The pci_pm_reset() function is not a very nice interface due to its
limitations and conditional behavior (e.g. it doesn't affect devices
in low-power states), but it cannot be simply dropped, because
existing device drivers may depend on it. However, its behavior and
limitations should be well documented, so add an appropriate
kerneldoc comment to it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 2f671e2d allowed us to clear ASPM state when the FADT
tells us it isn't supported, but we don't put this into effect
if the aspm_policy is set to POLICY_POWERSAVE. Enable the
state to be cleared regardless of policy.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
So in a lot of modern systems, a GPU will always be below a parent bridge that won't share with any other GPUs. This means VGA arbitration on those GPUs can be controlled by using the bridge routing instead of io/mem decodes.
The problem is locating which GPUs share which upstream bridges. This patch attempts to identify all the GPUs which can be controlled via bridges, and ones that can't. This patch endeavours to work out the bridge sharing semantics.
When disabling GPUs via a bridge, it doesn't do irq callbacks or touch the io/mem decodes for the gpu.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.infradead.org/iommu-2.6:
intel_iommu: disable all VT-d PMRs when TXT launched
intel-iommu: Fix get_domain_for_dev() error path
intel-iommu: Unlink domain from iommu
intel-iommu: Fix use after release during device attach
Intel VT-d Protected Memory Regions (PMRs) are supposed to be disabled,
on each VT-d engine, after DMA remapping is enabled on the engines.
This is because the behavior of having both enabled is not deterministic
and because, if TXT has been used to launch the kernel, the PMRs may be
programmed to cover memory regions that will be used for DMA.
Under some circumstances (certain quirks detected, lack of multiple
devices, etc.), the current code does not set up DMA remapping on some
VT-d engines. In such cases it also skips disabling the PMRs. This
causes failures when the kernel is launched with TXT (most often this
occurs on the graphics engine and results in colored vertical bars on
the display).
This patch detects when the kernel has been launched with TXT and then
disables the PMRs on all VT-d engines. In some cases where the reason
that remapping is not being enabled is due to possible ACPI DMAR table
errors, the VT-d engine addresses may not be correct and thus not able
to be safely programmed even to disable PMRs. Because part of the TXT
launch process is the verification of these addresses, it will always be
safe to disable PMRs if the TXT launch has succeeded and hence only
doing this in such cases.
Signed-off-by: Joseph Cihula <joseph.cihula@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: pci-label: Fix build failure when CONFIG_NLS is set to 'm' by allmodconfig
Create a kconfig option symbol for PCI_LABEL and enable it
when DMI || ACPI are enabled.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Xen save/restore is going to use hibernate device callbacks for
quiescing devices and putting them back to normal operations and it
would need to select CONFIG_HIBERNATION for this purpose. However,
that also would cause the hibernate interfaces for user space to be
enabled, which might confuse user space, because the Xen kernels
don't support hibernation. Moreover, it would be wasteful, as it
would make the Xen kernels include a substantial amount of code that
they would never use.
To address this issue introduce new power management Kconfig option
CONFIG_HIBERNATE_CALLBACKS, such that it will only select the code
that is necessary for the hibernate device callbacks to work and make
CONFIG_HIBERNATION select it. Then, Xen save/restore will be able to
select CONFIG_HIBERNATE_CALLBACKS without dragging the entire
hibernate code along with it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Shriram Rajagopalan <rshriram@cs.ubc.ca>
In commit 13583b1659 ("PCI: refactor io size calculation code") Ram
had a thinko in the refactorization of the code: the end result used the
variable 'align' for the bus alignment, but the original code used
'min_align'.
Since then, another use of that 'align' variable got introduced by
commit c8adf9a3e8 ("PCI: pre-allocate additional resources to devices
only after successful allocation of essential resources.")
Fix both of those uses to use 'min_align' as they should.
Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Ram Pai <linuxram@us.ibm.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves the relevant declarations from the local
header file in drivers/pci to a more accessible locations so
that it can be used by the AMD IOMMU driver too.
The file is named pci-ats.h because support for the PCI PRI
capability will also be added there in a later patch-set.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'syscore' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
Introduce ARCH_NO_SYSDEV_OPS config option (v2)
cpufreq: Use syscore_ops for boot CPU suspend/resume (v2)
KVM: Use syscore_ops instead of sysdev class and sysdev
PCI / Intel IOMMU: Use syscore_ops instead of sysdev class and sysdev
timekeeping: Use syscore_ops instead of sysdev class and sysdev
x86: Use syscore_ops instead of sysdev classes and sysdevs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: Disable ASPM when _OSC control is not granted for PCIe services
PCI: Changing ASPM policy, via /sys, to POWERSAVE could cause NMIs
PCI: PCIe links may not get configured for ASPM under POWERSAVE mode
PCI/ACPI: Report ASPM support to BIOS if not disabled from command line
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (42 commits)
ACPI: minor printk format change in acpi_pad
ACPI: make acpi_pad /sys output more readable
ACPICA: Update version to 20110316
ACPICA: Header support for SLIC table
ACPI: Make sure the FADT is at least rev 2 before using the reset register
ACPI: Bug compatibility for Windows on the ACPI reboot vector
ACPICA: Fix access width for reset vector
ACPI battery: fribble sysfs files from a resume notifier
ACPI button: remove unused procfs I/F
ACPI, APEI, Add PCIe AER error information printing support
PCIe, AER, use pre-generated prefix in error information printing
ACPI, APEI, Add ERST record ID cache
ACPI: Use syscore_ops instead of sysdev class and sysdev
ACPI: Remove the unused EC sysdev class
ACPI: use __cpuinit for the acpi_processor_set_pdc() call tree
ACPI: use __init where possible in processor driver
Thermal_Framework-Fix_crash_during_hwmon_unregister
ACPICA: Update version to 20110211.
ACPICA: Add mechanism to defer _REG methods for some installed handlers
ACPICA: Add support for FunctionalFixedHW in acpi_ut_get_region_name
...
- Introduce ns_capable to test for a capability in a non-default
user namespace.
- Teach cap_capable to handle capabilities in a non-default
user namespace.
The motivation is to get to the unprivileged creation of new
namespaces. It looks like this gets us 90% of the way there, with
only potential uid confusion issues left.
I still need to handle getting all caps after creation but otherwise I
think I have a good starter patch that achieves all of your goals.
Changelog:
11/05/2010: [serge] add apparmor
12/14/2010: [serge] fix capabilities to created user namespaces
Without this, if user serge creates a user_ns, he won't have
capabilities to the user_ns he created. THis is because we
were first checking whether his effective caps had the caps
he needed and returning -EPERM if not, and THEN checking whether
he was the creator. Reverse those checks.
12/16/2010: [serge] security_real_capable needs ns argument in !security case
01/11/2011: [serge] add task_ns_capable helper
01/11/2011: [serge] add nsown_capable() helper per Bastian Blank suggestion
02/16/2011: [serge] fix a logic bug: the root user is always creator of
init_user_ns, but should not always have capabilities to
it! Fix the check in cap_capable().
02/21/2011: Add the required user_ns parameter to security_capable,
fixing a compile failure.
02/23/2011: Convert some macros to functions as per akpm comments. Some
couldn't be converted because we can't easily forward-declare
them (they are inline if !SECURITY, extern if SECURITY). Add
a current_user_ns function so we can use it in capability.h
without #including cred.h. Move all forward declarations
together to the top of the #ifdef __KERNEL__ section, and use
kernel-doc format.
02/23/2011: Per dhowells, clean up comment in cap_capable().
02/23/2011: Per akpm, remove unreachable 'return -EPERM' in cap_capable.
(Original written and signed off by Eric; latest, modified version
acked by him)
[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: export current_user_ns() for ecryptfs]
[serge.hallyn@canonical.com: remove unneeded extra argument in selinux's task_has_capability]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Daniel Lezcano <daniel.lezcano@free.fr>
Acked-by: David Howells <dhowells@redhat.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Intel IOMMU subsystem uses a sysdev class and a sysdev for
executing iommu_suspend() after interrupts have been turned off
on the boot CPU (during system suspend) and for executing
iommu_resume() before turning on interrupts on the boot CPU
(during system resume). However, since both of these functions
ignore their arguments, the entire mechanism may be replaced with a
struct syscore_ops object which is simpler.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
The AER error information printing support is implemented in
drivers/pci/pcie/aer/aer_print.c. So some string constants, functions
and macros definitions can be re-used without being exported.
The original PCIe AER error information printing function is not
re-used directly because the overall format is quite different. And
changing the original printing format may make some original users'
scripts broken.
Signed-off-by: Huang Ying <ying.huang@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When printing PCIe AER error information, each line is prefixed with
PCIe device and driver information. In original implementation, the
prefix is generated when each line is printed. In fact, all lines
share the same prefix. So this patch pre-generated the prefix, and
use that one when each line is printed.
In addition to common prefix can be pre-generated, the trailing white
spaces in string constants and NULLs in char * array constants can be
removed too. These can reduce the object file size further.
The size of object file before and after changing is as follow:
text data bss dec
before: 3038 0 0 3038
after: 2118 0 0 2118
Signed-off-by: Huang Ying <ying.huang@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
v3 -> v2: Added text to describe the problem
v2 -> v1: Split this patch from v1
v1 : Part of: http://marc.info/?l=linux-pci&m=130042212003242&w=2
Disable ASPM when no _OSC control for PCIe services is granted
by the BIOS. This is to protect systems with a buggy BIOS that
did not set the ACPI FADT "ASPM Controls" bit even though the
underlying HW can't do ASPM.
To turn "on" ASPM the minimum the BIOS needs to do:
1. Clear the ACPI FADT "ASPM Controls" bit.
2. Support _OSC appropriately
There is no _OSC Control bit for ASPM. However, we expect the BIOS to
support _OSC for a Root Bridge that originates a PCIe hierarchy. If this
is not the case - we are better off not enabling ASPM on that server.
Commit 852972acff (ACPI: Disable ASPM if the
Platform won't provide _OSC control for PCIe) describes the above scenario.
To quote verbatim from there:
[The PCI SIG documentation for the _OSC OS/firmware handshaking interface
states:
"If the _OSC control method is absent from the scope of a host bridge
device, then the operating system must not enable or attempt to use any
features defined in this section for the hierarchy originated by the host
bridge."
The obvious interpretation of this is that the OS should not attempt to use
PCIe hotplug, PME or AER - however, the specification also notes that an
_OSC method is *required* for PCIe hierarchies, and experimental validation
with An Alternative OS indicates that it doesn't use any PCIe functionality
if the _OSC method is missing. That arguably means we shouldn't be using
MSI or extended config space, but right now our problems seem to be limited
to vendors being surprised when ASPM gets enabled on machines when other
OSs refuse to do so. So, for now, let's just disable ASPM if the _OSC
method doesn't exist or refuses to hand over PCIe capability control.]
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
v3 -> v2: Modified the text that describes the problem
v2 -> v1: Returned -EPERM
v1 : http://marc.info/?l=linux-pci&m=130013194803727&w=2
For servers whose hardware cannot handle ASPM the BIOS ought to set the
FADT bit shown below:
In Sec 5.2.9.3 (IA-PC Boot Arch. Flags) of ACPI4.0a Specification, please
see Table 5-11:
PCIe ASPM Controls: If set, indicates to OSPM that it must not enable
OPSM ASPM control on this platform.
However there are shipping servers whose BIOS did not set this bit. (An
example is the HP ProLiant DL385 G6. A Maintenance BIOS will fix that).
For such servers even if a call is made via pci_no_aspm(), based on _OSC
support in the BIOS, it may be too late because the ASPM code may have
already allocated and filled its "link_list".
So if a user sets the ASPM "policy" to "powersave" via /sys then
pcie_aspm_set_policy() will run through the "link_list" and re-configure
ASPM policy on devices that advertise ASPM L0s/L1 capability:
# echo powersave > /sys/module/pcie_aspm/parameters/policy
# cat /sys/module/pcie_aspm/parameters/policy
default performance [powersave]
That can cause NMIs since the hardware doesn't play well with ASPM:
[ 1651.906015] NMI: PCI system error (SERR) for reason b1 on CPU 0.
[ 1651.906015] Dazed and confused, but trying to continue
Ideally, the BIOS should have set that FADT bit in the first place but we
could be more robust - especially given the fact that Windows doesn't
cause NMIs in the above scenario.
