Since FCoE isn't supported by the i40e products there isn't much point in
carrying around code that will always evaluate to false. This patch goes
through and strips out the code in several spots so that we don't go around
carrying variables and/or code that is always going to evaluate to false or
0.
Change-ID: I39d1d779c66c638b75525839db2b6208fdc809d7
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Looking over the code for FCoE it looks like the Rx path has been broken at
least since the last major Rx refactor almost a year ago. It seems like
FCoE isn't supported for any of the Fortville/Fortpark hardware so there
isn't much point in carrying the code around, especially if it is broken
and untested.
Change-ID: I892de8fa551cb129ce2361e738ff82ce55fa229e
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a minor clean-up to make the i40e/i40evf process_skb_fields
function look a little more like what we have in igb. The Rx checksum
function called out a need for skb->protocol but I can't see where it
actually needs it. I am assuming this is something that was likely
refactored out some time ago as the Rx checksum code has gone through a few
rewrites.
Change-ID: I0b4668a34d90b61b66ded7c7c26e19a3e2d06251
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removed no longer needed delays. At preproduction stage those delays were
needed but now these delays are not needed.
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
First, this patch eliminates IOMMU DMAR Faults caused by VF hardware.
This is done by enabling VF hardware only after VSI resources are
freed. Otherwise, hardware could DMA into memory that is (or just has
been) being freed.
Then, the VF driver is activated only after VSI resources have been
reallocated. That's because the VF driver can request resources
immediately after it's activated. So they need to be ready at that
point.
The second race condition happens when the OS initiates a VF reset,
and then before it's finished modifies VF's settings by changing its
MAC, VLAN ID, bandwidth allocation, anti-spoof checking, etc. These
functions needed to be blocked while VF is undergoing reset. Otherwise,
they could operate on data structures that had just been freed or not
yet fully initialized.
Change-ID: I43ba5a7ae2c9a1cce3911611ffc4598ae33ae3ff
Signed-off-by: Robert Konklewski <robertx.konklewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to reset skb back to NULL when we have freed it in the Rx cleanup
path. I found one spot where this wasn't occurring so this patch fixes it.
Change-ID: Iaca68934200732cd4a63eb0bd83b539c95f8c4dd
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in the driver where the calculation of the
RSS size was not taking into account the number of traffic classes
enabled. This patch factors in the traffic classes both in
the initial configuration of the table as well as reconfiguration.
Change-ID: I34dcd345ce52faf1d6b9614bea28d450cfd5f621
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the driver code so that we do bulk updates of the page reference
count instead of just incrementing it by one reference at a time. The
advantage to doing this is that we cut down on atomic operations and
this in turn should give us a slight improvement in cycles per packet.
In addition if we eventually move this over to using build_skb the gains
will be more noticeable.
I also found and fixed a store forwarding stall from where we were
assigning "*new_buff = *old_buff". By breaking it up into individual
copies we can avoid this and as a result the performance is slightly
improved.
Change-ID: I1d3880dece4133eca3c32423b04a5467321ccc52
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When testing the epoll w/ busy poll code I found that I could get into a
state where the i40e driver had q_vectors w/ active NAPI that had no rings.
This was resulting in a divide by zero error. To correct it I am updating
the driver code so that we only support NAPI on q_vectors that have 1 or
more rings allocated to them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a complex if->continue->else->break construction in
i40e_next_filter. We can simply use hlist_for_each_entry_continue
instead. This drops a lot of confusing code. The resulting code is much
easier to understand the intention, and follows the more normal pattern
for using hlist loops. We could have also used a break with a "return
next" at the end of the function, instead of return NULL, but the
current implementation is explicitly clear that when you reach the end
of the loop you get a NULL value. The alternative construction is less
clear since the reader would have to know that next is NULL at the end
of the loop.
Change-Id: Ife74ca451dd79d7f0d93c672bd42092d324d4a03
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable FDir filters for SCTPv4 packets using the ethtool ntuple
interface to enable filters. The ethtool API does not allow masking on
the verification tag.
Change-Id: I093e88a8143994c7e6f4b7b17a0bd5cf861d18e4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for flexible payloads passed via ethtool user-def field.
This support is somewhat limited due to hardware design. The input set
can only be programmed once per filter type, and the flexible offset is
part of this filter input set. This means that the user cannot program
both a regular and a flexible filter at the same time for a given flow
type. Additionally, the user may not program two flexible filters of the
same flow type with different offsets, although they are allowed to
configure different values at that offset location.
We support a single flexible word (2byte) value per protocol type, and
we handle the FLX_PIT register using a list of flexible entries so that
each flow type may be configured separately.
Due to hardware implementation, the flexible data is offset from the
start of the packet payload, and thus may not be in part of the header
data. For this reason, the offset provided by the user defined data is
interpreted as a byte offset from the start of the matching payload.
Previous implementations have tried to represent the offset as from the
start of the frame, but this is not feasible because header sizes may
change due to options.
Change-Id: 36ed27995e97de63f9aea5ade5778ff038d6f811
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to parse the user-def field into a data structure format. This
code is intended to allow future extensions of the user-def field by
keeping all code that actually reads and writes the field into a single
location. This ensures that we do not litter the driver with references
to the user-def field and minimizes the amount of bitwise operations we
need to do on the data.
Add code which parses the lower 32bits into a flexible word and its
offset. This will be used in a future patch to enable flexible filters
which can match on some arbitrary data in the packet payload. For now,
we just return -EOPNOTSUPP when this is used.
Add code to fill in the user-def field when reporting the filter back,
even though we don't actually implement any user-def fields yet.
Additionally, ensure that we mask the extended FLOW_EXT bit from the
flow_type now that we will be accepting filters which have the FLOW_EXT
bit set (and thus make use of the user-def field).
Change-Id: I238845035c179380a347baa8db8223304f5f6dd7
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Do not use the user-def field for determining the VF target. Instead,
similar to ixgbe, partition the ring_cookie value into 8bits of VF
index, along with 32bits of queue number. This is better than using the
user-def field, because it leaves the field open for extension in
a future patch which will enable flexible data. Also, this matches with
convention used by ixgbe and other drivers.
Change-Id: Ie36745186d817216b12f0313b99ec95cb8a9130c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support to detect when we can update the input set for each flow
type.
Because the hardware only supports a single input set for all flows of
that matching type, the driver shall only allow the input set to change
if there are no other configured filters for that flow type.
Thus, the first filter added for each flow type is allowed to change the
input set, and all future filters must match the same input set. Display
a diagnostic message whenever the filter input set changes, and
a warning whenever a filter cannot be accepted because it does not match
the configured input set.
Change-Id: Ic22e1c267ae37518bb036aca4a5694681449f283
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ensure that the default input set is correctly reprogrammed when
cleaning up after disabling flow director support. This ensures that the
programmed value will be in a clean state.
Although we do not yet have support for SCTPv4 filters, a future patch
will add support for this protocol, so we will correctly restore the
SCTPv4 input set here as well. Note that strictly speaking the default
hardware value for SCTP includes matching the verification tag. However,
the ethtool API does not have support for specifying this value, so
there is no reason to keep the verification field enabled.
This patch is the next step on the way to enabling partial tuple filters
which will be implemented in a following patch.
Change-Id: Ic22e1c267ae37518bb036aca4a5694681449f283
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Do not assume that hardware has been programmed with the default mask,
but instead read the input set registers to determine what is currently
programmed. This ensures that all programmed filters match exactly how
the hardware will interpret them, avoiding confusion regarding filter
behavior.
This sets the initial ground-work for allowing custom input sets where
some fields are disabled. A future patch will fully implement this
feature.
Instead of using bitwise negation, we'll just explicitly check for the
correct value. The use of htonl and htons are used to silence sparse
warnings. The compiler should be able to handle the constant value and
avoid actually performing a byteswap.
Change-Id: I3d8db46cb28ea0afdaac8c5b31a2bfb90e3a4102
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current implementation of .set_rxnfc does not properly read the mask
field for filter entries. This results in incorrect driver behavior, as
we do not reject filters which have masks set to ignore some fields. The
current implementation simply assumes that every part of the tuple or
"input set" is specified. This results in filters not behaving as
expected, and not working correctly.
As a first step in supporting some partial filters, add code which
checks the mask fields and rejects any filters which do not have an
acceptable mask. For now, we just assume that all fields must be set.
This will get the driver one step towards allowing some partial filters.
At a minimum, the ethtool commands which previously installed filters
that would not function will now return a non-zero exit code indicating
failure instead.
We should now be meeting the minimum requirements of the .set_rxnfc API,
by ensuring that all filters we program have a valid mask value for each
field.
Finally, add code to report the mask correctly so that the ethtool
command properly reports the mask to the user.
Note that the typecast to (__be16) when checking source and destination
port masks is required because the ~ bitwise negation operator does not
correctly handle variables other than integer size.
Change-Id: Ia020149e07c87aa3fcec7b2283621b887ef0546f
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The previous code relied on i40e_match_fdir_input_set to determine when
determining whether to free the old filter. Change this code so that we
simply unconditionally delete the old filter, even if it's identical to
the new filter. This ensures that we don't leak any memory, and that we
always update the filters as expected.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Although we will fail the filter later due to checking flow_type which
will have a bogus invalid type, it is possible future refactoring will
remove this hidden failure case. Avoid a possible issue in the future by
explicitly checking the flow type at the start.
Change-Id: Ia98eb26f7b93ccbe38c7141e8f203ef496fc6598
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for adding code to properly check the mask values, we
will need to know the number of active filters for each type. Add
counters for each filter type. Rename the already existing fd_tcp_rule
to fd_tcp4_filter_cnt to match the style of other names. To avoid style
warnings, avoid assigning multiple parameters at once, and fix up one
other case where we did so previously.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When flushing and replaying FDIR filters, it is possible we would
disable ATR, and then re-enable it even though we should have kept
it disabled due to existing TCP/IPv4 filters. Fix this by checking
whether we have TCP4/IPv4 filters before re-enabling.
Alternatively, we could instead restore ATR and then replay filters,
however, this would cause us to rapidly enable and then disable ATR in
some cases.
Change-ID: I076e4cc1e4409bce7f98f3c213295433a4ff43d8
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Avinash Dayanand <avinash.dayanand@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we're about to reprogram the filters, we need to ensure that the
fd_tcp_rule count is correctly reset to 0. Otherwise, we will keep
a stale count that does not accurately reflect the number of programmed
TCPv4 filters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_fdir_filter_restore re-adds all existing filters, which already
checks when adding a TCPv4 filter to disable ATR. We don't need to make
the check twice, so remove this redundant code.
Change-ID: Ia0b0690e23523915199d601494557def135c9d7f
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move ATR exit check after we have sent the TCP/IPv4 filter to the ring
successfully. This avoids an issue where we potentially update the
filter count without actually succeeding in adding the filter. Now, we
only increment the fd_tcp_rule after we've succeeded. Additionally, we
will re-enable ATR mode only after deletion of the filter is actually
posted to the FDIR ring.
Change-ID: If5c1dea422081cc5e2de65618b01b4c3bf6bd586
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of setting err=true and checking this to determine when to free
the raw_packet near the end of the function, simply kfree and return
immediately. The resulting code is a bit cleaner and has one less
variable. This also resolves a subtle bug in the ipv4 case which could
fail to add the first filter and then never free the memory, resulting
in a small memory leak.
