It helps to cast struct uart_port to struct uart_8250_port at runtime.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This Multi-IO card has one serial 16550-like and one parallel port connector.
Here's the lspci output, after this commit is applied:
03:07.0 Serial controller: Device 4348:5053 (rev 10) (prog-if 02 [16550])
Subsystem: Device 4348:5053
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at cf00 [size=8]
Region 1: I/O ports at ce00 [size=8]
Kernel driver in use: parport_serial
Kernel modules: 8250_pci, parport_serial
This commit adds an entry with the device ID to the blacklist declared in
8250_pci to prevent the driver from taking ownership. Also, and as was done
for the 2S/1P variant, add a quirk to skip autodetection and set the correct
type to 16550A clone.
Proper entries are added to parport_serial, to support the device parallel
and serial ports.
Cc: Gianluca Anzolin <gianluca@sottospazio.it>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support the following additional baud rates with 0% error:
500000, 1500000, 2500000, 3500000
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aparently 9865 uses standard BAR encoding scheme (unlike 99xx cards).
Current pci_netmos_9900_setup() uses wrong BAR indices for the 9865 PCI
device, function 2. Using standard BAR indices makes all 6 ports work
for me. Thus disable the NetMos 9900 quirk for NetMos 9865 pci device.
For the reference, here is the relevant part of lspci for my device:
02:07.0 Serial controller: MosChip Semiconductor Technology Ltd. PCI
9865 Multi-I/O Controller (prog-if 02 [16550])
Subsystem: Device a000:1000
Flags: bus master, medium devsel, latency 32, IRQ 17
I/O ports at ac00 [size=8]
Memory at fcfff000 (32-bit, non-prefetchable) [size=4K]
Memory at fcffe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [48] Power Management version 2
Kernel driver in use: serial
02:07.1 Serial controller: MosChip Semiconductor Technology Ltd. PCI
9865 Multi-I/O Controller (prog-if 02 [16550])
Subsystem: Device a000:1000
Flags: bus master, medium devsel, latency 32, IRQ 18
I/O ports at a800 [size=8]
Memory at fcffd000 (32-bit, non-prefetchable) [size=4K]
Memory at fcffc000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [48] Power Management version 2
Kernel driver in use: serial
02:07.2 Communication controller: MosChip Semiconductor Technology Ltd.
PCI 9865 Multi-I/O Controller
Subsystem: Device a000:3004
Flags: bus master, medium devsel, latency 32, IRQ 19
I/O ports at a400 [size=8]
I/O ports at a000 [size=8]
I/O ports at 9c00 [size=8]
I/O ports at 9800 [size=8]
Memory at fcffb000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [48] Power Management version 2
Kernel driver in use: serial
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.
Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for Fintek's 4, 8, and 12 port PCIE serial cards.
Thanks to Fintek for the sample devices, and the spec needed in order to
implement this.
Cc: Amanda Ying <amanda_ying@fintek.com.tw>
Cc: Felix Shih <felix_shih@fintek.com.tw>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the printk() calls to to dev_*() instead, to tie into the dynamic
debugging infrastructure.
Also change some "raw" printk() calls to dev_err() to provide a better
error message to userspace so it can properly identify the device and
not just have to guess.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel BayTrail has two HS-UARTs with 64 byte fifo, support
for DMA and support for 16750 compatible Auto Flow Control.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The quirks and PCI ID table entries for the original ADDI-DATA APCI-7800
(not the newer APCI-7800-3) use PCI_DEVICE_ID_ADDIDATA_APCI7800 from
<linux/pci_ids.h> but the device ID was actually assigned to ADDI-DATA
by Applied Micro Circuits Corporation (PCI_VENDOR_ID_AMCC). Replace it
locally with #define PCI_DEVICE_ID_AMCC_ADDIDATA_APCI7800.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI_VENDOR_ID_ADDIDATA_OLD has the same value (0x10e8) as
PCI_VENDOR_ID_AMCC in <linux/pci_ids.h>. The vender ID is actually
assigned to Applied Micro Circuits Corporation. The 8250_pci driver
uses PCI_VENDOR_ID_ADDIDATA_OLD in the lists of quirks and PCI IDs for
the ADDI-DATA APCI-7800 card. Change it to use the more accurate
PCI_VENDOR_ID_AMCC.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent regression about NetMos 9835 Multi-I/O boards indicates
that comment pointing to the parport_serial driver could be helpful.
Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8d2f8cd424.
As reported by Stefan, this device already works with the parport_serial
driver, so the 8250_pci driver should not also try to grab it as well.
Reported-by: Stefan Seyfried <stefan.seyfried@googlemail.com>
Cc: Wang YanQing <udknight@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in 8250.c for detecting ARM/XScale UARTs says:
* Try writing and reading the UART_IER_UUE bit (b6).
* If it works, this is probably one of the Xscale platform's
* internal UARTs.
If the above passes, it then goes on to:
* It's an Xscale.
* We'll leave the UART_IER_UUE bit set to 1 (enabled).
However, the CH352 uses the UART_IER_UUE as the LOWPOWER function,
so it is readable and writable. According to the datasheet:
"LOWPOWER:When the bit is 1, close the internal benchmark
clock of serial port to set into low-power status.
So it essentially gets mis-detected as Xscale, and gets
powered down in the process. The device in question where
this was seen is listed by lspci as:
Serial controller: Device 4348:3253 (rev 10) (prog-if 02 [16550])
Re-using the 353 quirk which just sets flags to fixed and type
to 16550 is suitable for fixing the 352 as well.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've managed to find an 8 port version of the card 4 port card which was discussed here:
http://marc.info/?l=linux-serial&m=120760744205314&w=2
Looking back at that thread there were two issues in the original patch.
1) The I/O ports for the UARTs are within BAR2 not BAR0. This can been seen in the original post.
2) A serial quirk isn't needed as these cards have no memory in BAR0 which makes pci_plx9050_init just return.
This patch fixes the 4 port support to use BAR2, removes the bogus quirk and adds support for the 8 port card.
$ lspci -vvv -n -s 00:08.0
00:08.0 0780: 10b5:9050 (rev 01)
Subsystem: 10b5:1588
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 17
Region 1: I/O ports at ff00 [size=128]
Region 2: I/O ports at fe00 [size=64]
Region 3: I/O ports at fd00 [size=8]
Capabilities: <access denied>
Kernel driver in use: serial
$ dmesg | grep 0000:00:08.0:
[ 0.083320] pci 0000:00:08.0: [10b5:9050] type 0 class 0x000780
[ 0.083355] pci 0000:00:08.0: reg 14: [io 0xff00-0xff7f]
[ 0.083369] pci 0000:00:08.0: reg 18: [io 0xfe00-0xfe3f]
[ 0.083382] pci 0000:00:08.0: reg 1c: [io 0xfd00-0xfd07]
[ 0.083460] pci 0000:00:08.0: PME# supported from D0 D3hot
[ 1.212867] 0000:00:08.0: ttyS4 at I/O 0xfe00 (irq = 17) is a 16550A
[ 1.233073] 0000:00:08.0: ttyS5 at I/O 0xfe08 (irq = 17) is a 16550A
[ 1.253270] 0000:00:08.0: ttyS6 at I/O 0xfe10 (irq = 17) is a 16550A
[ 1.273468] 0000:00:08.0: ttyS7 at I/O 0xfe18 (irq = 17) is a 16550A
[ 1.293666] 0000:00:08.0: ttyS8 at I/O 0xfe20 (irq = 17) is a 16550A
[ 1.313863] 0000:00:08.0: ttyS9 at I/O 0xfe28 (irq = 17) is a 16550A
[ 1.334061] 0000:00:08.0: ttyS10 at I/O 0xfe30 (irq = 17) is a 16550A
[ 1.354258] 0000:00:08.0: ttyS11 at I/O 0xfe38 (irq = 17) is a 16550A
Signed-off-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for later SUNIX (TIMEDIA) Universal PCI Single and Multi-Port
Communications Boards.
These boards have PCI Vendor ID 1fd4 with device ID 1999 but otherwise
appear to be the same as the TIMEDIA boards already supported by 8250_pci
and parport_serial.
Tested with:
a. the two port serial board part number SER5037A,
b. the two port serial and one port parallel board part number
MIO5079A.
Signed-off-by: Stephen Chivers <schivers@csc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the UART device present in Broadcom TruManage capable
NetXtreme chips (ie: 5761m 5762, and 5725).
This implementation has a hidden transmit FIFO, so running in single-byte
interrupt mode results in too many interrupts. The UART_CAP_HFIFO
capability was added to track this. It continues to reload the THR as long
as the THRE and TSRE bits are set in the LSR up to a specified limit (1024
is used here).
Signed-off-by: Stephen Hurd <shurd@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some __devexit markings came in from an older patch, this removes them.
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Woithe posted an out of tree enabler/control module for these
cards. Lift the relevant identifiers and put them in the 8250_pci driver
along with code used to control custom registers on these cards.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The correct device id for this card is 0x0022
Signed-off-by: Matt Schulte <matts@commtech-fastcom.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty/8250: pbn_b0_8_1152000_200 is supposed to be an 8 port definition
Signed-off-by: Matt Schulte <matts@commtech-fastcom.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Commtech's Fastcom Async-335 and Fastcom Async-PCIe cards
Signed-off-by: Matt Schulte <matts@commtech-fastcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add initialization of sampling mode and tx/rx triggers to pci_xr17v35x_setup
Signed-off-by: Matt Schulte <matts@commtech-fastcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for new devices: Exar's XR17V35x family of multi-port PCIe UARTs.
Signed-off-by: Matt Schulte <matts@commtech-fastcom.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current CE4100 and 8250_pci code have both a limitation preventing the
registration and usage of CE4100's second UART. This patch changes the
platform code fixing up the UART port to work on a relative UART port
base address, as well as the 8250_pci code to make it register 2 UART ports
for CE4100 and pass the port index down to all consumers.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we skipped the merge window for 3.6-rc1 for the tty tree, everything
is now settled down and working properly, so we are ready for 3.7-rc1.
Here's the patchset, it's big, but the large changes are removing a
firmware file and adding a staging tty driver (it depended on the tty
core changes, so it's going through this tree instead of the staging
tree.)
All of these patches have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp36oACgkQMUfUDdst+yk4WgCdEy13hot8fI2Lqnc7W0LKu7GX
4p8AoLTjzrXhLosxdijskDQ9X1OtjrxU
=S5Ng
-----END PGP SIGNATURE-----
Merge tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY changes from Greg Kroah-Hartman:
"As we skipped the merge window for 3.6-rc1 for the tty tree,
everything is now settled down and working properly, so we are ready
for 3.7-rc1. Here's the patchset, it's big, but the large changes are
removing a firmware file and adding a staging tty driver (it depended
on the tty core changes, so it's going through this tree instead of
the staging tree.)
All of these patches have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up more-or-less trivial conflicts in
- drivers/char/pcmcia/synclink_cs.c:
tty NULL dereference fix vs tty_port_cts_enabled() helper function
- drivers/staging/{Kconfig,Makefile}:
add-add conflict (dgrp driver added close to other staging drivers)
- drivers/staging/ipack/devices/ipoctal.c:
"split ipoctal_channel from iopctal" vs "TTY: use tty_port_register_device"
* tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (235 commits)
tty/serial: Add kgdb_nmi driver
tty/serial/amba-pl011: Quiesce interrupts in poll_get_char
tty/serial/amba-pl011: Implement poll_init callback
tty/serial/core: Introduce poll_init callback
kdb: Turn KGDB_KDB=n stubs into static inlines
kdb: Implement disable_nmi command
kernel/debug: Mask KGDB NMI upon entry
serial: pl011: handle corruption at high clock speeds
serial: sccnxp: Make 'default' choice in switch last
serial: sccnxp: Remove mask termios caps for SW flow control
serial: sccnxp: Report actual baudrate back to core
serial: samsung: Add poll_get_char & poll_put_char
Powerpc 8xx CPM_UART setting MAXIDL register proportionaly to baud rate
Powerpc 8xx CPM_UART maxidl should not depend on fifo size
Powerpc 8xx CPM_UART too many interrupts
Powerpc 8xx CPM_UART desynchronisation
serial: set correct baud_base for EXSYS EX-41092 Dual 16950
serial: omap: fix the reciever line error case
8250: blacklist Winbond CIR port
8250_pnp: do pnp probe before legacy probe
...
Apparently the same card model has two IDs, so this patch
complements the commit 39aced68d6
adding the missing one.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Covers the rest of the uses of pci error handler.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These were reported in bugzilla long ago with a hack patch. Now we have a
proper patch for one we can do the rest.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=25102
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow parport_serial to handle the card the same PCI ids are blacklisted
in 8250_pci.c using the existing software blacklist mechanism.
The blacklist array is also renamed because it now covers this new use
case.
Since the two serial ports are auto-detected as XScale instead of 16550A
clones, we also add a quirk to 8250_pci.c to skip autodetection and set the
correct port type.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
[Fold in fixes for the uart_8250 change]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Information and a different patch provided by <donald@asix.com.tw>. We do
it a little differently to keep the modularity and to avoid playing with
RLSI.
We add a new uart bug for the parity flaw and set it in the pci matches.
If parity check is enabled then we drop the FIFO trigger to 1 as per the
Asix reference code.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old interface just copies bits over and calls the newer one.
In addition we can now pass more information.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pbn_exsys_4055 is the same thing as pbn_b2_4_115200 so replace it with
the standard pattern.
Signed-off-by: Shawn Bohrer <shawn.bohrer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rules used to make 8250_pci "ignore" the PCH uarts are lacking pci subids
entries, preventing it to match and thus is breaking serial port support for
theses systems.
This has been tested on a nanoETXexpress-TT, which has a specifici uart clock.
Tested-by: Erwan Velu <Erwan.Velu@zodiacaerospace.com>
[stable@: please apply to 3.0-stable, 3.2-stable and 3.3-stable]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Arnaud Patard <apatard@hupstream.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using Serial Over Lan (SOL) over the virtual serial port in a Intel
management engine (ME) device, on device reset the serial FIFOs need to
be cleared to keep the FIFO indexes in-sync between the host and the
engine.
On a reset the serial device assertes BI, so using that as a cue FIFOs
are cleared. So for this purpose a new handle_break callback has been
added. One other problem is that the serial registers might temporarily
go to 0 on reset of this device. So instead of using the IER register
read, if 0 returned use the ier value in uart_8250_port. This is hidden
under a custom serial_in.
Cc: Nhan H Mai <nhan.h.mai@intel.com>
Signed-off-by: Sudhakar Mamillapalli <sudhakar@fb.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko