We're going to remove the FIRMWARE_NAME_MAX definition in order to avoid any
firmware name length restriction.
This patch replaces the shared FIRMWARE_NAME_MAX definition with a ueagle
local one.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Cc: Damien Bergamini <damien.bergamini@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
Interface blacklisting is necessary for non-serial interfaces that are handled
by a different driver. The interface blacklisting is implemented in sierra
driver per device. Each device in need of a blacklist has a static information
array kept in the driver. This array contains the interface numbers that are
blacklisted. The pointer for each blacklist array and the length
of that blacklist are 'bundled' in data structure sierra_iface_info. A pointer
to this information is set in id_table when the device is added to the id_table.
The following is summary of changes we have made to sierra.c driver in
this patch dealing with interface blacklisting support:
- Added data structure sierra_iface_info and function is_blacklisted()
to support blacklisting
- Modified sierra_probe() to handle blacklisted interfaces accordingly
- Improved comments in id_table
- Added new device in id_table with blacklist interface support
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[Folded from eight patches into one as the original set according to the
author "All of the patches need to be applied to obtain a working product"
so keeping them split seems unhelpful
Merge fixes done versus other conflicting changes and moved the
spin_lock_init from open to setup time -- Alan]
Summary of the changes and code re-organization in this patch:
- The memory for urbs is allocated and urbs are submitted only for the active
interfaces (instead of pre-allocating these for all interfaces). This will
save memory especially in the case of using composite devices.
- The code has been re-organized and functionality has been extracted from
sierra_startup(), sierra_shutdown(), sierra_open(), sierra_close() and added
in helper functions sierra_release_urb(), sierra_stop_rx_urbs(),
sierra_submit_rx_urbs() and sierra_setup_urb()
- Added function sierra_release_urb() to free an urb and its transfer
buffer.
- Removed unecessary include file reference and comment.
- Added function sierra_stop_rx_urbs() that takes care of the release of
receive and interrupt urbs. This function is to be called by sierra_close()
whenever an interface is de-activated.
- Added new function sierra_submit_rx_urbs() that handles the submission of
receive urbs and interrupt urbs (if any) during the interface activation.
This function is to be called by sierra_open(). Added a second parameter to
pass the memory allocation (as suggested by Oliver Neukum) so that this
function can be used in post_reset() and resume().
- Added new function sierra_setup_urb() that contains the functionality to
allocate an urb, fill bulk urb using the supplied memory allocation flag
and release urb upon error. Added parameter so that the caller pass the
memory allocation flag for flexibility.
- Moved sierra_close() before sierra_open() to resolve dependencies
introduced by the code reorganization.
- Modified sierra_close() to call sierra_stop_rx_urbs() and
sierra_release_urb() functions added in previous patch.
- Modified sierra_open() to call sierra_setup_urb() and sierra_submit_rx_urbs()
functions; note urbs are allocated and submitted for each activated interface.
- Modified sierra_startup() so that allocation of urbs happens whenever an
interface is activated (urb allocation is moved to sierra_open()).
- Modified sierra_shutdown() so that urbs are freed whenever an interface is
de-activated (urb freeing moved to sierra_close() as shown in previous patch
from the series)
- Removed unecessary data structure from sierra_port_private_data
- Suppress an entry in logs by not re-submitting an urb when usb_submit_urb()
returns -EPERM, as this shows that usb_kill_urb() is running (as suggested by
Oliver Neukum)
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Alan Cox <alan.cox@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The various merges into the sierra driver inadvertently undid
commit 212b8f0c3f by Elina Pasheva
<epasheva@sierrawireless.com>. Put it back so the OBEX port works again.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new open/close logic handles DTR and friends, so don't do it in our own
open routine as well.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows users to use the standard setserial command with this FT232
feature as well as obscure chip specific interfaces we have now. We keep
track of and respect the sysfs value for non-low-latency cases. In theory we
could do smart stuff with VTIME and the like but this seems of questionable
worth.
Closes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=9120
Signed-off-by: Alan Cox <alan@linux.intel.com)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces the string "CP2101" with "CP210x" within cp210x.c
This is to reduce confusion about the fact that the driver is actually
compatible with CP2101, CP2102 and CP2103 devices.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
(Fixed some collisions merging)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CP210X driver was developed without official device specifications.
This has lead to an incorrect assumption that all GET request codes are
equal to the corresponding SET request code +1.
This patch removes this incorrect assumption, and uses request code
definitions based on the updated GPL driver from SiLabs.
This modification is needed before extended functionality such as GPIO
on CP2103 can be supported.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
set_termios can now be used for setting the parity and the stopbits. This is
needed to use with cards which use a different parity then the parity used at
start (even).
If the iuu_uart_baud function return an error, we will return the old_termios
instead of the new one.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
This was then revamped to use the various helpers, not copy non-hardware
bits any to add mark/space parity and csize reporting
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bring in the relevant bits of the 0.9 vendor driver.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Or at least most of it. There are further clean ups possible and there are
are also thing checkpatch moans about that would be silly to "fix".
Also note some FIXME points found as the cleanup was done.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now we have a port structure begin using the fields and kref counts
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CDC ACM driver uses the tty layer correctly so needs conversion. Start by
adding and initializing the port structures.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to clean stuff up, but is probably also going to cause
some app breakage with buggy apps as we now implement proper POSIX behaviour
for USB ports matching all the other ports. This does also mean other apps
that break on USB will now work properly.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network device TX is never run in IRQ context, and skb is freed outside
of the IRQ-disabling spin lock. So checking for IRQ was a waste of time
here.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup the ohci-ep93xx driver.
1) Use the usb.h dbg() macro instead of pr_debug() so that
the source filename is prefixed to the message and it is
terminated with a linefeed.
2) Add error handling for the clk_get() call.
3) Update clkdev support so that the usb clock is matched by
the dev_id instead of the con_id.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 26e1287594.
A larger patch (f7e7aa585) a few days after this one added the same line
to the Makefile, but in a different place. While it'd be more correct to
revert that one, it's easier to revert this one because this is a
one-liner.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1244) fixes a crash in usb-serial that occurs when a
sub-driver returns a positive value from its attach method, indicating
that new firmware was loaded and the device will disconnect and
reconnect. The usb-serial core then skips the step of registering the
port devices; when the disconnect occurs, the attempt to unregister
the ports fails dramatically.
This problem shows up with Keyspan devices and it might affect others
as well.
