1. Determine autoneg on|off setting from link_info->autoneg. Using the
firmware returned setting can be misleading if autoneg is changed and
there hasn't been a phy update from the firmware.
2. If autoneg is disabled, link_info->autoneg should be set to 0 to
indicate both speed and flow control autoneg are disabled.
3. To enable autoneg flow control, speed autoneg must be enabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change to the mdb code confused the compiler to the point
where it did not realize that the port-group returned from
br_mdb_add_group() is always valid when the function returns a nonzero
return value, so we get a spurious warning:
net/bridge/br_mdb.c: In function 'br_mdb_add':
net/bridge/br_mdb.c:542:4: error: 'pg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
__br_mdb_notify(dev, entry, RTM_NEWMDB, pg);
Slightly rearranging the code in br_mdb_add_group() makes the problem
go away, as gcc is clever enough to see that both functions check
for 'ret != 0'.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9e8430f8d6 ("bridge: mdb: Passing the port-group pointer to br_mdb module")
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Kochetkov says:
====================
Fixes for rockchip EMAC
Here is a set of 3 patches what fix koops, memory leak and
rockchip EMAC hang. Tested on radxarock lite.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
EMAC could be disabled, while there is some sb_buff
in use. That buffers got lost for linux.
In order to reproduce run on device during active ethernet work:
ifconfig eth0 down
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EMAC reset internal tx ring pointer to zero at statup.
txbd_curr and txbd_dirty can be different from zero.
That cause ethernet transfer hang (no packets transmitted).
In order to reproduce, run on device:
ifconfig eth0 down
ifconfig eth0 up
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the unaligned accesses seen on GRE TEB tunnels when
generating hash keys. Specifically what this patch does is make it so that
we force the use of skb_copy_bits when the GRE inner headers will be
unaligned due to NET_IP_ALIGNED being a non-zero value.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5 driver fixes for 4.5-rc2
We added here a patch from Matan and Alaa for addressing Linus comments on
the mess w.r.t reserved field names in the driver/firmware auto-generated file.
Once the patch hits linus tree, we'll ask Doug to rebase his tree on that
rc so both net-next and rdma-next development for 4.6 will be done under
the fixed robust form.
Also provided two patches that addresses the dynamic ndo initialization
issue of mlx5e netdevice.
Or and Saeed.
changes from V1: (Only first patch was changed)
In this V we fixed the issues addressed in Or's previous e-mail.
1. Offsets took into account two dimensional u8 arrays
2. Offsets took into account nesting unions and structs
3. Offsets for unions
4. Offsets for any reserved field
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently our netdevice ops is a one static global variable which
is referenced by all mlx5e netdevice instances. This can be
problematic when different driver instances do not share same
HW capabilities (e.g SRIOV PF and VFs probed to the host).
Now we have two constant global netdevice ops variables, one
for basic netdevice ops and the other with extended SRIOV ops,
on netdevice construction we choose the one suitable for
current device capabilities.
Fixes: 66e49dedad ("net/mlx5e: Add support for SR-IOV ndos")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mlx5e_select_queue is redundant since num_tc is always 1.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_ifc.h is a header file representing the API and ABI between
the driver to the firmware and hardware. This file is used from
both the mlx5_ib and mlx5_core drivers.
Previously, this file used incrementing counter to indicate
reserved fields, for example:
struct mlx5_ifc_odp_per_transport_service_cap_bits {
u8 send[0x1];
u8 receive[0x1];
u8 write[0x1];
u8 read[0x1];
u8 reserved_0[0x1];
u8 srq_receive[0x1];
u8 reserved_1[0x1a];
};
If one developer implements through net-next feature A that uses
reserved_0, they replace it with featureA and renames reserved_1 to
reserved_0. In the same kernel cycle, a 2nd developer could implement
feature B through the rdma tree, that uses reserved_1 and split it to
featureB and a smaller reserved_1 field. This will cause a conflict
when the two trees are merged.
