringup, according to the
renesas,smp-sram DT bindings."
* tag 'renesas-soc-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove ARCH_SHMOBILE_MULTI
ARM: shmobile: rcar-gen2: Correct arch timer frequency on RZ/G1E
ARM: shmobile: rcar-gen2: Add support for CPG/MSSR bindings
ARM: shmobile: rcar-gen2: Obtain jump stub region from DT
ARM: debug-ll: Add support for r8a7743
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix deadlock in regulator quirk for R-Car Gen 2 SoCs
The da9063/da9210 regulator quirk for R-Car Gen2 boards uses a bus
notifier, and unregisters the notifier when it is no longer needed.
However, a notifier must not be unregistered from within the call chain.
This bug went unnoticed, as blocking_notifier_chain_unregister() didn't
take the semaphore during early boot. This is no longer the case as of
upstream commit 1c3c5eab17 ("sched/core: Enable might_sleep() and
smp_processor_id() checks early") and a deadlock occurs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=N5ig
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes3-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Third Round of Renesas ARM Based SoC Fixes for v4.13" from Simon Horman:
Fix deadlock in regulator quirk for R-Car Gen 2 SoCs
The da9063/da9210 regulator quirk for R-Car Gen2 boards uses a bus
notifier, and unregisters the notifier when it is no longer needed.
However, a notifier must not be unregistered from within the call chain.
This bug went unnoticed, as blocking_notifier_chain_unregister() didn't
take the semaphore during early boot. This is no longer the case as of
upstream commit 1c3c5eab17 ("sched/core: Enable might_sleep() and
smp_processor_id() checks early") and a deadlock occurs.
* tag 'renesas-fixes3-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: rcar-gen2: Fix deadlock in regulator quirk
Simon Horman reported that Koelsch and Lager hang during boot, and
bisected this to commit 1c3c5eab17 ("sched/core: Enable
might_sleep() and smp_processor_id() checks early").
The da9063/da9210 regulator quirk for R-Car Gen2 boards uses a bus
notifier, and unregisters the notifier when it is no longer needed.
However, a notifier must not be unregistered from within the call chain.
This bug went unnoticed, as blocking_notifier_chain_unregister() didn't
take the semaphore during early boot. The aforementioned commit changed
that behavior, leading to a deadlock.
Fix this by removing the call to bus_unregister_notifier(), and keeping
local completion state instead.
Reported-by: Simon Horman <horms+renesas@verge.net.au>
Fixes: 663fbb5215 ("ARM: shmobile: R-Car Gen2: Add da9063/da9210 regulator quirk")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The migration from ARCH_SHMOBILE_MULTI to ARCH_RENESAS has been
completed in v4.12 by commit 9ed2d4bc5c ("ARM: dts: renesas:
Switch from ARCH_SHMOBILE_MULTI to ARCH_RENESAS"), so the
ARCH_SHMOBILE_MULTI symbol can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to the datasheet, the frequency of the ARM architecture timer
on RZ/G1E depends on the frequency of the ZS clock, just like on R-Car
E2 and V2H.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When using the new CPG/MSSR bindings, there is no longer a
"renesas,rcar-gen2-cpg-clocks" node, and the code to obtain the external
clock crystal frequency falls back to a default of 20 MHz.
While this is correct for all upstream R-Car Gen2 and RZ/G1 boards, this
is not necessarily the case for out-of-tree third party boards.
Add support for finding the external clock crystal oscillator on RZ/G1M,
and on R-Car H2, M2-W, and M2-N using the new CPG/MSSR bindings, through
the corresponding "renesas,r8a77xx-cpg-mssr" nodes.
Note that this is not needed on R-Car V2H and E2, and on RZ/G1E, as on
those SoCs the arch_timer and generic counter clock is derived from the
ZS clock instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for obtaining from DT the SRAM region to store the jump stub
for CPU core bringup, according to the renesas,smp-sram DT bindings.
If no region is specified in DT, the code falls back to hardcoded ICRAM1
as before, to maintain backwards compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SoC platform changes (arch/arm/mach-*). This merge window, the bulk is
for a few platforms:
- Andres Färber adds initial support for the Actions Semi S500 (a.k.a.
'owl') platform, a close relative of the S900 platform he adds for arm64.
- in mach-omap2, we remove more legacy code
- Rockchips gains support for the RV1108 SoC designed for camera
applications.
- For Atmel, we gain support for MMU-less SoCs (SAME70/V71/S70/V70)
- Minor updates for other platforms, including davinci, s3c64xx,
prima2, stm32, broadcom nsp, amlogic, pxa, imx and renesas
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAWVo7+GCrR//JCVInAQKbMA//WeEPEDUt0boJCUfuzXfZ35S5ksBMBGQa
NaOJvcW3T//7Tfa88YlBEB7h1w22u1Sv4/CfcistdSPbUwZLyYo6aUz53AwlUnLs
bVHnd8+h1xN6qSDjzOPIEQQHg9OVIRBD49moBgJ1BkXzyqR/RI1jPPyyRl5vucSW
MYRxhPkplmjFL5+6uvFoSOdd3Z/FLoEYRrkIk4iu+KgKtnNlj4P1FNSdm6Yb29dj
yzmXoSpxEzbq0ahGlkjrekEJxTWvW1vOq9d+xTKwTbXoM7pbzXnBRzx4q2Fg9GAT
BJseMx+uDEG/+eYrFZA7jX/HgpKB1fAlCGp+dK6GIcJoEM6lFKJRsJrP702KPzg0
PqOMM/htq/4hZ7Waz+Yj3lyVF2C+A6Dn/fXPaHJGdTLj4r0OLgZayhBXFHp1VX2G
9ERx1UCnfxeY91VBUM99qo21ECT7j0C/bZLln8MFjwX8tk3OATkElIAtnsEHxJ5d
v4TEkI/AcpMW4lMj/u/hp1PJMCvhlSreWPGx1PRax6va+YB5Ov19DshVgyfoTTq9
kArUJWQdKo4aKqB+feg9NHNC01xSLw5ywKb+oIyYP3jZzMexzRyP5L7EAVOu6Cel
iHeIRpo8VjX63gltE+9u4aZ/aEMREGVcgkzuwBTKqbVQ3ismrmGYe54VnFAushJS
m+XSB250Vz8=
=8F3w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"SoC platform changes (arch/arm/mach-*). This merge window, the bulk is
for a few platforms:
- Andres Färber adds initial support for the Actions Semi S500 (aka
'owl') platform, a close relative of the S900 platform he adds for
arm64.
- in mach-omap2, we remove more legacy code
- Rockchips gains support for the RV1108 SoC designed for camera
applications.
- For Atmel, we gain support for MMU-less SoCs (SAME70/V71/S70/V70)
- Minor updates for other platforms, including davinci, s3c64xx,
prima2, stm32, broadcom nsp, amlogic, pxa, imx and renesas"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (74 commits)
ARM: owl: smp: Drop bogus holding pen
ARM: owl: Drop custom machine
ARM: owl: smp: Implement SPS power-gating for CPU2 and CPU3
soc: actions: owl-sps: Factor out owl_sps_set_pg() for power-gating
soc: actions: Add Owl SPS
dt-bindings: power: Add Owl SPS power domains
MAINTAINERS: Update Actions Semi section with SPS
ARM: owl: Implement CPU enable-method for S500
MAINTAINERS: Add Actions Semi Owl section
ARM: Prepare Actions Semi S500
ARM: socfpga: Increase max number of GPIOs
ARM: stm32: Introduce MACH_STM32F469 flag
ARM: prima2: remove redundant select CPU_V7
ARM: davinci: fix const warnings
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ALWAYS_ON
ARM: OMAP4: hwmod_data: add SHAM crypto accelerator
ARM: OMAP4: hwmod data: add des
ARM: OMAP4: hwmod data: add aes2
ARM: OMAP4: hwmod data: add aes1
ARM: pxa: Delete an error message for a failed memory allocation in pxa3xx_u2d_probe()
...
The function name is now renamed to 'timer_probe' for consistency with
the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Improve handling of always-on PM domains by using the
GENPD_FLAG_ALWAYS_ON flag introduced in commit ffaa42e8a4 ("PM /
Domains: Enable users of genpd to specify always on PM domains").
Note that the PM domain containing the serial console is still handled
locally.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Even though L2C is specified in the DT, you still need to add the aux
settings in the machine_desc.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Pull ARM updates from Russell King:
- nommu updates from Afzal Mohammed cleaning up the vectors support
- allow DMA memory "mapping" for nommu Benjamin Gaignard
- fixing a correctness issue with R_ARM_PREL31 relocations in the
module linker
- add strlen() prototype for the decompressor
- support for DEBUG_VIRTUAL from Florian Fainelli
- adjusting memory bounds after memory reservations have been
registered
- unipher cache handling updates from Masahiro Yamada
- initrd and Thumb Kconfig cleanups
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (23 commits)
ARM: mm: round the initrd reservation to page boundaries
ARM: mm: clean up initrd initialisation
ARM: mm: move initrd init code out of arm_memblock_init()
ARM: 8655/1: improve NOMMU definition of pgprot_*()
ARM: 8654/1: decompressor: add strlen prototype
ARM: 8652/1: cache-uniphier: clean up active way setup code
ARM: 8651/1: cache-uniphier: include <linux/errno.h> instead of <linux/types.h>
ARM: 8650/1: module: handle negative R_ARM_PREL31 addends correctly
ARM: 8649/2: nommu: remove Hivecs configuration is asm
ARM: 8648/2: nommu: display vectors base
ARM: 8647/2: nommu: dynamic exception base address setting
ARM: 8646/1: mmu: decouple VECTORS_BASE from Kconfig
ARM: 8644/1: Reduce "CPU: shutdown" message to debug level
ARM: 8641/1: treewide: Replace uses of virt_to_phys with __pa_symbol
ARM: 8640/1: Add support for CONFIG_DEBUG_VIRTUAL
ARM: 8639/1: Define KERNEL_START and KERNEL_END
ARM: 8638/1: mtd: lart: Rename partition defines to be prefixed with PART_
ARM: 8637/1: Adjust memory boundaries after reservations
ARM: 8636/1: Cleanup sanity_check_meminfo
ARM: add CPU_THUMB_CAPABLE to indicate possible Thumb support
...
All low-level PM/SMP code using virt_to_phys() should actually use
__pa_symbol() against kernel symbols. Update code where relevant to move
away from virt_to_phys().
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the SoC branch we normally collect classic arch/arm/mach-* contents, i.e.
C code changes for SoC platforms. This release cycle the diffstat is quite
nice, in that we're removing 3x the amount of code that's being added.
The main reason for this is that there's a removal of camera drivers for
Freescale i.MX chips (driver was removed so the device registration isn't
needed any more). There's also removal of display initialization code for OMAP
that is no longer needed.
The rest are mostly minor tweaks and cleanups; constification on Samsung
platforms, cleanup of ux500 platform data, purge of other unused platform
data/device seutp on i.MX and other good stuff.
New SoC support this cycle is for two Allwinner platforms, H2+ and V3s.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YE8v
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"In the SoC branch we normally collect classic arch/arm/mach-*
contents, i.e. C code changes for SoC platforms. This release cycle
the diffstat is quite nice, in that we're removing 3x the amount of
code that's being added.
The main reason for this is that there's a removal of camera drivers
for Freescale i.MX chips (driver was removed so the device
registration isn't needed any more). There's also removal of display
initialization code for OMAP that is no longer needed.
The rest are mostly minor tweaks and cleanups; constification on
Samsung platforms, cleanup of ux500 platform data, purge of other
unused platform data/device seutp on i.MX and other good stuff.
New SoC support this cycle is for two Allwinner platforms, H2+ and
V3s"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (55 commits)
ARM: ux500: remove deleted file from Makefile
ARM: ep93xx: Disable TS-72xx watchdog before uncompressing
ARM: ux500: cut some platform data
MAINTAINERS: Update for the current location of the bcm2835 tree.
ARM: davinci: remove BUG_ON() from da850_register_sata()
ARM: davinci: da850: model the SATA refclk
ARM: davinci: da850: add con_id for the SATA clock
ARM: davinci: da8xx-dt: add OF_DEV_AUXDATA entry for SATA
arm: mvebu: support for SMP on 98DX3336 SoC
dt-bindings: video: exynos7-decon: Remove obsolete samsung,power-domain property
soc: dove: constify reset_control_ops structures
ARM: mv78xx0: fix possible PCI buffer overflow
MAINTAINERS: transfer maintainership for the EZX platform
ARM: shmobile: rcar-gen2: Add more register documentation
ARM: tegra: paz00: Fix __initdata placement
ARM: OMAP: clock: Remove unused mpurate cmdline option
ARM: davinci: add skeleton for pdata-quirks
arm: sunxi: add support for V3s SoC
ARM: OMAP2+: omap_hwmod: Add support for earlycon
arm: hisi: drop extern hip01_cpu_die
...
This patch adds a OSTM driver for the Renesas architecture.
The OS Timer (OSTM) has independent channels that can be
used as a freerun or interval times.
This driver uses the first probed device as a clocksource
and then any additional devices as clock events.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
After
1. commit 9f5ce39ddb ("ARM: shmobile: rcar-gen2: Obtain extal
frequency from DT"),
2. commit 80951f04c3 ("ARM: shmobile: rcar-gen2: Stop passing
mode pins state to clock driver"),
3. and handling of debug resource reset,
there are no more users of rcar_gen2_read_mode_pins() left.
Remove the function and its support definitions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now debug resource reset is handled properly, allow booting secondary
CPU cores when hardware debug mode is enabled (MD21=1, SW8-4=OFF on
koelsch) on legacy r8a7791.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now debug resource reset is handled properly, allow booting secondary
CPU cores when hardware debug mode is enabled (MD21=1) on SoCs using the
"renesas,apmu" enable method.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In debug mode (MD21=1), reset requests derived from power-shutoff to the
AP-system CPU cores must be enabled before the AP-system CPU cores
resume from power-shutoff for the first time. Else resume may fail,
causing the system to hang during boot.
As setting these bits is a no-op in normal mode, there's no need to
check the actual state of MD21 first.
Inspired by CPU-specific patches in the BSP by Hisashi Nakamura
<hisashi.nakamura.ak@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Driver updates for ARM SoCs, including a couple of newly added drivers:
- A new driver for the power management controller on TI Keystone
- Support for the prerelease "SCPI" firmware protocol that ended up
being shipped by Amlogic in their GXBB SoC.
- A soc_device can now be matched using a glob from inside the
kernel, when another driver wants to know the specific chip
it is running on and cannot find out from DT, firmware or hardware.
- Renesas SoCs now support identification through the soc_device
interface, both in user space and kernel.
- Renesas r8a7743 and r8a7745 gain support for their system controller
- A new checking module for the ARM "PSCI" (not to be confused
with "SCPI" mentioned above) firmware interface.
- A new driver for the Tegra GMI memory interface
- Support for the Tegra firmware interfaces with their
power management controllers
As usual, the updates for the reset controller framework are merged
here, as they tend to touch multiple SoCs as well, including a new
driver for the Oxford (now Broadcom) OX820 chip and the Tegra
bpmp interface.
The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
Rockchips SoCs see some further updates.
Conflicts:
- ARCH_RENESAS now selects SOC_BUS, but no longer needs GPIOLIB
- drivers/soc/renesas/Makefile: multiple files got added, keep
all in logical sorting
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6dP8
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- A new driver for the power management controller on TI Keystone
- Support for the prerelease "SCPI" firmware protocol that ended up
being shipped by Amlogic in their GXBB SoC.
- A soc_device can now be matched using a glob from inside the
kernel, when another driver wants to know the specific chip it is
running on and cannot find out from DT, firmware or hardware.
- Renesas SoCs now support identification through the soc_device
interface, both in user space and kernel.
- Renesas r8a7743 and r8a7745 gain support for their system
controller
- A new checking module for the ARM "PSCI" (not to be confused with
"SCPI" mentioned above) firmware interface.
- A new driver for the Tegra GMI memory interface
- Support for the Tegra firmware interfaces with their power
management controllers
As usual, the updates for the reset controller framework are merged
here, as they tend to touch multiple SoCs as well, including a new
driver for the Oxford (now Broadcom) OX820 chip and the Tegra bpmp
interface.