There should be a sanity check to not allow a user to modify ASPM policy
when aspm_disabled is set.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
v3 -> v2: Moved ASPM enabling logic to pci_set_power_state()
v2 -> v1: Preserved the logic in pci_raw_set_power_state()
: Added ASPM enabling logic after scanning Root Bridge
: http://marc.info/?l=linux-pci&m=130046996216391&w=2
v1 : http://marc.info/?l=linux-pci&m=130013164703283&w=2
The assumption made in commit 41cd766b06
(PCI: Don't enable aspm before drivers have had a chance to veto it) that
pci_enable_device() will result in re-configuring ASPM when aspm_policy is
POWERSAVE is no longer valid. This is due to commit
97c145f7c8 (PCI: read current power state
at enable time) which resets dev->current_state to D0. Due to this the
call to pcie_aspm_pm_state_change() is never made. Note the equality check
(below) that returns early:
./drivers/pci/pci.c: pci_raw_set_pci_power_state()
546 /* Check if we're already there */
547 if (dev->current_state == state)
548 return 0;
Therefore OSPM never configures the PCIe links for ASPM to turn them "on".
Fix it by configuring ASPM from the pci_enable_device() code path. This
also allows a driver such as the e1000e networking driver a chance to
disable ASPM (L0s, L1), if need be, prior to enabling the device. A
driver may perform this action if the device is known to mis-behave
wrt ASPM.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We need to distinguish the situation in which ASPM support is
disabled from the command line or through .config from the situation
in which it is disabled, because the hardware or BIOS can't handle
it. In the former case we should not report ASPM support to the BIOS
through ACPI _OSC, but in the latter case we should do that.
Introduce pcie_aspm_support_enabled() that can be used by
acpi_pci_root_add() to determine whether or not it should report ASPM
support to the BIOS through _OSC.
Cc: stable@kernel.org
References: https://bugzilla.kernel.org/show_bug.cgi?id=29722
References: https://bugzilla.kernel.org/show_bug.cgi?id=20232
Reported-and-tested-by: Ortwin Glück <odi@odi.ch>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: label: remove #include of ACPI header to avoid warnings
PCI: label: Fix compilation error when CONFIG_ACPI is unset
PCI: pre-allocate additional resources to devices only after successful allocation of essential resources.
PCI: introduce reset_resource()
PCI: data structure agnostic free list function
PCI: refactor io size calculation code
PCI: do not create quirk I/O regions below PCIBIOS_MIN_IO for ICH
PCI hotplug: acpiphp: set current_state to D0 in register_slot
PCI: Export ACPI _DSM provided firmware instance number and string name to sysfs
PCI: add more checking to ICH region quirks
PCI: aer-inject: Override PCIe AER Mask Registers
PCI: fix tlan build when CONFIG_PCI is not enabled
PCI: remove quirk for pre-production systems
PCI: Avoid potential NULL pointer dereference in pci_scan_bridge
PCI/lpc: irq and pci_ids patch for Intel DH89xxCC DeviceIDs
PCI: sysfs: Fix failure path for addition of "vpd" attribute
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/epip/linux-2.6-unicore32: (40 commits)
unicore32: rewrite arch-specific tlb.h to use asm-generic version
unicore32: modify io_p2v and io_v2p macros, and adjust PKUNITY_mmio_BASEs
unicore32: replace unicore32-specific iomap functions with generic lib implementation
unicore32 machine related: add frame buffer driver for pkunity-v3 soc
unicore32 machine related files: add i2c bus drivers for pkunity-v3 soc
unicore32 io: redefine __REG(x) and re-use readl/writel funcs
unicore32 i8042 upgrade and bugfix: adjust resource request region type
unicore32 upgrade to v2.6.38-rc5: add one more paramter for pte_alloc_map call
unicore32 i8042: adjust io funcs of i8042-unicore32io.h
unicore32: rename PKUNITY_IOSPACE_BASE to PKUNITY_MMIO_BASE
unicore32: modify function names and parameters for irq_chips
unicore32: remove unused lines in arch/unicore32/include/asm/irq.h
unicore32 time.c: change calculate method for clock_event_device
unicore32: ADD MAINTAINER for unicore32 architecture
unicore32 machine related files: ps2 driver
unicore32 machine related files: pci bus handling
unicore32 machine related files: hardware registers
unicore32 machine related files: core files
unicore32 additional architecture files: boot process
unicore32 additional architecture files: low-level lib: misc
...
Acked-by: Arnd Bergmann <arnd@arndb.de>
I found that including acpi/apci_drivers.h is not necessary and
introduces these warnings:
In file included from drivers/pci/pci-label.c:32:
include/acpi/acpi_drivers.h:103: warning: ‘struct acpi_device’ declared inside parameter list
include/acpi/acpi_drivers.h:103: warning: its scope is only this definition or declaration, which is probably not what you want
include/acpi/acpi_drivers.h:107: warning: ‘struct acpi_pci_root’ declared inside parameter list
Signed-off-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch fixes compilation error descibed below introduced by
the commit 6058989bad
drivers/pci/pci-label.c: In function ‘pci_create_firmware_label_files’:
drivers/pci/pci-label.c:366:2: error: implicit declaration of function ‘device_has_dsm’
Signed-off-by: Narendra K <narendra_k@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (21 commits)
PM / Hibernate: Reduce autotuned default image size
PM / Core: Introduce struct syscore_ops for core subsystems PM
PM QoS: Make pm_qos settings readable
PM / OPP: opp_find_freq_exact() documentation fix
PM: Documentation/power/states.txt: fix repetition
PM: Make system-wide PM and runtime PM treat subsystems consistently
PM: Simplify kernel/power/Kconfig
PM: Add support for device power domains
PM: Drop pm_flags that is not necessary
PM: Allow pm_runtime_suspend() to succeed during system suspend
PM: Clean up PM_TRACE dependencies and drop unnecessary Kconfig option
PM: Remove CONFIG_PM_OPS
PM: Reorder power management Kconfig options
PM: Make CONFIG_PM depend on (CONFIG_PM_SLEEP || CONFIG_PM_RUNTIME)
PM / ACPI: Remove references to pm_flags from bus.c
PM: Do not create wakeup sysfs files for devices that cannot wake up
USB / Hub: Do not call device_set_wakeup_capable() under spinlock
PM: Use appropriate printk() priority level in trace.c
PM / Wakeup: Don't update events_check_enabled in pm_get_wakeup_count()
PM / Wakeup: Make pm_save_wakeup_count() work as documented
...
After redefining CONFIG_PM to depend on (CONFIG_PM_SLEEP ||
CONFIG_PM_RUNTIME) the CONFIG_PM_OPS option is redundant and can be
replaced with CONFIG_PM.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If we run out of domain_ids and fail iommu_attach_domain(), we
fall into domain_exit() without having setup enough of the
domain structure for this to do anything useful. In fact, it
typically runs off into the weeds walking the bogus domain->devices
list. Just free the domain.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
When we remove a device, we unlink the iommu from the domain, but
we never do the reverse unlinking of the domain from the iommu.
This means that we never clear iommu->domain_ids, eventually leading
to resource exhaustion if we repeatedly bind and unbind a device
to a driver. Also free empty domains to avoid a resource leak.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Linux tries to pre-allocate minimal resources to hotplug bridges. This
works fine as long as there are enough resources to satisfy all other
genuine resource requirements. However if enough resources are not
available to satisfy any of these nice-to-have pre-allocations, the
resource-allocator reports errors and returns failure.
This patch distinguishes between must-have resource from nice-to-have
resource. Any failure to allocate nice-to-have resources are ignored.
This behavior can be particularly useful to trigger automatic
reallocation when the OS discovers genuine allocation-conflicts or
genuine unallocated-requests caused by buggy allocation behavior of the
native BIOS/uEFI.
https://bugzilla.kernel.org/show_bug.cgi?id=15960 captures the
movitation behind the patch. This patch is verified to resolve the above
bug.
changelog v2: o fixed a bug where pci_assign_resource() was called on a
resource of zero resource size.
changelog v3: addressed Bjorn's comment
o "Please don't indent and right-justify the changelog".
o removed add_size from struct resource. The additional
size is now tracked using a linked list.
changelog v4: o moved freeing up of elements in head list from
assign_requested_resources_sorted() to
__assign_resources_sorted().
o removed a wrong reference to 'add_size' in
pbus_size_mem().
o some code optimizations in adjust_resources_sorted()
and assign_requested_resources_sorted()
changelog v5: o moved freeing up of elements in head list from
assign_requested_resources_sorted() to
__assign_resources_sorted().
o removed a wrong reference to 'add_size' in
pbus_size_mem().
o some code optimizations in adjust_resources_sorted()
and assign_requested_resources_sorted()
changelog v5: o factored out common code and made them into
separate independent patches
o added comments in kdoc format
o added a BUG_ON in pci_assign_unassigned_resources()
to catch for memory leak.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Replace free_failed_list() with a free_list() call. free_list() can
handle 'resource_list_x', 'resource_list' and any linked list linked
through ->next
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Refactor code that calculates the io size in pbus_size_io() and
pbus_mem_io() into separate functions.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some broken BIOSes on ICH4 chipset report an ACPI region which is in
conflict with legacy IDE ports when ACPI is disabled. Even though the
regions overlap, IDE ports are working correctly (we cannot find out
the decoding rules on chipsets).
So the only problem is the reported region itself, if we don't reserve
the region in the quirk everything works as expected.
This patch avoids reserving any quirk regions below PCIBIOS_MIN_IO
which is 0x1000. Some regions might be (and are by a fast google
query) below this border, but the only difference is that they won't
be reserved anymore. They should still work though the same as before.
The conflicts look like (1f.0 is bridge, 1f.1 is IDE ctrl):
pci 0000:00:1f.1: address space collision: [io 0x0170-0x0177] conflicts with 0000:00:1f.0 [io 0x0100-0x017f]
At 0x0100 a 128 bytes long ACPI region is reported in the quirk for
ICH4. ata_piix then fails to find disks because the IDE legacy ports
are zeroed:
ata_piix 0000:00:1f.1: device not available (can't reserve [io 0x0000-0x0007])
References: https://bugzilla.novell.com/show_bug.cgi?id=558740
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If a device doesn't support power management (pm_cap == 0) but it is
acpi_pci_power_manageable() because there is a _PS0 method declared for
it and _EJ0 is also declared for the slot then nobody is going to set
current_state = PCI_D0 for this device. This is what I think it is
happening:
pci_enable_device
|
__pci_enable_device_flags
/* here we do not set current_state because !pm_cap */
|
do_pci_enable_device
|
pci_set_power_state
|
__pci_start_power_transition
|
pci_platform_power_transition
/* platform_pci_power_manageable() calls acpi_pci_power_manageable that
* returns true */
|
platform_pci_set_power_state
/* acpi_pci_set_power_state gets called and does nothing because the
* acpi device has _EJ0, see the comment "If the ACPI device has _EJ0,
* ignore the device" */
at this point if we refer to the commit message that introduced the
comment above (10b3dcae0f), it is up to
the hotplug driver to set the state to D0.
However AFAICT the pci hotplug driver never does, in fact
drivers/pci/hotplug/acpiphp_glue.c:register_slot sets the slot flags to
(SLOT_ENABLED | SLOT_POWEREDON) but it does not set the pci device
current state to PCI_D0.
So my proposed fix is also to set current_state = PCI_D0 in
register_slot.
Comments are very welcome.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch exports ACPI _DSM (Device Specific Method) provided firmware
instance number and string name of PCI devices as defined by 'PCI
Firmware Specification Revision 3.1' section 4.6.7.( DSM for Naming a
PCI or PCI Express Device Under Operating Systems) to sysfs.
New files created are:
/sys/bus/pci/devices/.../label which contains the firmware name for
the device in question, and
/sys/bus/pci/devices/.../acpi_index which contains the firmware device type
instance for the given device.
cat /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/acpi_index
1
cat /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/label
Embedded Broadcom 5709C NIC 1
cat /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.1/acpi_index
2
cat /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.1/label
Embedded Broadcom 5709C NIC 2
The ACPI _DSM provided firmware 'instance number' and 'string name' will
be given priority if the firmware also provides 'SMBIOS type 41 device
type instance and string'.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jordan Hargrave <jordan_hargrave@dell.com>
Signed-off-by: Narendra K <narendra_k@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Per ICH4 and ICH6 specs, ACPI and GPIO regions are valid iff ACPI_EN
and GPIO_EN bits are set to 1. Add checks for these bits into the
quirks prior to the region creation.
