Before this patch, the following error would sometimes occur after a
resume on pxa3xx:
/path/to/mm/memory.c:144: bad pmd 8040542e.
The problem was that a temporary page table mapping was being improperly
restored.
The PXA3xx resume code creates a temporary mapping of resume_turn_on_mmu
to avoid a prefetch abort. The pxa3xx_resume_after_mmu code requires
that the r1 register holding the address of this mapping not be
modified, however, resume_turn_on_mmu does modify it. It is mostly
correct in that r1 receives the base table address, but it may also
get other bits in 13:0. This results in pxa3xx_resume_after_mmu
restoring the original mapping to the wrong place, corrupting memory
and leaving the temporary mapping in place.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'spi' of git://git.linutronix.de/users/bigeasy/soda into spi/next
spi/pxa2xx: register driver properly
spi/pxa2xx: add support for shared IRQ handler
spi/pxa2xx: Use define for SSSR_TFL_MASK instead of plain numbers
arm/pxa2xx: reorgazine SSP and SPI header files
spi/pxa2xx: Add CE4100 support
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: pass of_node to spi device and set a parent device
flush_scheduled_work() is deprecated and scheduled to be removed.
Directly flush toggle_charger and sharpsl_bat works on suspend
instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Convert pxa to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ftrace requires sched_clock() to be notrace. Ensure that all
implementations are so marked. Also make sure that they include
linux/sched.h
Also ensure OMAP clocksource read functions are marked notrace as
they're used for sched_clock() too.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
The new FPGA firmware in Balloon3 uses different methods to control it's bus
control lines. In the new version, there are separate registers to set/clear
bus control lines. This patch updates affected places.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Tested on a Colibri Evaluation Board Rev.2.1 with a Colibri PXA310 module.
Signed-off-by: Bjorn Forsman <bjorn.forsman@gmail.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Rename colibri-pxa270-evalboard to colibri-evalboard as this board is used with
all Colibri modules.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This change -- pushing the MFP configuration back into Module files -- is
necessary because some evalboards can be used with multiple modules, where MFP
differs from module to module. Therefore MFP isn't board-specific, but
module-specific and the module should preconfigure itself for the board.
(And there is also the C preprocesor limitation and conflicting #define-s)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This driver also contains structures to eventually support PXA320. This is
planned to be added in a later patch.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Saarb platform is a handheld platform that supports Marvell PXA955 silicon.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The core of PXA955 is PJ4. Add new PJ4 support. And add new macro
CONFIG_PXA95x.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Define all IRQs in irqs.h. If some IRQs are sharing one IRQ number, define
them together. If some IRQs are sharing same name with different IRQ number,
define different IRQ.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
After introducing pxa930/pxa935 and new silicons, original cpuid rules
of XScale generation 3 can't fit new silicons. Now redefine the rule
of PXA3xx.
Only PXA300/PXA310/PXA320/PXA930/PXA935 are family members of PXA3xx.
PXA930/PXA935 are family members of PXA93x. PXA93x can be considered
as PXA3xx + CP.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This is important because on PXA3xx, the physical mapping of SMEMC registers
differs from the one on PXA2xx. In order to get PCMCIA working on both PXA2xx
and PXA320, the PCMCIA driver was adjusted accordingly as well.
Also, various places in the kernel had to be patched to use
__raw_read/__raw_write.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch introduces pxa2xx_map_io() and pxa3xx_map_io() to distinguish
between PXA25x/PXA27x and PXA3xx memory mapping.
Also, fixup for platforms broken after introducing pxa{25x,27x}_map_io()
and pxa3xx_map_io() is included.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The camera registers start and range are encoded into the platform
device, and are actually handled by ioremap()'ed, thus the mapping
in pxa_map_io() is not necessary.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Today more boards with arm cpu have selectable pci bus.
This patch makes this more scalable and remove line continuations in
Kconfig
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PXA-SPI driver relies on some files / defines which are arm specific
and are within the ARM tree. The CE4100 SoC which is x86 has also the
SPI core.
This patch moves the ssp and spi files from arm/mach-pxa and plat-pxa to
include/linux where the CE4100 can access them.