When the attach method returns a positive value, the patch sets
num_ports to 0. This tells usb_serial_disconnect() not to try
unregistering any of the ports; instead they are cleaned up by
destroy_serial().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The option driver (and presumably others) allocates several URBs when it
opens and tries to free them when it closes. The isp1760_urb_dequeue
function gets called, but the packet being dequeued is not necessarily at
the
front of one of the 32 queues. If not, the isp1760_urb_done function doesn't
get called for the URB and the process trying to free it hangs forever on a
wait_queue. This patch does two things. If the URB being dequeued has others
queued behind it, it re-queues them. And it searches the queues looking for
the URB being dequeued rather than just looking at the one at the front of
the queue.
[bigeasy@linutronix] whitespace fixes, reformating
Cc: stable <stable@kernel.org>
Signed-off-by: Warren Free <wfree@ipmn.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds another quirky Conexant USB Modem Clone to usb cdc-acm.c
Signed-off-by: Xiao Kaijian <xiaokj@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This ensures that all fields are properly initialized.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usbtest #14 was failing with "udc: ep0: TXCOMP: Invalid endpoint state 2, halting endpoint..."
This occured since ep0 is bidirectional and ep->is_in is not valid (must always use ep->state)
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert all external users of queue limits to using wrapper functions
instead of poking the request queue variables directly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commit c45d6320 ("fix reference counting of ftdi_private") stopped
ftdi_sio_port_remove() from directly freeing the port-private data, with
the intention if the port was still open, it would be freed when
ftdi_close() is eventually called and releases the last refcount on the
structure.
That's all very well, but ftdi_sio_port_remove() still contains a call
to usb_set_serial_port_data(port, NULL) -- so by the time we get to
ftdi_close() for the port which was unplugged, it _still_ oopses on
dereferencing that NULL pointer, as it did before (and does in 2.6.29).
The fix is just not to clear the private data in ftdi_sio_port_remove().
Then the refcount is properly reduced to zero when the final kref_put()
happens in ftdi_close().
Remove a bogus comment too, while we're at it. And stop doing things
inside "if (priv)" -- it must _always_ be there.
Based loosely on an earlier patch by Daniel Mack, and suggestions by
Alan Stern.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1238) adds proper reference counting for ftdi_sio's
private data structure. Without it, the driver will free the
structure while it is still in use if the user unplugs the serial
device before closing the device file.
The patch also replaces a slightly dangerous
cancel_delayed_work/flush_scheduled_work pair with
cancel_delayed_work_sync, which is always safer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Daniel Mack <daniel@caiaq.de>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch was originaly submitted by Phillip Potter
<phillipinda@hotmail.com> but was re-diffed to conform with
SubmittingPatches and to rebase on a newer tree by me.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1234) fixes a bug in the UTF8 -> UTF-16 conversion
routine in the gadget/usbstring library. In a UTF-8 multi-byte
sequence, all bytes after the first should have their high-order
two bits set to 10, not 11.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If CONFIG_USB_ACM and CONFIG_USB_PRINTER are not set, then
cdc-wdm and usbtmc won't get built.
Signed-off-by: Andy Lutomirski <amluto@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Values of dB between -0.99 and -0.01 will be output with the wrong
sign. This converts the negative value to positive and outputs it
with a "-" prefix.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the case where a gadget driver is removed while no
transceiver was found at probe time, a bug in
otg_put_transceiver() will trigger.
Provide symetric calls for otg_get_transceiver() and
otg_put_transceiver(), wherever a transceiver was found or
not.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch to cdc-wdm
- checks for partial extra descriptors
- fixes a leak in the error case of probe
- checks for an exact number of endpoints
- adds a clarifying comment
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes tty->low_latency from all USB serial drivers that push
data into the tty layer at hard interrupt context. It's no longer needed
and actually harmful.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a problem in sierra_send_setup() function when
composite devices are used. One should not be sending ACM commands to
interfaces that are OBEX. Doing this causes an apparent failure as the
ACM command has to time out before the interface can start being used.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We now have a more correct solution for shrinking runtime driver
footprints than just marking probe() as __init ... use it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build error in the MIPS USB IP core family device controller driver.
The driver calls udelay() without including linux/delay.h
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When I want to use my webcam, I get:
vvvvvvv
cheese: page allocation failure. order:5, mode:0x8004
Pid: 8100, comm: cheese Not tainted 2.6.30-rc2-wl-dirty #102
Call Trace:
[<ffffffff802c5d8e>] __alloc_pages_internal+0x3fe/0x520
[<ffffffff80210a20>] dma_generic_alloc_coherent+0x90/0x120
[<ffffffffa001c91e>] hcd_buffer_alloc+0xee/0x130 [usbcore]
[<ffffffffa000d52d>] usb_buffer_alloc+0x2d/0x40 [usbcore]
[<ffffffffa0160e14>] uvc_alloc_urb_buffers+0x84/0x140 [uvcvideo]
[<ffffffffa0160ff6>] uvc_init_video+0x126/0x400 [uvcvideo]
[...]
Oddly, I remembered fixing this and putting in __GFP_NOWARN
because uvcvideo retries a smaller allocation. However, the
allocation function doesn't pass the gfp flags through to
dma_alloc_coherent so we still get the warning!
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1231) fixes a use-after-free bug in g_file_storage. A
device's name may not be available after the device is unregistered,
even if the device structure itself is still allocated. Since
close_backing_file() prints a LUN's name for debugging, it shouldn't
be called after the LUN has been unregistered.
That whole area needed to be cleaned up; the backing files were
getting closed in a couple of different places. The patch fixes
things so that they get closed in just one place, as part of the
unbind procedure, immediately before the LUN is unregistered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without this patch, the driver won't check that the last fully-occupied
uframe for a new split transaction was vacant beforehand. This can
lead to a situation in which the first 188 bytes of a 192-byte
isochronous transfer are scheduled in the same uframe as an existing
interrupt transfer. The resulting schedule looks like this:
uframe 0: 188-byte isoc-OUT SSPLIT, 8-byte int-IN SSPLIT
uframe 1: 4-byte isoc-OUT SSPLIT
The SSPLITs are intermingled, causing an error in the downstream hub's
TT.
If you are having problems with devices or hub ports resetting, or failed
interrupt transfers, when you start using a USB audio or video (Isochronous)
device, this patch may help.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Reported-by: Kung James <kong1191@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
This patch fixes a problem with any mos7840 device where the use of the field "minor" before it is
initialised results in all the devices being overlaid in memory (minor = 0 for all instances)
Contributed by: Phillip Branch
Signed-off-by: Tony Cook <tony-cook@bigpond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
add USB ids for the mos7840 based ATEN International serial devices.
Contributed by: Phillip Branch
Signed-off-by: Tony Cook <tony-cook@bigpond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix this build error when CONFIG_PM is not set:
drivers/usb/musb/musb_core.c:2232: error: 'musb_resume_early' undeclared here
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This email address is going to expire soon and my contribution to musb
is next to zero so remove it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bug Fix: high speed detection in LPM mode
Bug Fix: max packet size configuration when switching between HS and FS
Signed-off-by: David Lopo <dlopo@chipidea.mips.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported by Alessio Treglia on
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/125250
User was getting the following errors in dmesg:
[ 2158.139386] sd 5:0:0:1: ioctl_internal_command return code = 8000002
[ 2158.139390] : Current: sense key: No Sense
[ 2158.139393] Additional sense: No additional sense information
Adds unusual device support.
modified: drivers/usb/storage/unusual_devs.h
Signed-off-by: Chuck Short <zulcss@ubuntu.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1229) fixes a few lifetime and locking problems in the
usb-serial driver. The main symptom is that an invalid kevent is
created when the serial device is unplugged while a connection is
active.
Ports should be unregistered when device is disconnected,
not when the parent usb_serial structure is deallocated.
Each open file should hold a reference to the corresponding
port structure, and the reference should be released when
the file is closed.
serial->disc_mutex should be acquired in serial_open(), to
resolve the classic race between open and disconnect.
serial_close() doesn't need to hold both serial->disc_mutex
and port->mutex at the same time.
Release the subdriver's module reference only after releasing
all the other references, in case one of the release routines
needs to invoke some code in the subdriver module.
Replace a call to flush_scheduled_work() (which is prone to
deadlocks) with cancel_work_sync(). Also, add a call to
cancel_work_sync() in the disconnect routine.
Reduce the scope of serial->disc_mutex in serial_disconnect().
The only place it really needs to protect is where the
"disconnected" flag is set.
This fixes the bug reported in
http://bugs.freedesktop.org/show_bug.cgi?id=20703
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dan Williams <dcbw@redhat.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the wusb_chid sysfs file match the ABI documentation.
Print all zeros if the WUSB host is stopped (instead of an empty file)
and end the file with a newline.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix an oops in wusbhc_giveback_urb() if the wusb device had disconnected
while an urb was in progress. Also release the ref count obtained here.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure all WUSB devices are disconnected when stopping a WUSB HCD so
that we don't leak the devices' wusb_dev structures.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check the return value of usb_hcd_link_urb_to_ep() and do not add the
urb to the ASL/PZL if it returns an error.
Omitting the check results in urbs that appear to be submitted
successfully but then cannot be unliked (because
usb_hcd_check_unlink_urb() returns an error). This can cause khubd (for
example) to block forever in usb_kill_urb().
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Provide a endpoint_reset method to reset sequence number and current
window. This QHead information can only be changed while the qset is
not in a schedule.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wireless USB endpoint state has a sequence number and a current
window and not just a single toggle bit. So allow HCDs to provide a
endpoint_reset method and call this or clear the software toggles as
required (after a clear halt, set configuration etc.).
usb_settoggle() and friends are then HCD internal and are moved into
core/hcd.h and all device drivers call usb_reset_endpoint() instead.
If the device endpoint state has been reset (with a clear halt) but
the host endpoint state has not then subsequent data transfers will
not complete. The device will only work again after it is reset or
disconnected.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The v950 appears to be a ruggedized version of the Motorola Razor
phone. Tethering to the phone to use it in 'phone as modem' mode
requires the use of the specialized moto-modem driver which layers
over the usb-serial driver. Support for the v950 was added simply
adding the device ID's for the phone.
Signed-off-by: Dr. Greg Wettstein <greg@enjellic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1228) fixes a Makefile error introduced when the
subdrivers in usb-storage were split out into separate modules. The
intention is that when CONFIG_USB_LIBUSUAL is set, libusual.o and
usual-tables.o should be combined into a single object file (called
usb-libusual). The current Makefile will instead create two separate
objects, and the result won't load properly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Alan Jenkins <sourcejedi.lkml@googlemail.com>
Reported-and-tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 664d5df92e upstream.
Fixup of Werner Cornelius patch to the ch341 USB-serial driver, which adds:
- support all baudrates, not just a hard-coded set
- support for controlling DTR, RTS and CTS
Features still missing:
- character length other than 8 bits
- parity settings
- break control
I adapted his patch for the new usb_serial API introduced in 2.6.25-git8 by
Alan Cox on 22 July 2008. Non-compliance to the new API was a reason for
refusing a similar patch from Tollef Fog Heen.
Usage example by Tollef Fog Heen :
TEMPer USB thermometer <http://err.no/src/TEMPer.c>
based on a patch by:
From: Tollef Fog Heen <tfheen@err.no>
* Implement support for all baud rates rather than just a hard
coded set.
* Make it possible to control status and control lines
* Grab a bunch of #defines from FreeBSD to reduce the number of
magic numbers in the file
Signed-off-by: Werner Cornelius <Werner.Cornelius@cornelius-consult.de>
Signed-off-by: Boris Hajduk <boris@hajduk.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Tollef Fog Heen <tfheen@err.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reverts commit 664d5df92e as the commit
log information was not complete, and we didn't have a proper
signed-off-by by the author of the original BSD code.
Cc: Werner Cornelius <Werner.Cornelius@cornelius-consult.de>
Cc: Boris Hajduk <boris@hajduk.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During driver resume processing, musb could cause a kernel panic.
Fix by enabling the clock earlier, with the resume_early method.
Signed-off-by: Kim Kyuwon <q1.kim@samsung.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Multi-frame isochronous TX URBs transfers in DMA mode never
complete with CPPI DMA because musb_host_tx() doesn't restart
DMA on the second frame, only emitting a debug message.
With Inventra DMA they complete, but in PIO mode. To fix:
- Factor out programming of the DMA transfer from
musb_ep_program() into musb_tx_dma_program();
- Reorder the code at the end of musb_host_tx() to
facilitate the fallback to PIO iff DMA fails;
- Handle the buffer offset consistently for both
PIO and DMA modes;
- Add an argument to musb_ep_program() for the same
reason (it only worked correctly with non-zero
offset of the first frame in PIO mode);
- Set the completed isochronous frame descriptor's
'actual_length' and 'status' fields correctly in
DMA mode.
