Intel Lynxpoint PCH Low Power Subsystem has two general purpose SPI
controllers that are LPSS_SSP compatible. These controllers are enumerated
from ACPI namespace with ACPI IDs INT33C0 and INT33C1.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Intel LPSS SPI is pretty much the same as the PXA27xx SPI except that it
has few additional features over the original:
o FIFO depth is 256 entries
o RX FIFO has one watermark
o TX FIFO has two watermarks, low and high
o chip select can be controlled by writing to a register
The new FIFO registers follow immediately the PXA27xx registers but then there
are some additional LPSS private registers at offset 1k or 2k from the base
address. For these private registers we add new accessors that take advantage
of drv_data->lpss_base once it is resolved.
We add a new type LPSS_SSP that can be used to distinguish the LPSS devices
from others.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is useful when testing the functionality of the controller from userspace
and there aren't any real SPI slave devices connected to the bus.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Drivers should put the device into low power states proactively whenever the
device is not in use. Thus implement support for runtime PM and use the
autosuspend feature to make sure that we can still perform well in case we see
lots of SPI traffic within short period of time.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To be able to use DMA with this driver on non-PXA platforms we implement
support for the generic DMA engine API. This lets user to use different DMA
engines with little or no modification to the driver.
Request lines and channel numbers can be passed to the driver from the
platform specific data.
The DMA engine implementation will be selected by default even on PXA
platform. User can select the legacy DMA API by enabling Kconfig option
CONFIG_SPI_PXA2XX_PXADMA.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PXA SPI driver uses PXA platform specific private DMA implementation
which does not work on non-PXA platforms. In order to use this driver on
other platforms we break out the private DMA implementation into a separate
file that gets compiled only when CONFIG_SPI_PXA2XX_PXADMA is set. The DMA
functions are stubbed out if there is no DMA implementation selected (i.e
we are building on non-PXA platform).
While we are there we can kill the dummy DMA bits in pxa2xx_spi.h as they
are not needed anymore for CE4100.
Once this is done we can add the generic DMA engine support to the driver
that allows usage of any DMA controller that implements DMA engine API.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert clk_enable() to clk_prepare_enable() and clk_disable() to
clk_disable_unprepare() respectively in order to support the common clk
framework. Otherwise we get warnings on the console as the clock is not
prepared before it is enabled.
In addition we must cache the maximum clock rate to drv_data->max_clk_rate
at probe time because clk_get_rate() cannot be called in tasklet context.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SPI core provides infrastructure for standard message queueing so use
that instead of handling everything in the driver. This simplifies the
driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix following warnings seen when compiling 64-bit:
drivers/spi/spi-pxa2xx.c: In function ‘map_dma_buffers’: drivers/spi/spi-pxa2xx.c:384:7: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:384:40: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c: In function ‘pxa2xx_spi_probe’:
drivers/spi/spi-pxa2xx.c:1572:34: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:1572:34: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:1572:34: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:1572:27: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The spi-pxa2xx-pci glue driver had to implement pxa_ssp_request()/free() in
order to support the spi-pxa2xx platform driver. Since the ACPI enabled
platforms can use the same platform driver we would need to implement
pxa_ssp_request()/free() in some central place that can be shared by the
ACPI and PCI glue code.
Instead of doing that we can make pxa_ssp_request()/free() to be available
only when CONFIG_ARCH_PXA is set. On other arches these are being stubbed
out in preference to passing the ssp_device from the platform data
directly.
We also change the SPI bus number to be taken from ssp->port_id instead of
platform device id. This way the supporting code that passes the ssp can
decide the number (or it can set it to the same as pdev->id).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Bill Pemberton has done most of the legwork on this series. I've used
his script to purge the attributes from the drivers/gpio tree.
Reported-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Sort the SPI makefile and enforce the naming convention spi_*.c for
spi drivers.
This change also rolls the contents of atmel_spi.h into the .c file
since there is only one user of that particular include file.
v2: - Use 'spi-' prefix instead of 'spi_' to match what seems to be
be the predominant pattern for subsystem prefixes.
- Clean up filenames in Kconfig and header comment blocks
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Mika Westerberg