This move got verified by building the following defconfigs:
cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
raumfeld_defconfig magician_defconfig
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Reported-by: Rafael Gandolfi <kaillasse91@hotmail.fr>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.
as the code is identical at 99%
put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While at it, fix two checkpatch errors.
Several non-const struct instances constified by this patch were added after
the introduction of platform_suspend_ops in checkpatch.pl's list of "should
be const" structs (79404849e9).
Patch against mainline.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (505 commits)
[media] af9015: Fix max I2C message size when used with tda18271
[media] IR: initialize ir_raw_event in few more drivers
[media] Guard a divide in v4l1 compat layer
[media] imon: fix nomouse modprobe option
[media] imon: remove redundant change_protocol call
[media] imon: fix my egregious brown paper bag w/rdev/idev split
[media] cafe_ccic: Configure ov7670 correctly
[media] ov7670: allow configuration of image size, clock speed, and I/O method
[media] af9015: support for DigitalNow TinyTwin v3 [1f4d:9016]
[media] af9015: map DigitalNow TinyTwin v2 remote
[media] DigitalNow TinyTwin remote controller
[media] af9015: RC fixes and improvements
videodev2.h.xml: Update to reflect the latest changes at videodev2.h
[media] v4l: document new Bayer and monochrome pixel formats
[media] DocBook/v4l: Add missing formats used on gspca cpia1 and sn9c2028
[media] firedtv: add parameter to fake ca_system_ids in CA_INFO
[media] tm6000: fix a macro coding style issue
tm6000: Remove some ugly debug code
[media] Nova-S-Plus audio line input
[media] [RFC,1/1] V4L2: Use new CAP bits in existing RDS capable drivers
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, remove the module names hardcoded in platform data
and pass a NULL module name to those functions.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the soc_camera
platform data uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Move pin config to appropriate places and use it only if needed.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-By: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Up to now, only pxa2xx pcmcia driver is using the API. No other device driver
is using this API in PXA3xx or any other PXA silicons.
Restrict the scope only on pxa2xx and remove the implementation of pxa3xx. So
we can avoid oo much checking on cpuid after more pxa chips supported.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
get_clk_frequency_khz() is used in private cpufreq driver. In order to meet
the change of different pxa silicons, checking cpuid is introduced in
get_clk_frequency_khz(). While more pxa silicons are supported, the workload
of checking cpuid is higher.
So restrict the scope of get_clk_frequency_khz() on pxa2xx. Different pxa
silcions use different private cpufreq driver to avoid too much checking
on cpuid.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Bringup tavorevb3 development platform. UART and PMIC are enabled.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
mach-mmp utilizes pxa27x_keypad code so we need to move header to
platform pxa directory.
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
In case the pxa3xx-u2d driver isn't used, probing of ohci-pxa27x will cause an
ugly kernel crash (NULL pointer dereference in pxa3xx_u2d_start_hc(), because
struct u2d is NULL and clk_enable() call will crash the kernel, trying to access
it).
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
USB2.0 Device Controller (U2DC) which is found in Marvell PXA3xx.
U2DC supports both High and Full speed modes.
PXA320 and PXA300 U2DC supports only UTMI interface.
PXA310 U2DC supports only ULPI interface and has the OTG capability.
U2D Controller ULPI driver introduced in this patch supports only the
PXA310 USB Host via the ULPI.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* master.kernel.org:/home/rmk/linux-2.6-arm: (28 commits)
ARM: 6411/1: vexpress: set RAM latencies to 1 cycle for PL310 on ct-ca9x4 tile
ARM: 6409/1: davinci: map sram using MT_MEMORY_NONCACHED instead of MT_DEVICE
ARM: 6408/1: omap: Map only available sram memory
ARM: 6407/1: mmu: Setup MT_MEMORY and MT_MEMORY_NONCACHED L1 entries
ARM: pxa: remove pr_<level> uses of KERN_<level>
ARM: pxa168fb: clear enable bit when not active
ARM: pxa: fix cpu_is_pxa*() not expanding to zero when not configured
ARM: pxa168: fix corrected reset vector
ARM: pxa: Use PIO for PI2C communication on Palm27x
ARM: pxa: Fix Vpac270 gpio_power for MMC
ARM: 6401/1: plug a race in the alignment trap handler
ARM: 6406/1: at91sam9g45: fix i2c bus speed
leds: leds-ns2: fix locking
ARM: dove: fix __io() definition to use bus based offset
dmaengine: fix interrupt clearing for mv_xor
ARM: kirkwood: Unbreak PCIe I/O port
ARM: Fix build error when using KCONFIG_CONFIG
ARM: 6383/1: Implement phys_mem_access_prot() to avoid attributes aliasing
ARM: 6400/1: at91: fix arch_gettimeoffset fallout
ARM: 6398/1: add proc info for ARM11MPCore/Cortex-A9 from ARM
...
When CONFIG_PXA3xx is not selected, cpu_is_pxa3xx() doesn't expand to
zero, which in some places doesn't result in correct optimization.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Reported-and-tested-by: Marek Vasut <marek.vasut@gmail.com>
This fixes the regression caused by the commit 6fee48cd33
("dma-mapping: arm: use generic pci_set_dma_mask and
pci_set_consistent_dma_mask").
ARM needs to clip the dma coherent mask for dmabounce devices. This
restores the old trick.
Note that strictly speaking, the DMA API doesn't allow architectures to do
such but I'm not sure it's worth adding the new API to set the dma mask
that allows architectures to clip it.
Reported-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to PXA3xx Processor Family Developer Manuall Vol1. section
"Pin Descriptions and Control", PXA30x and PXA31x Processor Alternate
Function Table shows the Alt FN 0 for GPIO51 is CI_HSYNC and for GPIO52
is CI_VSYNC. This patch fixes the MFP defines and also corrects the
order of MFD defines.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This is causing section mismatches when linking, as cpufreq_driver->init()
is not supposed to be in init section.
Reported-by: Tomáš 'Sleep_Walker' Čech <sleep_walker@suse.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Fairly simple conflicts, the most serious ones are the i.MX ones which I
suspect now need another rename.
Conflicts:
arch/arm/mach-mx2/clock_imx27.c
arch/arm/mach-mx2/devices.c
arch/arm/mach-omap2/board-rx51-peripherals.c
arch/arm/mach-omap2/board-zoom2.c
sound/soc/fsl/mpc5200_dma.c
sound/soc/fsl/mpc5200_dma.h
sound/soc/fsl/mpc8610_hpcd.c
sound/soc/pxa/spitz.c
This patch extends the ASoC API to allow sound cards to have more than one
CODEC and more than one platform DMA controller. This is achieved by dividing
some current ASoC structures that contain both driver data and device data into
structures that only either contain device data or driver data. i.e.
struct snd_soc_codec ---> struct snd_soc_codec (device data)
+-> struct snd_soc_codec_driver (driver data)
struct snd_soc_platform ---> struct snd_soc_platform (device data)
+-> struct snd_soc_platform_driver (driver data)
struct snd_soc_dai ---> struct snd_soc_dai (device data)
+-> struct snd_soc_dai_driver (driver data)
struct snd_soc_device ---> deleted
This now allows ASoC to be more tightly aligned with the Linux driver model and
also means that every ASoC codec, platform and (platform) DAI is a kernel
device. ASoC component private data is now stored as device private data.
The ASoC sound card struct snd_soc_card has also been updated to store lists
of it's components rather than a pointer to a codec and platform. The PCM
runtime struct soc_pcm_runtime now has pointers to all its components.
This patch adds DAPM support for ASoC multi-component and removes struct
snd_soc_socdev from DAPM core. All DAPM calls are now made on a card, codec
or runtime PCM level basis rather than using snd_soc_socdev.
Other notable multi-component changes:-
* Stream operations now de-reference less structures.
* close_delayed work() now runs on a DAI basis rather than looping all DAIs
in a card.
* PM suspend()/resume() operations can now handle N CODECs and Platforms
per sound card.
* Added soc_bind_dai_link() to bind the component devices to the sound card.
* Added soc_dai_link_probe() and soc_dai_link_remove() to probe and remove
DAI link components.
* sysfs entries can now be registered per component per card.
* snd_soc_new_pcms() functionailty rolled into dai_link_probe().
* snd_soc_register_codec() now does all the codec list and mutex init.
This patch changes the probe() and remove() of the CODEC drivers as follows:-
o Make CODEC driver a platform driver
o Moved all struct snd_soc_codec list, mutex, etc initialiasation to core.
o Removed all static codec pointers (drivers now support > 1 codec dev)
o snd_soc_register_pcms() now done by core.
o snd_soc_register_dai() folded into snd_soc_register_codec().
CS4270 portions:
Acked-by: Timur Tabi <timur@freescale.com>
Some TLV320aic23 and Cirrus platform fixes.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
TI CODEC and OMAP fixes
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Samsung platform and misc fixes :-
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
MPC8610 and PPC fixes.
Signed-off-by: Timur Tabi <timur@freescale.com>
i.MX fixes and some core fixes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
J4740 platform fixes:-
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
CC: Tony Lindgren <tony@atomide.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: Kuninori Morimoto <morimoto.kuninori@renesas.com>
CC: Daniel Gloeckner <dg@emlix.com>
CC: Manuel Lauss <mano@roarinelk.homelinux.net>
CC: Mike Frysinger <vapier.adi@gmail.com>
CC: Arnaud Patard <apatard@mandriva.com>
CC: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
ffuart is available on cm-x300 only with pxa300.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: stable <stable@kernel.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Improve formating so checkpatch passes. Also, change some function and variable
names to make the naming consistent.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This huge patch mostly shuffles code. The spitz.c file contained terrible mess
and needed a cleanup, here it is:
1) Made every part modular, components are not built in if not selected.
2) Removed loads of preprocessor goo, mostly "#ifdef MACH_AKITA .... #endif" and
similar code. The kernel size will grow by a few kb now, but the file is much
more readable.
3) Reworked SD/CF power setting function and made it reentrant.
4) Add ISL6271A regulator support
5) Correctly register WM8750
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This contains common code for Palm LD, TX, T5, Z72, Treo680, Centro
This code also adds PMIC support for all the devices,
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
READ_GPIO_BIT() is no way generic by accessing GPIO registers directly,
replace it with gpio_get_value().
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
IDE_PXA_CF doesn't exist in Kconfig, therefore removing all references
for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Juergen Schindele <schindele@nentec.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
XSCALE_CACHE_ERRATA doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
CORGI_SSP_DEPRECATED doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
ARCH_GUMSTIX_ORIG doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
BACKLIGHT_CORGI was later renamed to BACKLIGHT_GENERIC and has not been
used since then. As it's now safe to completely transition to LCD_CORGI
driver, which incorprates both the LCD and backlight device.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch:
1) Simpifies the DRI recomputation routine by pulling out the common code
2) Fixes a bug in PXA27x DRI recomputation caused by incorrect parenthesis
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The latest PXA3xx DM has enabled 312MHz for the HSS bus,
which allows x24 multiplier.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
With kexec-based kernel boot loader on Zaurus, the machine ID is
actually correctly passed, and head-sharpsl.S is not necessary.
Introduce PXA_SHARPSL_DETECT_MACH_ID, and include head-sharpsl.S
only when that's explicitly enabled.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
1. TOSA related un-hidden options moved to right under MACH_TOSA
2. SHARPSL_PM related hidden options moved to the end of Kconfig
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Not tested and enabled on MMP at this moment, and since the IRQ
is different from mach-pxa, I'd prefer to move the PMU device
back into mach-pxa/. Will introduce the PMU device to MMP once
it's enabled and tested.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
pxa3xx cpu needs the irq type setup to be able to
wakeup from low power mode on IRQ_WAKEUPx events.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This file is scheduled for removal, therefore fix all devices that use this
file to use the suggested wm97xx.h and pass platform data properly.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Tomas Cech <sleep_walker@suse.cz>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Move the platform specific bootmem memory reservations out of
arch/arm/mm/mmu.c into their respective platform files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Everything should now be using sparsemem rather than discontigmem, so
remove the code supporting discontigmem from ARM.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The wrong CONFIG defines were checked, and the <mach/audio.h>
include was missing
Signed-off-by: pieter <p.grimmerink@inepro.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch:
1) Simpifies the DRI recomputation routine by pulling out the common code
2) Fixes a bug in PXA27x DRI recomputation caused by incorrect parenthesis
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch registers the WM8750 codec on a proper place on the ZipitZ2
machine after the WM8750 driver was converted to new API.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for the AER915 battery chip into Zipit Z2
platform file.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Use the resume callback of the pda_power supply framework to check for a
'charge finished' event that might have occured during the sleep phase.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This is support for custom design based on Toradex Colibri PXA270 CPU card.