Also, since CPPI reportedly doesn't like sending isochronous
packets in the RNDIS mode, change the criterion for this
mode to be used only for multi-packet transfers. (There's
no need for that mode in the single-packet case anyway.)
[ dbrownell@users.sourceforge.net: split comment paragraph
into bullet list, shrink patch delta, style tweaks ]
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The MUSB code clears TXCSR_DMAMODE incorrectly in several
places, either asserting that TXCSR_DMAENAB is clear (when
sometimes it isn't) or clearing both bits together. Recent
versions of the programmer's guide require DMAENAB to be
cleared first, although some older ones didn't.
Fix this and while at it:
- In musb_gadget::txstate(), stop clearing the AUTOSET
and DMAMODE bits for the CPPI case since they never
get set anyway (the former bit is reserved on DaVinci);
but do clear the DMAENAB bit on the DMA error path.
- In musb_host::musb_ep_program(), remove the duplicate
DMA controller specific code code clearing the TXCSR
previous state, add the code to clear TXCSR DMA bits
on the Inventra DMA error path, to replace such code
(executed late) on the PIO path.
- In musbhsdma::dma_channel_abort()/dma_controller_irq(),
add/use the 'offset' variable to avoid MUSB_EP_OFFSET()
invocations on every RXCSR/TXCSR access.
[dbrownell@users.sourceforge.net: don't introduce CamelCase,
shrink diff]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We really want to use DMA mode 1 for all multi-packet transfers;
that's one IRQ on DMA completion, instead of one per packet.
There is an important issue with such transfers, especially on
the host side: when such transfers end with a full-size packet,
we must defer musb_dma_completion() calls until the FIFO empties.
Else we report URB completions too soon, and may clobber data in
the FIFO fifo when writing the next packet (losing data).
The Inventra DMA support uses DMA mode 1, but it ignores that
issue. The CPPI DMA support uses mode 0, but doesn't handle
its TXPKTRDY interrupts quite right either; it can get stale
"packet ready" interrupts, and report transfer completion too
early using slightly different code paths, also losing data.
So I'm solving it in a generic way -- by adding a sort of the
"interrupt filter" into musb_host_tx(), catching these cases
where a DMA completion IRQ doesn't suffice and removing some
needlessly controller-specific logic. When a TXDMA interrupt
happens and DMA request mode 1 is active, that filter resets
to mode 0 and defers URB completion processing until TXPKTRDY,
unless the FIFO is already empty. Related filtering logic in
Inventra and CPPI code gets removed.
Since it should be competely safe now to use the DMA request
mode 1 for host side transfers with the CPPI DMA controller,
set it in musb_h_tx_dma_start() ... now renamed (and shared).
[ dbrownell@users.sourceforge.net: don't introduce more
CamElCase; use more concise explanations ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The MUSB host side can't share generic TX FIFO flush logic
with EP0; the EP0 TX status register bits are different
from those for other entpoints.
Resolve this issue by providing a new EP0-specific routine
to flush and reset the FIFO, which pays careful attention to
restrictions listed in the latest programmer's guide. This
gets rid of an open issue whereby the usbtest control write
test (#14) failed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1227) adds the MAX_SECTORS_64 flag to the unusual_devs
entry for the Simple Tech/Datafab controller. This fixes Bugzilla
#12882.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: binbin <binbinsh@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Someone noted that the enqueue path used an unlocked access
for usb_host_endpoint->hcpriv ... fix that, by being safe
and always accessing it under spinlock protection.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a set of device IDs from the Windows drivers. These aren't complete
(there's a couple of cases where a QDL device is identified without the
associated modem being identified), but it's better than the current
situation.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch allows D-Link DWM-652 3.5G modem to work.
It is an express card but was only tested with the provided usb adapter as I
don't have machines with express card connector.
/dev/ttyUSB{0,1,2} get created, and using comgt on ttyUSB1 works fine :
[root@plop tmp]# comgt -d /dev/ttyUSB1 -e
Enter PIN number: XXXX
Waiting for Registration..(120 sec max).
Registered on Home network: "Orange France",2
Signal Quality: 15,99
From: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The g_ether USB gadget driver currently decides whether or not there's a
link to report back for eth_get_link based on if the USB link speed is
set. The USB gadget speed is however often set even before the device is
enumerated. It seems more sensible to only report a "link" if we're
actually connected to a host that wants to talk to us. The patch below
does this for me - tested with the PXA27x UDC driver.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the ti-usb adapter returns an zero data length frame (which happens)
then we leak a kref. Found by Christoph Mair <christoph.mair@gmail.com>
who proposed a patch. The patch here is different as Christoph's patch
didn't work for the case where tty = NULL and data arrived but Christoph
did all the hard work chasing it down.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ACM sets the low latency flag but calls the flip buffer routines from
IRQ context which isn't permitted (and as of 2.6.29 causes a warning
hence this one was caught)
Fortunatelt ACM doesn't need to set this flag in the first place as it
only set it to work around problems in ancient (pre tty flip rewrite)
kernels.
Reported-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the second go through of the old DMA_nBIT_MASK macro,and there're not
so many of them left,so I put them into one patch.I hope this is the last round.
After this the definition of the old DMA_nBIT_MASK macro could be removed.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5446/1: ohci-at91: Limit vbus_pin assignment to the size of the array
[ARM] 5445/1: AT91: Remove flexible array from USBH platform data
[ARM] 5447/1: Add SZ_32K
[ARM] omap: fix omap1 clock usecount decrement bug
[ARM] pxa: register AC97 controller devices
[ARM] pxa/csb701: do not register devices on non-csb726 boads
[ARM] pxa/colibri: get rid of set_irq_type()
[ARM] pxa/colibri: provide MAC address from ATAG_SERIAL
[ARM] pxa/cm-x2xx: fix ucb1400 not being registered
[ARM] pxa: Add support for suspend on PalmTX, T5 and LD
[ARM] pxa: PalmTE2 support for battery, UDC, IrDA and backlight
[ARM] pxa: Palm Tungsten E2 basic support
[ARM] pxa/em-x270: add libertas device registration
[ARM] pxa/magician: Enable bq24022 regulator for gpio_vbus and pda_power
Currently, the vbus_pin assignment loop is limited by the value of the "ports"
variable in the platform data. Now that the vbus_pin array is no longer
flexible, we can use its actual size.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace all DMA_31BIT_MASK macro with DMA_BIT_MASK(31)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are various bits of code here that are unfinished and instead of
being harmless either confuse or spew stuff into the logs at higher than
debug level. They can and should go away.
Also remove the bogus use of tty->lowlatency. We fixed the need for this hack
long ago (with the flip buffer rewrite) but people keep copying it into drivers.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bugzilla #9095 and a couple of other confirmations
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The cdc_acm module is missing the char-major-166-* alias that would
cause it to be auto-loaded when a device of that type is opened. This
patch adds the alias.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'avr32-arch' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: add hardware handshake support to atmel_serial
avr32: add RTS/CTS/CLK pin selection for the USARTs
Add RTC support for Merisc boards
avr32: at32ap700x: setup DMA for AC97C in the machine code
avr32: at32ap700x: setup DMA for ABDAC in the machine code
Add Merisc board support
avr32: use gpio_is_valid() to check USBA vbus_pin I/O line
atmel-usba-udc: use gpio_is_valid() to check vbus_pin I/O line
avr32: fix timing LCD parameters for EVKLCD10X boards
avr32: use GPIO line PB15 on EVKLCD10x boards for backlight
avr32: configure MCI detect and write protect pins for EVKLCD10x boards
avr32: set pin mask to alternative 18 bpp for EVKLCD10x boards
avr32: add pin mask for 18-bit color on the LCD controller
avr32: fix 15-bit LCDC pin mask to use MSB lines
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/linux-hdreg-h-cleanup:
remove <linux/ata.h> include from <linux/hdreg.h>
include/linux/hdreg.h: remove unused defines
isd200: use ATA_* defines instead of *_STAT and *_ERR ones
include/linux/hdreg.h: cover WIN_* and friends with #ifndef/#endif __KERNEL__
aoe: WIN_* -> ATA_CMD_*
isd200: WIN_* -> ATA_CMD_*
include/linux/hdreg.h: cover struct hd_driveid with #ifndef/#endif __KERNEL__
xsysace: make it 'struct hd_driveid'-free
ubd_kern: make it 'struct hd_driveid'-free
isd200: make it 'struct hd_driveid'-free
It is a fairly common operation to have a pointer to a work and to need a
pointer to the delayed work it is contained in. In particular, all
delayed works which want to rearm themselves will have to do that. So it
would seem fair to offer a helper function for this operation.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Factor out debug dump of id from isd200_get_inquiry_data()
to isd200_dump_driveid().
* Change id field in struct isd200_info from 'struct hd_driveid *id'
to 'u16 *id' and update driver accordingly.
* Include <linux/ata.h> directly instead of through <linux/hdreg.h>.
While at it:
* Use ata_id_u32() and ata_id_has_lba() macros.
There should be no functional changes caused by this patch.
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It doesn't change the semantics, but clearly
the logical 'and' was meant to be used here.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (422 commits)
[ARM] 5435/1: fix compile warning in sanity_check_meminfo()
[ARM] 5434/1: ARM: OMAP: Fix mailbox compile for 24xx
[ARM] pxa: fix the bad assumption that PCMCIA sockets always start with 0
[ARM] pxa: fix Colibri PXA300 and PXA320 LCD backlight pins
imxfb: Fix TFT mode
i.MX21/27: remove ifdef CONFIG_FB_IMX
imxfb: add clock support
mxc: add arch_reset() function
clkdev: add possibility to get a clock based on the device name
i.MX1: remove fb support from mach-imx
[ARM] pxa: build arch/arm/plat-pxa/mfp.c only when PXA3xx or ARCH_MMP defined
Gemini: Add support for Teltonika RUT100
Gemini: gpiolib based GPIO support v2
MAINTAINERS: add myself as Gemini architecture maintainer
ARM: Add Gemini architecture v3
[ARM] OMAP: Fix compile for omap2_init_common_hw()
MAINTAINERS: Add myself as Faraday ARM core variant maintainer
ARM: Add support for FA526 v2
[ARM] acorn,ebsa110,footbridge,integrator,sa1100: Convert asm/io.h to linux/io.h
[ARM] collie: fix two minor formatting nits
...
* 'bkl-removal' of git://git.lwn.net/linux-2.6:
Rationalize fasync return values
Move FASYNC bit handling to f_op->fasync()
Use f_lock to protect f_flags
Rename struct file->f_ep_lock
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (97 commits)
USB: qcserial: add device id for HP devices
USB: isp1760: Add a delay before reading the SKIPMAP registers in isp1760-hcd.c
USB: allow malformed LANGID descriptors
USB: pxa27x_udc: typo fixes and code cleanups
USB: gadget: gadget zero uses new suspend/resume hooks
USB: gadget: composite device-level suspend/resume hooks
USB: r8a66597-hcd: suspend/resume support
USB: more u32 conversion after transfer_buffer_length and actual_length
USB: Fix cp2101 USB serial device driver termios functions for console use
USB: CP2101 New Device ID
USB: ipaq: handle 4 endpoint devices
USB: S3C: Move usb-control.h to platform include
USB: ohci-hcd: Add ARCH_S3C24XX to the ohci-s3c2410.c glue
USB: pedantic: spelling correction in comment for ch9.h
USB: host: fix sparse warning: Using plain integer as NULL pointer
USB: ohci-s3c2410: fix name of bus clock
USB: ohci-s3c2410: remove <mach/hardware.h> include
USB: serial: rename cp2101 driver to cp210x
USB: CP2101 Reduce Error Logging
USB: CP2101 Support AN205 baud rates
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (96 commits)
sh: add support for SMSC Polaris platform
sh: fix the HD64461 level-triggered interrupts handling
sh: sh-rtc wakeup support
sh: sh-rtc invalid time rework
sh: sh-rtc carry interrupt rework
sh: disallow kexec virtual entry
sh: kexec jump: fix for ftrace.
sh: kexec: Drop SR.BL bit toggling.
sh: add kexec jump support
sh: rework kexec segment code
sh: simplify kexec vbr code
sh: Flush only the needed range when unmapping a VMA.
sh: Update debugfs ASID dumping for 16-bit ASID support.
sh: tlb-pteaex: Kill off legacy PTEA updates.
sh: Support for extended ASIDs on PTEAEX-capable SH-X3 cores.
sh: sh7763rdp: Change IRQ number for sh_eth of sh7763rdp
sh: espt-giga board support
sh: dma: Make G2 DMA configurable.
sh: dma: Make PVR2 DMA configurable.
sh: Move IRQ multi definition of DMAC to defconfig
...