The source of this conflict is that the 1st developer changed *all*
reserved fields.
As Linus suggested, we change the layout of structs to:
struct mlx5_ifc_odp_per_transport_service_cap_bits {
u8 send[0x1];
u8 receive[0x1];
u8 write[0x1];
u8 read[0x1];
u8 reserved_at_4[0x1];
u8 srq_receive[0x1];
u8 reserved_at_6[0x1a];
};
This makes the conflicts much more rare and preserves the locality of
changes.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This gets us functional GPU reset again, like we had until a refactor
at merge time. Tested with a little patch to stuff in a broken binner
job every 100 frames.
Signed-off-by: Eric Anholt <eric@anholt.net>
This may actually get us a feature that the closed driver didn't have:
turning off the GPU in between rendering jobs, while the V3D device is
still opened by the client.
There may be some tuning to be applied here to use autosuspend so that
we don't bounce the device's power so much, but in steady-state
GPU-bound rendering we keep the power on (since we keep multiple jobs
outstanding) and even if we power cycle on every job we can still
manage at least 680 fps.
More importantly, though, runtime PM will allow us to power off the
device to do a GPU reset.
v2: Switch #ifdef to CONFIG_PM not CONFIG_PM_SLEEP (caught by kbuild
test robot)
Signed-off-by: Eric Anholt <eric@anholt.net>
We were tracking the "where are the head pointers pointing" globally,
so if another job reused the same BOs and execution was at the same
point as last time we checked, we'd stop and trigger a reset even
though the GPU had made progress.
Signed-off-by: Eric Anholt <eric@anholt.net>
These ioctls end up getting exposed to fairly directly to GL users,
and having normal user operations print DRM errors is obviously wrong.
The message was originally to give us some idea of what happened when
a hang occurred, but we have a DRM_INFO from reset for that.
Signed-off-by: Eric Anholt <eric@anholt.net>
This caused the wait ioctls to claim that waiting had completed when
we actually got interrupted by a signal before it was done. Fixes
broken rendering throttling that produced serious lag in X window
dragging.
Signed-off-by: Eric Anholt <eric@anholt.net>
Apparently in hardware (as opposed to simulation), the clear colors
need to be uploaded before the render config, otherwise they won't
take effect. Fixes igt's vc4_wait_bo/used-bo-* subtests.
Signed-off-by: Eric Anholt <eric@anholt.net>
There is presently a race condition between the bonding periodic
link monitor and the updating of a slave's speed and duplex. The former
occurs on a periodic basis, and the latter in response to a driver's
calling of netif_carrier_on.
It is possible for the periodic monitor to run between the
driver call of netif_carrier_on and the receipt of the NETDEV_CHANGE
event that causes bonding to update the slave's speed and duplex. This
manifests most notably as a report that a slave is up and "0 Mbps full
duplex" after enslavement, but in principle could report an incorrect
speed and duplex after any link up event if the device comes up with a
different speed or duplex. This affects the 802.3ad aggregator
selection, as the speed and duplex are selection criteria.
This is fixed by updating the speed and duplex in the periodic
monitor, prior to using that information.
This was done historically in bonding, but the call to
bond_update_speed_duplex was removed in commit 876254ae27 ("bonding:
don't call update_speed_duplex() under spinlocks"), as it might sleep
under lock. Later, the locking was changed to only hold RTNL, and so
after commit 876254ae27 ("bonding: don't call update_speed_duplex()
under spinlocks") this call is again safe.
Tested-by: "Tantilov, Emil S" <emil.s.tantilov@intel.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: dingtianhong <dingtianhong@huawei.com>
Fixes: 876254ae27 ("bonding: don't call update_speed_duplex() under spinlocks")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The am79c961a.c driver fails to build with clang because of an
unusual inline assembly construct:
drivers/net/ethernet/amd/am79c961a.c:53:7: error: invalid % escape in inline assembly string
"str%?h %1, [%2] @ NET_RAP\n\t"
The same change has been done a decade ago in arch/arm as of
6a39dd6222 ("[ARM] 3759/2: Remove uses of %?"), but apparently
some drivers were missed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smc91x driver doesn't honor the probe deferral mechanism when the
interrupt source is not yet available, such as one provided by a gpio
controller not probed.
Fix this by propagating the platform_get_irq() error code as the probe
return value.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
Subject: [PATCH net v2 0/4] net: phy: bcm7xxx 40nm PHY fixes
Here is a collection of fixes for the 40nm Ethernet PHY supported
by the 7xxx PHY driver, please also queue these fixes for stable.
Changes in v2:
- dropped the cleanup patch, not appropriate
- added another patch removing bogus wildcard entries
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the two wildcard entries, they serve no purpose and will match way too
many devices, some of them being covered by the driver in
drivers/net/phy/broadcom.c. Remove the now unused bcm7xxx_dummy_config_init()
function which would produce a warning.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we were wrongly advertising gigabit features for these 10/100 only
Ethernet PHYs, bcm7xxx_config_init() which is supposed to apply workaround
would have not run since the check would be true, now that we have fixed the
PHY features, remove that check since it has no reasoning to be there anymore.
Fixes: e18556ee3b ("net: phy: bcm7xxx: do not use PHY_BRCM_100MBPS_WAR")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY entries for BCM7425/29/35 declare the 40nm Ethernet PHY as being
10/100/1000 capable, while this is just a 10/100 capable PHY device, fix that.
Fixes: d068b02cfd ("net: phy: add BCM7425 and BCM7429 PHYs")
Fixes: 9458ceab49 ("net: phy: bcm7xxx: Add entry for BCM7435")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clear and set masks in the call to phy_set_clr_bits() called from
bcm7xxx_config_init() are inverted. We need to fix this by swapping the two
arguments, that is, set 0 bits, but clear the shade mode 2 enable bit.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov says:
====================
ravb: fix the fallout of R-Car gen3 gPTP support
Here's a set of 2 patches against DaveM's 'net.git' repo fixing up the
incomplete commit f5d7837f96 ("ravb: ptp: Add CONFIG mode support").
I'm proposing these as fixes but they can be merged as cleanups as well...
[1/2] ravb: kill duplicate setting of CCC.CSEL
[2/2] ravb: skip gPTP start/stop on R-Car gen3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for the R-Car gen3 gPTP active in configuration mode,
some call sites of ravb_ptp_{init|stop}() were missed due to an oversight.
Add checks for the R-Car gen2 SoCs around these...
Fixes: f5d7837f96 ("ravb: ptp: Add CONFIG mode support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for the R-Car gen3 gPTP active in configuration mode,
the code setting the CCC.CSEL field was duplicated due to an oversight.
For R-Car gen 2 it's just redundant and for R-Car gen3 the write at this
time is probably ignored due to CCC.GAC bit being already set...
Fixes: f5d7837f96 ("ravb: ptp: Add CONFIG mode support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull cifs fixes from Steve French:
"A small set of cifs fixes.
