The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
We should be allocating enough information for a tiadc_device struct
which is about 400 bytes but instead we allocate enough for a second
iio_dev struct which is over 2000 bytes.
Fixes: fea89e2dfc ("iio: adc: ti_am335x_adc: use variable names for sizeof() operator")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The tiadc_irq_h(int irq, void *private) function is handling FIFO
overruns by clearing flags, disabling and enabling the ADC to
recover.
If the ADC is running in continuous mode a FIFO overrun happens
regularly. If the disabling of the ADC happens concurrently with
a new conversion. It might happen that the enabling of the ADC
is ignored by the hardware. This stops the ADC permanently. No
more interrupts are triggered.
According to the AM335x Reference Manual (SPRUH73H October 2011 -
Revised April 2013 - Chapter 12.4 and 12.5) it is necessary to
check the ADC FSM bits in REG_ADCFSM before enabling the ADC
again. Because the disabling of the ADC is done right after the
current conversion has been finished.
To trigger this bug it is necessary to run the ADC in continuous
mode. The ADC values of all channels need to be read in an endless
loop. The bug appears within the first 6 hours (~5.4 million
handled FIFO overruns). The user space application will hang on
reading new values from the character device.
Fixes: ca9a563805 ("iio: ti_am335x_adc: Add continuous sampling
support")
Signed-off-by: Michael Engl <michael.engl@wjw-solutions.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds the required pieces to ti_am335x_adc driver for
DMA support
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Now that open delay and sample delay for each channel is configurable
via DT, the default IDLE_TIMEOUT value is not enough as this is
calculated based on hardcoded macros. This results in driver returning
EBUSY sometimes. Fix this by increasing the timeout
value based on maximum value possible to open delay and sample delays
for each channel.
Fixes: 5dc11e8106 ("iio: adc: ti_am335x_adc: make sample delay, open delay, averaging DT parameters")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It is possible that two or more ADC channels can be simultaneously
requested for raw samples, in which case there can be race in access to
FIFO data resulting in loss of samples.
If am335x_tsc_se_set_once() is called again from tiadc_read_raw(), when
ADC is still acquired to sample one of the channels, the second process
might be put into uninterruptible sleep state. Fix these issues, by
protecting FIFO access and channel configurations with a mutex. Since
tiadc_read_raw() might take anywhere between few microseconds to few
milliseconds to finish execution (depending on averaging and delay
values supplied via DT), its better to use mutex instead of spinlock.
Fixes: 7ca6740cd1 ("mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix the code formatting to use the kernel preferred style
of using the actual variables to determize the size using
the sizeof() operator.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Whilst this part has a hardware buffer, the identifcation that IIO cares
about is the userspace facing end. It this case we push individual elements
from the hardware fifo into the software interface (specifically a kfifo)
rather than providing direct reads through to a hardware buffer
(as we still do in the sca3000 for example).
Technically the original specification as a hardware buffer could be
considered wrong, but it didn't matter until the patch listed below.
Result is that any attempt to enable the buffer will return -EINVAL
Fixes: 225d59adf1 ("iio: Specify supported modes for buffers")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add optional DT properties to set open delay, sample delay and number
of averages per sample for each adc step. Open delay, sample delay
and averaging are some of the parameters that affect the sampling rate
and accuracy of the sample. Making these parameters configurable via
DT will help in balancing speed vs accuracy.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Refactor DT parsing into a separate function from probe() to
help addition of more DT parameters later.
No functional changes.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If the in-kernel push interface is used we may have a different masks
on the device buffer and the kernel buffer and in this case the device
should generate data for the reunion of the buffers, which is
available at indio_dev->active_scan_mask.
Compiled tested only except for bmc150-accel which was tested at
runtime with the hardware.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Here's the big staging driver tree update for 3.20-rc1. Lots of little
things in here, adding up to lots of overall cleanups. The IIO driver
updates are also in here as they cross the staging tree boundry a lot.