Change-ID: I7583aac033481dc794b4acaa14445059c8930ff1
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Avinash Dayanand <avinash.dayanand@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor the exit flow of the i40e_add_fdir_ethtool function. Move the
input_label to the end of the function, removing the dependency on
having a non-zero return value. Add a comment explaining why it is ok
not to free the fdir data structure, because the structure is now stored
in the fdir_filter_list.
Change-Id: I723342181d59cd0c9f3b31140c37961ba37bb242
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code originally included src_ip and dst_ip with enough space to
support ipv6 filters. However, no actual support for ipv6 filters has
been implemented. Thus, remove the arrays and just use __be32 values.
Should ipv6 support be added in the future, we can replace these with
a union that has sizes for both values.
Change-Id: I1bc04032244a80eb6ebc8a4e6c723a4a665c1dd5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware expects the port numbers for offloaded UDP tunnels in
Little Endian format. We accidentally sent the value in Big Endian
format which obviously will cause the wrong port number to be put into
the UDP tunnels list. This results in VxLAN and Geneve tunnel Rx
offloads being essentially disabled, unless the port number happens to
be identical after byte swapping. Note that i40e_aq_add_udp_tunnel()
will byteswap the parameter from host order into Little Endian so we
don't need worry about passing strictly a __le16 value to the command.
This patch essentially reverts b3f5c7bc88 ("i40e: Fix for extra byte
swap in tunnel setup", 2016-08-24), but in a way that makes the result
much more clear to the reader.
Fixes: b3f5c7bc88 ("i40e: Fix for extra byte swap in tunnel setup", 2016-08-24)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.
This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.
Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous commit introduced a field that tracks the features
that are disabled due to HW resource limitations as opposed
to the featured disabled by the user. This patch changes the
name of the field to make it more readable since it might get
confusing when looking at code containing both the flags
field and the auto_disable_features field together.
Change-ID: Idcc9888659698f6fe3ccff17c8c3f09b5026f708
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Our original filter limit of 8 was based on behavior that we saw from
Linux VMs. Now we're running Other Operating Systems under KVM and we
see that they commonly use more MAC filters. Since it seems weird to
require people to enable trusted VFs just to boot their OS, bump the
number of filters allowed by default.
Change-ID: I76b2dcb2ad6017e39231ad3096c3fb6f065eef5e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for DMA_ATTR_SKIP_CPU_SYNC and
DMA_ATTR_WEAK_ORDERING. By enabling both of these for the Rx path we
are able to see performance improvements on architectures that implement
either one due to the fact that page mapping and unmapping only has to
sync what is actually being used instead of the entire buffer. In addition
by enabling the weak ordering attribute enables a performance improvement
for architectures that can associate a memory ordering with a DMA buffer
such as Sparc.
Change-ID: If176824e8231c5b24b8a5d55b339a6026738fc75
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch clarifies the reason for removal of automatically
firmware-generated filter and explicit addition of filter which
accepts frames with any VLAN id.
Change-ID: Iabf180b6d61c4d8a36d3bcf8457c377a6f2aca0e
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issue that RSS offloading only works on PF0 by
using the direct register writing of the hash keys for the VFs instead
of using the admin queue command to do so.
Change-ID: Ia02cda7dbaa23def342e8786097a2c03db6f580b
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ethtool -e will error out with a X722 interface
as its EEPROM has a scope limit at offset 0x5B9FFF.
This patch fixes the issue by setting the EEPROM length to
the scope limit to avoid NVM read failure beyond that.
Change-ID: I0b7d4dd6c7f2a57cace438af5dffa0f44c229372
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a solution to avoid adding too many queues to num_lan_msix.
A recent refactor of queue pairs accidentally added all remaining
vectors to the num_lan_msix which can have adverse performance issues,
due to enabling more queues than the number of CPU cores.
This patch removes the old calculation, and replaces it with a simple
algorithm.
1) add queue pairs up to num_online_cpus(), but capped at half of total
vectors
2) then add alternative features such as flow directory and similar
3) finally, add the remaining vectors back to queue pairs, but capped
such that the total number of queue pairs does not exceed
num_online_cpus().
Change-ID: I668abf67d5011a1248866daba8885f4ff00cb8d9
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
(KISS is Keep It Simple, Stupid. Or is it?)
The client interface vastly overengineered for what it needs to do.
It was originally designed to support multiple clients on multiple
netdevs, possibly even with multiple drivers. None of this happened,
and now we know that there will only ever be one client for i40e
(i40iw) and one for i40evf (i40iwvf). So, time for some KISS. Since
i40e and i40evf are a Dynasty, we'll simplify this one to match the
VF interface.
First, be a Destroyer and remove all of the lists and locks required
to support multiple clients. Keep one static around to keep track of
one client, and track the client instances for each netdev in the
driver's pf (or adapter) struct. Now it's Almost Human.
Since we already know the client type is iWarp, get rid of any checks
for this. Same for VSI type - it's always going to be the same type,
so it's just a Parasite.
While we're at it, fix up some comments. This makes the function
headers actually match the functions.
These changes reduce code complexity, simplify maintenance,
squash some lurking timing bugs, and allow us to Rock and Roll All
Nite.
Change-ID: I1ea79948ad73b8685272451440a34507f9a9012e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some opcodes added & reordered to be in numerical order with the
rest of the opcodes.
This patch adds admin queue structs to support Wake on LAN feature
for X722.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acquire NVM lock before reads on all devices. Previously, locks were
only used for X722 and later. Fixes an issue where simultaneous X710
NVM accesses were interfering with each other.
Change-ID: If570bb7acf958cef58725ec2a2011cead6f80638
Signed-off-by: Aaron Salter <aaron.k.salter@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix typos and add the following to the scripts/spelling.txt:
varible||variable
While we are here, tidy up the comment blocks that fit in a single line
for drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c and
net/sctp/transport.c.
Link: http://lkml.kernel.org/r/1481573103-11329-11-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following message is logged from time to time when using i40e:
NOHZ: local_softirq_pending 08
i40e may schedule napi from a workqueue. Afterwards, softirqs are not run
in a deterministic time frame. The problem is the same as what was
described in commit ec13ee8014 ("virtio_net: invoke softirqs after
__napi_schedule") and this patch applies the same fix to i40e.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix, or rather, avoid a sparse warning caused by the fact that
csum_replace_by_diff expects to receive a __wsum value. Since the
calculation appears to work, simply typecast the passed paylen value to
__wsum to avoid the warning.
This seems pretty fishy since __wsum was obviously annotated as
a separate type on purpose, so this throws the entire calculation into
question. Since it currently appears to behave as expected, the typecast
is probably safe.
Change-ID: I4fdc5cddd589abc16098176e8a61127e761488f4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists an intermittent bug which causes the 'Link Detected'
field reported by the 'ethtool <iface>' command to be 'Yes' when
in fact, there is no link. This patch fixes the problem by
enabling temporary link polling when i40e_get_link_status returns
an error. This causes the driver to remember that an admin queue
command failed and polls, until the function returns with a success.
Change-Id: I64c69b008db4017b8729f3fc27b8f65c8fe2eaa0
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This ensures that the pvid which is stored in __le16 format is converted
to the CPU format. This will fix comparison issues on Big Endian
platforms.
Change-ID: I92c80d1315dc2a0f9f095d5a0c48d461beb052ed
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On Big Endian platforms we would incorrectly calculate the wrong switch
id since we did not properly convert the le16 value into CPU format.
Caught by sparse.
Change-ID: I69a2f9fa064a0a91691f7d0e6fcc206adceb8e36
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors the '%*ph' printk format specifier to instead use
the print_hex_dump function, as recommended by the '%*ph' documentation.
This produces better/more standardized output.
Change-ID: Id56700b4e8abc40ff8c04bc8379e7df04cb4d6fd
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a bug introduced with the addition of the per queue
ITR feature support in ethtool. With that addition, there were
functions added which converted the ITR settings to binary values.
The IS_ENABLED macros that run on those values check whether a bit
is set or not and with the value being binary, the bit check always
returned ITR disabled which prevents any updating of the ITR rate.
This patch fixes the problem by changing the functions to return the
current ITR value instead and renaming it to better reflect
its function. These functions now provide a value which will be
accurately asessed and update the ITR as intended.
Change-ID: I14f1d088d052e27f652aaa3113e186415ddea1fc
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This call is made just prior to running i40e_link_event. In
i40e_link_event, we set hw->phy.get_link_info to true just prior to
calling i40e_get_link_status, which conveniently runs
i40e_update_link_info for us. Thus, we are running i40e_update_link_info
twice, which seems like something we don't need to do...
Change-ID: I36467a570f44b7546d218c99e134ff97c2709315
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a call to the mac_address_write admin q function during
power down to update the PRTPM_SAH/SAL registers with the MC_MAG_EN bit
thus enabling multicast magic packet wakeup.
A FW workaround is needed to write the multicast magic wake up enable
bit in the PRTPM_SAH register. The FW expects the mac address write
admin q cmd to be called first with one of the WRITE_TYPE_LAA flags
and then with the multicast relevant flags.
*Note: This solution only works for X722 devices currently. A PFR will
clear the previously mentioned bit by default, but X722 has support for a
WOL_PRESERVE_ON_PFR flag which prevents the bit from being cleared. Once
other devices support this flag, this solution should work as well.
Change-ID: I51bd5b8535bd9051c2676e27c999c1657f786827
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in which the driver is unable to exit overflow
promiscuous mode after having added "too many" mac filters. It is
expected that after triggering overflow promiscuous, removing the
failed/extra filters should then disable overflow promiscuous mode.
The bug exists because we were intentionally skipping the sync_vsi_filter
path in cases where we were removing failed filters since they shouldn't
have been added to the firmware in the first place, however we still
need to go through the sync_vsi_filter code path to determine whether or
not it is ok to exit overflow promiscuous mode. This patch fixes the
bug by making sure we go through the sync_vsi_filter path in cases of
failed filters.
Change-ID: I634d249ca3e5fa50729553137c295e73e7722143
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethtool support needs to save more PHY information. The
added information includes FEC capabilities and 25G link
types. Without this change it is possible to lose 25G or
FEC settings by using ethtool.
Change-ID: Ie42255b1e901ffbf9583b8c46466a54894114280
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor how we add new filters to firmware to avoid a race condition
that can occur due to removing filters from the hash temporarily.
To understand the race condition, suppose that you have a number of MAC
filters, but have not yet added any VLANs. Now, add two VLANs in rapid
succession. A possible resulting flow would look something like the
following:
(1) lock hash for add VLAN
(2) add the new MAC/VLAN combos for each current MAC filter
(3) unlock hash
(4) lock hash for filter sync
(5) notice that we have a VLAN, so prepare to update all MAC filters
with VLAN=-1 to be VLAN=0.
(6) move NEW and REMOVE filters to temporary list
(7) unlock hash
(8) lock hash for add VLAN
(9) add new MAC/VLAN combos. Notice that no MAC filters are currently in
the hash list, so we don't add any VLANs <--- BUG!
(10) unlock hash
(11) sync the temporary lists to firmware
(12) lock hash for post-sync
(13) move the temporary elements back to the main list
....
Because we take filters out of the main hash into temporary lists, we
introduce a narrow window where it is possible that other callers to the
list will not see some of the filters which were previously added but
have not yet been finalized. This results in sometimes dropping VLAN
additions, and could also result in failing to add a MAC address on the
newly added VLAN.
One obvious way to avoid this race condition would be to lock the entire
firmware process. Unfortunately this does not work because adminq
firmware commands take a mutex which results in a sleep while atomic
BUG(). So, we can't use the simplest approach.
An alternative approach is to simply not remove the filters from the
hash list while adding. Instead, add an i40e_new_mac_filter structure
which we will use to track added filters. This avoids the need to remove
the filter from the hash list. We'll store a pointer to the original
i40e_mac_filter, along with our own copy of the state.
We won't update the state directly, so as to avoid race with other code
that may modify the state while under the lock. We are safe to read
f->macaddr and f->vlan since these only change in two locations. The
first is on filter creation, which must have already occurred. The
second is inside i40e_correct_vlan_filters which was previously run
after creation of this object and can't be run again until after. Thus,
we should be safe to read the MAC address and VLAN while outside the
lock.
We also aren't going to run into a use-after-free issue because the only
place where we free filters is when they are marked FAILED or when we
remove them inside the sync subtask. Since the subtask has its own
critical flag to prevent duplicate runs, we know this won't happen. We
also know that the only location to transition a filter from NEW to
FAILED is inside the subtask also, so we aren't worried about that
either.
Use the wrapper i40e_new_mac_filter for additions, and once we've
finalized the addition to firmware, we will update the filter state
inside a lock, and then free the wrapper structure.
In order to avoid a possible race condition with filter deletion, we
won't update the original filter state unless it is still
I40E_FILTER_NEW when we finish the firmware sync.
This approach is more complex, but avoids race conditions related to
filters being temporarily removed from the list. We do not need the same
behavior for deletion because we always unconditionally removed the
filters from the list regardless of the firmware status.
Change-Id: I14b74bc2301f8e69433fbe77ebca532db20c5317
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug where we modified the mac_filter_hash while outside a lock,
when handling addition of broadcast filters.
Normally, we add filters to firmware by batching the additions into
lists and issuing 1 update for every few filters. Broadcast filters are
handled differently, by instead setting the broadcast promiscuous mode
flags. In order to make sure the 1<->1 mapping of filters in our
addition array lined up with filters in the hlist tmp_add_list, we had
to remove the filter and move it back to the main hash. However, we
didn't do this under lock, which could cause consistency problems for
the list.
Fix this by updating i40e_update_filter_state logic so that it knows to
avoid broadcast filters. This ensures that we don't have to remove the
filter separately, and can put it back using the normal flow.
Change-ID: Id288fade80b3e3a9a54b68cc249188cb95147518
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The intent of this message was to indicate to a user that we might have
missed a timestamp event for a valid packet. The original method of
detecting the missed events relied on waiting until all 4 registers were
filled.
A recent commit d55458c0cd7a5 ("i40e: replace PTP Rx timestamp hang
logic") replaced this logic with much better detection
scheme that could detect a stalled Rx timestamp register even when other
registers were still functional.
The new logic means that a message will be displayed almost as soon as
a timestamp for a dropped frame occurs. This new logic highlights that
the hardware will attempt timestamp for frames which it later decides to
drop. The most prominent example is when a multicast PTP frame is
received on a multicast address that we are not subscribed to.
Because the hardware initiates the Rx timestamp as soon as possible, it
will latch an RXTIME register, but then drop the packet.
This results in users being confused by the message as they are not
expecting to see dropped timestamp messages unless their application
also indicates that timestamps were missing.
Resolve this by reducing the severity and frequency of the displayed
message. We now only print the message if 3 or 4 of the RXTIME registers
are stalled and get cleared within the same watchdog event. This ensures
that the common case does not constantly display the message.
Additionally, since the message is likely not as meaningful to most
users, reduce the message to a dev_dbg instead of a dev_warn.
Users can still get a count of the number of timestamps dropped by
reading the ethtool statistics value, if necessary.
Change-ID: I35494442226a444c418dfb4f91a3070d06c8435c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store the FEC status bits from the link up event into the
hw_link_info structure.
Change-ID: I9a7b256f6dfb0dce89c2f503075d0d383526832e
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently i40e_bus_info has PCI device and function info only and log
messages print device number as bus number. Added field to provide bus
number info and modified log statements to print bus, device and
function information.
Change-ID: I811617cee2714cc0d6bade8d369f57040990756f
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function i40e_client_prepare() can never return an error. So make it
void and quit checking its return value.
Change-ID: I9ff311e2324dde329eb68648efb2c94aaff856db
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original comment implies that the only location where the raw_packet
buffer will be freed is in i40e_clean_tx_ring() which is incorrect. In
fact this isn't even the normal case. Update the comment explaining
where the memory is freed.
Change-ID: Ie0defc35ed1c3af183f81fdc60b6d783707a5595
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reorganize the i40e_pull_tail() logic, doing it in i40e_add_rx_frag()
where it's cheaper. The igb driver does this the same way.
Also renames i40e_page_is_reserved() to reflect what it actually
tests.
Change-ID: Icd9cc507aae1fcdc02308b3a09034111b4c24071
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch reduces the size of struct i40e_rx_buffer by one pointer,
and makes the i40e driver a little more consistent with the igb driver
in terms of packets that span buffers.
We do this by moving the skb field from struct i40e_rx_buffer to
struct i40e_ring. We pass the skb we already have (or NULL if we
don't) to i40e_fetch_rx_buffer(), which skips the skb allocation if we
already have one for this packet.