This patch will convert to use gpio_is_valid() to check the vbus_pin
platform data. It will also default to -ENODEV if no vbus_pin is
defined.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Replace references to bus_id with dev_name() to fix fhci driver build break.
drivers/usb/host/fhci-hcd.c:586: error: struct device has no member named bus_id
drivers/usb/host/fhci-hcd.c:653: error: struct device has no member named bus_id
drivers/usb/host/fhci-dbg.c:111: error: struct device has no member named bus_id
Signed-off-by: Sachin Sant <sachinp@in.ibm.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The data read from the SKIPMAP registers is not immediately available
after writing and the driver panics when a packet is enqueued from the
interrupt handler. This patch adds an ndelay(195) before these registers
are read (delay value mentioned in section 15.1.1.3 of the ISP1760 data
sheet).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When an USB hardware does not provide a valid LANGID, fall back to value
zero which is still a reasonable default for most devices.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is a merge of patches :
- fix function doc and debug
- cleanup loop count
- optimize code to remove local variable and extra check
- init 'req' before use
- add missing iounmap call
[dbrownell@users.sourceforge.net: capitalize IN/OUT directions in doc]
Signed-off-by: Vernon Sauder <vsauder@inhand.com>
[folded by Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the new device-level suspend/resume hooks for Gadget Zero;
always enable them with the OTG test mode; and support remote
wakeup on both configurations even in non-OTG mode.
This ensures that both configurations can pass the USBCV remote
wakeup tests when the OTG test mode is enabled. This changes
behavior by adding autoresume support to the loopback config
even in non-OTG mode; the test failure was that it didn't work
in OTG mode.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Address one open question in the composite gadget framework:
Yes, we should have device-level suspend/resume callbacks
in addition to the function-level ones. We have at least one
scenario (with gadget zero in OTG test mode) that's awkward
to handle without it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the problem that system cannot suspend.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
transfer_buffer_length and actual_length have become unsigned, therefore some
additional conversion of local variables, function arguments and print
specifications is desired.
A test for a negative urb->transfer_buffer_length became obsolete; instead
we ensure that it does not exceed INT_MAX. Also, urb->actual_length is always
less than urb->transfer_buffer_length.
rh_string() does no longer return -EPIPE in the case of an unsupported ID.
Instead its only caller, rh_call_control() does the check.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is really a follow up to the modifications Alan Cox made for commit
95da310e66 to pass a tty_struct to various
interface functions, which broke the serial configuration (termios) functions
when the device is being used as a console. These changes restore the
configuration to proper functioning both as a tty and as a console. As Alan
notes in that commit, these changes will need to be tweaked when we have
a proper console abstraction.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ipaq driver currently enforces one port on all devices. This
is correct for 2 and 3 endpoint devices, but with 4 endpoint devices
meaningful communication occurs on the second pair.
This patch allows 2 ports for 4 endpoint devices.
Signed-off-by: Mark Ellis <mark@mpellis.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb-control.h is needed by ohci-s3c2410.c for both S3C24XX and S3C64XX
architectures, so move it to <plat/usb-control.h>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ohci-s3c2410.c glue supports both CONFIG_ARCH_S3C2410 and
CONFIG_ARCH_S3C64XX so add it to the build of ohci-s3c2410.c
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix this sparse warning:
drivers/usb/host/oxu210hp-hcd.c:2687:42: warning: Using plain integer as NULL pointer
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB bus clock is usb-bus-host, so print the correct name in the
dev_err() statement if we cannot find it.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Remove the include of <mach/hardware.h>, as no definitions
from it are used by the OHCI driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lots of users are getting confused about the cp2101 driver. It really
does support more than just the cp2101 device, so rename it to cp210x to
try to prevent confusion.
Cc: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch lowers the logging priority of certain messages to prevent
users from flooding the log files.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the extended range of baud rates supported
by CP2102 and CP2103 devices described in SiLabs AN205. An additional
function cp2101_quantise_baudrate rounds the baud rate as per AN205
Table 1. A modification to the baud rate calculation removes a rounding
error, allowing the full range of baud rates to be used.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzfree() instead of memset() + kfree().
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1223) removes a bunch of unnecessary "inline"
annotations from the usbfs driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1221) changes the way usbcore reinitializes a device
following a reset or a reset-resume. Currently we call
usb_set_interface() for every interface in the active configuration;
this is to put the interface into the same altsetting as before the
reset and to make sure that the host's endpoint state matches the
device's endpoint state.
However, sending a Set-Interface request is a waste of time if an
interface was already in altsetting 0 before the reset, since it is
certainly in altsetting 0 afterward. In addition, many devices can't
handle Set-Interface requests -- they crash when they receive them.
So instead, the patch adds code to check each interface. If the
interface wasn't in altsetting 0 before the reset, we go head with the
Set-Interface request as before. But if it was then we skip sending
the Set-Interface request, and we clear out the host-side endpoint
state by calling usb_disable_interface() followed by
usb_enable_interface().
The patch also adds a couple of new comments to explain what's going
on.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
actual_length should also be a u32 and not a signed value. This patch
changes this field to be 'u32' to prevent any potential negative
conversion and comparison errors.
This triggered a few compiler warning messages when these fields were
being used with the min macro, so they have also been fixed up in this
patch.
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Roel Kluin pointed out that transfer_buffer_lengths in struct urb was
declared as an 'int'. This patch changes this field to be 'u32' to
prevent any potential negative conversion and comparison errors.
This triggered a few compiler warning messages when these fields were
being used with the min macro, so they have also been fixed up in this
patch.
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code in uhci-q.c doesn't have to use pseudo-negative values. I did
it that way because it was easy and because it would give the expected
output during debugging. But it doesn't have to work that way. Here's
another approach.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch disables USB regulators VUSB1V5, VUSB1V8, and VUSB3V1
when the USB cable is unplugged to reduce power consumption.
Added a depencency from twl4030 usb driver to TWL_REGULATOR.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an extension to the binary API so it reaches parity with
existing text API (so-called "1u"). The extension delivers additional data,
such as ISO descriptors and the interrupt interval.
Signed-Off-By: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following bug:
.plug ch341 usb serial port into a hub port;
.ch341 driver bound to the device and /dev/ttyUSB0 comes
.open /dev/ttyUSB0 by minicom and we can use the serial successfully
.suspend the ch341 usb serial device(such as: echo suspend > power/level)
.resume the ch341 usb serial device (such as: echo on > power/level)
.new port /dev/ttyUSB1 comes ,and the original /dev/ttyUSB0 still exists,
but is no longer usable by minicom
The patch adds suspend and resume callback to ch341 usb driver to prevent it
from unbinding during suspend. The /dev/ttyUSB0 is not released until being
closed, so /dev/ttyUSB1 comes after resume, and the original /dev/ttyUSB0 is
no longer usable by minicom. It is really a mess for a minicom user.
This patch also adds the reset_resume callback to make it usable after resuming
from STR or hibernation, for generally STR or hibernation will make the vbus
of root-hub lost.
Finally enable the driver's supports_autosuspend, for the device is in working
order with it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Partial support for DaVinci DM355, on the EVM board; peripheral
mode should work, once mainline merges DM355 support. Missing:
(a) renumbering the GPIO for DRVVBUS on the DM6446 EVM,
when DAVINCI_N_GPIO increases;
(b) disabling DM355_DEEPSLEEP.DRVVBUS_OVERRIDE so VBUS is
driven according to the ID signal, if cpu_is_..._dm355()
The new PHY control bits are ignored on DM6446.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Except on DaVinci, VBUS is now switched off as part of idling the
USB link (after a_wait_bcon) whenever a device is disconnected
from host. This is correct for OTG hosts, where either SRP or
an ID interrupt could turn VBUS on again.
However, for non-OTG hosts there's no way to turn VBUS on again,
so the host becomes unusable. And the procfs entry which once
allowed a manual workaround for this is now gone.
This patch adds an is_otg_enabled() check before scheduling the
switch-off timer in disconnect path, supporting a "classic host"
mode where SRP is unavailable.
[ dbrownell@users.sourceforge.net: tweak patch description ]
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct musb_read_fifosize() and musb_configure_ep0() functions
for the #ifndef BLACKFIN branch when the silicon uses static FIFO
configuration. (Most current silicon configures this controller
to use dynamic FIFO configuration; some parts from ST don't, like
the STM STA2062.)
Signed-off-by: Giuseppe GORGOGLIONE <giuseppe.gorgoglione@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes endpoint starvation issue when more than one bulk QH is
multiplexed on the reserved bulk RX endpoint, which is normal
for cases like serial and ethernet adapters.
This patch sets the NAK timeout interval for such QHs, and when
a timeout triggers the next QH will be scheduled. (This resembles
the bulk scheduling done in hardware by EHCI, OHCI, and UHCI.)
This scheme doesn't work for devices which are connected to a
high to full speed tree (transaction translator) as there is
no NAK timeout interrupt from the musb controller from such
devices.
Tested with PIO, Inventra DMA, CPPI DMA.
[ dbrownell@users.sourceforge.net: fold in start_urb() update;
clarify only for bulk RX; don't accidentally clear WZC bits ]
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current MUSB host code doesn't make use of all the available
FIFOs in for periodic transfers since it wrongly assumes the RX
and TX sides of any given hw_ep always share one FIFO.
Change: use 'in_qh' and 'out_qh' fields of the 'struct musb_hw_ep'
to check the endpoint's business; get rid of the now-unused 'periodic'
array in the 'struct musb'. Also optimize a loop induction variable
in the endpoint lookup code.
(Based on a previous patch from Ajay Kumar Gupta <ajay.gupta@ti.com>)
[ dbrownell@users.sourceforge.net: clarify description and origin
of this fix; whitespace ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To permit a userspace application to associate with WUSB devices
using numeric association, control transfers to unauthenticated WUSB
devices must be allowed.
This requires that wusbcore correctly sets the device state to
UNAUTHENTICATED, DEFAULT and ADDRESS and that control transfers can be
performed to UNAUTHENTICATED devices.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The lack of a MODULE_LICENSE macro in ums-* subdrivers prevented them
from loading. Needs to be applied after Alan Stern's usb-storage
subdriver separation patchset. Also added missing MODULE_DESCRIPTION and
MODULE_AUTHOR entries.
Signed-off-by: Maciej Grela <maciej.grela@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1217) converts usb-storage's onetouch subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1216) converts usb-storage's karma subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1215) converts usb-storage's alauda subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1214) converts usb-storage's jumpshot subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1213) converts usb-storage's datafab subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1212) converts usb-storage's freecom subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1211) converts usb-storage's shuttle_usbat subdriver
into a separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1210) converts usb-storage's cypress_atacb subdriver
into a separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1209) converts usb-storage's sddr55 subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1208) converts usb-storage's isd200 subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1207) converts usb-storage's sddr09 subdriver into a
separate module.
An unexpected complication arises because of DPCM devices, in which
one LUN uses the sddr09 transport and one uses the standard CB
transport. Since these devices can be used even when
USB_STORAGE_SDDR09 isn't configured, their entries in unusual_devs.h
require special treatment. If SDDR09 isn't configured then the
entries remain in unusual_devs.h; if it is then the entries are
present in unusual_sddr09.h instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1206) is the first step in converting usb-storage's
subdrivers into separate modules. It makes the following large-scale
changes:
Remove a bunch of unnecessary #ifdef's from usb_usual.h.
Not truly necessary, but it does clean things up.
Move the USB device-ID table (which is duplicated between
libusual and usb-storage) into its own source file,
usual-tables.c, and arrange for this to be linked with
either libusual or usb-storage according to whether
USB_LIBUSUAL is configured.
Add to usual-tables.c a new usb_usual_ignore_device()
function to detect whether a particular device needs to be
managed by a subdriver and not by the standard handlers
in usb-storage.
Export a whole bunch of functions in usb-storage, renaming
some of them because their names don't already begin with
"usb_stor_". These functions will be needed by the new
subdriver modules.
Split usb-storage's probe routine into two functions.
The subdrivers will call the probe1 routine, then fill in
their transport and protocol settings, and then call the
probe2 routine.
Take the default cases and error checking out of
get_transport() and get_protocol(), which run during
probe1, and instead put a check for invalid transport
or protocol values into the probe2 function.
Add a new probe routine to be used for standard devices,
i.e., those that don't need a subdriver. This new routine
checks whether the device should be ignored (because it
should be handled by ub or by a subdriver), and if not,
calls the probe1 and probe2 functions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With "nousb" cmdline booting, built-in serial drivers (ie. airecable)
will trigger kernel oops.
Indeed, if nousb, usb_serial_init will failed, and the usb serial bus type
will not be registerd, then usb_serial_register call driver_register
which try to register the driver to a not registered bus.
Here add usb_disabled() check in usb_serial_register to fix it.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix ehci printk formats:
drivers/usb/host/ehci-q.c:351: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
drivers/usb/host/ehci-q.c:351: warning: format '%d' expects type 'int', but argument 5 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver originally written by Qualcomm, but rewritten by me due to the
totally different coding style. Cleaned up the probe logic to make a
bit more sense, this is one wierd device. They could have prevented all
of this by just writing sane firmware for the modem.
Cc: Tamm Liu <tamml@qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to figure out what userspace programs are expecting from this
driver, so log them so we can try to get it right.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is for the Symbol 6608 barcode scanner in a fake "HID" mode.
Thanks to Dalibor Grgec for working with me to get this to start to work
properly.
Cc: Dalibor Grgec <dalibor.grgec@zemris.fer.hr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, the driver only supports PCI and PPC_OF but there are
boards like ARM RealView where this is a platform device. The patch adds
the necessary functions and registration to the isp1760-if.c file and
modifies the corresponding Makefile and Kconfig to be able to use this
driver even if PCI and PPC_OF are not enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch changes the prototype of the isp1760_register() function to use
predefined types like phys_addr_t and resource_size_t rather than u64
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1204) adds a software retry mechanism to ehci-hcd. It
gets invoked when the driver encounters transaction errors on an
asynchronous endpoint. On many systems, hardware deficiencies cause
such errors to occur if one device is unplugged while the host is
communicating with another device. With the patch, the failed
transactions are retried and generally succeed the second or third
time through.
This is based on code originally written by Koichiro Saito.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested by: Koichiro Saito <Saito.Koichiro@adniss.jp>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 64a87b24: [SCSI] Let scsi_cmnd->cmnd use request->cmd buffer
changed the scsi_eh_prep_cmnd logic by making it clear
the ->cmnd buffer. But the sat to cypress atacb translation supposed
the ->cmnd buffer wasn't modified.
This patch makes it set the ->cmnd buffer after scsi_eh_prep_cmnd call.
The problem and a fix was reported by Matthieu CASTET <castet.matthieu@free.fr>
It also removes all the hackery fiddling of scsi_cmnd and scsi_eh_save by
requesting from scsi_eh_prep_cmnd to prepare a read into ->sense_buffer,
which is much more suitable a buffer for HW transfers, then after the command
execution the regs read is copied into regs buffer before actual preparation
of sense_buffer.
Also fix an alien comment character to my utf-8 editor.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Cc: stable <stable@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Matthew Dharm <mdharm-kernel@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1205) moves timer_action() from ehci.h to ehci-hcd.c and
makes it out-of-line. Over the years it has grown too big to be inline
any more.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove old comments about USB_EHCI_HCD.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A USB-serial converter device is plugged into a system, and a process
opens it's device node. If the device is physically removed whilst the
process still has its device node open, then other processes can
sucessfully open the now non-existent device's node. I would expect
that open() on a device that has been physically removed should return
ENODEV.
This is manifesting itself with getty on my system. I do the following:
1. set up inittab to spawn getty on ttyUSB0, eg:
T1:23:respawn:/sbin/getty -L ttyUSB0 115200 vt100
2. Plug in USB-serial converter cable
3. Wait for a login prompt on a terminal program attached to the serial
cable
4. Login
5. Pull the USB-serial converter cable from the box
6. getty doesn't realise that ttyUSB0 no longer exists as /dev/ttyUSB0
can still be opened.
7. Re-insert the USB-serial converter cable
8. You should no longer get a login prompt over the serial cable, as
the the USB-serial cable now shows up as /dev/ttyUSB1, and getty is
trying to talk to /dev/ttyUSB0.
The attached patch will cause open("/dev/ttyUSB0", O_RDONLY) to return
ENODEV after the USB-serial converter has been pulled. The patch was
created against 2.6.28.1. I can supply it against something else if
needs be. It is fairly simple, so should be OK.
I am using a pl2303 device, although I don't think that makes any
difference.
From: James Woodcock <James.Woodcock@ACULAB.COM>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes the fallback to the generic method. It is cleaner to
explicitely request it. Introducing this was my mistake. This will
be solved by an explicit test and the driver being allowed to request
what it needs to be done upon resumption.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
338b67b0c1 removed the info macro and
replaced its uses with dev_info. This patch does so for
usb-skeleton.c, which was missed.
Signed-off-by: Matt Kraai <kraai@ftbfs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make lines about usb_storage depending on SCSI visible when configuring the
kernel in a 80x25 console
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This lets userspace determine what the state of the RTS line is, which
is what is needed to properly handle data flow for this device (it
raises RTS when there is data to be sent from it.)
Cc: Kees Stoop <kees.stoop@opticon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
NOP transceiver is used by all the usb transceiver which are mostly
autonomous and doesn't require any programming or which are built
into the usb ip itself.NOP transceiver only allocates the memory
for struct xceiv and calls otg_set_transceiver() so function call
to otg_get_transceiver() will return a valid transceiver.
NOP transceiver device should be registered by calling
usb_nop_xceiv_register() from platform files.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove some pointless messages from the FTDI serial driver;
I found these filling up syslog on one system. Also remove
a pointless "break" after a "return" in the same area.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing peaces here for the usb subsystem.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes use of the generic method if a serial driver provides
no implementation. This simplifies implementing suspend/resume support
in serial drivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This exports a symbol for usb_serial_generic_resume, so that modules can
use it.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes an unnecessary check for autoresume from the generic
resume method. The check has been obsoleted by the now delayed
increase of the usage counter which makes the error this check prevented
impossible. This change allows drivers which only use the bulk read URB
the use of the generic method even if they support autosuspend.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces a flag into the usb serial layer to tell drivers
that their URBs are killed due to suspension. That is necessary to let
drivers know whether they should report an error back.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Hi Greg,
this is for 2.6.30. Patches to use this in drivers are under development.
Regards
Oliver
With a postfix decrement count will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this does the standard support for suspend/resume for the opticon
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements suspend and resume methods for the
option driver. With my hardware I can even suspend the system
and keep up a connection for a short time.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Workaround of hw bug in IMX UDC.
This bug causes wrong handling of CFG_CHG interrupt.
Workaround is documented inline source code.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Samuel Ortiz