The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
Rockchips SoCs see some further updates"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (76 commits)
misc: sram: remove useless #ifdef
drivers: psci: Allow PSCI node to be disabled
drivers: psci: PSCI checker module
soc: renesas: Identify SoC and register with the SoC bus
firmware: qcom: scm: Return PTR_ERR when devm_clk_get fails
firmware: qcom: scm: Remove core, iface and bus clocks dependency
dt-bindings: firmware: scm: Add MSM8996 DT bindings
memory: da8xx-ddrctl: drop the call to of_flat_dt_get_machine_name()
bus: da8xx-mstpri: drop the call to of_flat_dt_get_machine_name()
ARM: shmobile: Document DT bindings for Product Register
soc: renesas: rcar-sysc: add R8A7745 support
reset: Add Tegra BPMP reset driver
dt-bindings: firmware: Allow child nodes inside the Tegra BPMP
dt-bindings: Add power domains to Tegra BPMP firmware
firmware: tegra: Add BPMP support
firmware: tegra: Add IVC library
dt-bindings: firmware: Add bindings for Tegra BPMP
mailbox: tegra-hsp: Use after free in tegra_hsp_remove_doorbells()
mailbox: Add Tegra HSP driver
firmware: arm_scpi: add support for pre-v1.0 SCPI compatible
...
These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- Added support for the TI DRA71x family of SoCs in mach-omap2,
this is an new variant of the the DRA72x/DRA74x automotive
infotainment chips we already supported for a while.
- Added support for the ST STM32F746 SoC, the first Cortex-M7
based microcontroller we support, related to the smaller
STM32F4 family.
- Renesas adds support for r8a7743 and r8a7745 in mach-shmobile,
see http://elinux.org/RZ-G
- SMP is now supported on the OX820 platform
- A lot of code in mach-omap2 gets removed as a follow-up to
removing support for board files in the previous release
- Davinci has some new work to improve USB support
- For i.MX, the performance monitor now supports profiling the
memory controller using 'perf'
Conflicts:
arch/arm/mach-shmobile/setup-rcar-gen2.c: rcar_gen2_clocks_init()
is gone, calling of_clk_init(NULL) is sufficient now.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BF6Y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- Added support for the TI DRA71x family of SoCs in mach-omap2, this
is an new variant of the the DRA72x/DRA74x automotive infotainment
chips we already supported for a while.
- Added support for the ST STM32F746 SoC, the first Cortex-M7 based
microcontroller we support, related to the smaller STM32F4 family.
- Renesas adds support for r8a7743 and r8a7745 in mach-shmobile, see
http://elinux.org/RZ-G
- SMP is now supported on the OX820 platform
- A lot of code in mach-omap2 gets removed as a follow-up to removing
support for board files in the previous release
- Davinci has some new work to improve USB support
- For i.MX, the performance monitor now supports profiling the memory
controller using 'perf'"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (95 commits)
ARM: davinci: da830-evm: use gpio descriptor for mmc pins
ARM: davinci: da850-evm: use gpio descriptor for mmc pins
ARM: davinci: hawk: use gpio descriptor for mmc pins
ARM: ARTPEC-6: add select MFD_SYSCON to MACH_ARTPEC6
ARM: davinci: da8xx: Fix ohci device name
ARM: oxnas: Add OX820 config and makefile entry
ARM: oxnas: Add OX820 SMP support
ARM: davinci: PM: fix build when da850 not compiled in
ARM: orion5x: remove legacy support of ls-chl
ARM: integrator: drop EBI access use syscon
ARM: BCM5301X: Add back handler ignoring external imprecise aborts
ARM: davinci: PM: support da8xx DT platforms
ARM: davinci: PM: cleanup: remove references to pdata
ARM: davinci: PM: rework init, remove platform device
ARM: Kconfig: Introduce MACH_STM32F746 flag
ARM: mach-stm32: Add a new SOC - STM32F746
ARM: shmobile: document SK-RZG1E board
ARM: shmobile: r8a7745: basic SoC support
ARM: imx: mach-imx6ul: add imx6ull support
ARM: zynq: Reserve correct amount of non-DMA RAM
...
Identify the SoC type and revision, and register this information with
the SoC bus, so it is available under /sys/devices/soc0/, and can be
checked where needed using soc_device_match().
Identification is done using the Product Register or Common Chip Code
Register, as declared in DT (PRR only for now), or using a hardcoded
fallback if missing.
Example:
Detected Renesas R-Car Gen2 r8a7791 ES1.0
...
# cat /sys/devices/soc0/{machine,family,soc_id,revision}
Koelsch
R-Car Gen2
r8a7791
ES1.0
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add minimal support for the RZ/G1E (R8A7745) SoC.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now the R-Car Gen2 CPG clock driver obtains the state of the mode pins
from the R-Car RST driver, there's no longer a need to pass this state
explicitly. Hence we can just call of_clk_init() instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Now the R-Car H1 CPG clock driver obtains the state of the mode pins
from the R-Car RST driver, there's no longer a need to pass this state
explicitly. Hence we can just remove the .init_time() callback, the
generic ARM code will take care of calling of_clk_init() and
clocksource_probe().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Now the R-Car M1A CPG clock driver obtains the state of the mode pins
from the R-Car RST driver, there's no longer a need to pass this state
explicitly. Hence we can just remove the .init_time() callback, the
generic ARM code will take care of calling of_clk_init().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
The four SoCs use identical machine operations, consolidate them into
two machine definitions in a single file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add minimal support for the RZ/G1M (R8A7743) SoC.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The RZ/G1M (r8a7743) uses the R-Car Gen2 core, but not the R-Car Gen2 clock
driver. This is a harbinger of a transition for R-Car Gen2 SoCs. As the
process to get all the required pieces in place is somewhat complex it
seems useful to try to disentangle dependencies where possible.
The approach here is to temporarily disable calling rcar_gen2_clocks_init()
if no R-Car Gen2 SoC are configured and thus the symbol will not be
present.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort alphabetically all symbols selected by ARCH_RENESAS
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- We get support for running in big-endian mode on two platforms:
sunxi (Allwinner) and s3c24xx (old Samsung).
- The recently added Uniphier platform now uses standard PSCI
methods for SMP booting and we remove support for old bootloader
versions that did not support it yet.
- In sunxi, we gain support for the "Nextthing GR8" SoC, which
is a close relative of the Allwinner A13 and R8 chips.
- PXA completes its move over to the generic dmaengine framework
and removes its old private API
- mach-bcm gains support for BCM47189/BCM53573, their first ARM
SoC with integrated 802.11ac wireless networking.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=y4XF
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- We get support for running in big-endian mode on two platforms:
sunxi (Allwinner) and s3c24xx (old Samsung).
- The recently added Uniphier platform now uses standard PSCI methods
for SMP booting and we remove support for old bootloader versions
that did not support it yet.
- In sunxi, we gain support for the "Nextthing GR8" SoC, which is a
close relative of the Allwinner A13 and R8 chips.
- PXA completes its move over to the generic dmaengine framework and
removes its old private API
- mach-bcm gains support for BCM47189/BCM53573, their first ARM SoC
with integrated 802.11ac wireless networking"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: imx legacy: pca100: move peripheral initialization to .init_late
ARM: imx legacy: mx27ads: move peripheral initialization to .init_late
ARM: imx legacy: mx21ads: move peripheral initialization to .init_late
ARM: imx legacy: pcm043: move peripheral initialization to .init_late
ARM: imx legacy: mx35-3ds: move peripheral initialization to .init_late
ARM: imx legacy: mx27-3ds: move peripheral initialization to .init_late
ARM: imx legacy: imx27-visstrim-m10: move peripheral initialization to .init_late
ARM: imx legacy: vpr200: move peripheral initialization to .init_late
ARM: imx legacy: mx31moboard: move peripheral initialization to .init_late
ARM: imx legacy: armadillo5x0: move peripheral initialization to .init_late
ARM: imx legacy: qong: move peripheral initialization to .init_late
ARM: imx legacy: mx31-3ds: move peripheral initialization to .init_late
ARM: imx legacy: pcm037: move peripheral initialization to .init_late
ARM: imx legacy: mx31lilly: move peripheral initialization to .init_late
ARM: imx legacy: mx31ads: move peripheral initialization to .init_late
ARM: imx legacy: mx31lite: move peripheral initialization to .init_late
ARM: imx legacy: kzm: move peripheral initialization to .init_late
MAINTAINERS: update list of Oxnas maintainers
ARM: orion5x: remove extraneous NO_IRQ
ARM: orion: simplify orion_ge00_switch_init
...
The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion
of old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files.
If no regressions are found, another large cleanup for the platform
will happen as a follow-up, removing dead code and restructuring
the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now DT-only.
The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT
in principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress.
We can probably merge the remaining code into a single directory
in the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then.
Conflicts: two files deleted here have been modified upstream,
the changes can be discarded.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WaLy
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion of
old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files. If no regressions are found, another
large cleanup for the platform will happen as a follow-up, removing
dead code and restructuring the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now
DT-only. The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT in
principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress. We
can probably merge the remaining code into a single directory in
the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: select PCI_DOMAINS config from ARCH_MULTIPLATFORM
ARM: stop *MIGHT_HAVE_PCI* config from being selected redundantly
ARM: imx: (trivial) fix typo and grammar
ARM: clps711x: remove extraneous files
ARM: imx: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP2+: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP1: use IS_ENABLED() instead of checking for built-in or module
ARM: imx: remove platform-mxc_rnga
ARM: realview: imply device tree boot
ARM: realview: no need to select SMP_ON_UP explicitly
ARM: realview: delete the RealView board files
ARM: imx: no need to select SMP_ON_UP explicitly
ARM: i.MX: Move SOC_IMX1 into 'Device tree only'
ARM: i.MX: Remove i.MX1 non-DT support
ARM: i.MX: Remove i.MX1 Synertronixx SCB9328 board support
ARM: i.MX: Remove i.MX1 Armadeus APF9328 board support
ARM: mxs: remove obsolete startup code for TX28
ARM: i.MX31 iomux: remove duplicates with alternate name
ARM: i.MX31 iomux: remove plain duplicates
ARM: OMAP2+: Drop legacy board file for LDP
...
Pull CPU hotplug updates from Thomas Gleixner:
"Yet another batch of cpu hotplug core updates and conversions:
- Provide core infrastructure for multi instance drivers so the
drivers do not have to keep custom lists.
- Convert custom lists to the new infrastructure. The block-mq custom
list conversion comes through the block tree and makes the diffstat
tip over to more lines removed than added.
- Handle unbalanced hotplug enable/disable calls more gracefully.
- Remove the obsolete CPU_STARTING/DYING notifier support.
- Convert another batch of notifier users.
The relayfs changes which conflicted with the conversion have been
shipped to me by Andrew.
The remaining lot is targeted for 4.10 so that we finally can remove
the rest of the notifiers"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
cpufreq: Fix up conversion to hotplug state machine
blk/mq: Reserve hotplug states for block multiqueue
x86/apic/uv: Convert to hotplug state machine
s390/mm/pfault: Convert to hotplug state machine
mips/loongson/smp: Convert to hotplug state machine
mips/octeon/smp: Convert to hotplug state machine
fault-injection/cpu: Convert to hotplug state machine
padata: Convert to hotplug state machine
cpufreq: Convert to hotplug state machine
ACPI/processor: Convert to hotplug state machine
virtio scsi: Convert to hotplug state machine
oprofile/timer: Convert to hotplug state machine
block/softirq: Convert to hotplug state machine
lib/irq_poll: Convert to hotplug state machine
x86/microcode: Convert to hotplug state machine
sh/SH-X3 SMP: Convert to hotplug state machine
ia64/mca: Convert to hotplug state machine
ARM/OMAP/wakeupgen: Convert to hotplug state machine
ARM/shmobile: Convert to hotplug state machine
arm64/FP/SIMD: Convert to hotplug state machine
...
PCI_DOMAINS config should be selected for any SoCs
having more than a single PCIe controller. Without PCI_DOMAINS
config, only one PCIe controller gets registered.
Select PCI_DOMAINS in ARCH_MULTIPLATFORM if PCI is selected, since
it doesn't harm even if a platform has a single PCIe port.
Also remove PCI_DOMAINS being selected from other platform
specific configs.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fabrizio Castro