This includes trace points for:
kvm_arch_setup_guest_debug
kvm_arch_clear_guest_debug
I've also added some generic register setting trace events and also a
trace point to dump the array of hardware registers.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Finally advertise the KVM capability for SET_GUEST_DEBUG. Once arm
support is added this check can be moved to the common
kvm_vm_ioctl_check_extension() code.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This adds support for userspace to control the HW debug registers for
guest debug. In the debug ioctl we copy an IMPDEF registers into a new
register set called host_debug_state.
We use the recently introduced vcpu parameter debug_ptr to select which
register set is copied into the real registers when world switch occurs.
I've made some helper functions from hw_breakpoint.c more widely
available for re-use.
As with single step we need to tweak the guest registers to enable the
exceptions so we need to save and restore those bits.
Two new capabilities have been added to the KVM_EXTENSION ioctl to allow
userspace to query the number of hardware break and watch points
available on the host hardware.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This introduces a level of indirection for the debug registers. Instead
of using the sys_regs[] directly we store registers in a structure in
the vcpu. The new kvm_arm_reset_debug_ptr() sets the debug ptr to the
guest context.
Because we no longer give the sys_regs offset for the sys_reg_desc->reg
field, but instead the index into a debug-specific struct we need to
add a number of additional trap functions for each register. Also as the
generic generic user-space access code no longer works we have
introduced a new pair of function pointers to the sys_reg_desc structure
to override the generic code when needed.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This is a pre-cursor to sharing the code with the guest debug support.
This replaces the big macro that fishes data out of a fixed location
with a more general helper macro to restore a set of debug registers. It
uses macro substitution so it can be re-used for debug control and value
registers. It does however rely on the debug registers being 64 bit
aligned (as they happen to be in the hyp ABI).
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This adds support for single-stepping the guest. To do this we need to
manipulate the guests PSTATE.SS and MDSCR_EL1.SS bits to trigger
stepping. We take care to preserve MDSCR_EL1 and trap access to it to
ensure we don't affect the apparent state of the guest.
As we have to enable trapping of all software debug exceptions we
suppress the ability of the guest to single-step itself. If we didn't we
would have to deal with the exception arriving while the guest was in
kernelspace when the guest is expecting to single-step userspace. This
is something we don't want to unwind in the kernel. Once the host is no
longer debugging the guest its ability to single-step userspace is
restored.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This adds support for SW breakpoints inserted by userspace.
We do this by trapping all guest software debug exceptions to the
hypervisor (MDCR_EL2.TDE). The exit handler sets an exit reason of
KVM_EXIT_DEBUG with the kvm_debug_exit_arch structure holding the
exception syndrome information.
It will be up to userspace to extract the PC (via GET_ONE_REG) and
determine if the debug event was for a breakpoint it inserted. If not
userspace will need to re-inject the correct exception restart the
hypervisor to deliver the debug exception to the guest.
Any other guest software debug exception (e.g. single step or HW
assisted breakpoints) will cause an error and the VM to be killed. This
is addressed by later patches which add support for the other debug
types.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This is a precursor for later patches which will need to do more to
setup debug state before entering the hyp.S switch code. The existing
functionality for setting mdcr_el2 has been moved out of hyp.S and now
uses the value kept in vcpu->arch.mdcr_el2.
As the assembler used to previously mask and preserve MDCR_EL2.HPMN I've
had to add a mechanism to save the value of mdcr_el2 as a per-cpu
variable during the initialisation code. The kernel never sets this
number so we are assuming the bootcode has set up the correct value
here.
This also moves the conditional setting of the TDA bit from the hyp code
into the C code which is currently used for the lazy debug register
context switch code.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This commit adds a stub function to support the KVM_SET_GUEST_DEBUG
ioctl. Any unsupported flag will return -EINVAL. For now, only
KVM_GUESTDBG_ENABLE is supported, although it won't have any effects.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This commit defines the API headers for guest debugging. There are two
architecture specific debug structures:
- kvm_guest_debug_arch, allows us to pass in HW debug registers
- kvm_debug_exit_arch, signals exception and possible faulting address
The type of debugging being used is controlled by the architecture
specific control bits of the kvm_guest_debug->control flags in the ioctl
structure.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Bring into line with the comments for the other structures and their
KVM_EXIT_* cases. Also update api.txt to reflect use in kvm_run
documentation.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
With the actual code, if a memory allocation error happens while
refilling a Rx descriptor, then the original Rx buffer is both passed
to the networking stack (in a SKB) and let in the Rx ring. This leads
to various kernel oops and crashes.