Change-ID: I4ad48a531844494ba0c5d8e1a62209a057f661b0
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On packet RX, we perform a DMA sync for CPU before passing the
packet up. Here we limit that sync to the actual length of the
incoming packet, rather than always syncing the entire buffer.
Change-ID: I626aaf6c37275a8ce9e81efcaa773f327b331487
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can avoid the minor bit of work by calling check params after we
check for the client instance, since we're about to return early in
cases where we do not have a client.
Change-ID: I56f8ea2ba48d4f571fa331c9ace50819a022fa1c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to the resolution of the register controlling interrupt rate
limiting, setting certain values for the interrupt rate limit make it
appear as though the limiting is not completely accurate. The problem
is that the interrupt rate limit is getting rounded down to the nearest
multiple of 4. This patch fixes the problem by adding some feedback to
the user as to the actual interrupt rate limit being used when it
differs from the requested limit. Without this patch setting interrupt
rate limits may appear to behave inaccurately.
Change-ID: I3093cf3f2d437d35a4c4f4bb5af5ce1b85ab21b7
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors the macro INTRL_USEC_TO_REG into a static inline
function and fixes a couple subtle bugs caused by the macro.
This patch fixes a bug which was caused by passing a bad register value
to the firmware. If enabling interrupt rate limiting, a non-zero value
for the rate limit must be used. Otherwise the firmware sets the
interrupt rate limit to the maximum value. Due to the limited
resolution of the register, attempting to set a value of 1, 2, or 3
would be rounded down to 0 and limiting was left enabled, causing
unexpected behavior.
This patch also fixes a possible bug in which using the macro itself can
introduce unintended side-affects because the macro argument is used
more than once in the macro definition (e.g. a variable post-increment
argument would perform a double increment on the variable).
Without this patch, attempting to set interrupt rate limits of 1, 2, or
3 results in unexpected behavior and future use of this macro could
cause subtle bugs.
Change-Id: I83ac842de0ca9c86761923d6e3a4d7b1b95f2b3f
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After refactoring the client open and close code, this is no longer
needed. Remove it.
Change-ID: If8e6e32baa354d857c2fd8b2f19404f1786011c4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does some quick work to pull some of the data off of the stack
and hopefully start storing it in the Tx buffer info section of the Tx
ring. Ideally we should be moving away from having to store much of
anything on the stack and can just maintain it all in the descriptor rings.
Change-ID: I4b4715ea1920e122502482b3f9e56a9a6cb1e9fe
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
'struct i40e_dma_mem' defined with 'packed' directive causing kernel
unaligned errors on sparc.
e.g.
i40e: Intel(R) Ethernet Connection XL710 Network Driver - version
1.6.16-k
i40e: Copyright (c) 2013 - 2014 Intel Corporation.
Kernel unaligned access at TPC[44894c] dma_4v_alloc_coherent+0x1ac/0x300
Kernel unaligned access at TPC[44894c] dma_4v_alloc_coherent+0x1ac/0x300
Kernel unaligned access at TPC[44894c] dma_4v_alloc_coherent+0x1ac/0x300
Kernel unaligned access at TPC[44894c] dma_4v_alloc_coherent+0x1ac/0x300
Kernel unaligned access at TPC[44894c] dma_4v_alloc_coherent+0x1ac/0x300
i40e 0000:03:00.0: fw 5.1.40981 api 1.5 nvm 5.04 0x80002548 0.0.0
This can be fixed with get_unaligned/put_unaligned(). However no
reference in driver shows that 'struct i40e_dma_mem' directly shoved
into NIC hardware. But instead fields of the struct are being read and
used for hardware. Therefore, __packed is unnecessary for 'struct
i40e_dma_mem'.
In addition, although 'struct i40e_virt_mem' doesn't cause any
unaligned access, keeping it packed is unnecessary as well because
of aforementioned reason.
This change make 'struct i40e_dma_mem' and 'struct i40e_virt_mem'
unpacked.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I40E_MAC_X710 was supposed to be for 10G and I40E_MAC_XL710
was supposed to be for 40G. But function i40e_is_mac_710
sets I40E_MAC_XL710 for all device IDS, I40E_MAC_X710 is not
used at all. As there is nothing to compare there is no need
for this function. Thus deprecating this extra macro and
removing this function entirely and replacing it with a direct
check.
Change-ID: I7d1769954dccd574a290ac04adb836ebd156730e
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using i40e_add_filter or i40e_del_filter directly, when
adding a MAC address, we should normally be using i40e_add_mac_filter or
i40e_del_mac_filter. These functions correctly handle the various cases
of VLAN mode or PVID settings. This ensures consistency and avoids the
issues that can occur with the recent addition of a WARN_ON() in
i40e_sync_vsi_filters.
Change-ID: I7fe62db063391fdd1180b2d6a6a3c5ab4307eeee
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use __i40e_del_filter instead of using i40e_del_filter() which will
avoid doing an additional search to delete a filter we already have the
pointer for.
Change-ID: Iea5a7e3cafbf8c682ed9d3b6c69cf5ff53f44daf
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These functions purpose is to add a new MAC filter correctly, whether
we're using VLANs or not. Their goal is to ensure that all active VLANs
get the new MAC filter. Rename them so that their intent is clear. They
function correctly regardless of whether we have any active VLANs or
only have I40E_VLAN_ANY filters. The new names convey how they function
in a more clear manner.
Change-ID: Iec1961f968c0223a7132724a74e26a665750b107
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function won't be appreciably slower when in VLAN mode, so there is
no real reason to not just call it directly. In either case, we still
must search the full table for a MAC/VLAN pair. We do get to stop
searching a tiny bit early in the case of knowing we are not in VLAN
mode, but this is a minor savings and we can avoid the code complexity
by not having to worry about the check.
