- Replace magic values with constants
- Simplify length calculation and fix a bug
Based on valuable feedback from Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To help debug the problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent race conditions with other reset events.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.
[ Fix bnx2_free_tx_skbs() ring indexing and use NETDEV_TX_OK return
code in bnx2_start_xmit() after cleaning up DMA mapping errors. -Mchan ]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2 is failing when a PCI error is detected. The error is the
following:
bnx2: Chip not in correct endian mode
bnx2: fw sync timeout, reset code = 404001d
This error was caused because the way pci_restore_state() is working
after commit 4b77b0a2ba ("PCI: Clear
saved_state after the state has been restored").
Signed-off-by: Breno Leitao<leitao@linux.vnet.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/bnx2.c: In function ‘bnx2_enable_forced_2g5’:
drivers/net/bnx2.c:1447: warning: ‘bmcr’ may be used uninitialized in this function
drivers/net/bnx2.c: In function ‘bnx2_disable_forced_2g5’:
drivers/net/bnx2.c:1482: warning: ‘bmcr’ may be used uninitialized in this function
One fix would be to have an initial value, but a plain return might be better.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a couple of cases collapse some extra code like:
int retval = NETDEV_TX_OK;
...
return retval;
into
return NETDEV_TX_OK;
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Better small packet receive performance.
- Better handling of Flow control on 5709.
- Fixed iSCSI TMP ABORT TASK problem.
- Added iSCSI TCP timestamp option.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structure, once initialized, never changes.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Set the USE_INT_PARAM bit so the rx-frames-irq and tx-frames-irq will take
effect on 5709.
- Increase the default rx-frames to reduce interrupt count.
- Decrease the default rx-frames-irq and tx-frames-irq to catch more events
during NAPI poll.
All these will reduce interrupts without affecting latency.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report this counter to ethtool -S and include it in netstat.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unable to allocate memory for new MTU or new ring size, we need
to close the device to prevent it from crashing.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add this check to bnx2_netif_stop() and bnx2_vlan_rx_register() to
prevent bus lockups on some systems when the chip is in low power state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case IRQs are shared, we will not mistakenly start processing
the ring based on old status block indices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The slow path calls to the cnic driver are sleepable calls so we
cannot use rcu_read_lock(). Use mutex for these slow path calls
instead.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI drivers that implement the struct pci_error_handlers' error_detected
callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is
pci_channel_io_perm_failure. This patch fixes the issue for bnx2.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[PATCH net-next-2.6] bnx2: Update vlan_features
In order to get full use of some advanced features of BNX2, we now need to
fill dev->vlan_features.
Patch successfully tested with vlan devices built on top of bonding.
(bond0 : one bnx2 slave, one tg3 slave (not yet vlan_features enabled)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found a little bug.
When configure in ifcfg-eth* is ONBOOT=no,
the behavior of ethtool command is wrong.
# grep ONBOOT /etc/sysconfig/network-scripts/ifcfg-eth2
ONBOOT=no
# ethtool eth2 | tail -n1
Link detected: yes
I think "Link detected" should be "no".
Signed-off-by: Ooiwa Naohiro <nooiwa@miraclelinux.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is inspired by patch recently posted by Johannes Berg. Basically what
my patch does is to group list and a count of addresses into newly introduced
structure netdev_hw_addr_list. This brings us two benefits:
1) struct net_device becames a bit nicer.
2) in the future there will be a possibility to operate with lists independently
on netdevices (with exporting right functions).
I wanted to introduce this patch before I'll post a multicast lists conversion.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 4 +-
drivers/net/e1000/e1000_main.c | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/mv643xx_eth.c | 2 +-
drivers/net/niu.c | 4 +-
drivers/net/virtio_net.c | 10 ++--
drivers/s390/net/qeth_l2_main.c | 2 +-
include/linux/netdevice.h | 17 +++--
net/core/dev.c | 130 ++++++++++++++++++--------------------
9 files changed, 89 insertions(+), 90 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Add interface and functions to support a new CNIC driver to drive
the Broadcom bnx2 hardware for iSCSI offload.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is no need to check if a pointer is NULL before calling
vfree(), since vfree() function already check for it.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_dma_unmap() is quite expensive for small packets,
because we use two different cache lines from skb_shared_info.
One to access nr_frags, one to access dma_maps[0]
Instead of dma_maps being an array of MAX_SKB_FRAGS + 1 elements,
let dma_head alone in a new dma_head field, close to nr_frags,
to reduce cache lines misses.
Tested on my dev machine (bnx2 & tg3 adapters), nice speedup !
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using bnx2 in a high transmit load, bnx2_tx_int() cost is pretty high.
There are two reasons.
One is an expensive call to bnx2_get_hw_tx_cons(bnapi) for each freed skb
One is cpu stalls when accessing skb_is_gso(skb) / skb_shinfo(skb)->nr_frags
because of two cache line misses.
(One to get skb->end/head to compute skb_shinfo(skb),
one to get is_gso/nr_frags)
This patch :
1) avoids calling bnx2_get_hw_tx_cons(bnapi) too many times.
2) makes bnx2_start_xmit() cache is_gso & nr_frags into sw_tx_bd descriptor.
This uses a litle bit more ram (256 longs per device on x86), but helps a lot.
3) uses a prefetch(&skb->end) to speedup dev_kfree_skb(), bringing
cache line that will be needed in skb_release_data()
result is 5 % bandwidth increase in benchmarks, involving UDP or TCP receive
& transmits, when a cpu is dedicated to ksoftirqd for bnx2.
bnx2_tx_int going from 3.33 % cpu to 0.5 % cpu in oprofile
Note : skb_dma_unmap() still very expensive but this is for another patch,
not related to bnx2 (2.9 % of cpu, while it does nothing on x86_32)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add barrier() to bnx2_get_hw_{tx|rx}_cons() to fix this issue:
http://bugzilla.kernel.org/show_bug.cgi?id=12698
This issue was reported by multiple i386 users. Without barrier(),
the compiled code looks like the following where %eax contains the
address of the tx_cons or rx_cons in the DMA status block. The
status block contents can change between the cmpb and the movzwl
instruction. The driver would crash if the value was not 0xff during
the cmpb instruction, but changed to 0xff during the movzwl
instruction.
6828: 80 38 ff cmpb $0xff,(%eax)
682b: 0f b7 10 movzwl (%eax),%edx
With the added barrier(), the compiled code now looks correct:
683d: 0f b7 10 movzwl (%eax),%edx
6840: 0f b6 c2 movzbl %dl,%eax
6843: 3d ff 00 00 00 cmp $0xff,%eax
Thanks to Pascal de Bruijn <pmjdebruijn@pcode.nl> for reporting the
problem and Holger Noefer <hnoefer@pironet-ndh.com> for patiently
testing test patches for us.
Also updated version to 2.0.1.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mips identifier is reserved by gcc on mips plattforms. Don't use it
in the code.
Signed-off-by: Bastian Blank <waldi@debian.org>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_40BIT_MASK macro with DMA_BIT_MASK(40)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on original patch by Ben Hutchings <ben@decadent.org.uk> and
Bastian Blank <waldi@debian.org>, with the following main changes:
Separated the mips firmware and rv2p firmware into different files
to make it easier to update them separately.
Added some code to fixup the rv2p code with run-time information
such as PAGE_SIZE.
Update version to 2.0.0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSI-X handler was chosen before the call to pci_enable_msix().
If MSI-X was not available, the wrong MSI-X handler would be used in
INTA mode. This would cause a screaming interrupt problem because
INTA would not be cleared by the MSI-X handler.
Fixed by assigning MSI-X handler after pci_enable_msix() returns
successfully. Also update version to 1.9.3.
Thomas Chenault <thomas_chenault@dell.com> helped us find this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If errors are reported on a frame descriptor, we need to
account for the buffer pages that may have been used for this
error packet and recycle them. Otherwise, we may get the wrong
pages for the next packet.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the locking is OK as the locks were being taken before the
various phy setup functions, add the annotations as they release and
reacquire the phy_lock.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan