This patch effectively eliminates direct use of pgdat->node_mem_map outside
of the DISCONTIG code. On a flat memory system, these fields aren't
currently used, neither are they on a sparsemem system.
There was also a node_mem_map(nid) macro on many architectures. Its use
along with the use of ->node_mem_map itself was not consistent. It has
been removed in favor of two new, more explicit, arch-independent macros:
pgdat_page_nr(pgdat, pagenr)
nid_page_nr(nid, pagenr)
I called them "pgdat" and "nid" because we overload the term "node" to mean
"NUMA node", "DISCONTIG node" or "pg_data_t" in very confusing ways. I
believe the newer names are much clearer.
These macros can be overridden in the sparsemem case with a theoretically
slower operation using node_start_pfn and pfn_to_page(), instead. We could
make this the only behavior if people want, but I don't want to change too
much at once. One thing at a time.
This patch removes more code than it adds.
Compile tested on alpha, alpha discontig, arm, arm-discontig, i386, i386
generic, NUMAQ, Summit, ppc64, ppc64 discontig, and x86_64. Full list
here: http://sr71.net/patches/2.6.12/2.6.12-rc1-mhp2/configs/
Boot tested on NUMAQ, x86 SMP and ppc64 power4/5 LPARs.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin J. Bligh <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patchset is for supporting a new m32r platform, M3A-2170(Mappi-III)
evaluation board. An M32R chip multiprocessor is equipped on the board.
http://http://www.linux-m32r.org/eng/platform/platform.html
* arch/m32r/Kconfig: Support Mappi-III platform.
* arch/m32r/kernel/Makefile: ditto.
* arch/m32r/kernel/io_mappi3.c: ditto.
* arch/m32r/kernel/setup.c: ditto.
* arch/m32r/kernel/setup_mappi3.c: ditto.
* include/asm-m32r/m32102.h: ditto.
* include/asm-m32r/m32r.h: ditto.
* include/asm-m32r/mappi3/mappi3_pld.h: ditto.
* include/asm-m32r/ide.h: CF support for Mappi-III.
* arch/m32r/kernel/setup_mappi3.c: ditto.
* arch/m32r/mappi3/defconfig.smp: A default config file for Mappi-III.
* arch/m32r/mappi3/dot.gdbinit: A default .gdbinit file for Mappi-III.
* arch/m32r/boot/compressed/m32r_sio.c: Modified for Mappi-III
- At boot time, m32r-g00ff bootloader makes MMU off for Mappi-III,
on the contrary it makes MMU on for Mappi-II.
* arch/m32r/kernel/io_mappi2.c: Update comments.
* arch/m32r/kernel/setup_mappi2.c: ditto.
Signed-off-by: Mamoru Sakugawa <sakugawa@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert most of the current code that uses _NSIG directly to instead use
valid_signal(). This avoids gcc -W warnings and off-by-one errors.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Dave Hansen