I2O has moved into staging as well, as a plan to drop it from the tree
eventually as that's a dead subsystem.
All of this has been in linux-next with no reported issues for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtVQACgkQMUfUDdst+yk4mACgshYZ1fOQDoPR+BXd+QD1HXfh
GosAoICXkSjDQjwVo13W6QHIVMsUezY+
=4jHr
-----END PGP SIGNATURE-----
Merge tag 'staging-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging drivers patches from Greg KH:
"Here's the big staging driver tree update for 3.20-rc1.
Lots of little things in here, adding up to lots of overall cleanups.
The IIO driver updates are also in here as they cross the staging tree
boundry a lot. I2O has moved into staging as well, as a plan to drop
it from the tree eventually as that's a dead subsystem.
All of this has been in linux-next with no reported issues for a
while"
* tag 'staging-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (740 commits)
staging: lustre: lustre: libcfs: define symbols as static
staging: rtl8712: Do coding style cleanup
staging: lustre: make obd_updatemax_lock static
staging: rtl8188eu: core: switch with redundant cases
staging: rtl8188eu: odm: conditional setting with no effect
staging: rtl8188eu: odm: condition with no effect
staging: ft1000: fix braces warning
staging: sm7xxfb: fix remaining CamelCase
staging: sm7xxfb: fix CamelCase
staging: rtl8723au: multiple condition with no effect - if identical to else
staging: sm7xxfb: make smtc_scr_info static
staging/lustre/mdc: Initialize req in mdc_enqueue for !it case
staging/lustre/clio: Do not allow group locks with gid 0
staging/lustre/llite: don't add to page cache upon failure
staging/lustre/llite: Add exception entry check after radix_tree
staging/lustre/libcfs: protect kkuc_groups from write access
staging/lustre/fld: refer to MDT0 for fld lookup in some cases
staging/lustre/llite: Solve a race to access lli_has_smd in read case
staging/lustre/ptlrpc: hold rq_lock when modify rq_flags
staging/lustre/lnet: portal spreading rotor should be unsigned
...
This patch makes the initial changes required to workaround TSC-false
pen-up interrupts. It is required to implement these changes in order to
remove udelay in the TSC interrupt handler and false pen-up events. The
charge step is to be executed immediately after sampling X+. Hence TSC is
made to use higher numbered steps (steps 5 to 16 for 5 co-ordinate
readouts, 4 wire TSC configuration) and ADC to use lower ones. Further X
co-ordinate readouts must be the last to be sampled, thus co-ordinates are
sampled in the order Y-Z-X.
Signed-off-by: Brad Griffis <bgriffis@ti.com>
[vigneshr@ti.com: Ported the patch from v3.12 to v3.19rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
indio_dev was unused in function body plus some small style fix - add new
lines after "if(sth) return sth" and before the last return statement.
The argument was removed also in its client.
Signed-off-by: Karol Wrona <k.wrona@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Originally device and buffer registration were kept as separate operations
in IIO to allow to register two distinct sets of channels for buffered and
non-buffered operations. This has since already been further restricted and
the channel set registered for the buffer needs to be a subset of the
channel set registered for the device. Additionally the possibility to not
have a raw (or processed) attribute for a channel which was registered for
the device was added a while ago. This means it is possible to not register
any device level attributes for a channel even if it is registered for the
device. Also if a channel's scan_index is set to -1 and the channel is
registered for the buffer it is ignored.
So in summary it means it is possible to register the same channel array for
both the device and the buffer yet still end up with distinctive sets of
channels for both of them. This makes the argument for having to have to
manually register the channels for both the device and the buffer invalid.
Considering that the vast majority of all drivers want to register the same
set of channels for both the buffer and the device it makes sense to move
the buffer registration into the core to avoid some boiler-plate code in the
device driver setup path.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch removes the .owner field for drivers which use the
platform_driver_register api because this is overriden in
_platform_driver_register.