Initial patch was by Pavel Revak.
[daniel - rebased the code to follow the module/board split]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Pavel Revak <palo@bielyvlk.sk>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Follow the idea of several MX31 based boards and split code that is
related to the module from code that is baseboard specific. This makes
adding new base board support easier, while avoiding code duplication.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch just moves code around and polishes it. Also, compile in only
selected pieces of hardware.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for the MAX1587A used on Voipac PXA270 board.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds a driver for a harddrive attached to PXA address and data bus.
Unlike pata_platform, this driver allows usage of PXA DMA controller, making the
transmission speed 3x higher.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since commit a48c24a696, the
camera is not working anymore.
After the v4l2 migration, the mt9m111 camera board
information was not passed to the i2c layer anymore, but
stored for future use of v4l2 (through soc_camera).
Because mioa701_i2c_devices[] was tagged as "__initdata",
and because after the v4l2 migration, the new structure
"iclink" references it, the mt9m111 driver is not probed
anymore, as part of "iclink" is not valid (discarded after
kernel init).
Although there is not compilation error, nor runtime oops,
this patch restores a working camera on the mioa701 board.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch fixes flash layout to it's final version. Also, I fixed the
authorship information of this file as it's been totally reworked since Ken
released his last version.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch registers the WM8750 codec on a proper place on the SPITZ machine
after the WM8750 driver was converted to new API.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
delay_detect in HZ is confusing, convert it to be millisecond based. And
thus remove those unnecessary call to msecs_to_jiffies() at runtime for
this field. Other constants are converted assuming HZ == 100, which are
basically true for those platforms.
The assignment in csb726.c was incorrect, and is fixed in this patch as
a result.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Daniel Mack <daniel@caiaq.de>
This patch removes write to UP2OCR[DMSTATE] (ex-UP2OCR_DPPUBE) which is invalid
on PXA270C5 and later.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The touchscreen GPIO IRQ was used as a magic number. Define it properly in the
board header file. This is a simple cleanup patch.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for the on-board IDE channel. I tested this with a CDROM
connected over 2.5-3.5 IDE reduction with external power supplied to the CDROM.
This was not tested with the Voipac 270-HDD-000 (official Voipac HDD module),
but I expect no problems.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This adds support for the UCB1400 touchscreen found in the VPAC270 device.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
NOTE:
I wasn't able to get it running without reseting the HXOE (so it's there based
on my tests with the hardware). I'll have to investigate it properly when I have
more time.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds basic support for the Voipac PXA270 SBC.
The device consists of the following hardware:
- PXA270 @ 520 MHz
- 256MB RAM (sparsemem, 2*128MB regions)
- 64MB NOR flash
- 640x480 LCD
- Ports: 2xUHC, 1xUDC, 1xPCMCIA, VGA, FFUART, 2xPS2, Speaker, MIC
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for the Zipit Z2. The parts missing from this
patch are the battery support, SPI driver for the LCD and support for
the Silicon Serial ID chip.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
CM-X300 bootloader passes DRAM configuration information in ATAGS,
however, the first memory bank is reported at actual physical address 0x8000000.
Use the configuration information supplied by the bootloader and
cope with the necessity to have PHYS_ADDR=0xa0000000.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Tosa is now able to use generic matrix keypad driver instead of the deprecated
tosakbd.c, where CONFIG_KEYBOARD_TOSA_USE_EXT_KEYCODES is still useful. Move
it to mach/Kconfig.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
REVISIT: change to GPIO18 is ugly, need to make sure whether that's
really necessary - GPIO18_RDY as an VLIO input signal - we don't
normally need to do such kind of trick during low power mode.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Some pins are expected to keep their last level during suspend, and
introduce MFP_LPM_KEEP_OUTPUT for this.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
PXA_SSP is actually used by drivers like drivers/spi/pxa2xx_spi.c and
sound/soc/pxa/pxa-ssp.c, not by boards. Remove those incorrect 'select'
from Kconfig and make SOC_PXA_SSP to select.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The previous definitions of SSCR0_SCR and SSCR0_SerClkDiv() prevented
them being used simultaneously when supporting multiple PXA SoCs, esp.
in drivers/spi/pxa2xx_spi.c, make them correct.
The change from SSCR0_SerClkDiv(2) to SSCR0_SCR(2), will make the result
a little bit different in pxa2xx_spi_probe(), however, since that's only
used as a default initialization value, it's acceptable.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The only use of corgi_ssp.c is corgi_ts.c, which is now deprecated
and removed. Remove corgi_ssp.c and corgi_lcd.c and their relevant
function declarations and data structures.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Pavel Machek <pavel@ucw.cz>
The use of mfp_cfg_t causes build errors without including <mach/mfp.h>.
CC: stable@kernel.org
CC: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Jakob Viketoft <jakob.viketoft@bitsim.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
On/Off contains slash in the name, which causes warning during boot.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Fix the wrong variable used in cpu_is_pxa950().
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The timeout value is in jiffies, so it should be using HZ, not a plain
number. Assume with HZ=100 '100' means 1s here and adapt accordingly.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Marc Zyngier <maz@misterjones.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Shen <paul.shen@marvell.com>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
"on/off button" was recently renamed to remove the slash character.
Follow that change in the pin polarity detection as well.
While at it, fix another cosmetic coding style flaw as well.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Chip model can now be selected directly by matching the modalias name
(instead of filling the .model field in platform_data), and allows the
module to be auto-loaded. Previous behaviour is of course still supported.
Convert the two in-tree users to this feature (icontrol & zeus).
Tested on an Zeus platform (mcp2515).
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Christian Pellegrin <chripell@fsfe.org>
Cc: Edwin Peer <epeer@tmtservices.co.za>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This fixes a warning when booting 2.6.34-rc2:
[ 26.619814] ------------[ cut here ]------------
[ 26.624604] WARNING: at fs/proc/generic.c:316 __xlate_proc_name+0xac/0xc0()
[ 26.631555] name 'on/off button'
[ 26.634753] Modules linked in:
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
sharpsl_pm.c actually depends on max1111 driver being built-in when
not using legacy ssp code.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Due to commit:
5de813b ARM: Eliminate decompressor -Dstatic= PIC hack
The data section will be discarded for the decompressor, thus move the
static variables into BSS section by initializing them at run time.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (370 commits)
ARM: S3C2443: Add set_rate and round_rate calls for armdiv clock
ARM: S3C2443: Remove #if 0 for clk_mpll
ARM: S3C2443: Update notes on MPLLREF clock
ARM: S3C2443: Further clksrc-clk conversions
ARM: S3C2443: Change to using plat-samsung clksrc-clk implementation
USB: Fix s3c-hsotg build following Samsung platform header moves
ARM: S3C64XX: Reintroduce unconditional build of audio device
ARM: 5961/1: ux500: fix CLKRST addresses
ARM: 5977/1: arm: Enable backtrace printing on oops when PC is corrupted
ASoC: Fix S3C64xx IIS driver for Samsung header reorg
ARM: S3C2440: Fix plat-s3c24xx move of s3c2440/s3c2442 support
[ARM] pxa: fix typo in mxm8x10.h
[ARM] pxa/raumfeld: set GPIO drive bits for LED pins
[ARM] pxa/zeus: Add support for mcp2515 CAN bus
[ARM] pxa/zeus: Add support for onboard max6369 watchdog
[ARM] pxa/zeus: Add Eurotech as the manufacturer
[ARM] pxa/zeus: Correct the USB host initialisation flags
[ARM] pxa/zeus: Allow usage of 8250-compatible UART in uncompress
[ARM] pxa: refactor uncompress.h for non-PXA uarts
[ARM] mmp2: fix incorrect calling of chip->mask_ack() for 2nd level cascaded IRQs
...
This converts arm to the generic pci_set_dma_mask and
pci_set_consistent_dma_mask (removes HAVE_ARCH_PCI_SET_DMA_MASK for
dmabounce).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Looked-over-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update broadsheetfb to add support for multiple panel types. The 3.7" and
6" are known to work but the 9.7" is untested due to lack of hardware.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A pointer to a probe callback is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Cc: Paul Sokolovsky <pmiscml@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Set GPIO bits to pull the pins connected to LEDs for lower power mode.
We want all LEDs off when devices are in suspend.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Amit Walambe <amit.walambe@eurotech.com>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Amit Walambe <amit.walambe@eurotech.com>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Zeus console port is wired to a 8250-compatible device (pxa UARTs are
reserved to other uses). This patch allows such a configuration in the
uncompress sequence.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The original patch came from Marc Zyngier where support of 8250-compatible
UART is required to show the uncompress information. Modified a little bit
here, including changes below:
1. #include <mach/regs-uart.h> is actually not necessary
2. introduced uart_{read,write}() for different base and shift
3. introduced uart_is_enabled() and assumed enabled always for
non-PXA uarts
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Marc Zyngier <maz@misterjones.org>
Also remove a trailing whitespace while being there.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Add some safety check for CONFIG_PM around zeus_power_off(). Without
it linking can fail like this:
arch/arm/mach-pxa/built-in.o: In function `zeus_power_off':
e800.c:(.text+0x2bc8): undefined reference to `pxa27x_cpu_suspend'
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
IRQ_LOCOMO_* are never used elsewhere, remove these definitions. As well
as the cascade of these IRQs. IRQ_LOCOMO_*_BASE changed to IRQ_LOCOMO_*.
IRQ_LOCOMO_LT and IRQ_LOCOMO_SPI are likely to be used in a same way as
IRQ_LOCOMO_KEY.
IRQ_LOCOMO_GPIO and the demultiplex handler should really be living
somewhere else.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
It is not necessary and is over-complicated for IRQ_LOCOMO_KEY to
be a cascaded IRQ of IRQ_LOCOMO_KEY_BASE. Removed and introduced
locomokbd_{open,close} for masking/unmasking of the keyboard IRQ.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Missing AC97 pin configurations are added where pxa_set_ac97_info() are
called for all pxa25x/pxa27x platforms. Where no exact configuration is
provided, use the default as in sound/arm/pxa2xx-ac97-lib.c
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This is really pxa27x specific and should be kept in pxa27x.c. With this
newly introduced function, the original set_resetgpio_mode() is deprecated.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
pxa_camera init() callback is sometimes abused to setup MFP for PXA CIF, or
even to request GPIOs to be used by the camera *sensor*. These initializations
can be performed statically in machine init functions.
The current semantics for this init() callback is ambiguous anyways, it is
invoked in pxa_camera_activate(), hence at device node open, but its users use
it like a generic initialization to be done at module init time (configure
MFP, request GPIOs for *sensor* control).
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Makes it consistent with VMALLOC_START
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most machine classes want some way to register a block of clk_lookup
structures, and most do it by implementing a clks_register() type
function which walks an array, or by open-coding a loop.
Consolidate all this into clkdev_add_table().
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These functions are called with irqs already off. This commit removes
the calls to raw_local_irq_save and raw_local_irq_restore on platforms
that don't have to use a shared interrupt for their timekeeping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
There is no such GPIO for udc vbus sensing, put '-1' instead of default
'0' as '0' does mean a valid GPIO.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Somehow, strange characters made their way zaurus gpio .desc
fields. Fix it.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Stanislav Brabec <utx@penguin.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
PXA mmc host driver supports card detect, read only and power gpio pin
setting already. Zylonite platform driver needn't implement this any more.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
DM9000s on Zeus sometime fail under heavy load.
Relaxing the timings a bit seems to be of a great help.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This has to be selected, otherwise some peripherals don't get initialized.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This adds support for Raumfeld's 'Controller', 'Connector', 'Speaker S'
and 'Speaker M' devices. They're all based on PXA303 SoCs.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The Arcom Zeus CF slot requires the same kind of support as the Viper.
To avoid code duplication, introduce a platform device that abstracts
the differences.
This also allows for the removal of the ugly export of viper_cf_rst().
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Commit e2c509c7e6 ([ARM] pxa/hx4700: use platform_lcd driver)
missed to actually register platform device for LCD.
It causes following GCC warning:
arch/arm/mach-pxa/hx4700.c:553: warning: 'hx4700_lcd' defined but not used
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
pxa_camera init() is ambiguous, it's better to configure PXA CIF pins
statically in machine init function.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
pxa_camera init() is ambiguous, it's better to statically configure the sensor.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Aric D. Blumer