While at it, name the constants by macros.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I have several systems which have the same problem: The PCIe AER
corrected and uncorrected masks have all the error bits set. This
results in the inablility to test with the aer_inject module & utility
on those systems.
Add the 'aer_mask_override' module parameter which will override the
corrected or uncorrected masks for a PCI device. The mask will have the
bit corresponding to the status passed into the aer_inject() function.
After this patch it is possible to successfully use the aer_inject
utility on those PCI slots.
Successfully tested by me on a Dell and Intel whitebox which exhibited
the mask problem.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The wakeup.run_wake_count ACPI device field is only used by the PCI
runtime PM code to "protect" devices from being prepared for
generating wakeup signals more than once in a row. However, it
really doesn't provide any protection, because (1) all of the
functions it is supposed to protect use their own reference counters
effectively ensuring that the device will be set up for generating
wakeup signals just once and (2) the PCI runtime PM code uses
wakeup.run_wake_count in a racy way, since nothing prevents
acpi_dev_run_wake() from being called concurrently from two different
threads for the same device.
Remove the wakeup.run_wake_count ACPI device field which is
unnecessary, confusing and used in a wrong way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cleanup code. Cosmetic change to make the code look easier
to read.
Reviewed-by: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Check the returned vector values for any values that are
odd or plain incorrect (say vector value zero), and if so
print a warning. Also fixup the return values.
This patch was precipiated by the Xen PCIBack returning the
incorrect values due to how it was retrieving PIRQ values.
This has been fixed in the xen-pciback by
"xen/pciback: Utilize 'xen_pirq_from_irq' to get PIRQ value"
patch.
Reviewed-by: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
flush_scheduled_work() is scheduled for deprecation. Cancel ->op_work
directly instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ryan Wilson <hap9@epoch.ncsc.mil>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Revert commit 7eb93b175d
Author: Yu Zhao <yu.zhao@intel.com>
Date: Fri Apr 3 15:18:11 2009 +0800
PCI: SR-IOV quirk for Intel 82576 NIC
If BIOS doesn't allocate resources for the SR-IOV BARs, zero the Flash
BAR and program the SR-IOV BARs to use the old Flash Memory Space.
Please refer to Intel 82576 Gigabit Ethernet Controller Datasheet
section 7.9.2.14.2 for details.
http://download.intel.com/design/network/datashts/82576_Datasheet.pdf
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This quirk was added before SR-IOV was in production and now all machines that
originally had this issue alreayd have bios updates to correct the issue. The
quirk itself is no longer needed and in fact causes bugs if run. Remove it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Yu Zhao <yu.zhao@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reintroduces commit 47970b1b which was subsequently reverted
as f00eaeea. The original change was broken and caused X startup
failures and generally made privileged processes incapable of reading
device dependent config space. The normal capable() interface returns
true on success, but the LSM interface returns 0 on success. This thinko
is now fixed in this patch, and has been confirmed to work properly.
So, once again...Eric Paris noted that commit de139a3 ("pci: check caps
from sysfs file open to read device dependent config space") caused the
capability check to bypass security modules and potentially auditing.
Rectify this by calling security_capable() when checking the open file's
capabilities for config space reads.
Reported-by: Eric Paris <eparis@redhat.com>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: James Morris <jmorris@namei.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Riesen <raa.lkml@gmail.com>
Cc: Sedat Dilek <sedat.dilek@googlemail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: James Morris <jmorris@namei.org>
This reverts commit 47970b1b2a.
It turns out it breaks several distributions. Looks like the stricter
selinux checks fail due to selinux policies not being set to allow the
access - breaking X, but also lspci.
So while the change was clearly the RightThing(tm) to do in theory, in
practice we have backwards compatibility issues making it not work.
Reported-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: David Airlie <airlied@linux.ie>
Acked-by: Alex Riesen <raa.lkml@gmail.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Paris noted that commit de139a3 ("pci: check caps from sysfs file
open to read device dependent config space") caused the capability check
to bypass security modules and potentially auditing. Rectify this by
calling security_capable() when checking the open file's capabilities
for config space reads.
Reported-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: James Morris <jmorris@namei.org>
pci_add_new_bus() calls pci_alloc_child_bus() which calls pci_alloc_bus()
that allocates memory dynamically with kzalloc(). The return value of
kzalloc() is the pointer that's eventually returned from
pci_add_new_bus(), so since kzalloc() can fail and return NULL so can
pci_add_new_bus(). Thus we may end up dereferencing a NULL pointer in
drivers/pci/probe.c::pci_scan_bridge(). Seems to me we should test for
this and bail out if it happens rather than crashing.
Also removed some trailing whitespace that bugged me while looking at
this.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 280c73d ("PCI: centralize the capabilities code in
pci-sysfs.c") changed the initialisation of the "rom" and "vpd"
attributes, and made the failure path for the "vpd" attribute
incorrect. We must free the new attribute structure (attr), but
instead we currently free dev->vpd->attr. That will normally be NULL,
resulting in a memory leak, but it might be a stale pointer, resulting
in a double-free.
Found by inspection; compile-tested only.
Cc: stable@kernel.org
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Obtain the new pgd pointer before releasing the page containing this
value.
Cc: stable@kernel.org
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/PM: Report wakeup events before resuming devices
PCI/PM: Use pm_wakeup_event() directly for reporting wakeup events
PCI: sysfs: Update ROM to include default owner write access
x86/PCI: make Broadcom CNB20LE driver EMBEDDED and EXPERIMENTAL
x86/PCI: don't use native Broadcom CNB20LE driver when ACPI is available
PCI/ACPI: Request _OSC control once for each root bridge (v3)
PCI: enable pci=bfsort by default on future Dell systems
PCI/PCIe: Clear Root PME Status bits early during system resume
PCI: pci-stub: ignore zero-length id parameters
x86/PCI: irq and pci_ids patch for Intel Patsburg
PCI: Skip id checking if no id is passed
PCI: fix __pci_device_probe kernel-doc warning
PCI: make pci_restore_state return void
PCI: Disable ASPM if BIOS asks us to
PCI: Add mask bit definition for MSI-X table
PCI: MSI: Move MSI-X entry definition to pci_regs.h
Fix up trivial conflicts in drivers/net/{skge.c,sky2.c} that had in the
meantime been converted to not use legacy PCI power management, and thus
no longer use pci_restore_state() at all (and that caused trivial
conflicts with the "make pci_restore_state return void" patch)
Make wakeup events be reported by the PCI subsystem before attempting to
resume devices or queuing up runtime resume requests for them, because
wakeup events should be reported as soon as they have been detected.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After recent changes related to wakeup events pm_wakeup_event()
automatically checks if the given device is configured to signal wakeup,
so pci_wakeup_event() may be a static inline function calling
pm_wakeup_event() directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCI sysfs ROM interface requires an enabling write to access the ROM
image, but the default file mode is 0400. The original proposed patch
adding sysfs ROM support was a true read-only interface, with the
enabling bit coming in as a feature request. I suspect it was simply an
oversight that the file mode didn't get updated to match the API.
Acked-by: Chris Wright <chrisw@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move the evaluation of acpi_pci_osc_control_set() (to request control of
PCI Express native features) into acpi_pci_root_add() to avoid calling
it many times for the same root complex with the same arguments.
Additionally, check if all of the requisite _OSC support bits are set
before calling acpi_pci_osc_control_set() for a given root complex.
References: https://bugzilla.kernel.org/show_bug.cgi?id=20232
Reported-by: Ozan Caglayan <ozan@pardus.org.tr>
Tested-by: Ozan Caglayan <ozan@pardus.org.tr>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'stable/xenbus' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/xenbus: making backend support modular is too complex
xen/pci: Make xen-pcifront be dependent on XEN_XENBUS_FRONTEND
xen/xenbus: fixup checkpatch issues in xenbus_probe*
xen/netfront: select XEN_XENBUS_FRONTEND
xen/xenbus: clean up noise in xenbus_probe_frontend.c
xen/xenbus: clean up noise in xenbus_probe_backend.c
xen/xenbus: clean up noise in xenbus_probe.c
xen/xenbus: cleanup debug noise in xenbus_comms.c
xen/xenbus: clean up error handling
xen/xenbus: make frontend bus GPL
xen/xenbus: make sure backend bus is registered earlier
xenbus/frontend: register bus earlier
xen: remove xen/evtchn.h
xen: add backend driver support
xen: separate out frontend xenbus
Remove kobject.h from files which don't need it, notably,
sched.h and fs.h.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I noticed that PCI Express PMEs don't work on my Toshiba Portege R500
after the system has been woken up from a sleep state by a PME
(through Wake-on-LAN). After some investigation it turned out that
the BIOS didn't clear the Root PME Status bit in the root port that
received the wakeup PME and since the Requester ID was also set in
the port's Root Status register, any subsequent PMEs didn't trigger
interrupts.
This problem can be avoided by clearing the Root PME Status bits in
all PCI Express root ports during early resume. For this purpose,
add an early resume routine to the PCIe port driver and make this
driver be always registered, even if pci_ports_disable is set (in
which case the driver's only function is to provide the early
resume callback).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci-stub uses strsep() to separate list of ids and generates a warning
message when it fails to parse an id. However, not specifying the
parameter results in ids set to an empty string. strsep() happily
returns the empty string as the first token and thus triggers the
warning message spuriously.
Make the tokner ignore zero length ids.
Reported-by: Chris Wright <chrisw@sous-sol.org>
Reported-by: Prasad Joshi <P.G.Joshi@student.reading.ac.uk>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Will get warning when pci stub driver is built-in kenel like:
pci-stub: invalid id string ""
So stop early if no id is passed.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_restore_state only ever returns 0, thus there is no benefit in
having it return any value. Also, a large majority of the callers do
not check the return code of pci_restore_state. Make the
pci_restore_state a void return and avoid the overhead.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We currently refuse to touch the ASPM registers if the BIOS tells us that
ASPM isn't supported. This can cause problems if the BIOS has (for any
reason) enabled ASPM on some devices anyway. Change the code such that we
explicitly clear ASPM if the FADT indicates that ASPM isn't supported,
and make sure we tidy up appropriately on device removal in order to deal
with the hotplug case. If ASPM is disabled because the BIOS doesn't hand
over control then we won't touch the registers.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Then we can use it instead of magic number 1.
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Then it can be used by others.
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If pcie_ports_disabled is set, pcie_port_service_register() returns
error code and select_detection_mode() should not attempt to
unregister dummy_driver and use dummy_slots. It should return
PCIEHP_DETECT_ACPI immediately instead.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32: Make sure we can map all of lowmem if we need to
x86, vt-d: Handle previous faults after enabling fault handling
x86: Enable the intr-remap fault handling after local APIC setup
x86, vt-d: Fix the vt-d fault handling irq migration in the x2apic mode
x86, vt-d: Quirk for masking vtd spec errors to platform error handling logic
x86, xsave: Use alloc_bootmem_align() instead of alloc_bootmem()
bootmem: Add alloc_bootmem_align()
x86, gcc-4.6: Use gcc -m options when building vdso
x86: HPET: Chose a paranoid safe value for the ETIME check
x86: io_apic: Avoid unused variable warning when CONFIG_GENERIC_PENDING_IRQ=n
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix off by one in perf_swevent_init()
perf: Fix duplicate events with multiple-pmu vs software events
ftrace: Have recordmcount honor endianness in fn_ELF_R_INFO
scripts/tags.sh: Add magic for trace-events
tracing: Fix panic when lseek() called on "trace" opened for writing
This reverts commit b126b4703a.
We're going back to the old behavior of allocating from bus resources
in _CRS order.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reverts commit 82e3e767c2.
We're going back to considering bus resources in the order we found
them (in _CRS order, when we're using _CRS), so we don't need to
define any ordering.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I wrote this quirk awhile ago to properly setup MCP55 chips on hypertransport
busses so that interrupts reached whatever cpu happend to boot the kdump kernel.
while that works well, it was recently shown to me that a a non-hypertransport
variant of the MCP55 exists, and on those system the register that this quirk
manipulates causes hangs if you write to it. Since the quirk was only meant to
handle errors found on MCP55 chips that have a HT interface, this patch adds a
filter to make sure the chip is an HT capable before making the needed register
adjustment. This lets the broken MCP55s work with kdump while not breaking the
non-HT variants.
Resolves https://bugzilla.kernel.org/show_bug.cgi?id=23952
Tested successfully by the reporter and myself.
Cc: stable@kernel.org
Reported-by: Mathieu Bérard <mathieu@mberard.eu>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fault handling is getting enabled after enabling the interrupt-remapping (as
the success of interrupt-remapping can affect the apic mode and hence the
fault handling mode).
Hence there can potentially be some faults between the window of enabling
interrupt-remapping in the vt-d and the fault-handling of the vt-d units.
Handle any previous faults after enabling the vt-d fault handling.
For v2.6.38 cleanup, need to check if we can remove the dmar_fault() in the
enable_intr_remapping() and see if we can enable fault handling along with
enabling intr-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20101201062244.630417138@intel.com>
Cc: stable@kernel.org [v2.6.32+]
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
On platforms with Intel 7500 chipset, there were some reports of system
hang/NMI's during kexec/kdump in the presence of interrupt-remapping enabled.
During kdump, there is a window where the devices might be still using old
kernel's interrupt information, while the kdump kernel is coming up. This can
cause vt-d faults as the interrupt configuration from the old kernel map to
null IRTE entries in the new kernel etc. (with out interrupt-remapping enabled,
we still have the same issue but in this case we will see benign spurious
interrupt hit the new kernel).
Based on platform config settings, these platforms seem to generate NMI/SMI
when a vt-d fault happens and there were reports that the resulting SMI causes
the system to hang.
Fix it by masking vt-d spec defined errors to platform error reporting logic.
VT-d spec related errors are already handled by the VT-d OS code, so need to
report the same error through other channels.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1291667190.2675.8.camel@sbsiddha-MOBL3.sc.intel.com>
Cc: stable@kernel.org [v2.6.32+]
Reported-by: Max Asbock <masbock@linux.vnet.ibm.com>
Reported-and-tested-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
pci root complex: support for tile architecture
drivers/net/tile/: on-chip network drivers for the tile architecture
MAINTAINERS: add drivers/char/hvc_tile.c as maintained by tile
This change enables PCI root complex support for TILEPro. Unlike
TILE-Gx, TILEPro has no support for memory-mapped I/O, so the PCI
support consists of hypervisor upcalls for PIO, DMA, etc. However,
the performance is fine for the devices we have tested with so far
(1Gb Ethernet, SATA, etc.).
The <asm/io.h> header was tweaked to be a little bit more aggressive
about disabling attempts to map/unmap IO port space. The hacky
<asm/pci-bridge.h> header was rolled into the <asm/pci.h> header
and the result was simplified. Both of the latter two headers were
preliminary versions not meant for release before now - oh well.
There is one quirk for our TILEmpower platform, which accidentally
negotiates up to 5GT and needs to be kicked down to 2.5GT.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I just loaded 2.6.37-rc2 on my machines, and I noticed that X no longer starts.
Running an strace of the X server shows that it's doing this:
open("/sys/bus/pci/devices/0000:07:00.0/resource0", O_RDWR) = 10
mmap(NULL, 16777216, PROT_READ|PROT_WRITE, MAP_SHARED, 10, 0) = -1 EINVAL (Invalid argument)
This code seems to be asking for a shared read/write mapping of 16MB worth of
BAR0 starting at file offset 0, and letting the kernel assign a starting
address. Unfortunately, this -EINVAL causes X not to start. Looking into
dmesg, there's a complaint like so:
process "Xorg" tried to map 0x01000000 bytes at page 0x00000000 on 0000:07:00.0 BAR 0 (start 0x 96000000, size 0x 1000000)
...with the following code in pci_mmap_fits:
pci_start = (mmap_api == PCI_MMAP_SYSFS) ?
pci_resource_start(pdev, resno) >> PAGE_SHIFT : 0;
if (start >= pci_start && start < pci_start + size &&
start + nr <= pci_start + size)
It looks like the logic here is set up such that when the mmap call comes via
sysfs, the check in pci_mmap_fits wants vma->vm_pgoff to be between the
resource's start and end address, and the end of the vma to be no farther than
the end. However, the sysfs PCI resource files always start at offset zero,
which means that this test always fails for programs that mmap the sysfs files.
Given the comment in the original commit
3b519e4ea6, I _think_ the old procfs files
require that the file offset be equal to the resource's base address when
mmapping.
I think what we want here is for pci_start to be 0 when mmap_api ==
PCI_MMAP_PROCFS. The following patch makes that change, after which the Matrox
and Mach64 X drivers work again.
Acked-by: Martin Wilck <martin.wilck@ts.fujitsu.com>
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: sysfs: fix printk warnings
PCI: fix pci_bus_alloc_resource() hang, prefer positive decode
PCI: read current power state at enable time
PCI: fix size checks for mmap() on /proc/bus/pci files
x86/PCI: coalesce overlapping host bridge windows
PCI hotplug: ibmphp: Add check to prevent reading beyond mapped area
Cast pci_resource_start() and pci_resource_len() to u64 for printk.
drivers/pci/pci-sysfs.c:753: warning: format '%16Lx' expects type 'long long unsigned int', but argument 9 has type 'resource_size_t'
drivers/pci/pci-sysfs.c:753: warning: format '%16Lx' expects type 'long long unsigned int', but argument 10 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When a PCI bus has two resources with the same start/end, e.g.,
pci_bus 0000:04: resource 2 [mem 0xd0000000-0xd7ffffff pref]
pci_bus 0000:04: resource 7 [mem 0xd0000000-0xd7ffffff]
the previous pci_bus_find_resource_prev() implementation would alternate
between them forever:
pci_bus_find_resource_prev(... [mem 0xd0000000-0xd7ffffff pref])
returns [mem 0xd0000000-0xd7ffffff]
pci_bus_find_resource_prev(... [mem 0xd0000000-0xd7ffffff])
returns [mem 0xd0000000-0xd7ffffff pref]
pci_bus_find_resource_prev(... [mem 0xd0000000-0xd7ffffff pref])
returns [mem 0xd0000000-0xd7ffffff]
...
This happened because there was no ordering between two resources with the
same start and end. A resource that had the same start and end as the
cursor, but was not itself the cursor, was considered to be before the
cursor.
This patch fixes the hang by making a fixed ordering between any two
resources.
In addition, it tries to allocate from positively decoded regions before
using any subtractively decoded resources. This means we will use a
positive decode region before a subtractive decode one, even if it means
using a smaller address.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=22062
Reported-by: Borislav Petkov <bp@amd64.org>
Tested-by: Borislav Petkov <bp@amd64.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When we enable a PCI device, we avoid doing a lot of the initial setup
work if the device's enable count is non-zero. If we don't fetch the
power state though, we may later fail to set up MSI due to the unknown
status. So pick it up before we short circuit the rest due to a
pre-existing enable or mismatched enable/disable pair (as happens with
VGA devices, which are special in a special way).
Tested-by: Jesse Brandeburg <jesse.brandeburg@gmail.com>
Reported-by: Dave Airlie <airlied@linux.ie>
Tested-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The checks for valid mmaps of PCI resources made through /proc/bus/pci files
that were introduced in 9eff02e204 have several
problems:
1. mmap() calls on /proc/bus/pci files are made with real file offsets > 0,
whereas under /sys/bus/pci/devices, the start of the resource corresponds
to offset 0. This may lead to false negatives in pci_mmap_fits(), which
implicitly assumes the /sys/bus/pci/devices layout.
2. The loop in proc_bus_pci_mmap doesn't skip empty resouces. This leads
to false positives, because pci_mmap_fits() doesn't treat empty resources
correctly (the calculated size is 1 << (8*sizeof(resource_size_t)-PAGE_SHIFT)
in this case!).
3. If a user maps resources with BAR > 0, pci_mmap_fits will emit bogus
WARNINGS for the first resources that don't fit until the correct one is found.
On many controllers the first 2-4 BARs are used, and the others are empty.
In this case, an mmap attempt will first fail on the non-empty BARs
(including the "right" BAR because of 1.) and emit bogus WARNINGS because
of 3., and finally succeed on the first empty BAR because of 2.
This is certainly not the intended behaviour.
This patch addresses all 3 issues.
Updated with an enum type for the additional parameter for pci_mmap_fits().
Cc: stable@kernel.org
Signed-off-by: Martin Wilck <martin.wilck@ts.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
While testing various randconfigs with ktest.pl, I hit the following panic:
BUG: unable to handle kernel paging request at f7e54b03
IP: [<c0d63409>] ibmphp_access_ebda+0x101/0x19bb
Adding printks, I found that the loop that reads the ebda blocks
can move out of the mapped section.
ibmphp_access_ebda: start=f7e44c00 size=5120 end=f7e46000
ibmphp_access_ebda: io_mem=f7e44d80 offset=384
ibmphp_access_ebda: io_mem=f7e54b03 offset=65283
The start of the iomap was at f7e44c00 and had a size of 5120,
making the end f7e46000. We start with an offset of 0x180 or
384, giving the first read at 0xf7e44d80. Reading that location
yields 65283, which is much bigger than the 5120 that was allocated
and makes the next read at f7e54b03 which is outside the mapped area.
Perhaps this is a bug in the driver, or buggy hardware, but this patch
is more about not crashing my box on start up and just giving a warning
if it detects this error.
This patch at least lets my box boot with just a warning.
Cc: Chandru Siddalingappa <chandru@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stanse found that when pdev is found and has no driver a reference is
leaked in pcifront_common_process. So add pci_dev_put there. For the
pdev == NULL case, pci_dev_put(NULL) is fine.
[v2: Updated to not dereference pcidev->dev per Milton's observation]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Milton Miller <miltonm@bga.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
In drivers/pci/xen-pcifront.c the xen/xenbus.h header is included twice -
once is enough.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
and branch 'for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm
* 'for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
xen: register xen pci notifier
xen: initialize cpu masks for pv guests in xen_smp_init
xen: add a missing #include to arch/x86/pci/xen.c
xen: mask the MTRR feature from the cpuid
xen: make hvc_xen console work for dom0.
xen: add the direct mapping area for ISA bus access
xen: Initialize xenbus for dom0.
xen: use vcpu_ops to setup cpu masks
xen: map a dummy page for local apic and ioapic in xen_set_fixmap
xen: remap MSIs into pirqs when running as initial domain
xen: remap GSIs as pirqs when running as initial domain
xen: introduce XEN_DOM0 as a silent option
xen: map MSIs into pirqs
xen: support GSI -> pirq remapping in PV on HVM guests
xen: add xen hvm acpi_register_gsi variant
acpi: use indirect call to register gsi in different modes
xen: implement xen_hvm_register_pirq
xen: get the maximum number of pirqs from xen
xen: support pirq != irq
* 'stable/xen-pcifront-0.8.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (27 commits)
X86/PCI: Remove the dependency on isapnp_disable.
xen: Update Makefile with CONFIG_BLOCK dependency for biomerge.c
MAINTAINERS: Add myself to the Xen Hypervisor Interface and remove Chris Wright.
x86: xen: Sanitse irq handling (part two)
swiotlb-xen: On x86-32 builts, select SWIOTLB instead of depending on it.
MAINTAINERS: Add myself for Xen PCI and Xen SWIOTLB maintainer.
xen/pci: Request ACS when Xen-SWIOTLB is activated.
xen-pcifront: Xen PCI frontend driver.
xenbus: prevent warnings on unhandled enumeration values
xenbus: Xen paravirtualised PCI hotplug support.
xen/x86/PCI: Add support for the Xen PCI subsystem
x86: Introduce x86_msi_ops
msi: Introduce default_[teardown|setup]_msi_irqs with fallback.
x86/PCI: Export pci_walk_bus function.
x86/PCI: make sure _PAGE_IOMAP it set on pci mappings
x86/PCI: Clean up pci_cache_line_size
xen: fix shared irq device passthrough
xen: Provide a variant of xen_poll_irq with timeout.
xen: Find an unbound irq number in reverse order (high to low).
xen: statically initialize cpu_evtchn_mask_p
...
Fix up trivial conflicts in drivers/pci/Makefile
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
x86: allocate space within a region top-down
x86: update iomem_resource end based on CPU physical address capabilities
x86/PCI: allocate space from the end of a region, not the beginning
PCI: allocate bus resources from the top down
resources: support allocating space within a region from the top down
resources: handle overflow when aligning start of available area
resources: ensure callback doesn't allocate outside available space
resources: factor out resource_clip() to simplify find_resource()
resources: add a default alignf to simplify find_resource()
x86/PCI: MMCONFIG: fix region end calculation
PCI: Add support for polling PME state on suspended legacy PCI devices
PCI: Export some PCI PM functionality
PCI: fix message typo
PCI: log vendor/device ID always
PCI: update Intel chipset names and defines
PCI: use new ccflags variable in Makefile
PCI: add PCI_MSIX_TABLE/PBA defines
PCI: add PCI vendor id for STmicroelectronics
x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs
PCI: OLPC: Only enable PCI configuration type override on XO-1
...
The BKL was pushed into this function when it was converted to use the
unlocked_ioctl interface, but nothing that the function touches is
actually protected by the BKL. So just remove the BKL entirely, so that
we finally can get a realistic system build without the BKL being
enabled at all.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allocate space from the highest-address PCI bus resource first, then work
downward.
Previously, we looked for space in PCI host bridge windows in the order
we discovered the windows. For example, given the following windows
(discovered via an ACPI _CRS method):
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000effff]
pci_root PNP0A03:00: host bridge window [mem 0x000f0000-0x000fffff]
pci_root PNP0A03:00: host bridge window [mem 0xbff00000-0xf7ffffff]
pci_root PNP0A03:00: host bridge window [mem 0xff980000-0xff980fff]
pci_root PNP0A03:00: host bridge window [mem 0xff97c000-0xff97ffff]
pci_root PNP0A03:00: host bridge window [mem 0xfed20000-0xfed9ffff]
we attempted to allocate from [mem 0x000a0000-0x000bffff] first, then
[mem 0x000c0000-0x000effff], and so on.
With this patch, we allocate from [mem 0xff980000-0xff980fff] first, then
[mem 0xff97c000-0xff97ffff], [mem 0xfed20000-0xfed9ffff], etc.
Allocating top-down follows Windows practice, so we're less likely to
trip over BIOS defects in the _CRS description.
On the machine above (a Dell T3500), the [mem 0xbff00000-0xbfffffff] region
doesn't actually work and is likely a BIOS defect. The symptom is that we
move the AHCI controller to 0xbff00000, which leads to "Boot has failed,
sleeping forever," a BUG in ahci_stop_engine(), or some other boot failure.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=16228#c43
Reference: https://bugzilla.redhat.com/show_bug.cgi?id=620313
Reference: https://bugzilla.redhat.com/show_bug.cgi?id=629933
Reported-by: Brian Bloniarz <phunge0@hotmail.com>
Reported-and-tested-by: Stefan Becker <chemobejk@gmail.com>
Reported-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: remove in_workqueue_context()
workqueue: Clarify that schedule_on_each_cpu is synchronous
memory_hotplug: drop spurious calls to flush_scheduled_work()
shpchp: update workqueue usage
pciehp: update workqueue usage
isdn/eicon: don't call flush_scheduled_work() from diva_os_remove_soft_isr()
workqueue: add and use WQ_MEM_RECLAIM flag
workqueue: fix HIGHPRI handling in keep_working()
workqueue: add queue_work and activate_work trace points
workqueue: prepare for more tracepoints
workqueue: implement flush[_delayed]_work_sync()
workqueue: factor out start_flush_work()
workqueue: cleanup flush/cancel functions
workqueue: implement alloc_ordered_workqueue()
Fix up trivial conflict in fs/gfs2/main.c as per Tejun
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
block: autoconvert trivial BKL users to private mutex
drivers: autoconvert trivial BKL users to private mutex
ipmi: autoconvert trivial BKL users to private mutex
mac: autoconvert trivial BKL users to private mutex
mtd: autoconvert trivial BKL users to private mutex
scsi: autoconvert trivial BKL users to private mutex
Fix up trivial conflicts (due to addition of private mutex right next to
deletion of a version string) in drivers/char/pcmcia/cm40[04]0_cs.c
This is a port of the 2.6.18 Xen PCI front driver with fixes
to make it build under 2.6.34 and later (for the full list of
changes: git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen.git
historic/xen-pcifront-0.1). It also includes the fixes
to make it work properly.
[v2: Updated Kconfig, removed crud, added Reviewed-by]
[v3: Added 'static', fixed grant table leak, redid Kconfig]
[v4: Added one more 'static' and removed comments]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Jan Beulich <JBeulich@novell.com>
Introduce an override for the arch_[teardown|setup]_msi_irqs
that can be utilized to fallback to the default arch_* code.
If a platform wants to utilize the code paths defined
in driver/pci/msi.c it has to define HAVE_DEFAULT_MSI_TEARDOWN_IRQS
or HAVE_DEFAULT_MSI_SETUP_IRQS. Otherwise the old mechanism
of over-ridding the arch_* works fine.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: x86@kernel.org
In preperation of modularizing Xen-pcifront the pci_walk_bus
needs to be exported so that the xen-pcifront module can walk
call the pci subsystem to walk the PCI devices and claim them.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> [http://marc.info/?l=linux-pci&m=126149958010298&w=2]
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* Rename shpchp_wq to shpchp_ordered_wq and add non-ordered shpchp_wq
which is used instead of the system workqueue. This is to remove
the use of flush_scheduled_work() which is deprecated and scheduled
for removal.
* With cmwq in place, there's no point in creating workqueues lazily.
Create both shpchp_wq and shpchp_ordered_wq upfront.
* Include workqueue.h from shpchp.h.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* Rename pciehp_wq to pciehp_ordered_wq and add non-ordered pciehp_wq
which is used instead of the system workqueue. This is to remove
the use of flush_scheduled_work() which is deprecated and scheduled
for removal.
* With cmwq in place, there's no point in creating workqueues lazily.
Create both pciehp_wq and pciehp_ordered_wq upfront.
* Include workqueue.h from pciehp.h.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Not all hardware vendors hook up the PME line for legacy PCI devices,
meaning that wakeup events get lost. The only way around this is to poll
the devices to see if their state has changed, so add support for doing
that on legacy PCI devices that aren't part of the core chipset.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It's helpful to have some extra PCI power management functions available to
platform code, so move the declarations to an exported header.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Previously we had to have CONFIG_PCI_DEBUG=y or CONFIG_DYNAMIC_DEBUG=y
to turn on this printk, but I think the IDs are valuable enough that it's
worth putting them in the log always.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These are already defined in pcilib's pci/header.h but not in kernel's
linux/pci_regs.h. Copy them to avoid using magic numbers.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A long time ago I worked on a RHEL5 bug in which kdump hung during boot
on a set of systems. The systems hung because they never received timer
interrupts during calibrate_delay. These systems also all had Opteron
processors on a hypertransport bus, bridged to a pci bus via an Nvidia
MCP55 northbridge chip. After much wrangling I managed to learn from
Nvidia that they have an undocumented register in some versions of that
chip which control how legacy interrupts are send to the cpu complex
when the ioapic isn't active. Nvidia defaults this register to only
send legacy interrupts to the BSP, so if kdump happens to boot on an AP,
we never get timer interrupts and boom. I had initially used this quirk
as a workaround, with my intent being to move apic initalization to an
earlier point in the boot process, so the setting of the register would
be irrelevant. Given the work involved in doing that however, the
fragile nature of the apic initalization code, and the fact that, over
the 2 years since we found this bug, the MCP55 is the only chip which
seems to have this issue, I've figure at this point its likely safer to
just carry the quirk around. By setting the referenced bits in this
hidden register, interrupts will be broadcast to all cpus when the
ioapic isn't active on the above described systems.
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is a design issue related to PCIe AER and _OSC that the BIOS
may be asked to grant control of the AER service even if some
Hardware Error Source Table (HEST) entries contain information
meaning that the BIOS really should control it. Namely,
pcie_port_acpi_setup() calls pcie_aer_get_firmware_first() that
determines whether or not the AER service should be controlled by
the BIOS on the basis of the HEST information for the given PCIe
port. The BIOS is asked to grant control of the AER service for
a PCIe Root Complex if pcie_aer_get_firmware_first() returns 'false'
for at least one root port in that complex, even if all of the other
root ports' HEST entries have the FIRMWARE_FIRST flag set (and none
of them has the GLOBAL flag set). However, if the AER service is
controlled by the kernel, that may interfere with the BIOS' handling
of the error sources having the FIRMWARE_FIRST flag. Moreover,
there may be PCIe endpoints that have the FIRMWARE_FIRST flag set in
HEST and are attached to the root ports in question, in which case it
also may be unsafe to ask the BIOS for control of the AER service.
For this reason, introduce a function checking if there's at least
one PCIe-related HEST entry with the FIRMWARE_FIRST flag set and
disable the native AER service altogether if this function returns
'true'.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Get rid of init_MUTEX[_LOCKED]() and use sema_init() instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
quiet the warning about use of uninitialized e_src in
aer_isr() e_src is initialized by get_e_source()
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
All operations in the pci procfs ioctl functions are
atomic, so no lock is needed here.
Also add a compat_ioctl method, since all the commands
are compatible in 32 bit mode.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Indent the branch of an if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
irq_2_iommu is in struct irq_cfg, so we can do the irq_remapped check
based on irq_cfg instead of going through a lookup function. That's
especially interesting in the eoi_ioapic_irq() hotpath.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Switch the intr_remapping code to use the irq_2_iommu struct in
irg_cfg.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
That interrupt remapping code is x86 specific and tied to the io_apic
code. No need for separate allocator functions in the interrupt
remapping code. This allows to simplify the code and irq_2_iommu is
small (13 bytes on 64bit) so it's not a real problem even if interrupt
remapping is runtime disabled. If it's compile time disabled the
impact is zero.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
No need to dereference irq_desc.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
With SPARSE_IRQ=y the irte descriptors are dynamically allocated, but not
freed in free_irte().
That was ok as long as the sparse irq core was not freeing irq descriptors on
destroy_irq(). Now we leak the irte descriptor. Free it in free_irte().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Handing down irq_desc to msi just so that msi can access
irq_desc.irq_data.msi_desc is a pretty stupid idea. The calling code
can hand down a pointer to msi_desc so msi code does not need to know
about the irq descriptor at all.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
These drivers do not seem to be under active
maintainance from my brief investigation. Apologies
to those maintainers that I have missed.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* git://git.infradead.org/iommu-2.6:
intel-iommu: Use symbolic values instead of magic numbers in Lenovo w/a
intel-iommu: Abort IOMMU setup for igfx if BIOS gave no shadow GTT space
When the Lenovo Ideapad S10-3 is booted with HT enabled,
it hits a boot hang in the intel_idle driver.
This occurs when entering ATM-C4 for the first time,
unless BM_STS is first cleared.
acpi_idle doesn't see this because it first checks
and clears BM_STS, but it would hit the same hang
if that check were disabled.
http://bugs.meego.com/show_bug.cgi?id=7093https://bugs.launchpad.net/ubuntu/+source/linux/+bug/634702
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/pci/intel-iommu.c: In function `__iommu_calculate_agaw':
drivers/pci/intel-iommu.c:437: sorry, unimplemented: inlining failed in call to 'width_to_agaw': function body not available
drivers/pci/intel-iommu.c:445: sorry, unimplemented: called from here
Move the offending function (and its siblings) to top-of-file, remove the
forward declaration.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=17441
Reported-by: Martin Mokrejs <mmokrejs@ribosome.natur.cuni.cz>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 9eecabcb9a ("intel-iommu: Abort
IOMMU setup for igfx if BIOS gave no shadow GTT space") uses a bunch of
magic numbers. Provide #defines for those to make it look slightly saner.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes the prototype for both pci_resource_alignment() and
pci_sriov_resource_alignment().
Patch started as debugging effort from Cam Macdonell.
Cc: Cam Macdonell <cam@cs.ualberta.ca>
Cc: Avi Kivity <avi@redhat.com>
[chrisw: add iov bits]
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: bus speed strings should be const
PCI hotplug: Fix build with CONFIG_ACPI unset
PCI: PCIe: Remove the port driver module exit routine
PCI: PCIe: Move PCIe PME code to the pcie directory
PCI: PCIe: Disable PCIe port services during port initialization
PCI: PCIe: Ask BIOS for control of all native services at once
ACPI/PCI: Negotiate _OSC control bits before requesting them
ACPI/PCI: Do not preserve _OSC control bits returned by a query
ACPI/PCI: Make acpi_pci_query_osc() return control bits
ACPI/PCI: Reorder checks in acpi_pci_osc_control_set()
PCI: PCIe: Introduce commad line switch for disabling port services
PCI: PCIe AER: Introduce pci_aer_available()
x86/PCI: only define pci_domain_nr if PCI and PCI_DOMAINS are set
PCI: provide stub pci_domain_nr function for !CONFIG_PCI configs
We return 1 if the IOMMU has been detected. Zero or an error number
if we failed to find it. This is in preperation of using the IOMMU_INIT
so that we can detect whether an IOMMU is present. I have not
tested this for regression on Calgary, nor on AMD Vi chipsets as
I don't have that hardware.
CC: Muli Ben-Yehuda <muli@il.ibm.com>
CC: "Jon D. Mason" <jdmason@kudzu.us>
CC: "Darrick J. Wong" <djwong@us.ibm.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: David Woodhouse <David.Woodhouse@intel.com>
CC: Chris Wright <chrisw@sous-sol.org>
CC: Yinghai Lu <yinghai@kernel.org>
CC: Joerg Roedel <joerg.roedel@amd.com>
CC: H. Peter Anvin <hpa@zytor.com>
CC: Fujita Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
LKML-Reference: <1282845485-8991-3-git-send-email-konrad.wilk@oracle.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
One of the recent changes caused complilation of
drivers/pci/hotplug/pciehp_core.c to fail. Fix this issue.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCIe port driver's module exit routine is never used, so drop it.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCIe PME code only consists of one file, so it doesn't need to
occupy its own directory. Move it to drivers/pci/pcie/pme.c and
remove the contents of drivers/pci/pcie/pme .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In principle PCIe port services may be enabled by the BIOS, so it's
better to disable them during port initialization to avoid spurious
events from being generated.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After commit 852972acff (ACPI: Disable
ASPM if the platform won't provide _OSC control for PCIe) control of
the PCIe Capability Structure is unconditionally requested by
acpi_pci_root_add(), which in principle may cause problems to
happen in two ways. First, the BIOS may refuse to give control of
the PCIe Capability Structure if it is not asked for any of the
_OSC features depending on it at the same time. Second, the BIOS may
assume that control of the _OSC features depending on the PCIe
Capability Structure will be requested in the future and may behave
incorrectly if that doesn't happen. For this reason, control of
the PCIe Capability Structure should always be requested along with
control of any other _OSC features that may depend on it (ie. PCIe
native PME, PCIe native hot-plug, PCIe AER).
Rework the PCIe port driver so that (1) it checks which native PCIe
port services can be enabled, according to the BIOS, and (2) it
requests control of all these services simultaneously. In
particular, this causes pcie_portdrv_probe() to fail if the BIOS
refuses to grant control of the PCIe Capability Structure, which
means that no native PCIe port services can be enabled for the PCIe
Root Complex the given port belongs to. If that happens, ASPM is
disabled to avoid problems with mishandling it by the part of the
PCIe hierarchy for which control of the PCIe Capability Structure
has not been received.
Make it possible to override this behavior using 'pcie_ports=native'
(use the PCIe native services regardless of the BIOS response to the
control request), or 'pcie_ports=compat' (do not use the PCIe native
services at all).
Accordingly, rework the existing PCIe port service drivers so that
they don't request control of the services directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It is possible that the BIOS will not grant control of all _OSC
features requested via acpi_pci_osc_control_set(), so it is
recommended to negotiate the final set of _OSC features with the
query flag set before calling _OSC to request control of these
features.
To implement it, rework acpi_pci_osc_control_set() so that the caller
can specify the mask of _OSC control bits to negotiate and the mask
of _OSC control bits that are absolutely necessary to it. Then,
acpi_pci_osc_control_set() will run _OSC queries in a loop until
the mask of _OSC control bits returned by the BIOS is equal to the
mask passed to it. Also, before running the _OSC request
acpi_pci_osc_control_set() will check if the caller's required
control bits are present in the final mask.
Using this mechanism we will be able to avoid situations in which the
BIOS doesn't grant control of certain _OSC features, because they
depend on some other _OSC features that have not been requested.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce kernel command line switch pcie_ports= allowing one to
disable all of the native PCIe port services, so that PCIe ports
are treated like PCI-to-PCI bridges.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce a function allowing the caller to check whether to try to
enable PCIe AER.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
drivers/pci/intel-iommu.c: In function 'dma_pte_addr':
drivers/pci/intel-iommu.c:239: warning: passing argument 1 of '__cmpxchg64' from incompatible pointer type
It seems that __cmpxchg64() now cares about the type of its pointer argument,
so give it a (uint64_t *) instead of a pointer to a structure which contains
only that.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Allow disabling the source id checking while programming the interrupt
remap table entry. Useful for debugging or working around the broken
source id checks on some platforms.
Signed-off-by: Chris Wright <chrisw@redhat.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (27 commits)
ACPI / ACPICA: Simplify acpi_ev_initialize_gpe_block()
ACPI / ACPICA: Fail acpi_gpe_wakeup() if ACPI_GPE_CAN_WAKE is unset
ACPI / ACPICA: Do not execute _PRW methods during initialization
ACPI: Fix bogus GPE test in acpi_bus_set_run_wake_flags()
ACPICA: Update version to 20100702
ACPICA: Fix for Alias references within Package objects
ACPICA: Fix lint warning for 64-bit constant
ACPICA: Remove obsolete GPE function
ACPICA: Update debug output components
ACPICA: Add support for WDDT - Watchdog Descriptor Table
ACPICA: Drop acpi_set_gpe
ACPICA: Use low-level GPE enable during GPE block initialization
ACPI / EC: Do not use acpi_set_gpe
ACPI / EC: Drop suspend and resume routines
ACPICA: Remove wakeup GPE reference counting which is not used
ACPICA: Introduce acpi_gpe_wakeup()
ACPICA: Rename acpi_hw_gpe_register_bit
ACPICA: Update version to 20100528
ACPICA: Add signatures for undefined tables: ATKG, GSCI, IEIT
ACPICA: Optimization: Reduce the number of namespace walks
...
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (30 commits)
PCI: update for owner removal from struct device_attribute
PCI: Fix warnings when CONFIG_DMI unset
PCI: Do not run NVidia quirks related to MSI with MSI disabled
x86/PCI: use for_each_pci_dev()
PCI: use for_each_pci_dev()
PCI: MSI: Restore read_msi_msg_desc(); add get_cached_msi_msg_desc()
PCI: export SMBIOS provided firmware instance and label to sysfs
PCI: Allow read/write access to sysfs I/O port resources
x86/PCI: use host bridge _CRS info on ASRock ALiveSATA2-GLAN
PCI: remove unused HAVE_ARCH_PCI_SET_DMA_MAX_SEGMENT_{SIZE|BOUNDARY}
PCI: disable mmio during bar sizing
PCI: MSI: Remove unsafe and unnecessary hardware access
PCI: Default PCIe ASPM control to on and require !EMBEDDED to disable
PCI: kernel oops on access to pci proc file while hot-removal
PCI: pci-sysfs: remove casts from void*
ACPI: Disable ASPM if the platform won't provide _OSC control for PCIe
PCI hotplug: make sure child bridges are enabled at hotplug time
PCI hotplug: shpchp: Removed check for hotplug of display devices
PCI hotplug: pciehp: Fixed return value sign for pciehp_unconfigure_device
PCI: Don't enable aspm before drivers have had a chance to veto it
...
Commit 69309a0590 ("x86, asm: Clean up and simplify set_64bit()")
sanitized the x86-64 types to set_64bit(), and incidentally resulted in
warnings like
drivers/pci/intr_remapping.c: In function 'modify_irte':
drivers/pci/intr_remapping.c:314: warning: passing argument 1 of 'set_64bit' from incompatible pointer type
arch/x86/include/asm/cmpxchg_64.h:6: note:expected 'volatile u64 *' but argument is of type 'long unsigned int *'
It turns out that the change to set_64bit() really does clean up things,
and the PCI intr_remapping.c file did a rather ugly cast in order to
avoid warnings with the previous set_64bit() type model.
Removing the ugly cast fixes the warning, and makes everybody happy and
expects a set_64bit() to take the logical "u64 *" argument.
Pointed-out-by: Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Export cache-coherency capability
iommu-api: Extension to check for interrupt remapping
x86/amd-iommu: Use for_each_pci_dev()
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_fsl,mv,nv: prepare for NCQ command completion update
ata: Convert pci_table entries to PCI_VDEVICE (if PCI_ANY_ID is used)
libata: more PCI IDs for jmicron controllers
ata_piix: fix locking around SIDPR access
[libata] update blacklist for new hyphenated pattern ranges (v2)
libata: allow hyphenated pattern ranges
ata_generic: drop hard coded DMA force logic for CENATEK
[libata] ahci: Fix warning: comparison between 'enum <anonymous>' and 'enum <anonymous>'
[libata] add ATA_CMD_DSM to ata_get_cmd_descript
[libata] Add Samsung PATA controller driver, pata_samsung_cf
[libata] Add 460EX on-chip SATA driver, sata_dwc_460ex
libata: reduce blacklist size even more (v2)
libata: reduce blacklist size (v2)
libata: glob_match for ata_device_blacklist (v2)
ahci_platform: Remove unneeded ahci_driver.probe assignment
ahci_platform: Provide for vendor specific init
On some platforms (MacPro3,1) the BIOS assigns the ioatdma device to the
incorrect iommu causing faults when the driver initializes. Add a quirk
to catch this misconfiguration and try falling back to untranslated
operation (which works in the MacPro3,1 case).
Assuming there are other platforms with misconfigured iommus teach the
ioatdma driver to treat initialization failures as non-fatal (just fail
the driver load and emit a warning instead of triggering a BUG_ON).
This can be classified as a boot regression since 2.6.32 on affected
platforms since the ioatdma module did not autoload prior to that
kernel.
Cc: <stable@kernel.org>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Reported-by: Chris Li <lkml@chrisli.org>
Tested-by: Chris Li <lkml@chrisli.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch fixes the below warnings introduced by the commit
911e1c9b05 ("PCI:
export SMBIOS provided firmware instance and label to sysfs").
drivers/pci/pci.h: In function ‘pci_create_firmware_label_files’:
drivers/pci/pci.h:16: warning: ‘return’ with a value, in function returning void
drivers/pci/pci.h: In function ‘pci_remove_firmware_label_files’:
drivers/pci/pci.h:18: warning: ‘return’ with a value, in function returning void
The warnings are seen because of the below code, doing a retun 0
from the functions 'pci_create_firmware_label_files' and
'pci_remove_firmware_label_files' defined as void.
+#ifndef CONFIG_DMI
+static inline void pci_create_firmware_label_files(struct pci_dev *pdev)
+{ return 0; }
+static inline void pci_remove_firmware_label_files(struct pci_dev *pdev)
+{ return 0; }
Signed-off-by: Narendra K <narendra_k@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add support for JMB364 and 369.
Patch-originally-from: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There is no reason to run NVidia-specific quirks related to HT MSI
mappings with MSI disabled via pci=nomsi, so make
__nv_msi_ht_cap_quirk() return immediately in that case.
This allows at least one machine to boot 100% of the time with
pci=nomsi (it still doesn't boot reliably without that).
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16443 .
Cc: stable@kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
commit 2ca1af9aa3285c6a5f103ed31ad09f7399fc65d7 "PCI: MSI: Remove
unsafe and unnecessary hardware access" changed read_msi_msg_desc() to
return the last MSI message written instead of reading it from the
device, since it may be called while the device is in a reduced
power state.
However, the pSeries platform code really does need to read messages
from the device, since they are initially written by firmware.
Therefore:
- Restore the previous behaviour of read_msi_msg_desc()
- Add new functions get_cached_msi_msg{,_desc}() which return the
last MSI message written
- Use the new functions where appropriate
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch exports SMBIOS provided firmware instance and label of
onboard PCI devices to sysfs. New files are:
/sys/bus/pci/devices/.../label which contains the firmware name for
the device in question, and
/sys/bus/pci/devices/.../index which contains the firmware device type
instance for the given device.
Signed-off-by: Jordan Hargrave <jordan_hargrave@dell.com>
Signed-off-by: Narendra K <narendra_k@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCI sysfs resource files currently only allow mmap'ing. On x86 this
works fine for memory backed BARs, but doesn't work at all for I/O
port backed BARs. Add read/write to I/O port PCI sysfs resource
files to allow userspace access to these device regions.
Acked-by: Chris Wright <chrisw@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In 2.6.34, we transformed the PCI DMA API into the generic device
mode. The PCI DMA API is just the wrapper of the DMA API.
So we don't need HAVE_ARCH_PCI_SET_DMA_MAX_SEGMENT_SIZE or
HAVE_ARCH_PCI_SET_DMA_SEGMENT_BOUNDARY (which enable architectures to
have the own implementations). Both haven't been used anyway.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It is a known issue that mmio decoding shall be disabled while doing PCI
bar sizing. Host bridge and other devices (PCI PIC) shall be excluded for
certain platforms. This patch mainly comes from Mathew Willcox's
patch in http://kerneltrap.org/mailarchive/linux-kernel/2007/9/13/258969.
A new flag bit "mmio_alway_on" is added to pci_dev with the intention that
devices with their mmio decoding cannot be disabled during BAR sizing shall
have this bit set, preferrablly in their quirks.
Without this patch, Intel Moorestown platform graphics unit will be
corrupted during bar sizing activities.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During suspend on an SMP system, {read,write}_msi_msg_desc() may be
called to mask and unmask interrupts on a device that is already in a
reduced power state. At this point memory-mapped registers including
MSI-X tables are not accessible, and config space may not be fully
functional either.
While a device is in a reduced power state its interrupts are
effectively masked and its MSI(-X) state will be restored when it is
brought back to D0. Therefore these functions can simply read and
write msi_desc::msg for devices not in D0.
Further, read_msi_msg_desc() should only ever be used to update a
previously written message, so it can always read msi_desc::msg
and never needs to touch the hardware.
Tested-by: "Michael Chan" <mchan@broadcom.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The CONFIG_PCIEASPM option is confusing and potentially dangerous. ASPM is
a hardware mediated feature rather than one under direct OS control, and
even if the config option is disabled the system firmware may have turned
on ASPM on various bits of hardware. This can cause problems later -
various hardware that claims to support ASPM does a poor job of it and may
hang or cause other difficulties. The kernel is able to recognise this in
many cases and disable the ASPM functionality, but only if CONFIG_PCIEASPM
is enabled.
Given that in its default configuration this option will either leave the
hardware as it was originally or disable hardware functionality that may
cause problems, it should by default y. The only reason to disable it
ought to be to reduce code size, so make it dependent on CONFIG_EMBEDDED.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: lrodriguez@atheros.com
Cc: maximlevitsky@gmail.com
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Found one PCIe Module with several bridges built-in where a "cold"
hotadd doesn't work.
If we end up reassigning bridge windows at hotadd time, and have to loop
through assigning new ranges, we won't end up enabling the child bridges
because the first assignment pass already tried to enable them, which
prevents __pci_bridge_assign_resource from updating the windows.
So try to move enabling of child bridges to the end, and only do it
once.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Removed check to prevent hotplug of display devices within shpchp.
Originally this was thought to have been required within the PCI
Hotplug specification for some legacy devices. However there is
no such requirement in the most recent revision. The check prevents
hotplug of not only display devices but also computational GPUs
which require serviceability.
Signed-off-by: Praveen Kalamegham <praveen@nextio.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The aspm code will currently set the configured aspm policy before drivers
have had an opportunity to indicate that their hardware doesn't support it.
Unfortunately, putting some hardware in L0 or L1 can result in the hardware
no longer responding to any requests, even after aspm is disabled. It makes
more sense to leave aspm policy at the BIOS defaults at initial setup time,
reconfiguring it after pci_enable_device() is called. This allows the
driver to blacklist individual devices beforehand.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use resource_size_t for MMIO address instead of unsigned long. Otherwise,
higher 32-bits of MMIO address are cleared unexpectedly in x86-32 PAE.
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_enable_device can fail. In that case, a printed warning would be
more appropriate.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Junchang Wang <junchangwang@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Assigning zero where NULL should be used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
MSI delivery from on-board ahci controller doesn't work on K8M800. At
this point, it's unclear whether the culprit is with the ahci
controller or the host bridge. Given the track record and considering
the rather minimal impact of MSI, disabling it seems reasonable.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Rainer Hurtado Navarro <publio.escipion.el.africano@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In all AMD 780 family northbridges, the vendor ID of the internal
graphics PCI/PCI bridge reads not as AMD but as that of the mainboard
vendor, because the hardware actually returns the value of the subsystem
vendor ID (erratum 18).
We currently have additional quirk entries for Asus and Acer, but it is
likely that we will encounter more systems with other vendor IDs.
Since we do not know in advance all possible vendor IDs, a better way to
find the device is to declare the quirk on the host bridge, whose ID is
always correct, and use that device as a stepping stone to find the PCI/
PCI bridge, if present.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The SLOT_REG_RSVDZ_MASK macro is normally used like this:
slot_reg &= ~SLOT_REG_RSVDZ_MASK;
The ~ operator has higher precedence than the | operator from inside the
macro, so it needs parenthesis.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some compiler generates following warnings:
In function 'aer_isr':
warning: 'e_src.id' may be used uninitialized in this function
warning: 'e_src.status' may be used uninitialized in this function
Avoid status flag "int ret" and return constants instead, so that
gcc sees the return value matching "it is initialized" better.
Acked-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch (as1388) changes the way the PCI core handles runtime PM
settings when probing or unbinding drivers. Now the core will make
sure the device is enabled for runtime PM, with a usage count >= 1,
when a driver is probed. It does the same when calling a driver's
remove method.
If the driver wants to use runtime PM, all it has to do is call
pm_runtime_pu_noidle() near the end of its probe routine (to cancel
the core's usage increment) and pm_runtime_get_noresume() near the
start of its remove routine (to restore the usage count). It does not
need to mess around with setting the runtime state to enabled,
disabled, active, or suspended.
The patch updates e1000e and r8169, the only PCI drivers that already
use the existing runtime PM interface.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch allows IOMMU users to determine whether the
hardware and software support safe, isolated interrupt
remapping. Not all Intel IOMMUs have the hardware, and the
software for AMD is not there yet.
Signed-off-by: Tom Lyon <pugs@cisco.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
One of the arguments during the suspend blockers discussion was that
the mainline kernel didn't contain any mechanisms making it possible
to avoid races between wakeup and system suspend.
Generally, there are two problems in that area. First, if a wakeup
event occurs exactly when /sys/power/state is being written to, it
may be delivered to user space right before the freezer kicks in, so
the user space consumer of the event may not be able to process it
before the system is suspended. Second, if a wakeup event occurs
after user space has been frozen, it is not generally guaranteed that
the ongoing transition of the system into a sleep state will be
aborted.
To address these issues introduce a new global sysfs attribute,
/sys/power/wakeup_count, associated with a running counter of wakeup
events and three helper functions, pm_stay_awake(), pm_relax(), and
pm_wakeup_event(), that may be used by kernel subsystems to control
the behavior of this attribute and to request the PM core to abort
system transitions into a sleep state already in progress.
The /sys/power/wakeup_count file may be read from or written to by
user space. Reads will always succeed (unless interrupted by a
signal) and return the current value of the wakeup events counter.
Writes, however, will only succeed if the written number is equal to
the current value of the wakeup events counter. If a write is
successful, it will cause the kernel to save the current value of the
wakeup events counter and to abort the subsequent system transition
into a sleep state if any wakeup events are reported after the write
has returned.
[The assumption is that before writing to /sys/power/state user space
will first read from /sys/power/wakeup_count. Next, user space
consumers of wakeup events will have a chance to acknowledge or
veto the upcoming system transition to a sleep state. Finally, if
the transition is allowed to proceed, /sys/power/wakeup_count will
be written to and if that succeeds, /sys/power/state will be written
to as well. Still, if any wakeup events are reported to the PM core
by kernel subsystems after that point, the transition will be
aborted.]
Additionally, put a wakeup events counter into struct dev_pm_info and
make these per-device wakeup event counters available via sysfs,
so that it's possible to check the activity of various wakeup event
sources within the kernel.
To illustrate how subsystems can use pm_wakeup_event(), make the
low-level PCI runtime PM wakeup-handling code use it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: markgross <markgross@thegnar.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
If we fail to assign resources to a PCI BAR, this patch makes us try the
original address from BIOS rather than leaving it disabled.
Linux tries to make sure all PCI device BARs are inside the upstream
PCI host bridge or P2P bridge apertures, reassigning BARs if necessary.
Windows does similar reassignment.
Before this patch, if we could not move a BAR into an aperture, we left
the resource unassigned, i.e., at address zero. Windows leaves such BARs
at the original BIOS addresses, and this patch makes Linux do the same.
This is a bit ugly because we disable the resource long before we try to
reassign it, so we have to keep track of the BIOS BAR address somewhere.
For lack of a better place, I put it in the struct pci_dev.
I think it would be cleaner to attempt the assignment immediately when the
claim fails, so we could easily remember the original address. But we
currently claim motherboard resources in the middle, after attempting to
claim PCI resources and before assigning new PCI resources, and changing
that is a fairly big job.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16263
Reported-by: Andrew <nitr0@seti.kr.ua>
Tested-by: Andrew <nitr0@seti.kr.ua>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After the previous patch that introduced acpi_gpe_wakeup() and
modified the ACPI suspend and wakeup code to use it, the third
argument of acpi_{enable|disable}_gpe() and the GPE wakeup
reference counter are not necessary any more. Remove them and
modify all of the users of acpi_{enable|disable}_gpe()
accordingly. Also drop GPE type constants that aren't used
any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
virtio-pci resets the device at startup by writing to the status
register, but this does not clear the pci config space,
specifically msi enable status which affects register
layout.
This breaks things like kdump when they try to use e.g. virtio-blk.
Fix by forcing msi off at startup. Since pci.c already has
a routine to do this, we export and use it instead of duplicating code.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Commit c7f486567c
(PCI PM: PCIe PME root port service driver) causes the native PCIe
PME signaling to be used by default, if the BIOS allows the kernel to
control the standard configuration registers of PCIe root ports.
However, the native PCIe PME is coupled to the native PCIe hotplug
and calling pcie_pme_acpi_setup() makes some BIOSes expect that
the native PCIe hotplug will be used as well. That, in turn, causes
problems to appear on systems where the PCIe hotplug driver is not
loaded. The usual symptom, as reported by Jaroslav Kameník and
others, is that the ACPI GPE associated with PCIe hotplug keeps
firing continuously causing kacpid to take substantial percentage
of CPU time.
To work around this issue, change the default so that the native
PCIe PME signaling is only used if directly requested with the help
of the pcie_pme= command line switch.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15924 , which is
a listed regression from 2.6.33.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Jaroslav Kameník <jaroslav@kamenik.cz>
Tested-by: Antoni Grzymala <antekgrzymala@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Certain revisions of this chipset appear to be broken. There is a shadow
GTT which mirrors the real GTT but contains pre-translated physical
addresses, for performance reasons. When a GTT update happens, the
translations are done once and the resulting physical addresses written
back to the shadow GTT.
Except sometimes, the physical address is actually written back to the
_real_ GTT, not the shadow GTT. Thus we start to see faults when that
physical address is fed through translation again.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
stanse found the following double lock.
In get_domain_for_dev:
spin_lock_irqsave(&device_domain_lock, flags);
domain_exit(domain);
domain_remove_dev_info(domain);
spin_lock_irqsave(&device_domain_lock, flags);
spin_unlock_irqrestore(&device_domain_lock, flags);
spin_unlock_irqrestore(&device_domain_lock, flags);
This happens when the domain is created by another CPU at the same time
as this function is creating one, and the other CPU wins the race to
attach it to the device in question, so we have to destroy our own
newly-created one.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit a99c47a2 "intel-iommu: errors with smaller iommu widths" replace the
dmar_domain->pgd with the first entry of page table when iommu's supported
width is smaller than dmar_domain's. But it use physical address directly
for new dmar_domain->pgd...
This result in KVM oops with VT-d on some machines.
Reported-by: Allen Kay <allen.m.kay@intel.com>
Cc: Tom Lyon <pugs@cisco.com>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: clear bridge resource range if BIOS assigned bad one
PCI: hotplug/cpqphp, fix NULL dereference
Revert "PCI: create function symlinks in /sys/bus/pci/slots/N/"
PCI: change resource collision messages from KERN_ERR to KERN_INFO
There are devices out there which are PCI Hot-plug controllers with
compaq PCI IDs, but are not bridges, hence have pdev->subordinate
NULL. But cpqphp expects the pointer to be non-NULL.
Add a check to the probe function to avoid oopses like:
BUG: unable to handle kernel NULL pointer dereference at 00000050
IP: [<f82e3c41>] cpqhpc_probe+0x951/0x1120 [cpqphp]
*pdpt = 0000000033779001 *pde = 0000000000000000
...
The device here was:
00:0b.0 PCI Hot-plug controller [0804]: Compaq Computer Corporation PCI Hotplug Controller [0e11:a0f7] (rev 11)
Subsystem: Compaq Computer Corporation Device [0e11:a2f8]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reverts commit 75568f8094.
Since they're just a convenience anyway, remove these symlinks since
they're causing duplicate filename errors in the wild.
Acked-by: Alex Chiang <achiang@canonical.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We can often deal with PCI resource issues by moving devices around. In
that case, there's no point in alarming the user with messages like these.
There are many bug reports where the message itself is the only problem,
e.g., https://bugs.launchpad.net/ubuntu/+source/linux/+bug/413419 .
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
JMB362 is a new variant of jmicron controller which is similar to
JMB360 but has two SATA ports instead of one. As there is no PATA
port, single function AHCI mode can be used as in JMB360. Add pci
quirk for JMB362.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Aries Lee <arieslee@jmicron.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.infradead.org/iommu-2.6:
intel-iommu: Set a more specific taint flag for invalid BIOS DMAR tables
intel-iommu: Combine the BIOS DMAR table warning messages
panic: Add taint flag TAINT_FIRMWARE_WORKAROUND ('I')
panic: Allow warnings to set different taint flags
intel-iommu: intel_iommu_map_range failed at very end of address space
intel-iommu: errors with smaller iommu widths
intel-iommu: Fix boot inside 64bit virtualbox with io-apic disabled
intel-iommu: use physfn to search drhd for VF
intel-iommu: Print out iommu seq_id
intel-iommu: Don't complain that ACPI_DMAR_SCOPE_TYPE_IOAPIC is not supported
intel-iommu: Avoid global flushes with caching mode.
intel-iommu: Use correct domain ID when caching mode is enabled
intel-iommu mistakenly uses offset_pfn when caching mode is enabled
intel-iommu: use for_each_set_bit()
intel-iommu: Fix section mismatch dmar_ir_support() uses dmar_tbl.
Removed check to prevent hotplug of display devices within pciehp.
Originally this was thought to have been required within the PCI
Hotplug specification for some legacy devices. However there is
no such requirement in the most recent revision. The check prevents
hotplug of not only display devices but also computational GPUs
which require serviceability.
Signed-off-by: Praveen Kalamegham <praveen@nextio.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
At the moment only PCI-E briges can be flagged as hotplug, thus
allowing manual resource preallocation via pci=hpmemsize=nnM and
pci=hpiosize=nnM kernel parameters. Some PCI hotplug bridges, e.g.
PLX 6254 can also benefit from this functionalily, as kernel fails
to properly allocate their resources when hotplug device is added
and PCI bus is rescanned.
This patch adds header quirk for PLX 6254 that marks this bridge
as hotplug. Other PCI bridges with similar problems can use it
as well.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCI config space bin_attr read handler has a hardcoded CAP_SYS_ADMIN
check to verify privileges before allowing a user to read device
dependent config space. This is meant to protect from an unprivileged
user potentially locking up the box.
When assigning a PCI device directly to a guest with libvirt and KVM,
the sysfs config space file is chown'd to the unprivileged user that
the KVM guest will run as. The guest needs to have full access to the
device's config space since it's responsible for driving the device.
However, despite being the owner of the sysfs file, the CAP_SYS_ADMIN
check will not allow read access beyond the config header.
With this patch we check privileges against the capabilities used when
openining the sysfs file. The allows a privileged process to open the
file and hand it to an unprivileged process, and the unprivileged process
can still read all of the config space.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
Now, a dedicated HEST tabling parsing code is used for PCIE AER
firmware_first setup. It is rebased on general HEST tabling parsing
code of APEI. The firmware_first setup code is moved from PCI core to
AER driver too, because it is only AER related.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
We now know how to deal with these tables so that they are harmless.
Set TAINT_FIRMWARE_WORKAROUND instead of the default TAINT_WARN.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We have nearly the same code for warnings repeated four times. Move
it into a separate function.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_read/write_vpd() can fail due to a timeout. Usually the command
times out because of firmware issues (incorrect vpd length, etc.) on the
PCI card. Currently, the timeout occurs silently.
Output a message to the user indicating that they should check with
their vendor for new firmware.
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This fixes all occurrences of pci_enable_device and pci_disable_device
in all comments. There are no code changes involved.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As reported in <http://bugs.debian.org/552299>, MSI appears to be
broken for this on-board device. We already have a quirk for the
P5N32-SLI Premium; extend it to cover both variants of the board.
Reported-by: Romain DEGEZ <romain.degez@smartjog.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Add amd_iommu=off command line option
iommu-api: Remove iommu_{un}map_range functions
x86/amd-iommu: Implement ->{un}map callbacks for iommu-api
x86/amd-iommu: Make amd_iommu_iova_to_phys aware of multiple page sizes
x86/amd-iommu: Make iommu_unmap_page and fetch_pte aware of page sizes
x86/amd-iommu: Make iommu_map_page and alloc_pte aware of page sizes
kvm: Change kvm_iommu_map_pages to map large pages
VT-d: Change {un}map_range functions to implement {un}map interface
iommu-api: Add ->{un}map callbacks to iommu_ops
iommu-api: Add iommu_map and iommu_unmap functions
iommu-api: Rename ->{un}map function pointers to ->{un}map_range
intel_iommu_map_range() doesn't allow allocation at the very end of the
address space; that code has been simplified and corrected.
Signed-off-by: Tom Lyon <pugs@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When using iommu_domain_alloc with the Intel iommu, the domain address
width is always initialized to 48 bits (agaw 2). This domain->agaw value
is then used by pfn_to_dma_pte to (always) build a 4 level page table.
However, not all systems support iommu width of 48 or 4 level page tables.
In particular, the Core i5-660 and i5-670 support an address width of 36
bits (not 39!), an agaw of only 1, and only 3 level page tables.
This version of the patch simply lops off extra levels of the page tables
if the agaw value of the iommu is less than what is currently allocated
for the domain (in intel_iommu_attach_device). If there were already
allocated addresses above what the new iommu can handle, EFAULT is
returned.
Signed-off-by: Tom Lyon <pugs@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This reverts commit 977d17bb17, because it
can cause problems with some devices not getting any resources at all
when the resource tree is re-allocated.
For an example of this, see
https://bugzilla.kernel.org/show_bug.cgi?id=15960
(originally https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4982)
(lkml thread: http://lkml.org/lkml/2010/4/19/20)
where Peter Henriksson reported his Xonar DX sound card gone, because
the IO port region was no longer allocated.
Reported-bisected-and-tested-by: Peter Henriksson <peter.henriksson@gmail.com>
Requested-by: Andrew Morton <akpm@linux-foundation.org>
Requested-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Skip zero-ing in aer_alloc_rpc() since it is allocated by kzalloc().
The closing comment marker "*/" is recommended for kernel-doc comments.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I noticed that when I inject a fatal error to an endpoint via
aer-inject, aer_root_reset() is called as reset_link for a
downstream port at upstream of the endpoint:
pcieport 0000:00:06.0: AER: Uncorrected (Fatal) error received: id=5401
:
pcieport 0000:52:02.0: Root Port link has been reset
It externally appears to be working, but internally issues some
accesses to PCI_ERR_ROOT_COMMAND/STATUS registers that is for
root port so not available on downstream port.
This patch introduces default_downstream_reset_link that is
a version of aer_root_reset() with no accesses to root port's
register. It is used for downstream ports that has no reset_link
function its specific.
This patch also updates related description in pcieaer-howto.txt.
Some minor fixes are included.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pcie->port of port service device points the port associated
the service with. The find_aer_service iterates over children of
given port udev.
So it is clear that the pcie->port of port service of given port
udev must always point the udev.
Therefore we can know the type of udev without checking its children.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Make it clear that we only interest in 2 *_RCV bits.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current get_e_source() returns pointer to an element of array.
However since it also progress consume counter, it is possible
that the element is overwritten by newly produced data before
the element is really consumed.
This patch changes get_e_source() to copy contents of the element
to address pointed by its caller. Once copied the element in
array can be consumed.
And relocate this function to more innocuous place.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Divide tricky for-loop into readable if-blocks.
The logic to set multi_error_valid (to force walking pci bus
hierarchy to find 2nd~ error devices) is changed too, to check
MULTI_{,_UN}COR_RCV bit individually and to force walk only when
it is required.
And rework setting e_info->severity for uncorrectable, not to use
magic numbers.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stop iteration if we cannot register any more.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Take core part of find_device_iter() to make a new function
is_error_source() that checks given device has report an error
or not.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Return bool to indicate that the source device is found or not.
This allows us to skip calling aer_process_err_devices() if we can.
And move dev_printk for debug into this function.
v2: return bool instead of int
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These functions are only called from init/remove path of aerdrv,
so move them from aerdrv_core.c to aerdrv.c, to make them static.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This cleanup solves some minor naming issues by removing unuseful
function aer_delete_rootport() and by renaming disable_root_aer()
to aer_disable_rootport().
- Inconsistent location of alloc & free:
The struct rpc is allocated in aer_alloc_rpc() at aerdrv.c
while it is implicitly freed in aer_delete_rootport() at
aerdrv_core.c.
- Inconsistent function name:
It makes a bit confusion that aer_delete_rootport() is seemed
to be paired with aer_enable_rootport(), i.e. there is neither
"add" against "delete" nor "disable" against "enable".
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A successful write() to the "reset" sysfs attribute should return the
number of bytes written, not 0. Otherwise userspace (bash) retries the
write over and over again.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Most current machines have no problem with this, and in fact many devices and
features work best (or only!) with MSI.
Reported-by: Petteri Räty <betelgeuse@gentoo.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_lock must be a real spinlock in preempt-rt. Convert it to
raw_spinlock. No change for !RT kernels.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch (as1353) removes a couple of unnecessary assignments from
the PCI core. The should_wakeup flag is naturally initialized to 0;
there's no need to clear it.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Create convenience symlinks in sysfs, linking slots to device
functions, and vice versa. These links make it easier for users to
figure out which devices actually live in what slots.
For example:
sapphire:/sys/bus/pci/slots # ls
1 10 2 3 4 5 6 7 8 9
sapphire:/sys/bus/pci/slots # ls -l 3
total 0
-r--r--r-- 1 root root 65536 Aug 18 14:10 address
lrwxrwxrwx 1 root root 0 Aug 18 14:10 function0 ->
../../../../devices/pci0000:23/0000:23:01.0
lrwxrwxrwx 1 root root 0 Aug 18 14:10 function1 ->
../../../../devices/pci0000:23/0000:23:01.1
sapphire:/sys/bus/pci/slots # ls -l 3/function0/slot
lrwxrwxrwx 1 root root 0 Aug 18 14:13 3/function0/slot ->
../../../bus/pci/slots/3
The original form of this patch was written by Matthew Wilcox,
and was enhanced to include links from the sysfs slots/ directory
pointing back at the device functions.
Cc: willy@linux.intel.com
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Rafael J. Wysocki