I am still reviewing some more, recently submitted SMB3 fixes, but
these three are small and safe and ready now"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix erroneous return value
cifs: fix potential overflow in cifs_compose_mount_options
cifs: remove redundant check for null string pointer
- Fix for an unpleasant crash when the VM is created without a timer
- Allow HYP mode to access the full PA space, and not only 40bit
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJWw2HjAAoJEL/70l94x66DdAwH/iM6R6dlgNk60X0oquujAbra
p9t/6ulNDxMHz/ICQkk6VuH12XMQS9dYr22SLUGuDOVOyB3VB6SQk3H+t4yUUIuD
8HY3ZVFGoX56EsTel3S3/elIksG9SLPIyma8FImbMvPzjTV8KLqEEexZVmMpq8og
ufG5rPkwBbg2r4OMl8NBmaGB822IMT8WfL5ECsnml5BDnU4Eo680AcMm8FZgqRTS
cKiT04QkRhQAiemoVdIPJhAcslSTTj5o6cmD1XwcmRR4z3HdZFBAt+IigC9ZQvnE
Y7J9L7pBgzr8j91lFRPcv1pM0D5+EOP4C3mjNDg4ghvvjko0S8UNS1EhRL1upk0=
=DJUb
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull ARM KVM fixes from Paolo Bonzini:
- Fix for an unpleasant crash when the VM is created without a timer
- Allow HYP mode to access the full PA space, and not only 40bit
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
arm64: KVM: Configure TCR_EL2.PS at runtime
KVM: arm/arm64: Fix reference to uninitialised VGIC
If cgroup writeback is in use, an inode is associated with a cgroup
for writeback. If the inode's main dirtier changes to another cgroup,
the association gets updated asynchronously. Nothing was pinning the
superblock while such switches are in progress and superblock could go
away while async switching is pending or in progress leading to
crashes like the following.
kernel BUG at fs/jbd2/transaction.c:319!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
CPU: 1 PID: 29158 Comm: kworker/1:10 Not tainted 4.5.0-rc3 #51
Hardware name: Google Google, BIOS Google 01/01/2011
Workqueue: events inode_switch_wbs_work_fn
task: ffff880213dbbd40 ti: ffff880209264000 task.ti: ffff880209264000
RIP: 0010:[<ffffffff803e6922>] [<ffffffff803e6922>] start_this_handle+0x382/0x3e0
RSP: 0018:ffff880209267c30 EFLAGS: 00010202
...
Call Trace:
[<ffffffff803e6be4>] jbd2__journal_start+0xf4/0x190
[<ffffffff803cfc7e>] __ext4_journal_start_sb+0x4e/0x70
[<ffffffff803b31ec>] ext4_evict_inode+0x12c/0x3d0
[<ffffffff8035338b>] evict+0xbb/0x190
[<ffffffff80354190>] iput+0x130/0x190
[<ffffffff80360223>] inode_switch_wbs_work_fn+0x343/0x4c0
[<ffffffff80279819>] process_one_work+0x129/0x300
[<ffffffff80279b16>] worker_thread+0x126/0x480
[<ffffffff8027ed14>] kthread+0xc4/0xe0
[<ffffffff809771df>] ret_from_fork+0x3f/0x70
Fix it by bumping s_active while cgroup association switching is in
flight.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Tahsin Erdogan <tahsin@google.com>
Link: http://lkml.kernel.org/g/CAAeU0aNCq7LGODvVGRU-oU_o-6enii5ey0p1c26D1ZzYwkDc5A@mail.gmail.com
Fixes: d10c809552 ("writeback: implement foreign cgroup inode bdi_writeback switching")
Cc: stable@vger.kernel.org #v4.5+
Signed-off-by: Jens Axboe <axboe@fb.com>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contain a rather large batch for your net that
includes accumulated bugfixes, they are:
1) Run conntrack cleanup from workqueue process context to avoid hitting
soft lockup via watchdog for large tables. This is required by the
IPv6 masquerading extension. From Florian Westphal.
2) Use original skbuff from nfnetlink batch when calling netlink_ack()
on error since this needs to access the skb->sk pointer.
3) Incremental fix on top of recent Sasha Levin's lock fix for conntrack
resizing.
4) Fix several problems in nfnetlink batch message header sanitization
and error handling, from Phil Turnbull.
5) Select NF_DUP_IPV6 based on CONFIG_IPV6, from Arnd Bergmann.
6) Fix wrong signess in return values on nf_tables counter expression,
from Anton Protopopov.
Due to the NetDev 1.1 organization burden, I had no chance to pass up
this to you any sooner in this release cycle, sorry about that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The unix_dgram_sendmsg routine use the following test
if (unlikely(unix_peer(other) != sk && unix_recvq_full(other))) {
to determine if sk and other are in an n:1 association (either
established via connect or by using sendto to send messages to an
unrelated socket identified by address). This isn't correct as the
specified address could have been bound to the sending socket itself or
because this socket could have been connected to itself by the time of
the unix_peer_get but disconnected before the unix_state_lock(other). In
both cases, the if-block would be entered despite other == sk which
might either block the sender unintentionally or lead to trying to unlock
the same spin lock twice for a non-blocking send. Add a other != sk
check to guard against this.
Fixes: 7d267278a9 ("unix: avoid use-after-free in ep_remove_wait_queue")
Reported-By: Philipp Hahn <pmhahn@pmhahn.de>
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Tested-by: Philipp Hahn <pmhahn@pmhahn.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix for an unpleasant crash when the VM is created without a timer
- Allow HYP mode to access the full PA space, and not only 40bit
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1qeo
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/ARM fixes for 4.5-rc4
- Fix for an unpleasant crash when the VM is created without a timer
- Allow HYP mode to access the full PA space, and not only 40bit
The present unix_stream_read_generic contains various code sequences of
the form
err = -EDISASTER;
if (<test>)
goto out;
This has the unfortunate side effect of possibly causing the error code
to bleed through to the final
out:
return copied ? : err;
and then to be wrongly returned if no data was copied because the caller
didn't supply a data buffer, as demonstrated by the program available at
http://pad.lv/1540731
Change it such that err is only set if an error condition was detected.
Fixes: 3822b5c2fc ("af_unix: Revert 'lock_interruptible' in stream receive code")
Reported-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor register size and interrupt acknowledgement fixes which only showed
up in testing on newer hardware, but mostly a fix to the MM refcount
handling to prevent a recursive refcount issue when mmap() is used on
the file descriptor associated with a bound PASID.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlbC/gAACgkQdwG7hYl686OY8QCfUPH+IB0zou9/MH3JNMz1ujot
I6wAoK0R4KiOFXvjNeNPy+XroZ9xKqv/
=RM+0
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160216' of git://git.infradead.org/intel-iommu
Pull IOMMU SVM fixes from David Woodhouse:
"Minor register size and interrupt acknowledgement fixes which only
showed up in testing on newer hardware, but mostly a fix to the MM
refcount handling to prevent a recursive refcount issue when mmap() is
used on the file descriptor associated with a bound PASID"
* tag 'for-linus-20160216' of git://git.infradead.org/intel-iommu:
iommu/vt-d: Clear PPR bit to ensure we get more page request interrupts
iommu/vt-d: Fix 64-bit accesses to 32-bit DMAR_GSTS_REG
iommu/vt-d: Fix mm refcounting to hold mm_count not mm_users
3 out of the 5 patches fix a bugzilla.
* fix a race that users reported when we try to load the firmware
and the hardware rfkill interrupt triggers at the same time.
* Luca fixes a very visible bug in scheduled scan: our firmware
doesn't support scheduled scan with no profile configured and
the supplicant sometimes requests such scheduled scans.
* build system fix
* firmware name update for 8265
* typo fix in return value
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tAoG
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2016-02-15' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
These are a few fixes for the current cycle.
3 out of the 5 patches fix a bugzilla.
* fix a race that users reported when we try to load the firmware
and the hardware rfkill interrupt triggers at the same time.
* Luca fixes a very visible bug in scheduled scan: our firmware
doesn't support scheduled scan with no profile configured and
the supplicant sometimes requests such scheduled scans.