Change-ID: I533412195b3a42f51cf629e3675dd5145aea8625
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fold the check for determining when to call i40e_put_mac_in_vlan directly
into the function so that we don't need to decide which function to use
ahead of time. This allows us to just call i40e_put_mac_in_vlan directly
without having to check ahead of time.
Change-ID: Ifff526940748ac14b8418be5df5a149502eed137
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we have the separate i40e_(add|rm)_vlan_all_mac functions, we
should not be using the i40e_vsi_kill_vlan or i40e_vsi_add_vlan
functions when PVID is set or when VID is less than 1. This allows us to
remove some checks in i40e_vsi_add_vlan and ensures that callers which
need to handle VID=0 or VID=-1 don't accidentally invoke the VLAN mode
handling used to convert filters when entering VLAN mode. We also update
the functions to take u16 instead of s16 as well since they no longer
expect to be called with VID=I40E_VLAN_ANY.
Change-ID: Ibddf44a8bb840dde8ceef2a4fdb92fd953b05a57
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .match_method field is a u8, so we shouldn't be casting to a u16,
and because it is only one byte, we do not need to byte swap anything.
Just assign the value directly. This avoids issues on Big Endian
architectures which would have byte swapped and then incorrectly
truncated the value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bimmy Pujari <bimmy.pujari@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to how we handled exiting VLAN mode, move the logic
in i40e_vsi_add_vlan into i40e_sync_vsi_filters. Extract this logic into
its own function for ease of understanding as it will become quite
complex.
The new function, i40e_correct_mac_vlan_filters() correctly updates all
filters for when we need to enter VLAN mode, exit VLAN mode, and also
enforces the PVID when assigned.
Call i40e_correct_mac_vlan_filters from i40e_sync_vsi_filters passing it
the number of active VLAN filters, and the two temporary lists.
Remove the function for updating VLAN=0 filters from i40e_vsi_add_vlan.
The end result is that the logic for entering and exiting VLAN mode is
in one location which has the most knowledge about all filters. This
ensures that we always correctly have the non-VLAN filters assigned to
VID=0 or VID=-1 regardless of how we ended up getting to this result.
Additionally this enforces the PVID at sync time so that we know for
certain that an assigned PVID results in only filters with that PVID
will be added to the firmware.
Change-ID: I895cee81e9c92d0a16baee38bd0ca51bbb14e372
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current flow for adding or updating the PVID for a VF uses
i40e_vsi_add_vlan and i40e_vsi_kill_vlan which each take, then release
the hash lock. In addition the two functions also must take special care
that they do not perform VLAN mode changes as this will make the code in
i40e_ndo_set_vf_port_vlan behave incorrectly.
Fix these issues by using the new helper functions i40e_add_vlan_all_mac
and i40e_rm_vlan_all_mac which expect the hash lock to already be taken.
Additionally these functions do not perform any state updates in regards
to VLAN mode, so they are safe to use in the PVID update flow.
It should be noted that we don't need the VLAN mode update code here,
because there are only a few flows here.
(a) we're adding a new PVID
In this case, if we already had VLAN filters the VSI is knocked
offline so we don't need to worry about pre-existing VLAN filters
(b) we're replacing an existing PVID
In this case, we can't have any VLAN filters except those with the old
PVID which we already take care of manually.
(c) we're removing an existing PVID
Similarly to above, we can't have any existing VLAN filters except
those with the old PVID which we already take care of correctly.
Because of this, we do not need (or even want) the special accounting
done in i40e_vsi_add_vlan, so use of the helpers is a saner alternative.
It also opens the door for a future patch which will refactor the flow
of i40e_vsi_add_vlan now that it is not needed in this function.
Change-ID: Ia841f63da94e12b106f41cf7d28ce8ce92f2ad99
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future refactor of how the PF assigns a PVID to a VF will want to be
able to add and remove a block of filters by VLAN without worrying about
accidentally triggering the accounting for I40E_VLAN_ANY. Additionally
the PVID assignment would like to be able to batch several changes under
one use of the mac_filter_hash_lock.
Factor out the addition and deletion of a VLAN on all MACs into their
own function which i40e_vsi_(add|kill)_vlan can use. These new functions
expect the caller to take the hash lock, as well as perform any
necessary accounting for updating I40E_VLAN_ANY filters if we are now
operating under VLAN mode.
Change-ID: If79e5b60b770433275350a74b3f1880333a185d5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a subtle issue with the code for converting VID=-1 filters into VID=0
filters when adding a new VLAN. Previously the code deleted the VID=-1
filter, and then added a new VID=0 filter. In the rare case that the
addition fails due to -ENOMEM, we end up completely deleting the filter
which prevents recovery if memory pressure subsides. While it is not
strictly an issue because it is likely that memory issues would result
in many other problems, we shouldn't delete the filter until after the
addition succeeds.
Change-ID: Icba07ddd04ecc6a3b27c2e29f2c1c8673d266826
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current caller of i40e_update_filter_state incorrectly passes
aq_ret, an i40e_status variable, instead of the expected aq_err. This
happens to work because i40e_status is actually just a typedef integer,
and 0 is still the successful return. However i40e_update_filter_state
has special handling for ENOSPC which is currently being ignored.
Also notice that firmware does not update the per-filter response for
many types of errors, such as EINVAL. Thus, modify the filter setup so
that the firmware response memory is pre-set with I40E_AQC_MM_ERR_NO_RES.
This enables us to refactor i40e_update_filter_state, removing the need
to pass aq_err and avoiding a need for having 3 different flows for
checking the filter state.
The resulting code for i40e_update_filter_state is much simpler, only
a single loop and we always check each filter response value every time.
Since we pre-set the response value to match our expected error this
correctly works for all success and error flows.