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since AI lines could be selected at will (linux-3.11) the sending
and receiving ends of the FIFO does not agree about what step is used
for a line. It only works if the last lines are used, like 5,6,7,
and fails if ie 2,4,6 is selected in DT.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Tested-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: stable@vger.kernel.org
New drivers:
* si7005 relative humidity and temperature sensor
* Lite-on ltr501 ambient light and proximity sensor
Cleanups
* Clean up some dead comments in max1363
* Drop some obsolete variables in adjd_s311 and tcs3472 left over from
the introduction of iio_push_to_buffers_with_timestamp.
* Drop some unneeded linux/init.h includes
* Squish a sparse warning in mpl3115 by correctly specifying a be32 variable.
* A number of cleanups and fixes for sca3000
* Drop an unneed checks in mxs-lradc, ad7303 and adis16400.
* Drop a platform_set_drvdata in viperboard after the only use of it was
removed during a devm conversion.
* Add a missing device name for ak8975 to comply with the ABI.
* Put mpu6050 into the IMU menu as it slipped out into the main menu.
* Fix a typo and some comment formatting in mpu6050.
* Document at91 ADC clock properties.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=nSiE
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new drivers and cleanups for IIO in the 3.15 cycle.
New drivers:
* si7005 relative humidity and temperature sensor
* Lite-on ltr501 ambient light and proximity sensor
Cleanups
* Clean up some dead comments in max1363
* Drop some obsolete variables in adjd_s311 and tcs3472 left over from
the introduction of iio_push_to_buffers_with_timestamp.
* Drop some unneeded linux/init.h includes
* Squish a sparse warning in mpl3115 by correctly specifying a be32 variable.
* A number of cleanups and fixes for sca3000
* Drop an unneed checks in mxs-lradc, ad7303 and adis16400.
* Drop a platform_set_drvdata in viperboard after the only use of it was
removed during a devm conversion.
* Add a missing device name for ak8975 to comply with the ABI.
* Put mpu6050 into the IMU menu as it slipped out into the main menu.
* Fix a typo and some comment formatting in mpu6050.
* Document at91 ADC clock properties.
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ADC driver always programs all possible ADC values and discards
them except for the value IIO asked for. On the am335x-evm the driver
programs four values and it takes 500us to gather them. Reducing the number
of conversations down to the (required) one also reduces the busy loop down
to 125us.
This leads to another error, namely the FIFOCOUNT register is sometimes
(like one out of 10 attempts) not updated in time leading to EBUSY.
The next read has the FIFOCOUNT register updated.
Checking for the ADCSTAT register for being idle isn't a good choice either.
The problem is that if TSC is used at the same time, the HW completes the
conversation for ADC *and* before the driver noticed it, the HW begins to
perform a TSC conversation and so the driver never seen the HW idle. The
next time we would have two values in the FIFO but since the driver reads
everything we always see the current one.
So instead of polling for the IDLE bit in ADCStatus register, we should
check the FIFOCOUNT register. It should be one instead of zero because we
request one value.
This change in turn leads to another error. Sometimes if TSC & ADC are
used together the TSC starts generating interrupts even if nobody
actually touched the touchscreen. The interrupts seem valid because TSC's
FIFO is filled with values for each channel of the TSC. This condition stops
after a few ADC reads but will occur again. Not good.
On top of this (even without the changes I just mentioned) there is a ADC
& TSC lockup condition which was reported to me by Jeff Lance including the
following test case:
A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw"
and a mug on touch screen. With this setup, the hardware will lockup after
something between 20 minutes and it could take up to a couple of hours.
During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means
STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is
idle and busy at the same time which is an invalid condition.
For all this reasons I decided to rework this TSC/ADC part and add a
handshake / synchronization here:
First the ADC signals that it needs the HW and writes a 0 mask into the
SE register. The HW (if active) will complete the current conversation
and become idle. The TSC driver will gather the values from the FIFO
(woken up by an interrupt) and won't "enable" another conversation.