* build system fix
* firmware name update for 8265
* typo fix in return value
unintentionally drop bits from the original string - Jason Andryuk
* Add the efi-pstore variables to the variable whitelist so that
users can continue to delete them via efivarfs without needing to
manipulate the immutable flag - Matt Fleming
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=kClF
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI bug fixes from Matt Fleming:
* Fix bugs in our code that converts ucs2 strings to utf8 where we
unintentionally drop bits from the original string (Jason Andryuk)
* Add the efi-pstore variables to the variable whitelist so that
users can continue to delete them via efivarfs without needing to
manipulate the immutable flag (Matt Fleming)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A small clutch of driver specific fixes. The OMAP one is a bit worrying
since it seems to be triggered by some changes in the runtime PM core
code and I suspect there's other drivers across that are going to be
using the same pattern outside of OMAP but nothing seems to be coming up
in the testing people are doing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWwcN2AAoJECTWi3JdVIfQM9IH/2WWGIU4ByQeHLd7FnNHQwZk
wh4g7xpo/SRzob2rz2yqeKgkIg4Ew4+BsD5jslvGhBn9ph5HIFYHVcHt3vjVUNRE
EyOoM8X4lLc97LYog10ieXk5dFkvcCTDYoQDcTxVDmMPRsRrt2Z7htTB4jAbhlk/
kH5nJCir4Cwk5qDTw7+9W8d5hCXl3ESM7KoTCqtvpA8JmTD++vRcphp39NWZejAw
ukO/EAJcwqlTmds3zki1/lM6R4NBtbAE2BGy9j0eUQnL3/37Sl77hAxcsKjey1Zj
dVa8ow9ZRTEZtbCQjrK8WpD3V26TNuUGZs4qEQ+nizQnvAnrqgkfOOg6wBJ6LDg=
=imJW
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small clutch of driver specific fixes.
The OMAP one is a bit worrying since it seems to be triggered by some
changes in the runtime PM core code and I suspect there's other
drivers across that are going to be using the same pattern outside of
OMAP but nothing seems to be coming up in the testing people are
doing"
* tag 'spi-fix-v4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: omap2-mcspi: Fix PM regression with deferred probe for pm_runtime_reinit
spi: bcm2835aux: fix bitmask defines
spi: atmel: fix gpio chip-select in case of non-DT platform
spi/fsl-espi: Correct the maximum transaction length
spi: imx: fix spi resource leak with dma transfer
spi: fix counting in spi-loopback-test code
Pull m68k fixes from Geert Uytterhoeven:
"Summary:
- Wire up new copy_file_range syscall
- Update defconfigs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/defconfig: Update defconfigs for v4.5-rc1
m68k: Wire up copy_file_range
We need to use post-decrement to get the pci_map_page undone also for
i==0, and to avoid some very unpleasant behaviour if pci_map_page
failed already at i==0.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We need to use post-decrement to get the pci_map_page undone also for
i==0, and to avoid some very unpleasant behaviour if pci_map_page
failed already at i==0.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
batman-adv checks in different situation if a new device is already on top
of a different batman-adv device. This is done by getting the iflink of a
device and all its parent. It assumes that this iflink is always a parent
device in an acyclic graph. But this assumption is broken by devices like
veth which are actually a pair of two devices linked to each other. The
recursive check would therefore get veth0 when calling dev_get_iflink on
veth1. And it gets veth0 when calling dev_get_iflink with veth1.
Creating a veth pair and loading batman-adv freezes parts of the system
ip link add veth0 type veth peer name veth1
modprobe batman-adv
An RCU stall will be detected on the system which cannot be fixed.
INFO: rcu_sched self-detected stall on CPU
1: (5264 ticks this GP) idle=3e9/140000000000001/0
softirq=144683/144686 fqs=5249
(t=5250 jiffies g=46 c=45 q=43)
Task dump for CPU 1:
insmod R running task 0 247 245 0x00000008
ffffffff8151f140 ffffffff8107888e ffff88000fd141c0 ffffffff8151f140
0000000000000000 ffffffff81552df0 ffffffff8107b420 0000000000000001
ffff88000e3fa700 ffffffff81540b00 ffffffff8107d667 0000000000000001
Call Trace:
<IRQ> [<ffffffff8107888e>] ? rcu_dump_cpu_stacks+0x7e/0xd0
[<ffffffff8107b420>] ? rcu_check_callbacks+0x3f0/0x6b0
[<ffffffff8107d667>] ? hrtimer_run_queues+0x47/0x180
[<ffffffff8107cf9d>] ? update_process_times+0x2d/0x50
[<ffffffff810873fb>] ? tick_handle_periodic+0x1b/0x60
[<ffffffff810290ae>] ? smp_trace_apic_timer_interrupt+0x5e/0x90
[<ffffffff813bbae2>] ? apic_timer_interrupt+0x82/0x90
<EOI> [<ffffffff812c3fd7>] ? __dev_get_by_index+0x37/0x40
[<ffffffffa0031f3e>] ? batadv_hard_if_event+0xee/0x3a0 [batman_adv]
[<ffffffff812c5801>] ? register_netdevice_notifier+0x81/0x1a0
[...]
This can be avoided by checking if two devices are each others parent and
stopping the check in this situation.
Fixes: b7eddd0b39 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven@narfation.org: rewritten description, extracted fix]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The commit [7f0973e973cd: ALSA: seq: Fix lockdep warnings due to
double mutex locks] split the management of two linked lists (source
and destination) into two individual calls for avoiding the AB/BA
deadlock. However, this may leave the possible double deletion of one
of two lists when the counterpart is being deleted concurrently.
It ends up with a list corruption, as revealed by syzkaller fuzzer.
This patch fixes it by checking the list emptiness and skipping the
deletion and the following process.
BugLink: http://lkml.kernel.org/r/CACT4Y+bay9qsrz6dQu31EcGaH9XwfW7o3oBzSQUG9fMszoh=Sg@mail.gmail.com
Fixes: 7f0973e973 ('ALSA: seq: Fix lockdep warnings due to 'double mutex locks)
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The comparisons should be >= since 0x800 and 0x80 require an additional bit
to store.
For the 3 byte case, the existing shift would drop off 2 more bits than
intended.
For the 2 byte case, there should be 5 bits bits in byte 1, and 6 bits in
byte 2.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Matthew Garrett <mjg59@coreos.com>
Cc: "Lee, Chun-Yi" <jlee@suse.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Laszlo explains why this is a good idea,
'This is because the pstore filesystem can be backed by UEFI variables,
and (for example) a crash might dump the last kilobytes of the dmesg
into a number of pstore entries, each entry backed by a separate UEFI
variable in the above GUID namespace, and with a variable name
according to the above pattern.
Please see "drivers/firmware/efi/efi-pstore.c".
While this patch series will not prevent the user from deleting those
UEFI variables via the pstore filesystem (i.e., deleting a pstore fs
entry will continue to delete the backing UEFI variable), I think it
would be nice to preserve the possibility for the sysadmin to delete
Linux-created UEFI variables that carry portions of the crash log,
*without* having to mount the pstore filesystem.'
There's also no chance of causing machines to become bricked by
deleting these variables, which is the whole purpose of excluding
things from the whitelist.
Use the LINUX_EFI_CRASH_GUID guid and a wildcard '*' for the match so
that we don't have to update the string in the future if new variable
name formats are created for crash dump variables.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Peter Jones <pjones@redhat.com>
Tested-by: Peter Jones <pjones@redhat.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: "Lee, Chun-Yi" <jlee@suse.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
may brick machines. We use a whitelist of known-safe variables to
allow things like installing distributions to work out of the box, and
instead restrict vendor-specific variable deletion by making
non-whitelist variables immutable - Peter Jones
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=F4YT
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fixes from Matt Fleming:
* Prevent accidental deletion of EFI variables through efivarfs that
may brick machines. We use a whitelist of known-safe variables to
allow things like installing distributions to work out of the box, and
instead restrict vendor-specific variable deletion by making
non-whitelist variables immutable (Peter Jones)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Michael Chan