As result of the deprecation of the MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block(), all drivers using these
two interfaces need to be updated to use the new pci_enable_msi_range()
and pci_enable_msix_range() interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In order to support local WRITE_INSERT + READ_STRIP operations for
non PI enabled fabrics, the fabric driver needs to be able signal
what protection offload operations are supported.
This is done at session initialization time so the modes can be
signaled by individual se_wwn + se_portal_group endpoints, as well
as optionally across different transports on the same endpoint.
For iser-target, set TARGET_PROT_ALL if the underlying ib_device
has already signaled PI offload support, and allow this to be
exposed via a new iscsit_transport->iscsit_get_sup_prot_ops()
callback.
For loopback, set TARGET_PROT_ALL to signal SCSI initiator mode
operation.
For all other drivers, set TARGET_PROT_NORMAL to disable fabric
level PI.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fastreg is mandatory for signature, so if the
device doesn't support it we don't need to use it.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where outstanding RDMA_READs with WRITE_PENDING
status require an extra target_put_sess_cmd() in isert_put_cmd() code
when called from isert_cq_tx_comp_err() + isert_cq_drain_comp_llist()
context during session shutdown.
The extra kref PUT is required so that transport_generic_free_cmd()
invokes the last target_put_sess_cmd() -> target_release_cmd_kref(),
which will complete(&se_cmd->cmd_wait_comp) the outstanding se_cmd
descriptor with WRITE_PENDING status, and awake the completion in
target_wait_for_sess_cmds() to invoke TFO->release_cmd().
The bug was manifesting itself in target_wait_for_sess_cmds() where
a se_cmd descriptor with WRITE_PENDING status would end up sleeping
indefinately.
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that TASK_ABORTED status is not generated for all cases by
TMR ABORT_TASK + LUN_RESET, a new TFO->abort_task() caller is
necessary in order to give fabric drivers a chance to unmap
hardware / software resources before the se_cmd descriptor is
released via the normal TFO->release_cmd() codepath.
This patch adds TFO->aborted_task() in core_tmr_abort_task()
in place of the original transport_send_task_abort(), and
also updates all fabric drivers to implement this caller.
The fabric drivers that include changes to perform cleanup
via ->aborted_task() are:
- iscsi-target
- iser-target
- srpt
- tcm_qla2xxx
The fabric drivers that currently set ->aborted_task() to
NOPs are:
- loopback
- tcm_fc
- usb-gadget
- sbp-target
- vhost-scsi
For the latter five, there appears to be no additional cleanup
required before invoking TFO->release_cmd() to release the
se_cmd descriptor.
v2 changes:
- Move ->aborted_task() call into transport_cmd_finish_abort (Alex)
Cc: Alex Leung <amleung21@yahoo.com>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Vu Pham <vu@mellanox.com>
Cc: Chris Boot <bootc@bootc.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes isert_conn_create_fastreg_pool() to follow
logic in iscsi_target_locate_portal() for determining how many
FRMR descriptors to allocate based upon the number of possible
per-session command slots that are available.
This addresses an OOPs in isert_reg_rdma() where due to the
use of ISCSI_DEF_XMIT_CMDS_MAX could end up returning a bogus
fast_reg_descriptor when the number of active tags exceeded
the original hardcoded max.
Note this also includes moving isert_conn_create_fastreg_pool()
from isert_connect_request() to isert_put_login_tx() before
posting the final Login Response PDU in order to determine the
se_nacl->queue_depth (eg: number of tags) per session the target
will be enforcing.
v2 changes:
- Move isert_conn->conn_fr_pool list_head init into
isert_conn_request()
v3 changes:
- Drop unnecessary list_empty() check in isert_reg_rdma()
(Sagi)
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If during data-transfer a data-integrity error was detected we
must fail the command with CHECK_CONDITION and not execute
the command.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove code duplication from RDMA_READ and RDMA_WRITE
completions that do basically the same check.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If protection is involved, iSER target must wait for
completion of RDMA_READ before sending SCSI response.
So we must consider that when calculating post_send_buf_count
additions, also when processing good/error completions.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As REG_SIG_MR work request and it's LOCAL_INVALIDATE are
not accounted in post_send_buf_count we must color these
with ISER_FASTREG_LI_WRID in order to process their error
completions when the QP flushes.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case the Target core passed transport T10 protection
operation:
1. Register data buffer (data memory region)
2. Register protection buffer if exsists (prot memory region)
3. Register signature region (signature memory region)
- use work request IB_WR_REG_SIG_MR
4. Execute RDMA
5. Upon RDMA completion check the signature status
- if succeeded send good SCSI response
- if failed send SCSI bad response with appropriate sense buffer
(Fix up compile error in isert_reg_sig_mr, and fix up incorrect
se_cmd->prot_type -> TARGET_PROT_NORMAL comparision - nab)
(Fix failed sector assignment in isert_completion_rdma_* - Sagi + nab)
(Fix enum assignements for protection type - Sagi)
(Fix devision on 32-bit in isert_completion_rdma_* - Sagi + Fengguang)
(Fix context change for v3.14-rc6 code - nab)
(Fix iscsit_build_rsp_pdu inc_statsn flag usage - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case of protected transactions, we will need to check the
protection status of the transaction before sending SCSI response.
So be ready for RDMA_WRITE completions. currently we don't ask
for these completions, but for T10-PI we will.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Introduce pi_context to hold relevant RDMA protection resources.
We eliminate data_key_valid boolean and replace it with indicators
container to indicate:
- Is the descriptor protected (registered via signature MR)
- Is the data_mr key valid (can spare LOCAL_INV WR)
- Is the prot_mr key valid (can spare LOCAL_INV WR)
- Is the sig_mr key valid (can spare LOCAL_INV WR)
Upon connection establishment check if network portal is T10-PI
enabled and allocate T10-PI resources if necessary, allocate
signature enabled memory regions and mark connection queue-pair
as signature enabled.
(Fix context change for v3.14-rc6 code - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
export map/unmap data buffer to a routine that may
be used in various places in the code and keep the
mapping data in a designated descriptor. Also, let
isert_fast_reg_mr to decide weather to use global
MR or do fast registration.
This commit does not change any functionality.
(Fix context change for v3.14-rc6 code - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- The biggest change is core API extensions and mlx5 low-level driver
support for handling DIF/DIX-style protection information, and the
addition of PI support to the iSER initiator. Target support will be
arriving shortly through the SCSI target tree.
- A nice simplification to the "umem" memory pinning library now that
we have chained sg lists. Kudos to Yishai Hadas for realizing our
code didn't have to be so crazy.
- Another nice simplification to the sg wrappers used by qib, ipath and
ehca to handle their mapping of memory to adapter.
- The usual batch of fixes to bugs found by static checkers etc. from
intrepid people like Dan Carpenter and Yann Droneaud.
- A large batch of cxgb4, ocrdma, qib driver updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ww6H
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.15:
- The biggest change is core API extensions and mlx5 low-level driver
support for handling DIF/DIX-style protection information, and the
addition of PI support to the iSER initiator. Target support will
be arriving shortly through the SCSI target tree.
- A nice simplification to the "umem" memory pinning library now that
we have chained sg lists. Kudos to Yishai Hadas for realizing our
code didn't have to be so crazy.
- Another nice simplification to the sg wrappers used by qib, ipath
and ehca to handle their mapping of memory to adapter.
- The usual batch of fixes to bugs found by static checkers etc.
from intrepid people like Dan Carpenter and Yann Droneaud.
- A large batch of cxgb4, ocrdma, qib driver updates"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (102 commits)
RDMA/ocrdma: Unregister inet notifier when unloading ocrdma
RDMA/ocrdma: Fix warnings about pointer <-> integer casts
RDMA/ocrdma: Code clean-up
RDMA/ocrdma: Display FW version
RDMA/ocrdma: Query controller information
RDMA/ocrdma: Support non-embedded mailbox commands
RDMA/ocrdma: Handle CQ overrun error
RDMA/ocrdma: Display proper value for max_mw
RDMA/ocrdma: Use non-zero tag in SRQ posting
RDMA/ocrdma: Memory leak fix in ocrdma_dereg_mr()
RDMA/ocrdma: Increment abi version count
RDMA/ocrdma: Update version string
be2net: Add abi version between be2net and ocrdma
RDMA/ocrdma: ABI versioning between ocrdma and be2net
RDMA/ocrdma: Allow DPP QP creation
RDMA/ocrdma: Read ASIC_ID register to select asic_gen
RDMA/ocrdma: SQ and RQ doorbell offset clean up
RDMA/ocrdma: EQ full catastrophe avoidance
RDMA/cxgb4: Disable DSGL use by default
RDMA/cxgb4: rx_data() needs to hold the ep mutex
...
Unregister the inet notifier during ocrdma unload to avoid a panic after
driver unload.
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Clean up code. Also modifying GSI QP to error during ocrdma_close is fixed.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Issue mailbox commands to query ocrdma controller information and phy
information and print them while adding ocrdma device.
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
As part of SRQ receive buffers posting we populate a non-zero tag
which will be returned in SRQ receive completions.
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Increment the ABI version count for driver/library interface.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
While loading RoCE driver be2net driver should check for ABI version
to catch functional incompatibilities.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allow creating DPP QP even if inline-data is not requested. This is an
optimization to lower latency.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
ocrdma driver selects execution path based on sli_family and asic
generation number. This introduces code to read the asic gen number
from pci register instead of obtaining it from the Emulex NIC driver.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Stale entries in the CQ being destroyed causes hardware to generate
EQEs indefinitely for a given CQ. Thus causing uncontrolled execution
of irq_handler. This patch fixes this using following sementics:
* irq_handler will ring EQ doorbell atleast once and implement budgeting scheme.
* cq_destroy will count number of valid entires during destroy and ring
cq-db so that hardware does not generate uncontrolled EQE.
* cq_destroy will synchronize with last running irq_handler instance.
* arm_cq will always defer arming CQ till poll_cq, except for the first arm_cq call.
* poll_cq will always ring cq-db with arm=SET if arm_cq was called prior to enter poll_cq.
* poll_cq will always ring cq-db with arm=UNSET if arm_cq was not called prior to enter poll_cq.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Current hardware doesn't correctly support DSGL.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
To avoid racing with other threads doing close/flush/whatever, rx_data()
should hold the endpoint mutex.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a race between ULP threads doing an accept/reject, and the
ingress processing thread handling close/abort for the same connection.
The accept/reject path needs to hold the lock to serialize these paths.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
[ Fold in locking fix found by Dan Carpenter <dan.carpenter@oracle.com>.
- Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
The code that resolves the passive side source MAC within the rdma_cm
connection request handler was both redundant and buggy, so remove it.
It was redundant since later, when an RC QP is modified to RTR state,
the resolution will take place in the ib_core module. It was buggy
because this callback also deals with UD SIDR exchange, for which we
incorrectly looked at the REQ member of the CM event and dereferenced
a random value.
Fixes: dd5f03beb4 ("IB/core: Ethernet L2 attributes in verbs/cm structures")
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
These methods appear to only mimic the sg_dma_address() and
sg_dma_len() behavior.
They can be safely removed.
Suggested-by: Bart Van Assche <bvanassche@acm.org>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The removal of these methods is compensated for by code changes to
.map_sg to insure that the vanilla sg_dma_address() and sg_dma_len()
will do the same thing as the equivalent former ib_sg_dma_address()
and ib_sg_dma_len() calls into the drivers.
The introduction of this patch required that the struct
ipath_dma_mapping_ops be converted to a C99 initializer.
Suggested-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Remove the overload for .dma_len and .dma_address
The removal of these methods is compensated for by code changes to
.map_sg to insure that the vanilla sg_dma_address() and sg_dma_len()
will do the same thing as the equivalent former ib_sg_dma_address()
and ib_sg_dma_len() calls into the drivers.
Suggested-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Tested-by: Vinod Kumar <vinod.kumar@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Update Mellanox copyrights for 2014 on the iser initiator driver.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add an iser info print with the local/remote QP information carried
out when the connection is established. While here, fix a little
leftover from the T10 work and set a debug print to be carried in
debug and not info level.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The iscsi stack has existing mechanisms to link back and forth between
the iscsi connection and the iscsi transport (e.g iser/tcp) connection.
This is done through a dd_data pointer field in struct iscsi_conn
which can be set to point to the transport connection, etc.
The iscsi_iser_conn structure was used to get this linking done in
another way, which is uneeded and adds extra complication to the iser
code, so we just remove it.
Signed-off-by: Ariel Nahum <arieln@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The iser disconnection flow isn't done before all the inflight
recv/send buffers posted to the QP are either flushed or normally
completed to the CQ that serves this connection. The condition check
is done in iser_handle_comp_error().
Currently, it's possible for the send buffer completion that makes the
posted send buffers counter reach zero to be polled in the drain tx
call, which is after the rx cq is fully drained. Since this
completion might be not an error one (for example, it might be a
completion of the logout request iSCSI PDU) we will skip
iser_handle_comp_error(). So the connection will never terminate from
the iscsi stack point of view, and we hang.
To resolve this race, do the draining of the tx cq before the loop on
the rx cq.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix pr_err (printk) format warning:
drivers/infiniband/ulp/iser/iser_verbs.c:1181:4: warning: format '%lx' expects argument of type 'long unsigned int', but argument 3 has type 'sector_t' [-Wformat]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
My static checker complains that the sprintf() here can overflow.
drivers/infiniband/hw/mlx4/main.c:1836 mlx4_ib_alloc_eqs()
error: format string overflow. buf_size: 32 length: 69
This seems like a valid complaint. The "dev->pdev->bus->name" string
can be 48 characters long. I just made the buffer 80 characters instead
of 69 and I changed the sprintf() to snprintf().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The code was indented too far and also kernel style says we should have
curly braces.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Running with DMA_API_DEBUG enabled and not checking for DMA mapping
errors triggers a kernel stack trace with "DMA-API: device driver
failed to check map error" message. Add these checks to the MAD
module, both to be be more robust and also eliminate these
false-positive stack traces.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In case of error when writing to userspace, function ehca_create_cq()
does not set an error code before following its error path.
This patch sets the error code to -EFAULT when ib_copy_to_udata()
fails.
This was caught when using spatch (aka. coccinelle)
to rewrite call to ib_copy_{from,to}_udata().
Link: 75ebf2c103:ib_copy_udata.cocci
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In case of error when writing to userspace, the function mthca_create_cq()
does not set an error code before following its error path.
This patch sets the error code to -EFAULT when ib_copy_to_udata() fails.
This was caught when using spatch (aka. coccinelle)
to rewrite call to ib_copy_{from,to}_udata().
Link: 75ebf2c103:ib_copy_udata.cocci
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If kmalloc() fails in c4iw_alloc_ucontext(), the function
leaves but does not set an error code in ret variable:
it will return 0 to the caller.
This patch set ret to -ENOMEM in such case.
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Steve Wise <swise@chelsio.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code which is dealing with SRIOV alias GUIDs in the mlx4 IB driver has some
logic which operated according to the maximal possible active functions (PF + VFs).
After the single port VFs code integration this resulted in a flow of false-positive
warnings going to the kernel log after the PF driver started the alias GUID work.
Fix it by referring to the actual number of functions.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing an MPA Start Request, if the listening endpoint is
DEAD, then abort the connection.
If the IWCM returns an error, then we must abort the connection and
release resources. Also abort_connection() should not post a CLOSE
event, so clean that up too.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
These are generated by HW in some error cases and need to be
silently discarded.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If cxgb4_ofld_send() returns < 0, then send_fw_pass_open_req() must
free the request skb and the saved skb with the tcp header.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Avoid that srp_terminate_io() can access req->scmnd after it has been
cleared by the I/O completion code. Do this by protecting req->scmnd
accesses from srp_terminate_io() via locking
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If a cable is pulled while srp_connect_target() is in progress
that can result in that function never to return. That makes the
process, e.g. srp_daemon, that invoked this function unkillable.
Avoid this by letting srp_connect_target() finish if the event
IB_CM_TIMEWAIT_EXIT is received. This patch fixes a hang with the
following call trace:
[<ffffffff814eae85>] schedule_timeout+0x215/0x2e0
[<ffffffff814eab03>] wait_for_common+0x123/0x180
[<ffffffff814eac1d>] wait_for_completion+0x1d/0x20
[<ffffffffa03b398c>] srp_connect_target+0x1dc/0x410 [ib_srp]
[<ffffffffa03b5809>] srp_create_target+0xba9/0xe70 [ib_srp]
[<ffffffff8133e590>] dev_attr_store+0x20/0x30
[<ffffffff811eb8f5>] sysfs_write_file+0xe5/0x170
[<ffffffff811767c8>] vfs_write+0xb8/0x1a0
[<ffffffff811770c1>] sys_write+0x51/0x90
[<ffffffff8100b072>] system_call_fastpath+0x16/0x1b
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Avoid that stopping srp_daemon takes unusually long due to a cable
pull by making writing into the "add_target" sysfs attribute
interruptible.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The connection uniqueness check is performed before a new connection
is added to the target list. This patch protects both actions by a
mutex such that simultaneous writes from two different threads into the
"add_target" variable do not result in duplicate connections.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Log sgid and dgid when reporting that a login has been rejected or when
a host has been added. This makes it easy to figure out which initiator
and target ports these messages apply to.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
In wrapped commands, we need to verify and convert
the slave's port into the real physical port.
Furthermore, when sending the response back to the slave,
a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
The slave assumes that sqpn is used for QP1 communication.
If the slave is assigned to a port != (first port), we need
to adjust the sqpn that will direct its QP1 packets into the
correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
In B0 steering, gid[5] contains the port. It needs
to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
When a slave queries the hardware, it needs to view only
the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
The QP port is encoded in the sched_qp, thus in modify_qp we need
to encode the correct port in sched_qp.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some code in the mlx4 IB driver stack assumed MLX4_MAX_PORTS ports.
Instead, we should only loop until the number of actual ports in i
the device, which is stored in dev->caps.num_ports.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning directly is easier to read than do-nothing gotos. Remove the
duplicative check on "olp" and pull the code in one indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Improve performance by changing the behavour of the driver when all
SDMA descriptors are in use, and the processes adding new descriptors
are single- or multi-rail.
For single-rail processes, the driver will block the call and finish
posting all SDMA descriptors onto the hardware queue before returning
back to PSM. Repeated kernel calls are slower than blocking.
For multi-rail processes, the driver will return to PSM as quick as
possible so PSM can feed packets to other rail. If all hardware
queues are full, PSM will buffer the remaining SDMA descriptors until
notified by interrupt that space is available.
This patch builds a red-black tree to track the number rails opened by
a particular PID. If the number is more than one, it is a multi-rail
PSM process, otherwise, it is a single-rail process.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: John A Gregor <john.a.gregor@intel.com>
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: CQ Tang <cq.tang@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We cannot save the mapped length using the rdma max_page_list_len field
of the ib_fast_reg_page_list struct because the core code uses it. This
results in an incorrect unmap of the page list in c4iw_free_fastreg_pbl().
I found this with dma mapping debugging enabled in the kernel. The
fix is to save the length in the c4iw_fr_page_list struct.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Based on original work from Jay Hernandez <jay@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Always release the neigh entry in rx_pkt().
Based on original work by Santosh Rastapur <santosh@chelsio.com>.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
find_route() must treat loopback as a valid egress interface.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a four byte hole at the end of the "uresp" struct after the
->qid_mask member.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
These sizes should be unsigned so we don't allow negative values and
have underflow bugs. These can come from the user so there may be
security implications, but I have not tested this.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
After allocating a scsi_host we set protection types and guard type
supported.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Alex Tabachnik <alext@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Once the iSCSI transaction is completed we must implement
check_protection in order to notify on DIF errors that may have
occured.
The routine boils down to calling ib_check_mr_status to get the
signature status of the transaction.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Alex Tabachnik <alext@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add logic to initialize protection information entities. Upon each
iSCSI task, we keep the scsi_cmnd in order to query the scsi
protection operations and reference to protection buffers.
Modify iser_fast_reg_mr to receive indication whether it is
registering the data or protection buffers.
In addition introduce iser_reg_sig_mr which performs fast registration
work-request for a signature enabled memory region
(IB_WR_REG_SIG_MR). In this routine we set all the protection
relevants for the device to offload protection data-transfer and
verification.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Alex Tabachnik <alext@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
During connection establishment we also initialize T10-PI resources
(QP, PI contexts) in order to support SCSI's protection operations.
Signed-off-by: Alex Tabachnik <alext@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use modparams to activate protection information support.
pi_enable bool: Based on this parameter iSER will know if it should
support T10-PI. We don't want to do this by default as it requires to
allocate and initialize extra resources. In case pi_enable=N, iSER
won't publish to SCSI midlayer any DIF capabilities.
pi_guard int: Based on this parameter iSER will publish DIX guard type
support to SCSI midlayer. 0 means CRC is allowed to be passed in DIX
buffers, 1 (or non-zero) means IP-CSUM is allowed to be passed in DIX
buffers. Note that over the wire, only CRC is allowed.
In the next phase, it is worth considering passing these parameters
from iscsid via nlmsg. This will allow these parameters to be
connection based rather than global.
Signed-off-by: Alex Tabachnik <alext@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Unaligned SG-lists may also happen for protection information.
Generalize bounce buffer routine to handle any iser_data_buf which may
be data and/or protection.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This routines operates on data buffers and may also work with
protection infomation buffers. So we generalize them to handle an
iser_data_buf which can be the command data or command protection
information.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In T10-PI support we will have memory keys for protection buffers and
signature transactions. We prefer to compact indicators rather than
keeping multiple bools.
This commit does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Alex Tabachnik <alext@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For T10-PI offload support, we will need to know the device signature
offload capability upon every connection establishment.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Alex Tabachnik <alext@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
fastreg descriptor will include protection information context. In
order to place the logic in one place we introduce iser_create_fr_desc
function.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Alex Tabachnik <alext@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This is a preparation step for T10-PI offload support. We prefer to
push the desicion of which mkey to use (global or fastreg) to
iser_fast_reg_mr. We choose to do this since in T10-PI we may need to
register for protection buffers and in this case we wish to simplify
iser_fast_reg_mr instead of repeating the logic of which key to use.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Alex Tabachnik <alext@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
FRWR stands for "fast registration work request". We want to avoid
calling the fastreg pool with that name, instead we name it fastreg
which stands for "fast registration".
This pool will include more elements in the future, so it is a good
idea to generalize the name.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Alex Tabachnik <alext@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In case iSER uses fast registration method, it should not request for
successful completions on fast registration nor local invalidate
requests. We color wr_id with ISER_FRWR_LI_WRID in order to correctly
consume error completions.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix the following warning for the mlx4 driver:
$ make M=drivers/infiniband C=2 CF=-D__CHECK_ENDIAN__
drivers/infiniband/hw/mlx4/qp.c:1885:31: warning: restricted __be16 degrades to integer
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
drivers/infiniband/hw/ocrdma/ocrdma_verbs.c: In function ‘_ocrdma_modify_qp’:
drivers/infiniband/hw/ocrdma/ocrdma_verbs.c:1299:31: error: ‘old_qps’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
status = ocrdma_mbx_modify_qp(dev, qp, attr, attr_mask, old_qps);
ocrdma_mbx_modify_qp() (and subsequent calls) doesn't appear to use old_qps
so it doesn't need to be passed on. Removing the variable results in the
warning going away.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Devesh Sharma (Devesh.sharma@emulex.com)
Signed-off-by: Roland Dreier <roland@purestorage.com>
We don't need to test "ret" twice and also the white space is messed up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We already know "pusable" is non-zero, no need to check again.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
%pa format already prints in hexadecimal format, so remove the '0x' annotation
to avoid a double '0x0x' pattern.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In case of error while accessing to userspace memory, function
nes_create_qp() returns NULL instead of an error code wrapped through
ERR_PTR(). But NULL is not expected by ib_uverbs_create_qp(), as it
check for error with IS_ERR().
As page 0 is likely not mapped, it is going to trigger an Oops when
the kernel will try to dereference NULL pointer to access to struct
ib_qp's fields.
In some rare cases, page 0 could be mapped by userspace, which could
turn this bug to a vulnerability that could be exploited: the function
pointers in struct ib_device will be under userspace total control.
This was caught when using spatch (aka. coccinelle)
to rewrite calls to ib_copy_{from,to}_udata().
Link: https://www.gitorious.org/opteya/ib-hw-nes-create-qp-null
Link: 75ebf2c103:ib_copy_udata.cocci
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In qib_create_ctxts() we allocate an array to hold recv contexts. Then attempt
to create data for those recv contexts. If that call to qib_create_ctxtdata()
fails then an error is returned but the previously allocated memory is not
freed.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit af061a644a add some code in qib_ib_rcv() which
trigger a warning from coccicheck (coccinelle/spatch):
$ make C=2 CHECK=scripts/coccicheck drivers/infiniband/hw/qib/
CHECK drivers/infiniband/hw/qib/qib_verbs.c
drivers/infiniband/hw/qib/qib_verbs.c:679:5-32: code aligned with following code on line 681
CC [M] drivers/infiniband/hw/qib/qib_verbs.o
In fact, according to similar code in qib_kreceive(),
qib_ib_rcv() code is correct but improperly indented.
This patch fix indentation for the misaligned portion.
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: infinipath@intel.com
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: cocci@systeme.lip6.fr
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit c804f07248 moved qib_assign_ctxt() to
do_qib_user_sdma_queue_create() but dropped the braces
around the statements.
This was spotted by coccicheck (coccinelle/spatch):
$ make C=2 CHECK=scripts/coccicheck drivers/infiniband/hw/qib/
CHECK drivers/infiniband/hw/qib/qib_file_ops.c
drivers/infiniband/hw/qib/qib_file_ops.c:1583:2-23: code aligned with following code on line 1587
This patch adds braces back.
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: infinipath@intel.com
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: cocci@systeme.lip6.fr
Cc: stable@vger.kernel.org
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The counters, unicast_xmit, unicast_rcv, multicast_xmit, multicast_rcv
are now maintained as percpu variables.
The mad code is modified to add a z_ latch so that the percpu counters
monotonically increase with appropriate adjustments in the reset,
read logic to maintain the z_ latch.
This patch also corrects the fact the unitcast_xmit wasn't handled
at all for UC and RC QPs.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch replaces the dd->int_counter with a percpu counter.
The maintanance of qib_stats.sps_ints and int_counter are
combined into the new counter.
There are two new functions added to read the counter:
- qib_int_counter (for a particular qib_devdata)
- qib_sps_ints (for all HCAs)
A z_int_counter is added to allow the interrupt detection logic
to determine if interrupts have occured since z_int_counter
was "reset".
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The debugfs init code was incorrectly called before the idr mechanism
is used to get the unit number, so the dd->unit hasn't been
initialized. This caused the unit relative directory creation to fail
after the first.
This patch moves the init for the debugfs stuff until after all of the
failures and after the unit number has been determined.
A bug in unwind code in qib_alloc_devdata() is also fixed.
Cc: <stable@vger.kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Guard against a potential buffer overrun. The size to read from the
user is passed in, and due to the padding that needs to be taken into
account, as well as the place holder for the ICRC it is possible to
overflow the 32bit value which would cause more data to be copied from
user space than is allocated in the buffer.
Cc: <stable@vger.kernel.org>
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Guard against a potential buffer overrun. Right now the qib driver is
protected by the fact that the data structure in question is only 16
bits. Should that ever change the problem will be exposed. There is a
similar defect in the ipath driver and this brings the two code paths
into sync.
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fixes to enable the negotiation of the supported IRD/ORD sizes with
the peer when exchanging MPA v2 messages in connection establishment.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The current logic suffers from a slow response time to disable user DB
usage, and also fails to avoid DB FIFO drops under heavy load. This commit
fixes these deficiencies and makes the avoidance logic more optimal.
This is done by more efficiently notifying the ULDs of potential DB
problems, and implements a smoother flow control algorithm in iw_cxgb4,
which is the ULD that puts the most load on the DB fifo.
Design:
cxgb4:
Direct ULD callback from the DB FULL/DROP interrupt handler. This allows
the ULD to stop doing user DB writes as quickly as possible.
While user DB usage is disabled, the LLD will accumulate DB write events
for its queues. Then once DB usage is reenabled, a single DB write is
done for each queue with its accumulated write count. This reduces the
load put on the DB fifo when reenabling.
iw_cxgb4:
Instead of marking each qp to indicate DB writes are disabled, we create
a device-global status page that each user process maps. This allows
iw_cxgb4 to only set this single bit to disable all DB writes for all
user QPs vs traversing the idr of all the active QPs. If the libcxgb4
doesn't support this, then we fall back to the old approach of marking
each QP. Thus we allow the new driver to work with an older libcxgb4.
When the LLD upcalls iw_cxgb4 indicating DB FULL, we disable all DB writes
via the status page and transition the DB state to STOPPED. As user
processes see that DB writes are disabled, they call into iw_cxgb4
to submit their DB write events. Since the DB state is in STOPPED,
the QP trying to write gets enqueued on a new DB "flow control" list.
As subsequent DB writes are submitted for this flow controlled QP, the
amount of writes are accumulated for each QP on the flow control list.
So all the user QPs that are actively ringing the DB get put on this
list and the number of writes they request are accumulated.
When the LLD upcalls iw_cxgb4 indicating DB EMPTY, which is in a workq
context, we change the DB state to FLOW_CONTROL, and begin resuming all
the QPs that are on the flow control list. This logic runs on until
the flow control list is empty or we exit FLOW_CONTROL mode (due to
a DB DROP upcall, for example). QPs are removed from this list, and
their accumulated DB write counts written to the DB FIFO. Sets of QPs,
called chunks in the code, are removed at one time. The chunk size is 64.
So 64 QPs are resumed at a time, and before the next chunk is resumed, the
logic waits (blocks) for the DB FIFO to drain. This prevents resuming to
quickly and overflowing the FIFO. Once the flow control list is empty,
the db state transitions back to NORMAL and user QPs are again allowed
to write directly to the user DB register.
The algorithm is designed such that if the DB write load is high enough,
then all the DB writes get submitted by the kernel using this flow
controlled approach to avoid DB drops. As the load lightens though, we
resume to normal DB writes directly by user applications.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Anand Priyadarshee <anandp@chelsio.com>.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
To activate RoCE/SRIOV, need to remove the following:
1. In mlx4_ib_add, need to remove the error return preventing
initialization of a RoCE port under SRIOV.
2. In update_vport_qp_params (in resource_tracker.c) need to remove
the error return when a RoCE RC or UD qp is detected.
This error return causes the INIT-to-RTR qp transition to fail
in the wrapper function under RoCE/SRIOV.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Handle CM_SIDR_REQ_ATTR_ID and CM_SIDR_REP_ATTR_ID
in multiplex_cm_handler and demux_cm_handler.
* Handle Service ID Resolution messages and REQ messages
separately, for their formats are different.
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,
This is achieved as follows:
Outgoing MADs:
1. Source MAC: obtained from the CQ completion structure
(struct ib_wc, smac field).
2. Destination MAC: obtained from the tunnel header
3. vlan_id: obtained from the tunnel header.
Incoming MADs
1. The source (i.e., remote) MAC and vlan_id are passed in
the tunnel header to the proxy QP1.
VST mode support:
For outgoing MADs, the vlan_id obtained from the header is
discarded, and the vlan_id specified by the Hypervisor is used
instead.
For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
"invalid" vlan (0xffff) is substituted when forwarding to the slave.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IB side of RoCE requires the MAC table index of the
MAC address used by its QPs.
To obtain the real MAC index, the IB side registers the
MAC (increasing its ref count, and also returning the
real MAC index) during the modify-qp sequence.
This protects against the ETH side deleting or modifying
that MAC table entry while the QP is active.
Note that until the modify-qp command returns success,
the MAC and VLAN information only has "candidate" status.
If the modify-qp succeeds, the "candidate" info is promoted
to the operational MAC/VLAN info for the qp. If the modify fails,
the candidate MAC/VLAN is unregistered, and the old qp info
is preserved.
The patch is a bit complex, because there are multiple qp
transitions where the primary-path information may be
modified: INIT-to-RTR, and SQD-to-SQD.
Similarly for the alternate path information.
Therefore the code must handle cases where path information
has already been entered into the QP context by previous
qp transitions.
For the MAC address, the success logic is as follows:
1. If there was no previous MAC, simply move the candidate
MAC information to the operational information, and reset
the candidate MAC info.
2. If there was a previous MAC, unregister it. Then move
the MAC information from candidate to operational, and
reset the candidate info (as in 1. above).
The MAC address failure logic is the same for all cases:
- Unregister the candidate MAC, and reset the candidate MAC info.
For Vlan registration, the logic is similar.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GIDs are statically distributed, as follows:
PF: gets 16 GIDs
VFs: Remaining GIDS are divided evenly between VFs activated by the driver.
If the division is not even, lower-numbered VFs get an extra GID.
For an IB interface, the number of gids per guest remains as before: one gid per guest.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This requires the following modifications:
1. Fix build_mlx4_header to properly fill in the ETH fields
2. Adjust mux and demux QP1 flow to support RoCE.
This commit still assumes only one GID per slave for RoCE.
The commit enabling multiple GIDs is a subsequent commit, and
is done separately because of its complexity.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SCSI target fixes from Nicholas Bellinger:
"This series addresses a number of outstanding issues wrt to active I/O
shutdown using iser-target. This includes:
- Fix a long standing tpg_state bug where a tpg could be referenced
during explicit shutdown (v3.1+ stable)
- Use list_del_init for iscsi_cmd->i_conn_node so list_empty checks
work as expected (v3.10+ stable)
- Fix a isert_conn->state related hung task bug + ensure outstanding
I/O completes during session shutdown. (v3.10+ stable)
- Fix isert_conn->post_send_buf_count accounting for RDMA READ/WRITEs
(v3.10+ stable)
- Ignore FRWR completions during active I/O shutdown (v3.12+ stable)
- Fix command leakage for interrupt coalescing during active I/O
shutdown (v3.13+ stable)
Also included is another DIF emulation fix from Sagi specific to
v3.14-rc code"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
Target/sbc: Fix sbc_copy_prot for offset scatters
iser-target: Fix command leak for tx_desc->comp_llnode_batch
iser-target: Ignore completions for FRWRs in isert_cq_tx_work
iser-target: Fix post_send_buf_count for RDMA READ/WRITE
iscsi/iser-target: Fix isert_conn->state hung shutdown issues
iscsi/iser-target: Use list_del_init for ->i_conn_node
iscsi-target: Fix iscsit_get_tpg_from_np tpg_state bug
Currently support only T10-DIF types of signature handover operations
(types 1|2|3).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This commit takes care of the generated signature error CQE generated
by the HW (if happened). The underlying mlx5 driver will handle
signature error completions and will mark the relevant memory region
as dirty.
Once the consumer gets the completion for the transaction, it must
check for signature errors on signature memory region using a new
lightweight verb ib_check_mr_status().
In case the user doesn't check for signature error (i.e. doesn't call
ib_check_mr_status() with status check IB_MR_CHECK_SIG_STATUS), the
memory region cannot be used for another signature operation
(REG_SIG_MR work request will fail).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch implements IB_WR_REG_SIG_MR posted by the user.
Baisically this WR involves 3 WQEs in order to prepare and properly
register the signature layout:
1. post UMR WR to register the sig_mr in one of two possible ways:
* In case the user registered a single MR for data so the UMR data segment
consists of:
- single klm (data MR) passed by the user
- BSF with signature attributes requested by the user.
* In case the user registered 2 MRs, one for data and one for protection,
the UMR consists of:
- strided block format which includes data and protection MRs and
their repetitive block format.
- BSF with signature attributes requested by the user.
2. post SET_PSV in order to set the memory domain initial
signature parameters passed by the user.
SET_PSV is not signaled and solicited CQE.
3. post SET_PSV in order to set the wire domain initial
signature parameters passed by the user.
SET_PSV is not signaled and solicited CQE.
* After this compound WR we place a small fence for next WR to come.
This patch also introduces some helper functions to set the BSF correctly
and determining the signature format selectors.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
get_umr_flags helper function might be used for types of access modes
other than ACCESS_MODE_MTT, such as ACCESS_MODE_KLM. So remove it from
helper, and callers will add their own access mode flag.
This commit does not add/change functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
As a preliminary step for signature feature which will require posting
multiple (3) WQEs for a single WR, we break post_send routine WQE
indexing into begin and finish routines.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If user requested signature enable we initialize relevant mlx5_ib_qp
members. We mark the qp as sig_enable and we increase the effective
SQ size, but still limit the user max_send_wr to original size
computed. We also allow the create_qp routine to accept sig_enable
create flag.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Support create_mr and destroy_mr verbs. Creating ib_mr may be done
for either ib_mr that will register regular page lists like
alloc_fast_reg_mr routine, or indirect ib_mrs that can register other
(pre-registered) ib_mrs in an indirect manner.
In addition user may request signature enable, that will mean that the
created ib_mr may be attached with signature attributes (BSF, PSVs).
Currently we only allow direct/indirect registration modes.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Introduce a verbs interface for signature-related operations. A
signature handover operation configures the layouts of data and
protection attributes both in memory and wire domains.
Signature operations are:
- INSERT:
Generate and insert protection information when handing over
data from input space to output space.
- validate and STRIP:
Validate protection information and remove it when handing over
data from input space to output space.
- validate and PASS:
Validate protection information and pass it when handing over
data from input space to output space.
Once the signature handover opration is done, the HCA will offload
data integrity generation/validation while performing the actual data
transfer.
Additions:
1. HCA signature capabilities in device attributes
Verbs provider supporting signature handover operations fills
relevant fields in device attributes structure returned by
ib_query_device.
2. QP creation flag IB_QP_CREATE_SIGNATURE_EN
Creating a QP that will carry signature handover operations may
require some special preparations from the verbs provider. So we
add QP creation flag IB_QP_CREATE_SIGNATURE_EN to declare that the
created QP may carry out signature handover operations. Expose
signature support to verbs layer (no support for now).
3. New send work request IB_WR_REG_SIG_MR
Signature handover work request. This WR will define the signature
handover properties of the memory/wire domains as well as the
domains layout. The purpose of this work request is to bind all
the needed information for the signature operation:
- data to be transferred: wr->sg_list (ib_sge).
* The raw data, pre-registered to a single MR (normally, before
signature, this MR would have been used directly for the data
transfer)
- data protection guards: sig_handover.prot (ib_sge).
* The data protection buffer, pre-registered to a single MR, which
contains the data integrity guards of the raw data blocks.
Note that it may not always exist, only in cases where the user is
interested in storing protection guards in memory.
- signature operation attributes: sig_handover.sig_attrs.
* Tells the HCA how to validate/generate the protection information.
Once the work request is executed, the memory region that will
describe the signature transaction will be the sig_mr. The
application can now go ahead and send the sig_mr.rkey or use the
sig_mr.lkey for data transfer.
4. New Verb ib_check_mr_status
check_mr_status verb checks the status of the memory region post
transaction. The first check that may be used is
IB_MR_CHECK_SIG_STATUS, which will indicate if any signature
errors are pending for a specific signature-enabled ib_mr. This
verb is a lightwight check and is allowed to be taken from
interrupt context. An application must call this verb after it is
known that the actual data transfer has finished.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This commit introduces verbs for creating/destoying memory
regions which will allow new types of memory key operations such
as protected memory registration.
Indirect memory registration is registering several (one
of more) pre-registered memory regions in a specific layout.
The Indirect region may potentialy describe several regions
and some repitition format between them.
Protected Memory registration is registering a memory region
with various data integrity attributes which will describe protection
schemes that will be handled by the HCA in an offloaded manner.
These memory regions will be applicable for a new REG_SIG_MR
work request introduced later in this patchset.
In the future these routines may replace or implement current memory
regions creation routines existing today:
- ib_reg_user_mr
- ib_alloc_fast_reg_mr
- ib_get_dma_mr
- ib_dereg_mr
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch addresses a number of active I/O shutdown issues
related to isert_cmd descriptors being leaked that are part
of a completion interrupt coalescing batch.
This includes adding logic in isert_cq_tx_comp_err() to
drain any associated tx_desc->comp_llnode_batch, as well
as isert_cq_drain_comp_llist() to drain any associated
isert_conn->conn_comp_llist.
Also, set tx_desc->llnode_active in isert_init_send_wr()
in order to determine when work requests need to be skipped
in isert_cq_tx_work() exception path code.
Finally, update isert_init_send_wr() to only allow interrupt
coalescing when ISER_CONN_UP.
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.13+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes IB_WR_FAST_REG_MR + IB_WR_LOCAL_INV related
work requests to include a ISER_FRWR_LI_WRID value in order to
signal isert_cq_tx_work() that these requests should be ignored.
This is necessary because even though IB_SEND_SIGNALED is not
set for either work request, during a QP failure event the work
requests will be returned with exception status from the TX
completion queue.
v2 changes:
- Rename ISER_FRWR_LI_WRID -> ISER_FASTREG_LI_WRID (Sagi)
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes the incorrect setting of ->post_send_buf_count
related to RDMA WRITEs + READs where isert_rdma_rw->send_wr_num
was not being taken into account.
This includes incrementing ->post_send_buf_count within
isert_put_datain() + isert_get_dataout(), decrementing within
__isert_send_completion() + isert_response_completion(), and
clearing wr->send_wr_num within isert_completion_rdma_read()
This is necessary because even though IB_SEND_SIGNALED is
not set for RDMA WRITEs + READs, during a QP failure event
the work requests will be returned with exception status
from the TX completion queue.
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a couple of different hug shutdown issues
related to wait_event() + isert_conn->state. First, it changes
isert_conn->conn_wait + isert_conn->conn_wait_comp_err from
waitqueues to completions, and sets ISER_CONN_TERMINATING from
within isert_disconnect_work().
Second, it splits isert_free_conn() into isert_wait_conn() that
is called earlier in iscsit_close_connection() to ensure that
all outstanding commands have completed before continuing.
Finally, it breaks isert_cq_comp_err() into seperate TX / RX
related code, and adds logic in isert_cq_rx_comp_err() to wait
for outstanding commands to complete before setting ISER_CONN_DOWN
and calling complete(&isert_conn->conn_wait_comp_err).
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There are a handful of uses of list_empty() for cmd->i_conn_node
within iser-target code that expect to return false once a cmd
has been removed from the per connect list.
This patch changes all uses of list_del -> list_del_init in order
to ensure that list_empty() returns false as expected.
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactors the IB core umem code and vendor drivers to use a
linear (chained) SG table instead of chunk list. With this change the
relevant code becomes clearer—no need for nested loops to build and
use umem.
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor fixes this time to v3.14-rc1 related changes. Also
included is one fix for a free after use regression in persistent
reservations UNREGISTER logic that is CC'ed to >= v3.11.y stable"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
Target/sbc: Fix protection copy routine
IB/srpt: replace strict_strtoul() with kstrtoul()
target: Simplify command completion by removing CMD_T_FAILED flag
iser-target: Fix leak on failure in isert_conn_create_fastreg_pool
iscsi-target: Fix SNACK Type 1 + BegRun=0 handling
target: Fix missing length check in spc_emulate_evpd_83()
qla2xxx: Remove last vestiges of qla_tgt_cmd.cmd_list
target: Fix 32-bit + CONFIG_LBDAF=n link error w/ sector_div
target: Fix free-after-use regression in PR unregister
We should use rdma_vlan_dev_real_dev() instead of using vlan_dev_real_dev()
when building the GID table for a vlan interface.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use correct value for obtaining traffic class from device
response for Query QP request.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We use "tx_desc" again after we free it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix a possible NULL pointer dereference in disconnection flow. This
can happen if the target disconnected/rejected the connection request,
e.g before the binding stage between iscsi connection to the transport
connection.
Signed-off-by: Alex Tabachnik <alext@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Error reported at http://marc.info/?l=linux-rdma&m=138995755801039&w=2
Fix short to int cast for big endian systems.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Remove Kconfig dependency of mlx5_ib/mlx5_core on X86, since there is
no such dependency in reality.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Research has shown that commit a77fcf8950 ("IB/qib: Use a single
txselect module parameter for serdes tuning") missed a key serdes init
sequence.
This patch add that sequence.
Cc: <stable@vger.kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For userspace RoCE UD QPs we need to know the GID format that the
kernel uses, e.g when working over older kernels. For that end, add a
new port capability IB_PORT_IP_BASED_GIDS and report it when query
port is issued.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When scanning netdevices we need to check a few more conditions and
cases to build the IBoE GID table properly. For example, under
bonding we must make sure that when a port is down, the bond IP
address isn't programmed as a GID, since doing so will cause failure
with IB core flows that selects ports by GID.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The IBoE code used to reset the GID table did it for all Ethernet
ports of the device. Since the whole architecture of generating GIDs
and responding to events is port-based, this is inefficient and can
lead to wrong content in the GID table. Change the reset flow to be
per-port.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Updating the GID table under IBoE requires read/write from/to shared
data structures. These data structures are protected with the device
iboe lock. The flows that modify the GID table start from
1. Initializing the GID table
2. NETDEV events
3. INET or INET6 events
This patch makes sure that the flow of initializing the GID table is
consistent with the other two flows w.r.t on what step the lock is taken.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
On the one hand, the invocation of netdev_master_upper_dev_get()
within mlx4_ib_scan_netdevs() must be done with rtnl lock held. On
the other hand, it's wrong to call rtnl_lock() from within this
function since it's also called by our netdev notifier callback.
Therefore move the locking to mlx4_ib_add() so that both cases are
covered.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Make sure that for Ethernet ports, the port GID table index 0 is always
occupied with a default GID of the relevant IPv6 link-local adderss.
This provides better user experience for legacy applications that don't use
the RDMA CM and were working on index 0 prior to the IP addressing change.
Also, as GIDs are generated from IP addresses of the network devices that
are associated with the port, it's basically possible that the GID table
will be empty if no IP address was assigned. This doesn't comply with the
IB spec section 4.1.1 "GID usage and properties".
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When the device has only Ethernet ports, don't try to allocate range
of steerable UD QPs since they aren't needed. This fixes an issue
where mlx4 VFs tried to allocate a range of UD steerable QPs, but
failed to do so.
Fixes: c1c9850112 ("IB/mlx4: Add support for steerable IB UD QPs")
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Set the return variable to an error code as done elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set the return variable to an error code as done elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently Connect-IB does not support blocking multicast loopback, so
don't set IB_DEVICE_BLOCK_MULTICAST_LOOPBACK in the device caps.
Reported by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit c1be5232d2 ("Fix micro UAR allocator") broke binary compatibility
between libmlx5 and mlx5_ib since it defines a different value to the number
of micro UARs per page, leading to wrong calculation in libmlx5. This patch
defines struct mlx5_ib_alloc_ucontext_req_v2 as an extension to struct
mlx5_ib_alloc_ucontext_req. The extended size is determined in mlx5_ib_alloc_ucontext()
and in case of old library we use uuarn 0 which works fine -- this is
acheived due to create_user_qp() falling back from high to medium then to
low class where low class will return 0. For new libraries we use the
more sophisticated allocation algorithm.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix the RC QPs send queue overhead computation to take into account
two additional segments in the WQE which are needed for registration
operations.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- add support for SCSI Referrals (Hannes)
- add support for T10 DIF into target core (nab + mkp)
- add support for T10 DIF emulation in FILEIO + RAMDISK backends (Sagi + nab)
- add support for T10 DIF -> bio_integrity passthrough in IBLOCK backend (nab)
- prep changes to iser-target for >= v3.15 T10 DIF support (Sagi)
- add support for qla2xxx N_Port ID Virtualization - NPIV (Saurav + Quinn)
- allow percpu_ida_alloc() to receive task state bitmask (Kent)
- fix >= v3.12 iscsi-target session reset hung task regression (nab)
- fix >= v3.13 percpu_ref se_lun->lun_ref_active race (nab)
- fix a long-standing network portal creation race (Andy)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
target: Fix percpu_ref_put race in transport_lun_remove_cmd
target/iscsi: Fix network portal creation race
target: Report bad sector in sense data for DIF errors
iscsi-target: Convert gfp_t parameter to task state bitmask
iscsi-target: Fix connection reset hang with percpu_ida_alloc
percpu_ida: Make percpu_ida_alloc + callers accept task state bitmask
iscsi-target: Pre-allocate more tags to avoid ack starvation
qla2xxx: Configure NPIV fc_vport via tcm_qla2xxx_npiv_make_lport
qla2xxx: Enhancements to enable NPIV support for QLOGIC ISPs with TCM/LIO.
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
IB/isert: pass scatterlist instead of cmd to fast_reg_mr routine
IB/isert: Move fastreg descriptor creation to a function
IB/isert: Avoid frwr notation, user fastreg
IB/isert: seperate connection protection domains and dma MRs
tcm_loop: Enable DIF/DIX modes in SCSI host LLD
target/rd: Add DIF protection into rd_execute_rw
target/rd: Add support for protection SGL setup + release
target/rd: Refactor rd_build_device_space + rd_release_device_space
target/file: Add DIF protection support to fd_execute_rw
target/file: Add DIF protection init/format support
...
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
This patch propigates the use of task state bitmask now used by
percpu_ida_alloc() up the iscsi-target callchain, replacing the
use of GFP_ATOMIC for TASK_RUNNING, and GFP_KERNEL for
TASK_INTERRUPTIBLE.
Also, drop the unnecessary gfp_t parameter to isert_allocate_cmd(),
and just pass TASK_INTERRUPTIBLE into iscsit_allocate_cmd().
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Verify that reserved fields in struct mlx5_ib_resize_cq are cleared
before continuing execution of the verb. This is required to allow
making use of this area in future revisions.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The current code attmepts to call ib_umem_get() even if the length is
zero, which causes a failure. Since the spec allows zero length work
queues, change the code so we don't call ib_umem_get() in those cases.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Implement resize CQ which is a mandatory verb in mlx5.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Modify CQ is used by ULPs like IPoIB to change moderation parameters. This
patch adds support in mlx5.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Put a wmb() to make sure the doorbell record is visible to the HCA before we
hit doorbell.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use the possibly more efficient ether_addr_equal() instead of memcmp().
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The GSI QP type is compatible with and should be allowed to send data
to/from any UD QP. This was found when testing ibacm on the same node
as an SA.
Cc: <stable@vger.kernel.org>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Building mem.o for 32 bits x86 triggers a GCC warning:
drivers/infiniband/hw/cxgb4/mem.c: In function '_c4iw_write_mem_dma_aligned':
drivers/infiniband/hw/cxgb4/mem.c:79:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Silence that warning by casting "&wr_wait" to unsigned long before
casting it to __be64. That's what _c4iw_write_mem_inline() already does.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a path in handle_vq() where kmem_cache_free() can be called
with pointer to a local variable. It can happen if vq_repbuf_alloc()
failed to allocate memory from cache and req is NULL.
The patch adds check if cache memory was allocated before freeing it.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Svetlana Mavrina <another.karnil@gmail.com>
Reviewed-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Roland Dreier <roland@purestorage.com>
After booting without a working link, "ip link" shows:
5: mlx4_ib1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 2044 qdisc pfifo_fast
state DOWN qlen 256
...
7: mlx4_ib1.8003@mlx4_ib1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 2044 qdisc
pfifo_fast state DOWN qlen 256
...
Then after connecting and disconnecting the link, which should result
in exactly the same state as before, it shows:
5: mlx4_ib1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 2044 qdisc pfifo_fast
state DOWN qlen 256
...
7: mlx4_ib1.8003@mlx4_ib1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 2044 qdisc
pfifo_fast state LOWERLAYERDOWN qlen 256
...
Notice the (now correct) LOWERLAYERDOWN operstate shown for the
mlx4_ib1.8003 interface. Ideally the identical state would be shown
right after boot.
The problem is related to the calling of netif_carrier_off() in
network drivers. For a long time it was known that doing
netif_carrier_off() before registering the netdevice would result in
the interface's operstate being shown as UNKNOWN if the device was
brought up without a working link. This problem was fixed in commit
8f4cccbbd9 ('net: Set device operstate at registration time'), but
still there remains the minor inconsistency demonstrated above.
This patch fixes it by moving ipoib's call to netif_carrier_off() into
the .ndo_open method, which is where network drivers ordinarily do it.
With the patch when doing the same test as above, the operstate of
mlx4_ib1.8003 is shown as LOWERLAYERDOWN right after boot.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix the below "make W=1" build warning:
drivers/infiniband/core/iwcm.c: In function ‘destroy_cm_id’:
drivers/infiniband/core/iwcm.c:330: warning: variable ‘ret’ set but not used
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If addr is not a linklocal address, the code incorrectly fails to
return and ends up assigning the scope ID to the scope id of the
address, which is wrong. Fix by checking if it's a link local address
first, and immediately return 0 if not.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This is called from qp_grp_and_vf_bind() and we are holding the
vf->lock so the allocation can't sleep.
Fixes: e3cf00d0a8 ('IB/usnic: Add Cisco VIC low-level hardware driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The rport timers must be stopped before the SRP initiator destroys the
resources associated with the SCSI host. This is necessary because
otherwise the callback functions invoked from the SRP transport layer
could trigger a use-after-free. Stopping the rport timers before
invoking scsi_remove_host() can trigger long delays in the SCSI error
handler if a transport layer failure occurs while scsi_remove_host()
is in progress. Hence move the code for stopping the rport timers from
srp_rport_release() into a new function and invoke that function after
scsi_remove_host() has finished. This patch fixes the following
sporadic kernel crash:
kernel BUG at include/asm-generic/dma-mapping-common.h:64!
invalid opcode: 0000 [#1] SMP
RIP: 0010:[<ffffffffa03b20b1>] [<ffffffffa03b20b1>] srp_unmap_data+0x121/0x130 [ib_srp]
Call Trace:
[<ffffffffa03b20fc>] srp_free_req+0x3c/0x80 [ib_srp]
[<ffffffffa03b2188>] srp_finish_req+0x48/0x70 [ib_srp]
[<ffffffffa03b21fb>] srp_terminate_io+0x4b/0x60 [ib_srp]
[<ffffffffa03a6fb5>] __rport_fail_io_fast+0x75/0x80 [scsi_transport_srp]
[<ffffffffa03a7438>] rport_fast_io_fail_timedout+0x88/0xc0 [scsi_transport_srp]
[<ffffffff8108b370>] worker_thread+0x170/0x2a0
[<ffffffff81090876>] kthread+0x96/0xa0
[<ffffffff8100c0ca>] child_rip+0xa/0x20
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Now that ocrdma supports IP-based addressing, we need to depend on
INET, since ocrdma registers itself for net device events.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Since mlx4_ib supports IP based addressing, a dependency on INET needs
to be added, since mlx4_ib registers itself for net device events.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add the missing unlock before return from function cm_init_qp_rtr_attr()
in the error handling case.
Fixes: dd5f03beb4 ("IB/core: Ethernet L2 attributes in verbs/cm structures")
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Roland Dreier <roland@purestorage.com>
IP based addressing introduces the usage of rdma_addr_find_dmac_by_grh()
within ib_core. Since this function is declared in ib_addr, ib_addr
should be a part of the core INFINIBAND modules, rather than
INFINIBAND_ADDR_TRANS.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Existing user space applications provide only IBoE L3 address
attributes to the kernel when they issue a modify QP modify. To work
with them and let such apps (plus kernel consumers which don't use the
RDMA-CM) keep working transparently under the IBoE GID IP addressing
changes, add an Eth L2 address resolution helper.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch is similar in spirit to the "IB/mlx4: Use IBoE (RoCE) IP
based GIDs in the port GID table" patch.
Changes to inet4 and inet6 addresses for the host are monitored and if
the address is associated with an ocrdma device then a gid is added or
deleted from the device's gid table. The gid format will be a IPv4 to
IPv6 mapped or the IPv6 address.
Cc: Naresh Gottumukkala <bgottumukkala@emulex.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch is similar in spirit to the "IB/mlx4: Handle Ethernet L2
parameters for IP based GID addressing". It handles the fact that IP
based RoCE gids don't store Ethernet L2 parameters, MAC and VLAN.
When building an address handle, instead of parsing the dgid to
get the MAC and VLAN, take them from the address handle attributes.
Cc: Naresh Gottumukkala <bgottumukkala@emulex.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This routine may help for protection registration as well.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This routine may be called both by fast registration
descriptors for data and for integrity buffers.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use fast registration lingo. fast registration will
also incorporate signature/DIF registration.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It is more correct to seperate connections protection domains
and dma_mr handles. protection information support requires to
do so.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
IP based RoCE gids don't store Ethernet L2 parameters, MAC and VLAN.
Therefore, we need to extract them from the CQE and place them in
struct ib_wc (to be used for cases were they were taken from the gid).
Also, when modifying a QP or building address handle, instead of
parsing the dgid to get the MAC and VLAN, take them from the address
handle attributes.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently, the mlx4 driver set IBoE (RoCE) gids to encode related
Ethernet netdevice interface MAC address and possibly VLAN id.
Change this scheme such that gids encode interface IP addresses (both
IP4 and IPv6).
This requires learning the IP addresses which are of use by a
netdevice associated with the HCA port, formatting them to gids and
adding them to the port gid table. Furthermore, events of add and
delete address are caught to maintain the gid table accordingly.
Associated IP addresses may belong to a master of an Ethernet
netdevice on top of that port so this should be considered when
building and maintaining the gid table.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently, the IB core and specifically the RDMA-CM assumes that IBoE
(RoCE) gids encode related Ethernet netdevice interface MAC address
and possibly VLAN id.
Change GIDs to be treated as they encode interface IP address.
Since Ethernet layer 2 address parameters are not longer encoded
within gids, we have to extend the Infiniband address structures (e.g.
ib_ah_attr) with layer 2 address parameters, namely mac and vlan.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set the return variable to an error code as done elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The variable qp_grp is initialized but never used otherwise, so remove
the unused variable.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Roland Dreier <roland@purestorage.com>
usNIC userspace/kernel ABI should be set to 4 instead of 3.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
usNIC default transport is UDP. Hence, advertise RDMA_NODE_USNIC_UDP
by default for usNIC devices.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add the complementary RDMA_NODE_USNIC_UDP for RDMA_TRANSPORT_USNIC_UDP.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
usNIC needs inet notifiers to function correctly, so add a Kconfig
dependency on CONFIG_INET.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch removes the net_random and net_srandom macros and replaces
them with direct calls to the prandom ones. As new commits only seem to
use prandom_u32 there is no use to keep them around.
This change makes it easier to grep for users of prandom_u32.
Signed-off-by: Aruna-Hewapathirane <aruna.hewapathirane@gmail.com>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for Ethernet L2 attributes in the
verbs/cm/cma structures.
When dealing with L2 Ethernet, we should use smac, dmac, vlan ID and priority
in a similar manner that the IB L2 (and the L4 PKEY) attributes are used.
Thus, those attributes were added to the following structures:
* ib_ah_attr - added dmac
* ib_qp_attr - added smac and vlan_id, (sl remains vlan priority)
* ib_wc - added smac, vlan_id
* ib_sa_path_rec - added smac, dmac, vlan_id
* cm_av - added smac and vlan_id
For the path record structure, extra care was taken to avoid the new
fields when packing it into wire format, so we don't break the IB CM
and SA wire protocol.
On the active side, the CM fills. its internal structures from the
path provided by the ULP. We add there taking the ETH L2 attributes
and placing them into the CM Address Handle (struct cm_av).
On the passive side, the CM fills its internal structures from the WC
associated with the REQ message. We add there taking the ETH L2
attributes from the WC.
When the HW driver provides the required ETH L2 attributes in the WC,
they set the IB_WC_WITH_SMAC and IB_WC_WITH_VLAN flags. The IB core
code checks for the presence of these flags, and in their absence does
address resolution from the ib_init_ah_from_wc() helper function.
ib_modify_qp_is_ok is also updated to consider the link layer. Some
parameters are mandatory for Ethernet link layer, while they are
irrelevant for IB. Vendor drivers are modified to support the new
function signature.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch adds support for steerable (NETIF) QP creation. When we
create the device, we allocate a range of steerable QPs.
Afterward when a QP is created with the NETIF flag, it's allocated
from this range. Allocation is managed by bitmap allocator.
Internal steering rules for those QPs is automatically generated on
their creation.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The mlx4 device requires adding IB flow spec to rules that apply over
infiniband link layer. This patch adds a mechanism to add such a rule.
If higher levels e.g. IP/UDP/TCP flow specs are provided, the device
requires us to add an empty wild-carded IB rule. Furthermore, the device
requires the QPN to be put in the rule.
Add here specific parsing support for IB empty rules and the ability
to self-generate missing specs based on existing ones.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Up until now, flow steering wasn't supported when using IB ports.
This patch enables support for flow steering if all hardware ports
support that, for example the new MLX4_DEV_CAP_FLAG2_DMFS_IPOIB mlx4
device capability.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When creating an IPoIB UD QP, provide a hint to the low level driver
that the QP should support flow-steering. This means that privileged
user space applications can steer TCP/IP IPoIB traffic from the
network stack, in a similar manner done with Ethernet RAW_PACKET QPs.
The hint is provided through new QP creation flag called NETIF_QP.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The micro UAR (uuar) allocator had a bug which resulted from the fact
that in each UAR we only have two micro UARs avaialable, those at
index 0 and 1. This patch defines iterators to aid in traversing the
list of available micro UARs when allocating a uuar.
In addition, change the logic in create_user_qp() so that if high
class allocation fails (high class means lower latency), we revert to
medium class and not to the low class.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The variable start in struct mlx5_ib_mr is never used. Remove it.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add comment describing usnic_transport_rsrv port and remove
extraneous space from usnic_transport.c.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use for_each_sg() instead of an explicit for-loop to iterate over
scatter-gather list.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add RDMA_TRANSPORT_USNIC_UDP which will be used by usNIC.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add supports for:
1) Parsing the socket file descriptor pass down from userspace.
2) IP notifiers
3) Encoding the IP in the GID
4) Other aux. changes to support UDP
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch provides API for rest of usNIC code to increment or decrement
socket's reference count. Auxiliary socket APIs are also provided.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add *ip field* to *struct usnic_fwd_dev* as well as new *functions* to
manipulate the *ip field.* Furthermore, add new functions for
programming UDP flows in the forwarding device.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Expand the kernel/userspace interface so userspace may push down
a socket file descriptor to usNIC. Also, bump up the abi and version
numbers.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch ports usnic_ib_sysfs.c to the new interface of
usnic_fwd.h.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch ports usnic_ib_qp_grp.[hc] to the new interface
of usnic_fwd.h.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch ports usnic_ib_main.c, usnic_ib_verbs.c and usnic_ib.h
to the new interface of usnic_fwd.h.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Push all of the usnic device forwarding state - such as mtu, mac - to
usnic_fwd_dev. Furthermore, usnic_fwd.h exposes a improved interface
for rest of the usnic code. The primary improvement is that
usnic_fwd.h's flow management interface takes in high-level *filter*
and *action* structures now, instead of low-level paramaters such as
vnic_idx, rq_idx.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add *struct usnic_transport_spec* for passing around transport
specifications.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
usNIC calls WARN_ON(spin_is_locked..) at few places. In some of these
instances, the call is made while holding a spinlock. Change
all WARN_ON(spin_is_locked...) calls in usNIC to
lockdep_assert_held to make it fool-proof bc the latter can be
called while holding a spinlock and unlike spin_is_locked,
lockdep_assert_held also works correctly on UP.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This adds a driver that allows userspace to use UD-like QPs over a
proprietary Cisco transport with Cisco's Virtual Interface Cards (VICs),
including VIC 1240 and 1280 cards.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
OCRDMA_GEN2_FAMILY is wrongly defined as 0x02 -- it should be 0x0F.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix ah->av->valid bit position and big endian portability.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we create a new infiniband link with uninfiniband device, e.g. `ip link
add link em1 type ipoib pkey 0x8001`. We will get a NULL pointer dereference
cause other dev like Ethernet don't have struct ib_device.
The code path is:
rtnl_newlink
|-- ipoib_new_child_link
|-- __ipoib_vlan_add
|-- ipoib_set_dev_features
|-- ib_query_device
Fix this bug by make sure the src net is infiniband when create new link.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Some holiday bug fixes for 3.13... There is still one bug I'd like to
get fixed before 3.13-final.
The vlan code erroneously assignes the header ops of the underlying
real device to the VLAN device above it when the real device can
hardware offload VLAN handling. That's completely bogus because
header ops are tied to the device type, so they only expect to see a
'dev' argument compatible with their ops.
The fix is the have the VLAN code use a special set of header ops that
does the pass-thru correctly, by calling the underlying real device's
header ops but _also_ passing in the real device instead of the VLAN
device.
That fix is currently waiting some testing.
Anyways, of note here:
1) Fix bitmap edge case in radiotap, from Johannes Berg.
2) Fix oops on driver unload in rtlwifi, from Larry Finger.
3) Bonding doesn't do locking correctly during speed/duplex/link
changes, from Ding Tianhong.
4) Fix header parsing in GRE code, this bug has been around for a few
releases. From Timo Teräs.
5) SIT tunnel driver MTU check needs to take GSO into account, from
Eric Dumazet.
6) Minor info leak in inet_diag, from Daniel Borkmann.
7) Info leak in YAM hamradio driver, from Salva Peiró.
8) Fix route expiration state handling in ipv6 routing code, from Li
RongQing.
9) DCCP probe module does not check request_module()'s return value,
from Wang Weidong.
10) cpsw driver passes NULL device names to request_irq(), from
Mugunthan V N.
11) Prevent a NULL splat in RDS binding code, from Sasha Levin.
12) Fix 4G overflow test in tg3 driver, from Nithin Sujir.
13) Cure use after free in arc_emac and fec driver's software
timestamp handling, from Eric Dumazet.
14) SIT driver can fail to release the route when
iptunnel_handle_offloads() throws an error. From Li RongQing.
15) Several batman-adv fixes from Simon Wunderlich and Antonio
Quartulli.
16) Fix deadlock during TIPC socket release, from Ying Xue.
17) Fix regression in ROSE protocol recvmsg() msg_name handling, from
Florian Westphal.
18) stmmac PTP support releases wrong spinlock, from Vince Bridgers"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
stmmac: Fix incorrect spinlock release and PTP cap detection.
phy: IRQ cannot be shared
net: rose: restore old recvmsg behavior
xen-netback: fix guest-receive-side array sizes
fec: Do not assume that PHY reset is active low
tipc: fix deadlock during socket release
netfilter: nf_tables: fix wrong datatype in nft_validate_data_load()
batman-adv: fix vlan header access
batman-adv: clean nf state when removing protocol header
batman-adv: fix alignment for batadv_tvlv_tt_change
batman-adv: fix size of batadv_bla_claim_dst
batman-adv: fix size of batadv_icmp_header
batman-adv: fix header alignment by unrolling batadv_header
batman-adv: fix alignment for batadv_coded_packet
netfilter: nf_tables: fix oops when updating table with user chains
netfilter: nf_tables: fix dumping with large number of sets
ipv6: release dst properly in ipip6_tunnel_xmit
netxen: Correct off-by-one errors in bounds checks
net: Add some clarification to skb_tx_timestamp() comment.
arc_emac: fix potential use after free
...
Use the possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Faisal Latif <faisal.latif@intel.com>
Cc: linux-rdma@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Additional checks for uverbs to ensure forward compatibility, handle
malformed input better.
- Fix potential use-after-free in iWARP connection manager.
- Make a function static.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=bol6
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"Last batch of InfiniBand/RDMA changes for 3.13 / 2014:
- Additional checks for uverbs to ensure forward compatibility,
handle malformed input better.
- Fix potential use-after-free in iWARP connection manager.
- Make a function static"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/uverbs: Check access to userspace response buffer in extended command
IB/uverbs: Check input length in flow steering uverbs
IB/uverbs: Set error code when fail to consume all flow_spec items
IB/uverbs: Check reserved fields in create_flow
IB/uverbs: Check comp_mask in destroy_flow
IB/uverbs: Check reserved field in extended command header
IB/uverbs: New macro to set pointers to NULL if length is 0 in INIT_UDATA()
IB/core: const'ify inbuf in struct ib_udata
RDMA/iwcm: Don't touch cm_id after deref in rem_ref
RDMA/cxgb4: Make _c4iw_write_mem_dma() static
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check on the output buffer with access_ok(VERIFY_WRITE, ...)
to ensure the whole buffer is in userspace memory before using the
pointer in uverbs functions. If the buffer or a subset of it is not
valid, returns -EFAULT to the caller.
This will also catch invalid buffer before the final call to
copy_to_user() which happen late in most uverb functions.
Just like the check in read(2) syscall, it's a sanity check to detect
invalid parameters provided by userspace. This particular check was added
in vfs_read() by Linus Torvalds for v2.6.12 with following commit message:
https://git.kernel.org/cgit/linux/kernel/git/tglx/history.git/commit/?id=fd770e66c9a65b14ce114e171266cf6f393df502
Make read/write always do the full "access_ok()" tests.
The actual user copy will do them too, but only for the
range that ends up being actually copied. That hides
bugs when the range has been clamped by file size or other
issues.
Note: there's no need to check input buffer since vfs_write() already does
access_ok(VERIFY_READ, ...) as part of write() syscall.
Link: http://marc.info/?i=cover.1387273677.git.ydroneaud@opteya.com
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Since ib_copy_from_udata() doesn't check yet the available input data
length before accessing userspace memory, an explicit check of this
length is required to prevent:
- reading past the user provided buffer,
- underflow when subtracting the expected command size from the input
length.
This will ensure the newly added flow steering uverbs don't try to
process truncated commands.
Link: http://marc.info/?i=cover.1386798254.git.ydroneaud@opteya.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If the flow_spec items parsed count does not match the number of items
declared in the flow_attr command, or if not all bytes are used for
flow_spec items (eg. trailing garbage), a log message is reported and
the function leave through the error path. Unfortunately the error
code is currently not set.
This patch set error code to -EINVAL in such cases, so that the error
is reported to userspace instead of silently fail.
Link: http://marc.info/?i=cover.1386798254.git.ydroneaud@opteya.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
As noted by Daniel Vetter in its article "Botching up ioctls"[1]
"Check *all* unused fields and flags and all the padding for whether
it's 0, and reject the ioctl if that's not the case. Otherwise
your nice plan for future extensions is going right down the
gutters since someone *will* submit an ioctl struct with random
stack garbage in the yet unused parts. Which then bakes in the ABI
that those fields can never be used for anything else but garbage."
It's important to ensure that reserved fields are set to known value,
so that it will be possible to use them latter to extend the ABI.
The same reasonning apply to comp_mask field present in newer uverbs
command: per commit 22878dbc91 ("IB/core: Better checking of
userspace values for receive flow steering"), unsupported values in
comp_mask are rejected.
[1] http://blog.ffwll.ch/2013/11/botching-up-ioctls.html
Link: http://marc.info/?i=cover.1386798254.git.ydroneaud@opteya.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
As noted by Daniel Vetter in its article "Botching up ioctls"[1]
"Check *all* unused fields and flags and all the padding for whether
it's 0, and reject the ioctl if that's not the case. Otherwise
your nice plan for future extensions is going right down the
gutters since someone *will* submit an ioctl struct with random
stack garbage in the yet unused parts. Which then bakes in the ABI
that those fields can never be used for anything else but garbage."
It's important to ensure that reserved fields are set to known value,
so that it will be possible to use them latter to extend the ABI.
The same reasonning apply to comp_mask field present in newer uverbs
command: per commit 22878dbc91 ("IB/core: Better checking of
userspace values for receive flow steering"), unsupported values in
comp_mask are rejected.
[1] http://blog.ffwll.ch/2013/11/botching-up-ioctls.html
Link: http://marc.info/?i=cover.1386798254.git.ydroneaud@opteya.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Trying to have a ternary operator to choose between NULL (or 0) and the
real pointer value in invocations leads to an impossible choice between
a sparse error about a literal 0 used as a NULL pointer, and a gcc
warning about "pointer/integer type mismatch in conditional expression."
Rather than clutter the source with more casts, move the ternary
operator into a new INIT_UDATA_BUF_OR_NULL() macro, which makes it
easier to use and simplifies its callers.
Reported-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch moves INIT_WORK setup for cq_desc->cq_[rx,tx]_work into
isert_create_device_ib_res(), instead of being done each callback
invocation in isert_cq_[rx,tx]_callback().
This also fixes a 'INFO: trying to register non-static key' warning
when cancel_work_sync() is called before INIT_WORK has setup the
struct work_struct.
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Userspace input buffer is not modified by kernel, so it can be 'const'.
This is also a prerequisite to remove the implicit cast
from INIT_UDATA().
Link: http://marc.info/?i=cover.1386798254.git.ydroneaud@opteya.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
rem_ref() calls iwcm_deref_id(), which will wake up any blockers on
cm_id_priv->destroy_comp if the refcnt hits 0. That will unblock
someone in iw_destroy_cm_id() which will free the cmid. If that
happens before rem_ref() calls test_bit(IWCM_F_CALLBACK_DESTROY,
&cm_id_priv->flags), then the test_bit() will touch freed memory.
The fix is to read the bit first, then deref. We should never be in
iw_destroy_cm_id() with IWCM_F_CALLBACK_DESTROY set, and there is a
BUG_ON() to make sure of that.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch marks the function _c4iw_write_mem_dma() as static
because it is not used outside this file, which fixes the warning:
drivers/infiniband/hw/cxgb4/mem.c:176:5: warning: no previous prototype for ‘_c4iw_write_mem_dma’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"Things have been quiet this round with mostly bugfixes, percpu
conversions, and other minor iscsi-target conformance testing changes.
The highlights include:
- Add demo_mode_discovery attribute for iscsi-target (Thomas)
- Convert tcm_fc(FCoE) to use percpu-ida pre-allocation
- Add send completion interrupt coalescing for ib_isert
- Convert target-core to use percpu-refcounting for se_lun
- Fix mutex_trylock usage bug in iscsit_increment_maxcmdsn
- tcm_loop updates (Hannes)
- target-core ALUA cleanups + prep for v3.14 SCSI Referrals support (Hannes)
v3.14 is currently shaping to be a busy development cycle in target
land, with initial support for T10 Referrals and T10 DIF currently on
the roadmap"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits)
iscsi-target: chap auth shouldn't match username with trailing garbage
iscsi-target: fix extract_param to handle buffer length corner case
iscsi-target: Expose default_erl as TPG attribute
target_core_configfs: split up ALUA supported states
target_core_alua: Make supported states configurable
target_core_alua: Store supported ALUA states
target_core_alua: Rename ALUA_ACCESS_STATE_OPTIMIZED
target_core_alua: spellcheck
target core: rename (ex,im)plict -> (ex,im)plicit
percpu-refcount: Add percpu-refcount.o to obj-y
iscsi-target: Do not reject non-immediate CmdSNs exceeding MaxCmdSN
iscsi-target: Convert iscsi_session statistics to atomic_long_t
target: Convert se_device statistics to atomic_long_t
target: Fix delayed Task Aborted Status (TAS) handling bug
iscsi-target: Reject unsupported multi PDU text command sequence
ib_isert: Avoid duplicate iscsit_increment_maxcmdsn call
iscsi-target: Fix mutex_trylock usage in iscsit_increment_maxcmdsn
target: Core does not need blkdev.h
target: Pass through I/O topology for block backstores
iser-target: Avoid using FRMR for single dma entry requests
...
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=xxC+
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (66 commits)
IB/core: Re-enable create_flow/destroy_flow uverbs
IB/core: extended command: an improved infrastructure for uverbs commands
IB/core: Remove ib_uverbs_flow_spec structure from userspace
IB/core: Use a common header for uverbs flow_specs
IB/core: Make uverbs flow structure use names like verbs ones
IB/core: Rename 'flow' structs to match other uverbs structs
IB/core: clarify overflow/underflow checks on ib_create/destroy_flow
IB/ucma: Convert use of typedef ctl_table to struct ctl_table
IB/cm: Convert to using idr_alloc_cyclic()
IB/mlx5: Fix page shift in create CQ for userspace
IB/mlx4: Fix device max capabilities check
IB/mlx5: Fix list_del of empty list
IB/mlx5: Remove dead code
IB/core: Encorce MR access rights rules on kernel consumers
IB/mlx4: Fix endless loop in resize CQ
RDMA/cma: Remove unused argument and minor dead code
RDMA/ucma: Discard events for IDs not yet claimed by user space
IB/core: Add Cisco usNIC rdma node and transport types
RDMA/nes: Remove self-assignment from nes_query_qp()
IB/srp: Report receive errors correctly
...
This commit reverts commit 7afbddfae9 ("IB/core: Temporarily disable
create_flow/destroy_flow uverbs"). Since the uverbs extensions
functionality was experimental for v3.12, this patch re-enables the
support for them and flow-steering for v3.13.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 400dbc9658 ("IB/core: Infrastructure for extensible uverbs
commands") added an infrastructure for extensible uverbs commands
while later commit 436f2ad05a ("IB/core: Export ib_create/destroy_flow
through uverbs") exported ib_create_flow()/ib_destroy_flow() functions
using this new infrastructure.
According to the commit 400dbc9658, the purpose of this
infrastructure is to support passing around provider (eg. hardware)
specific buffers when userspace issue commands to the kernel, so that
it would be possible to extend uverbs (eg. core) buffers independently
from the provider buffers.
But the new kernel command function prototypes were not modified to
take advantage of this extension. This issue was exposed by Roland
Dreier in a previous review[1].
So the following patch is an attempt to a revised extensible command
infrastructure.
This improved extensible command infrastructure distinguish between
core (eg. legacy)'s command/response buffers from provider
(eg. hardware)'s command/response buffers: each extended command
implementing function is given a struct ib_udata to hold core
(eg. uverbs) input and output buffers, and another struct ib_udata to
hold the hw (eg. provider) input and output buffers.
Having those buffers identified separately make it easier to increase
one buffer to support extension without having to add some code to
guess the exact size of each command/response parts: This should make
the extended functions more reliable.
Additionally, instead of relying on command identifier being greater
than IB_USER_VERBS_CMD_THRESHOLD, the proposed infrastructure rely on
unused bits in command field: on the 32 bits provided by command
field, only 6 bits are really needed to encode the identifier of
commands currently supported by the kernel. (Even using only 6 bits
leaves room for about 23 new commands).
So this patch makes use of some high order bits in command field to
store flags, leaving enough room for more command identifiers than one
will ever need (eg. 256).
The new flags are used to specify if the command should be processed
as an extended one or a legacy one. While designing the new command
format, care was taken to make usage of flags itself extensible.
Using high order bits of the commands field ensure that newer
libibverbs on older kernel will properly fail when trying to call
extended commands. On the other hand, older libibverbs on newer kernel
will never be able to issue calls to extended commands.
The extended command header includes the optional response pointer so
that output buffer length and output buffer pointer are located
together in the command, allowing proper parameters checking. This
should make implementing functions easier and safer.
Additionally the extended header ensure 64bits alignment, while making
all sizes multiple of 8 bytes, extending the maximum buffer size:
legacy extended
Maximum command buffer: 256KBytes 1024KBytes (512KBytes + 512KBytes)
Maximum response buffer: 256KBytes 1024KBytes (512KBytes + 512KBytes)
For the purpose of doing proper buffer size accounting, the headers
size are no more taken in account in "in_words".
One of the odds of the current extensible infrastructure, reading
twice the "legacy" command header, is fixed by removing the "legacy"
command header from the extended command header: they are processed as
two different parts of the command: memory is read once and
information are not duplicated: it's making clear that's an extended
command scheme and not a different command scheme.
The proposed scheme will format input (command) and output (response)
buffers this way:
- command:
legacy header +
extended header +
command data (core + hw):
+----------------------------------------+
| flags | 00 00 | command |
| in_words | out_words |
+----------------------------------------+
| response |
| response |
| provider_in_words | provider_out_words |
| padding |
+----------------------------------------+
| |
. <uverbs input> .
. (in_words * 8) .
| |
+----------------------------------------+
| |
. <provider input> .
. (provider_in_words * 8) .
| |
+----------------------------------------+
- response, if present:
+----------------------------------------+
| |
. <uverbs output space> .
. (out_words * 8) .
| |
+----------------------------------------+
| |
. <provider output space> .
. (provider_out_words * 8) .
| |
+----------------------------------------+
The overall design is to ensure that the extensible infrastructure is
itself extensible while begin more reliable with more input and bound
checking.
Note:
The unused field in the extended header would be perfect candidate to
hold the command "comp_mask" (eg. bit field used to handle
compatibility). This was suggested by Roland Dreier in a previous
review[2]. But "comp_mask" field is likely to be present in the uverb
input and/or provider input, likewise for the response, as noted by
Matan Barak[3], so it doesn't make sense to put "comp_mask" in the
header.
[1]:
http://marc.info/?i=CAL1RGDWxmM17W2o_era24A-TTDeKyoL6u3NRu_=t_dhV_ZA9MA@mail.gmail.com
[2]:
http://marc.info/?i=CAL1RGDXJtrc849M6_XNZT5xO1+ybKtLWGq6yg6LhoSsKpsmkYA@mail.gmail.com
[3]:
http://marc.info/?i=525C1149.6000701@mellanox.com
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://marc.info/?i=cover.1383773832.git.ydroneaud@opteya.com
[ Convert "ret ? ret : 0" to the equivalent "ret". - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
The structure holding any types of flow_spec is of no use to
userspace. It would be wrong for userspace to do:
struct ib_uverbs_flow_spec flow_spec;
flow_spec.type = IB_FLOW_SPEC_TCP;
flow_spec.size = sizeof(flow_spec);
Instead, userspace should use the dedicated flow_spec structure for
- Ethernet : struct ib_uverbs_flow_spec_eth,
- IPv4 : struct ib_uverbs_flow_spec_ipv4,
- TCP/UDP : struct ib_uverbs_flow_spec_tcp_udp.
In other words, struct ib_uverbs_flow_spec is a "virtual" data
structure that can only be use by the kernel as an alias to the other.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://marc.info/?i=cover.1383773832.git.ydroneaud@opteya.com
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch adds "flow" prefix to most of data structure added as part
of commit 436f2ad05a ("IB/core: Export ib_create/destroy_flow through
uverbs") to keep those names in sync with the data structures added in
commit 319a441d13 ("IB/core: Add receive flow steering support").
It's just a matter of translating 'ib_flow' to 'ib_uverbs_flow'.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://marc.info/?i=cover.1383773832.git.ydroneaud@opteya.com
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 436f2ad05a ("IB/core: Export ib_create/destroy_flow through
uverbs") added public data structures to support receive flow
steering. The new structs are not following the 'uverbs' pattern:
they're lacking the common prefix 'ib_uverbs'.
This patch replaces ib_kern prefix by ib_uverbs.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://marc.info/?i=cover.1383773832.git.ydroneaud@opteya.com
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch fixes the following issues:
1. Unneeded checks were removed
2. Removed the fixed size out of flow_attr.size, thus simplifying the checks.
3. Remove a 32bit hole on 64bit systems with strict alignment in
struct ib_kern_flow_att by adding a reserved field.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 3e6628c4b3 ("idr: introduce idr_alloc_cyclic()") adds a new
idr_alloc_cyclic() routine and converts several of these users to it.
This is just a missed one - add it.
Signed-off-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
When creating a CQ, we must use mlx5 adapter page shift.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Move the check on max supported CQEs after the final number of entries is
evaluated.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The value of the local variable index is never used in reg_mr_callback().
Signed-off-by: Eli Cohen <eli@mellanox.com>
[ Remove now-unused variable delta too. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Enforce the rule that when requesting remote write or atomic permissions, local
write must be indicated as well. See IB spec 11.2.8.2.
Spotted by: Hagay Abramovsky <hagaya@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When calling get_sw_cqe() we need pass the consumer_index and not the
masked value. Failure to do so will cause incorrect result of
get_sw_cqe() possibly leading to endless loop.
This problem was reported and analyzed by Michael Rice from HP.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* lookup_one_len() really wants i_mutex held on directory.
* leaks galore - just mount ipathfs, then
cd /sys/bus/pci/drivers/qib_ib; echo *:*:*.* >unbind
on a box with that card present and try to umount ipathfs...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch avoids a duplicate iscsit_increment_maxcmdsn() call for
ISER_IB_RDMA_WRITE within isert_map_rdma() + isert_reg_rdma_frwr(),
which will already be occuring once during isert_put_datain() ->
iscsit_build_rsp_pdu() operation.
It also removes the local conn->stat_sn assignment + increment,
and changes the third parameter to iscsit_build_rsp_pdu() to
signal this should be done by iscsi_target_mode code.
Tested-by: Moussa Ba <moussaba@micron.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes isert_reg_rdma_frwr() to not use FRMR for single
dma entry requests from small I/Os, in order to avoid the associated
memory registration overhead.
Using DMA MR is sufficient here for the single dma entry requests,
and addresses a >= v3.12 performance regression.
Signed-off-by: Vu Pham <vu@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The dev variable is never assigned after being initialised.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Problem reported by Avneesh Pant <avneesh.pant@oracle.com>:
It looks like we are triggering a bug in RDMA CM/UCM interaction.
The bug specifically hits when we have an incoming connection
request and the connecting process dies BEFORE the passive end of
the connection can process the request i.e. it does not call
rdma_get_cm_event() to retrieve the initial connection event. We
were able to triage this further and have some additional
information now.
In the example below when P1 dies after issuing a connect request
as the CM id is being destroyed all outstanding connects (to P2)
are sent a reject message. We see this reject message being
received on the passive end and the appropriate CM ID created for
the initial connection message being retrieved in cm_match_req().
The problem is in the ucma_event_handler() code when this reject
message is delivered to it and the initial connect message itself
HAS NOT been delivered to the client. In fact the client has not
even called rdma_cm_get_event() at this stage so we haven't
allocated a new ctx in ucma_get_event() and updated the new
connection CM_ID to point to the new UCMA context.
This results in the reject message not being dropped in
ucma_event_handler() for the new connection request as the
(if (!ctx->uid)) block is skipped since the ctx it refers to is
the listen CM id context which does have a valid UID associated
with it (I believe the new CMID for the connection initially
uses the listen CMID -> context when it is created in
cma_new_conn_id). Thus the assumption that new events for a
connection can get dropped in ucma_event_handler() is incorrect
IF the initial connect request has not been retrieved in the
first case. We end up getting a CM Reject event on the listen CM
ID and our upper layer code asserts (in fact this event does not
even have the listen_id set as that only gets set up librdmacm
for connect requests).
The solution is to verify that the cm_id being reported in the event
is the same as the cm_id referenced by the ucma context. A mismatch
indicates that the ucma context corresponds to the listen. This fix
was validated by using a modified version of librdmacm that was able
to verify the problem and see that the reject message was indeed
dropped after this patch was applied.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch adds new rdma node and new rdma transport, and supporting
code used by Cisco's low latency driver called usNIC. usNIC uses its
own transport, distinct from IB and iWARP.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Assigning a value to itself is pointless.
Spotted with coverity, no hardware to test.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The IB spec does not guarantee that the opcode is available in error
completions. Hence do not rely on it. See also commit 948d1e889e
("IB/srp: Introduce srp_handle_qp_err()").
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: <stable@vger.kernel.org> # v3.8
Signed-off-by: Roland Dreier <roland@purestorage.com>
If SCSI commands are submitted with a SCSI request timeout that is
lower than the the IB RC timeout, it can happen that the SCSI error
handler has already started device recovery before transport layer
error handling starts. So it can happen that the SCSI error handler
tries to abort a SCSI command after it has been reset by
srp_rport_reconnect().
Tell the SCSI error handler that such commands have finished and that
it is not necessary to continue its recovery strategy for commands
that have been reset by srp_rport_reconnect().
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Remove an SRP target from the SRP target list before invoking the last
scsi_host_put() call. This change is necessary because that last put
frees the memory that holds the srp_target_port structure.
This patch prevents the following kernel oops:
RIP: 0010:[<ffffffff810b00d0>] __lock_acquire+0x500/0x1570
Call Trace:
[<ffffffff810b11e4>] lock_acquire+0xa4/0x120
[<ffffffff81531206>] _spin_lock+0x36/0x70
[<ffffffffa01b6d8f>] srp_remove_work+0xef/0x180 [ib_srp]
[<ffffffff8109125c>] worker_thread+0x21c/0x3d0
[<ffffffff81096e86>] kthread+0x96/0xa0
[<ffffffff8100c20a>] child_rip+0xa/0x20
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
[ bvanassche - Modified path description and CC'ed stable. ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently, it's not possible to change queue depth for a device behind
SRP host. Sometimes, we need to adjust queue_depth for performance
reason (eg storage busy, we need lower queue_depth to avoid running
into SCSI error handler), so this patch add support for SRP driver.
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Certain storage configurations, e.g. a sufficiently large array of
hard disks in a RAID configuration, need a queue depth above 64 to
achieve optimal performance. Hence make the queue depth configurable.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Tested-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Vu Pham <vu@mellanox.com>
Cc: Sebastian Riemer <sebastian.riemer@profitbricks.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
On an initiator system with multiple IB ports it is not yet possible
to figure out what the originating port of an SRP connection is. Hence
make the source GID available in sysfs.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
After a transport layer occurred, periodically try to reconnect
to the target until the dev_loss timer expires. Protect the
callback functions that can be invoked from inside the SCSI EH
against concurrent invocation with srp_reconnect_rport() via the
rport mutex. Change the default dev_loss_tmo from 60s into 600s
to give the reconnect mechanism a chance to kick in.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add support for periodically reconnecting to an SRP target until
the dev_loss timer expires. After the tenth reconnection attempt,
gradually slow down subsequent reconnect attempts.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Start the reconnect timer, fast_io_fail timer and dev_loss timers if a
transport layer error occurs.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Enable fast_io_fail_tmo and dev_loss_tmo functionality for the IB SRP
initiator. Add kernel module parameters that allow to specify default
values for these parameters.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Keep the rport data structure around after srp_remove_host() has
finished until cleanup of the IB transport layer has finished
completely. This is necessary because later patches use the rport
pointer inside the queuecommand callback. Without this patch
accessing the rport from inside a queuecommand callback is racy
because srp_remove_host() must be invoked before scsi_remove_host()
and because the queuecommand callback could get invoked after
srp_remove_host() has finished. In other words, without this patch
the queuecommand callback can get invoked after the rport data
structure has been freed.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allow the InfiniBand RC retry count to be configured by the user as an
option in the target login string. Reducing this retry count allows to
reduce the path failover time.
Signed-off-by: Vu Pham <vu@mellanox.com>
[ bvanassche: Rewrote patch description / changed default retry count ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 7fac33014f54("IB/qib: checkpatch fixes") was overzealous in
removing a simple_strtoul for a parse routine, setup_txselect(). That
routine is required to handle a multi-value string.
Unwind that aspect of the fix.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Convert __attribute__ ((packed)) to __packed.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
qib_user_sdma_queue_pkts() gets called with mmap_sem held for
writing. Except for get_user_pages() deep down in
qib_user_sdma_pin_pages() we don't seem to need mmap_sem at all. Even
more interestingly the function qib_user_sdma_queue_pkts() (and also
qib_user_sdma_coalesce() called somewhat later) call copy_from_user()
which can hit a page fault and we deadlock on trying to get mmap_sem
when handling that fault.
So just make qib_user_sdma_pin_pages() use get_user_pages_fast() and
leave mmap_sem locking for mm.
This deadlock has actually been observed in the wild when the node
is under memory pressure.
Cc: <stable@vger.kernel.org>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Roland Dreier <roland@purestorage.com>
ipath_user_sdma_queue_pkts() gets called with mmap_sem held for
writing. Except for get_user_pages() deep down in
ipath_user_sdma_pin_pages() we don't seem to need mmap_sem at all.
Even more interestingly the function ipath_user_sdma_queue_pkts() (and
also ipath_user_sdma_coalesce() called somewhat later) call
copy_from_user() which can hit a page fault and we deadlock on trying
to get mmap_sem when handling that fault. So just make
ipath_user_sdma_pin_pages() use get_user_pages_fast() and leave
mmap_sem locking for mm.
This deadlock has actually been observed in the wild when the node
is under memory pressure.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
[ Merged in fix for call to get_user_pages_fast from Tetsuo Handa
<penguin-kernel@I-love.SAKURA.ne.jp>. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Remove the redundant check of comparing if a 32-bit value is greater
than 0xffffffffULL.
Reported by Dan Carpenter.
Signed-off-by: Naresh Gottumukkala <bgottumukkala@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
1) ocrdma_remove_free() is called from a call_rcu callback funtion
context, which can be a bottom-half context. So the code in
ocrdma_remove_free should not sleep.
But ocrdma_cleanup_hw() can sleep, So move it ocrdma_remove()
instead of ocrdma_remove_free.
2) Fix a couple of kbuild test robot warnings.
Signed-off-by: Naresh Gottumukkala <bgottumukkala@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We recently added a cap on "max_wqe_allocated" in 43a6b4025c
('RDMA/ocrdma: Create IRD queue fix').
My static checker complains that the cap has a problem because it
casts large values to negative. "attrs->cap.max_send_wr" is a u32.
It comes from the user, but it's capped in ocrdma_check_qp_params() so
it can't wrap here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The Connect-IB adapter has an inherent page size which equals 4K.
Define an new enum that equals the page shift and use it instead of
using the value 12 throughout the code.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
RTS to RTS transition should allow update of alternate path.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
mlx5_cur and mlx5_new cannot have negative values so remove the
redundant condition.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In mlx5_mr_cache_init() the size variable is not used so remove it to
avoid compiler warnings when running with make W=1.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Connect-IB firmware requires 4K pages to be communicated with the
driver. This patch breaks larger pages to 4K units to enable support
for architectures utilizing larger page size, such as PowerPC. This
patch also fixes several places that referred to PAGE_SHIFT instead of
explicit 12 which is the inherent page shift on Connect-IB.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
On destroy QP the driver walks over the relevant CQ and removes CQEs
reported for the destroyed QP. It also frees the related SRQ entry
without checking that this is actually an SRQ-related CQE. In case of
a CQ used for both send and receive QP, we could free SRQ entries for
send CQEs. This patch resolves this issue by verifying that this is a
SRQ related CQE by checking the SRQ number in the CQE is not zero.
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Make use of destroy_srq_kernel() to clear SRQ resouces.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Make sure not to overflow when reading the page list from struct
ib_fast_reg_page_list.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use asynchronous commands to execute up to eight concurrent create MR
commands. This is to fill memory caches faster so we keep consuming
from there. Also, increase timeout for shrinking caches to five
minutes.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Verify that the value is non negative before rounding up to power of 2.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
'op' is the already RDMA_NL_GET_OP() masked 'type'. No need to mask it again.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-by: Yann Droneaud <ydroneaud@opteya.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently, we don't copy the immediate data from the userspace struct
to the kernel one when UD messages are being sent.
This patch makes sure that the immediate data is set correctly.
Signed-off-by: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Since commit 82dc3c63c6 ("net: introduce NAPI_POLL_WEIGHT")
netif_napi_add() produces an error message if a NAPI poll weight
greater than 64 is requested.
Use the standard NAPI weight.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The driver starts the mcast_join task whenever the netdev interface is
UP without relation to the underlying IB port state.
Until the port state is ACTIVE all the join requests are irrelevant,
and the IB core returns -EINVAL. So the user will see errors such as:
"multicast join failed for ff12:401b:... , status -22".
Instead, have ipoib_mcast_join_task() return when the port is not active.
It will be called again when the port state is changed and the
low-level driver triggers the IB_EVENT_PORT_ACTIVE event or the
IB_EVENT_CLIENT_REREGISTER event.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The path_rec_completion() callback may be invoked asynchronously even
at the middle of "driver uninit" process. This can lead to scheduling
a task that tries to touch members of the priv object that are no
longer valid. For example the function cm_create_tx_qp can attempt to
create qp with no valid priv->pd object.
The following crash is one of the results:
RIP: 0010:[<ffffffffa021bb47>] [<ffffffffa021bb47>] ipoib_cm_create_tx_qp+0x57/0x90 [ib_ipoib]
Process ipoib (pid: 5916, threadinfo ffff8803786e4000, task ffff8804150e1500)
Stack:
Call Trace:
[<ffffffff81309ef0>] ? get_random_bytes+0x20/0x30
[<ffffffffa021be2a>] ipoib_cm_tx_init+0xca/0x340 [ib_ipoib]
[<ffffffffa021f765>] ipoib_cm_tx_start+0x215/0x3f0 [ib_ipoib]
[<ffffffffa021f550>] ? ipoib_cm_tx_start+0x0/0x3f0 [ib_ipoib]
[<ffffffff8108b2b0>] worker_thread+0x170/0x2a0
[<ffffffff81090bf0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff8108b140>] ? worker_thread+0x0/0x2a0
[<ffffffff81090886>] kthread+0x96/0xa0
[<ffffffff8100c14a>] child_rip+0xa/0x20
[<ffffffff810907f0>] ? kthread+0x0/0xa0
[<ffffffff8100c140>] ? child_rip+0x0/0x20
Fix that by flushing all pending path queries at this point.
Signed-off-by: Alex Markuze <markuze@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The driver should avoid calling ib_sa_free_multicast on the mcast->mc
object until it finishes its initialization state. Otherwise we can
crash when ipoib_mcast_dev_flush() attempts to use the uninitialized
multicast object.
Instead, only call wait_for_completion() for multicast entries that
started the join process, meaning that ib_sa_join_multicast() finished.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The driver should not flush the whole workqueue when only one work (the
pkey poll one) needs to be cancelled. Use cancel_delayed_work_sync()
instead.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When ipoib interface is going down it takes all of its children with
it, under mutex.
For each child, dev_change_flags() is called. That function calls
ipoib_stop() via the ndo, and causes flush of the workqueue.
Sometimes in the workqueue an __ipoib_dev_flush work() is waiting and
when invoked tries to get the same mutex, which leads to a deadlock,
as seen below.
The solution is to switch to rw-sem instead of mutex.
The deadlock:
[11028.165303] [<ffffffff812b0977>] ? vgacon_scroll+0x107/0x2e0
[11028.171844] [<ffffffff814eaac5>] schedule_timeout+0x215/0x2e0
[11028.178465] [<ffffffff8105a5c3>] ? perf_event_task_sched_out+0x33/0x80
[11028.185962] [<ffffffff814ea743>] wait_for_common+0x123/0x180
[11028.192491] [<ffffffff8105fa40>] ? default_wake_function+0x0/0x20
[11028.199504] [<ffffffff814ea85d>] wait_for_completion+0x1d/0x20
[11028.206224] [<ffffffff8108b4f1>] flush_cpu_workqueue+0x61/0x90
[11028.212948] [<ffffffff8108b5a0>] ? wq_barrier_func+0x0/0x20
[11028.219375] [<ffffffff8108bfc4>] flush_workqueue+0x54/0x80
[11028.225712] [<ffffffffa05a0576>] ipoib_mcast_stop_thread+0x66/0x90 [ib_ipoib]
[11028.233988] [<ffffffffa059ccea>] ipoib_ib_dev_down+0x6a/0x100 [ib_ipoib]
[11028.241678] [<ffffffffa059849a>] ipoib_stop+0x8a/0x140 [ib_ipoib]
[11028.248692] [<ffffffff8142adf1>] dev_close+0x71/0xc0
[11028.254447] [<ffffffff8142a631>] dev_change_flags+0xa1/0x1d0
[11028.261062] [<ffffffffa059851b>] ipoib_stop+0x10b/0x140 [ib_ipoib]
[11028.268172] [<ffffffff8142adf1>] dev_close+0x71/0xc0
[11028.273922] [<ffffffff8142a631>] dev_change_flags+0xa1/0x1d0
[11028.280452] [<ffffffff8148f20b>] devinet_ioctl+0x5eb/0x6a0
[11028.286786] [<ffffffff814903b8>] inet_ioctl+0x88/0xa0
[11028.292633] [<ffffffff8141591a>] sock_ioctl+0x7a/0x280
[11028.298576] [<ffffffff81189012>] vfs_ioctl+0x22/0xa0
[11028.304326] [<ffffffff81140540>] ? unmap_region+0x110/0x130
[11028.310756] [<ffffffff811891b4>] do_vfs_ioctl+0x84/0x580
[11028.316897] [<ffffffff81189731>] sys_ioctl+0x81/0xa0
and
11028.017533] [<ffffffff8105a5c3>] ? perf_event_task_sched_out+0x33/0x80
[11028.025030] [<ffffffff8100bb8e>] ? apic_timer_interrupt+0xe/0x20
[11028.031945] [<ffffffff814eb2ae>] __mutex_lock_slowpath+0x13e/0x180
[11028.039053] [<ffffffff814eb14b>] mutex_lock+0x2b/0x50
[11028.044910] [<ffffffffa059f7e7>] __ipoib_ib_dev_flush+0x37/0x210 [ib_ipoib]
[11028.052894] [<ffffffffa059fa00>] ? ipoib_ib_dev_flush_light+0x0/0x20 [ib_ipoib]
[11028.061363] [<ffffffffa059fa17>] ipoib_ib_dev_flush_light+0x17/0x20 [ib_ipoib]
[11028.069738] [<ffffffff8108b120>] worker_thread+0x170/0x2a0
[11028.076068] [<ffffffff81090990>] ? autoremove_wake_function+0x0/0x40
[11028.083374] [<ffffffff8108afb0>] ? worker_thread+0x0/0x2a0
[11028.089709] [<ffffffff81090626>] kthread+0x96/0xa0
[11028.095266] [<ffffffff8100c0ca>] child_rip+0xa/0x20
[11028.100921] [<ffffffff81090590>] ? kthread+0x0/0xa0
[11028.106573] [<ffffffff8100c0c0>] ? child_rip+0x0/0x20
[11028.112423] INFO: task ifconfig:23640 blocked for more than 120 seconds.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Change CM skb memory allocation to use GFP_KERNEL when possible.
During device init there's no need to use GFP_ATOMIC when allocating
memory for the CM skbs -- use GFP_KERNEL instead.
Signed-off-by: Tal Alon <talal@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If napi has never been enabled when calling ipoib_ib_dev_stop, a
kernel crash occurs, because the verbs layer completion handler
(ipoib_ib_completion) calls napi_schedule unconditionally.
If the napi structure passed in the napi_schedule call has not
been initialized, napi will crash.
The cleanest solution is to simply enable napi before calling
ipoib_ib_dev_stop in the dev_open error flow. (dev_stop then
immediately disables napi).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Physical addresses may be wider than virtual addresses (e.g. on i386
with PAE) and must not be formatted with %p.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Roland Dreier <roland@purestorage.com>
As a simple optimization that should speed up the vast majority of
connect attemps on IB devices, when we are searching for the GID of an
incoming connection in the cached GID lists of devices, search the
device that received the incoming connection request first. If we
don't find it there, then move on to other devices.
This reduces the time to perform 10,000 connections considerably.
Prior to this patch, a bad run of cmtime would look like this:
connect : 12399.26 12351.10 8609.00 1239.93
With this patch, it looks more like this:
connect : 5864.86 5799.80 8876.00 586.49
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The cma_acquire_dev function was changed by commit 3c86aa70bf
("RDMA/cm: Add RDMA CM support for IBoE devices") to use find_gid_port()
because multiport devices might have either IB or IBoE formatted gids.
The old function assumed that all ports on the same device used the
same GID format.
However, when it was changed to use find_gid_port(), we inadvertently
lost usage of the GID cache. This turned out to be a very costly
change. In our testing, each iteration through each index of the GID
table takes roughly 35us. When you have multiple devices in a system,
and the GID you are looking for is on one of the later devices, the
code loops through all of the GID indexes on all of the early devices
before it finally succeeds on the target device. This pathological
search behavior combined with 35us per GID table index retrieval
results in results such as the following from the cmtime application
that's part of the latest librdmacm git repo:
ib1:
step total ms max ms min us us / conn
create id : 29.42 0.04 1.00 2.94
bind addr : 186705.66 19.00 18556.00 18670.57
resolve addr : 41.93 9.68 619.00 4.19
resolve route: 486.93 0.48 101.00 48.69
create qp : 4021.95 6.18 330.00 402.20
connect : 68350.39 68588.17 24632.00 6835.04
disconnect : 1460.43 252.65-1862269.00 146.04
destroy : 41.16 0.04 2.00 4.12
ib0:
step total ms max ms min us us / conn
create id : 28.61 0.68 1.00 2.86
bind addr : 2178.86 2.95 201.00 217.89
resolve addr : 51.26 16.85 845.00 5.13
resolve route: 620.08 0.43 92.00 62.01
create qp : 3344.40 6.36 273.00 334.44
connect : 6435.99 6368.53 7844.00 643.60
disconnect : 5095.38 321.90 757.00 509.54
destroy : 37.13 0.02 2.00 3.71
Clearly, both the bind address and connect operations suffer
a huge penalty for being anything other than the default
GID on the first port in the system.
After applying this patch, the numbers now look like this:
ib1:
step total ms max ms min us us / conn
create id : 30.15 0.03 1.00 3.01
bind addr : 80.27 0.04 7.00 8.03
resolve addr : 43.02 13.53 589.00 4.30
resolve route: 482.90 0.45 100.00 48.29
create qp : 3986.55 5.80 330.00 398.66
connect : 7141.53 7051.29 5005.00 714.15
disconnect : 5038.85 193.63 918.00 503.88
destroy : 37.02 0.04 2.00 3.70
ib0:
step total ms max ms min us us / conn
create id : 34.27 0.05 1.00 3.43
bind addr : 26.45 0.04 1.00 2.64
resolve addr : 38.25 10.54 760.00 3.82
resolve route: 604.79 0.43 97.00 60.48
create qp : 3314.95 6.34 273.00 331.49
connect : 12399.26 12351.10 8609.00 1239.93
disconnect : 5096.76 270.72 1015.00 509.68
destroy : 37.10 0.03 2.00 3.71
It's worth noting that we still suffer a bit of a penalty on
connect to the wrong device, but the penalty is much less than
it used to be. Follow on patches deal with this penalty.
Many thanks to Neil Horman for helping to track the source of
slow function that allowed us to track down the fact that
the original patch I mentioned above backed out cache usage
and identify just how much that impacted the system.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
To guarantee that all unused fields in all FW commands for both inboxes
and outboxes are zeroed out, initialize the mailbox buffer to all zeroes.
This is especially important for SRIOV comm-channel virtual commands
(such as QUERY_FUNC_CAP), where if new fields are added to support new
features, the driver can depend on older kernels passing zeroes in these
fields.
In addition to zeroing out the mailbox buffer at allocation time, all
(now unnecessary) calls to memset by the callers of
mlx4_alloc_cmd_mailbox() are removed.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On top of commit 366cddb40 "IB/rdma_cm: TOS <=> UP mapping for IBoE", add
support for case vlan egress map is used.
When the IBoE session is being set over a vlan, inherit the socket priority
to vlan priority mapping which was configured for the vlan device egress map.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now with percpu refcounting for se_lun in place, go ahead and drop
the legacy per se_cmd accounting for se_lun shutdown.
This includes __transport_clear_lun_from_sessions(), the associated
transport_lun_wait_for_tasks() logic, along with a handful of now
unused se_cmd structure members and ->transport_state bits.
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for completion interrupt coalescing that
allows only every ISERT_COMP_BATCH_COUNT (8) to set IB_SEND_SIGNALED,
thus avoiding completion interrupts for every posted iser_tx_desc.
The batch processing is done using a per isert_conn llist that once
IB_SEND_SIGNALED has been set is saved to tx_desc->comp_llnode_batch,
and completion processing of previously posted iser_tx_descs is done
in a single shot from within isert_send_completion() code.
Note this is only done for response PDUs from ISCSI_OP_SCSI_CMD, and
all other control type of PDU responses will force an implicit batch
drain to occur.
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is step #1 for implementing SRIOV resource quotas for VFs.
Quotas are implemented per resource type for VFs and the PF, to prevent
any entity from simply grabbing all the resources for itself and leaving
the other entities unable to obtain such resources.
Resources which are allocated using quotas: QPs, CQs, SRQs, MPTs, MTTs, MAC,
VLAN, and Counters.
The quota system works as follows:
Each entity (VF or PF) is given a max number of a given resource (its quota),
and a guaranteed minimum number for each resource (starvation prevention).
For QPs, CQs, SRQs, MPTs and MTTs:
50% of the available quantity for the resource is divided equally among
the PF and all the active VFs (i.e., the number of VFs in the mlx4_core module
parameter "num_vfs"). This 50% represents the "guaranteed minimum" pool.
The other 50% is the "free pool", allocated on a first-come-first-serve basis.
For each VF/PF, resources are first allocated from its "guaranteed-minimum"
pool. When that pool is exhausted, the driver attempts to allocate from
the resource "free-pool".
The quota (i.e., max) for the VFs and the PF is:
The free-pool amount (50% of the real max) + the guaranteed minimum
For MACs:
Guarantee 2 MACs per VF/PF per port. As a result, since we have only
128 MACs per port, reduce the allowable number of VFs from 64 to 63.
Any remaining MACs are put into a free pool.
For VLANs:
For the PF, the per-port quota is 128 and guarantee is 64
(to allow the PF to register at least a VLAN per VF in VST mode).
For the VFs, the per-port quota is 64 and the guarantee is 0.
We assume that VGT VFs are trusted not to abuse the VLAN resource.
For Counters:
For all functions (PF and VFs), the quota is 128 and the guarantee is 0.
In this patch, we define the needed structures, which are added to the
resource-tracker struct. In addition, we do initialization
for the resource quota, and adjust the query_device response to use quotas
rather than resource maxima.
As part of the implementation, we introduce a new field in
mlx4_dev: quotas. This field holds the resource quotas used
to report maxima to the upper layers (ib_core, via query_device).
The HCA maxima of these values are passed to the VFs (via
QUERY_HCA) so that they may continue to use these in handling
QPs, CQs, SRQs and MPTs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/netconsole.c
net/bridge/br_private.h
Three mostly trivial conflicts.
The net/bridge/br_private.h conflict was a function signature (argument
addition) change overlapping with the extern removals from Joe Perches.
In drivers/net/netconsole.c we had one change adjusting a printk message
whilst another changed "printk(KERN_INFO" into "pr_info(".
Lastly, the emulex change was a new inline function addition overlapping
with Joe Perches's extern removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target pending fixes for v3.12-rc7.
This includes a number of EXTENDED_COPY related fixes as a result of
Thomas and Doug's continuing testing and feedback.
Also included is an important vhost/scsi fix that addresses a long
standing issue where the 'write' parameter for get_user_pages_fast()
was incorrectly set for virtio-scsi WRITEs -> DMA_TO_DEVICE, and not
for virtio-scsi READs -> DMA_FROM_DEVICE.
This resulted in random userspace segfaults and other unpleasantness
on KVM host, and unfortunately has been an issue since the initial
merge of vhost/scsi in v3.6. This patch is CC'ed to stable, along
with two other less critical items"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
vhost/scsi: Fix incorrect usage of get_user_pages_fast write parameter
target/pscsi: fix return value check
target: Fail XCOPY for non matching source + destination block_size
target: Generate failure for XCOPY I/O with non-zero scsi_status
target: Add missing XCOPY I/O operation sense_buffer
iser-target: check device before dereferencing its variable
target: Return an error for WRITE SAME with ANCHOR==1
target: Fix assignment of LUN in tracepoints
target: Reject EXTENDED_COPY when emulate_3pc is disabled
target: Allow non zero ListID in EXTENDED_COPY parameter list
target: Make target_do_xcopy failures return INVALID_PARAMETER_LIST
This patch changes isert_connect_release() to correctly check for
the existence struct isert_device *device before checking for
isert_device->use_frwr.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The create_flow/destroy_flow uverbs and the associated extensions to
the user-kernel verbs ABI are under review and are too experimental to
freeze at this point.
So userspace is not exposed to experimental features and an uinstable
ABI, temporarily disable this for v3.12 (with a Kconfig option behind
staging to reenable it if desired).
The feature will be enabled after proper cleanup for v3.13.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://marc.info/?i=cover.1381351016.git.ydroneaud@opteya.com
Link: http://marc.info/?i=cover.1381177342.git.ydroneaud@opteya.com
[ Add a Kconfig option to reenable these verbs. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
one trivial semicolon cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=0XuA
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Last batch of IB changes for 3.12: many mlx5 hardware driver fixes
plus one trivial semicolon cleanup"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB: Remove unnecessary semicolons
IB/mlx5: Ensure proper synchronization accessing memory
IB/mlx5: Fix alignment of reg umr gather buffers
IB/mlx5: Fix eq names to display nicely in /proc/interrupts
mlx5: Fix error code translation from firmware to driver
IB/mlx5: Fix opt param mask according to firmware spec
mlx5: Fix opt param mask for sq err to rts transition
IB/mlx5: Disable atomic operations
mlx5: Fix layout of struct mlx5_init_seg
mlx5: Keep polling to reclaim pages while any returned
IB/mlx5: Avoid async events on invalid port number
IB/mlx5: Decrease memory consumption of mr caches
mlx5: Remove checksum on command interface commands
IB/mlx5: Fix memory leak in mlx5_ib_create_srq
IB/mlx5: Flush cache workqueue before destroying it
IB/mlx5: Fix send work queue size calculation
Call mlx5_ib_populate_pas() before mapping the DMA buffer to ensure
the hardware reads the values written by the CPU.
Found by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The hardware requires that gather buffers for UMR work requests be
aligned to 2K.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
It's helpful for a driver to put the pci slot name in its interrupt
names, so /proc/interrupts will show the pci slot of the device.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Failed to configure opt mask to configure rre from init to rtr.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently Atomic operations don't work properly. Disable them for the
time being.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
On a single ported Connect-IB, its possible for the firmware to issue
events on the non-existing 2nd port. Make sure to ignore events
generated for such ports.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Change the logic so we do not allocate memory nor map the device
before actually posting to the REG_UMR QP. In addition, unmap and free
the memory after we get completion.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The patch fixes the rollback in case of failure in creating SRQ.
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Destroying the workqueue without flushing it first can lead to a case
in which the kernel tries to push a delayed work to the workqueue
which does not exist anymore.
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
1. Make sure wqe_cnt does not exceed the limit published by firmware.
2. There is no requirement that the number of outstanding work
requests will be a power of two. Remove the ilog2 in the
calculation of sq.max_post to fix that.
3. Add case for IB_QPT_XRC_TGT in sq_overhead and return 0 as XRC
target QPs do not have a send queue.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The callers of qib_tune_pcie_caps() and qib_tune_pcie_coalesce() don't
check the return values, so this patch drops the return values altogether.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
The SRP specification requires:
"Response data shall be provided in any SRP_RSP response that is sent in
response to an SRP_TSK_MGMT request (see 6.7). The information in the
RSP_CODE field (see table 24) shall indicate the completion status of
the task management function."
So fix this to avoid the SRP initiator interprets task management functions
that succeeded as failed.
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Cc: stable@vger.kernel.org # 3.3+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where ib_destroy_cm_id() was incorrectly being called
after srpt_destroy_ch_ib() had destroyed the active QP.
This would result in the following failed SRP_LOGIN_REQ messages:
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff1762bd, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c903009f8f41)
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff1758f9, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 2 (guid=0xfe80000000000000:0x2c903009f8f42)
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff175941, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 2 (guid=0xfe80000000000000:0x2c90300a3cfb2)
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff176299, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c90300a3cfb1)
mlx4_core 0000:84:00.0: command 0x19 failed: fw status = 0x9
rejected SRP_LOGIN_REQ because creating a new RDMA channel failed.
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff176299, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c90300a3cfb1)
mlx4_core 0000:84:00.0: command 0x19 failed: fw status = 0x9
rejected SRP_LOGIN_REQ because creating a new RDMA channel failed.
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff176299, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c90300a3cfb1)
Reported-by: Navin Ahuja <navin.ahuja@saratoga-speed.com>
Cc: stable@vger.kernel.org # 3.3+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- Move sysctl_local_ports from a global variable into struct netns_ipv4.
- Modify inet_get_local_port_range to take a struct net, and update all
of the callers.
- Move the initialization of sysctl_local_ports into
sysctl_net_ipv4.c:ipv4_sysctl_init_net from inet_connection_sock.c
v2:
- Ensure indentation used tabs
- Fixed ip.h so it applies cleanly to todays net-next
v3:
- Compile fixes of strange callers of inet_get_local_port_range.
This patch now successfully passes an allmodconfig build.
Removed manual inlining of inet_get_local_port_range in ipv4_local_port_range
Originally-by: Samya <samya@twitter.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor qib_tune_pcie_caps(). Use pcie_get_mps(), pcie_set_mps(),
pcie_get_readrq(), and pcie_set_readrq() to simplify the code. The PCI
core caches the "PCIe Max Payload Size Supported" in pci_dev->pcie_mpss,
so use that instead of pcie_capability_read_word(). Remove the unused
val2fld() and fld2val().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Use pci_is_root_bus() instead of "if (bus->parent)" statement
for better readability.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Alexander Gordeev