As a fix, this patch moves Rx descriptor refilling ahead of building
SKB with the associated Rx buffer. In case of a memory allocation
failure, data is dropped and the original DMA buffer is put back into
the Rx ring.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Cc: <stable@vger.kernel.org> # v3.8+
Tested-by: Yoann Sculo <yoann@sculo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 803f8fc462 ("stmmac: move driver data setting into
stmmac_dvr_probe") mistakenly set priv and not priv->dev as
driver data. This meant that the remove, resume and suspend
callbacks that fetched and tried to use this data would most
likely explode. Fix the issue by using the correct variable.
Fixes: 803f8fc462 ("stmmac: move driver data setting into stmmac_dvr_probe")
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following test case causes a NULL pointer dereference in cls_flow:
tc filter add dev foo parent 1: handle 0x1 flow hash keys dst action ok
tc filter replace dev foo parent 1: pref 49152 handle 0x1 \
flow hash keys mark action drop
To be more precise, actually two different panics are fixed, the first
occurs because tcf_exts_init() is not called on the newly allocated
filter when we do a replace. And the second panic uncovered after that
happens since the arguments of list_replace_rcu() are swapped, the old
element needs to be the first argument and the new element the second.
Fixes: 70da9f0bf9 ("net: sched: cls_flow use RCU")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following test case causes a NULL pointer dereference in cls_flower:
tc filter add dev foo parent 1: flower eth_type ipv4 action ok flowid 1:1
tc filter replace dev foo parent 1: pref 49152 handle 0x1 \
flower eth_type ipv6 action ok flowid 1:1
The problem is that commit 77b9900ef5 ("tc: introduce Flower classifier")
accidentally swapped the arguments of list_replace_rcu(), the old
element needs to be the first argument and the new element the second.
Fixes: 77b9900ef5 ("tc: introduce Flower classifier")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following test case causes a NULL pointer dereference in cls_bpf:
FOO="1,6 0 0 4294967295,"
tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 action ok
tc filter replace dev foo parent 1: pref 49152 handle 0x1 \
bpf bytecode "$FOO" flowid 1:1 action drop
The problem is that commit 1f947bf151 ("net: sched: rcu'ify cls_bpf")
accidentally swapped the arguments of list_replace_rcu(), the old
element needs to be the first argument and the new element the second.
Fixes: 1f947bf151 ("net: sched: rcu'ify cls_bpf")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Arik introduced an rtnl-locked regulatory API to be able
to differentiate between place do/don't have the RTNL;
this fixes missing locking in some of the code paths
2. Two small mesh bugfixes from Bob, one to avoid treating
a certain malformed over-the-air frame and one to avoid
sending a garbage field over the air.
3. A fix for powersave during WoWLAN suspend from Krishna Chaitanya.
4. A fix for a powersave vs. aggregation teardown race, from Michal.
5. Thomas reduced the loglevel of CRDA messages to avoid spamming
the kernel log with mostly irrelevant information.
6. Tom fixed a dangling debugfs directory pointer that could cause
crashes if subsequent addition of the same interface to debugfs
failed for some reason.
7. A fix from myself for a list corruption issue in mac80211 during
combined interface shutdown/removal - shut down interfaces first
and only then remove them to avoid that.
-----BEGIN PGP SIGNATURE-----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=US5Y
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-07-17' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Some fixes for the current cycle:
1. Arik introduced an rtnl-locked regulatory API to be able
to differentiate between place do/don't have the RTNL;
this fixes missing locking in some of the code paths
2. Two small mesh bugfixes from Bob, one to avoid treating
a certain malformed over-the-air frame and one to avoid
sending a garbage field over the air.
3. A fix for powersave during WoWLAN suspend from Krishna Chaitanya.
4. A fix for a powersave vs. aggregation teardown race, from Michal.
5. Thomas reduced the loglevel of CRDA messages to avoid spamming
the kernel log with mostly irrelevant information.
6. Tom fixed a dangling debugfs directory pointer that could cause
crashes if subsequent addition of the same interface to debugfs
failed for some reason.
7. A fix from myself for a list corruption issue in mac80211 during
combined interface shutdown/removal - shut down interfaces first
and only then remove them to avoid that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We store c45 PHY's id information in c45_ids, so it should be used to
check the matching between PHY driver and PHY device for c45 PHY.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel generates a lot of warnings when dst entry reference counter
overflows and becomes negative. That bug was seen several times at
machines with outdated 3.10.y kernels. Most like it's already fixed
in upstream. Anyway that flood completely kills machine and makes
further debugging impossible.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) If sk_filter() is applied, skb was leaked (not freed)
2) Testing SOCK_DEAD twice is racy :
packet could be freed while already queued.
3) Remove obsolete comment about caching skb->len
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sierra Wireless MC7305/MC7355 with USB ID 1199:9041 also provide a
second QMI/network interface like the MC73xx with USB ID 1199:68c0 on
USB interface #10 when used in the appropriate USB configuration.
Add the corresponding QMI_FIXED_INTF entry to the qmi_wwan driver.
Please note that the second QMI/network interface is not working for
early MC73xx firmware versions like 01.08.x as the device does not
respond to QMI messages on the second /dev/cdc-wdm port.
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TCCR.TSRQn bit may get clearead after TCCR gets read, so that TCCR write
would get skipped. We don't need to check this bit before setting.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The keystone qmss will raise interrupt when packet arrive at the
receive queue. Only control available to avoid interrupt from happening
is to keep the free descriptor queue (FDQ) empty in the receive side.
So the filling of descriptors into the FDQ has to happen after
request_irq() call is made as part of knav_queue_enable_notify(). So
move the function netcp_rxpool_refill() after this call.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "follow" fail_over_mac policy is useful for multiport devices that
either become confused or incur a performance penalty when multiple
ports are programmed with the same MAC address, but the same MAC
address still may happened by this steps for this policy:
1) echo +eth0 > /sys/class/net/bond0/bonding/slaves
bond0 has the same mac address with eth0, it is MAC1.
2) echo +eth1 > /sys/class/net/bond0/bonding/slaves
eth1 is backup, eth1 has MAC2.
3) ifconfig eth0 down
eth1 became active slave, bond will swap MAC for eth0 and eth1,
so eth1 has MAC1, and eth0 has MAC2.
4) ifconfig eth1 down
there is no active slave, and eth1 still has MAC1, eth2 has MAC2.
5) ifconfig eth0 up
the eth0 became active slave again, the bond set eth0 to MAC1.
Something wrong here, then if you set eth1 up, the eth0 and eth1 will have the same
MAC address, it will break this policy for ACTIVE_BACKUP mode.
This patch will fix this problem by finding the old active slave and
swap them MAC address before change active slave.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJVp19MAAoJEP5prqPJtc/HsA8IAIqYKwJtXHItVoG6GBxLo/iJ
G6OhCxSgDPUdytdyvWRmYL+2g6q9+BefnApwGroM0wowytHx4I6kF2O4LKEvthnD
TzDV6uY0n1CR8FzCdfQdTFedAfxIx7DLCqY/iC+JRFTh6Vhvj46WtHickthu4Se+
ygTWg5f5Da086JTUtwbb75TCHJv8xxtN57t6yZTtDoyaftqWd1Dzrmi8dBwHRWBA
6X/rE4VekFwFCbqOlv5ghm86lD77sMTEaU0xkm9FeZmO/CnUD3JASwi844RtCqXR
wj3OJ89qH14YmpJwjpakIwHfTyyPJurzPpPkCTZ6awmdNhCvp+h3nbfjKRqs0WU=
=pQGs
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.2-20150716' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-07-16
this is a pull request of 2 patches by Stefan Agner. He fixes the resume
operation in the mcp251x driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts 19424e052f ("sit:
Add gro callbacks to sit_offload") because it generates packets
that cannot be handled even by our own GSO.
Reported-by: Wolfgang Walter <linux@stwm.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
7445E0 contains an ECO which disconnected the internal SF2 pseudo-PHY which was
known to conflict with the external pseudo-PHY of BCM53125 switches. This
motivated the need to utilize the internal SF2 MDIO controller via indirect
register reads/writes to control external Broadcom switches due to this address
conflict (both responded at address 30d).
For 7445E0, the internal pseudo-PHY of the SF2 switch got disconnected, and as
a consequence this prevents the internal SF2 MDIO bus controller from reading
data (reads back everything as 0) since the MDI line is tied low.
Fix this by making the indirect register reads and writes conditional to
7445D0, on 7445E0 we can utilize the SWITCH_MDIO controller (backed by
mdio-unimac and not the DSA created slave MII bus).
We utilize of_machine_is_compatible() here since this is the only way for use
to differentiate between these two chips in a way that does not violate layers
or becomes (too) vendor-specific.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the bond is enslaving a device with different type it will be setup
by it, but if after being setup the enslave fails the bond doesn't
switch back its type and also keeps pointers to foreign structures that can
be long gone. Thus revert back any type changes if the enslave failed and
the bond had to change its type.
Example:
Before patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default
link/loopback 16:54:78:34:bd:41 brd 00:00:00:00:00:00
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
(notice the MASTER flag is gone)
After patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
link/ether 6e:66:94:f6:07:fc brd ff:ff:ff:ff:ff:ff
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: e36b9d16c6 ("bonding: clean muticast addresses when device changes type")
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bonding is being unloaded and the netdevice notifier is
unregistered it executes NETDEV_UNREGISTER for each device which should
remove the bond's proc entry but if the device enslaved is not of
ARPHRD_ETHER type and is in front of the bonding, it may execute
bond_release_and_destroy() first which would release the last slave and
destroy the bond device leaving the proc entry and thus we will get the
following error (with dynamic debug on for bond_netdev_event to see the
events order):
[ 908.963051] eql: event: 9
[ 908.963052] eql: IFF_SLAVE
[ 908.963054] eql: event: 2
[ 908.963056] eql: IFF_SLAVE
[ 908.963058] eql: event: 6
[ 908.963059] eql: IFF_SLAVE
[ 908.963110] bond0: Releasing active interface eql
[ 908.976168] bond0: Destroying bond bond0
[ 908.976266] bond0 (unregistering): Released all slaves
[ 908.984097] ------------[ cut here ]------------
[ 908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575
remove_proc_entry+0x112/0x160()
[ 908.984110] remove_proc_entry: removing non-empty directory
'net/bonding', leaking at least 'bond0'
[ 908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss
oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul
crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper
snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw
gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec
psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev
drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core
pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button
autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom
ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci
virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore
usb_common [last unloaded: bonding]
[ 908.984168] CPU: 0 PID: 1787 Comm: rmmod Tainted: G W O
4.2.0-rc2+ #8
[ 908.984170] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 908.984172] 0000000000000000 ffffffff81732d41 ffffffff81525b34
ffff8800358dfda8
[ 908.984175] ffffffff8106c521 ffff88003595af78 ffff88003595af40
ffff88003e3a4280
[ 908.984178] ffffffffa058d040 0000000000000000 ffffffff8106c59a
ffffffff8172ebd0
[ 908.984181] Call Trace:
[ 908.984188] [<ffffffff81525b34>] ? dump_stack+0x40/0x50
[ 908.984193] [<ffffffff8106c521>] ? warn_slowpath_common+0x81/0xb0
[ 908.984196] [<ffffffff8106c59a>] ? warn_slowpath_fmt+0x4a/0x50
[ 908.984199] [<ffffffff81218352>] ? remove_proc_entry+0x112/0x160
[ 908.984205] [<ffffffffa05850e6>] ? bond_destroy_proc_dir+0x26/0x30
[bonding]
[ 908.984208] [<ffffffffa057540e>] ? bond_net_exit+0x8e/0xa0 [bonding]
[ 908.984217] [<ffffffff8142f407>] ? ops_exit_list.isra.4+0x37/0x70
[ 908.984225] [<ffffffff8142f52d>] ?
unregister_pernet_operations+0x8d/0xd0
[ 908.984228] [<ffffffff8142f58d>] ?
unregister_pernet_subsys+0x1d/0x30
[ 908.984232] [<ffffffffa0585269>] ? bonding_exit+0x23/0xdba [bonding]
[ 908.984236] [<ffffffff810e28ba>] ? SyS_delete_module+0x18a/0x250
[ 908.984241] [<ffffffff81086f99>] ? task_work_run+0x89/0xc0
[ 908.984244] [<ffffffff8152b732>] ?
entry_SYSCALL_64_fastpath+0x16/0x75
[ 908.984247] ---[ end trace 7c006ed4abbef24b ]---
Thus remove the proc entry manually if bond_release_and_destroy() is
used. Because of the checks in bond_remove_proc_entry() it's not a
problem for a bond device to change namespaces (the bug fixed by the
Fixes commit) but since commit
f939981492 ("bonding: Don't allow bond devices to change network
namespaces.") that can't happen anyway.
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: a64d49c3dd ("bonding: Manage /proc/net/bonding/ entries from
the netdev events")
Tested-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_priv_state structure contains an fid_mask, where 1 means
the FID is free to use, 0 means the FID is in use.
This patch fixes the bit clear in mv88e6xxx_leave_bridge() when
assigning a new FID to a port.
Example scenario: I have 7 ports, port 5 is CPU, port 6 is unused (no
PHY). After setting the ports 0, 1 and 2 in bridge br0, and ports 3 and
4 in bridge br1, I have the following fid_mask: 0b111110010110 (0xf96).
Indeed, br0 uses FID 0, and br1 uses FID 3.
After setting nomaster for port 0, I get the wrong fid_mask: 0b10 (0x2).
With this patch we correctly get 0b111110010100 (0xf94), meaning port 0
uses FID 1, br0 uses FID 0, and br1 uses FID 3.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ANY_LAYOUT is a compatibility feature. It's implied
for VERSION_1 devices, and non-transitional devices
might not offer it. Change code to behave accordingly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 fix from Martin Schwidefsky:
"Fast path fix for the thread_struct breakage"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: adapt entry.S to the move of thread_struct
Pull AVR32 update from Hans-Christian Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
AVR32/time: Migrate to new 'set-state' interface
git commit 0c8c0f03e3
"x86/fpu, sched: Dynamically allocate 'struct fpu'"
moved the thread_struct to the end of the task_struct.
This causes some of the offsets used in entry.S to overflow their
instruction operand field. To fix this use aghi to create a
dedicated pointer for the thread_struct.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Migrate avr32 driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
We want to call cpu_idle_poll_ctrl() in shutdown only if we were in
oneshot or resume state earlier. Create another variable to save this
information and check that in shutdown callback.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
The param_val variable is what determines if schmitt
trigger is enabled on a pin or not. A typo here mean
that schmitt trigger was always enabled for standard
and i2c pins.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
imx1_pinconf_set assumes that the array of pins in struct
imx1_pinctrl_soc_info can be indexed by pin id to get the
pinctrl_pin_desc for a pin. This used to be correct up to commit
607af165c0 which removed some entries from the array and so made it
wrong to access the array by pin id.
The result of this bug is a wrong pin name in the output for small pin
ids and an oops for the bigger ones.
This patch is the result of a discussion that includes patches by Markus
Pargmann and Chris Ruehl.
Fixes: 607af165c0 ("pinctrl: i.MX27: Remove nonexistent pad definitions")
Cc: stable@vger.kernel.org
Reported-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's possible to hit a race condition if interrupts are generated on a GPIO
pin when the IRQ line in question is being disabled.
If the interrupt is freed, bcm2835_gpio_irq_disable() is called which
disables the event generation sources (edge, level). If an event occurred
between the last disabling of hard IRQs and the write to the event
source registers, a bit would be set in the GPIO event detect register
(GPEDSn) which goes unacknowledged by bcm2835_gpio_irq_handler()
so Linux complains loudly.
There is no per-GPIO mask register, so when disabling GPIO interrupts
write 1 to the relevant bit in GPEDSn to clear out any stale events.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PFC driver causes the kernel to hang on the R-Car gen2 SoC based boards
when the CPU_ALL_PORT() macro is fixed to reflect the reality, i.e. when the
GPIO space becomes actually sparse. This happens because the _GP_GPIO() macro
includes an indexed initializer which causes the "holes" (array entries filled
with all 0s) between the groups of the existing GPIOs; and the driver can't
cope with that. There seems to be no reason to use the indexed initializer,
so we can remove the index specifier and so avoid the "holes".
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit a21763a0b1
"pinctrl: nomadik: activate strict mux mode"
put all Nomadik pin controllers to strict mode. This was
not good on the Snowball platform: the muxing of GPIOs to
different pins is done with hogs in the DTS file, and then
these GPIOs are used by offset, relying on hogs to mux the
pins. Since that means the pin controller "owns" the pins
and at the same time we have a GPIO user, this pin controller
is by definition not strict.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Two fairly simple fixes: one is a change that causes us to have a very low
queue depth leading to performance issues and the other is a null deref
occasionally in tapes thanks to use after put.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVq2/DAAoJEDeqqVYsXL0MhqoH/2ZlycWVQ2ZQyC9k2UWjAS7t
By0ufRZKeaxgwriVWZqTCE3QHfqqeR5tNNSvk26k+CJTS6nyVGX+g8cxLQJf1gey
DyAi9za+5P5SwYFuJxzULyZddTyeshoZplVvRwjd1/gnRUJXybuO+HRkYzaROd5e
7snX56jGt1MzpmIrO2wln24pFLVfdC5JivzUcXgYecHD/XZuzOEdZE1dCxONXy27
rTeqYayIGLFo7vhSt9J9ViF0QiU6ahCKmQ/TDsv3Sq1zg228E7DAmlzVAo2NCwLM
gelTRHRdO4rwwkehZH8QIdUI77MzgmwQIU4nZp3FBG9SWrIEPHaRpiDxCHr3UE0=
=bfE2
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fairly simple fixes: one is a change that causes us to have a very
low queue depth leading to performance issues and the other is a null
deref occasionally in tapes thanks to use after put"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fix host max depth checking for the 'queue_depth' sysfs interface
st: null pointer dereference panic caused by use after kref_put by st_open
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.2.
Things are looking quite decent at this stage but the recent work on
the FPU support took its toll:
- fix an incorrect overly restrictive ifdef
- select O32 64-bit FP support for O32 binary compatibility
- remove workarounds for Sibyte SB1250 Pass1 parts. There are rare
fixing the workarounds is not worth the effort.
- patch up an outdated and now incorrect comment"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: fpu.h: Allow 64-bit FPU on a 64-bit MIPS R6 CPU
MIPS: SB1: Remove support for Pass 1 parts.
MIPS: Require O32 FP64 support for MIPS64 with O32 compat
MIPS: asm-offset.c: Patch up various comments refering to the old filename.
Pull parisc fix from Helge Deller:
"A memory leak fix from Christophe Jaillet which was introduced with
kernel 4.0 and which leads to kernel crashes on parisc after 1-3 days"
* 'parisc-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: mm: Fix a memory leak related to pmd not attached to the pgd
By far most of the fixes here are updates to DTS files to deal with some
mostly minor bugs.
There's also a fix to deal with non-PM kernel configs on i.MX, a
regression fix for ethernet on PXA platforms and a dependency fix for OMAP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVqyQoAAoJEIwa5zzehBx3e6EQAIUcOpKzHZ9oC6r16Cs+UwRy
cFQcYwhZqR4XhlbkI5VBOY+Ul1Kd7GoRYkH1sSN0OLIO0ippO7gwzkioAnAoeFC9
lqdHLJ/tpwahJOdpSe8doFLrJ5uGybPccoAF5vxAWOxQbV21Ck7pzWxUpHsR0pAq
8nRvz8GmM4vXQih6hnFG9pXNLhY+jSYgabE0IPR0Eb2tRknsGWcvuYH5v+X9O563
7iNjQcBLHxd/otmbtN5p3Za8SmLDo0/iwBkXlruUXdAaotagTASwfmhjFTuqXOns
Pq9v+OUy2Ls06tyo/RDrS/WZOh81YV6az7Bk+ffAkHJzzg2nxs899dti7lBeo5D8
srhA6D7gpdZcJ87fXbubIhuQrMwsIwbMEjH1O4GR8DG0jcvGB4xCutGdTnKNpaFM
i697p8JpSCr43AcPcSGcXfi67fHIRuWFe/o+EnVbmOjUhiQ7+hnOzDMh5L/0Rg1A
+NntzHtyt6QSrPLFUkqA+zCnm/t6JIuvNRVzcn5cvBJPmFBxjDqBbe71CR7ipGcc
iaGSwLWoCKSi0cD9qCAiEjaB4Zxyea9Aif9uCjq40kDV2q+YFGNi1wjZKFS0etVu
NXrEaYa373pCEbr/A5ImI5LL8JOmG8VmXc+RteKEVzc9C4PpY1coDsOKO6Pvx7yO
XnW0naVnNOmdhzyas16B
=SOgd
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"By far most of the fixes here are updates to DTS files to deal with
some mostly minor bugs.
There's also a fix to deal with non-PM kernel configs on i.MX, a
regression fix for ethernet on PXA platforms and a dependency fix for
OMAP"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: dts: rename pcie nodes to help override status
ARM: keystone: dts: fix dt bindings for PCIe
ARM: pxa: fix dm9000 platform data regression
ARM: dts: Correct audio input route & set mic bias for am335x-pepper
ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX
MAINTAINERS: digicolor: add dts files
ARM: ux500: fix MMC/SD card regression
ARM: ux500: define serial port aliases
ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs
ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs
ARM: dts: Fix frequency scaling on Gumstix Pepper
ARM: dts: configure regulators for Gumstix Pepper
ARM: dts: omap3: overo: Update LCD panel names
ARM: dts: cros-ec-keyboard: Add support for some Japanese keys
ARM: imx6: gpc: always enable PU domain if CONFIG_PM is not set
ARM: dts: imx53-qsb: fix TVE entry
ARM: dts: mx23: fix iio-hwmon support
ARM: dts: imx27: Adjust the GPT compatible string
ARM: socfpga: dts: Fix entries order
ARM: socfpga: dts: Fix adxl34x formating and compatible string
Commit 6134d94923 ("MIPS: asm: fpu: Allow 64-bit FPU on MIPS32 R6")
added support for 64-bit FPU on a 32-bit MIPS R6 processor but it missed
the 64-bit CPU case leading to FPU failures when requesting FR=1 mode
(which is always the case for MIPS R6 userland) when running a 32-bit
kernel on a 64-bit CPU. We also fix the MIPS R2 case.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: 6134d94923 ("MIPS: asm: fpu: Allow 64-bit FPU on MIPS32 R6")
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: <stable@vger.kernel.org> # 4.0+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10734/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 0e0da48dee ("parisc: mm: don't count preallocated pmds")
introduced a memory leak.
After this commit, the 'return' statement in pmd_free is executed in all
cases. Even for pmd that are not attached to the pgd. So 'free_pages'
can never be called anymore, leading to a memory leak.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Helge Deller <deller@gmx.de>
This single fix reenables ethernet cards for several pxa boards,
broken by regulator addition to dm9000 driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YrDi
-----END PGP SIGNATURE-----
Merge tag 'pxa-fixes-v4.2-rc2' of https://github.com/rjarzmik/linux into fixesD
Merge "pxa fixes for v4.2" from Robert Jarzmik:
ARM: pxa: fixes for v4.2-rc2
This single fix reenables ethernet cards for several pxa boards,
broken by regulator addition to dm9000 driver.
* tag 'pxa-fixes-v4.2-rc2' of https://github.com/rjarzmik/linux:
ARM: pxa: fix dm9000 platform data regression
Alex Bennée