Commit Graph

49 Commits

Author SHA1 Message Date
Yoshihiro Shimoda ab330cf388 usb: renesas_usbhs: add support for USB-DMAC
Some Renesas SoCs have the USB-DMAC. It is able to terminate transfers
when a short packet is received, even if less bytes than the transfer
counter size have been received. Also, it is able to send a short
packet even if the packet size is not multiples of 8bytes.

Since the previous code has used the interruption of USBHS controller
when receiving packets even if this driver has used a dmac, a lot of
interruptions has happened. This patch will reduce such interruptions.

This patch allows to use the USB-DMAC on R-Car H2 and M2.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-13 10:41:19 -05:00
Sergei Shtylyov d7b3968dbc usb: renesas_usbhs: add OTG ID signal sensing
On the Renesas R8A7791 SoC based boards there's MAX3355 USB OTG chip and mini-AB
USB connector corresponding to USB port 0 driven either by EHCI/OHCI or  Renesas
USBHS gadget controller. And we'd like the host/gadget  drivers to work based on
the cable type connected. An 'extcon' driver for MAX3355 has been written, so we
only need to bind  to it via device tree which I'm doing in this patch.

(Perhaps, it would also make sense to use OTG HNP when the USBHS host mode is
active and a B-cable is connected but I don't have access to host-capable USBHS,
so  wouldn't be able to test it.)

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12 15:36:28 -06:00
Sergei Shtylyov 48ac1e5766 usb: renesas_usbhs: fix platform init error message
There is a typo ("prove" instead of "probe") in the error message printed when
the platform initialization fails. Replace that word with more fitting "init".

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12 12:13:27 -06:00
Sergei Shtylyov 368504c00a usb: renesas_usbhs: kill dead code in usbhs_probe()
usbhsc_drvcllbck_notify_hotplug() always returns 0, so it's rather pointless to
store and check its result for being < 0.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12 12:13:26 -06:00
Takeshi Kihara 04a5def3df usb: renesas_usbhs: gadget: fix the behavior of pullup
This patch fixes an issue that this driver always enable the D+ pullup
after it detected the VBUS connection even though this usb controller
can control the D+ pullup timing by software. So, this driver should
enable the D+ pullup after a gadget driver called usb_gadget_connect().

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-11-05 13:22:09 -06:00
Varka Bhadram 687f16b859 usb: renesas_usbhs: common: remove duplicate check on resource
Sanity check on resource happening with devm_ioremap_resource().

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-11-03 10:01:20 -06:00
Peter Chen b1cb07cdee usb: renesas_usbhs: delete unnecessary 'out of memory' messages
The memory subsystem has already had similar message for it.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-11-03 10:01:07 -06:00
Yoshihiro Shimoda b854100eda usb: renesas_usbhs: Add device tree support for R-Car H2 and M2
This driver supports other SoCs, but they need boards/Soc depend code.
So, this patch adds device tree support for R-Car H2 and M2 initially.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-09-05 10:59:27 -05:00
Ulrich Hecht 8ecef00fe1 usb: renesas_usbhs: add R-Car Gen. 2 init and power control
In preparation for DT conversion to reduce reliance on platform device
callbacks.

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-07-16 10:06:32 -05:00
Libo Chen c9a0552e8d usb: renesas_usbhs: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.

Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-08-27 21:35:23 -07:00
Jingoo Han ace0a5f947 usb: renesas: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-31 17:28:45 -07:00
Thierry Reding 148e11349b usb: Convert to devm_ioremap_resource()
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.

devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-22 11:41:58 -08:00
Bill Pemberton fb4e98ab63 usb: remove use of __devexit
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-21 13:27:17 -08:00
Bill Pemberton 7690417db5 usb: remove use of __devexit_p
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-21 13:27:16 -08:00
kuninori.morimoto.gx@renesas.com 4cd2f59987 usb: renesas_usbhs: gadget: add usb_gadget_ops :: pullup support
This patch adds usbhs_sys_function_pullup() to control
D+ line for USB function, and enabled pullup support on mod_gadget.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2012-10-16 13:09:50 +03:00
Kuninori Morimoto 58efc77c86 usb: renesas_usbhs: convert to devm_xxx()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-09-11 13:57:18 -07:00
Kuninori Morimoto 5b50d3b526 usb: renesas_usbhs: fixup resume method for autonomy mode
If renesas_usbhs is probed as autonomy mode,
phy reset should be called after power resumed,
and manual cold-plug should be called with slight delay.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-08-10 11:53:24 -07:00
Paul Bolle cc502bb741 renesas_usbhs: cleanup quoted includes
A few quoted includes start with a superfluous "./". Clean up those
quoted includes.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-06-05 10:15:25 +02:00
Shimoda, Yoshihiro 53069af3fa usb: renesas_usbhs: add IRQ resource decoding for IRQF_SHARED
In case of the SH7757, the irq number of USB module and SUDMAC
are the same. So, we have to set the IRQF_SHARED in such a case.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2012-01-24 11:32:56 +02:00
Greg Kroah-Hartman 121a8cdd79 Merge branch 'for-next/gadget' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
* 'for-next/gadget' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (50 commits)
  usb: renesas_usbhs: show error reason on usbhsh_urb_enqueu()
  usb: renesas_usbhs: add force packet remove method
  usb: renesas_usbhs: care usb_hcd_giveback_urb() status
  usb: renesas_usbhs: add usbhsh_is_running()
  usb: renesas_usbhs: disable attch irq after device attached
  usb: renesas_usbhs: care pipe sequence
  usb: renesas_usbhs: add usbhs_pipe_attach() method
  usb: renesas_usbhs: add usbhsh_endpoint_detach_all() for error case
  usb: renesas_usbhs: modify device attach method
  usb: renesas_usbhs: pop packet when urb dequeued
  usb: renesas_usbhs: add lost error value when enqueue
  usb: gadget: mv_udc: replace some debug info
  usb: gadget: mv_udc: refine suspend/resume function
  usb: gadget: mv_udc: refine the clock relative code
  usb: gadget: mv_udc: disable ISR when stopped
  usb: gadget: mv_udc: add otg relative code
  usb: gadget: Use kcalloc instead of kzalloc to allocate array
  usb: renesas_usbhs: remove the_controller_link
  usb: renesas_usbhs: add test-mode support
  usb: renesas_usbhs: call usbhsg_queue_pop() when pipe disable.
  ...
2011-12-13 09:37:40 -08:00
Kuninori Morimoto dfbb7f4fba usb: renesas_usbhs: add test-mode support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:45:20 +02:00
Kuninori Morimoto 3dd492686c usb: gadget: renesas_usbhs: modify function name of usbhs_set_device_xx()
it was device configuration setting function, not only speed.
This patch modify function name usbhs_set_device_speed() -> usbhs_set_device_config()

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:45:02 +02:00
Kuninori Morimoto b4fcea2a71 usb: gadget: renesas_usbhs: unified callback function
renesas_usbhs needs callback for notify hotplug.
but it were 2 methods which are almost same.
This patch unified these into one.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:44:59 +02:00
Kuninori Morimoto f1ee56a000 usb: gadget: renesas_usbhs: add platform power control function
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:44:58 +02:00
Kuninori Morimoto a49a88f108 usb: gadget: renesas_usbhs: tidyup the unit of detection_delay
detection_delay was assumed as msec

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:44:57 +02:00
Kuninori Morimoto 76190152fb usb: gadget: renesas_usbhs: tidyup usbhs_sys_clock_ctrl() was local function
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:44:56 +02:00
Kuninori Morimoto 3244a7b43f usb: gadget: renesas_usbhs: remove usbhs_sys_usb_ctrl()
usbhs_sys_usb_ctrl() can collect into usbhs_sys_host/function_ctrl().

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:44:47 +02:00
Kuninori Morimoto 2288e10993 usb: gadget: renesas_usbhs: remove usbhs_sys_hispeed_ctrl()
usbhs_sys_hispeed_ctrl() can collect into usbhs_sys_host/function_ctrl().

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-12-12 11:44:46 +02:00
Axel Lin cc27c96c2b usb: convert drivers/usb/* to use module_platform_driver()
This patch converts the drivers in drivers/usb/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Cc: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-28 06:48:32 +09:00
Kuninori Morimoto b7a8d17db9 usb: gadget: renesas_usbhs: fixup section mismatch warning
Fix up the following section mismatch warnings:

WARNING: drivers/usb/renesas_usbhs/renesas_usbhs.o(.text+0xf5d): Section
mismatch in reference from the function usbhs_mod_probe() to the function
.devinit.text:usbhs_mod_host_probe() The function usbhs_mod_probe() references
the function __devinit usbhs_mod_host_probe().  This is often because
usbhs_mod_probe lacks a __devinit annotation or the annotation of
usbhs_mod_host_probe is wrong.

WARNING: drivers/usb/renesas_usbhs/renesas_usbhs.o(.text+0xfd7): Section
mismatch in reference from the function usbhs_mod_probe() to the function
.devexit.text:usbhs_mod_host_remove() The function usbhs_mod_probe() references
a function in an exit section.  Often the function usbhs_mod_host_remove() has
valid usage outside the exit section and the fix is to remove the __devexit
annotation of usbhs_mod_host_remove.

WARNING: drivers/usb/renesas_usbhs/renesas_usbhs.o(.text+0x1005): Section
mismatch in reference from the function usbhs_mod_remove() to the function
.devexit.text:usbhs_mod_host_remove() The function usbhs_mod_remove()
references a function in an exit section.  Often the function
usbhs_mod_host_remove() has valid usage outside the exit section and the fix is
to remove the __devexit annotation of usbhs_mod_host_remove.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-14 11:51:23 -08:00
Kuninori Morimoto 482982062f usb: gadget: renesas_usbhs: bugfix: don't modify platform data
renesas_usbhs has default callback functions and settings.
And it tried overwrite to platform private data
if platform doesn't have them.
So, if renesas_usbhs was compiled as module,
it will be hung-up on 2nd insmod.
This patch fixup it.
Special thanks to Bastian

Reported-by: Bastian Hecht <hechtb@googlemail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13 20:41:53 +03:00
Kuninori Morimoto eb05191f6a usb: gadget: renesas_usbhs: add usbhs_set_device_speed() support for host
mod_host needs device speed setup function

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13 20:41:49 +03:00
Kuninori Morimoto a9be4a4562 usb: gadget: renesas_usbhs: make sure SOF packet sending-out control
It is enabled to set SOF packet output bit when USBRST bit was set.
And USBRST bit should be set 0 when SOF packet was output.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13 20:41:48 +03:00
Kuninori Morimoto f427eb64f4 usb: gadget: renesas_usbhs: support otg pin control
some renesas_usbhs device is supporting OTG external device interface.
In that device, it is necessary to control PWEN/EXTLP on DVSTCTR.
This patch support it.
But renesas_usbhs driver doesn't have OTG support for now.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13 20:41:47 +03:00
Kuninori Morimoto ef8bedb904 usb: gadget: renesas_usbhs: move usbhs_usbreq_get/set_val() to common.c
usbhs_usbreq_get/set_val() functions were in pipe.c file,
but it is irrelevant to pipe.
this patch move it to common.c

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13 20:41:40 +03:00
Kuninori Morimoto 75587f52c7 usb: gadget: renesas_usbhs: add usbhs_bus_get_speed()
current mod_gadget had got usb speed on
usbhsg_irq_dev_state() which is status change interrupt callback function.
And the usb speed data was included in its parameter.

But this style works for mod_gadget,
but doesn't work for mod_host which
isn't interrupted when device status was changed.

This patch add usbhs_bus_get_speed() to solve this issue.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13 20:41:38 +03:00
Kuninori Morimoto 258485d990 usb: gadget: renesas_usbhs: add bus control functions
this patch add DVSTCTR control function for HOST support

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13 20:41:38 +03:00
Kuninori Morimoto 11935de557 usb: gadget: renesas_usbhs: change usbhsc_bus_ctrl() to usbsc_set_buswait()
renesas_usbhs will have register DVSTCTR control function for HOST support.
This patch changes usbhsc_bus_ctrl() to usbsc_set_buswait(),
to remove DVSTCTR access from it,

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13 20:41:37 +03:00
Kuninori Morimoto ca8a282a53 usb: gadget: renesas_usbhs: add suspend/resume support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-10-13 20:40:00 +03:00
Kuninori Morimoto 233f519d27 usb: renesas_usbhs: fixup comment-out
This patch add/modify comment-out of renesas_usbhs.
On this process, usbhs_pkt_init was moved because it was placed under
usbhsf_null_handler which has no relationship it

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-07-08 14:57:12 -07:00
Kuninori Morimoto e73a9891b3 usb: renesas_usbhs: add DMAEngine support
USB DMA was installed on "normal DMAC" when SH7724 or older SuperH,
but the "USB-DMAC" was prepared on recent SuperH.
These 2 DMAC have a little bit different behavior.

This patch add DMAEngine code for "normal DMAC",
but it is still using PIO fifo.
The DMA fifo will be formally supported in the future.

You can enable DMA fifo by local fixup
usbhs_fifo_pio_push_handler -> usbhs_fifo_dma_push_handler
usbhs_fifo_pio_pop_handler  -> usbhs_fifo_dma_pop_handler
on usbhsg_ep_enable.

This DMAEngine was tested by g_file_storage on SH7724 Ecovec board

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-06-07 09:10:10 -07:00
Kuninori Morimoto d3af90a5e4 usb: renesas_usbhs: add usbhsf_fifo
renesas_usbhs has CFIFO/D0FIFO/D1FIFO.
But current renesas_usbhs is using CFIFO (for PIO) only for now.
The fifo selection method is needed for DMAEngine support.
This is a preparation for DMAEngine support

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-06-07 09:10:09 -07:00
Kuninori Morimoto 97f93227e6 usb: renesas_usbhs: fixup error processing on probe/remove
The error processing order was wrong.
This patch modify it.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-11 15:17:02 -07:00
Kuninori Morimoto b002ff6e26 usb: renesas_usbhs: add autonomy mode
Current renesas_usbhs was designed to save power when USB is not connected.
And it assumed platform uses callback to notify connection/disconnection
by external interrupt.

But some SuperH / platform board doesn't have such feature.

This patch adds autonomy mode which detect USB connection/disconnection
by internal interrupt.
But power will be always ON when autonomy mode is selected.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-29 17:24:35 -07:00
Kuninori Morimoto bc57381e63 usb: renesas_usbhs: use delayed_work instead of work_struct
This delay is used to overjump debounce.

And, this patch also move usbhsc_drvcllbck_notify_hotplug to global,
because it will be called from other files.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-29 17:24:34 -07:00
Kuninori Morimoto 6e267da8f1 usb: renesas_usbhs: add power control function
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-29 17:24:34 -07:00
Kuninori Morimoto 206dcc2cfe usb: renesas_usbhs: move pdev_to_priv to global
usbhs_pdev_to_priv function will be used in other files.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-29 17:24:33 -07:00
Kuninori Morimoto af32fe5113 usb: renesas_usbhs: remove callback when module removed.
The callback function which is called from platform must be removed
if module removed.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-29 17:24:32 -07:00
Kuninori Morimoto f1407d5c66 usb: renesas_usbhs: Add Renesas USBHS common code
Renesas SuperH has USBHS IP which can switch Host / Function.
This driver is designed so that Host / Function may dynamically change.
This patch add usb/renesas_usbhs and common code for SuperH USBHS.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-13 16:07:07 -07:00