Instead it will wake up the ADC driver which is already waiting. The ADC
driver will start "its" conversation and once it is done, it will
enable the TSC steps so the TSC will work again.
After this rework I haven't observed the lockup so far. Plus the busy
loop has been reduced from 500us to 125us.
The continues-read mode remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The update of the SE register in MFD doesn't look right as it has
nothing to do with it. The better place to do it is in TSC driver (which
is already doing it) and in the ADC driver which needs this only in the
continues mode.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The purpose of reg_se_cache has been defeated. It should avoid the
read-back of the register to avoid the latency and the fact that the
bits are reset to 0 after the individual conversation took place.
The reason why this is required like this to work, is that read-back of
the register removes the bits of the ADC so they do not start another
conversation after the register is re-written from the TSC side for the
update.
To avoid the not required read-back I introduce a "set once" variant which
does not update the cache mask. After the conversation completes, the
bit is removed from the SE register anyway and we don't plan a new
conversation "any time soon". The current set function is renamed to
set_cache to distinguish the two operations.
This is a small preparation for a larger sync-rework.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It somehow looks like the ending bracket belongs to the if statement but
it does belong to the while loop. This patch moves the bracket where it
belongs.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver is missing the iio_buffer_attach() call. As such it will attempt
to free the buffer twice on removal.
Introduced in commit 9e69c9 ("iio: Add reference counting for buffers").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
ti_adc_dt_ids is always compiled in. Hence of_match_ptr is not
needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The equivalent of iio_sw_buffer_preenable() is now done in the IIO buffer
core, so there is no need to do this from the driver anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver is functional without this error case. Cleaned up.
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Trigger related headers and variables are not needed
as driver is now based on INDIO_BUFFER_HARDWARE mode
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Static is missing in function header. Corrected.
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Previously the driver had only one-shot reading functionality.
This patch adds continuous sampling support to the driver.
Continuous sampling starts when buffer is enabled.
HW IRQ wakes worker thread that pushes samples to userspace.
Sampling stops when buffer is disabled by userspace.
Patil Rachna (TI) laid the ground work for ADC HW register access.
Russ Dill (TI) fixed bugs in the driver relevant to FIFOs and IRQs.
I fixed channel scanning so multiple ADC channels can be read
simultaneously and pushed to userspace.
Restructured the driver to fit IIO ABI.
And added INDIO_BUFFER_HARDWARE mode.
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
12 bit ADC data is stored in 32 bits of storage.
Change from u32 to u16 to reduce wasted memory.
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Previously we tried to read data form ADC even before ADC sequencer
finished sampling. This led to wrong samples.
We now wait on ADC status register idle bit to be set.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This set is larger than I would like, partly due to my lack of review
time in the weeks before the merge window and partly because a
couple of large drivers and the subsystem as a whole seem to be
getting a lot more exposure and testing recently.
1) A long term bug in trigger handling gave a double free of the device.
2) Wrong return value handling means offsets are ignored in
iio_convert_raw_to_processed_unlocked.
3) The iio_channel_has_info utility function was incorrectly updated
during the recent info_mask split, this is now fixed.
4) mxs-lradc has a couple of little fixes.
5) A couple of missing .driver_module entries meant that drivers
could be removed from underneath their users.
6) Error path fixes for ad7303 and lis3l02dq.
7) The scale value for presure in the lps331ap driver was out by
a factor of 100.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)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=ratf
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.11a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
The first round of IIO fixes for the 3.11 cycle.
This set is larger than I would like, partly due to my lack of review
time in the weeks before the merge window and partly because a
couple of large drivers and the subsystem as a whole seem to be
getting a lot more exposure and testing recently.
1) A long term bug in trigger handling gave a double free of the device.
2) Wrong return value handling means offsets are ignored in
iio_convert_raw_to_processed_unlocked.
3) The iio_channel_has_info utility function was incorrectly updated
during the recent info_mask split, this is now fixed.
4) mxs-lradc has a couple of little fixes.
5) A couple of missing .driver_module entries meant that drivers
could be removed from underneath their users.
6) Error path fixes for ad7303 and lis3l02dq.
7) The scale value for presure in the lps331ap driver was out by
a factor of 100.
Add missing .driver_module of struct iio_info. This prevents the
module from being removed from underneath its users.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Usually we get all the values we wanted but it is possible, that te ADC
unit is busy performing the conversation for the HW events. In that case
-EBUSY is returned and the user may re-call the function.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The TSC part allows to specify the input lines. The IIO part assumes
that it usues always the last few, that means if IIO has adc-channels
set to 2 it will use channel 6 and 7. However it might make sense to use
only 6.
This patch changes the device property (which was introduced recently
and was never in an official release) in a way that the user can specify
which of the AIN lines should be used. In Addition to this, the name is
now AINx where x is the channel number i.e. for AIN6 we would have 6.
Prior this, it always started counting at 0 which is confusing. In
addition to this, it also checks for correct step number during reading
and does not rely on proper FIFO depth.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The driver programs a threshold of "coordinate_readouts" say 5. The
REG_FIFO0THR registers says it should it be programmed to "threshold
minus one". The driver does not expect just 5 coordinates but 5 * 2 + 2.
Multiplied by two because 5 for X and 5 for Y and plus 2 because we have
two Z.
The whole thing kind of works because It reads the 5 coordinates for X
and Y from FIFO0 and FIFO1 and the last element in each FIFO is ignored
within the loop and read later.
Nothing guaranties that FIFO1 is ready by the time it is read. In fact I
could see that that FIFO1 reaturns for Y channels 8,9, 10, 12, 6 and for
Y channel 7 for Z. The problem is that channel 7 and channel 12 got
somehow mixed up.
The other Problem is that FIFO1 is also used by the IIO part leading to
wrong results if both (tsc & adc) are used.
The patch tries to clean up the whole thing a little:
- Remove the +1 and -1 in REG_STEPCONFIG, REG_STEPDELAY and its counter
part in the for loop. This is just confusing.
- Use only FIFO0 in TSC. The fifo has space for 64 entries so should be
fine.
- Read the whole FIFO in one function and check the channel.
- in case we dawdle around, make sure we only read a multiple of our
coordinate set. On the second interrupt we will cleanup the remaining
enties.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
TI-adc reads a little better compared to tiadc. And if we add am335x to
it then we have the same naming scheme as the tsc side.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
This patch provides the members "datasheet_name" and scan_type. This is
the remaining part of the earlier patch where I (bigeasy) removed iio_map
because it is now supplied by the device tree. It also static names as
suggested by Jonathan.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
This patch removes access to platform data mfd_tscadc_board because the
platform is DT only.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Add DT support for client ADC driver.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Current code has hard coded value written to
step enable bits. Now the bits are updated based
on how many steps are needed to be configured got
from platform data.
The user needs to take care not to exceed
the count more than 16. While using ADC and TSC
one should take care to set this parameter correctly.
Sebastian added the common lock and moved the code, that manipulates the
steps, from into the mfd module.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The mfd driver creates platform data for the child devices and it is the
ti_tscadc_dev struct. This struct is copied for the two devices.
The copy of the structure makes a common lock in this structure a little
less usefull. Therefore the platform data is not a pointer to the
structure and the same structure is used.
While doing the change I noticed that the suspend/resume code assumes
the wrong pointer for ti_tscadc_dev and this has been fixed as well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
cc: Patil, Rachna <rachna@ti.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, and __devexit
from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for TI's ADC driver.
This is a multifunctional device.
Analog input lines are provided on which
voltage measurements can be carried out.
You can have upto 8 input lines.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Jonathan Cameron