Change-ID: Ie292c9511f34ee18c6ef40f955ad13e28b7aea7d
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previous code refactors have accidentally caused issues with the
counting of active_filters. Avoid similar issues in the future by simply
re-counting the active filters every time after we handle add and delete
of all the filters. Additionally this allows us to simplify the check
for when we exit promiscuous mode since we can combine the check for
failed filters at the same time.
Additionally since we recount filters at the end we need to set
vsi->promisc_threshold as well.
The resulting code takes a bit longer since we do have to loop over
filters again. However, the result is more readable and less likely to
become incorrect due to failed accounting of filters in the future.
Finally, this ensures that it is not possible for vsi->active_filters to
ever underflow since we never decrement it.
Change-ID: Ib4f3a377e60eb1fa6c91ea86cc02238c08edd102
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A product decision has been made to defeature detection of PTP frames
over L4 (UDP) on the XL710 MAC. Do not advertise support for L4
timestamping.
Change-ID: I41fbb0f84ebb27c43e23098c08156f2625c6ee06
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The service task lock was being set in the scheduling function, not the
actual service task. This would potentially leave the bit set for a long
time before the task actually ran. Furthermore, if the service task
takes too long, it calls the schedule function to reschedule itself -
which would fail to take the lock and do nothing.
Instead, set and clear the lock bit in the service task itself. In the
process, get rid of the i40e_service_event_complete() function, which is
really just two lines of code that can be put right in the service task
itself.
Change-ID: I83155e682b686121e2897f4429eb7d3f7c669168
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Depending on external PHY type, register access method should be
different. Clause22 or Clause45 can be chosen for different PHYs.
Implemented functions apply correct access method for used device.
Change-ID: If39d5f0da9c0b905a8cbdc1ab89885535e7d0426
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds adminq support for Forward Error
Correction ("FEC")for 25g products.
Change-ID: Iaff4910737c239d2c730e5c22a313ce9c37d3964
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jacek Naczyk <jacek.naczyk@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for 25G devices - defines and data structures.
One tricky part here is that the firmware support for these
Devices introduces a mismatch between the PHY type enum and
the bitfields for the phy types.
This change creates a macro and uses it to increment the 25G
PHY values when creating 25G bitfields.
Change-ID: I69b24d837d44cf9220bf5cb8dd46c5be89ce490b
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace the %d specifier used for printing vsi->active_filters and
vsi->promisc_threshold with an unsigned %u format specifier. While it is
unlikely in practice that these values will ever reach such a large
number they are unsigned values and thus should not be interpreted as
negative numbers.
Change-ID: Iff050fad5a1c8537c4c57fcd527441cd95cfc0d4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Before this patch "ethtool -p" was not blinking the LEDs on boards
with 1G BaseT PHYs.
This commit identifies 1G BaseT boards as having the LEDs connected
to the MAC. Also, renamed the flag to be more descriptive of usage.
The flag is now I40E_FLAG_PHY_CONTROLS_LEDS.
Change-ID: I4eb741da9780da7849ddf2dc4c0cb27ffa42a801
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The netdev->dev_addr MAC filter already exists in the
MAC/VLAN hash table, as it is added when we configure
the netdev in i40e_configure_netdev. Because we already
know that this address will be updated in the
hash_for_each loops, we do not need to handle it
specially. This removes duplicate code and simplifies
the i40e_vsi_add_vlan and i40e_vsi_kill_vlan functions.
Because we know these filters must be part of the
MAC/VLAN hash table, this should not have any functional
impact on what filters are included and is merely a code
simplification.
Change-ID: I5e648302dbdd7cc29efc6d203b7019c11f0b5705
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the function i40e_napi-poll() returns 0 when it clean completely
the Rx rings, but this foul budget accounting in core code.
Fix this by returning the actual work done, capped to budget - 1, since
the core doesn't allow to return the full budget when the driver modifies
the NAPI status
This is based on a similar change that was made for the ixgbe driver by
Paolo Abeni.
Change-ID: Ic3d93ad2fa2fc8ce3164bc461e69367da0f9173b
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous commit 53cb6e9e89 ("i40e: Removal of workaround for simple
MAC address filter deletion") removed a workaround for some
firmware versions which was reported to not be necessary in production
NICs. Unfortunately this workaround is necessary in some configurations,
specifically the Ethernet Controller XL710 for 40GbE QSFP+ (8086:1583).
Without this patch, the mentioned NICs with current firmware exhibit
issues when adding VLANs, as outlined by the following reproduction:
$modprobe i40e
$ip link set <device> up
$ip link add link <device> vlan100 type vlan id 100
$dmesg | tail
<snip>
kernel: i40e 0000:82:00.0: Error I40E_AQ_RC_EINVAL adding RX
filters on PF, promiscuous mode forced on
This results in filters being marked as FAILED and setting the device in
promiscuous mode.
The root cause of receiving the -EINVAL error response appears to be due
to a conflict with the default MAC filter which still exists on the
default firmware for this device. Attempting to add a new VLAN filter on
the default MAC address conflicts with the IGNORE_VLAN setting on the
default rule.
Change-ID: I4d8f6d48ac5f60cfe981b3baad30eb4d7c170d61
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_txd_use_count function was fast but confusing. In the comments,
it even admits that it's ugly. So replace it with a new function that is
(very) slightly faster and has extensive commenting to help the thicker
among us (including the author, who will forget in a week) understand
how it works.
Change-ID: Ifb533f13786a0bf39cb29f77969a5be2c83d9a87
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes the driver log link speed change. Before applying the
patch link messages were printed only on state change. Now message is
printed when link is brought up or down and when speed changes.
Change-ID: Ifbee14b4b16c24967450b3cecac6e8351dcc8f74
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck