Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
for_each_child_of_node performs an of_node_get on each iteration, so a
goto out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e,e1;
identifier l;
@@
for_each_child_of_node(e1,n) {
...
(
of_node_put(n);
|
e = n
|
return n;
|
+ of_node_put(n);
? goto l;
)
...
}
l: ... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the EtherAVB pin groups to the R8A7791 PFC driver.
Also add the copyright for all the Cogent Embedded's past work on this file.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and a function for SCIF_CLK, which is the external
clock source for the Baud Rate Generator for External Clock (BRG) on
(H)SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add pins, groups, and a function for SCIF_CLK, which is the external
clock source for the Baud Rate Generator for External Clock (BRG) on
(H)SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add pins, groups, and a function for SCIF_CLK, which is the external
clock source for the Baud Rate Generator for External Clock (BRG) on
SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add pins, groups, and a function for SCIF_CLK, which is the external
clock source for the Baud Rate Generator for External Clock (BRG) on
(H)SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add pins, groups, and a function for SCIF_CLK, which is the external
clock source for the Baud Rate Generator for External Clock (BRG) on
(H)SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add pins, groups, and a function for the 4 MSIOF devices.
Note that the pin function name of MSIOF3 is named BBIF1.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pins that (1) can be configured as either GPIO or a single peripheral
function, and (2) that don't need configuration in an IPSRx register,
should still be listed in the pinmux_data[] array.
Else selecting the peripheral function fails with e.g.:
sh-pfc e6060000.pfc: cannot locate data/mark enum_id for mark 1281
(mark 1281 is MSIOF0_SCK_MARK).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When building for SH7734:
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:1: error: macro "_GP_DATA" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:2: error: '_GP_DATA' undeclared here (not in a function)
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:1: error: macro "_GP_DATA" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:1: error: macro "_GP_DATA" passed 5 arguments, but takes just 4
...
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:1: error: macro "_GP_INOUTSEL" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:53: error: '_GP_INOUTSEL' undeclared here (not in a function)
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:2: warning: initialization makes integer from pointer without a cast [enabled by default]
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:2: warning: (near initialization for '(anonymous)[0]') [enabled by default]
...
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:1: error: macro "_GP_INDT" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:47: error: '_GP_INDT' undeclared here (not in a function)
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:2: warning: initialization makes integer from pointer without a cast [enabled by default]
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:2: warning: (near initialization for '(anonymous)[0]') [enabled by default]
...
Add the missing "cfg" macro parameters to the sh7734-specific
_GP_DATA(), _GP_INOUTSEL(), and _GP_INDT() macros to fix this.
Fixes: 22768fc60a ("pinctrl: sh-pfc: Add macros defining GP ports with config flags")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Many SoC needs each PORT_GP_x() macros, but we can share/reuse
same one.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cfr. Manual Errata for Rev 0.50 of the R-Car Gen3 datasheet.
This has no user-visible impact.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
On r8a7795, PORT_GP_x() is a macro for defining GPIOs 0..x.
In all other sh-pfc code, PORT_GP_x() is a macro for defining GPIOs
0..(x-1).
Make the r8a7795 macro definitions consistent with the rest of the
sh-pfc codebase.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Add a macro to describe a pinmux configuration for a single-function
pin.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the removal of the r8a7778 legacy SoC code in commit
4baadb9e05 ("ARM: shmobile: r8a7778: remove obsolete setup code"),
r8a7778 is only supported in generic DT-only ARM multi-platform builds.
The driver doesn't need to match platform devices by name anymore, hence
remove the corresponding platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Since the removal of the r8a7779 legacy SoC code in commit
c99cd90d98 ("ARM: shmobile: r8a7779: Remove legacy SoC code"),
r8a7779 is only supported in generic DT-only ARM multi-platform builds.
The driver doesn't need to match platform devices by name anymore, hence
remove the corresponding platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This header file will be removed soon.
Copy the helper macro RCAR_GP_PIN(), which is used by the pinctrl
drivers only, to sh_pfc.h, and drop the #include.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The sh_pfc_soc_info.gpio_data[] array contains not only GPIO data, but
also various other pinmux-related data (functions and marks).
Every single driver already calls its local array pinmux_data[].
Hence rename the sh_pfc_soc_info member to "pinmux_data".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
On this SoC there is no simple mapping of GP pins to pull-up register
bits, so we need a table.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
PORT_GP_CFG_1 and PORT_GP_CFG_32 work like their non-CFG counterparts
but accept an extra argument with config flags.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add VIN0/1 pin groups to R8A7794 PFC driver.
Sergei: rebased, renamed, added changelog, gathered 12 VIN1 data pins into
a single pin group, added "vin1_data10" pin group, used 'union vin_data' and
VIN_DATA_PIN_GROUP() macro to describe VIN1 pins, reversed the order of the
VIN1 pin groups, removed unneeded empty lines, fixed VIN1 separator comment.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R8A7790/1 PFC drivers use almost identical 'union vin_data' and completely
identical VIN_DATA_PIN_GROUP() macro; we thus can move them into the shared
header file...
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds EthernetAVB
Based on a much lager patch by Takeshi Kihara which was
originally posted by Kuninori Morimoto.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms: extracted from a larger patch;
corrected swapped {MATCH,CAPTURE_A} pins]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Now, PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA() are same.
Current PFC driver is very difficult to read, because macro names are
using different length.
PINMUX_IPSR_NOGP(ispr, ...)
PINMUX_IPSR_DATA(ipsr, ...)
PINMUX_IPSR_NOGM(ispr, ...)
PINMUX_IPSR_NOFN(ipsr, ...)
PINMUX_IPSR_MSEL(ipsr, ...)
PINMUX_IPSR_MODSEL_DATA(ipsr, ...)
It can be readable if we can use PINMUX_IPSR_MSEL() instead
of PINMUX_IPSR_MODSEL_DATA()
PINMUX_IPSR_NOGP(ispr, ...)
PINMUX_IPSR_DATA(ipsr, ...)
PINMUX_IPSR_NOGM(ispr, ...)
PINMUX_IPSR_NOFN(ipsr, ...)
PINMUX_IPSR_MSEL(ipsr, ...)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Linus Torvalds