The __end_handlers marker was intended to mark down upto code that gets
called from exception prologs. But that hasn't kept pace with code
changes. Case in point, slb_miss_realmode being called from exception
prolog code but isn't below __end_handlers marker. So, __end_handlers
marker is as good as a comment but could be misleading at times if it
isn't in sync with the code, as is the case now. So, let us avoid this
confusion by having a better comment and removing __end_handlers marker
altogether.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some of the interrupt vectors on 64-bit POWER server processors are only
32 bytes long (8 instructions), which is not enough for the full
first-level interrupt handler. For these we need to branch to an
out-of-line (OOL) handler. But when we are running a relocatable kernel,
interrupt vectors till __end_interrupts marker are copied down to real
address 0x100. So, branching to labels (ie. OOL handlers) outside this
section must be handled differently (see LOAD_HANDLER()), considering
relocatable kernel, which would need at least 4 instructions.
However, branching from interrupt vector means that we corrupt the
CFAR (come-from address register) on POWER7 and later processors as
mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions)
that contains the part up to the point where the CFAR is saved in the
PACA should be part of the short interrupt vectors before we branch out
to OOL handlers.
But as mentioned already, there are interrupt vectors on 64-bit POWER
server processors that are only 32 bytes long (like vectors 0x4f00,
0x4f20, etc.), which cannot accomodate the above two cases at the same
time owing to space constraint. Currently, in these interrupt vectors,
we simply branch out to OOL handlers, without using LOAD_HANDLER(),
which leaves us vulnerable when running a relocatable kernel (eg. kdump
case). While this has been the case for sometime now and kdump is used
widely, we were fortunate not to see any problems so far, for three
reasons:
1. In almost all cases, production kernel (relocatable) is used for
kdump as well, which would mean that crashed kernel's OOL handler
would be at the same place where we end up branching to, from short
interrupt vector of kdump kernel.
2. Also, OOL handler was unlikely the reason for crash in almost all
the kdump scenarios, which meant we had a sane OOL handler from
crashed kernel that we branched to.
3. On most 64-bit POWER server processors, page size is large enough
that marking interrupt vector code as executable (see commit
429d2e83) leads to marking OOL handler code from crashed kernel,
that sits right below interrupt vector code from kdump kernel, as
executable as well.
Let us fix this by moving the __end_interrupts marker down past OOL
handlers to make sure that we also copy OOL handlers to real address
0x100 when running a relocatable kernel.
This fix has been tested successfully in kdump scenario, on an LPAR with
4K page size by using different default/production kernel and kdump
kernel.
Also tested by manually corrupting the OOL handlers in the first kernel
and then kdump'ing, and then causing the OOL handlers to fire - mpe.
Fixes: c1fb6816fb ("powerpc: Add relocation on exception vector handlers")
Cc: stable@vger.kernel.org
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have a bunch of SLB related code in the tree which is there to handle
dynamic VSIDs - but currently it's all disabled at compile time. The
comments say "Keep that around for when we re-implement dynamic VSIDs".
But that was over 10 years ago (commit 3c726f8dee ("[PATCH] ppc64:
support 64k pages")). The chance that it would still work unchanged is
minimal, and in the meantime it's confusing to folks browsing/grepping
the code. If we ever want to re-instate it, it's in the git history.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
The STD_EXCEPTION_PSERIES macro takes both a vector number, and a
location (memory address). However both are always identical, so combine
them to save repeating ourselves.
This does mean an exception handler must always exist at the location in
memory that matches its vector number. But that's OK because this is the
"STD" macro (standard), which does exactly that. We have other macros
for the other cases, eg. STD_EXCEPTION_PSERIES_OOL (out of line).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
HMT_MEDIUM_PPR_DISCARD is a macro which is present at the start of most
of our first level exception handlers. It conditionally executes a
HMT_MEDIUM instruction, which sets the processor priority to medium.
On on modern systems, ie. Power7 and later, it is nop'ed out at boot.
All it does is make the exception vectors more cramped, and consume 4
bytes of icache.
On old systems it has the effect of boosting the processor priority at
the start of exception processing. If we were previously in the idle
loop for example, we may be at low or very low priority. This is
desirable as we want to process the exception as fast as possible.
However looking closely at the generated code, we see that in all cases
we execute another HMT_MEDIUM just four instructions later. With code
patching applied, the final code on an old (Power6) system will look
like, eg:
c000000000000300 <data_access_pSeries>:
c000000000000300: 7c 42 13 78 mr r2,r2 <-
c000000000000304: 7d b2 43 a6 mtsprg 2,r13
c000000000000308: 7d b1 42 a6 mfsprg r13,1
c00000000000030c: f9 2d 00 80 std r9,128(r13)
c000000000000310: 60 00 00 00 nop
c000000000000314: 7c 42 13 78 mr r2,r2 <-
So I suggest that the added code complexity of HMT_MEDIUM_PPR_DISCARD is
not justified by the benefit of boosting the processor priority for the
duration of four instructions, and therefore we drop it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We should not expect pte bit position in asm code. Simply
by moving part of that to C
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, if HV KVM is configured but PR KVM isn't, we don't include
a test to see whether we were interrupted in KVM guest context for the
set of interrupts which get delivered directly to the guest by hardware
if they occur in the guest. This includes things like program
interrupts.
However, the recent bug where userspace could set the MSR for a VCPU
to have an illegal value in the TS field, and thus cause a TM Bad Thing
type of program interrupt on the hrfid that enters the guest, showed that
we can never be completely sure that these interrupts can never occur
in the guest entry/exit code. If one of these interrupts does happen
and we have HV KVM configured but not PR KVM, then we end up trying to
run the handler in the host with the MMU set to the guest MMU context,
which generally ends badly.
Thus, for robustness it is better to have the test in every interrupt
vector, so that if some way is found to trigger some interrupt in the
guest entry/exit path, we can handle it without immediately crashing
the host.
This means that the distinction between KVMTEST and KVMTEST_PR goes
away. Thus we delete KVMTEST_PR and associated macros and use KVMTEST
everywhere that we previously used either KVMTEST_PR or KVMTEST. It
also means that SOFTEN_TEST_HV_201 becomes the same as SOFTEN_TEST_PR,
so we deleted SOFTEN_TEST_HV_201 and use SOFTEN_TEST_PR instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We need to use a trampoline when using LOAD_HANDLER(), because the
destination needs to be in the first 64kB. An absolute branch has
no such limitations, so just jump there.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We had some code to restore the LR in the relocatable system call path
back when we used the LR to do an indirect branch.
Commit 6a404806df ("powerpc: Avoid link stack corruption in MMU
on syscall entry path") changed this to use the CTR which is volatile
across system calls so does not need restoring.
Remove the stale comment and the restore of the LR.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
commit id 2ba9f0d has changed CONFIG_KVM_BOOK3S_64_HV to tristate to allow
HV/PR bits to be built as modules. But the MCE code still depends on
CONFIG_KVM_BOOK3S_64_HV which is wrong. When user selects
CONFIG_KVM_BOOK3S_64_HV=m to build HV/PR bits as a separate module the
relevant MCE code gets excluded.
This patch fixes the MCE code to use CONFIG_KVM_BOOK3S_64_HANDLER. This
makes sure that the relevant MCE code is included when HV/PR bits
are built as a separate modules.
Fixes: 2ba9f0d887 ("kvm: powerpc: book3s: Support building HV and PR KVM as module")
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Winkle is a deep idle state supported in power8 chips. A core enters
winkle when all the threads of the core enter winkle. In this state
power supply to the entire chiplet i.e core, private L2 and private L3
is turned off. As a result it gives higher powersavings compared to
sleep.
But entering winkle results in a total hypervisor state loss. Hence the
hypervisor context has to be preserved before entering winkle and
restored upon wake up.
Power-on Reset Engine (PORE) is a dedicated engine which is responsible
for powering on the chiplet during wake up. It can be programmed to
restore the register contests of a few specific registers. This patch
uses PORE to restore register state wherever possible and uses stack to
save and restore rest of the necessary registers.
With hypervisor state restore things fall under three categories-
per-core state, per-subcore state and per-thread state. To manage this,
extend the infrastructure introduced for sleep. Mainly we add a paca
variable subcore_sibling_mask. Using this and the core_idle_state we can
distingush first thread in core and subcore.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Deep idle states like sleep and winkle are per core idle states. A core
enters these states only when all the threads enter either the
particular idle state or a deeper one. There are tasks like fastsleep
hardware bug workaround and hypervisor core state save which have to be
done only by the last thread of the core entering deep idle state and
similarly tasks like timebase resync, hypervisor core register restore
that have to be done only by the first thread waking up from these
state.
The current idle state management does not have a way to distinguish the
first/last thread of the core waking/entering idle states. Tasks like
timebase resync are done for all the threads. This is not only is
suboptimal, but can cause functionality issues when subcores and kvm is
involved.
This patch adds the necessary infrastructure to track idle states of
threads in a per-core structure. It uses this info to perform tasks like
fastsleep workaround and timebase resync only once per core.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Originally-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When a secondary hardware thread has finished running a KVM guest, we
currently put that thread into nap mode using a nap instruction in
the KVM code. This changes the code so that instead of doing a nap
instruction directly, we instead cause the call to power7_nap() that
put the thread into nap mode to return. The reason for doing this is
to avoid having the KVM code having to know what low-power mode to
put the thread into.
In the case of a secondary thread used to run a KVM guest, the thread
will be offline from the point of view of the host kernel, and the
relevant power7_nap() call is the one in pnv_smp_cpu_disable().
In this case we don't want to clear pending IPIs in the offline loop
in that function, since that might cause us to miss the wakeup for
the next time the thread needs to run a guest. To tell whether or
not to clear the interrupt, we use the SRR1 value returned from
power7_nap(), and check if it indicates an external interrupt. We
arrange that the return from power7_nap() when we have finished running
a guest returns 0, so pending interrupts don't get flushed in that
case.
Note that it is important a secondary thread that has finished
executing in the guest, or that didn't have a guest to run, should
not return to power7_nap's caller while the kvm_hstate.hwthread_req
flag in the PACA is non-zero, because the return from power7_nap
will reenable the MMU, and the MMU might still be in guest context.
In this situation we spin at low priority in real mode waiting for
hwthread_req to become zero.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
upatepp can get called for a nohpte fault when we find from the linux
page table that the translation was hashed before. In that case
we are sure that there is no existing translation, hence we could
avoid doing tlbie.
We could possibly race with a parallel fault filling the TLB. But
that should be ok because updatepp is only ever relaxing permissions.
We also look at linux pte permission bits when filling hash pte
permission bits. We also hold the linux pte busy bits while
inserting/updating a hashpte entry, hence a paralle update of
linux pte is not possible. On the other hand mprotect involves
ptep_modify_prot_start which cause a hpte invalidate and not updatepp.
Performance number:
We use randbox_access_bench written by Anton.
Kernel with THP disabled and smaller hash page table size.
86.60% random_access_b [kernel.kallsyms] [k] .native_hpte_updatepp
2.10% random_access_b random_access_bench [.] doit
1.99% random_access_b [kernel.kallsyms] [k] .do_raw_spin_lock
1.85% random_access_b [kernel.kallsyms] [k] .native_hpte_insert
1.26% random_access_b [kernel.kallsyms] [k] .native_flush_hash_range
1.18% random_access_b [kernel.kallsyms] [k] .__delay
0.69% random_access_b [kernel.kallsyms] [k] .native_hpte_remove
0.37% random_access_b [kernel.kallsyms] [k] .clear_user_page
0.34% random_access_b [kernel.kallsyms] [k] .__hash_page_64K
0.32% random_access_b [kernel.kallsyms] [k] fast_exception_return
0.30% random_access_b [kernel.kallsyms] [k] .hash_page_mm
With Fix:
27.54% random_access_b random_access_bench [.] doit
22.90% random_access_b [kernel.kallsyms] [k] .native_hpte_insert
5.76% random_access_b [kernel.kallsyms] [k] .native_hpte_remove
5.20% random_access_b [kernel.kallsyms] [k] fast_exception_return
5.12% random_access_b [kernel.kallsyms] [k] .__hash_page_64K
4.80% random_access_b [kernel.kallsyms] [k] .hash_page_mm
3.31% random_access_b [kernel.kallsyms] [k] data_access_common
1.84% random_access_b [kernel.kallsyms] [k] .trace_hardirqs_on_caller
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Cleanup OpalMCE_* definitions/declarations and other related code which
is not used anymore.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Benjamin Herrrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The system call FLIH (first-level interrupt handler) at 0xc00
unconditionally sets hardware priority to medium. For hypercalls, this
means we lose guest OS priority. The front end (do_kvm_0x**) to the
KVM interrupt handler always assumes that PPR priority is saved in
PACA exception save area, so it copies this to the kvm_hstate
structure. For hypercalls, this would be the saved priority from any
previous exception. Eventually, the guest gets resumed with an
incorrect priority.
The fix is to save the PPR priority in PACA exception save area before
switching HMT priorities in the FLIH so that existing code described above
in the KVM interrupt handler can copy it from there into the VCPU's saved
context.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
[mpe: Dropped HMT_MEDIUM_PPR_DISCARD and reworded comment]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In HMI interrupt handler we don't touch SRR0/SRR1, instead we touch
HSRR0/HSRR1. Hence we don't need to clear MSR_RI bit.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Once again, we see
arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:865: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:866: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:890: Error: attempt to move .org backwards
when compiling ppc:allmodconfig.
This time the problem has been caused by to commit 0869b6fd20
("powerpc/book3s: Add basic infrastructure to handle HMI in Linux"),
which adds functions hmi_exception_early and hmi_exception_after_realmode
into a critical (size-limited) code area, even though that does not appear
to be necessary.
Move those functions to a non-critical area of the file.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Handle Hypervisor Maintenance Interrupt (HMI) in Linux. This patch implements
basic infrastructure to handle HMI in Linux host. The design is to invoke
opal handle hmi in real mode for recovery and set irq_pending when we hit HMI.
During check_irq_replay pull opal hmi event and print hmi info on console.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
DISABLE_INTS has a long and storied history, but for some time now it
has not actually disabled interrupts.
For the open-coded exception handlers, just stop using it, instead call
RECONCILE_IRQ_STATE directly. This has the benefit of removing a level
of indirection, and making it clear that r10 & r11 are used at that
point.
For the addition case we still need a macro, so rename it to clarify
what it actually does.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At the moment the allmodconfig build is failing because we run out of
space between altivec_assist() at 0x5700 and the fwnmi_data_area at
0x7000.
Fixing it permanently will take some more work, but a quick fix is to
move bad_stack() below the fwnmi_data_area. That gives us just enough
room with everything enabled.
bad_stack() is called from the common exception handlers, but it's a
non-conditional branch, so we have plenty of scope to move it further
way.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Old cpus didn't have a Segment Lookaside Buffer (SLB), instead they had
a Segment Table (STAB). Now that we've dropped support for those cpus,
we can remove the STAB support entirely.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 2749a2f26a (powerpc/book3s: Fix machine check handling for
unhandled errors) introduced a few ABIv2 issues.
We can maintain ABIv1 and ABIv2 compatibility by branching to the
function rather than the dot symbol.
Fixes: 2749a2f26a ("powerpc/book3s: Fix machine check handling for unhandled errors")
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently machine check handler does not check for stack overflow for
nested machine check. If we hit another MCE while inside the machine check
handler repeatedly from same address then we get into risk of stack
overflow which can cause huge memory corruption. This patch limits the
nested MCE level to 4 and panic when we cross level 4.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Current code does not check for unhandled/unrecovered errors and return from
interrupt if it is recoverable exception which in-turn triggers same machine
check exception in a loop causing hypervisor to be unresponsive.
This patch fixes this situation and forces hypervisor to panic for
unhandled/unrecovered errors.
This patch also fixes another issue where unrecoverable_exception routine
was called in real mode in case of unrecoverable exception (MSR_RI = 0).
This causes another exception vector 0x300 (data access) during system crash
leading to confusion while debugging cause of the system crash.
Also turn ME bit off while going down, so that when another MCE is hit during
panic path, system will checkstop and hypervisor will get restarted cleanly
by SP.
With the above fixes we now throw correct console messages (see below) while
crashing the system in case of unhandled/unrecoverable machine checks.
--------------
Severe Machine check interrupt [[Not recovered]
Initiator: CPU
Error type: UE [Instruction fetch]
Effective address: 0000000030002864
Oops: Machine check, sig: 7 [#1]
SMP NR_CPUS=2048 NUMA PowerNV
Modules linked in: bork(O) bridge stp llc kvm [last unloaded: bork]
CPU: 36 PID: 55162 Comm: bash Tainted: G O 3.14.0mce #1
task: c000002d72d022d0 ti: c000000007ec0000 task.ti: c000002d72de4000
NIP: 0000000030002864 LR: 00000000300151a4 CTR: 000000003001518c
REGS: c000000007ec3d80 TRAP: 0200 Tainted: G O (3.14.0mce)
MSR: 9000000000041002 <SF,HV,ME,RI> CR: 28222848 XER: 20000000
CFAR: 0000000030002838 DAR: d0000000004d0000 DSISR: 00000000 SOFTE: 1
GPR00: 000000003001512c 0000000031f92cb0 0000000030078af0 0000000030002864
GPR04: d0000000004d0000 0000000000000000 0000000030002864 ffffffffffffffc9
GPR08: 0000000000000024 0000000030008af0 000000000000002c c00000000150e728
GPR12: 9000000000041002 0000000031f90000 0000000010142550 0000000040000000
GPR16: 0000000010143cdc 0000000000000000 00000000101306fc 00000000101424dc
GPR20: 00000000101424e0 000000001013c6f0 0000000000000000 0000000000000000
GPR24: 0000000010143ce0 00000000100f6440 c000002d72de7e00 c000002d72860250
GPR28: c000002d72860240 c000002d72ac0038 0000000000000008 0000000000040000
NIP [0000000030002864] 0x30002864
LR [00000000300151a4] 0x300151a4
Call Trace:
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
---[ end trace 7285f0beac1e29d3 ]---
Sending IPI to other CPUs
IPI complete
OPAL V3 detected !
--------------
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
STD_EXCEPTION_COMMON, STD_EXCEPTION_COMMON_ASYNC and
MASKABLE_EXCEPTION branch to the handler, so we can remove
the explicit dot symbol and binutils will do the right thing.
Signed-off-by: Anton Blanchard <anton@samba.org>
We have a number of places where we load the text address of a local
function and indirectly branch to it in assembly. Since it is an
indirect branch binutils will not know to use the function text
address, so that trick wont work.
There is no need for these functions to have a function descriptor
so we can replace it with a label and remove the dot symbol.
Signed-off-by: Anton Blanchard <anton@samba.org>
binutils is smart enough to know that a branch to a function
descriptor is actually a branch to the functions text address.
Alan tells me that binutils has been doing this for 9 years.
Signed-off-by: Anton Blanchard <anton@samba.org>
In:
commit 742415d6b6
Author: Michael Neuling <mikey@neuling.org>
powerpc: Turn syscall handler into macros
We converted the syscall entry code onto macros, but in doing this we
introduced some cruft that's never run and should never have been added.
This removes that code.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc non-virtualized cpuidle from Ben Herrenschmidt:
"This is the branch I mentioned in my other pull request which contains
our improved cpuidle support for the "powernv" platform
(non-virtualized).
It adds support for the "fast sleep" feature of the processor which
provides higher power savings than our usual "nap" mode but at the
cost of losing the timers while asleep, and thus exploits the new
timer broadcast framework to work around that limitation.
It's based on a tip timer tree that you seem to have already merged"
* 'powernv-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
cpuidle/powernv: Parse device tree to setup idle states
cpuidle/powernv: Add "Fast-Sleep" CPU idle state
powerpc/powernv: Add OPAL call to resync timebase on wakeup
powerpc/powernv: Add context management for Fast Sleep
powerpc: Split timer_interrupt() into timer handling and interrupt handling routines
powerpc: Implement tick broadcast IPI as a fixed IPI message
powerpc: Free up the slot of PPC_MSG_CALL_FUNC_SINGLE IPI message
While checking powersaving mode in machine check handler at 0x200, we
clobber CFAR register. Fix it by saving and restoring it during beq/bgt.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During "Fast-sleep" and deeper power savings state, decrementer and
timebase could be stopped making it out of sync with rest
of the cores in the system.
Add a firmware call to request platform to resync timebase
using low level platform methods.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Before adding Fast-Sleep into the cpuidle framework, some low level
support needs to be added to enable it. This includes saving and
restoring of certain registers at entry and exit time of this state
respectively just like we do in the NAP idle state.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
[Changelog modified by Preeti U. Murthy <preeti@linux.vnet.ibm.com>]
Signed-off-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With recent machine check patch series changes, The exception vectors
starting from 0x4300 are now overflowing with allyesconfig. Fix that by
moving machine_check_common and machine_check_handle_early code out of
that region to make enough room for exception vector area.
Fixes this build error reportes by Stephen:
arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:958: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:959: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:983: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:984: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1003: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1013: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1014: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1015: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1016: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1017: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1018: Error: attempt to move .org backwards
[Moved the code further down as it introduced link errors due to too long
relative branches to the masked interrupts handlers from the exception
prologs. Also removed the useless feature section --BenH
]
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When machine check real mode handler can not continue into host kernel
in V mode, it returns from the interrupt and we loose MCE event which
never gets logged. In such a situation queue up the MCE event so that
we can log it later when we get back into host kernel with r1 pointing to
kernel stack e.g. during syscall exit.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We can get machine checks from any context. We need to make sure that
we handle all of them correctly. If we are coming from hypervisor user-space,
we can continue in host kernel in virtual mode to deliver the MC event.
If we got woken up from power-saving mode then we may come in with one of
the following state:
a. No state loss
b. Supervisor state loss
c. Hypervisor state loss
For (a) and (b), we go back to nap again. State (c) is fatal, keep spinning.
For all other context which we not sure of queue up the MCE event and return
from the interrupt.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move machine check entry point into Linux. So far we were dependent on
firmware to decode MCE error details and handover the high level info to OS.
This patch introduces early machine check routine that saves the MCE
information (srr1, srr0, dar and dsisr) to the emergency stack. We allocate
stack frame on emergency stack and set the r1 accordingly. This allows us to be
prepared to take another exception without loosing context. One thing to note
here that, if we get another machine check while ME bit is off then we risk a
checkstop. Hence we restrict ourselves to save only MCE information and
register saved on PACA_EXMC save are before we turn the ME bit on. We use
paca->in_mce flag to differentiate between first entry and nested machine check
entry which helps proper use of emergency stack. We increment paca->in_mce
every time we enter in early machine check handler and decrement it while
leaving. When we enter machine check early handler first time (paca->in_mce ==
0), we are sure nobody is using MC emergency stack and allocate a stack frame
at the start of the emergency stack. During subsequent entry (paca->in_mce >
0), we know that r1 points inside emergency stack and we allocate separate
stack frame accordingly. This prevents us from clobbering MCE information
during nested machine checks.
The early machine check handler changes are placed under CPU_FTR_HVMODE
section. This makes sure that the early machine check handler will get executed
only in hypervisor kernel.
This is the code flow:
Machine Check Interrupt
|
V
0x200 vector ME=0, IR=0, DR=0
|
V
+-----------------------------------------------+
|machine_check_pSeries_early: | ME=0, IR=0, DR=0
| Alloc frame on emergency stack |
| Save srr1, srr0, dar and dsisr on stack |
+-----------------------------------------------+
|
(ME=1, IR=0, DR=0, RFID)
|
V
machine_check_handle_early ME=1, IR=0, DR=0
|
V
+-----------------------------------------------+
| machine_check_early (r3=pt_regs) | ME=1, IR=0, DR=0
| Things to do: (in next patches) |
| Flush SLB for SLB errors |
| Flush TLB for TLB errors |
| Decode and save MCE info |
+-----------------------------------------------+
|
(Fall through existing exception handler routine.)
|
V
machine_check_pSerie ME=1, IR=0, DR=0
|
(ME=1, IR=1, DR=1, RFID)
|
V
machine_check_common ME=1, IR=1, DR=1
.
.
.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch add a new callback kvmppc_ops. This will help us in enabling
both HV and PR KVM together in the same kernel. The actual change to
enable them together is done in the later patch in the series.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[agraf: squash in booke changes]
Signed-off-by: Alexander Graf <agraf@suse.de>
With later patches supporting PR kvm as a kernel module, the changes
that has to be built into the main kernel binary to enable PR KVM module
is now selected via KVM_BOOK3S_PR_POSSIBLE
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Both PR and HV KVM have separate, identical copies of the
kvmppc_skip_interrupt and kvmppc_skip_Hinterrupt handlers that are
used for the situation where an interrupt happens when loading the
instruction that caused an exit from the guest. To eliminate this
duplication and make it easier to compile in both PR and HV KVM,
this moves this code to arch/powerpc/kernel/exceptions-64s.S along
with other kernel interrupt handler code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This makes back traces and profiles easier to read.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The symbols that name some of our exception trampolines are ahead of the
location they name. In most cases this is OK because the code is tightly
packed, but in some cases it means the symbol floats ahead of the
correct location, eg:
c000000000000ea0 <performance_monitor_pSeries_1>:
...
c000000000000f00: 7d b2 43 a6 mtsprg 2,r13
Fix them all by moving the symbol after the set of the location.
While we're moving them anyway, rename them to loose the camelcase and
to make it clear that they are trampolines.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The denormalized exception handler (denorm_exception_hv) has a couple
of bugs. If the CONFIG_PPC_DENORMALISATION option is not selected,
or the HSRR1_DENORM bit is not set in HSRR1, we don't test whether the
interrupt occurred within a KVM guest. On the other hand, if the
HSRR1_DENORM bit is set and CONFIG_PPC_DENORMALISATION is enabled,
we corrupt the CFAR and PPR.
To correct these problems, this replaces the open-coded version of
EXCEPTION_PROLOG_1 that is there currently, and that is missing the
saving of PPR and CFAR values to the PACA, with an instance of
EXCEPTION_PROLOG_1. This adds an explicit KVMTEST after testing
whether the exception is one we can handle, and adds code to restore
the CFAR on exit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently if we take hypervisor facility unavaliable (from 0xf80/0x4f80) we
mark it as an OS facility unavaliable (0xf60) as the two share the same code
path.
The becomes a problem in facility_unavailable_exception() as we aren't able to
see the hypervisor facility unavailable exceptions.
Below fixes this by duplication the required macros.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJR0K2gAAoJEHm+PkMAQRiGWsEH+gMZSN1qRm34hZ82q1Tx7HvL
Eb/Gsl3Qw/7G2TlTqgjBUs36IdqV9O2cui/aa3/TfXvdvrx+0GlhRkEwQPc+ygcO
Mvoyoke4tT4+4jVFdCg1J8avREsa28/6oaHs0ZZxuVmJBBLTJH7aXaNsGn6eU1q9
9+p798MQis6naIiPC63somlZcCIiBhsuWCPWpEfLMn8G1HWAFTM3xXIbNBqe/brS
bmIOfhomlIZ5dcdaXGvjtP3+KJhkNDwhkPC4tVYu8JqqgSlrE+a+EGyEuuGqKk10
U+swiqyuD31uBI9ga54u/2FzSqDiAu6YOcMXevjo/m3g9XLdYbYLvN+nvN8alCQ=
=Ob6Z
-----END PGP SIGNATURE-----
Merge tag 'v3.10' into next
Merge 3.10 in order to get some of the last minute powerpc
changes, resolve conflicts and add additional fixes on top
of them.
Similar to the facility unavailble exception, except the facilities are
controlled by HFSCR.
Adapt the facility_unavailable_exception() so it can be called for
either the regular or Hypervisor facility unavailable exceptions.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The exception at 0xf60 is not the TM (Transactional Memory) unavailable
exception, it is the "Facility Unavailable Exception", rename it as
such.
Flesh out the handler to acknowledge the fact that it can be called for
many reasons, one of which is TM being unavailable.
Use STD_EXCEPTION_COMMON() for the exception body, for some reason we
had it open-coded, I've checked the generated code is identical.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
KVMTEST is a macro which checks whether we are taking an exception from
guest context, if so we branch out of line and eventually call into the
KVM code to handle the switch.
When running real guests on bare metal (HV KVM) the hardware ensures
that we never take a relocation on exception when transitioning from
guest to host. For PR KVM we disable relocation on exceptions ourself in
kvmppc_core_init_vm(), as of commit a413f47 "Disable relocation on
exceptions whenever PR KVM is active".
So convert all the RELON macros to use NOTEST, and drop the remaining
KVM_HANDLER() definitions we have for 0xe40 and 0xe80.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Hari Bathini